7b516b31bd
Major overhaul of the Rhine/Rhine-II driver, structuring it a little more
...
like the SMC83C100 EPIC/100 driver:
* Rather than using pointers to the head and tail of the transmit and
receive rings, use wrapping indexes into arrays. This is a little more
obvious when reading the code.
* More cleanly separate the hardware descriptor from the software descriptor.
* bus_dma it everywhere.
* Implement interrupt pacing and avoid a potential race in the transmit
loop.
Now this looks more or less like the Rhine driver I was working on when
this driver was committed :-) Update copyright notice to reflect that.
1999-02-12 00:36:48 +00:00
0b4e481612
add "mii" to vr driver.
1999-02-09 02:04:36 +00:00
c47d6855db
clean up pci configuration a bit
1999-02-09 00:35:35 +00:00
6b77f11d67
put in better name/description for Simon G's board
1999-02-06 06:55:15 +00:00
04046c6dd7
add code to cope with multiple ports per BAR, as are found, for instance,
...
on the 8 port card Simon Gerraty has. In general, cards which have
this lots of ports also have a separate interrupt status register, but
this change is just to talk to the various ports independently. It works,
but it's not optimal. (XXX still need a good name for the card in the
comments, and to update the manual page.)
1999-02-06 06:29:54 +00:00
23382bdfcb
Regen.
1999-02-05 22:55:40 +00:00
0955479f29
Add some Olicom Ethernet device IDs, from FreeBSD's tl driver.
1999-02-05 22:55:19 +00:00
d95d5b1488
Make this driver work on the Alpha. Apparently the receive DMA mechanism
...
has the same 4-byte alignment requirement that the transmit side does. This
causes the packet payload to be misaligned. So, on systems which require
strict alignment, we must copy the incoming frame to a new packet buffer,
suitably aligned.
1999-02-05 22:09:46 +00:00
b52d1e44d0
Fix the interrupt handler to actually acknowledge the interupt to the
...
dispatch code (!!!). How did this work even on the i386 before?
1999-02-05 21:20:31 +00:00
dde3694c4c
Fix some formatting nits.
1999-02-05 08:42:03 +00:00
82a54250be
Remove some duplicate softc members, and comment some of the softc
...
fields.
1999-02-05 08:27:46 +00:00
8bf66d3eb2
Remove some unnecessary splnet's.
1999-02-05 08:21:31 +00:00
50faf19d7d
splimp -> splnet
1999-02-05 07:53:24 +00:00
adc9c40688
Use the generic MII support code, not our own.
1999-02-05 02:58:38 +00:00
ebf3a97519
Use MII command opcodes from <sys/dev/mii.h>
1999-02-05 01:17:24 +00:00
909b90d2d4
Rename VR_MIICMD_DATAIN and VR_MIICMD_DATAOUT to actually match what the
...
data sheet says. (The names and their usage were exactly reversed in the
code.)
1999-02-05 01:10:30 +00:00
5888b4354e
channel_map is called before setup_chip, so whe need to enable the channel
...
status bits in acer_channel_map().
1999-02-02 17:06:05 +00:00
ca240ca7b5
Support for Acerlab M5229 IDE controller. Thanks to Thilo Manske for testing
...
the code, and to Takahiro Kambe who run several tests and finally found the
bug by himself :)
1999-02-02 16:13:59 +00:00
05cbb33e4c
Use pcidevs.h to get vendor and product IDs.
1999-02-02 00:32:21 +00:00
b6a84f08e8
Take software-only structure definitions out of the register description
...
header.
1999-02-02 00:29:17 +00:00
bb5edf7345
Remove support for FreeBSD from the driver; so many changes are going
...
to be required to make it properly portable to all of NetBSD's platforms,
that it just wouldn't be worth the effort.
1999-02-02 00:05:02 +00:00
2bdfbafc37
Minimal changes to make this compile on the Alpha. Much more work is
...
needed to make this a truly portable driver.
1999-02-01 23:40:22 +00:00
1ece20c808
roll internal release tag
1999-01-30 07:08:04 +00:00
d6c1a3e198
Regen.
1999-01-28 04:34:31 +00:00
864e74c18d
Add S3 86C365 Trio3D.
