Armv8.1+ cpus have Virtual Host Extension (VHE) which added non-secure
EL2 virtual timer.
This change adds it to fullfil Arm BSA (Base System Architecture)
requirements.
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Message-id: 20230913140610.214893-2-marcin.juszkiewicz@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Just like d7ef5e16a1 sets SCR_EL3.HXEn for FEAT_HCX, this commit
handles SCR_EL3.FGTEn for FEAT_FGT:
When we direct boot a kernel on a CPU which emulates EL3, we need to
set up the EL3 system registers as the Linux kernel documentation
specifies:
https://www.kernel.org/doc/Documentation/arm64/booting.rst
> For CPUs with the Fine Grained Traps (FEAT_FGT) extension present:
> - If EL3 is present and the kernel is entered at EL2:
> - SCR_EL3.FGTEn (bit 27) must be initialised to 0b1.
Cc: qemu-stable@nongnu.org
Signed-off-by: Fabian Vogt <fvogt@suse.de>
Message-id: 4831384.GXAFRqVoOG@linux-e202.suse.de
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The cortex-a710 is a first generation ARMv9.0-A processor.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230831232441.66020-3-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the Configuration Frame controller (CFRAME_REG) and the
Configuration Frame broadcast controller (CFRAME_BCAST_REG) to the
Versal machine.
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230831165701.2016397-9-francisco.iglesias@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the Configuration Frame Unit (CFU_APB, CFU_FDRO and CFU_SFR) to
the Versal machine.
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Acked-by: Edgar E. Iglesias <edgar@zeroasic.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230831165701.2016397-8-francisco.iglesias@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
and replace the SDState::spi attribute with a test checking the
SDProto array of commands.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
and get rid of an unnecessary drive_get(IF_MTD) call.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When the -nodefaults option is set, flash devices should be created
with :
-blockdev node-name=fmc0,driver=file,filename=./flash.img \
-device mx66u51235f,cs=0x0,bus=ssi.0,drive=fmc0 \
To be noted that in this case, the ROM will not be installed and the
initial boot sequence (U-Boot loading) will fetch instructions using
SPI transactions which is significantly slower. That's exactly how HW
operates though.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This to avoid indexes conflicts on the same SSI bus. Adapt machines
using multiple devices on the same bus to avoid breakage.
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Currently, a set of default flash devices is created at machine init
and drives defined on the QEMU command line are associated to the FMC
and SPI controllers in sequence :
-drive file<file>,format=raw,if=mtd
-drive file<file1>,format=raw,if=mtd
The CS lines are wired in the same creation loop. This makes a strong
assumption on the ordering and is not very flexible since only a
limited set of flash devices can be defined : 1 FMC + 1 or 2 SPI,
which is less than what the SoC really supports.
A better alternative would be to define the flash devices on the
command line using a blockdev attached to a CS line of a SSI bus :
-blockdev node-name=fmc0,driver=file,filename=./flash.img
-device mx66u51235f,cs=0x0,bus=ssi.0,drive=fmc0
However, user created flash devices are not correctly wired to their
SPI controller and consequently can not be used by the machine. Fix
that and wire the CS lines of all available devices when the SSI bus
is reset.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
On 32-bit hosts, RAM has a 2047 MB limit. Use a macro to define the
default ram size of machines (AST2600 SoC) that can have 2 GB.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
* Some of the preliminary patches for Cortex-A710 support
* i.MX7 and i.MX6UL refactoring
* Implement SRC device for i.MX7
