Add support for stripping/inserting VLAN for VFs.
Had to move CSUM calculation back into the for loop, since packet data
is pulled inside the loop based on strip VLAN decision for every VF.
net_rx_pkt_fix_l4_csum should be extended to accept a buffer instead for
igb. Work for a future patch.
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Please note that loopback counters for VM to VM traffic is not
implemented yet: VFGOTLBC, VFGPTLBC, VFGORLBC and VFGPRLBC.
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
RSS for VFs is only enabled if VMOLR[n].RSSE is set.
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
IGB uses RXDW ICR bit to indicate that rx descriptor has been written
back. This is the same as RXT0 bit in older HW.
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Use PFRSTD to reset RSTI bit for VFs, and raise VFLRE interrupt when VF
is reset.
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Align the l3_hdr member of NetTxPkt by defining it as a union of
ip_header, ip6_header, and an array of octets.
Fixes: e263cd49c7 ("Packet abstraction for VMWARE network devices")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1544
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
No segmentation should be performed if gso type is
VIRTIO_NET_HDR_GSO_NONE even if ECN bit is set.
Fixes: e263cd49c7 ("Packet abstraction for VMWARE network devices")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1544
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
igb used to specify the PF as DMA requester when reading Tx packets.
This made Tx requests from VFs to be performed on the address space of
the PF, defeating the purpose of SR-IOV. Add some logic to change the
requester depending on the queue, which can be assigned to a VF.
Fixes: 3a977deebe ("Intrdocue igb device emulation")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The current implementation of igb uses only part of a advanced Tx
context descriptor and first data descriptor because it misses some
features and sniffs the trait of the packet instead of respecting the
packet type specified in the descriptor. However, we will certainly
need the entire Tx context descriptor when we update igb to respect
these ignored fields. Save the entire context descriptor and first
data descriptor except the buffer address to prepare for such a change.
This also introduces the distinction of contexts with different
indexes, which was not present in e1000e but in igb.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This change introduces emulation for the Intel 82576 adapter, AKA igb.
The details of the device will be provided by the documentation that
will follow this change.
This initial implementation of igb does not cover the full feature set,
but it selectively implements changes necessary to pass tests of Linut
Test Project, and Windows HLK. The below is the list of the implemented
changes; anything not listed here is not implemented:
New features:
- igb advanced descriptor handling
- Support of 16 queues
- SRRCTL.BSIZEPACKET register field
- SRRCTL.RDMTS register field
- Tx descriptor completion writeback
- Extended RA registers
- VMDq feature
- MRQC "Multiple Receive Queues Enable" register field
- DTXSWC.Loopback_en register field
- VMOLR.ROMPE register field
- VMOLR.AUPE register field
- VLVF.VLAN_id register field
- VLVF.VI_En register field
- VF
- Mailbox
- Reset
- Extended interrupt registers
- Default values for IGP01E1000 PHY registers
Removed features:
- e1000e extended descriptor
- e1000e packet split descriptor
- Legacy descriptor
- PHY register paging
- MAC Registers
- Legacy interrupt timer registers
- Legacy EEPROM registers
- PBA/POEM registers
- RSRPD register
- RFCTL.ACKDIS
- RCTL.DTYPE
- Copper PHY registers
Misc:
- VET register format
- ICR register format
Signed-off-by: Gal Hammer <gal.hammer@sap.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
[Jason: don't abort on msi(x)_init()]
Signed-off-by: Jason Wang <jasowang@redhat.com>
Some definitions in the header files are invalid for igb so extract
them to new header files to keep igb from referring to them.
Signed-off-by: Gal Hammer <gal.hammer@sap.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
igb, a new network device emulation, will need SCTP checksum offloading.
Currently eth_get_protocols() has a bool parameter for each protocol
currently it supports, but there will be a bit too many parameters if
we add yet another protocol.
Introduce an enum type, EthL4HdrProto to represent all L4 protocols
eth_get_protocols() support with one parameter.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The system clock is necessary to implement PTP features. While we are
not implementing PTP features for e1000e yet, we do have a plan to
implement them for igb, a new network device derived from e1000e,
so add system clock to the common base first.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The values returned by eth_get_protocols() are used to perform RSS,
checksumming and segmentation. Even when a packet signals the use of the
protocols which these operations can be applied to, the headers for them
may not be present because of too short packet or fragmentation, for
example. In such a case, the operations cannot be applied safely.
Report the presence of headers instead of whether the use of the
protocols are indicated with eth_get_protocols(). This also makes
corresponding changes to the callers of eth_get_protocols() to match
with its new signature and to remove redundant checks for fragmentation.
Fixes: 75020a7021 ("Common definitions for VMWARE devices")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The datasheet 8.19.29 "Good Packets Transmitted Count - GPTC (0x04080;
RC)" says:
> This register counts the number of good (no errors) packets
> transmitted. A good transmit packet is considered one that is 64 or
> more bytes in length (from <Destination Address> through <CRC>,
> inclusively) in length.
It also says similar for the other Tx statistics registers. Add the
number of bytes for CRC to those registers.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The Software Developer's Manual 13.7.4.5 "Packets Transmitted (64 Bytes)
Count" says:
> This register counts the number of packets transmitted that are
> exactly 64 bytes (from <Destination Address> through <CRC>,
> inclusively) in length.
It also says similar for the other Tx statistics registers. Add the
number of bytes for CRC to those registers.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Whether a packet will be written back to the guest depends on the
remaining space of the queue. Therefore, e1000e_rx_written_to_guest and
e1000e_rx_not_written_to_guest should log the index of the queue instead
of generated interrupts. This also removes the need of
e1000e_rx_rss_dispatched_to_queue, which logs the queue index.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Assertions will fail if MSI-X gets disabled while a timer for MSI-X
interrupts is running so remove them to avoid abortions. Fortunately,
nothing bad happens even if the assertions won't trigger as
msix_notify(), called by timer handlers, does nothing when MSI-X is
disabled.
This bug was found by Alexander Bulekov when fuzzing igb, a new
device implementation derived from e1000e:
https://patchew.org/QEMU/20230129053316.1071513-1-alxndr@bu.edu/
The fixed test case is:
fuzz/crash_aea040166819193cf9fedb810c6d100221da721a
Fixes: 6f3fbe4ed0 ("net: Introduce e1000e device emulation")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Check the payload length if checksumming to ensure the payload contains
the space for the resulting value.