1999-01-28 04:31:33 +00:00
fd094d79ee
NetBSD RCS id.
1999-01-26 06:31:28 +00:00
57d82cd1f3
Change bootverbose 1 to 0.
...
Add vr_lookup.
1999-01-22 05:34:36 +00:00
02bb7a4233
Add VIA Rhine/Rhine II Fast Ethernet files.
1999-01-21 12:02:00 +00:00
4f99746d57
Add NetBSD autoconfiguration support.
...
KNF.
1999-01-21 12:00:25 +00:00
bea8f807a7
Import FreeBSD's VIA Rhine fast ethernet PCI NIC driver
...
written by Bill Paul <wpaul@ctr.columbia.edu>.
1999-01-21 11:55:22 +00:00
76db984c6d
regen
1999-01-16 11:28:19 +00:00
1587097426
add another NCR chip, from Dave Sainty <dave@dtsp.co.nz> per PR kern/6819
1999-01-16 11:27:40 +00:00
edd69ba694
Because memory mapped access doesn't fail only with the docking station
...
for the TI TravelMate 5000 but also with at least one Compaq NIC we
prefer I/O mapped access again. Fixes PR kern/6690.
1999-01-11 22:45:41 +00:00
67e9d2a3bf
Fix a few glitches in the nwscons tga driver, PR #6655 , Brett Slager.
1999-01-11 22:11:36 +00:00
1eba733d91
remove dummy "load_font" entries
1999-01-11 21:35:54 +00:00
4401c8bdd7
oops. Forgot to turn on PCI burst.
1999-01-10 03:41:47 +00:00
c35b8b591b
One more cosmetic change, from Izumi Tsutsui.
1999-01-08 19:55:17 +00:00
0d32a9a78b
Fix more `void *' arithmetic.
1999-01-08 19:22:34 +00:00
3dc31bab2f
Device declaration for the PCscsi-PCI SCSI chip driver.
1999-01-06 23:25:53 +00:00
671d0ae88d
Device driver for the AMD Am53c974 PCscsi-PCI SCSI chip (i.e. the chip used
...
on the Tekram DC-390 SCSI cards), from Izumi Tsutsui, PR#6654. Minor
cosmetic changes by me.
1999-01-06 23:23:33 +00:00
446f262aa5
Regen
1998-12-30 13:50:42 +00:00
4d3847e0ea
Add NeoMagic MagicGraph 128ZV graphic chip.
1998-12-30 13:49:49 +00:00
8ac99457db
I mean *really* clean up headers
1998-12-28 19:12:04 +00:00
b51e3fbf3c
clean up headers; remove early revision 2100 workarounds
1998-12-28 19:11:32 +00:00
da39a16267
Fold lines to 80 chars.
1998-12-27 13:03:58 +00:00
71fa656b19
use a symbolic definition for the PCI subsystem ID
1998-12-21 20:56:06 +00:00
c896b644ba
use a symbolic definition for the PCI subsystem ID
1998-12-21 20:40:01 +00:00
ac7ba300c0
add two of the newer register definitions
1998-12-21 20:31:54 +00:00
45b5108fb1
regen
1998-12-21 13:43:11 +00:00
70a2fcddc2
change name of 82443BX according to Intel's data sheet
...
correct "no AGP" case to real topology of the chip
clarification: s/AGP Device/AGP Interface/
1998-12-21 13:37:00 +00:00
788ff053de
Fix up support for PCI attachments of pcic devices on i386 in general,
...
and the Cirrus Logic CL-PD6729 in particular.
From danw@mit.edu in PR port-i386/6436.
1998-12-20 17:53:28 +00:00
2e81b6b5f8
regen
1998-12-20 16:06:25 +00:00
6eb0418fdb
add a Zoran multimedia controller chip
1998-12-20 16:05:32 +00:00
d15dc38fd9
Changes from FreeBSD:
...
Implemented a more sophisticated mechanism for handling transmitter
interrupts which now defers them until the transmit queue if filled
up with completed buffers. This has two advantages: first, it reduces
the number of transmitter interrupts to just 1/120th of the rate
that they occured previously, and two, running down many buffers
at once has much improved cache effects.