* Catch illegal-exception-return from EL3 with bad NSE/NS
* Use 64-bit offsets for holding time_t differences in RTC devices
* Model correct number of MPU regions for an505, an521, an524 boards
-----BEGIN PGP SIGNATURE-----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=MFh3
-----END PGP SIGNATURE-----
Merge tag 'pull-target-arm-20230831' of https://git.linaro.org/people/pmaydell/qemu-arm into staging
target-arm queue:
* Some of the preliminary patches for Cortex-A710 support
* i.MX7 and i.MX6UL refactoring
* Implement SRC device for i.MX7
* Catch illegal-exception-return from EL3 with bad NSE/NS
* Use 64-bit offsets for holding time_t differences in RTC devices
* Model correct number of MPU regions for an505, an521, an524 boards
# -----BEGIN PGP SIGNATURE-----
#
# iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmTwbukZHHBldGVyLm1h
# eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3ihBD/wK8Iz0KpTAwZBDAodnSZrh
# tQnJAvYFp8CxA4O8sZ9IeWsZh90gzsTCZi0NqUTTzvWCJfxkB7qTPdlJT5IzVxou
# oEUk2aogSJhRA3XRJzqArXsPlnZGSYDbtwKx4VtfCvOCCH08Y7nhnFaRj1oFnR4Q
# 0PE/8YtGXTBxLHrO8U3tomg7zElzOUP8ZVZtb30BOyw1jtfSD03IZR8dzpA43u1E
# Hh418WvVekmwFoFNh8yUeHzbyXMZufzvbJPuDGJ8pPWwIpvSG6chOnKF8jZll+Ur
# DqOsDkGlQgcBR2QwYfSPClrEkX8yahJ95PBfM6giG+DQC7OiElqXqTiUGZcpgUVo
# uSUbzS4YPsxCnyVV6SBXV+f/8hdXBxOSHTgl7OAFa8X9OwWwspxHJ/v2o/2ibnUT
# hTTkFp/w1nQwVEN8xf1DOUpm/J2Wr8UeH4f776daSrfKAol2BKbHb8dOgGLQCwqb
# G+iDcE4bkzRqly6f+uVk8xSEZDd9P1NYoxKV+gNlV1dTspdHVpTC+rXMa8dRw5hI
# 4KgaAslj++Xa229xkjORXCJ1cICRIebYg7+SjvTtGBYsFV7plsCcYb/R9yLmhVCf
# fKHKKaYe9sQJ82apOIkTc+nnW8BQQx6XUmU/A//iZ8JGLk6DpJcZ8f1m/2rVZTsl
# 9+lsmpBf4w+uR4o+Womhfw==
# =MFh3
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 31 Aug 2023 06:43:53 EDT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [full]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [full]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [full]
# gpg: aka "Peter Maydell <peter@archaic.org.uk>" [unknown]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* tag 'pull-target-arm-20230831' of https://git.linaro.org/people/pmaydell/qemu-arm: (24 commits)
hw/arm: Set number of MPU regions correctly for an505, an521, an524
hw/arm/armv7m: Add mpu-ns-regions and mpu-s-regions properties
target/arm: Do all "ARM_FEATURE_X implies Y" checks in post_init
rtc: Use time_t for passing and returning time offsets
hw/rtc/aspeed_rtc: Use 64-bit offset for holding time_t difference
hw/rtc/twl92230: Use int64_t for sec_offset and alm_sec
hw/rtc/m48t59: Use 64-bit arithmetic in set_alarm()
target/arm: Catch illegal-exception-return from EL3 with bad NSE/NS
Add i.MX7 SRC device implementation
Add i.MX7 missing TZ devices and memory regions
Refactor i.MX7 processor code
Add i.MX6UL missing devices.
Refactor i.MX6UL processor code
Remove i.MX7 IOMUX GPR device from i.MX6UL
target/arm: properly document FEAT_CRC32
target/arm: Implement FEAT_HPDS2 as a no-op
target/arm: Suppress FEAT_TRBE (Trace Buffer Extension)
target/arm: Apply access checks to neoverse-v1 special registers
target/arm: Apply access checks to neoverse-n1 special registers
target/arm: Introduce make_ccsidr64
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The IoTKit, SSE200 and SSE300 all default to 8 MPU regions. The
MPS2/MPS3 FPGA images don't override these except in the case of
AN547, which uses 16 MPU regions.
Define properties on the ARMSSE object for the MPU regions (using the
same names as the documented RTL configuration settings, and
following the pattern we already have for this device of using
all-caps names as the RTL does), and set them in the board code.
We don't actually need to override the default except on AN547,
but it's simpler code to have the board code set them always
rather than tracking which board subtypes want to set them to
a non-default value separately from what that value is.
Tho overall effect is that for mps2-an505, mps2-an521 and mps3-an524
we now correctly use 8 MPU regions, while mps3-an547 stays at its
current 16 regions.
