for the registers, which was true, but actually the same as the driver
did without this option.
What it realy did is work around a stupid bug in the driver that did not
use the "offset" result from the pcmcia_mem_map call mapping the CIS memory.
We got away with this for a long time since on i386 and typical pcmcia
bridged the offset returned will be 0. It always failed (without
RAY_USE_AMEM=1) if the check for a different function CCR aliases in pcmcia.c
failed and mapped the CCR base new - this time at the CCR base of this
function (0xf00), so all register acceses (that had 0xf00 added) happened
way off in neverland.
Now we do not hardcode the CCR base to the register definitions, but
instead use the offset returned by pcmcia_mem_map. This makes the driver
work with and without CCR base aliases being found.
Configure power supply on VPP1 at 5V when powering up a socket.
Get rid of stray interrupts.
Make the driver quiet for normal operation when not in debugging mode.
This makes ray0 at nell0 actually work when compiled with RAY_USE_AMEM=1.
deal with shortages of the VM maps where the backing pages are mapped
(usually kmem_map). Try to deal with this:
* Group all information about the backend allocator for a pool in a
separate structure. The pool references this structure, rather than
the individual fields.
* Change the pool_init() API accordingly, and adjust all callers.
* Link all pools using the same backend allocator on a list.
* The backend allocator is responsible for waiting for physical memory
to become available, but will still fail if it cannot callocate KVA
space for the pages. If this happens, carefully drain all pools using
the same backend allocator, so that some KVA space can be freed.
* Change pool_reclaim() to indicate if it actually succeeded in freeing
some pages, and use that information to make draining easier and more
efficient.
* Get rid of PR_URGENT. There was only one use of it, and it could be
dealt with by the caller.
From art@openbsd.org.
http://mail-index.netbsd.org/tech-kern/2002/03/04/0005.html
auconv.c: Add conversion functions
audio.c: Sample alignment, calling conversion functions, etc.
audio_if.h: Add four hw_* members to "struct audio_params"
audiovar.h: Add conversion buffers, etc.
auich and uaudio: Add conversion request code to *_set_params().
it worked- but I ran into a case with a 2204 where commands were being lost
right and left. Best be safe.
For target mode, or things called if we call isp_handle_other response- note
that we might have dropped locks by changing the output pointer so we bail
from the loop. It's the responsibility of the entity dropping the lock to
make sure that we let the f/w know we've read thus far into the response
queue (else we begin processing the same entries again- blech!).
- Change structures for each device to make them more suitable with
our scsipi mid-layer.
- Use ADAPTER_REQ_SET_XFER_MODE callback.
- Cleanup misc functions/structures/style.
XXX Tagged queuieng support is disabled for now.
XXX Maybe we should have common library of the scsi protocol engine
XXX to share it among all other drivers..
Allow SIOCSWAVELAN with WI_RID_IFACE_STATS to request
an immediate statistics update.
We might in the future want to have SIOCGWAVELAN with
WI_RID_IFACE_STATS return an error if a statistics gathering is in
progress. Then the caller could request fresh statistics and gather
them when they are done. Instead, we currently just return whatever
statistics are available, which may be up to 60 seconds old.
chipset functions acordingly. Initialize timing registers (for now to
the slowest possible setting).
Add some debug output. XXX - clean this up.
This is not ready for prime time, but I can attach ray0 and wi0 now in my
LX.
jumbo frames.
* Work around broken PXE firmware on some boards, which leave the ROM
BAR enabled even after the PXE stack has been unloaded.
* Set up the initial values for sc_tx_fill_thresh, sc_tx_drain_thresh, and
sc_rx_drain_thresh in sip_attach(), rather than in sip_init().
Also, add unit location fields to the ROM image. The p1212 spec requires
unit locations if you have 2 or more unit directories which is the case for
ipv4 and ipv6 compiled into a kernel.
filling in unit location in the rom.
XXX: This all is really too welded together. The if_fw code should be
decoupled from this and simply be handed a method by which it can provide
the config rom back to the main code.
A framework for parsing p1212 compliant ROM's and returning a tree that
describes it. Include routines for searching the tree, walking it to
apply functions against nodes and printing out the tree.
Also provide a utility routine to take all the unit dirs present in a ROM,
loop against them and present them to config_found to configure all possible
sub devices.
the center position (128), so as to be compatible with other drivers.
The equalizer is enhancement only, and the values < 128 don't take
any effect.
Yeah, this causes spec change....
For equalization.treble and equalization.bass, the relation between
old and new value is
new_value = (old_value / 2) + 128.
(Note this does not apply to equalization.surround.)
2. Support ++ and -- of mixerctl(1) for stepping volume variables.
3. Fix problem where the chip is not powered up
when the mic input is unmuted.
this partially addresses pr14385.
there is still a byte swapping bug retrieving the
stats structure. Since both the type and the length
are incorrectly swapped, we would timeout while reading
an extra long section (caused by the byteswapped length)
of garbage data.
turning on WI_DEBUG now just reports the unknown info type
which can be seen to be obviously incorrectly swapped
on macppc
locations. If passed NULL, the old behaviour using bus_space_{read,write}_1()
is used. Otherwise, all access to the chip goes via the MD functions.
This is necessary for mvmeppc boards where the mk48txx NVRAM/RTC is not
directly addressable.
Distinguish between 2312 and 2300 cards (they *are* different). Enable
RIO (Reduced Interrupt Operation) for the LVD cards (hey- I've seen
batched completions of the 30 commands at a time with this,....)...
If we get a Port Logout on local loop topologies, we have to force the
f/w to log back in. The easiest way (for us) to do this is to force
a LIP. This also will wake up the disk that probably just had a f/w crash.
Implement mailbox 'continuations'- this allows interrupts to re-drive
a mailbox command if it's one that just essentially repeats the previous
mailbox command (e.g., f/w download). This saves a boatload of sleep/wakeup
twitches.
If we're not a 2300 and we're about to return with a 'bogus interrupt'- check
the semaphore register to be non-zero at all and outgoing mailbox 0- this
seems to be where some of the lost ISP1080 commands came from.
a byte-size quantity, the CacheLine Size configuration register specifies
the system cacheline size in units of 32-bit words; per PCI Local Bus
Specification, rev. 2.1, section 6.2.4.
joda