Defer rundown (m_freem) of completed transmit buffers for no longer
than 1 second.
This brings us up-to-date with the most recent "fxp" driver in FreeBSD.
1998-12-19 01:14:37 +00:00
30f21adec4
Regen.
1998-12-18 21:08:37 +00:00
6779120f4a
Add product ID for the Yamaha 724 Audio device. PR #6605 , Dave Sainty.
1998-12-18 21:08:19 +00:00
9595b984ec
teach fxp about rnd_*()
1998-12-17 23:25:29 +00:00
2d5b32dd03
fix an invalid panic message.
1998-12-17 17:45:08 +00:00
f1addbd3fd
Defer mapping of pci interrupt to pciide_mapregs_native(). This way,
...
the native interrupt shouldn't be mapped if a channel is in native mode,
but disabled.
1998-12-16 13:21:26 +00:00
2093338697
Rearange the modes setup to allow these to be dyanmically changed. Fill
...
in the new "set_mode" callback.
1998-12-16 12:48:45 +00:00
b33907f299
Don't DMA the scsi command from or the sense data to the scsipi_xfer
...
directly. That would require that we map the scsipi_xfer into DMA
space. Instead, copy to/from the NCR CCB, which the script already
has to DMA to/from. These copies are small, and don't seem to affect
performance.
1998-12-13 00:11:37 +00:00
178fc3cc05
Step 3:
...
Use DMA maps for the actual data transfers.
1998-12-12 23:41:56 +00:00
3cc30b3641
Step two:
...
Use DMA-safe memory for the script instances. The most important thing
here is that is guarantees that the script is contiguous in DMA space.
1998-12-12 00:19:13 +00:00
086b4b0bf1
Step one of bus_dma'ing the PCI NCR driver:
...
Separate the ncb (i.e. softc) members that are accessed by the script into
a separate structure. Allocate one of these structures in DMA safe memory
using bus_dma, and change RELOC_SOFTC to use the DMA address of this
structure.
1998-12-11 23:21:11 +00:00
b94cb7b768
Add a driver for the S3 SonicVibes chip. From OpenBSD and
...
Constantine Paul Sapuntzakis (csapuntz@cvs.openbsd.org ) with
some changes by me.
XXX The driver still needs work.
1998-12-10 18:47:18 +00:00
93e17878d1
Regen.
1998-12-09 23:57:58 +00:00
02d7f1236c
Some more touchup on the VIA Rhine chip model number, and so some
...
sorting.
1998-12-09 23:57:35 +00:00
74bc9f26d5
Update HBAs to incorporate the new max_lun property.
1998-12-05 19:43:33 +00:00
3f225e009d
Add Sigma Designs REALmagic Hollywood Plus MPEG-2 decoder
1998-12-05 19:02:14 +00:00
9175cc0ddf
The chipset manual doesn't tell the truth about the channel enable
...
register bits. Replace by experimental result.
1998-12-04 17:30:55 +00:00
47ab212504
Rename pio_mode, etc ... to PIO_cap, etc ... for consistency with the
...
ata_drive_datas struct. Suggested by Soren S. Jorvan.
1998-12-03 18:24:30 +00:00
334abc06cf
Correct definition for SIS_TIM_UDMA_EN macro. Ultra-DMA should now work ...
1998-12-03 17:29:01 +00:00
e39a5bdc53
Now that vtophy() is no longuer used, re-enable WDCDEBUG, with
...
wdcdebug_pciide_mask = 0 (so that one can easily patch this variable and give
me more informations :)
1998-12-03 17:27:57 +00:00
2b28c858d8
add a udma_mode field to wdc_softc, and use it the same way dma_mode is used
...
(higthest ultra-dma mode supported). There may be a higther ultra-dma mode
defined ...
1998-12-03 15:38:59 +00:00
ba90b4b2d3
Add URLs of documentation source (from Matthias Drochner).
1998-12-03 14:06:16 +00:00
7d87d6a5f6
Use correct register when disabling the second channel.
1998-12-03 13:50:38 +00:00
8ef785add8
Restore changes from revision 1.17:
...
"If a channel has no drives, do *not* unmap its I/O regions.