It's possible some guest code wrongly depended on the previous
incorrectly modeled number of memory regions. (Such guest code
should ideally check the number of regions via the MPU_TYPE
register.) The old behaviour can be obtained with additional
-global arguments to QEMU:
For mps2-an521 and mps2-an524:
-global sse-200.CPU0_MPU_NS=16 -global sse-200.CPU0_MPU_S=16 -global sse-200.CPU1_MPU_NS=16 -global sse-200.CPU1_MPU_S=16
For mps2-an505:
-global sse-200.CPU0_MPU_NS=16 -global sse-200.CPU0_MPU_S=16
NB that the way the implementation allows this use of -global
is slightly fragile: if the board code explicitly sets the
properties on the sse-200 object, this overrides the -global
command line option. So we rely on:
- the boards that need fixing all happen to use the SSE defaults
- we can write the board code to only set the property if it
is different from the default, rather than having all boards
explicitly set the property
- the board that does need to use a non-default value happens
to need to set it to the same value (16) we previously used
This works, but there are some kinds of refactoring of the
mps2-tz.c code that would break the support for -global here.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1772
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230724174335.2150499-4-peter.maydell@linaro.org
M-profile CPUs generally allow configuration of the number of MPU
regions that they have. We don't currently model this, so our
implementations of some of the board models provide CPUs with the
wrong number of regions. RTOSes like Zephyr that hardcode the
expected number of regions may therefore not run on the model if they
are set up to run on real hardware.
Add properties mpu-ns-regions and mpu-s-regions to the ARMV7M object,
matching the ability of hardware to configure the number of Secure
and NonSecure regions separately. Our actual CPU implementation
doesn't currently support that, and it happens that none of the MPS
boards we model set the number of regions differently for Secure vs
NonSecure, so we provide an interface to the boards and SoCs that
won't need to change if we ever do add that functionality in future,
but make it an error to configure the two properties to different
values.
(The property name on the CPU is the somewhat misnamed-for-M-profile
"pmsav7-dregion", so we don't follow that naming convention for
the properties here. The TRM doesn't say what the CPU configuration
variable names are, so we pick something, and follow the lowercase
convention we already have for properties here.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230724174335.2150499-3-peter.maydell@linaro.org
The SRC device is normally used to start the secondary CPU.
When running Linux directly, QEMU is emulating a PSCI interface that UBOOT
is installing at boot time and therefore the fact that the SRC device is
unimplemented is hidden as Qemu respond directly to PSCI requets without
using the SRC device.
But if you try to run a more bare metal application (maybe uboot itself),
then it is not possible to start the secondary CPU as the SRC is an
unimplemented device.
This patch adds the ability to start the secondary CPU through the SRC
device so that you can use this feature in bare metal applications.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: ce9a0162defd2acee5dc7f8a674743de0cded569.1692964892.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Add TZASC as unimplemented device.
- Allow bare metal application to access this (unimplemented) device
* Add CSU as unimplemented device.
- Allow bare metal application to access this (unimplemented) device
* Add various memory segments
- OCRAM
- OCRAM EPDC
- OCRAM PXP
- OCRAM S
- ROM
- CAAM
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: f887a3483996ba06d40bd62ffdfb0ecf68621987.1692964892.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Add Addr and size definition for all i.MX7 devices in i.MX7 header file.
* Use those newly defined named constants whenever possible.
* Standardize the way we init a familly of unimplemented devices
- SAI
- PWM
- CAN
* Add/rework few comments
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 59e195d33e4d486a8d131392acd46633c8c10ed7.1692964892.git.jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Add TZASC as unimplemented device.
- Allow bare metal application to access this (unimplemented) device
* Add CSU as unimplemented device.
- Allow bare metal application to access this (unimplemented) device
* Add 4 missing PWM devices
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 59e4dc56e14eccfefd379275ec19048dff9c10b3.1692964892.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Add Addr and size definition for most i.MX6UL devices in i.MX6UL header file.
* Use those newly defined named constants whenever possible.
* Standardize the way we init a familly of unimplemented devices
- SAI
- PWM
- CAN
* Add/rework few comments
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: d579043fbd4e4b490370783fda43fc02c8e9be75.1692964892.git.jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
i.MX7 IOMUX GPR device is not equivalent to i.MX6UL IOMUXC GPR device.
In particular, register 22 is not present on i.MX6UL and this is actualy
The only register that is really emulated in the i.MX7 IOMUX GPR device.
Note: The i.MX6UL code is actually also implementing the IOMUX GPR device
as an unimplemented device at the same bus adress and the 2 instantiations
were actualy colliding. So we go back to the unimplemented device for now.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 48681bf51ee97646479bb261bee19abebbc8074e.1692964892.git.jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In order to use virtio backends we need to initialize RAM for the
xen-mapcache (which is responsible for mapping guest memory using foreign
mapping) to work. Calculate and add hi/low memory regions based on
machine->ram_size.
Use the constants defined in public header arch-arm.h to be aligned with the xen
toolstack.
