When icount and ibreak exceptions are due to happen on the same address
icount has higher precedence.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20231130171920.3798954-3-jcmvbkbc@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
make check-tcg fails on Fedora with:
vtimer.c:9:10: fatal error: inttypes.h: No such file or directory
Fedora has a minimal aarch64 cross-compiler, which satisfies the
configure checks, so it's chosen instead of the dockerized one.
There is no cross-version of inttypes.h, however.
Fix by using stdint.h instead. The test does not require anything
from inttypes.h anyway.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-ID: <20240108125030.58569-1-iii@linux.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a small test to prevent regressions. Userspace runs in primary
mode, so LAE should always set the access register to 0.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-ID: <20240111092328.929421-3-iii@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
ALU instructions can write to both memory and flags. If the CC_SRC*
and CC_DST locations have been written already when a memory access
causes a fault, the value in CC_SRC* and CC_DST might be interpreted
with the wrong CC_OP (the one that is in effect before the instruction.
Besides just using the wrong result for the flags, something like
subtracting -1 can have disastrous effects if the current CC_OP is
CC_OP_EFLAGS: this is because QEMU does not expect bits outside the ALU
flags to be set in CC_SRC, and env->eflags can end up set to all-ones.
In the case of the attached testcase, this sets IOPL to 3 and would
cause an assertion failure if SUB is moved to the new decoder.
This mechanism is not really needed for BMI instructions, which can
only write to a register, but put it to use anyway for cleanliness.
In the case of BZHI, the code has to be modified slightly to ensure
that decode->cc_src is written, otherwise the new assertions trigger.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In commit edac4d8a16 back in 2015 when we added support for
the virtual timer offset CNTVOFF_EL2, we didn't correctly update
the timer-recalculation code that figures out when the timer
interrupt is next going to change state. We got it wrong in
two ways:
* for the 0->1 transition, we didn't notice that gt->cval + offset
can overflow a uint64_t
* for the 1->0 transition, we didn't notice that the transition
might now happen before the count rolls over, if offset > count
In the former case, we end up trying to set the next interrupt
for a time in the past, which results in QEMU hanging as the
timer fires continuously.
In the latter case, we would fail to update the interrupt
status when we are supposed to.
Fix the calculations in both cases.
The test case is Alex Bennée's from the bug report, and tests
the 0->1 transition overflow case.
Fixes: edac4d8a16 ("target-arm: Add CNTVOFF_EL2")
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/60
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20231120173506.3729884-1-peter.maydell@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
The reason the ppc64 and s390x test where failing was because gdb
hides them although they are still accessible via regnum. We can
re-arrange the test a little bit and include these two arches in our
test.
We also need to be a bit more careful handling remote-registers as the
format isn't easily parsed with pure white space separation. Once we
fold types like "long long" and "long double" into a single word we
can now assert all registers are either listed or elided.
Cc: Ilya Leoshkevich <iii@linux.ibm.com>
Cc: <qemu-s390x@nongnu.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Daniel Henrique Barboza <danielhb413@gmail.com>
Cc: <qemu-ppc@nongnu.org>
Cc: Luis Machado <luis.machado@arm.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20231121153606.542101-1-alex.bennee@linaro.org>
This still remains a MANUAL test due to blocking issues.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20231120150833.2552739-13-alex.bennee@linaro.org>
To make it easier to test 32 bit Arm softmmu issues implement a basic
boot.S so we can build the multiarch tests. Currently CHECK_UNALIGNED
is disabled as I haven't got the right magic set for it to work.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20231120150833.2552739-12-alex.bennee@linaro.org>
Prepare for expanding the arm system tests by cleaning up the test
directory.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20231120150833.2552739-11-alex.bennee@linaro.org>
We need to ensure we squash the serial port if we want to hand craft
our muxed input. As a bonus emit the example with a V=1 build to make
it easier for people to figure out.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20231120150833.2552739-7-alex.bennee@linaro.org>
The patch below fixes a bug in the VSX_CVT_FP_TO_INT and VSX_CVT_FP_TO_INT2
macros in target/ppc/fpu_helper.c where a non-NaN floating point value from the
source vector is incorrectly converted to 0, 0x80000000, or 0x8000000000000000
instead of the expected value if a preceding source floating point value from
the same source vector was a NaN.
The bug in the VSX_CVT_FP_TO_INT and VSX_CVT_FP_TO_INT2 macros in
target/ppc/fpu_helper.c was introduced with commit c3f24257e3.
This patch also adds a new vsx_f2i_nan test in tests/tcg/ppc64 that checks that
the VSX xvcvspsxws, xvcvspuxws, xvcvspsxds, xvcvspuxds, xvcvdpsxws, xvcvdpuxws,
xvcvdpsxds, and xvcvdpuxds instructions correctly convert non-NaN floating point
values to integer values if the source vector contains NaN floating point values.