It's not really safe to use them for anything else, and in legacy mode it
will just cause us to probe the channel again as an ISA device."
1998-12-03 13:30:00 +00:00
1af63c0605
Correct a few bogons in the SiS chip initialisation.
1998-12-03 13:25:44 +00:00
09408781c9
Ouh ! Correct the 8-bit PCI registers reading/writing functions: need to
...
multiply the register offset by 8.
1998-12-03 13:24:11 +00:00
45675ab14b
- change drive_flags from u_int8_t to u_int16_t
...
- keep the modes supported by the drive in struct ata_drive_datas (will be
later used for downgrading the DMA/PIO mode on error)
- use config flags to force/disable PIO/DMA/UDMA modes
- For the CMD PCI0643/6 setup DMA mode to DMA Read multiple.
1998-12-02 10:52:24 +00:00
aeec8f4cb2
regen
1998-11-30 19:47:53 +00:00
cef29c6e94
Per PR/6172 (Johnny Lam, lamj@stat.cmu.edu), fix pcidevs identification
...
of CL-PD6729. See <http://www.cirrus.com/products/overviews/pd6729.html >.
1998-11-30 19:47:16 +00:00
2407a4bd22
Regen.
1998-11-29 02:00:33 +00:00
feb6a5652f
Fix the original Rhine's part number (thanks to Greg Oster).
1998-11-29 02:00:13 +00:00
17ac4ec4c5
Regen.
1998-11-29 01:54:16 +00:00
f051479ec7
Garbage-collect some bogus RealTek entries.
1998-11-29 01:54:02 +00:00
ecaece3f26
Add product IDs for the VIA Rhine and Rhine-II 10/100 Ethernet chips.
...
(XXX What is the original Rhine's part number?!)
1998-11-29 01:53:33 +00:00
b0bb754f03
regen
1998-11-27 10:43:52 +00:00
d5a92a68de
add Powerstorm 4D50T graphics found in some Alphas
1998-11-27 10:39:16 +00:00
dcfd79f257
regenerated pcidevs.h and pcidevs_data.h due to kern/6280
...
(not kern/5847 as originally noted)
1998-11-26 20:05:38 +00:00
ca707fcdf2
Make the copyright header conform to the NetBSD template.
1998-11-25 22:32:04 +00:00
9726cfd1fb
Make the copyright header conform to the NetBSD template.
1998-11-25 22:17:06 +00:00
cc6a0ef02b
Use bus_dma(9) for the DMA ops in fxp_init() too. Without this the driver
...
was stuck in the while (!(cbp->cb_status & FXP_CB_STATUS_C)); loop,
I think because the relevent CPU cache entry was never updated.
This was on a compaq deskpro system.
1998-11-25 17:19:09 +00:00
5888c5ef44
a small optimization for the compat interrupt handling, possible after
...
channel_softc is within pciide_channel
1998-11-24 19:54:20 +00:00
4cb534cca1
added 82443BX_AGP_NOT as per kern/5847
1998-11-23 22:54:02 +00:00
152d52c171
headers for new hardware support in pciide.c. from Manuel.
1998-11-21 16:06:45 +00:00
9effbbe436
some restructuring, more or less to get support for weird IDE controllers,
...
eg the Cypress ISA bridge:
-put channel mapping into the chip specific part, unify with
channel_probe() into channel_map()
-use pointer to channel data as function call argument wherever possible
instead of the channel number
-allow the "compat" channel number to differ from the per-controller
channel number - for mapping and interrupt functions
-add support for SiS5598 and Cypress 82C693 chips
Mostly done by Manuel, I only contributed to the first 2 items.
1998-11-21 15:55:31 +00:00
3b068a6c78
Adapt to the new scsipi_adapter interface.
1998-11-19 21:53:32 +00:00
db3051d720
fix problems in many d_mmap routines:
...
- returned EOPNOTSUPP rather than -1.
- no check for negative offset.
many of these fix potential security problems in these drivers.
XXX XXX XXX
the d_mmap cdev routine should be changed to have a prototype like:
paddr_t (*d_mmap) __P((dev_t, off_t, int));
by someone!
1998-11-19 15:38:20 +00:00
cb703f0332
If a channel has no drives, do *not* unmap its I/O regions.
