(e.g. from 0x3bc to 0x3bf, for example). Others may require more,
but until there's some special handling for them, 4 should be returned
so that on systems with I/O port accounting, the unit at 0x3bf can be
properly mapped, etc. (OK'd by mycroft.)
that their child busses can be attached after the PCI bus
autoconfiguration for their parent bus is done.
This works because:
(1) there can be at most one ISA/EISA bridge per PCI bus, and
(2) any ISA/EISA bridges must be attached to primary PCI
busses (i.e. bus zero).
That boils down to: there can only be one of these outstanding
at a time, it is cleared when configuring PCI bus 0 before any
subdevices have been found, and it is run after all subdevices
of PCI bus 0 have been found.
This (or something like it) is needed because there are some (legacy)
PCI devices which can show up as ISA/EISA devices as well (the prime
example of which are VGA controllers). If you attach ISA from a
PCI-ISA/EISA bridge, and the bridge is seen before the video board is,
the board can show up as an ISA device, and that can (bogusly)
complicate the PCI device's attach code, or make the PCI device not be
properly attached at all.
This could be done with machine-dependent code, but as more ports
add support for PCI (and PCI-ISA/EISA bridges) more will need it.
The i386 port could (perhaps should) be converted to use it as well.
devices actually do make sense on indirect-config busses, because you
might be able to have more than one of the busses! In addition, they're
useful because they don't require unit numbers to be wired down, so you
could e.g. have vga* at indirect? and vga* at direct?, and have the first
one found be unit number zero. Finally, devices which can divine their
own ports numbers, etc., actually should be cloning, even if you know you'll
only have one bus that they can live on.
1. fix possible hang in en_txlaunch(). when attempting to extend
the length of an mbuf to avoid a flush we should extend it
by cnt [which is ((need - len) % 4)] rather than 4 - cnt.
also, add an EN_DEBUG printf() when we pad/FLUSH a buffer
to help with debugging/understanding what the driver is up to.
2. use interface packet counters
3. when turning off a recv VCI we recompute the new mode. make sure
we don't include the "in service" bit in the new mode, otherwise
a VCI may appear "hung" if you turn it off while a service
interrupt is pending.
4. when shutting down a VCI that is still receiving data, don't bother
going into "drain mode" if only the hardware in service bit is
set (otherwise the VCI may get "hung" in drain mode).
as a result of this we may get "unexpected rx interrupt" messages
which are not really an error, so put this printf in EN_DEBUG.
5. be sure to zero txspeed[lcv] when enabling a VCI (start at full
speed). (hooks for setting txspeed[] are currently not in
the driver, but we are playing with it locally).
credits:
#1: Detected by: Zdenek Salvet <salvet@horn.ics.muni.cz>, fix by me.
#2: Contributed by: Zdenek Salvet <salvet@horn.ics.muni.cz>
#3,#4,#5: Detected by: Milind M. Buddhikot <milind@dworkin.wustl.edu>,
fixed by me.
2841, plus some fixes to make the patches work on the Alpha. Seems to
improve the NCR driver a lot. We probably should try to incorporate
any updates that have happened since, too.
* Add a slot in the softc, ep_pktlenshift, to indicate that
a board implements ``large packets'' (FDDI-sized frames) and
therefore implicitly shifts the argument to packet-length commands
by two bits to fit a 13-bit length in an 11-bit command argument field.
* Change the reset of station-mask filterto be independent of bus-type
(e.g.,. for 3c515)
* Replace the "2044" constant used to disable TX threshold interrupts
on 3c509-generation cards with a #define. Use 2047 instead,
since that works on the large-packet cards (Vortex, Demon, Boomerang)
and 2044 doesn't.
* Add code to epconfing to probe for large-packet support,
set the softc appropriately, and shift packet sizes in commands
by ep_pktlenshift to compensate for the implicit shift.
* Tweak the epconfig() code to avoid hanging on startup.
Set the Tx threshold to interrupt when there's space for
a maximal-sized ether frame, then do epinit() then epstop(),
instead of just the Tx and Rx reset. Required on at least a 3c595.
Tested on a 3c595, but not on 3c509-generation hardware.
(This fixes problems with the printf format fixes i checked in yesterday.
ptrdiff_t is an 'int' on the i386 but a 'long' on the alpha, so the cast
really is necessary... *sigh*)
ISA-compatible port space of PCI buslogic cards.
* Add call to bha_pci.c to disable the ISA-compatible ports of a PCI
device. The ISA-compatible ports are enabled by default, which
causes the card to be autoconfigured a second time as an ISA device,
which appears to deadlock the card.
* Change bha_cmd() to return the number of bytes it actually received
in response to a command, or -1 on error.
* Use heuristics (checking for bha-only registers, and checking the size
of the response to BHA_INQURE_EXTENDED) to bha_find, to make sure the
bha driver never matches an aha (Adaptec 1542 or compatible) device.
A single kernel should now boot on either Adaptec or BusLogic controllers,
provided we always probe for BusLogic devices before Adaptec devices,
but this has not yet been verified.
management by itself. But when it gets a start unit request, it keeps
the floppy motor running all the time. This adds code for dealing with
yet another quirk (SDEV_NOSTARTUNIT) that prevents sd.c from sending
start unit requests. A entry for the Teac FC-1 is added to the quirk
table.
- No more distinction between i/o-mapped and memory-mapped
devices. It's all "bus space" now, and space tags
differentiate the space with finer grain than the
bus chipset tag.
- Add memory barrier methods.
- Implement space alloc/free methods.
- Implement region read/write methods (like memcpy to/from
bus space).
This interface provides a better abstraction for dealing with
machine-independent chipset drivers.
- No more distinction between i/o-mapped and memory-mapped
devices. It's all "bus space" now, and space tags
differentiate the space with finer grain than the
bus chipset tag.
- Add memory barrier methods.
- Implement space alloc/free methods.
- Implement region read/write methods (like memcpy to/from
bus space).
This interface provides a better abstraction for dealing with
machine-independent chipset drivers.
- No more distinction between i/o-mapped and memory-mapped
devices. It's all "bus space" now, and space tags
differentiate the space with finer grain than the
bus chipset tag.
- Add memory barrier methods.
- Implement space alloc/free methods.
- Implement region read/write methods (like memcpy to/from
bus space).
This interface provides a better abstraction for dealing with
machine-independent chipset drivers.
prototypes, and suppress a bogus "might be used uninitialized" warning.
It's clear from reading the logic of the function that produces the
warning that the variable will not be used uninitialized, but the
compiler just isn't smart enough, I guess. Marked XXX for future reference.
restart if we get multiple status interrupts before the softintr()
routine gets a chance to run. The fix is to determine and accumulate
status line changes at the H/W interrupt level, and then check and zero
the accumulated changes when the softint() finally runs. Many thanks
to Bill Studenmund <wrstuden@loki.stanford.edu> for finding and fixing.
thorpej