valgrind pointed out that we call KVM_S390_GET_IRQ_STATE with an
undefined value for flags. Kernels prior to 4.15 did not use that
field, and later kernels ignore it for compatibility reasons, but we
better play safe.
The same is true for SET_IRQ_STATE. We should make sure to not use the
flag field, either.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20171122142627.73170-2-borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Now that do_ats_write() is entirely in control of whether to
generate a 32-bit PAR or a 64-bit PAR, we can make it use the
correct (complicated) condition for doing so.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1512503192-2239-13-git-send-email-peter.maydell@linaro.org
[PMM: Rebased Edgar's patch on top of get_phys_addr() refactoring;
use arm_s1_regime_using_lpae_format() rather than
regime_using_lpae_format() because the latter will assert
if passed ARMMMUIdx_S12NSE0 or ARMMMUIdx_S12NSE1;
updated commit message appropriately]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All of the callers of get_phys_addr() and arm_tlb_fill() now ignore
the FSR values they return, so we can just remove the argument
entirely.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Stefano Stabellini <sstabellini@kernel.org>
Message-id: 1512503192-2239-12-git-send-email-peter.maydell@linaro.org
In do_ats_write(), rather than using the FSR value from get_phys_addr(),
construct the PAR values using the information in the ARMMMUFaultInfo
struct. This allows us to create a PAR of the correct format regardless
of what the translation table format is.
For the moment we leave the condition for "when should this be a
64 bit PAR" as it was previously; this will need to be fixed to
properly support AArch32 Hyp mode.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Stefano Stabellini <sstabellini@kernel.org>
Message-id: 1512503192-2239-11-git-send-email-peter.maydell@linaro.org
Now that ARMMMUFaultInfo is guaranteed to have enough information
to construct a fault status code, we can pass it in to the
deliver_fault() function and let it generate the correct type
of FSR for the destination, rather than relying on the value
provided by get_phys_addr().
I don't think there are any cases the old code was getting
wrong, but this is more obviously correct.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Stefano Stabellini <sstabellini@kernel.org>
Message-id: 1512503192-2239-10-git-send-email-peter.maydell@linaro.org
Make get_phys_addr_pmsav8() return a fault type in the ARMMMUFaultInfo
structure, which we convert to the FSC at the callsite.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Stefano Stabellini <sstabellini@kernel.org>
Message-id: 1512503192-2239-9-git-send-email-peter.maydell@linaro.org
Make get_phys_addr_pmsav7() return a fault type in the ARMMMUFaultInfo
structure, which we convert to the FSC at the callsite.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Stefano Stabellini <sstabellini@kernel.org>
Message-id: 1512503192-2239-8-git-send-email-peter.maydell@linaro.org
Make get_phys_addr_pmsav5() return a fault type in the ARMMMUFaultInfo
structure, which we convert to the FSC at the callsite.
Note that PMSAv5 does not define any guest-visible fault status
register, so the different "fsr" values we were previously
returning are entirely arbitrary. So we can just switch to using
the most appropriae fi->type values without worrying that we
need to special-case FaultInfo->FSC conversion for PMSAv5.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Stefano Stabellini <sstabellini@kernel.org>
Message-id: 1512503192-2239-7-git-send-email-peter.maydell@linaro.org
Make get_phys_addr_v6() return a fault type in the ARMMMUFaultInfo
structure, which we convert to the FSC at the callsite.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Stefano Stabellini <sstabellini@kernel.org>
Message-id: 1512503192-2239-6-git-send-email-peter.maydell@linaro.org
Make get_phys_addr_v6() return a fault type in the ARMMMUFaultInfo
structure, which we convert to the FSC at the callsite.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Stefano Stabellini <sstabellini@kernel.org>
Message-id: 1512503192-2239-5-git-send-email-peter.maydell@linaro.org
Make get_phys_addr_v5() return a fault type in the ARMMMUFaultInfo
structure, which we convert to the FSC at the callsite.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Stefano Stabellini <sstabellini@kernel.org>
Message-id: 1512503192-2239-4-git-send-email-peter.maydell@linaro.org
All the callers of arm_ldq_ptw() and arm_ldl_ptw() ignore the value
that those functions store in the fsr argument on failure: if they
return failure to their callers they will always overwrite the fsr
value with something else.
Remove the argument from these functions and S1_ptw_translate().
This will simplify removing fsr from the calling functions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Stefano Stabellini <sstabellini@kernel.org>
Message-id: 1512503192-2239-3-git-send-email-peter.maydell@linaro.org
Currently get_phys_addr() and its various subfunctions return
a hard-coded fault status register value for translation
failures. This is awkward because FSR values these days may
be either long-descriptor format or short-descriptor format.
Worse, the right FSR type to use doesn't depend only on the
translation table being walked -- some cases, like fault
info reported to AArch32 EL2 for some kinds of ATS operation,
must be in long-descriptor format even if the translation
table being walked was short format. We can't get those cases
right with our current approach.
Provide fields in the ARMMMUFaultInfo struct which allow
get_phys_addr() to provide sufficient information for a caller to
construct an FSR value themselves, and utility functions which do
this for both long and short format FSR values, as a first step in
switching get_phys_addr() and its children to only returning the
failure cause in the ARMMMUFaultInfo struct.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Stefano Stabellini <sstabellini@kernel.org>
Message-id: 1512503192-2239-2-git-send-email-peter.maydell@linaro.org
Implement the TT instruction which queries the security
state and access permissions of a memory location.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1512153879-5291-8-git-send-email-peter.maydell@linaro.org
For the TT instruction we're going to need to do an MPU lookup that
also tells us which MPU region the access hit. This requires us
to do the MPU lookup without first doing the SAU security access
check, so pull the MPU lookup parts of get_phys_addr_pmsav8()
out into their own function.
The TT instruction also needs to know the MPU region number which
the lookup hit, so provide this information to the caller of the
MPU lookup code, even though get_phys_addr_pmsav8() doesn't
need to know it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1512153879-5291-7-git-send-email-peter.maydell@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The TT instruction is going to need to look up the MMU index
for a specified security and privilege state. Refactor the
existing arm_v7m_mmu_idx_for_secstate() into a version that
lets you specify the privilege state and one that uses the
current state of the CPU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1512153879-5291-6-git-send-email-peter.maydell@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
For M profile, we currently have an mmu index MNegPri for
"requested execution priority negative". This fails to
distinguish "requested execution priority negative, privileged"
from "requested execution priority negative, usermode", but
the two can return different results for MPU lookups. Fix this
by splitting MNegPri into MNegPriPriv and MNegPriUser, and
similarly for the Secure equivalent MSNegPri.
This takes us from 6 M profile MMU modes to 8, which means
we need to bump NB_MMU_MODES; this is OK since the point
where we are forced to reduce TLB sizes is 9 MMU modes.
(It would in theory be possible to stick with 6 MMU indexes:
{mpu-disabled,user,privileged} x {secure,nonsecure} since
in the MPU-disabled case the result of an MPU lookup is
always the same for both user and privileged code. However
we would then need to rework the TB flags handling to put
user/priv into the TB flags separately from the mmuidx.
Adding an extra couple of mmu indexes is simpler.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1512153879-5291-5-git-send-email-peter.maydell@linaro.org
When we added the ARMMMUIdx_MSUser MMU index we forgot to
add it to the case statement in regime_is_user(), so we
weren't treating it as unprivileged when doing MPU lookups.
Correct the omission.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1512153879-5291-4-git-send-email-peter.maydell@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
In ARMv7M the CPU ignores explicit writes to CONTROL.SPSEL
in Handler mode. In v8M the behaviour is slightly different:
writes to the bit are permitted but will have no effect.