This bug was found by Alexander Bulekov with the fuzzer:
https://patchew.org/QEMU/20230129053316.1071513-1-alxndr@bu.edu/
The fixed test case is:
fuzz/crash_6aeaa33e7211ecd603726c53e834df4c6d1e08bc
Fixes: e263cd49c7 ("Packet abstraction for VMWARE network devices")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
There was no proper implementation of TCP segmentation before this
change, and net_tx_pkt relied solely on IPv4 fragmentation. Not only
this is not aligned with the specification, but it also resulted in
corrupted IPv6 packets.
This is particularly problematic for the igb, a new proposed device
implementation; igb provides loopback feature for VMDq and the feature
relies on software segmentation.
Implement proper TCP segmentation in net_tx_pkt to fix such a scenario.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
e1000e didn't perform software segmentation for loopback if virtio-net
header is enabled, which is wrong.
To fix the problem, introduce net_tx_pkt_send_custom(), which allows the
caller to specify whether offloading should be assumed or not.
net_tx_pkt_send_custom() also allows the caller to provide a custom
sending function. Packets with virtio-net headers and ones without
virtio-net headers will be provided at the same time so the function
can choose the preferred version. In case of e1000e loopback, it prefers
to have virtio-net headers as they allows to skip the checksum
verification if VIRTIO_NET_HDR_F_DATA_VALID is set.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
When virtio-net header is not set, net_rx_pkt_get_vhdr() returns
zero-filled virtio_net_hdr, which is actually valid. In fact, tap device
uses zero-filled virtio_net_hdr when virtio-net header is not provided
by the peer. Therefore, we can just remove net_rx_pkt_has_virt_hdr() and
always assume NetTxPkt has a valid virtio-net header.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The new function qemu_get_using_vnet_hdr() allows to automatically
determine if virtio-net header is used.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
e1000x_is_vlan_packet() had a pointer to uint8_t as a parameter, but
it does not have to be uint8_t. Change the type to void *.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
net_tx_pkt_build_vheader() inspects TCP header but had no check for
the header size, resulting in an undefined behavior. Check the header
size and drop the packet if the header is too small.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
e1000e_write_packet_to_guest() passes the reference of variable ba as a
pointer to an array, and that pointer indirection is just unnecessary;
all functions which uses the passed reference performs no pointer
operation on the pointer and they simply dereference the passed
pointer. Remove the extra pointer indirection.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This keeps Windows driver 12.18.9.23 from generating an event with ID
30. The description of the event is as follows:
> Intel(R) 82574L Gigabit Network Connection
> PROBLEM: The network adapter is configured for auto-negotiation but
> the link partner is not. This may result in a duplex mismatch.
> ACTION: Configure the link partner for auto-negotiation.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Before this change, e1000e_write_packet_to_guest() allocated the
receive descriptor buffer as an array of uint8_t. This does not ensure
the buffer is sufficiently aligned.
Introduce e1000_rx_desc_union type, a union type of all receive
descriptor types to correct this.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This is part of recent efforts of refactoring e1000 and e1000e.
DeviceClass's reset member is deprecated so migrate to ResettableClass.
There is no behavioral difference.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This is part of recent efforts of refactoring e1000 and e1000e.
DeviceClass's reset member is deprecated so migrate to ResettableClass.
There is no behavioral difference.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This change makes e1000e reset more things when software reset was
triggered. Some registers are exempted from software reset in the
datasheet and this change also implements the behavior accordingly.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
They are duplicate of running throttling timer flags and incomplete as
the flags are not cleared when the interrupts are fired or the device is
reset.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Use memcpy instead of memmove to initialize registers. The initial
register templates and register table instances will never overlap.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Use memcpy instead of memmove to initialize registers. The initial
register templates and register table instances will never overlap.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
When a register has effective bits fewer than their width, the old code
inconsistently masked when writing or reading. Make the code consistent
by always masking when writing, and remove some code duplication.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
e1000e_set_16bit and e1000e_set_12bit look so similar so define a
generic macro.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
When a register has effective bits fewer than their width, the old code
inconsistently masked when writing or reading. Make the code consistent
by always masking when writing, and remove some code duplication.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
hw/net/mii.h provides common definitions for MII.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
hw/net/mii.h provides common definitions for MII.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
igb implementation first starts off by copying e1000e code. Correct the
code style before that.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
XC_PAGE_SIZE comes from the actual Xen libraries, while XEN_PAGE_SIZE is
provided by QEMU itself in xen_backend_ops.h. For backends which may be
built for emulation mode, use the latter.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
The previous commit introduced redirectable gnttab operations fairly
much like-for-like, with the exception of the extra arguments to the
->open() call which were always NULL/0 anyway.
This *changes* the arguments to the ->unmap() operation to include the
original ref# that was mapped. Under real Xen it isn't necessary; all we
need to do from QEMU is munmap(), then the kernel will release the grant,
and Xen does the tracking/refcounting for the guest.
When we have emulated grant tables though, we need to do all that for
ourselves. So let's have the back ends keep track of what they mapped
and pass it in to the ->unmap() method for us.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Since GUEST_ANNOUNCE is emulated the feature bit could be set without
backend support. This happens in the vDPA case.
However, backend vDPA parent may not have CVQ support. This causes an
incoherent feature set, and the driver may refuse to start. This
happens in virtio-net Linux driver.
This may be solved differently in the future. Qemu is able to emulate a
CVQ just for guest_announce purposes, helping guest to notify the new
location with vDPA devices that does not support it. However, this is
left as a TODO as it is way more complex to backport.
Tested with vdpa_net_sim, toggling manually VIRTIO_NET_F_CTRL_VQ in the
driver and migrating it with x-svq=on.
Fixes: 980003debd ("vdpa: do not handle VIRTIO_NET_F_GUEST_ANNOUNCE in vhost-vdpa")
Reported-by: Dawar, Gautam <gautam.dawar@amd.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20230124161159.2182117-1-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Reviewed-by: Gautam Dawar <gautam.dawar@amd.com>
Tested-by: Gautam Dawar <gautam.dawar@amd.com>
Tested-by: Lei Yang <leiyang@redhat.com>
The QERR_ macros are leftovers from the days of "rich" error objects.
We've been trying to reduce their remaining use.