While using this machine, the toolstack should then pass real ram_size using
"-m" arg. If "-m" is not given, create a QEMU machine without IOREQ and other
emulated devices like TPM and VIRTIO. This is done to keep this QEMU machine
usable for /etc/init.d/xencommons.
Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Signed-off-by: Vikram Garhwal <vikram.garhwal@amd.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <stefano.stabellini@amd.com>
In order to use virtio backends we need to allocate virtio-mmio
parameters (irq and base) and register corresponding buses.
Use the constants defined in public header arch-arm.h to be
aligned with the toolstack. So the number of current supported
virtio-mmio devices is 10.
For the interrupts triggering use already existing on Arm
device-model hypercall.
The toolstack should then insert the same amount of device nodes
into guest device-tree.
Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Signed-off-by: Vikram Garhwal <vikram.garhwal@amd.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <stefano.stabellini@amd.com>
On MIPS, kvm_arch_get_default_type() returns a negative value when an
error occurred so handle the case. Also, let other machines return
negative values when errors occur and declare returning a negative
value as the correct way to propagate an error that happened when
determining KVM type.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-id: 20230727073134.134102-5-akihiko.odaki@daynix.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Coverity points out (CID 1513106, 1513107) that MemoryListener is a
192 byte struct which we are passing around by value. Switch to
passing a const pointer into xen_register_ioreq() and then to
xen_do_ioreq_register(). We can also make the file-scope
MemoryListener variables const, since nothing changes them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230718101057.1110979-1-peter.maydell@linaro.org>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
The implementation of the SMMUv3 has multiple places where it reads a
data structure from the guest and directly operates on it without
doing a guest-to-host endianness conversion. Since all SMMU data
structures are little-endian, this means that the SMMU doesn't work
on a big-endian host. In particular, this causes the Avocado test
machine_aarch64_virt.py:Aarch64VirtMachine.test_alpine_virt_tcg_gic_max
to fail on an s390x host.
Add appropriate byte-swapping on reads and writes of guest in-memory
data structures so that the device works correctly on big-endian
hosts.
As part of this we constrain queue_read() to operate only on Cmd
structs and queue_write() on Evt structs, because in practice these
are the only data structures the two functions are used with, and we
need to know what the data structure is to be able to byte-swap its
parts correctly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20230717132641.764660-1-peter.maydell@linaro.org
Cc: qemu-stable@nongnu.org
This extends the slots of xhci to 64, since the default xhci_sysbus
just supports one slot.
Signed-off-by: Wang Yuquan <wangyuquan1236@phytium.com.cn>
Signed-off-by: Chen Baozi <chenbaozi@phytium.com.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Tested-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Message-id: 20230710063750.473510-2-wangyuquan1236@phytium.com.cn
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's use our new helper functions. Note that virtio-pmem-pci is not
enabled for arm and, therefore, not compiled in.
Message-ID: <20230711153445.514112-4-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's use our new helper. We'll add the subregion to system RAM now
earlier. That shouldn't matter, because the system RAM memory region should
already be alive at that point.
Cc: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230623124553.400585-4-david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
virt-acpi-build.c uses warn_report. However, it doesn't include
qemu/error-report.h directly, it include qemu/error-report.h via trace.h
if we enable log trace backend. But if we disable the log trace backend
(e.g., --enable-trace-backends=nop), then virt-acpi-build.c will not
include qemu/error-report.h any more and it will lead to build errors.
Include qemu/error-report.h directly in virt-acpi-build.c to avoid the
errors.
Fixes: 451b157041 ("acpi: Align the size to 128k")
Signed-off-by: Peng Liang <tcx4c70@gmail.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(mjt: move the #include higher as suggested by Ani Sinha)
pci_nic_init_nofail() calls qemu_find_nic_model(), and this function
sets nd->model = g_strdup(default_model) if it has not been initialized
yet. So we don't have to set nd->model to the default_nic in the
calling sites.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Now that we have implemented support for FEAT_LSE2, we can define
a CPU model for the Neoverse-V1, and enable it for the virt and
sbsa-ref boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230704130647.2842917-3-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The current sbsa-ref cannot use EHCI controller which is only
able to do 32-bit DMA, since sbsa-ref doesn't have RAM below 4GB.
Hence, this uses XHCI to provide a usb controller with 64-bit
DMA capablity instead of EHCI.
We bump the platform version to 0.3 with this change. Although the
hardware at the USB controller address changes, the firmware and
Linux can both cope with this -- on an older non-XHCI-aware
firmware/kernel setup the probe routine simply fails and the guest
proceeds without any USB. (This isn't a loss of functionality,
because the old USB controller never worked in the first place.) So
we can call this a backwards-compatible change and only bump the
minor version.