We've already done the hard work to handle the value in
CONTROL.SPSEL being out of sync with what stack pointer is
actually in use, so all we need to do to fix this last loose
end is to update the condition we use to guard whether we
call write_v7m_control_spsel() on the register write.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1512153879-5291-3-git-send-email-peter.maydell@linaro.org
For v8M it is possible for the CONTROL.SPSEL bit value and the
current stack to be out of sync. This means we need to update
the checks used in reads and writes of the PSP and MSP special
registers to use v7m_using_psp() rather than directly checking
the SPSEL bit in the control register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1512153879-5291-2-git-send-email-peter.maydell@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The refactoring of commit 296e5a0a6c has a nasty bug:
it accidentally dropped the generation of code to raise
the UNDEF exception when disas_thumb2_insn() returns nonzero.
This means that 32-bit Thumb2 instruction patterns that
ought to UNDEF just act like nops instead. This is likely
to break any number of things, including the kernel's "disable
the FPU and use the UNDEF exception to identify when to turn
it back on again" trick.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1513006964-3371-1-git-send-email-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Occasionally in Linux guests on x86_64 we're seeing logs like:
ppc_set_irq: 0x55b4e0d562f0 n_IRQ 8 level 1 => pending 00000100req 00000004
when they should read:
ppc_set_irq: 0x55b4e0d562f0 n_IRQ 8 level 1 => pending 00000100req 00000002
The "00000004" is CPU_INTERRUPT_EXITTB yet the code calls
cpu_interrupt(cs, CPU_INTERRUPT_HARD) ("00000002") in this function
just before the log message. Something is causing the HARD bit setting
to get lost.
The knock on effect of losing that bit is the decrementer timer interrupts
don't get delivered which causes the guest to sit idle in its idle handler
and 'hang'.
The issue occurs due to races from code which sets CPU_INTERRUPT_EXITTB.
Rather than poking directly into cs->interrupt_request, that code needs to:
a) hold BQL
b) use the cpu_interrupt() helper
This patch fixes the call sites to do this, fixing the hang. The calls
are made from a variety of contexts so a helper function is added to handle
the necessary locking. This can likely be improved and optimised in the future
but it ensures the code is correct and doesn't lockup as it stands today.
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The msr invalidation code (commits 993eb and 2360b) inverts all
bits except MSR_TGPR and MSR_HVB. On non PowerPC 601 processors
this leads to incorrect change of excp_prefix in hreg_store_msr()
function. The problem is that new msr value get multiplied by msr_mask
and inverted msr does not, thus values of MSR_EP bit in new msr value
and inverted msr are distinct, so that excp_prefix changes but should
not.
Signed-off-by: Kurban Mallachiev <mallachiev@ispras.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
cpu->compat_pvr is used to store the current compat mode of the cpu.
On the receiving side during incoming migration we check compatibility
with the compat mode by calling ppc_set_compat(). However we fail to set
the compat mode with the hypervisor since the "new" compat mode doesn't
differ from the current (due to a "cpu->compat_pvr != compat_pvr" check).
This means that kvm runs the vcpus without a compat mode, which is the
incorrect behaviour. The implication being that a compatibility mode
will never be in effect after migration.
To fix this so that the compat mode is correctly set with the
hypervisor, store the desired compat mode and reset cpu->compat_pvr to
zero before calling ppc_set_compat().
Fixes: 5dfaa532 ("ppc: fix ppc_set_compat() with KVM PR")
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Migration of a system under stress (for example, with
"stress-ng --numa 2") triggers on the destination
some kernel watchdog messages like:
NMI watchdog: BUG: soft lockup - CPU#0 stuck for 3489660870s!
NMI watchdog: BUG: soft lockup - CPU#1 stuck for 3489660884s!
This problem appears with the changes introduced by
42043e4 spapr: clock should count only if vm is running
I think this commit only triggers the problem.
Kernel computes the soft lockup duration using the
Virtual Timebase register (VTB), not using the Timebase
Register (TBR, the one 42043e4 stops).
It appears VTB is not migrated, so this patch adds it in
the list of the SPRs to migrate, and fixes the problem.
For the migration, I've tested a migration from qemu-2.8.0 and
pseries-2.8.0 to a patched master (qemu-2.11.0-rc1). The received
VTB is 0 (as is it not initialized by qemu-2.8.0), but the value
seems to be ignored by KVM and a non zero VTB is used by the kernel.
I have no explanation for that, but as the original problem appears
only with SMP system under stress I suspect some problems in KVM
(I think because VTB is shared by all threads of a core).
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In do_ats_write(), rather than using extended_addresses_enabled() to
decide whether the value we get back from get_phys_addr() is a 64-bit
format PAR or a 32-bit one, use arm_s1_regime_using_lpae_format().
This is not really the correct answer, because the PAR format
depends on the AT instruction being used, not just on the
translation regime. However getting this correct requires a
significant refactoring, so that get_phys_addr() returns raw
information about the fault which the caller can then assemble
into a suitable FSR/PAR/syndrome for its purposes, rather than
get_phys_addr() returning a pre-formatted FSR.
However this change at least improves the situation by making
the PAR work correctly for address translation operations done
at AArch64 EL2 on the EL2 translation regime. In particular,
this is necessary for Xen to be able to run in our emulation,
so this seems like a safer interim fix given that we are in freeze.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Stefano Stabellini <sstabellini@kernel.org>
Message-id: 1509719814-6191-1-git-send-email-peter.maydell@linaro.org
The CPU ID registers ID_AA64PFR0_EL1, ID_PFR1_EL1 and ID_PFR1
have a field for reporting presence of GICv3 system registers.
We need to report this field correctly in order for Xen to
work as a guest inside QEMU emulation. We mustn't incorrectly
claim the sysregs exist when they don't, though, or Linux will
crash.
Unfortunately the way we've designed the GICv3 emulation in QEMU
puts the system registers as part of the GICv3 device, which
may be created after the CPU proper has been realized. This
means that we don't know at the point when we define the ID
registers what the correct value is. Handle this by switching
them to calling a function at runtime to read the value, where
we can fill in the GIC field appropriately.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Stefano Stabellini <sstabellini@kernel.org>
Message-id: 1510066898-3725-1-git-send-email-peter.maydell@linaro.org
Currently, multi threaded TCG with > 1 VCPU gets stuck during IPL, when
the bios tries to switch to the loaded kernel via DIAG 308.
As run_on_cpu() is used, we run into a deadlock after handling the reset.
We need the iolock (just like KVM).
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20171116170526.12643-4-david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Looks like the last fix + cleanup introduced another bug. (for now Linux
guests don't seem to care) - we store the crs into ars.
Fixes: 947a38bd6f ("s390x/kvm: fix and cleanup storing CPU status")
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20171116170526.12643-2-david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Use of GETPC must be restricted to those functions that are
directly called from TCG generated code.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Fixes: 2399d4e7ce
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We use raw memory primitives along the !parallel_cpus paths in order to
simplify the endianness handling. Because of that, we did not benefit
from the generic changes to cpu_ldst_user_only_template.h.
The simplest fix is to manipulate helper_retaddr here.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Fixes the following warning when compiling with gcc 5.4.0 with -O1
optimizations and --enable-debug:
target/arm/translate-a64.c: In function ‘aarch64_tr_translate_insn’:
target/arm/translate-a64.c:2361:8: error: ‘post_index’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
if (!post_index) {
^
target/arm/translate-a64.c:2307:10: note: ‘post_index’ was declared here
bool post_index;
^
target/arm/translate-a64.c:2386:8: error: ‘writeback’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
if (writeback) {
^
target/arm/translate-a64.c:2308:10: note: ‘writeback’ was declared here
bool writeback;
^
Note that idx comes from selecting 2 bits, and therefore its value
can be at most 3.
Signed-off-by: Emilio G. Cota <cota@braap.org>
Acked-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1510087611-1851-1-git-send-email-cota@braap.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We added the entry to insn-data.def, but failed to update op_risbg
to match. No need to special-case the imask inversion, since that
is already ~0 for RISBG (and now RISBGN).
Fixes: 375ee58bed
Fixes: https://bugs.launchpad.net/qemu/+bug/1701798 (s390x part)
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20171107145546.767-1-richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This feature is present for some targets in the bfd disassembler(s).