The stubbed out Rocker monitor commands are the last remaining users
of QERR_FEATURE_DISABLED. They fail like this:
(qemu) info rocker mumble
Error: The feature 'rocker' is not enabled
The real rocker commands fail like this when the named object doesn't
exist:
Error: rocker mumble not found
If that's good enough when Rocker is enabled, then it's good enough
when it's disabled, so replace QERR_FEATURE_DISABLED with that, and
drop the macro.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20230207075115.1525-13-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Currently, VMXNET3_MAX_MTU itself (being 9000) is not considered a
valid value for the MTU, but a guest running ESXi 7.0 might try to
set it and fail the assert [0].
In the Linux kernel, dev->max_mtu itself is a valid value for the MTU
and for the vmxnet3 driver it's 9000, so a guest running Linux will
also fail the assert when trying to set an MTU of 9000.
VMXNET3_MAX_MTU and s->mtu don't seem to be used in relation to buffer
allocations/accesses, so allowing the upper limit itself as a value
should be fine.
[0]: https://forum.proxmox.com/threads/114011/
Fixes: d05dcd94ae ("net: vmxnet3: validate configuration values during activate (CVE-2021-20203)")
Signed-off-by: Fiona Ebner <f.ebner@proxmox.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch replaces hw_error to guest error log for [read|write]b
accesses when mode_16bit is enabled. This avoids aborting qemu.
Fixes: 1248f8d4cb ("hw/lan9118: Add basic 16-bit mode support.")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1433
Reported-by: Qiang Liu <cyruscyliu@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Qiang Liu <cyruscyliu@gmail.com>
Suggested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Tracked down with the help of scripts/clean-includes.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20230202133830.2152150-21-armbru@redhat.com>
With the `size += 4` before the call to `crc32`, the CRC calculation
would overrun the buffer. Size is used in the while loop starting on
line 1009 to determine how much data to write back, with the last
four bytes coming from `crc_ptr`, so do need to increase it, but should
do this after the computation.
I'm unsure why this use of uninitialized memory in the CRC doesn't
result in CRC errors, but it seems clear to me that it should not be
included in the calculation.
Signed-off-by: Stephen Longfield <slongfield@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20221220221437.3303721-1-slongfield@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This moves these commands from MAINTAINERS section "Human
Monitor (HMP)" to "Rocker" and "Network devices".
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20230124121946.1139465-14-armbru@redhat.com>
The 'hwaddr' type is defined in "exec/hwaddr.h" as:
hwaddr is the type of a physical address
(its size can be different from 'target_ulong').
All definitions use the 'HWADDR_' prefix, except TARGET_FMT_plx:
$ fgrep define include/exec/hwaddr.h
#define HWADDR_H
#define HWADDR_BITS 64
#define HWADDR_MAX UINT64_MAX
#define TARGET_FMT_plx "%016" PRIx64
^^^^^^
#define HWADDR_PRId PRId64
#define HWADDR_PRIi PRIi64
#define HWADDR_PRIo PRIo64
#define HWADDR_PRIu PRIu64
#define HWADDR_PRIx PRIx64
#define HWADDR_PRIX PRIX64
Since hwaddr's size can be *different* from target_ulong, it is
very confusing to read one of its format using the 'TARGET_FMT_'
prefix, normally used for the target_long / target_ulong types:
$ fgrep TARGET_FMT_ include/exec/cpu-defs.h
#define TARGET_FMT_lx "%08x"
#define TARGET_FMT_ld "%d"
#define TARGET_FMT_lu "%u"
#define TARGET_FMT_lx "%016" PRIx64
#define TARGET_FMT_ld "%" PRId64
#define TARGET_FMT_lu "%" PRIu64
Apparently this format was missed during commit a8170e5e97
("Rename target_phys_addr_t to hwaddr"), so complete it by
doing a bulk-rename with:
$ sed -i -e s/TARGET_FMT_plx/HWADDR_FMT_plx/g $(git grep -l TARGET_FMT_plx)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230110212947.34557-1-philmd@linaro.org>
[thuth: Fix some warnings from checkpatch.pl along the way]
Signed-off-by: Thomas Huth <thuth@redhat.com>
PCIDeviceClass and PCIDevice are defined in pci.h. Many users of the
header don't actually need them. Similar structs live in their own
headers: PCIBusClass and PCIBus in pci_bus.h, PCIBridge in
pci_bridge.h, PCIHostBridgeClass and PCIHostState in pci_host.h,
PCIExpressHost in pcie_host.h, and PCIERootPortClass, PCIEPort, and
PCIESlot in pcie_port.h.
Move PCIDeviceClass and PCIDeviceClass to new pci_device.h, along with
the code that needs them. Adjust include directives.
This also enables the next commit.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221222100330.380143-6-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add functions to support configure interrupt in virtio_net
Add the functions to support vhost_net_config_pending
and vhost_net_config_mask.
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20221222070451.936503-9-lulu@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To support configure interrupt for vhost-vdpa
Introduce VIRTIO_CONFIG_IRQ_IDX -1 as configure interrupt's queue index,
Then we can reuse the functions guest_notifier_mask and guest_notifier_pending.
Add the check of queue index in these drivers, if the driver does not support
configure interrupt, the function will just return
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20221222070451.936503-2-lulu@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch aims to fix unexpected negotiation features for
vhost-user netdev interface.
When openvswitch reconnect Qemu after an unexpected disconnection
and Qemu therefore start the vhost_dev, acked_features field in
vhost_dev is initialized with value fetched from acked_features
field in NetVhostUserState, which should be up-to-date at that
moment but Qemu could not make it actually during the time window
of virtio features negotiation.
So we save the acked_features right after being configured by
guest virtio driver so it can be used to restore acked_features
field in vhost_dev correctly.
Signed-off-by: Hyman Huang(黄勇) <huangy81@chinatelecom.cn>
Signed-off-by: Guoyi Tu <tugy@chinatelecom.cn>
Signed-off-by: Liuxiangdong <liuxiangdong5@huawei.com>
Message-Id: <b9f8cf5561a79ea65ea38960e5a5e6d3707eef0a.1671627406.git.huangy81@chinatelecom.cn>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Status part of the emulated feature. It will follow device model, so we
must copy it as long as NIC device model has it set.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20221221115015.1400889-3-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Next patches introduce more code on vhost-vdpa branch, with already have
too much indentation.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221221115015.1400889-2-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Size is used at lines 1088/1188 for the loop, which reads the last 4
bytes from the crc_ptr so it does need to get increased, however it
shouldn't be increased before the buffer is passed to CRC computation,
or the crc32 function will access uninitialized memory.
