has the console input device. The USB keyboard driver uses this to
attach the first USB keyboard instance as the console keyboard.
Unfortunately, this must still be deferred to autoconfiguration time,
but there's not much we can do about that right now.
By code inspection I found 2 bugs in the ATAPI code, one may be the cause
of your problem: A counter is not reset when issuing the request_sense
command. This is c_skip, the counter used to track the offset in the data
buffer when a data tranfer needs multiple phases. The effect of this is that
the sense data transfered may be stored outside the sense buffer (sense buffer
+ some, potentially several KB, offset). This can only occur in PIO mode,
DMA is not affected.
This doesn't occur in "normal" use because when reading a data CD, either
the sense is issued for a non-data command (in which case c_skip stays to
0), or an error occured and no data has been transfered, and c_skip is still 0.
I can't see a case where a data READ/WRITE could cause a sense tranfer without
error.
The second problem is that b_resid can be set to a false value (resulting of
the sense tranfer and not the data transfer). Again this is not a problem with
usual data tranfers because both values ends up being 0 when no error occurs.
return 0 instead of EINVAL. In this case, there will only be one media
type, and the upper-level if_media code will ensure that the user is setting
to that type.
In other words, don't require the front-end to provide the no-op.
- Initialize more of the Bt463's registers, instead of leaving them
in undefined states. Notably, the window type table is set up
with 8-plane pseudocolor and 24-plane truecolor modes.
- Bus-space-ify, mostly. Could use some more cleanup, but not until
the rest of the tga stuff is converted, too.
- Do the TGA/RAMDAC communication dance more carefully.
- Explain a lot more of what's going on in comments.
Reorganise the driver some what.
Rename tr_reset() to the more appropriate tr_stop().
Create a common tropic reset routine and use it in the frontends.
Move the code in tr_config() which is only used in the card attachment
routines into a new tr_attach() function.
Take adapter off the ring through tr_shutdown() in a shutdown hook.
This simplifies the bus-specific frontend.
Verify EEPROM checksum, extract card rev-level, test capabilities
word, then test high-order config bits to verify card is in PnP mode,
and skip if so.
* resid in pcscp_dma_intr() should also be set in the data out phase.
* Don't set up DMA in the transfer pad operations.
* Change URL of the PDF technical manual to the index page.
* include <machine/bswap.h> on big endian machines.
Fixes timeouts writing large blocks to tapes. From Izumi Tsutsui,
PR 7252.
per-packet discard of every received packet increases latency and
decrease throughput. INstead, Spin on S_COMMAND_IN_PROGESS for enough
iterations as the expected time to completion. Only do DELAY()/poll
loops (as suggested by Jason Thorpe) if spinning fails.
Take PCI as fastest case and compute worst-case estimate.
Shorten DELAY() in S_COMMAND_COMPLETE polling-loop up 10, loop-count
down. to speed up epreset() completion (m/c filter change, ifup/ipdown, etc).
* Clear the `enabled' bit in the softc so late hardware interrupts
(e.g., just after the full reset) done as part of shutdown) are dropped.
* Eliminate loops that poll forever on S_COMMAND_IN_PROGRESS to complete.
Add inline function with bounded loopcount plus small delay, to avoid
bugs in EISA hardware which never sets S_COMMAND_IN_PROGRESS.
Use for both TX_RESET/RX_RESET/GLOBAL_RESET cmds, and polling for
discard-Rx completion
EIO. The spec says ATAPI devices should support "PIO 3 or better".
They are supposed to support less as well. Setting the device to a highter
mode than the controller shoul'nt be a problem, and this is likely what
happens with legaty ISA controllers.
Solve problem reported by Ruey-Shyang Guo.
Big-endian CPUs should use bus_space_{read,write}_multi_stream methods
to PIO packet data to NIC in 16-bit or 32-bit chunks.
Make it so.
Since we don't have stream methods on all ports yet (esp. i386), use
the bus_space_{read,write}_multi methods if the compile-time
stream-method feature-test macro is not set.
Originally from tsubai@netbsd.org, via HAYAKAWA koichi's cardbus patches.
we can identify them as cardbus chips supported by the cardbus patches.
Add entry for OPTI chipsets whose interrupts arent properly set up by
some BIOSes.