Implement it generically for all capstone users.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
While trying to make KVM PR usable again, commit 5dfaa532ae introduced a
regression: the current compat_pvr value is passed to KVM instead of the
new one. This means that we always pass 0 instead of the max-cpu-compat
PVR during the initial machine reset. And at CAS time, we either pass
the PVR from the command line or even don't call kvmppc_set_compat() at
all, ie, the PCR will not be set as expected.
For example if we start a big endian fedora26 guest in power7 compat
mode on a POWER8 host, we get this in the guest:
$ cat /proc/cpuinfo
processor : 0
cpu : POWER7 (architected), altivec supported
clock : 4024.000000MHz
revision : 2.0 (pvr 004d 0200)
timebase : 512000000
platform : pSeries
model : IBM pSeries (emulated by qemu)
machine : CHRP IBM pSeries (emulated by qemu)
MMU : Hash
but the guest can still execute POWER8 instructions, and the following
program succeeds:
int main()
{
asm("vncipher 0,0,0"); // ISA 2.07 instruction
}
Let's pass the new compat_pvr to kvmppc_set_compat() and the program fails
with SIGILL as expected.
Reported-by: Nageswara R Sastry <rnsastry@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In the user-mode-only version of sparc_cpu_handle_mmu_fault(),
we must save the fault address for a data fault into the CPU
state's mmu registers, because the code in linux-user/main.c
expects to find it there in order to populate the si_addr
field of the guest siginfo.
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
For AArch32 LDREXD and STREXD, architecturally the 32-bit word at the
lowest address is always Rt and the one at addr+4 is Rt2, even if the
CPU is big-endian. Our implementation does these with a single
64-bit store, so if we're big-endian then we need to put the two
32-bit halves together in the opposite order to little-endian,
so that they end up in the right places. We were trying to do
this with the gen_aa32_frob64() function, but that is not correct
for the usermode emulator, because there there is a distinction
between "load a 64 bit value" (which does a BE 64-bit access
and doesn't need swapping) and "load two 32 bit values as one
64 bit access" (where we still need to do the swapping, like
system mode BE32).
Fixes: https://bugs.launchpad.net/qemu/+bug/1725267
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1509622400-13351-1-git-send-email-peter.maydell@linaro.org
On a successful address translation instruction, PAR is supposed to
contain cacheability and shareability attributes determined by the
translation. We previously returned 0 for these bits (in line with the
general strategy of ignoring caches and memory attributes), but some
guest OSes may depend on them.
This patch collects the attribute bits in the page-table walk, and
updates PAR with the correct attributes for all LPAE translations.
Short descriptor formats still return 0 for these bits, as in the
prior implementation.
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 20171031223830.4608-1-Andrew.Baumann@microsoft.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
WFI/E are often, but not always, 4 bytes long. When they are, we need to
set ARM_EL_IL_SHIFT in the syndrome register.
Pass the instruction length to HELPER(wfi), use it to decrement pc
appropriately and to pass an is_16bit flag to syn_wfx, which sets
ARM_EL_IL_SHIFT if needed.
Set dc->insn in both arm_tr_translate_insn and thumb_tr_translate_insn.
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Message-id: alpine.DEB.2.10.1710241055160.574@sstabellini-ThinkPad-X260
[PMM: move setting of dc->insn for Thumb so it is correct for 32 bit insns]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- missing \r in the BIOS console output
- CPU type name is now "s390x-cpu"
- fixup for the host-model on z14 and older machine versions
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=ir9v
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/borntraeger/tags/s390x-20171030' into staging
s390x: fixups for 2.11
- missing \r in the BIOS console output
- CPU type name is now "s390x-cpu"
- fixup for the host-model on z14 and older machine versions
# gpg: Signature made Mon 30 Oct 2017 08:34:15 GMT
# gpg: using RSA key 0x117BBC80B5A61C7C
# gpg: Good signature from "Christian Borntraeger (IBM) <borntraeger@de.ibm.com>"
# Primary key fingerprint: F922 9381 A334 08F9 DBAB FBCA 117B BC80 B5A6 1C7C
* remotes/borntraeger/tags/s390x-20171030:
s390-*.img: update s390 bios with latest fixes
s390-ccw: print carriage return with new lines
s390x/kvm: use cpu model for gscb on compat machines
target/s390x: change CPU type name to "s390x-cpu"
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Starting a guest with
<os>
<type arch='s390x' machine='s390-ccw-virtio-2.9'>hvm</type>
</os>
<cpu mode='host-model'/>
on an IBM z14 results in
"qemu-system-s390x: Some features requested in the CPU model are not
available in the configuration: gs"
This is because guarded storage is fenced for compat machines that did
not have guarded storage support. While this prevents future migration
abort (by not starting the guest at all), not being able to start a
"host-model" guest is very much unexpected. As it turns out, even if we
would modify libvirt to not expand the cpu model to contain "gs" for
compat machines, it cannot guarantee that a migration will succeed. For
example if the kernel changes its features (or the user has nested=1 on
one host but not on the other) the migration will fail nevertheless. So
instead of fencing "gs" for machines <= 2.9 lets allow it for all
machine types that support the CPU model. This will make "host-model"
runnable all the time, while relying on the CPU model to reject invalid
migration attempts. We also need to change the migration for guarded
storage.
Additional discussions about host-model are still pending but are out
of scope of this patch.
Suggested-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Cornelia Huck <Cornelia Huck <cohuck@redhat.com>
Acked-by: Halil Pasic <pasic@linux.vnet.ibm.com>
For now, e.g. host-s390-cpu wasn't exposed to the user. cpu-add, -cpu
and the CPU model qmp interfaces didn't care about the actual type,
as that information was hidden.
This changed with CPU hotplug via device_add. Now the type is visible to
the user. Before we get that supported in a stable version, this is our
last chance to change it.
So change it from "s390-cpu" to "s390x-cpu", to match the architecture
name. Example names are then e.g. z14-s390x-cpu or qemu-s390x-cpu.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20171020115803.14093-1-david@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
introduce SPARC_CPU_TYPE_NAME macro and use it to
construct cpu type names.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1507211474-188400-32-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
introduce TRICORE_CPU_TYPE_NAME macro and use it to construct
cpu type names. While at it move cpu type_infos into one
array and register it directly with type_init_from_array()
instead of custom tricore_cpu_register_types()/cpu_register()
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1507211474-188400-30-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
use new UNICORE32_CPU_TYPE_NAME to compose CPU type
name and get rid of intermediate
UniCore32CPUInfo/uc32_cpu_register_types()
which is replaced by static TypeInfo array and
type_init_from_array()
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1507211474-188400-28-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
use new XTENSA_CPU_TYPE_NAME to compose CPU type name
to bring xtensa in line with all other targets that
will similar macro.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1507211474-188400-25-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
the field contains upper-cased cpu model name and is used
for printing supported cpu model names for '-cpu help'.
Considering that cpu model lookup in superh_cpu_class_by_name()
is case-insensitive, we can drop upper-casing when
printing supported cpus list and use cpu type directly
to do the same by cutting out SUPERH_CPU_TYPE_SUFFIX from
typename.
It allows to remove SuperHCPUClass::name, which practically
duplicates names defined by TYPE_SH*_CPU definitions and
simplify sh*_class_init()/SuperHCPUClass a bit.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1507211474-188400-24-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
currently for sh4 cpu_model argument for '-cpu' option
could be either 'cpu model' name or cpu_typename.
however typically '-cpu' takes 'cpu model' name and
cpu type for sh4 target isn't advertised publicly
('-cpu help' prints only 'cpu model' names) so we
shouldn't care about this use case (it's more of a bug).
1. Drop '-cpu cpu_typename' to align with the rest of
targets.