This was pointed out to me by clg@kaod.org during the code review of
a similar patch to hw/net/ftgmac100.c
Change-Id: Ib0464303b191af1e28abeb2f5105eb25aadb5e9b
Signed-off-by: Stephen Longfield <slongfield@google.com>
Reviewed-by: Patrick Venture <venture@google.com>
Message-id: 20221221183202.3788132-1-slongfield@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It seems a little bit weird that the para-virtualized x86 VMWare
devices "vmware-svga" and "vmxnet3" also show up in non-x86 targets.
They are likely pretty useless there (since the guest OSes likely
do not have any drivers for those enabled), so let's change this and
only enable those devices by default for the classical x86 targets.
Message-Id: <20221213095144.42355-1-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
-----BEGIN PGP SIGNATURE-----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=JJjG
-----END PGP SIGNATURE-----
Merge tag 'pull-misc-2022-12-14' of https://repo.or.cz/qemu/armbru into staging
Miscellaneous patches for 2022-12-14
# gpg: Signature made Wed 14 Dec 2022 15:23:02 GMT
# gpg: using RSA key 354BC8B3D7EB2A6B68674E5F3870B400EB918653
# gpg: issuer "armbru@redhat.com"
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>" [full]
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>" [full]
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* tag 'pull-misc-2022-12-14' of https://repo.or.cz/qemu/armbru:
ppc4xx_sdram: Simplify sdram_ddr_size() to return
block/vmdk: Simplify vmdk_co_create() to return directly
cleanup: Tweak and re-run return_directly.cocci
io: Tidy up fat-fingered parameter name
qapi: Use returned bool to check for failure (again)
sockets: Use ERRP_GUARD() where obviously appropriate
qemu-config: Use ERRP_GUARD() where obviously appropriate
qemu-config: Make config_parse_qdict() return bool
monitor: Use ERRP_GUARD() in monitor_init()
monitor: Simplify monitor_fd_param()'s error handling
error: Move ERRP_GUARD() to the beginning of the function
error: Drop a few superfluous ERRP_GUARD()
error: Drop some obviously superfluous error_propagate()
Drop more useless casts from void * to pointer
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/rocker.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221104160712.3005652-23-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/net.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221104160712.3005652-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
[Fixes for MacOS squashed in]
Fixes regression with migration and vsock, as fixing that
exposes some known issues in vhost user cleanup, this attempts
to fix those as well. More work on vhost user is needed :)
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmOIWaEPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRp+RQH/2PVAjD/GA3zF5F3Z07vH51c55T6tluZ85c3
4u66SSkF5JR1hATCujYCtrt9V0mnqhmhhm4gJH5xcsynFjjyIXd2dDrTFRpCtRgn
icXOmYCc9pCu8XsluJnWvY/5r/KEDxqmGVE8Kyhz551QjvsBkezhI9x9vhJZJLCn
Xn1XQ/3jpUcQLwasu8AxZb0IDW8WdCtonbke6xIyMzOYGR2bnRdXlDXVVG1zJ/SZ
eS3HUad71VekhfzWq0fx8yEJnfvbes9vo007y8rOGdHOcMneWGAie52W1dOBhclh
Zt56zID55t1USEwlPxkZSj7UXNbVl7Uz/XU5ElN0yTesttP4Iq0=
=ZkaX
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio: regression fix
Fixes regression with migration and vsock, as fixing that
exposes some known issues in vhost user cleanup, this attempts
to fix those as well. More work on vhost user is needed :)
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmOIWaEPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRp+RQH/2PVAjD/GA3zF5F3Z07vH51c55T6tluZ85c3
# 4u66SSkF5JR1hATCujYCtrt9V0mnqhmhhm4gJH5xcsynFjjyIXd2dDrTFRpCtRgn
# icXOmYCc9pCu8XsluJnWvY/5r/KEDxqmGVE8Kyhz551QjvsBkezhI9x9vhJZJLCn
# Xn1XQ/3jpUcQLwasu8AxZb0IDW8WdCtonbke6xIyMzOYGR2bnRdXlDXVVG1zJ/SZ
# eS3HUad71VekhfzWq0fx8yEJnfvbes9vo007y8rOGdHOcMneWGAie52W1dOBhclh
# Zt56zID55t1USEwlPxkZSj7UXNbVl7Uz/XU5ElN0yTesttP4Iq0=
# =ZkaX
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 01 Dec 2022 02:37:05 EST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu:
include/hw: VM state takes precedence in virtio_device_should_start
hw/virtio: generalise CHR_EVENT_CLOSED handling
hw/virtio: add started_vu status field to vhost-user-gpio
vhost: enable vrings in vhost_dev_start() for vhost-user devices
tests/qtests: override "force-legacy" for gpio virtio-mmio tests
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Commit 02b61f38d3 ("hw/virtio: incorporate backend features in features")
properly negotiates VHOST_USER_F_PROTOCOL_FEATURES with the vhost-user
backend, but we forgot to enable vrings as specified in
docs/interop/vhost-user.rst:
If ``VHOST_USER_F_PROTOCOL_FEATURES`` has not been negotiated, the
ring starts directly in the enabled state.
If ``VHOST_USER_F_PROTOCOL_FEATURES`` has been negotiated, the ring is
initialized in a disabled state and is enabled by
``VHOST_USER_SET_VRING_ENABLE`` with parameter 1.
Some vhost-user front-ends already did this by calling
vhost_ops.vhost_set_vring_enable() directly:
- backends/cryptodev-vhost.c
- hw/net/virtio-net.c
- hw/virtio/vhost-user-gpio.c
But most didn't do that, so we would leave the vrings disabled and some
backends would not work. We observed this issue with the rust version of
virtiofsd [1], which uses the event loop [2] provided by the
vhost-user-backend crate where requests are not processed if vring is
not enabled.
Let's fix this issue by enabling the vrings in vhost_dev_start() for
vhost-user front-ends that don't already do this directly. Same thing
also in vhost_dev_stop() where we disable vrings.
