The ptev variable in ppc6xx_tlb_pte_check() is used only once and just
obfuscates an otherwise clear value. Get rid of it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The ptem variable in ppc6xx_tlb_pte_check() is used only once,
simplify by removing it as the value is already clear itself without
adding a local name for it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The mmask local variable is a less descriptive local name for a
constant. Drop it and use the constant directly in the two places it
is needed.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reorganise ppc_hash32_pp_prot() swapping the if legs so it does not
test for negative first and clean up to make it shorter. Also rename
it to ppc_hash32_prot().
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Updated many VSX instructions to use tcg_gen_qemu_ld/st_i128, instead of using
tcg_gen_qemu_ld/st_i64 consecutively.
Introduced functions {get,set}_vsr_full to facilitate the above & for future use.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Updated instructions {l, st}vx to use tcg_gen_qemu_ld/st_i128,
instead of using 64 bits loads/stores in succession.
Introduced functions {get, set}_avr_full in vmx-impl.c.inc to
facilitate the above, and potential future usage.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Those functions are used to ld/st data to and from Altivec registers,
in 64 bits chunks, and are only used in vmx-impl.c.inc file,
hence the clean-up movement.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Moving the following instructions to decodetree specification:
xvcmp{eq, gt, ge, ne}{s, d}p : XX3-form
The changes were verified by validating that the tcg-ops generated for those
instructions remain the same which were captured using the '-d in_asm,op' flag.
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Moving the following instructions to decodetree specification:
lxv{b16, d2, h8, w4, ds, ws}x : X-form
stxv{b16, d2, h8, w4}x : X-form
The changes were verified by validating that the tcg-ops generated for those
instructions remain the same, which were captured using the '-d in_asm,op' flag.
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Moving the following instructions to decodetree specification :
{l, st}xvl(l) : X-form
The changes were verified by validating that the tcg-ops generated by those
instructions remain the same, which were captured using the '-d in_asm,op' flag.
Also added a new function do_ea_calc_ra to calculate the effective address :
EA <- (RA == 0) ? 0 : GPR[RA], which is now used by the above-said insns,
and shall be used later by (p){lx, stx}vp insns.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
[np: Fix 32-bit build]
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Moving the following instructions to decodetree specification :
lxs{d, iwa, ibz, ihz, iwz, sp}x : X-form
stxs{d, ib, ih, iw, sp}x : X-form
The changes were verified by validating that the tcg-ops generated by those
instructions remain the same, which were captured using the '-d in_asm,op' flag.
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Moving the following instructions to decodetree specification :
xxl{and, andc, or, orc, nor, xor, nand, eqv} : XX3-form
The changes were verified by validating that the tcg ops generated by those
instructions remain the same, which were captured with the '-d in_asm,op' flag.
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Moving the following instructions to decodetree specification:
x{s, v}{add, sub, mul, div}{s, d}p : XX3-form
xs{max, min}dp, xv{max, min}{s, d}p : XX3-form
The changes were verfied by validating that the tcg ops generated by those
instructions remain the same, which were captured with the '-d in_asm,op' flag.
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Moving PPC2_ISA300 flag check out of do_helper_XX3 method in vmx-impl.c.inc
so that the helper can be used with other instructions as well.
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
No need for a full comparison; xor produces non-zero bits for QC just fine.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Chinmay Rath <rath.chinmay@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Moving the following instructions to decodetree specification :
v{add,sub}{u,s}{b,h,w}s : VX-form
The changes were verified by validating that the tcg ops generated by those
instructions remain the same, which were captured with the '-d in_asm,op' flag.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Additional END state 'info pic' information as added. The 'ignore',
'crowd' and 'precluded escalation control' bits of an Event Notification
Descriptor are all used when delivering an interrupt targeting a VP-group
or crowd.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Kowal <kowal@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
In XIVE Gen 2 there were some minor changes to the TIMA header that were
updated when printed.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Kowal <kowal@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Moving xive2_nvp_pic_print_info() to align with the other "pic_print_info"
functions.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Kowal <kowal@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Fail VST entry address computation if firmware doesn't define a descriptor
for one of the Virtualization Structure Tables (VST), there's no point in
trying to compute the address of its entry. Abort the operation and log
an error.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Kowal <kowal@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Set Translation Table for the NVC port space is missing. The xive model
doesn't take into account the remapping of IO operations via the Set
Translation Table but firmware is allowed to define it for the Notify
Virtual Crowd (NVC), like it's already done for the other VST tables.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Kowal <kowal@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Enable NVG and NVC VST tables for index compression which indicates the number
of bits the address is shifted to the right for the table accesses.
