The isa attachment code is in isa/lpt_isa.c now, which attaches to the
already created ic/lpt* files.
You don't need to change your config files, but you need to re-"config" if
using lpt at isa.
XXX The "lpt" device definition should be in sys/conf/files instead, but to
my knowledge, there are some ports which have private copies of lpt, and would
choke on that. No need to make people unhappy 7 days before release branching.
The following patch employs a smarter adaptive polling
scheme. It also improves the comments, in particular giving
due credit to Phil Budne for his efforts in nunderstanding
the device. It also relaxes the pattern for auto config so
more devices match.
pseudo-device rnd # /dev/random and in-kernel generator
in config files.
o Add declaration to all architectures.
o Clean up copyright message in rnd.c, rnd.h, and rndpool.c to include
that this code is derived in part from Ted Tyso's linux code.
but do not assume any entopy is gathered. It can be enabled using an
IOCTL again if the user desires.
Note that the mix function uses xor, so at worse an attacker can twiddle
bits in the pool, but not into a known state assuming it started as
an unknown.
Over the next few days (thank goodness for long weekends) I'll be hunting
down device drivers and adding hooks to gather entropy from many devices,
and adding the conf.c changes to the various port's device structs to
define major numbers for /dev/random and /dev/urandom.
- dereference a pointer to function explicitly.
- fold long line to fit columns < 80.
- put whitespaces around a binary operator.
- don't put a single statement into a block.
about actual position when reading tape position, you should flush any
pending writes. Well, if the tape is write protected, some drives don't
see the zero count WRITE FILE MARK command as a no-op and complain. Dumb!
Add newer Intel / VIA i386 chipsets.
Correct one S3 chip, add one.
Mostly from Carl Shapiro <css@samsara.dialup.access.net> per PR kern/4169
and kern/4170 (identical).
- Indent with tab of width 8.
- Use four column to indent continuation line.
- Fold long line if possible.
- Use return (xx) instead of return xx.
- Compare pointer against NULL instead of testing like boolean.
- Delete whitespace at the end of line.
- Delete whitespace in front of function call operator.
- Delete whitespace after cast.
- Dereference a pointer to function explicitly.
- Add an empty line after local variable declaration.
- Use NULL instead of (char *)0.
- Dont use block for single statement.
The method for doing this is to try and use the DATA COMPRESSION mode page
first, followed by the DEVICE CONFIGURATION page (this is because most newer
tape devices are now using DATA COMPRESSION instead of DEVICE CONFIGURATION
pages).
Add in the logical && hardware read position and set position ioctls. Oddly
enough, because NetBSD is limited in having the driver track file && record
numbers, the usual agony over what to do once you use logical or hardware
block positioning can be avoided. Amusing.
Make a minor change so that for SCSIVERBOSE cases that SCSI_SILENT in
the xs' flags is still observed.
[1] add EN_ENIDMAFIX - the byte-aligner on the ENI version of the card
appears to lose under heavy load so avoid using it. see comment
in midway.c for full details.
note that the Adaptec version of the card works properly under
load.
detected by Kenjiro Cho <kjc@csl.sony.co.jp> [confirmed by chuck]
fix by chuck & kjc
[2] update some freebsd specific code [from kjc]
[3] for circular buffers: ensure there is always one free slot so
that we can easily tell the difference between a full and
empty list. re-structure a few loops to reflect this.
fixes a problem with mbufs being free'd while still in DMA,
and makes drive a bit more robust.
detected and fixed by kjc
memory-mapped or i/o-mapped access to the device registers, and always
choose memory-mapped if it is enabled. In particular, do _not_ explictly
disable the space we decide to not use, as this confuses some versions
of Alpha console software (which are arguably buggy because of this
problem).
Also, fix a logic error pointed out by Ross Harvey <ross@teraflop.com>
that would cause memory-mapped access to never be enabled.
* support chip clocks != COM_FREQ, by introducing sc_frequency (for the
mainline code) and adding a frequency parameter right after the rate
parameter to comcnattach() and com_kgdb_attach().
- Make com_isa and com_multi initialize sc_frequency to COM_FREQ.
- Make i386/machdep.c and alpha/dec_xxx.c call com*attach() with the freq.
parameter.
* supio_attach_args get two more fields: a sc_ipl and a sc_arg, both ints.
- com_supio uses the first for interupt establishment (all childs will, as
soon as they exist) and the 2nd for sc_frequency.
- drsupio passes sc_ipl alway as 5, and for the "com"s, sc_arg as 16*115200
- hyper will pass sc_ipl as 6, and sc_arg as 16 * 460800
be probed several times. This fixes the "ATAPI CD probed as wd drive" problem.
Thanks to Geoff Wing <mason@primenet.com.au> for testing this on his hardware.
I also made inclusion of LPRINTF() dependent solely on the symbol
LPTDEBUG, initialized lptdebug variable to 0 instead of 1, and
matched arguments to format strings in LPRINTF() calls.
pci_map_mem(), with appropriate changes for bus_space.
* Add extra arguments for use by pci_mapreg_*(), and make the functions
static.
* Rewrite pci_mapreg_info() and pci_mapreg_map() as wrappers around
pci_*_find(), using the documented interface.
Because of the braindead design of the SB the input and output have to
use different precisions (8 and 16 bits). It is possible to set the driver
to use 8 bits on both and it will the emulate 8 bits on the output by
expanding it to 16 bits.
looking what's the autoconfig do on strange harware, and ATAPI_DEBUG2 is
for debuging data transfers (and is really verbose once the machine has booted
from an IDE disk).
thorpej