2. Compose searched for typename from cpu model and use
it with object_class_by_name() directly instead of
over-complicated
object_class_get_list()
g_slist_find_custom() + superh_cpu_name_compare()
With #1 droped, #2 could be used for both lookups which
simplifies superh_cpu_class_by_name() quite a bit.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1507211474-188400-23-git-send-email-imammedo@redhat.com>
[ehabkost: Include fixup sent by Igor]
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
introduce SUPERH_CPU_TYPE_NAME macro and use it to construct
cpu type names. While at it move cpu type_infos into one
array and register it directly with type_init_from_array()
instead of custom superh_cpu_register_types()
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1507211474-188400-22-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
use new OPENRISC_CPU_TYPE_NAME to compose CPU type name and get
rid of intermediate OpenRISCCPUInfo/openrisc_cpu_register_types()
which is replaced by static TypeInfo array.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1507211474-188400-18-git-send-email-imammedo@redhat.com>
Acked-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
introduce MOXIE_CPU_TYPE_NAME macro and consistently use it
to construct cpu type names. While at it replace dynamic
cpu type name composition with static data.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1507211474-188400-16-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
It 'works' with default CPU only because of bug in
moxie_cpu_class_by_name() where it treats cpu_model
as type name and default cpu_model also happens to be
type name. But specifying explicitly cpu on CLI,
ex: '-cpu MoxieLite', makes QEMU fail since
moxie_cpu_class_by_name() doesn't traslate cpu_model
to cpu type and fails to find corresponding object class.
Fix moxie_cpu_class_by_name() to do proper
cpu_model -> cpu type
translation and fix default cpu_model to be cpu_model
instead of being typename.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1507211474-188400-15-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
use new M68K_CPU_TYPE_NAME to compose CPU type names
and get rid of intermediate M68kCPUInfo/register_cpu_type()
which is replaced by static TypeInfo array.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <1507211474-188400-12-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
introduce LM32_CPU_TYPE_NAME macro and consistently use it
to construct cpu type names. While at it replace dynamic
cpu type name composition with static data.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Michael Walle <michael@walle.cc>
Message-Id: <1507211474-188400-9-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
replace ambiguous TYPE macro with a new CRIS_CPU_TYPE_NAME
and use it consistently in the code.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1507211474-188400-7-git-send-email-imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Introduce ALPHA_CPU_TYPE_NAME macro to replace rather ununique
TYPE macro that alpha uses. With new macro it will follow
the same naming convention as other targets.
While at it put scattered TypeInfo into one array which places
type desriptions at one place and reduces code a bit.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1507211474-188400-5-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Now that every target is using the disas_set_info hook,
the flags argument is unused. Remove it.
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The Capstone disassembler has its own big-endian fixup.
Doing this twice does not work, of course. Move our current
fixup from target/arm/cpu.c to disas/arm.c.
This makes read_memory_inner_func unused and can be removed.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This is identical for each target. So, move the initialization to
common code. Move the variable itself out of tcg_ctx and name it
cpu_env to minimize changes within targets.
This also means we can remove tcg_global_reg_new_{ptr,i32,i64},
since there are no longer global-register temps created by targets.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Groundwork for supporting multiple TCG contexts.
The core of this patch is this change to tcg/tcg.h:
> -extern TCGContext tcg_ctx;
> +extern TCGContext tcg_init_ctx;
> +extern TCGContext *tcg_ctx;
Note that for now we set *tcg_ctx to whatever TCGContext is passed
to tcg_context_init -- in this case &tcg_init_ctx.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Thereby decoupling the resulting translated code from the current state
of the system.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Thereby decoupling the resulting translated code from the current state
of the system.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Thereby decoupling the resulting translated code from the current state
of the system.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Thereby decoupling the resulting translated code from the current state
of the system.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Thereby decoupling the resulting translated code from the current state
of the system.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Thereby decoupling the resulting translated code from the current state
of the system.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Thereby decoupling the resulting translated code from the current state
of the system.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Convert all existing readers of tb->cflags to tb_cflags, so that we
use atomic_read and therefore avoid undefined behaviour in C11.
Note that the remaining setters/getters of the field are protected
by tb_lock, and therefore do not need conversion.
Luckily all readers access the field via 'tb->cflags' (so no foo.cflags,
bar->cflags in the code base), which makes the conversion easily
scriptable:
FILES=$(git grep 'tb->cflags' target include/exec/gen-icount.h \
accel/tcg/translator.c | cut -f1 -d':' | sort | uniq)
perl -pi -e 's/([^.>])tb->cflags/$1tb_cflags(tb)/g' $FILES
perl -pi -e 's/([a-z->.]*)(->|\.)tb->cflags/tb_cflags($1$2tb)/g' $FILES
Then manually fixed the few errors that checkpatch reported.
Compile-tested for all targets.
Suggested-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Move target cpu tcg initialization to common code,
called from cpu_exec_realizefn.
Acked-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
When we used structures for TCGv_*, we needed a macro in order to
perform a comparison. Now that we use pointers, this is just clutter.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The GET and MAKE functions weren't really specific enough.
We now have a full complement of functions that convert exactly
between temporaries, arguments, tcgv pointers, and indices.
The target/sparc change is also a bug fix, which would have affected
a host that defines TCG_TARGET_HAS_extr[lh]_i64_i32, i.e. MIPS64.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In order to support multicore system we move some of the previously
static state variables into the state of each core.
On the other hand in order to allow timers to be synced between each
code the ttcr (tick timer count register) is moved out of the core.
This is not as per real hardware spec which has a separate timer counter
per core, but it seems the most simple way to keep each clock in sync.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Previously coreid and numcores were hard coded as 0 and 1 respectively
as OpenRISC QEMU did not have multicore support.
Multicore support is now being added so these registers need to have
configured values.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Stafford Horne <shorne@gmail.com>
This is a neat way to implement low address protection, whereby
only the first 512 bytes of the first two pages (each 4096 bytes) of
every address space are protected.
Store a tec of 0 for the access exception, this is what is defined by
Enhanced Suppression on Protection in case of a low address protection
(Bit 61 set to 0, rest undefined).
We have to make sure to to pass the access address, not the masked page
address into mmu_translate*().
Drop the check from testblock. So we can properly test this via
kvm-unit-tests.
This will check every access going through one of the MMUs.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20171016202358.3633-3-david@redhat.com>
[CH: restored error message for access register mode]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Simplify the error handling of the MSCH. Let the code detecting the
condition tell (in a less ambiguous way) how it's to be handled. No
changes in behavior.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20171017140453.51099-8-pasic@linux.vnet.ibm.com>
[CH: fix return code for fctl != 0]
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Simplify the error handling of the HSCH. Let the code detecting the
condition tell (in a less ambiguous way) how it's to be handled. No
changes in behavior.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20171017140453.51099-7-pasic@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Simplify the error handling of the CSCH. Let the code detecting the
condition tell (in a less ambiguous way) how it's to be handled. No
changes in behavior.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20171017140453.51099-6-pasic@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Simplify the error handling of the XSCH. Let the code detecting the
condition tell (in a less ambiguous way) how it's to be handled. No
changes in behavior.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20171017140453.51099-5-pasic@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Simplify the error handling of the SSCH and RSCH handler avoiding
arbitrary and cryptic error codes being used to tell how the instruction
is supposed to end. Let the code detecting the condition tell how it's
to be handled in a less ambiguous way. It's best to handle SSCH and RSCH
in one go as the emulation of the two shares a lot of code.
For passthrough this change isn't pure refactoring, but changes the way
kernel reported EFAULT is handled. After clarifying the kernel interface
we decided that EFAULT shall be mapped to unit exception. Same goes for
unexpected error codes and absence of required ORB flags.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20171017140453.51099-4-pasic@linux.vnet.ibm.com>
Tested-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
[CH: cosmetic changes]
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
s390-virtio-ccw.c is the sole user of s390x_new_cpu(),
so move this helper there.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1508253203-119237-1-git-send-email-imammedo@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
object_new() returns cpu with refcnt == 1 and after realize
refcnt == 2*. s390x_new_cpu() as an owner of the first refcnt
should have released it on exit in both cases (on error and
success) to avoid it leaking. Do so for both cases.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1508247680-98800-2-git-send-email-imammedo@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
When we try to start a CPU with a WAIT PSW, we have to take care that
TCG will actually try to continue executing instructions.
We must therefore really only unhalt the CPU if we don't have a WAIT
PSW. Also document the special order for restart interrupts, which
load a new PSW and change the state to operating.