The compression values are defined as:
0000 - No compression
0001 - 1 bit shift
0010 - 2 bit shift
....
1000 - 8 bit shift
1001-1111 - No compression
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Kowal <kowal@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Both the virtualization layer (VC) and presentation layer (PC) need to
be configured to access the VSTs. Since the information is redundant,
the xive model combines both into one set of tables and only the
definitions going through the VC are kept. The definitions through the
PC are ignored. That works well as long as firmware calls the VC for
all the tables.
For the NVG and NVC tables, it can make sense to only configure them
with the PC, since they are only used by the presenter. So this patch
allows firmware to configure the VST tables through the PC as well.
The definitions are still shared, since the VST tables can be set
through both the VC and/or PC, they are dynamically re-mapped in
memory by first deleting the memory subregion.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Kowal <kowal@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The cache watch facility uses the same register interface to handle
entries in the NVP, NVG and NVC tables. A bit-field in the 'watchX
specification' register tells the table type. So far, that bit-field
was not read and the code assumed a read/write to the NVP table.
This patch allows to read/write entries in the NVG and NVC table as
well.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Kowal <kowal@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Adds support for writing a completion notification byte in memory
whenever a cache flush or queue sync inject operation is requested by
software. QEMU does not cache any of the XIVE data that is in memory and
therefore it simply writes the completion notification byte at the time
that the operation is requested.
Co-authored-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Michael Kowal <kowal@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Made changes to some structure and define elements to ease review in
next patchset.
Signed-off-by: Michael Kowal <kowal@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
XIVE offers a 'cache watch facility', which allows software to read/update
a potentially cached table entry with no software lock. There's one such
facility in the Virtualization Controller (VC) to update the ESB and END
entries and one in the Presentation Controller (PC) to update the
NVP/NVG/NVC entries.
Each facility has 4 cache watch engines to control the updates and
firmware can request an available engine by querying the hardware
'watch_assign' register of the VC or PC. The engine is then reserved and
is released after the data is updated by reading the 'watch_spec' register
(which also allows to check for a conflict during the update).
If no engine is available, the special value 0xFF is returned and
firmware is expected to repeat the request until an engine becomes
available.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Kowal <kowal@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
In this commit Write a qtest pnv-spi-seeprom-test to check the
SPI transactions between spi controller and seeprom device.
Signed-off-by: Chalapathi V <chalapathi.v@linux.ibm.com>
Acked-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Caleb Schlossin <calebs@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Add Microchip's 25CSM04 Serial EEPROM to m25p80. 25CSM04 provides 4 Mbits
of Serial EEPROM utilizing the Serial Peripheral Interface (SPI) compatible
bus. The device is organized as 524288 bytes of 8 bits each (512Kbyte) and
is optimized for use in consumer and industrial applications where reliable
and dependable nonvolatile memory storage is essential.
Signed-off-by: Chalapathi V <chalapathi.v@linux.ibm.com>
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
In this commit SPI shift engine and sequencer logic is implemented.
Shift engine performs serialization and de-serialization according to the
control by the sequencer and according to the setup defined in the
configuration registers. Sequencer implements the main control logic and
FSM to handle data transmit and data receive control of the shift engine.
Signed-off-by: Chalapathi V <chalapathi.v@linux.ibm.com>
Reviewed-by: Caleb Schlossin <calebs@linux.vnet.ibm.com>
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
SPI controller device model supports a connection to a single SPI responder.
This provide access to SPI seeproms, TPM, flash device and an ADC controller.
All SPI function control is mapped into the SPI register space to enable full
control by firmware. In this commit SPI configuration component is modelled
which contains all SPI configuration and status registers as well as the hold
registers for data to be sent or having been received.
An existing QEMU SSI framework is used and SSI_BUS is created.
Signed-off-by: Chalapathi V <chalapathi.v@linux.ibm.com>
Reviewed-by: Caleb Schlossin <calebs@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
[np: Fix FDT macro compile for qtest]
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
In this commit target specific dependency from include/hw/ppc/pnv_xscom.h
has been removed so that pnv_xscom.h can be included outside hw/ppc.
Signed-off-by: Chalapathi V <chalapathi.v@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Caleb Schlossin <calebs@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Recent POWER CPUs can operate in "LPAR per core" or "LPAR per thread"
modes. In per-core mode, some SPRs and IPI doorbells are shared between
threads in a core. In per-thread mode, supervisor and user state is
not shared between threads.
