choice of hexadecimal and/or character displays of the memory data, with
different digit grouping sizes. Still needs some work but is basically
functional.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42204 a95241bf-73f2-0310-859d-f6bbb57e9c96
a whole second until the message runner kicks in.
* This should further reduce the time the mouse pointer sits uselessly on the
screen.
* This is not a fix of #917, but makes it hopefully less annoying.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42199 a95241bf-73f2-0310-859d-f6bbb57e9c96
directly reduces the time the mouse cursor is visible but cannot be moved
yet. Based on a patch by Adek336 as part of ticket #917.
* Decreased the republishing snooze about a second, too.
* Minor cleanup.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42198 a95241bf-73f2-0310-859d-f6bbb57e9c96
Plan to move gRegister into the crt struct at some point.
* Few style fixes
* Added function to probe edid of attached monitors and populate CRT info
* Disable VGA control modifications temporarly while I hammer out some issues.
* Fix radeon card model checks (bitwise & is not |)
* Finally fix? blanking start / end calculations using porch
* Use mask for setting sync polarity
* Add overscan (8 pixels is default?)
* Disable PLLSet/Power for the moment as it seems to muck things up.
* is_mode_supported now validates if a mode line is with the monitors
h/v sync frequencies (how does is_mode_supported know what crt the os wants?)
* PLL Write/Read don't actually use the PLL Write/Read functions (thanks AMD!)
* Added better PLL legacy (r600-r610) support
* Consistantly give no DCCG on legacy cards.
* Tracing!
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42191 a95241bf-73f2-0310-859d-f6bbb57e9c96
specified the syscall error code B_WOULD_BLOCK would no longer be mapped to 0.
Fixes#7693.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42188 a95241bf-73f2-0310-859d-f6bbb57e9c96
most headers refer to can be found. Fixes the build under Haiku (ticket #7688).
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42187 a95241bf-73f2-0310-859d-f6bbb57e9c96
arguments and environment. Fixes failures to start programs in case the space
available through rounding to full page sizes wasn't sufficient.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42184 a95241bf-73f2-0310-859d-f6bbb57e9c96
exit info with some generic status.
* team_create_thread_start(), common_thread_entry(): Initializes the team's
exit info (if that's the main thread) before calling thread_exit(). Fixes
#7686.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42183 a95241bf-73f2-0310-859d-f6bbb57e9c96
* Only try to cancel the a transfer, if sUseUSBKeyboard is set.
* Set the "_usbPipe" parameter.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42181 a95241bf-73f2-0310-859d-f6bbb57e9c96
* libbe_build: Where possible we directly use the actual Haiku headers and
sources, now. In the headers/build headers we just include the respective
Haiku headers as needed. That still allows overrides where necessary. The
intention is to make it easier to keep the build stuff in sync.
* Fixed a few printf() format and signed/unsigned comparison warnings.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42179 a95241bf-73f2-0310-859d-f6bbb57e9c96
HAIKU_TARGET_PLATFORM_HAIKU, so the file can also be compiled for the host
platform.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42178 a95241bf-73f2-0310-859d-f6bbb57e9c96
* Actually start rendering the memory data. Still has some drawing glitches
when scrolling though, will look into those tomorrow. Also doesn't yet
highlight the location which the target address actually points to within
the block.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42167 a95241bf-73f2-0310-859d-f6bbb57e9c96
[u]int32 and [u]int64 to avoid clashes with the int/unsigned int versions.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42165 a95241bf-73f2-0310-859d-f6bbb57e9c96
allows the use of stty to configure the serial device and later using other
commands with these settings still in place.
* Store incoming termios settings when they are set, restore the previous
settings on open and apply the control modes to the device side as well.
* Only send the control to the system side tty cookie again. Doing it for both
cookies was only done to configure the termios, which isn't necessary anymore.
* Remove fallbacks to c_{i|o}speed fields and always use c_cflag & CBAUD for the
single speed setting we have.
* Remove some leftover control line state logic that doesn't apply anymore.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42161 a95241bf-73f2-0310-859d-f6bbb57e9c96
how one could actually apply different speeds, make cf{set|get}{i|o}speed() use
the c_cflag field with the CBAUD mask instead.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42160 a95241bf-73f2-0310-859d-f6bbb57e9c96
* Make index numbering consistant (0-n vs 1-n)
* Add a little more tracing to PLLCalibrate because
we were missing a failure situation
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42158 a95241bf-73f2-0310-859d-f6bbb57e9c96
ensure that we don't block on the tty buffer, we chop up the data into blocks
that are written into the tty and then the buffer is flushed to the device
each time. This resolves the issue that a quick open/write/close would not
actually send the data to the device as it would cancel the transfer before
the output thread had a chance to run.
* Use the tty_close_cookie() call. Doing the close before waiting for the input
thread ensures that it is woken up if it blocked on writing into the tty.
* Correct the type of the USB callback status and only try to clear a halt if
the device was actually stalled.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42156 a95241bf-73f2-0310-859d-f6bbb57e9c96
available as a module function as well.
* Remove some unneeded resetting from tty_destroy_cookie.
* Move the public module functions to the public API section of the file and
order them by their declaration order in the module info.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42154 a95241bf-73f2-0310-859d-f6bbb57e9c96
before assuming we have data. If the I/O port isn't valid (e.g. because there
is no serial port) 0xff seems to be a typical value to read. In that case fail.
Fixes KDL input on machines without serial port -- kgetc() would always think
it read something from the serial port, never trying any other input.
git-svn-id: file:///srv/svn/repos/haiku/haiku/trunk@42153 a95241bf-73f2-0310-859d-f6bbb57e9c96
Alexander von Gluck IV