unicorn/docs/FAQ.md

Why is my execution so slow?

Typically, it’s due to

• Instrumenting every instruction executed.
• Instrumenting every memory access.

Optimize your program with less instrumentation, e.g. by using UC_HOOK_BLOCK instead of UC_HOOK_CODE

Why do I get a wrong PC after emulation stops?

Updating PC is a very large overhead (10x slower in the worst case, see FAQ above) for emulation so the PC sync guarantee is explained below in several cases:

• A UC_HOOK_CODE hook is installed. In this case, the PC is sync-ed everywhere within the effective range of the hook. However, on some architectures, the PC might by sync-ed all the time if the hook is installed in any range. Note using count in uc_emu_start implies installing a UC_HOOK_CODE hook.
• A UC_HOOK_MEM_READ or UC_HOOK_MEM_WRITE hook is installed. In this case, the PC is sync-ed exactly before any read/write events within the effective range of the hook.
• Emulation (uc_emu_start) terminates without any exception. In this case, the PC will point to the next instruction.
• No hook mentioned above is installed and emulation terminates with exceptions. In this case, the PC is sync-ed at the basic block boundary, in other words, the first instruction of the basic block where the exception happens.

Below is an example:

mov x0, #1 <--- the PC will be here
mov x1, #2
ldr x0, [x1] <--- exception here

If ldr x0, [x1] fails with memory exceptions, the PC will be left at the beginning of the basic block, in this case mov x0, #1.

However, if a UC_HOOK_MEM_READ hook is installed, the PC will be sync-ed:

mov x0, #1 
mov x1, #2
ldr x0, [x1] <--- exception here and PC sync-ed here

I get an “Unhandled CPU Exception”, why?

Unicorn is a pure CPU emulator and usually it’s due to no handler registered for instructions like syscall and SVC. If you expect system emulation, you probably would like qiling framework.

I would like to instrument a specific instruction but get a UC_ERR_HOOK, why?

Currently, only a small subset of the instructions can be instrumented.

On x86, all available instructions are: in out syscall sysenter cpuid.

Emulating some instructions gives an error like "Invalid Instruction", what should I do?

1. Some instructions are not enabled by default on some architectures. For example, you have to setup CSR on RISC-V or VFP on ARM before emulating floating-point instructions. Refer to the corresponding manual to check if you leave out possible switches in special registers.
2. Different CPU models support different sets of instructions. This is especially observed on ARM CPUs. For example, for THUMB2 big-endian instructions, consider setting CPU model to cortex-r5 or arm_max. See #1725 and #1724.
3. If you are on ARM, please check whether you are emulating a THUMB instruction. If so, please use UC_MODE_THUMB and make sure the starting address is odd.
4. If it's not the cases above, it might be some newer instruction sets that qemu5 doesn’t support.
5. Note some instruction sets are not implemented by the latest QEMU.

If you are still using Unicorn1, please upgrade to Unicorn2 for better support.

Memory hooks get called multiple times for a single instruction

There are several possibilities, e.g.:

• The instruction might access memory multiple times like rep stos in x86.
• The address to access is bad-aligned and thus the MMU emulation will split the access into several aligned memory access. In worst cases on some arch, it leads to byte by byte access.

I can't recover from unmapped read/write even I return true in the hook, why?

This is a minor change in memory hooks behavior between Unicorn1 and Unicorn2. To gracefully recover from memory read/write error, you have to map the invalid memory before you return true.

It is due to the fact that, if users return true without memory mapping set up correctly, we don't know what to do next. In Unicorn1, the behavior is undefined in this case but in Unicorn2 we would like to force users to set up memory mapping in the hook to continue execution.

See the sample for details.

My emulation gets weird read/write error and CPU exceptions.

For MIPS, you might have an address that falls in MIPS kseg segments. In that case, MMU is bypassed and you have to make sure the corresponding physical memory is mapped. See #217, #1371, #1550.

For ARM, you might have an address that falls in some non-executable segments. For example, for m-class ARM cpu, some memory area is not executable according to the ARM document.

KeyboardInterrupt is not raised during uc.emu_start

This is intended as python signal module states:

A long-running calculation implemented purely in C (such as regular expression matching on a large body of text) may run uninterrupted for an arbitrary amount of time, regardless of any signals received. The Python signal handlers will be called when the calculation finishes.

A workaround is to start emulation in another thread.

Editing an instruction doesn't take effect/Hooks added during emulation are not called.

Unicorn is a fork of QEMU and inherits most QEMU internal mechanisms, one of which is called TB chaining. In short, every block (in most cases, a basic block) is translated, executed and cached. Therefore, any operation on cached addresses won't immediately take effect without a call to uc_ctl_remove_cache. Check a more detailed discussion here: #1561

Note, this doesn't mean you have to care about Self Modifying Code because the read/write happens within emulation (TB execution) and QEMU would handle such special cases. For technical details, refer to the QEMU paper.

TLDR: To ensure any modification to an address will take effect:

1. Call uc_ctl_remove_cache on the target address.
2. Call uc_reg_write to write current PC to the PC register, if the modification happens during emulation. It restarts emulation (but doesn't quit uc_emu_start) on current address to re-translate the block.

How to emulate interrupts (or ticks) with Unicorn?

As stated, Unicorn is a pure CPU emulator. For such emulation, you have two choices:

• Use the timeout parameter of uc_emu_start
• Use the count parameter of uc_emu_start

After emulation stops, you may check anything you feel interested and resume emulation accordingly.

Note that for cortex-m exec_return, Unicorn has a magic software exception with interrupt number 8. You may register a hook to handle that.

Why not keep up the upstream qemu?

To provide end users with simple API, Unicorn does lots of dirty hacks within qemu code which prevents it from sync painlessly.

Is there anyway to disable softmmu to speed up execution?

Yes, it’s possible but that is not Unicorn’s goal and there is no simple switch in qemu to disable softmmu.

I'd like to make contributions, where do I start?

See milestones and coding convention.

Be sure to send pull requests for our dev branch only.

Which qemu version is Unicorn based on?

Prior to 2.0.0, Unicorn is based on qemu 2.2.1. After that, Unicorn is based on qemu 5.0.1.