To keep KVM working, simply don't have a look at the WAIT bit when
loading the PSW. Otherwise the behavior of a restart interrupt when
a CPU stopped would be changed.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-31-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Refactor it to use s390_get_feat_block(). Directly write into the mapped
lowcore with stfl and make sure it is really only compiled if needed.
While at it, add an alignment check for STFLE and avoid
potential_page_fault() by properly restoring the CPU state.
Due to s390_get_feat_block(), we will now also indicate the
"Configuration-z-architectural-mode", which is with new SIGP code the
right thing to do.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-30-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Nothing hindering us anymore from unlocking the restart code (used for
NMI).
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-29-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
As we properly implement it, allow to enable it.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-28-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This effectively enables experimental SMP support. Floating interrupts are
still a mess, so allow it but print a big warning. There also seems
to be a problem with CPU hotplug (after the main loop started).
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-27-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[CH: changed insn-data.def as pointed out by Richard]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Thanks to Aurelien Jarno for doing this in his prototype.
We can flush the whole TLB as this should happen really rarely.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-26-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Implement them like KVM implements/handles them. Both can only be
triggered via SIGP instructions. RESET has (almost) the lowest priority if
the CPU is running, and the highest if the CPU is STOPPED. This is handled
in SIGP code already. On delivery, we only have to care about the
"CPU running" scenario.
STOP is defined to be delivered after all other interrupts have been
delivered. Therefore it has the actual lowest priority.
As both can wake up a CPU if sleeping, indicate them correctly to
external code (e.g. cpu_has_work()).
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-25-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Mostly analogous to the kernel/KVM version (so I assume the checks are
correct :) ). As a preparation for TCG.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-24-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
As preparation for TCG.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-23-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
As preparation for TCG.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-22-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Add it as preparation for TCG. Sensing could later be done completely
lockless.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-21-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Preparation for TCG, for KVM is this is completely handled in the
kernel.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-20-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
For KVM, the KVM module decides when a STOP can be performed (when the
STOP interrupt can be processed). Factor it out so we can use it
later for TCG.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-19-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We want to use the same code base for TCG, so let's cleanly factor it
out.
The sigp mutex is currently not really needed, as everything is
protected by the iothread mutex. But this could change later, so leave
it in place and initialize it properly from common code.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-17-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Preparation for moving it out of kvm.c.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-16-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Called from SIGP code to be factored out, so let's move it. Add a
FIXME for TCG code in the future.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-15-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Factor it out into s390_store_status(), to be used also by TCG later on.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-14-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Preparation for factoring it out into !kvm code.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-13-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
No need to pass kvm_run. Pass parameters alphabetically ordered.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-12-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
KVM handles the wait PSW itself and triggers a WAIT ICPT in case it
really wants to sleep (disabled wait).
This will later allow us to change the order of loading a restart
interrupt and setting a CPU to OPERATING on SIGP RESTART without
changing KVM behavior.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-11-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
If we encounter a WAIT PSW, we have to halt immediately. Using
cpu_loop_exit() at this point feels wrong. Simply leaving
cs->exception_index set doesn't result in an immediate stop.
This is also necessary to properly handle SIGP STOP interrupts later.
The CPU_INTERRUPT_HALT will be processed immediately and properly set
the CPU to halted (also resetting cs->exception_index to EXCP_HLT)
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-10-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This will now also detect crashes under TCG. We can directly use
cpu->env.psw.addr instead of kvm_run, as we do a cpu_synchronize_state().
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-9-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Going to OPERATING here looks wrong. A CPU should even never be
!OPERATING at this point. Unhalting will already be done in
cpu_handle_halt() if there is work, so we can drop this statement
completely.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-8-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Interrupts can't wake such CPUs up. SIGP from other CPUs has to be used
to toggle the state.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-7-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We can now let go of INTERRUPT_EXT. When cr0 changes, we have to
revalidate if we now have a pending external interrupt, just like
when the PSW (or SYSTEM MASK only) changes.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-6-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Currently, enabling/disabling of interrupts is not really supported.
Let's improve interrupt handling code by explicitly checking for
deliverable interrupts only. This is the first step. Checking for
external interrupt subclasses will be done next.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-5-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Preparation for new TCG SIGP code. Especially also prepare for
indicating that another external call is already pending.
Take care of interrupt priority.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-4-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
There are still some leftovers from old virtio interrupts in there.
Most importantly, we don't have to queue service interrupts anymore.
Just like KVM, we can simply multiplex the SCLP service interrupts and
avoid the queue.
Also, now only valid parameters/cpu_addr will be stored on service
interrupts.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-3-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
External interrupts are currently all handled like floating external
interrupts, they are queued. Let's prepare for a split of floating
and local interrupts by turning INTERRUPT_EXT into a mask.
While we can have various floating external interrupts of one kind, there
is usually only one (or a fixed number) of the local external interrupts.
So turn INTERRUPT_EXT into a mask and properly indicate the kind of
external interrupt. Floating interrupts will have to moved out of
one CPU instance later once we have SMP support.
The only floating external interrupts used right now are SERVICE
interrupts, so let's use that name. Following patches will clean up
SERVICE interrupt injection.
This get's rid of the ugly special handling for cpu timer and clock
comparator interrupts. And we really only store the parameters as
defined by the PoP.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-2-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
use generic cpu_model parsing introduced by
(6063d4c0f vl.c: convert cpu_model to cpu type and set of global properties before machine_init())
it allows to:
* replace sPAPRMachineClass::tcg_default_cpu with
MachineClass::default_cpu_type
* drop cpu_parse_cpu_model() from hw/ppc/spapr.c and reuse
one in vl.c
* simplify spapr_get_cpu_core_type() by removing
not needed anymore recurrsion since alias look up
happens earlier at vl.c and spapr_get_cpu_core_type()
works only with resulted from that cpu type.
* spapr no more needs to parse/depend on being phased out
MachineState::cpu_model, all tha parsing done by generic
code and target specific callback.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
[dwg: Correct minor compile error]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
next commit will drop ppc_cpu_lookup_alias() declaration from header
and make it static which will break its last user ppc_cpu_class_by_name()
since ppc_cpu_class_by_name() defined before ppc_cpu_lookup_alias().
To avoid this move ppc_cpu_lookup_alias() right before
ppc_cpu_class_by_name().
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
consolidate 'host' core type registration by moving it from
KVM specific code into spapr_cpu_core.c, similar like it's
done in x86 target.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
replace sPAPRCPUCoreClass::cpu_class with cpu type name
since it were needed just to get that at points it were
accessed.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
there is a dedicated callback CPUClass::parse_features
which purpose is to convert -cpu features into a set of
global properties AND deal with compat/legacy features
that couldn't be directly translated into CPU's properties.
Create ppc variant of it (ppc_cpu_parse_featurestr) and
move 'compat=val' handling from spapr_cpu_core.c into it.
That removes a dependency of board/core code on cpu_model
parsing and would let to reuse common -cpu parsing
introduced by 6063d4c0
Set "max-cpu-compat" property only if it exists, in practice
it should limit 'compat' hack to spapr machine and allow
to avoid including machine/spapr headers in target/ppc/cpu.c
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
For POWER ISA v3.0, the XER bit CA32 needs to be set by the shift
right algebraic instructions whenever the CA bit is to be set. This
change affects the following instructions:
* Shift Right Algebraic Word (sraw[.])
* Shift Right Algebraic Word Immediate (srawi[.])
* Shift Right Algebraic Doubleword (srad[.])
* Shift Right Algebraic Doubleword Immediate (sradi[.])
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
At the moment the only POWER9 model which is listed in qemu is v1.0 (aka
"DD1"). This is a very early (read, buggy) version which will never be
released to the public - it was included in qemu only for the convenience
of those doing bringup on the early silicon. For bonus points, we actually
had its PVR incorrect in the table (0x004e0000 instead of 0x004e0100). We
also never actually implemented the differences in behaviour (read, bugs)
that marked DD1 in qemu.