...
It's not really safe to use them for anything else, and in legacy mode it
will just cause us to probe the channel again as an ISA device.
1998-11-17 17:59:14 +00:00
56107b8e10
Force PCI_COMMAND_MASTER_ENABLE if DMA has been setup properly. The BIOS is
...
supposed to do it but who knows ...
1998-11-12 15:05:29 +00:00
1e71e76d6c
- clearify the boot messages (features supported vs features used). Thanks to
...
Havard Eidnes for his complains about this :)
- fix some typo in comments
- hoppefully better detection of drives reporting bogus PIO modes.
1998-11-11 19:38:27 +00:00
1a5d2ce537
File is obsolete.
1998-11-10 05:56:31 +00:00
1b8620b9fb
Cleanup media set on Alpha. ring txpoll after setting proper tx
...
interrupt mask.
1998-11-09 23:41:14 +00:00
a1b2be7e1d
Const poisoning.
1998-11-09 23:12:48 +00:00
9f20ff377a
Make the device lookup table-driven, like if_ep_pci.c.
1998-11-09 23:12:18 +00:00
432a301fc6
Support for the CMD PCI064{3,6}. Tested on a 0646 with a
...
"wd0: PIO mode 4, DMA mode 2, UDMA mode 2" device.
1998-11-09 09:21:09 +00:00
d878e9efc8
Rely on priority match to resolve conflict with the ex driver, not on
...
a define.
1998-11-07 23:06:26 +00:00
f213d2f96a
use common code for extended capability (power management)
...
let "match" return 2 (> ep_pci)
1998-11-07 16:53:19 +00:00
bbe9d71415
add support for "extended capabilities" (new in PCI spec 2.2)
1998-11-07 16:47:22 +00:00
7b10c3e7e4
Add the 'ex' driver, a DMA driver for 3Com 90x and 90xB cards. Rename
...
constants from EP_ to ELINK_ since they're now used in the ex driver as well.
1998-11-04 00:29:28 +00:00
7fe67ebc21
Add support for the Seeq 80c24 AutoDUPLEX media interface which was nuked
...
when this driver was changed to use the MAC-independent MII code. This
"PHY" does not have a programming interface, but simply senses the duplex
mode from the link partner. Since it is not possible to read the 80c24
to determine the link type or status, we consider this to be "manual".
1998-11-03 05:47:38 +00:00
cbcaaa3bc3
Make sure that a delay loop actually has some delay in it, and use IFF_OACTIVE
...
as appropriate.
1998-11-03 05:04:49 +00:00
7d4ee06d3e
Use the rtl80x9 common code for media selection.
1998-10-31 00:45:48 +00:00
992f2906ba
Move the RTL8029 register definitions to <dev/ic/rtl80x9reg.h>, and add
...
the registers/bits present in the RTL8019 (ISA version).
1998-10-31 00:27:41 +00:00
de14bf4f80
Manuel confirms that defaulting to AUTO is ok, to Do It.
1998-10-30 23:30:16 +00:00
04c995f517
Add support for media selection to the PCI front-end of the NE2000
...
driver. Currently supports:
RealTek 8029: 10base2, 10baseT, 10baseT-FDX, auto detect (but not FDX).
1998-10-28 00:15:54 +00:00
a45667c4c3
Add register definitions for PCI NE2000-compatible extenstions, allowing
...
control over e.g. full-duplex mode, media, etc.
Currently, only extensions for the RealTek 8029 are defined.
1998-10-27 22:30:56 +00:00
e5c050d79c
Cosmetic changes in product lookup, to match other drivers.
1998-10-27 19:49:37 +00:00
31dec5ddc5
Add config flags for pciide: 0x001 forces the use of DMA when the driver
...
don't know how to set the controller's modes.
1998-10-22 15:11:39 +00:00
1456b01d77
Fix for Apollo DMA mode (not UDMA): DMA mode = PIO mode - 2, not PIO mode + 2 !
1998-10-20 18:47:45 +00:00
167e694c99
Regen.
1998-10-20 01:39:41 +00:00
1715793000
Add RealTek 8129 and 8139 10/100Mb Ethernet IDs.