OpenPOWER systems after POWER8 use LPAR per thread mode, and it is
required for KVM. Enterprise systems use LPAR per core mode, as they
partition the machine by core.
Implement a lpar-per-core machine option for powernv machines. This
is fixed true for POWER8 machines, and defaults off for P9 and P10.
With this change, powernv8 SMT now works sufficiently to run Linux,
with a single socket. Multi-threaded KVM guests still have problems,
as does multi-socket Linux boot.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The PC unit in the processor core contains xscom registers that provide
low level status and control of the CPU.
This implements "direct controls", sufficient for skiboot firmware,
which uses it to send NMI IPIs between CPUs.
POWER10 is sufficiently different from POWER9 (particularly with respect
to QME and special wakeup) that it is not trivial to implement POWER9
support by reusing the code.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Power CPUs have an execution control facility that can pause, resume,
and cause NMIs, among other things. Add a function that will nmi a CPU
and resume it if it was paused, in preparation for implementing the
control facility.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Big-core implementation is complete, so expose it as a machine
property that may be set with big-core=on option on powernv9 and
powernv10 machines.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
POWER10 has a quirk in its ChipTOD addressing that requires the even
small-core to be selected even when programming the odd small-core.
This allows skiboot chiptod init to run in big-core mode.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Power9 CPUs have a core thread state register accessible via SPRC/SPRD
indirect registers. This register includes a bit for big-core mode,
which skiboot requires.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Power9/10 CPUs have PVR[51] set in small-core mode and clear in big-core
mode. This is used by skiboot firmware.
PVR is not hypervisor-privileged but it is not so important that spapr
to implement this because it's generally masked out of PVR matching code
in kernels, and only used by firmware.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
device-tree building needs to account for big-core mode, because it is
driven by qemu cores (small cores). Every second core should be skipped,
and every core should describe threads for both small-cores that make
up the big core.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
POWER9 and POWER10 machines come in two variants, big-core and
small-core. Big-core machines are SMT8 from software's point of view,
but the low level platform topology ("xscom registers and pervasive
addressing"), these look more like a pair of small cores ganged
together.
Presently the way this is modelled is to create one SMT8 PnvCore and add
special cases to xscom and pervasive for big-core mode that tries to
split this into two small cores, but this is becoming too complicated to
manage.
A better approach is to create 2 core structures and ganging them
together to look like an SMT8 core in TCG. Then the xscom and pervasive
models mostly do not need to differentiate big and small core modes.
This change adds initial mode bits and QEMU topology handling to
split SMT8 cores into 2xSMT4 cores.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The decision to branch out to a slower SMT path in instruction
emulation will become a bit more complicated with the way that
"big-core" topology that will be implemented in subsequent changes.
Hide these details from the wider CPU emulation code with a bool
has_smt_siblings flag that can be set by machine initialisation.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Add helpers for TCG code to determine if there are SMT siblings
sharing per-core and per-lpar registers. This simplifies the
callers and makes SMT register topology simpler to modify with
later changes.
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The way SMT thread siblings are matched is clunky, using hard-coded
logic that checks the PIR SPR.
Change that to use a new core_index variable in the CPUPPCState,
where all siblings have the same core_index. CPU realize routines have
flexibility in setting core/sibling topology.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The chip_pir chip class method allows the platform to set the PIR
processor identification register. Extend this to a more general
ID function which also allows the TIR to be set. This is in
preparation for "big core", which is a more complicated topology
of cores and threads.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Use a class attribute to specify the number of SMT threads per core
permitted for different machines, 8 for powernv8 and 4 for powernv9/10.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
SPRC/SPRD were recently added to all BookS CPUs supported, but
they are only tested on POWER9 and POWER10, so restrict them to
those CPUs.
SPR indirect scratch registers presently replicated per-CPU like
SMT SPRs, but the PnvCore is a better place for them since they
are restricted to P9/P10.
Also add SPR indirect read access to core thread state for POWER9
since skiboot accesses that when booting to check for big-core
mode.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The timebase state machine is per per-core state and can be driven
by any thread in the core. It is currently implemented as a hack
where the state is in a CPU structure and only thread 0's state is
accessed by the chiptod, which limits programming the timebase
side of the state machine to thread 0 of a core.
Move the state out into PnvCore and share it among all threads.
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
This helps move core state from CPU to core structures.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