Now that we know the PVR for the substantially better v2.0 (DD2) chip,
include it and make it the default POWER9 in qemu. For the time being we
leave the DD1 definition in place for the poor souls (read, me) who still
need to work with DD1 hardware.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We don't have any 460 or 460F CPUs in QEMU, so the init functions
are just dead code. Let's simply remove them (translate_init.c
is already big enough without them).
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Besides being more correct, arbitrarily long instruction allow the
generation of a translation block that spans three pages. This
confuses the generator and even allows ring 3 code to poison the
translation block cache and inject code into other processes that are
in guest ring 3.
This is an improved (and more invasive) fix for commit 30663fd ("tcg/i386:
Check the size of instruction being translated", 2017-03-24). In addition
to being more precise (and generating the right exception, which is #GP
rather than #UD), it distinguishes better between page faults and too long
instructions, as shown by this test case:
#include <sys/mman.h>
#include <string.h>
#include <stdio.h>
int main()
{
char *x = mmap(NULL, 8192, PROT_READ|PROT_WRITE|PROT_EXEC,
MAP_PRIVATE|MAP_ANON, -1, 0);
memset(x, 0x66, 4096);
x[4096] = 0x90;
x[4097] = 0xc3;
char *i = x + 4096 - 15;
mprotect(x + 4096, 4096, PROT_READ|PROT_WRITE);
((void(*)(void)) i) ();
}
... which produces a #GP without the mprotect, and a #PF with it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These take care of advancing s->pc, and will provide a unified point
where to check for the 15-byte instruction length limit.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This should be done by all target and, since commit 53f6672bcf
("gen-icount: use tcg_ctx.tcg_env instead of cpu_env", 2017-06-30),
is causing the NIOS2 target to hang.
This is because the test for "should I exit to the main loop"
was being done with the correct offset to the icount decrementer,
but using TCG temporary 0 (the frame pointer) rather than the
env pointer.
Cc: qemu-stable@nongnu.org
Cc: Marek Vasut <marex@denx.de>
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It is used by all PPC targets; we can give the directory its own
Makefile.objs file, and include it directly from target/ppc.
target/s390 can do the same when it starts using it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The real kernel has TASK_SIZE as 0x7c000000, due to quirks with
a couple of SH parts. But nominally user-space is limited to 2GB.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20170708025030.15845-4-rth@twiddle.net>
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
We had a check using TARGET_VIRT_ADDR_SPACE_BITS to make sure
that the allocation coming in from the command-line option was
not too large, but that didn't include target-specific knowledge
about other restrictions on user-space.
Remove several target-specific hacks in linux-user/main.c.
For MIPS and Nios, we can replace them with proper adjustments
to the respective target's TARGET_VIRT_ADDR_SPACE_BITS definition.
For ARM, we had no existing ifdef but I suspect that the current
default value of 0xf7000000 was chosen with this in mind. Define
a workable value in linux-user/arm/, and also document why the
special case is required.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20170708025030.15845-3-rth@twiddle.net>
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
The common situation of the SG instruction is that it is
executed from S&NSC memory by a CPU in NS state. That case
is handled by v7m_handle_execute_nsc(). However the instruction
also has defined behaviour in a couple of other cases:
* SG instruction in NS memory (behaves as a NOP)
* SG in S memory but CPU already secure (clears IT bits and
does nothing else)
* SG instruction in v8M without Security Extension (NOP)
These can be implemented in translate.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1507556919-24992-10-git-send-email-peter.maydell@linaro.org
A few Thumb instructions are always unconditional even inside an
IT block (as opposed to being UNPREDICTABLE if used inside an
IT block): BKPT, the v8M SG instruction, and the A profile
HLT (debug halt) instruction.
This means we need to suppress the jump-over-instruction-on-condfail
code generation (though the IT state still advances as usual and
subsequent insns in the IT block may be conditional).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1507556919-24992-9-git-send-email-peter.maydell@linaro.org
Recent changes have left insn_crosses_page() more complicated
than it needed to be:
* it's only called from thumb_tr_translate_insn() so we know
for certain that we're looking at a Thumb insn
* the caller's check for dc->pc >= dc->next_page_start - 3
means that dc->pc can't possibly be 4 aligned, so there's
no need to check that (the check was partly there to ensure
that we didn't treat an ARM insn as Thumb, I think)
* we now have thumb_insn_is_16bit() which lets us do a precise
check of the length of the next insn, rather than opencoding
an inaccurate check
Simplify it down to just loading the first half of the insn
and calling thumb_insn_is_16bit() on it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1507556919-24992-8-git-send-email-peter.maydell@linaro.org
Refactor the Thumb decode to do the loads of the instruction words at
the top level rather than only loading the second half of a 32-bit
Thumb insn in the middle of the decode.
This is simple apart from the awkward case of Thumb1, where the
BL/BLX prefix and suffix instructions live in what in Thumb2 is the
32-bit insn space. To handle these we decode enough to identify
whether we're looking at a prefix/suffix that we handle as a 16 bit
insn, or a prefix that we're going to merge with the following suffix
to consider as a 32 bit insn. The translation of the 16 bit cases
then moves from disas_thumb2_insn() to disas_thumb_insn().
The refactoring has the benefit that we don't need to pass the
CPUARMState* down into the decoder code any more, but the major
reason for doing this is that some Thumb instructions must be always
unconditional regardless of the IT state bits, so we need to know the
whole insn before we emit the "skip this insn if the IT bits and cond
state tell us to" code. (The always unconditional insns are BKPT,
HLT and SG; the last of these is 32 bits.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1507556919-24992-7-git-send-email-peter.maydell@linaro.org
The code which implements the Thumb1 split BL/BLX instructions
is guarded by a check on "not M or THUMB2". All we really need
to check here is "not THUMB2" (and we assume that elsewhere too,
eg in the ARCH(6T2) test that UNDEFs the Thumb2 insns).
This doesn't change behaviour because all M profile cores
have Thumb2 and so ARM_FEATURE_M implies ARM_FEATURE_THUMB2.
(v6M implements a very restricted subset of Thumb2, but we
can cross that bridge when we get to it with appropriate
feature bits.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1507556919-24992-6-git-send-email-peter.maydell@linaro.org
Secure function return happens when a non-secure function has been
called using BLXNS and so has a particular magic LR value (either
0xfefffffe or 0xfeffffff). The function return via BX behaves
specially when the new PC value is this magic value, in the same
way that exception returns are handled.
Adjust our BX excret guards so that they recognize the function
return magic number as well, and perform the function-return
unstacking in do_v7m_exception_exit().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1507556919-24992-5-git-send-email-peter.maydell@linaro.org
Implement the BLXNS instruction, which allows secure code to
call non-secure code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1507556919-24992-4-git-send-email-peter.maydell@linaro.org
Implement the SG instruction, which we emulate 'by hand' in the
exception handling code path.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1507556919-24992-3-git-send-email-peter.maydell@linaro.org
Add the M profile secure MMU index values to the switch in
get_a32_user_mem_index() so that LDRT/STRT work correctly
rather than asserting at translate time.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1507556919-24992-2-git-send-email-peter.maydell@linaro.org
It is unlikely that we will ever want to call this helper passing
an argument other than the current PC. So just remove the argument,
and use the pc we already get from cpu_get_tb_cpu_state.
This change paves the way to having a common "tb_lookup" function.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
It looks like there was a transcription error when writing this code
initially. The code previously only decoded src or dst of rax. This
resolves
https://bugs.launchpad.net/qemu/+bug/1719984.
