We need to make sure the link is masked properly along the
use_nullify_skip path. The other three settings of a link
register already use this.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This will be how we ensure that the IAOQ is always
valid per PSW.W, therefore all stores to these two
variables must be done with this function.
Use third argument -1 if the destination is always dynamic,
and fourth argument NULL if the destination is always static.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In form_gva and cpu_get_tb_cpu_state, we must truncate when PSW_W == 0.
In space_select, the bits that choose the space depend on PSW_W.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Dump all 64 bits for pa2.0 and low 32 bits for pa1.x.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
With pa2.0, absolute addresses are not the same as physical addresses,
and undergo a transformation based on PSW_W.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
With 64-bit registers, there are 16 carry bits in the PSW.
Clear reserved bits based on cpu revision.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Prepare for the qemu binary supporting both pa10 and pa20
at the same time.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Select the proper carry bit for input to the arithmetic
and for output for the condition.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This instruction always uses the input carry from bit 32,
but produces all 16 output carry bits.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The destination is TCGv_i32, so use tcg_gen_qemu_ld_i32
not tcg_gen_qemu_ld_reg.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Replace with tcg_temp_new_tl without recording into ctx.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Replace with tcg_temp_new without recording into ctx.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Complete the data structure conversion started earlier. This reduces
the perf overhead of hppa_get_physical_address from ~5% to ~0.25%.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
No need to trigger the large_page_mask code unnecessarily.
Drop the now unused HPPATLBEntry.page_size field.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Replace the va_b and va_b fields with the interval tree node.
The actual interval tree is not yet used.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Use a separate mmu index for PSW_P enabled vs disabled.
This means we can elide the tlb flush in cpu_hppa_put_psw
when PSW_P changes. This turns out to be the majority
of all tlb flushes.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Finish the convertion started with commit de6cd7599b
("meson: Replace softmmu_ss -> system_ss"). If the
$target_type is 'system', then use the target_system_arch[]
source set :)
Mechanical change doing:
$ sed -i -e s/target_softmmu_arch/target_system_arch/g \
$(git grep -l target_softmmu_arch)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20231004090629.37473-13-philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This function is now empty, so remove it. In the case of
m68k and tricore, this empties the class instance initfn,
so remove those as well.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Allow the name 'cpu_env' to be used for something else.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Retain the separate structure to emphasize its importance.
Enforce CPUArchState always follows CPUState without padding.
Reviewed-by: Anton Johansson <anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The omission of alignment has technically been wrong since
269bd5d8f6, where QEMU_ALIGNED was added to CPUTLBDescFast.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Wire up the hppa diag instruction to support Block-TLBs
when called with the 0x100 value.
The diag_btlb() helper function does all necessary steps
to emulate the PDC BTLB firmware function, which includes
providing BTLB info, adding a new BTLB, deleting a BTLB
and removing all BTLBs.
Signed-off-by: Helge Deller <deller@gmx.de>
Extract the immediate value given by the diagnose CPU instruction.
This is needed to distinguish the various diagnose calls.
Signed-off-by: Helge Deller <deller@gmx.de>
Change the TLB code to store the Block-TLBs at the beginning
of the TLB table. New 4k TLB entries which are added later
shall not overwrite any of the BTLB entries.
Make sure that when the TLB is cleared by the OS via the ptlbe
instruction, the Block-TLBs will not be dropped.
Signed-off-by: Helge Deller <deller@gmx.de>
All these files only access the translator_ld/st API declared
in "exec/translator.h". The CPU ld/st API from declared in
"exec/cpu_ldst.h" is not used, remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230828221314.18435-5-philmd@linaro.org>
The MMU indices 9-15 will use shorter assembler instructions
when run on a x86-64 host. So, switch over to those to get
smaller code and maybe minimally faster emulation.
Signed-off-by: Helge Deller <deller@gmx.de>
Convert hppa_get_physical_address() to use the privilege helper macro.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Avoid using hardcoded values when calling the tlb_flush*() functions.
Instead, define and use HPPA_MMU_FLUSH_MASK (keeping the current
behavior, which doesn't flush the physical address MMU).
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Add two macros which convert privilege level to/from MMU index:
- PRIV_TO_MMU_IDX(priv)
returns the MMU index for the given privilege level
- MMU_IDX_TO_PRIV(mmu_idx)
returns the corresponding privilege level for this MMU index
The introduction of those macros make the code easier to read and
will help to improve performance in follow-up patch.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The hppa CPU has 4 privilege levels (0-3).
Mention the missing PL1 and PL2 levels, although the Linux kernel
uses only 0 (KERNEL) and 3 (USER). Not sure about HP-UX.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
On hppa the Instruction Address Offset Queue (IAOQ) registers specifies
the next to-be-executed instructions addresses. Each generated TB writes those
registers at least once, so those registers are used heavily in generated
code.
Looking at the generated assembly, for a x86-64 host this code
to write the address $0x7ffe826f into iaoq_f is generated:
0x7f73e8000184: c7 85 d4 01 00 00 6f 82 movl $0x7ffe826f, 0x1d4(%rbp)
0x7f73e800018c: fe 7f
0x7f73e800018e: c7 85 d8 01 00 00 73 82 movl $0x7ffe8273, 0x1d8(%rbp)
0x7f73e8000196: fe 7f
With the trivial change, by moving the variables iaoq_f and iaoq_b to
the top of struct CPUArchState, the offset to %rbp is reduced (from
0x1d4 to 0), which allows the x86-64 tcg to generate 3 bytes less of
generated code per move instruction:
0x7fc1e800018c: c7 45 00 6f 82 fe 7f movl $0x7ffe826f, (%rbp)
0x7fc1e8000193: c7 45 04 73 82 fe 7f movl $0x7ffe8273, 4(%rbp)
Overall this is a reduction of generated code (not a reduction of
number of instructions).
A test run with checks the generated code size by running "/bin/ls"
with qemu-user shows that the code size shrinks from 1616767 to 1569273
bytes, which is ~97% of the former size.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: qemu-stable@nongnu.org
Replace the 0/-1 result with true/false.
Invert the sense of the test of all callers.
Document the function.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230707204054.8792-25-richard.henderson@linaro.org>
Signed-off-by: Anton Johansson <anjo@rev.ng>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230621135633.1649-4-anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We use the user_ss[] array to hold the user emulation sources,
and the softmmu_ss[] array to hold the system emulation ones.
Hold the latter in the 'system_ss[]' array for parity with user
emulation.
Mechanical change doing:
$ sed -i -e s/softmmu_ss/system_ss/g $(git grep -l softmmu_ss)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230613133347.82210-10-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
int_helper.c only contains system emulation code:
remove the #ifdef'ry and move the file to the meson
softmmu source set.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230602223016.58647-1-philmd@linaro.org>