[1] https://gitlab.com/virtio-fs/virtiofsd
[2] https://github.com/rust-vmm/vhost/blob/240fc2966/crates/vhost-user-backend/src/event_loop.rs#L217
Fixes: 02b61f38d3 ("hw/virtio: incorporate backend features in features")
Reported-by: German Maglione <gmaglione@redhat.com>
Tested-by: German Maglione <gmaglione@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20221123131630.52020-1-sgarzare@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20221130112439.2527228-3-alex.bennee@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
fixes regressions:
virtio error message triggered by seabios
failure in vhost due to VIRTIO_F_RING_RESET
broken keyboard under seabios
some biosbits test fixes
there's still a known regression with migration and vsock,
not fixed yet.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmN8os4PHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpw+UH/2JOoxqzkkq4QyV5PzmjsiyyMbrBqFSOTro2
98k9MwxNWHIk6fi3FVIz+LX1EdwDbMl44IHQ88xo7k39V7ThvVvLfjaQySSeoCfE
04++AvkOQ/O8W7sob17r2iPWIHKPIndq8uB652T89o1I/nhmFMsUkdRWmVQ3XsDk
DnPZxjBQnKY0oSvBd7SmSI3C+eA4lF1tht50ZxmOshLx4OSjK/maFVpIyLsUGTMn
6OMxKffDjfvw5z94+pGN1RQm9xu7OwtFZyUnH16xoQUmWSXjzcYXUZ3buTY+eAyJ
I5j9ox27Cqn1wGcypUiTCKLIExEMBfvNY4ovyRa1xvW+MXluVyE=
=bF2U
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
pc,virtio: regression, test fixes
fixes regressions:
virtio error message triggered by seabios
failure in vhost due to VIRTIO_F_RING_RESET
broken keyboard under seabios
some biosbits test fixes
there's still a known regression with migration and vsock,
not fixed yet.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmN8os4PHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRpw+UH/2JOoxqzkkq4QyV5PzmjsiyyMbrBqFSOTro2
# 98k9MwxNWHIk6fi3FVIz+LX1EdwDbMl44IHQ88xo7k39V7ThvVvLfjaQySSeoCfE
# 04++AvkOQ/O8W7sob17r2iPWIHKPIndq8uB652T89o1I/nhmFMsUkdRWmVQ3XsDk
# DnPZxjBQnKY0oSvBd7SmSI3C+eA4lF1tht50ZxmOshLx4OSjK/maFVpIyLsUGTMn
# 6OMxKffDjfvw5z94+pGN1RQm9xu7OwtFZyUnH16xoQUmWSXjzcYXUZ3buTY+eAyJ
# I5j9ox27Cqn1wGcypUiTCKLIExEMBfvNY4ovyRa1xvW+MXluVyE=
# =bF2U
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 22 Nov 2022 05:22:06 EST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu:
virtio: disable error for out of spec queue-enable
acpi/tests/avocado/bits: keep the work directory when BITS_DEBUG is set in env
tests/avocado: configure acpi-bits to use avocado timeout
MAINTAINERS: add mst to list of biosbits maintainers
tests: acpi: x86: update expected DSDT after moving PRQx fields in _SB scope
acpi: x86: move RPQx field back to _SB scope
tests: acpi: whitelist DSDT before moving PRQx to _SB scope
vhost: mask VIRTIO_F_RING_RESET for vhost and vhost-user devices
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Commit 69e1c14aa2 ("virtio: core: vq reset feature negotation support")
enabled VIRTIO_F_RING_RESET by default for all virtio devices.
This feature is not currently emulated by QEMU, so for vhost and
vhost-user devices we need to make sure it is supported by the offloaded
device emulation (in-kernel or in another process).
To do this we need to add VIRTIO_F_RING_RESET to the features bitmap
passed to vhost_get_features(). This way it will be masked if the device
does not support it.
This issue was initially discovered with vhost-vsock and vhost-user-vsock,
and then also tested with vhost-user-rng which confirmed the same issue.
They fail when sending features through VHOST_SET_FEATURES ioctl or
VHOST_USER_SET_FEATURES message, since VIRTIO_F_RING_RESET is negotiated
by the guest (Linux >= v6.0), but not supported by the device.
Fixes: 69e1c14aa2 ("virtio: core: vq reset feature negotation support")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1318
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20221121101101.29400-1-sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Acked-by: Jason Wang <jasowang@redhat.com>
The Large-Send Task Offload Tx Descriptor (9.2.1 Transmit) has a
Large-Send MSS value where the driver specifies the MSS. See the
datasheet here:
http://realtek.info/pdf/rtl8139cp.pdf
The code ignores this value and uses a hardcoded MSS of 1500 bytes
instead. When the MTU is less than 1500 bytes the hardcoded value
results in IP fragmentation and poor performance.
Use the Large-Send MSS value to correctly size Large-Send packets.
Jason Wang <jasowang@redhat.com> noticed that the Large-Send MSS value
mask was incorrect so it is adjusted to match the datasheet and Linux
8139cp driver.
This issue was discussed in the past here:
https://lore.kernel.org/all/20161114162505.GD26664@stefanha-x1.localdomain/
Reported-by: Russell King - ARM Linux <linux@armlinux.org.uk>
Reported-by: Tobias Fiebig <tobias+git@fiebig.nl>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1312
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20221117165554.1773409-4-stefanha@redhat.com>
There are two Tx Descriptor formats called mode 0 and mode 1. The mode
is determined by the Large Send bit.
CP_TX_IPCS (bit 18) is defined in mode 1 but the code checks the bit
unconditionally. In mode 0 bit 18 is part of the Large Send MSS value.
Explicitly check the Large Send bit to distinguish Tx command modes.
This avoids bugs where modes are confused. Note that I didn't find any
actual bugs aside from needlessly computing the IP checksum when the
Large Send bit is enabled.
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20221117165554.1773409-3-stefanha@redhat.com>
The device turns the Tx Descriptor into a Tx Status descriptor after
fully reading the descriptor. This involves clearing Tx Own (bit 31) to
indicate that the driver has ownership of the descriptor again as well
as several other bits.
The code keeps the first dword of the Tx Descriptor in the txdw0 local
variable. txdw0 is reused to build the first word of the Tx Status
descriptor. Later on the code uses txdw0 again, incorrectly assuming
that it still contains the first dword of the Tx Descriptor. The tx
offloading code misbehaves because it sees bogus bits in txdw0.