Signed-off-by: Todd Eisenberger <teisenbe@google.com>
Message-Id: <CAP26EVRNVb=Mq=O3s51w7fDhGVmf-e3XFFA73MRzc5b4qKBA4g@mail.gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
For the SG instruction and secure function return we are going
to want to do memory accesses using the MMU index of the CPU
in secure state, even though the CPU is currently in non-secure
state. Write arm_v7m_mmu_idx_for_secstate() to do this job,
and use it in cpu_mmu_index().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-17-git-send-email-peter.maydell@linaro.org
In cpu_mmu_index() we try to do this:
if (env->v7m.secure) {
mmu_idx += ARMMMUIdx_MSUser;
}
but it will give the wrong answer, because ARMMMUIdx_MSUser
includes the 0x40 ARM_MMU_IDX_M field, and so does the
mmu_idx we're adding to, and we'll end up with 0x8n rather
than 0x4n. This error is then nullified by the call to
arm_to_core_mmu_idx() which masks out the high part, but
we're about to factor out the code that calculates the
ARMMMUIdx values so it can be used without passing it through
arm_to_core_mmu_idx(), so fix this bug first.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-16-git-send-email-peter.maydell@linaro.org
Implement the security attribute lookups for memory accesses
in the get_phys_addr() functions, causing these to generate
various kinds of SecureFault for bad accesses.
The major subtlety in this code relates to handling of the
case when the security attributes the SAU assigns to the
address don't match the current security state of the CPU.
In the ARM ARM pseudocode for validating instruction
accesses, the security attributes of the address determine
whether the Secure or NonSecure MPU state is used. At face
value, handling this would require us to encode the relevant
bits of state into mmu_idx for both S and NS at once, which
would result in our needing 16 mmu indexes. Fortunately we
don't actually need to do this because a mismatch between
address attributes and CPU state means either:
* some kind of fault (usually a SecureFault, but in theory
perhaps a UserFault for unaligned access to Device memory)
* execution of the SG instruction in NS state from a
Secure & NonSecure code region
The purpose of SG is simply to flip the CPU into Secure
state, so we can handle it by emulating execution of that
instruction directly in arm_v7m_cpu_do_interrupt(), which
means we can treat all the mismatch cases as "throw an
exception" and we don't need to encode the state of the
other MPU bank into our mmu_idx values.
This commit doesn't include the actual emulation of SG;
it also doesn't include implementation of the IDAU, which
is a per-board way to specify hard-coded memory attributes
for addresses, which override the CPU-internal SAU if they
specify a more secure setting than the SAU is programmed to.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-15-git-send-email-peter.maydell@linaro.org
Implement the register interface for the SAU: SAU_CTRL,
SAU_TYPE, SAU_RNR, SAU_RBAR and SAU_RLAR. None of the
actual behaviour is implemented here; registers just
read back as written.
When the CPU definition for Cortex-M33 is eventually
added, its initfn will set cpu->sau_sregion, in the same
way that we currently set cpu->pmsav7_dregion for the
M3 and M4.
Number of SAU regions is typically a configurable
CPU parameter, but this patch doesn't provide a
QEMU CPU property for it. We can easily add one when
we have a board that requires it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-14-git-send-email-peter.maydell@linaro.org
Add support for v8M and in particular the security extension
to the exception entry code. This requires changes to:
* calculation of the exception-return magic LR value
* push the callee-saves registers in certain cases
* clear registers when taking non-secure exceptions to avoid
leaking information from the interrupted secure code
* switch to the correct security state on entry
* use the vector table for the security state we're targeting
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-13-git-send-email-peter.maydell@linaro.org
For v8M, exceptions from Secure to Non-Secure state will save
callee-saved registers to the exception frame as well as the
caller-saved registers. Add support for unstacking these
registers in exception exit when necessary.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-12-git-send-email-peter.maydell@linaro.org
In v8M, more bits are defined in the exception-return magic
values; update the code that checks these so we accept
the v8M values when the CPU permits them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-11-git-send-email-peter.maydell@linaro.org
Add the new M profile Secure Fault Status Register
and Secure Fault Address Register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-10-git-send-email-peter.maydell@linaro.org
In the v8M architecture, return from an exception to a PC which
has bit 0 set is not UNPREDICTABLE; it is defined that bit 0
is discarded [R_HRJH]. Restrict our complaint about this to v7M.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-9-git-send-email-peter.maydell@linaro.org
Attempting to do an exception return with an exception frame that
is not 8-aligned is UNPREDICTABLE in v8M; warn about this.
(It is not UNPREDICTABLE in v7M, and our implementation can
handle the merely-4-aligned case fine, so we don't need to
do anything except warn.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-8-git-send-email-peter.maydell@linaro.org
ARM v8M specifies that the INVPC usage fault for mismatched
xPSR exception field and handler mode bit should be checked
before updating the PSR and SP, so that the fault is taken
with the existing stack frame rather than by pushing a new one.
Perform this check in the right place for v8M.
Since v7M specifies in its pseudocode that this usage fault
check should happen later, we have to retain the original
code for that check rather than being able to merge the two.
(The distinction is architecturally visible but only in
very obscure corner cases like attempting an invalid exception
return with an exception frame in read only memory.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-7-git-send-email-peter.maydell@linaro.org
On exception return for v8M, the SPSEL bit in the EXC_RETURN magic
value should be restored to the SPSEL bit in the CONTROL register
banked specified by the EXC_RETURN.ES bit.
Add write_v7m_control_spsel_for_secstate() which behaves like
write_v7m_control_spsel() but allows the caller to specify which
CONTROL bank to use, reimplement write_v7m_control_spsel() in
terms of it, and use it in exception return.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-6-git-send-email-peter.maydell@linaro.org
Now that we can handle the CONTROL.SPSEL bit not necessarily being
in sync with the current stack pointer, we can restore the correct
security state on exception return. This happens before we start
to read registers off the stack frame, but after we have taken
possible usage faults for bad exception return magic values and
updated CONTROL.SPSEL.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-5-git-send-email-peter.maydell@linaro.org
In the v7M architecture, there is an invariant that if the CPU is
in Handler mode then the CONTROL.SPSEL bit cannot be nonzero.
This in turn means that the current stack pointer is always
indicated by CONTROL.SPSEL, even though Handler mode always uses
the Main stack pointer.
In v8M, this invariant is removed, and CONTROL.SPSEL may now
be nonzero in Handler mode (though Handler mode still always
uses the Main stack pointer). In preparation for this change,
change how we handle this bit: rename switch_v7m_sp() to
the now more accurate write_v7m_control_spsel(), and make it
check both the handler mode state and the SPSEL bit.
Note that this implicitly changes the point at which we switch
active SP on exception exit from before we pop the exception
frame to after it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-4-git-send-email-peter.maydell@linaro.org
Currently our M profile exception return code switches to the
target stack pointer relatively early in the process, before
it tries to pop the exception frame off the stack. This is
awkward for v8M for two reasons:
* in v8M the process vs main stack pointer is not selected
purely by the value of CONTROL.SPSEL, so updating SPSEL
and relying on that to switch to the right stack pointer
won't work
* the stack we should be reading the stack frame from and
the stack we will eventually switch to might not be the
same if the guest is doing strange things
Change our exception return code to use a 'frame pointer'
to read the exception frame rather than assuming that we
can switch the live stack pointer this early.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-3-git-send-email-peter.maydell@linaro.org
This properly forwards SMC events to EL2 when PSCI is provided by QEMU
itself and, thus, ARM_FEATURE_EL3 is off.
Found and tested with the Jailhouse hypervisor. Solution based on
suggestions by Peter Maydell.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Message-id: 4f243068-aaea-776f-d18f-f9e05e7be9cd@siemens.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Just as for external interrupts and I/O interrupts, we need to
initialize mchk_index during cpu reset.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Provides an interface for getting and setting the guest's extended
TOD-Clock via a single ioctl to kvm. If the ioctl fails because it
is not support by kvm, then we fall back to the old style of
retrieving the clock via two ioctls.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
[split failure change from epoch index change]
Message-Id: <20171004105751.24655-2-borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
[some cosmetic fixes]
Using virtual memory access is wrong and will soon include low-address
protection checks, which is to be bypassed for STFL.
STFL is a privileged instruction and using LowCore requires
!CONFIG_USER_ONLY, so add the ifdef and move the declaration to the
right place.
This was originally part of a bigger STFL(E) refactoring.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170927170027.8539-4-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Will be handy in the future.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928134609.16985-6-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
core_id is not needed by linux-user, as the core_id a.k.a. CPU address
is only accessible from kernel space.