From cardbus patches<ftp://nandra.iri.co.jp/pub/NetBSD/CardBus by
HAYAKAWA Koichi <haya@tcad.ulsi.sony.co.jp>.
- Don't rely on ATA signature: some ide controllers seems to not transmit it
properly (SIMIDE on arm32 machines). Instead, when we guess a drive is here
after reset, just mark it as ATA and OLD is it's not ATAPI.
- at attach time, use IDENTIFY to eliminate ghost from the probe. If the
drive had the old flag and IDENTIFY failed, issue a WDCC_RECAL command
to detect a pre-ATA disk. If IDENTIFY succeded, remove the OLD flag,
it's obviously not a pre-ATA disk.
- add a new controller flag, WDC_CAPABILITY_PREATA, used to shorcut parts
of the probe (not necessary, but makes the probe/attach faster). This is
only set by the ISA front-end, all other controllers supported can't have
pre-ATA drives attached.
The mechanism used are more or less the same as before, they have just been
reordered. Should solve port-arm32/7324 (waiting for feedback).
- the cap field is a u_int8_t, so none of the defined flags would fit in.
Looks like nobody had a drive using 16 bytes commands.
- the ACAP_DRQ_* flags are all wrong. Just remove them and use the definitions
from ata/atareg.h, there's no need to duplicate theses. The effect of this
was that we were always polling for the command phase, even for drives
with interrupt DRQ. This didn't break until the code was changed to support
shared interrupts.
Should fix the lookup problems or 'boot hangs' reported by some users, and
kern/7111.
clean bit. This is somewhat bogus as RAID 0 does not have any parity,
but is a slightly cleaner than other solutions, and makes the handling
of clean bits for RAID 0 consistent with the handling of clean bits at
other RAID levels.
board versions with no BIOS. Separate mailbox interrupts from
IOCB interrupts. Read OUTMAILBOX5 while RISC_INT is active- not
after you clear it (potential race condition). Clear out older broken
BIG_ENDIAN goop. Don't negotiate narrow/async for LVD busses at startup
if already in LVD mode. Note usage of presumptive 1040C revision. For
all the LIP, PDB Changed, Loop UP/DOWN async events, mark fw state
as unknown as well as marking the need to do a getpdb on targets- after
a LIP for certain the f/w has to do PRLI/PLOGI for all targets again
and marking f/w state as unknown gives us a fighting chance to (start
to) hold up for that to complete.
that will SBusify an isp header or the lun/target portions of a request IOCB-
and have these only valid iff __sparc__ (no non-sparc SBus machine that *I*
know about).
was deasserted and we wanted to change parameters to -crtscts
This effectively stalled the transmitter since with TS_BUSY set
we only change parameters during the Tx interrupt handler.
are called from the interrupt or timeout handler, 0 otherwise.
- use this to know if we can busy-wait for wait_for_unbusy or wait_for_ready
This fixes a bug where CDs withot the DRQ_INTR capability would not busy-wait
for the CMDOUT phase.
While I'm there change 2 delay() to DELAY() for consistency, and
garbage-collect some old code from wdcintr() which has been ifdef'd out
for some time now.
TULIP_BUSMODE_BIGENDIAN does bswap packet buffers also, so we should use
TULIP_BUSMODE_DESC_BIGENDIAN on big-endian machines. (PR 7027)
XXX 21040 doesn't have this bit, but supporting only 21041+ is better than
nothing.
DELAY(1)'s. This should fix interrupt driven lpt driver hang and
reboot problems for the group of users who have experienced them, and
shouldn't hurt anyone else.
* The fact that IIR_NOPEND was not set on entry does *not* mean that no
transmission was in progress. Besides, we don't want to throw away receive
interrupts either.
* In the !clearirq case, we didn't splx().
1. don't clear the irq unless it was clear before transmitting
2. also do various bus_space_barrier() ops
Stops console from freezing when kprintf interrupts tty driver output.
IDENTIFY said so: it doesn't help for the drive this was supposed helping,
and seems to break another device.
In interrupt routine, don't return 0 if we are polling: this should fix the
"panic: wdc_exec_command: polled command not done" some people reported
(kern/7269).
and ignore the error. Scanset 2 should be the default after reset, so
this allows some broken keyboards to work. (Reset is needed because at
least 1 keyboard locks up if the "set scanset" is attempted.)