Use a separate local variable for Tx Status and preserve Tx Descriptor
in txdw0.
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20221117165554.1773409-2-stefanha@redhat.com>
Replaces TABs with spaces, making sure to have a consistent coding style
of 4 space indentations in the net subsystem.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/377
Signed-off-by: Ahmed Abouzied <email@aabouzied.com>
Message-Id: <20210614183849.20622-1-email@aabouzied.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[thuth: Fixed mis-aligned indentation in some of the files]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Variable n used in tulip_idblock_crc function is only incremented but never read.
This causes 'Unused but set variable' warning on Clang 15.0.1 compiler.
Removing the variable to prevent the warning.
Signed-off-by: Miroslav Rezanina <mrezanin@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <02e1560d115c208df32236df8916fed98429fda1.1668009030.git.mrezanin@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Variable send_count used in rtl8139_cplus_transmit_one function is only
incremented but never read. This causes 'Unused but set variable' warning
on Clang 15.0.1 compiler.
Removing the variable to prevent the warning.
Signed-off-by: Miroslav Rezanina <mrezanin@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <15a32dd06c492216cbf27cd3ddcbe1e9afb8d8f5.1668009030.git.mrezanin@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Run shell script:
cat << EOF | valgrind qemu-system-i386 -display none -machine accel=qtest, -m \
512M -M q35 -nodefaults -device virtio-net,netdev=net0 -netdev \
user,id=net0 -qtest stdio
outl 0xcf8 0x80000810
outl 0xcfc 0xc000
outl 0xcf8 0x80000804
outl 0xcfc 0x01
outl 0xc00d 0x0200
outl 0xcf8 0x80000890
outb 0xcfc 0x4
outl 0xcf8 0x80000889
outl 0xcfc 0x1c000000
outl 0xcf8 0x80000893
outw 0xcfc 0x100
EOF
Got:
==68666== Invalid read of size 8
==68666== at 0x688536: virtio_net_queue_enable (virtio-net.c:575)
==68666== by 0x6E31AE: memory_region_write_accessor (memory.c:492)
==68666== by 0x6E098D: access_with_adjusted_size (memory.c:554)
==68666== by 0x6E4DB3: memory_region_dispatch_write (memory.c:1521)
==68666== by 0x6E31AE: memory_region_write_accessor (memory.c:492)
==68666== by 0x6E098D: access_with_adjusted_size (memory.c:554)
==68666== by 0x6E4DB3: memory_region_dispatch_write (memory.c:1521)
==68666== by 0x6EBCD3: flatview_write_continue (physmem.c:2820)
==68666== by 0x6EBFBF: flatview_write (physmem.c:2862)
==68666== by 0x6EF5E7: address_space_write (physmem.c:2958)
==68666== by 0x6DFDEC: cpu_outw (ioport.c:70)
==68666== by 0x6F6DF0: qtest_process_command (qtest.c:480)
==68666== Address 0x29087fe8 is 24 bytes after a block of size 416 in arena "client"
That is reported by Alexander Bulekov. https://gitlab.com/qemu-project/qemu/-/issues/1309
Here, the queue_index is the index of the cvq, but in some cases cvq
does not have the corresponding NetClientState, so overflow appears.
I add a check here, ignore illegal queue_index and cvq queue_index.
Note the queue_index is below the VIRTIO_QUEUE_MAX but greater or equal
than cvq index could hit this. Other devices are similar.
Fixes: 7f863302 ("virtio-net: support queue_enable")
Fixes: https://gitlab.com/qemu-project/qemu/-/issues/1309
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Message-Id: <20221110095739.130393-1-xuanzhuo@linux.alibaba.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch is part of adding vhost-user vhost_dev_start support. The
motivation is to improve backend configuration speed and reduce live
migration VM downtime.
Moving the device start routines after finishing all the necessary device
and VQ configuration, further aligning to the virtio specification for
"device initialization sequence".
Following patch will add vhost-user vhost_dev_start support.
Signed-off-by: Yajun Wu <yajunw@nvidia.com>
Acked-by: Parav Pandit <parav@nvidia.com>
Message-Id: <20221017064452.1226514-2-yajunw@nvidia.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There were several different ways to deal with the situation where the
vector specified for a msix function is out of bound:
- early return a function and keep progresssing
- propagate the error to the caller
- mark msix unusable
- assert it is in bound
- just ignore
An out-of-bound vector should not be specified if the device
implementation is correct so let msix functions always assert that the
specified vector is in range.
An exceptional case is virtio-pci, which allows the guest to configure
vectors. For virtio-pci, it is more appropriate to introduce its own
checks because it is sometimes too late to check the vector range in
msix functions.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20220829083524.143640-1-akihiko.odaki@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Yuval Shaia <yuval.shaia.ml@gmail.com>
Signed-off-by: Akihiko Odaki <<a href="mailto:akihiko.odaki@daynix.com" target="_blank">akihiko.odaki@daynix.com</a>><br>
Add virtqueue reset feature for virtio-net
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Message-Id: <20221017092558.111082-16-xuanzhuo@linux.alibaba.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add virtqueue reset feature for vhost-kernel.
Signed-off-by: Kangjie Xu <kangjie.xu@linux.alibaba.com>
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221017092558.111082-15-xuanzhuo@linux.alibaba.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Support queue_enable in vhost-kernel scenario. It can be called when
a vq reset operation has been performed and the vq is restared.
It should be noted that we can restart the vq when the vhost has
already started. When launching a new vhost device, the vhost is not
started and all vqs are not initalized until VIRTIO_PCI_COMMON_STATUS
is written. Thus, we should use vhost_started to differentiate the
two cases: vq reset and device start.
Currently it only supports vhost-kernel.
Signed-off-by: Kangjie Xu <kangjie.xu@linux.alibaba.com>
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221017092558.111082-14-xuanzhuo@linux.alibaba.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
virtio-net and vhost-kernel implement queue reset.
Queued packets in the corresponding queue pair are flushed
or purged.
For virtio-net, userspace datapath will be disabled later in
__virtio_queue_reset(). It will set addr of vring to 0 and idx to 0.
Thus, virtio_net_receive() and virtio_net_flush_tx() will not receive
or send packets.
For vhost-net, the datapath will be disabled in vhost_net_virtqueue_reset().