Therefore, drop next_core_id and make cpu_index get autoassigned again
for linux-user.
While at it, shield core_id and cpuid completely from linux-user. cpuid
can also only be queried from kernel space.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928134609.16985-5-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Not that it would matter in the near future, but it is actually 2048
bytes, therefore 16384 possible bits.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928134609.16985-4-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's move it into the machine, so we trigger the IRQ after setting
ms->possible_cpus (which SCLP uses to construct the list of
online CPUs).
This also fixes a problem reported by Thomas Huth, whereby qemu can be
crashed using the none machine
qemu-s390x-softmmu -M none -monitor stdio
-> device_add qemu-s390-cpu
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928134609.16985-3-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We don't wrap addresses in the mmu for the _real case, therefore the
behavior should be unchanged.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170926183318.12995-7-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Low address protection checks will be moved into the mmu later.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170926183318.12995-6-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
As we properly handle the return address now, we can drop
potential_page_fault().
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170926183318.12995-5-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Looks like, lurag was not loading 64bit but only 32bit.
As we properly handle the return address now, we can drop
potential_page_fault().
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170926183318.12995-4-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This makes it easy to access real addresses (prefix) and in addition
checks for valid memory addresses, which is missing when using e.g.
stl_phys().
We can later reuse it to implement low address protection checks (then
we might even decide to introduce yet another MMU for absolute
addresses, just for handling storage keys and low address protection).
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170926183318.12995-3-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
It should have been a >=, but let's directly perform a proper access
check to also be able to deal with hotplugged memory later.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170926183318.12995-2-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
env->psa is a 64bit value, while we copy 4 bytes into the save area,
resulting always in 0 getting stored.
Let's try to reduce such errors by using a proper structure. While at
it, use correct cpu->be conversion (and get_psw_mask()), as we will be
reusing this code for TCG soon.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170922140338.6068-1-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Define default CPU type in generic way in machine class_init
and let common machine code handle cpu_model parsing.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <1505998749-269631-1-git-send-email-imammedo@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The STFLE bits for the MSA (extension) facilities simply indicate that
the respective instructions can be executed. The QUERY subfunction can then
be used to identify which features exactly are available.
Availability of subfunctions can also vary on real hardware. For now, we
simply implement a CPU model without any available subfunctions except
QUERY (which is always around).
As all MSA functions behave quite similarly, we can use one translation
handler for now. Prepare the code for implementation of actual subfunctions.
At least MSA is helpful for now, as older Linux kernels require this
facility when compiled for a z9 model. Allow to enable the facilities
for the qemu cpu model.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170920153016.3858-4-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We want to use it in another file.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170920153016.3858-3-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Missing and is used inside Linux in the context of CPACF.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170920153016.3858-2-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Handle the translation from vga chars to curses chars in curses_update()
instead of console_write_ch(). Purge any curses support bits from
ui/console.h include file.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20170927103811.19249-1-kraxel@redhat.com
-----BEGIN PGP SIGNATURE-----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=/+LV
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgilbert/tags/pull-migration-20170927a' into staging
Migration pull 2017-09-27
# gpg: Signature made Wed 27 Sep 2017 14:56:23 BST
# gpg: using RSA key 0x0516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* remotes/dgilbert/tags/pull-migration-20170927a:
migration: Route more error paths
migration: Route errors up through vmstate_save
migration: wire vmstate_save_state errors up to vmstate_subsection_save
migration: Check field save returns
migration: check pre_save return in vmstate_save_state
migration: pre_save return int
migration: disable auto-converge during bulk block migration
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Contains
* a number of Mac machine type fixes
* a number of embedded machine type fixes (preliminary to adding the
Sam460ex board)
* a important fix for handling of migration with KVM PR
* assorted other minor fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=NL90
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.11-20170927' into staging
ppc patch queue 2017-09-27
Contains
* a number of Mac machine type fixes
* a number of embedded machine type fixes (preliminary to adding the
Sam460ex board)
* a important fix for handling of migration with KVM PR
* assorted other minor fixes and cleanups
# gpg: Signature made Wed 27 Sep 2017 08:40:48 BST
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.11-20170927: (26 commits)
macio: use object link between MACIO_IDE and MAC_DBDMA object
macio: pass channel into MACIOIDEState via qdev property
mac_dbdma: remove DBDMA_init() function
mac_dbdma: QOMify
mac_dbdma: remove unused IO fields from DBDMAState
spapr: fix the value of SDR1 in kvmppc_put_books_sregs()
ppc/pnv: check for OPAL firmware file presence
ppc: remove all unused CPU definitions
ppc: remove unused CPU definitions
spapr_pci: make index property mandatory
macio: convert pmac_ide_ops from old_mmio
ppc/pnv: Improve macro parenthesization
spapr: introduce helpers to migrate HPT chunks and the end marker
ppc/kvm: generalize the use of kvmppc_get_htab_fd()
ppc/kvm: change kvmppc_get_htab_fd() to return -errno on error
ppc: Fix OpenPIC model
ppc/ide/macio: Add missing registers
ppc/mac: More rework of the DBDMA emulation
ppc/mac: Advertise a high clock frequency for NewWorld Macs
ppc: QOMify g3beige machine
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Modify the pre_save method on VMStateDescription to return an int
rather than void so that it potentially can fail.
Changed zillions of devices to make them return 0; the only
case I've made it return non-0 is hw/intc/s390_flic_kvm.c that already
had an error_report/return case.
Note: If you add an error exit in your pre_save you must emit
an error_report to say why.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170925112917.21340-2-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We disabled ais for 2.10, so let's also remove it from the z14
default model.
Fixes: 3f2d07b3b0 ("s390x/ais: for 2.10 stable: disable ais facility")
CC: qemu-stable@nongnu.org
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20170927072030.35737-2-borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
When running with KVM PR, if a new HPT is allocated we need to inform
KVM about the HPT address and size. This is currently done by hacking
the value of SDR1 and pushing it to KVM in several places.
Also, migration breaks the guest since it is very unlikely the HPT has
the same address in source and destination, but we push the incoming
value of SDR1 to KVM anyway.
This patch introduces a new virtual hypervisor hook so that the spapr
code can provide the correct value of SDR1 to be pushed to KVM each
time kvmppc_put_books_sregs() is called.
It allows to get rid of all the hacking in the spapr/kvmppc code and
it fixes migration of nested KVM PR.
Suggested-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Remove *all* unused CPU definitions as indicated by compile-time
`#if 0` constructs.
Signed-off-by: John Snow <jsnow@redhat.com>
[dwg: Removed some additional now-useless comments]
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Following commit aef77960, remove now-unused definitions from
cpu-models.h.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The use of KVM_PPC_GET_HTAB_FD is open-coded in kvmppc_read_hptes()
and kvmppc_write_hpte().
This patch modifies kvmppc_get_htab_fd() so that it can be used
everywhere we need to access the in-kernel htab:
- add an index argument
=> only kvmppc_read_hptes() passes an actual index, all other users
pass 0
- add an errp argument to propagate error messages to the caller.
=> spapr migration code prints the error
=> hpte helpers pass &error_abort to keep the current behavior
of hw_error()
While here, this also fixes a bug in kvmppc_write_hpte() so that it
opens the htab fd for writing instead of reading as it currently does.
This never broke anything because we currently never call this code,
as explained in the changelog of commit c138593380:
"This support updating htab managed by the hypervisor. Currently
we don't have any user for this feature. This actually bring the
store_hpte interface in-line with the load_hpte one. We may want
to use this when we want to emulate henter hcall in qemu for HV
kvm."
The above is still true today.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When kvmppc_get_htab_fd() fails, its return value is propagated up to
qemu_savevm_state_iterate() or to qemu_savevm_state_complete_precopy().
All savevm handlers expect to receive a negative errno on error.
Let's patch kvmppc_get_htab_fd() accordingly.
While here, let's change htab_load() in the spapr code to also
propagate the error, since it doesn't make sense to abort() if
we couldn't get the htab fd from KVM.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Despite its name it is a 440 core CPU
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