Signed-off-by: Yuquan Wang <wangyuquan1236@phytium.com.cn>
Message-id: 20230621103847.447508-2-wangyuquan1236@phytium.com.cn
[PMM: tweaked commit message; add line to docs about what
changes in platform version 0.3]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add MEMORY_LISTNER_PRIORITY_ACCEL for the symbolic value for the memory
listener to replace the hard-coded value 10 for accel.
No functional change intended.
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <feebe423becc6e2aa375f59f6abce9a85bc15abb.1687279702.git.isaku.yamahata@intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
"sysemu/kvm.h" is indirectly pulled in. Explicit its
inclusion to avoid when refactoring include/:
hw/arm/sbsa-ref.c:693:9: error: implicit declaration of function 'kvm_enabled' is invalid in C99 [-Werror,-Wimplicit-function-declaration]
if (kvm_enabled()) {
^
Reviewed-by: Leif Lindholm <quic_llindhol@quicinc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230405160454.97436-6-philmd@linaro.org>
"kvm_arm.h" contains external and internal prototype declarations.
Files under the hw/ directory should only access the KVM external
API.
In order to avoid machine / device models to include "kvm_arm.h"
simply to get the QOM GIC/ITS class name, un-inline each class
name getter to the proper device model file.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230405160454.97436-4-philmd@linaro.org>
There are two ARM machines where NUMA is aware: 'virt' and 'sbsa-ref'.
Both of them are required to follow cluster-NUMA-node boundary. To
enable the validation to warn about the irregular configuration where
multiple CPUs in one cluster have been associated with different NUMA
nodes.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230509002739.18388-3-gshan@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Create ITS as part of SBSA platform GIC initialization.
GIC ITS information is in DeviceTree so TF-A can pass it to EDK2.
Bumping platform version to 0.2 as this is important hardware change.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Message-id: 20230619170913.517373-2-marcin.juszkiewicz@linaro.org
Co-authored-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We use the user_ss[] array to hold the user emulation sources,
and the softmmu_ss[] array to hold the system emulation ones.
Hold the latter in the 'system_ss[]' array for parity with user
emulation.
Mechanical change doing:
$ sed -i -e s/softmmu_ss/system_ss/g $(git grep -l softmmu_ss)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230613133347.82210-10-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20230607092112.655098-1-marcin.juszkiewicz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----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=543t
-----END PGP SIGNATURE-----
Merge tag 'xenpvh5-tag' of https://gitlab.com/sstabellini/qemu into staging
xenpvh5
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCgAdFiEE0E4zq6UfZ7oH0wrqiU+PSHDhrpAFAmSLo0QACgkQiU+PSHDh
# rpB1Gw/9H5Cx7wQZVyKfFwnyOoP2QTedCISxC0HL5qFmUGcJY21gXaJZ10JaU/HM
# zHEJj2M17EgVCTkZVqZeKuj+nzyjbRKatT3YmFqKqFNNt5M1yQxC9BfVgso4PND/
# SY0/8BvqumgJEqD3sf76KbQAILKwahPtA42LTM7S7r2ZsmQpvmOpdOhCVugpnqs/
# FheP8N6hdlZ7GnRGtXv9QnKxMVThuE3mRCUWCyYsV/Roz6uvPsvskrdSeC3LzzBd
# Ewq56vB+qQg+WbNTgK2BcVOzV/89k9tjWsUnamfhjD2lUxfHrne1FBclhKMcHhUv
# T53zjhxjlRfmzUxC4917Krt4Tw/AaDW7v1pn6RokUq5U059Wb8q0IjzL75FOeD3o
# e9DNp+RR8py44ejfi2WHR7jqayMPVIO86uJ3usshiZ9YgK5efFAtlwN/KNR5JX8k
# Y1BR9O8BebtRymljtiLWUFXlu3xywGSA23KotT7XtzXKEaTZkIHdI395YKksYPkG
# pil0C0bh5ZW3ZWd4M/CNcVOb69R53p15O77mjmKtjnkQYJAPD6Kbc9thZ1zdWwPR
# ivFPdiTJb0FElS0ywZwezKYRKXje6E9ejXgAzgFuZI/rFdeO0HfkifiNoro1NAxK
# g4V+LE5oPt09GpL2nuHrh/y9g9MnLlXyNBhPV0CRelU6fPKIk1w=
# =543t
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 16 Jun 2023 01:48:20 AM CEST
# gpg: using RSA key D04E33ABA51F67BA07D30AEA894F8F4870E1AE90
# gpg: Good signature from "Stefano Stabellini <sstabellini@kernel.org>" [unknown]
# gpg: aka "Stefano Stabellini <stefano.stabellini@eu.citrix.com>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: D04E 33AB A51F 67BA 07D3 0AEA 894F 8F48 70E1 AE90
* tag 'xenpvh5-tag' of https://gitlab.com/sstabellini/qemu:
test/qtest: add xepvh to skip list for qtest
meson.build: enable xenpv machine build for ARM
hw/arm: introduce xenpvh machine
meson.build: do not set have_xen_pci_passthrough for aarch64 targets
hw/xen/xen-hvm-common: Use g_new and error_report
hw/xen/xen-hvm-common: skip ioreq creation on ioreq registration failure
include/hw/xen/xen_common: return error from xen_create_ioreq_server
xen-hvm: reorganize xen-hvm and move common function to xen-hvm-common
hw/i386/xen/xen-hvm: move x86-specific fields out of XenIOState
hw/i386/xen: rearrange xen_hvm_init_pc
hw/i386/xen/: move xen-mapcache.c to hw/xen/
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add a new machine xenpvh which creates a IOREQ server to register/connect with
Xen Hypervisor.
Optional: When CONFIG_TPM is enabled, it also creates a tpm-tis-device, adds a
TPM emulator and connects to swtpm running on host machine via chardev socket
and support TPM functionalities for a guest domain.
Extra command line for aarch64 xenpvh QEMU to connect to swtpm:
-chardev socket,id=chrtpm,path=/tmp/myvtpm2/swtpm-sock \
-tpmdev emulator,id=tpm0,chardev=chrtpm \
-machine tpm-base-addr=0x0c000000 \
swtpm implements a TPM software emulator(TPM 1.2 & TPM 2) built on libtpms and
provides access to TPM functionality over socket, chardev and CUSE interface.
Github repo: https://github.com/stefanberger/swtpm
Example for starting swtpm on host machine:
mkdir /tmp/vtpm2
swtpm socket --tpmstate dir=/tmp/vtpm2 \
--ctrl type=unixio,path=/tmp/vtpm2/swtpm-sock &
Signed-off-by: Vikram Garhwal <vikram.garhwal@amd.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@amd.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Cortex A7 CPUs with an FPU implementing VFPv4 without NEON support
have 16 64-bit FPU registers and not 32 registers. Let users set the
number of VFP registers with a CPU property.
The primary use case of this property is for the Cortex A7 of the
Aspeed AST2600 SoC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Most of the Aspeed machines use the UART5 device for the boot console,
and QEMU connects the first serial Chardev to this SoC device for this
purpose. See routine connect_serial_hds_to_uarts().
Nevertheless, some machines use another boot console, such as the fuji,
and commit 5d63d0c76c ("hw/arm/aspeed: Allow machine to set UART
default") introduced a SoC class attribute 'uart_default' and property
to be able to change the boot console device. It was later changed by
commit d2b3eaefb4 ("aspeed: Refactor UART init for multi-SoC machines").
The "bmc-console" machine option goes a step further and lets the user define
the UART device from the QEMU command line without introducing a new
machine definition. For instance, to use device UART3 (mapped on
/dev/ttyS2 under Linux) instead of the default UART5, one would use :
-M ast2500-evb,bmc-console=uart3
Cc: Abhishek Singh Dagur <abhishek@drut.io>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This change completes commits 5aa281d757 ("aspeed: Introduce a
spi_boot region under the SoC") and 8b744a6a47 ("aspeed: Add a
boot_rom overlap region in the SoC spi_boot container") which
introduced a spi_boot container at the SoC level to map the boot rom
region as an overlap.
It also fixes a Coverity report (CID 1508061) for a memory leak
warning when the QEMU process exits by using an bmc_boot_rom
MemoryRegion available at the machine level.
Cc: Peter Delevoryas <peter@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This should also avoid Coverity to report a memory leak warning when
the QEMU process exits. See CID 1508061.
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The current modeling of Rainier machine creates zero filled VPDs(EEPROMs).
This makes some services and applications unhappy and causing them to fail.
Hence this drop adds some fabricated data for system and BMC FRU so that
vpd services are happy and active.
Tested:
- The system-vpd.service is active.
- VPD service related to bmc is active.
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: commit title cleanup ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
