in pc_system.h to flag each timer slot as being allocated or not.
register_timer*() functions will claim a free slot if one
exists before using one at the end of the list. This will allow
for this function to be called repeatedly and not have to run
out of timer slots.
wants to free up that resource.
unsigned unregisterTimer(int timerID);
Pass in the timer index received from the register function. A return
of 1 means success. NOTE: you must make sure the timer is deactivated
first. Call deactivate_timer() to be sure. A return of 0 means
failure, though a panic is really generated.
For now, this function does not really free up the slot, but will soon.
32-bits rather than 64. This is possible, because there is
always an active null (heartbeat) timer, with periodicity
of less than or equal to the maximum 32-bit int value.
This generates a little less code in the hot part of cpu_loop,
and saved about 3% execution time on a Win95 boot.
Moved the asynchronous handling code from cpu_loop() to its
own function since it's a long path. This neatened up the
code a little (less gotos and all), and made it more clear
to use a "while (1)" around the iterative code in cpu_loop().
These seem to be working better, are a more simple design,
easier to understand, and AFAIK don't have race conditions
in them like the old ones do.
Re-coded the apic timer, to return cycle accurate values
which vary with each iteration of a read from a guest OS.
The previous implementation had very poor resolution. It
also didn't check the mask bit to see if an apic timer
interrupt should occur on countdown to 0. The apic timer
now calls its own bochs timer, rather than tag on the
one in iodev/devices.cc.
I needed to use one new function which is an inline in
pc_sytem.h. That would have to be added to the old pc_system.h if
we have to back-out to it.
Linux/x86-64 now boots until it hits two undefined opcodes:
FXRSTOR (0f ae). This restores FPU, MMX, XMM and MXCSR registers
from a 512-byte region of memory. We don't implement this yet.
MOVNTDQ (66 0f e7). This is a move involving an XMM register.
The 0x66 prefix is used so it's a double quadword, rather than
MOVNTQ (0f e7) which operates on a single quadword.
The Linux kernel panic is on the MOVNTQD opcodes. Perhaps that's
because that opcode is used in exception handling of the 1st?
Looks like we need to implement some new instructions.
requesting source can be registered as well. Otherwise, there
is no way to know which source modules are requesting
suspect frequencies which are too high.
up pc_system.h. Moved all variables under the private: section,
as well as a few member functions. The string instructions
were accessing a field directly (only reads), so I indirected
that via an inline member function for better abstraction.
- Paging code rehash. You must now use --enable-4meg-pages to
use 4Meg pages, with the default of disabled, since we don't well
support 4Meg pages yet. Paging table walks model a real CPU
more closely now, and I fixed some bugs in the old logic.
- Segment check redundancy elimination. After a segment is loaded,
reads and writes are marked when a segment type check succeeds, and
they are skipped thereafter, when possible.
- Repeated IO and memory string copy acceleration. Only some variants
of instructions are available on all platforms, word and dword
variants only on x86 for the moment due to alignment and endian issues.
This is compiled in currently with no option - I should add a configure
option.
- Added a guest linear address to host TLB. Actually, I just stick
the host address (mem.vector[addr] address) in the upper 29 bits
of the field 'combined_access' since they are unused. Convenient
for now. I'm only storing page frame addresses. This was the
simplest for of such a TLB. We can likely enhance this. Also,
I only accelerated the normal read/write routines in access.cc.
Could also modify the read-modify-write versions too. You must
use --enable-guest2host-tlb, to try this out. Currently speeds
up Win95 boot time by about 3.5% for me. More ground to cover...
- Minor mods to CPUI/MOV_CdRd for CMOV.
- Integrated enhancements from Volker to getHostMemAddr() for PCI
being enabled.
DMA functions defined. Most of the changes are based on the "bochs sync"
version of plex86. Here is the list of changes:
* register/unregister functions for DMA channels added. The DMA controller
can use the DMA read/write handlers of registered devices directly.
* "hardwired" code in dma.cc removed
* all DMA related code in devices.cc and iodev.h removed
* DMA related code in pc_system.* removed except HRQ handling
* macros for DMA functions defined in bochs.h
* floppy and SB16 code modified to use the changes described above
in BRANCH-smp-bochs revisions.
- The general task was to make multiple CPU's which communicate
through their APICs. So instead of BX_CPU and BX_MEM, we now have
BX_CPU(x) and BX_MEM(y). For an SMP simulation you have several
processors in a shared memory space, so there might be processors
BX_CPU(0..3) but only one memory space BX_MEM(0). For cosimulation,
you could have BX_CPU(0) with BX_MEM(0), then BX_CPU(1) with
BX_MEM(1). WARNING: Cosimulation is almost certainly broken by the
SMP changes.
- to simulate multiple CPUs, you have to give each CPU time to execute
in turn. This is currently implemented using debugger guards. The
cpu loop steps one CPU for a few instructions, then steps the
next CPU for a few instructions, etc.
- there is some limited support in the debugger for two CPUs, for
example printing information from each CPU when single stepping.
To see the commit logs for this use either cvsweb or
cvs update -r BRANCH-io-cleanup and then 'cvs log' the various files.
In general this provides a generic interface for logging.
logfunctions:: is a class that is inherited by some classes, and also
. allocated as a standalone global called 'genlog'. All logging uses
. one of the ::info(), ::error(), ::ldebug(), ::panic() methods of this
. class through 'BX_INFO(), BX_ERROR(), BX_DEBUG(), BX_PANIC()' macros
. respectively.
.
. An example usage:
. BX_INFO(("Hello, World!\n"));
iofunctions:: is a class that is allocated once by default, and assigned
as the iofunction of each logfunctions instance. It is this class that
maintains the file descriptor and other output related code, at this
point using vfprintf(). At some future point, someone may choose to
write a gui 'console' for bochs to which messages would be redirected
simply by assigning a different iofunction class to the various logfunctions
objects.
More cleanup is coming, but this works for now. If you want to see alot
of debugging output, in main.cc, change onoff[LOGLEV_DEBUG]=0 to =1.
Comments, bugs, flames, to me: todd@fries.net