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Kangjie Xu <kangjie.xu@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221017092558.111082-13-xuanzhuo@linux.alibaba.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce the fucntion flush_or_purge_queued_packets(), it will be
used in device reset and virtqueue reset. Therefore, we extract the
common logic as a new function.
Signed-off-by: Kangjie Xu <kangjie.xu@linux.alibaba.com>
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221017092558.111082-12-xuanzhuo@linux.alibaba.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce vhost_net_virtqueue_restart(), which can restart the
specific virtqueue when the vhost net started running before.
If it fails to restart the virtqueue, the device will be stopped.
Here we do not reuse vhost_net_start_one() or vhost_dev_start()
because they work at queue pair level. The mem table and features
do not change, so we can call the vhost_virtqueue_start() to
restart a specific queue.
This patch only considers the case of vhost-kernel, when
NetClientDriver is NET_CLIENT_DRIVER_TAP.
Signed-off-by: Kangjie Xu <kangjie.xu@linux.alibaba.com>
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221017092558.111082-11-xuanzhuo@linux.alibaba.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce vhost_virtqueue_reset(), which can reset the specific
virtqueue in the device. Then it will unmap vrings and the desc
of the virtqueue.
Here we do not reuse the vhost_net_stop_one() or vhost_dev_stop(),
because they work at queue pair level. We do not use
vhost_virtqueue_stop() because it may stop the device in the
backend.
This patch only considers the case of vhost-kernel, when
NetClientDriver is NET_CLIENT_DRIVER_TAP.
Furthermore, we do not need net->nc->info->poll() because
it enables userspace datapath and we want to stop all
datapaths for this reset virtqueue here.
Signed-off-by: Kangjie Xu <kangjie.xu@linux.alibaba.com>
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221017092558.111082-10-xuanzhuo@linux.alibaba.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* Some more small s390x fixes and maintainer updates
* Make sure to remove all temporary files from qtests
* OpenBSD VM test update to version 7.2
* Add sndio to FreeBSD tests
* More patches to enable the qtests on Windows
-----BEGIN PGP SIGNATURE-----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=h0Ep
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2022-10-28' of https://gitlab.com/thuth/qemu into staging
* Fix and test the VISTR instruction on s390x
* Some more small s390x fixes and maintainer updates
* Make sure to remove all temporary files from qtests
* OpenBSD VM test update to version 7.2
* Add sndio to FreeBSD tests
* More patches to enable the qtests on Windows
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmNb1x8RHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbXmcA//TCliiFkhprVxzIqy7zb9uz2Odu+sS4dT
# azUSlXvC14fECm/Rb/rd2VLqCu5x2er8CYauxKQ4VhRImzcDta4kvpt/HKIppN2t
# sqw5tipJL0DYcWBwYL1llvfutM26M+Oh0igwR8uV7b+W1FjojEZdcOr9IZ6E6V55
# wQCE5OHm0VCr61QeI5IBfZTsiPo+DFomUCpj7w66j6i0CVDvmpoe36tCmvGgrcpZ
# SP7ep7/Iq+dnGh2YnJyoUOPlXeeiBCxAygOVnIRXptDeniGoliCFn7ksLdKDQ9qY
# 69pSPR/W7mTZB/HkCRalAbYuYrI9Rcqxdu6c9vcyB8Pr0snQLTf8qThY+BJ2oC4w
# JSGgWVniAk5MmrDazwNRkSbgngYLYf+CcT1h5AANuU5Kt50Bdy9Y3TuL5YVmofEp
# N4bypV0ICImQyDECz76+i5/iJOcWiRyjMfLT6y00dspeuy983xHakrsHGD8xj0U/
# 3IVxnF9bDnUSVg6lFhYrgCB3dRG1TNPJoYQOM7raS5MAPRrDtIuSabwtyn84jo4+
# 9kZRPJBriMBHNsCjGVlJ9CATmaK1SKVAbRcabjgOKoIwhZTpAe6JalykREUJlTys
# hB2V//lWWYPaSpzwY+OkvxoOmJIziixEskOmx6hPcoxID5v/bqlR69W15aUlKuLq
# VWFb+/yMvaE=
# =h0Ep
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 28 Oct 2022 09:20:31 EDT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2022-10-28' of https://gitlab.com/thuth/qemu: (21 commits)
tests/qtest: libqtest: Correct the timeout unit of blocking receive calls for win32
tests/qtest: libqos: Do not build virtio-9p unconditionally
tests/qtest: migration-test: Make sure QEMU process "to" exited after migration is canceled
tests/qtest: libqtest: Introduce qtest_wait_qemu()
tests/qtest: Use EXIT_FAILURE instead of magic number
tests/qtest: device-plug-test: Reverse the usage of double/single quotes
tests/qtest: Support libqtest to build and run on Windows
tests/qtest: Use send/recv for socket communication
accel/qtest: Support qtest accelerator for Windows
tests: Add sndio to the FreeBSD CI containers / VM
tests/vm: update openbsd to release 7.2
tests/qtest/libqos/e1000e: Use e1000_regs.h
tests/qtest/cxl-test: Remove temporary directories after testing
tests/qtest/tpm: Clean up remainders of swtpm
MAINTAINERS: target/s390x/: add Ilya as reviewer
tests/tcg/s390x: Add a test for the vistr instruction
target/s390x: Fix emulation of the VISTR instruction
tests/tcg/s390x: Test compiler flags only once, not every time
s390x/tod-kvm: don't save/restore the TOD in PV guests
s390x: step down as general arch maintainer
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The register definitions in tests/qtest/libqos/e1000e.c had names
different from hw/net/e1000_regs.h, which made it hard to understand
what test codes corresponds to the implementation. Use
hw/net/e1000_regs.h from tests/qtest/libqos/e1000e.c to remove
these duplications.
E1000E_CTRL_EXT_TXLSFLOW is removed from E1000E_CTRL_EXT settings
because hw/net/e1000_regs.h does not have the definition and it is for
TCP segmentation offload, which does not matter for the implemented
tests.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20221013055245.28102-1-akihiko.odaki@daynix.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Embed the setting of info_str in a function.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
When virtio_net_flush_tx() reaches the tx_burst value all
the queue is not flushed and nothing restart the timer.
Fix that by doing for TX timer as we do for bottom half TX:
rearming the timer if we find any packet to send during the
virtio_net_flush_tx() call.