& strobe cycle. These bracket DELAY()'s of BROKEN_LPT_DELAY
microseconds. This can be used to kludge around mysterious hangs and
reboots some users experience. The cause of these failures is still
not known, but is conjectured to be hardware bug originated failures
in the bus cycle.
in not just used to access memory but is bassed to bus_space_xxx_n()
methods. For debugging purposes, bus_space can have additional constraints
which will be properly met by BUS_SPACE_ALIGNED_POINTER().
* Rearrange the speed mapping table and adjust the code so that the highest
rate can actually be used. Previously we ended up rounding up slightly
lower speeds and then losing because set_params couldn't set the mode
back to the current one.
* Allow 260 as a valid I/O address, since the SB1 can be jumpered to this.
* Change the MPU-401 code so it can be attached as a separate device.
(XXX Really, the SB code ought to just attach a subdevice itself.)
* Do not attach an OPL on the SB1. Writing to the OPL registers at
SB_base+0 on this card wedges my machine.
(XXX Should we access it at 388 instead? The Creative web site claims
that this board *does* have an OPL2, but I haven't played with this
extensively.)
* Allocate the SB DMA channels at open time, rather than attach time, so
that a single DRQ can be used for multiple cards (if only one is in use
at a given time).
(XXX Let me tell you why this is a horrible hack. If the ISA DMA code
tries to allocate a bounce buffer after boot time, it will generally fail,
because there is no contiguous memory below 16MB and the code to allocate
contiguous pages doesn't know how to move things around. Now, we
shouldn't ever be using bounce buffers here, because we use
isa_dmamem_alloc(). So we just turn off BUS_DMA_ALLOCNOW and we don't
actually try to. That's cool, and it even works, but isa_dmamem_alloc()
has the same problem. It just happens that we allocate the ring buffers
at boot time, and whenever we reallocate them (due to the buffer size
changing), we just deallocated the previous (contiguous) buffer, so we get
lucky. This is absolutely disgusting and needs to be fixed.)
* Use a single routine to halt both input and output on Audio1.
* Reduce the number of register reads/writes used to set up a channel.
* A few other minor things.
* Separate the interrupt handlers based on which channel (audio1/audio2)
rather than which direction (input/output). Only register the handler for
audio1 on the 1788.
* Since the input sides are actually the same, GC the duplicated code.
* Re-KNF in a bunch of places.
* Make this work again on the 1887 in the Shark.
from the tsleep()'s (they probably shouldn't have been there in the
first place!). Making parity re-writing and copybacks interruptable
will require re-designing how a few things are done (e.g. how memory
is freed for structures shipped off to routines that run asynchronously
relative to the calling routine). Fix a few other tsleep's while we're at it.
autoconfiguration time; this can be done better from rc.local.
(For INSTALL kernels, WSDISPLAY_DEFAULTSCREENS can be defined which
sets up that many screens with default parameters.)
DRIVE_OLD, DRIVE_ATA or DRIVE_ATAPI based on register signatures.
The attach routine will issue a IDENTIFY command for ATA/ATAPI disk,
to detect flase matches by the probe routine.
probe/attach should now be fully compliant with ata-4/ata-5. As a side
effect, ATAPI drives which improperly use ATA register signatures should now
be attached as ATAPI.
support a little: clean-bits now also get frobbed on partition
opening/closing, rather than just at device configuration and device
unconfiguration. Schedule shutdownhooks() stuff for nukage at a later
date, since it isn't really necessary any more.
need to downgrade, downgrade to PIO, as it has been shown if we got CRC errors
in Ultra-DMA mode, we will have silent data corruption in multiword DMA mode
(isn't IDE wonderfull ? :).
Set timeout to 1s for "normal" ata I/O, to minimise the effects of missed
interrupts.
(1) remove unused and probably bad (from an API POV) ioctls,
(2) split tyfl into type and flags,
(3) collect an array of samples, and add them all at once. Soon, this
will be using gzip to estimate the entropy, but for now the original
estimation methods are still used.
(4) kill rnd_add_data() -- it compliated the API for little benefit
This is a workaround for crappy hardware, normal keyboard controllers
return a "0".
Should fix PR port-i386/6636 by Krister Walfridsson and problems
reported by chopps and fvdl.
mjacob