1998-10-20 01:38:57 +00:00
f69c40b8be
Fix a memory leak in fxp_stop(), from the FreeBSD driver.
1998-10-19 23:51:15 +00:00
22acea3cb7
Fix a comment.
1998-10-19 12:26:22 +00:00
c90c4b829b
Add support for the second flavour of the VIA IDE chip (which has UDMA).
...
Don't claim DMA support if we don't have explicit support for this chip.
They're to may way to loose when trying to use DMA without configuring the
controller and disks.
1998-10-19 12:24:33 +00:00
04bdcc421c
Regen.
1998-10-19 12:13:57 +00:00
682ee5fdf3
Yet another attemp at getting the VIA tech. product name/ID's rigth.
...
It seems that different products have the same name (sigh).
1998-10-19 12:11:50 +00:00
da5d0a6f17
pciide.c: don't define WDCDEBUG, so it compiles on alpha. Correct a bogon
...
in the printing of DMA mode (piix3/4 only)
others: set the debug_mask to 0, so that debug messages are turned off by
default but can be easily turned on.
Reset drive_flags to 0 for unconfigured devices, so that they are ignored
later. For configured devices, reset state to 0 after probe/attach.
1998-10-13 08:59:45 +00:00
19fddaeeb5
Merge bouyer-ide
1998-10-12 16:09:10 +00:00
29d472f53d
Garbage-collect the open_target_lu and close_target_lu entry points from
...
struct scsipi_adapter; they were not used.
Add a scsipi_ioctl entry point to struct scsipi_adapter. This will be
used to issue ioctl commands to the host adapters.
Inspired by PR #6090 , from Matt Jacob.
1998-10-10 00:28:28 +00:00
29c8a3aa85
Regen.
1998-10-05 20:38:17 +00:00
1469dc411b
Correct vendor 0x1191 to "ACARD", add missing Matrox boards.
...
Fixes PR kern/6251 by Soren S. Jorvang.
1998-10-05 20:34:39 +00:00
2aac65de87
Regen.
1998-10-04 23:52:43 +00:00
a6a06368ce
Add S3 Virge/DX, fixes PR kern/6245 by Steve Allen.
1998-10-04 23:50:05 +00:00
b28935cee3
Add missing field to le_softc structure, missed in previous commit. Name
...
it consistently with the other fields.
1998-10-02 00:20:52 +00:00
5dbf12a22a
Regen.
1998-10-01 23:33:25 +00:00
b7957e0200
Fix typo in 905BT4 product name.
1998-10-01 23:32:41 +00:00
a81796636f
support media selection / full duplex
1998-10-01 20:39:01 +00:00
6e32aa4af4
Invert the RXCOPY test. Note that most new platforms will not
...
have relaxed alignment so the de driver should just work on them.
1998-09-29 22:40:52 +00:00
b2a68e14db
Change sources to be KNF
1998-09-26 19:53:34 +00:00
2cf169c563
Add AdvanSys ULTRA WIDE SCSI controllers
1998-09-26 16:20:31 +00:00
b207a7d09d
Change product ADVSYS 2300 to ADVSYS WIDE
1998-09-26 16:16:23 +00:00
da0a3e615e
Add support for AdvanSys Ultra Wide boards ABP-9xxUW
1998-09-26 16:09:32 +00:00
4372d4402e
Remove Wide boards references
...
Update supported boards list
1998-09-26 15:52:55 +00:00
1131320f18
Fix transmit underflow messages. (\0128 != \0 128)
1998-09-25 18:06:53 +00:00
0c812cb0bc
Regenerate from pcidevs.
1998-09-22 23:00:44 +00:00
de8340f7fd
Add ALI M1531 Host-PCI bridge.
...
Add Cirrus Logic CS4610 and CS4280 Audio chips.
Add Cirrus Logic CS4400 communications controller.
1998-09-22 22:59:02 +00:00
d3e02fc461
Fix the accton support. Only set the board type it isn't an ISV.
1998-09-22 04:23:18 +00:00
07bb8331e8
Roll back to 1.71 version- too many unexplainable problems with 1.72.
1998-09-21 14:53:58 +00:00
thorpej