Fixes: e3f30488e5 ("virtio-net: Limit number of packets sent per TX flush")
Cc: alex.williamson@redhat.com
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
When virtio-net is used with the socket netdev backend, the backend
can be busy and not able to collect new packets.
In this case, net_socket_receive() returns 0 and registers a poll function
to detect when the socket is ready again.
In virtio_net_tx_bh(), virtio_net_flush_tx() forwards the 0, the virtio
notifications are disabled and the function is not re-scheduled, waiting
for the backend to be ready.
When the socket netdev backend is again able to send packets, the poll
function re-starts to flush remaining packets. This is done by
calling virtio_net_tx_complete(). It re-enables notifications and calls
again virtio_net_flush_tx().
But it seems if virtio_net_flush_tx() reaches the tx_burst value all
the queue is not flushed and no new notification is sent to re-schedule
virtio_net_tx_bh(). Nothing re-start to flush the queue and remaining
packets are stuck in the queue.
To fix that, detect in virtio_net_tx_complete() if virtio_net_flush_tx()
has been stopped by tx_burst and if yes re-schedule the bottom half
function virtio_net_tx_bh() to flush the remaining packets.
This is what is done in virtio_net_tx_bh() when the virtio_net_flush_tx()
is synchronous, and completly by-passed when the operation needs to be
asynchronous.
Fixes: a697a334b3 ("virtio-net: Introduce a new bottom half packet TX")
Cc: alex.williamson@redhat.com
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This is the first step towards moving all device config size calculation
logic into the virtio core code. In particular, this adds a struct that
contains all the necessary information for common virtio code to be able
to calculate the final config size for a device. This is expected to be
used with the new virtio_get_config_size helper, which calculates the
final length based on the provided host features.
This builds on top of already existing code like VirtIOFeature and
virtio_feature_get_config_size(), but adds additional fields, as well as
sanity checking so that device-specifc code doesn't have to duplicate it.
An example usage would be:
static const VirtIOFeature dev_features[] = {
{.flags = 1ULL << FEATURE_1_BIT,
.end = endof(struct virtio_dev_config, feature_1)},
{.flags = 1ULL << FEATURE_2_BIT,
.end = endof(struct virtio_dev_config, feature_2)},
{}
};
static const VirtIOConfigSizeParams dev_cfg_size_params = {
.min_size = DEV_BASE_CONFIG_SIZE,
.max_size = sizeof(struct virtio_dev_config),
.feature_sizes = dev_features
};
// code inside my_dev_device_realize()
size_t config_size = virtio_get_config_size(&dev_cfg_size_params,
host_features);
virtio_init(vdev, VIRTIO_ID_MYDEV, config_size);
Currently every device is expected to write its own boilerplate from the
example above in device_realize(), however, the next step of this
transition is moving VirtIOConfigSizeParams into VirtioDeviceClass,
so that it can be done automatically by the virtio initialization code.
All of the users of virtio_feature_get_config_size have been converted
to use virtio_get_config_size so it's no longer needed and is removed
with this commit.
Signed-off-by: Daniil Tatianin <d-tatianin@yandex-team.ru>
Message-Id: <20220906073111.353245-2-d-tatianin@yandex-team.ru>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It was returned as error before. Instead of it, simply update the
corresponding field so qemu can send it in the migration data.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Si-Wei Liu <si-wei.liu@oracle.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Like commit 034d00d485 ("e1000: set RX descriptor status in
a separate operation"), there is also same issue in e1000e, which
would cause lost packets or stop sending packets to VM with DPDK.
Do similar fix in e1000e.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/402
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The compiler isn't clever enough to figure 'min_buf_size'
is a constant, so help it by using a definitions instead.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20220819153931.3147384-6-peter.maydell@linaro.org
The LAN9118 allows the guest to specify a level for both the TX and
RX FIFOs at which an interrupt will be generated. We implement the
RSFL_INT interrupt for the RX FIFO but are missing the handling of
the equivalent TSFL_INT for the TX FIFO. Add the missing test to set
the interrupt if the TX FIFO has exceeded the guest-specified level.
This flag is required for Micrium lan911x ethernet driver to work.
Signed-off-by: Lucas Dietrich <ld.adecy@gmail.com>
[PMM: Tweaked commit message and comment]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For consistency, function "update_rx_fifo()" should use the RX FIFO
register field names, not the TX FIFO ones, even if they refer to the
same bit positions in the register.
Signed-off-by: Anton Kochkov <anton.kochkov@proton.me>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 20220817141754.2105981-1-anton.kochkov@proton.me
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1123
[PMM: tweaked commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The DMA engine is started by I/O access and then itself accesses the
I/O registers, triggering a reentrancy bug.
The following log can reveal it:
==5637==ERROR: AddressSanitizer: stack-overflow
#0 0x5595435f6078 in tulip_xmit_list_update qemu/hw/net/tulip.c:673
#1 0x5595435f204a in tulip_write qemu/hw/net/tulip.c:805:13
#2 0x559544637f86 in memory_region_write_accessor qemu/softmmu/memory.c:492:5
#3 0x5595446379fa in access_with_adjusted_size qemu/softmmu/memory.c:554:18
#4 0x5595446372fa in memory_region_dispatch_write qemu/softmmu/memory.c
#5 0x55954468b74c in flatview_write_continue qemu/softmmu/physmem.c:2825:23
#6 0x559544683662 in flatview_write qemu/softmmu/physmem.c:2867:12
#7 0x5595446833f3 in address_space_write qemu/softmmu/physmem.c:2963:18
#8 0x5595435fb082 in dma_memory_rw_relaxed qemu/include/sysemu/dma.h:87:12
#9 0x5595435fb082 in dma_memory_rw qemu/include/sysemu/dma.h:130:12
#10 0x5595435fb082 in dma_memory_write qemu/include/sysemu/dma.h:171:12
#11 0x5595435fb082 in stl_le_dma qemu/include/sysemu/dma.h:272:1
#12 0x5595435fb082 in stl_le_pci_dma qemu/include/hw/pci/pci.h:910:1
#13 0x5595435fb082 in tulip_desc_write qemu/hw/net/tulip.c:101:9
#14 0x5595435f7e3d in tulip_xmit_list_update qemu/hw/net/tulip.c:706:9
#15 0x5595435f204a in tulip_write qemu/hw/net/tulip.c:805:13
Fix this bug by restricting the DMA engine to memories regions.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