Fixes: c3f24257e3 ("target/ppc: Clear fpstatus flags on helpers missing it")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1941
Signed-off-by: John Platts <john_platts@hotmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
nios2 signal tests are broken again:
retry.py -n 10 -c -- ./qemu-nios2 ./tests/tcg/nios2-linux-user/signals
Results summary:
0: 8 times (80.00%), avg time 2.254 (0.00 varience/0.00 deviation)
-11: 2 times (20.00%), avg time 0.253 (0.00 varience/0.00 deviation)
Ran command 10 times, 8 passes
This wasn't picked up by CI as we don't have a docker container that
can build QEMU with the nios2 compiler. I don't have time to bisect
the breakage and the target is orphaned anyway so take the easy route
and revert it.
This reverts commit 20e7524ff9.
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20231106185112.2755262-23-alex.bennee@linaro.org>
We already do a couple of "info registers" for specific tests but this
is a more comprehensive multiarch test. It also has some output
helpful for debugging the gdbstub by showing which XML features are
advertised and what the underlying register numbers are.
My initial motivation was to see if there are any duplicate register
names exposed via the gdbstub while I was reviewing the proposed
register interface for TCG plugins.
Mismatches between the xml and remote-desc are reported for debugging
but do not fail the test.
We also skip the tests for the following arches for now until we can
investigate and fix any issues:
- s390x (fails to read v0l->v15l, not seen in remote-registers)
- ppc64 (fails to read vs0h->vs31h, not seen in remote-registers)
Cc: Akihiko Odaki <akihiko.odaki@daynix.com>
Cc: Luis Machado <luis.machado@linaro.org>
Cc: Ilya Leoshkevich <iii@linux.ibm.com>
Cc: qemu-s390x@nongnu.org
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Daniel Henrique Barboza <danielhb413@gmail.com>
Cc: qemu-ppc@nongnu.org
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20231106185112.2755262-7-alex.bennee@linaro.org>
Add a test that tries different combinations of ADD LOGICAL WITH
CARRY instructions.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-ID: <20231106093605.1349201-6-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add a small test to prevent regressions.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20231106093605.1349201-5-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add a small test to prevent regressions.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20231106093605.1349201-3-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The previous change missed updating one of the increments and
one of the MemOps. Add a test case for all vector lengths.
Cc: qemu-stable@nongnu.org
Fixes: e6dd5e782b ("target/arm: Use tcg_gen_qemu_{ld, st}_i128 in gen_sve_{ld, st}r")
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20231031143215.29764-1-richard.henderson@linaro.org
[PMM: fixed checkpatch nit]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A build of GCC 13.2 will have stack protector enabled by default if it
was configured with --enable-default-ssp option. For such a compiler,
it is necessary to explicitly disable stack protector when linking
without standard libraries.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20230731091042.139159-3-akihiko.odaki@daynix.com>
[AJB: fix comment string typo]
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20231029145033.592566-3-alex.bennee@linaro.org>
Some instructions use YMM0 implicitly, or use YMM9 as a read-modify-write
register destination. Initialize those registers as well.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This can cause differences between native and QEMU execution, due
to ASLR.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Unify HAVE_GDB_BIN (currently in config-host.mak) and
HOST_GDB_SUPPORTS_ARCH into a single GDB variable in
config-target.mak.
Reviewed-by: Emmanouil Pitsidianakis <manos.pitsidianakis@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
test-aes, sha1-vector and sha512-vector need not be conditional on
$(CROSS_CC_HAS_SVE), reorganize the "if"s to move them outside.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The system test shutdown uses the 'loongarch_virt_pm' region.
We can use the write AcpiFadtData.sleep_clt register to realize the shutdown.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Message-ID: <20231012072351.1409344-1-gaosong@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20231004090629.37473-6-philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
some insns use the result register implicitly as an input. Thus, we
could end up with data from the previous insn spilling over.
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-ID: <20230913105326.40832-4-kbastian@mail.uni-paderborn.de>
RSx for d regs and e regs now use the same numbering. This makes sure
that mixing d and e registers in an insn test will not overwrite data
between registers.
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-ID: <20230913105326.40832-2-kbastian@mail.uni-paderborn.de>
we would crash if width was 0 for these insns, as tcg_gen_deposit() is
undefined for that case. For TriCore, width = 0 is a mov from the src reg
to the dst reg, so we special case this here.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-ID: <20230828112651.522058-9-kbastian@mail.uni-paderborn.de>
we don't want to exclude ISA v1.6.2 insns from our tests.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-Id: <20230828112651.522058-2-kbastian@mail.uni-paderborn.de>
For user-only mode we reveal a subset of the AArch64 ID registers
to the guest, to emulate the kernel's trap-and-emulate-ID-regs
handling. Update the feature bit masks to match upstream kernel
commit a48fa7efaf1161c1c.
None of these features are yet implemented by QEMU, so this
doesn't yet have a behavioural change, but implementation of
FEAT_MOPS and FEAT_HBC is imminent.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Motorola treats denormals with explicit integer bit set as
having unbiased exponent 0, unlike Intel which treats it as
having unbiased exponent 1 (more like all other IEEE formats
that have no explicit integer bit).
Add a flag on FloatFmt to differentiate the behaviour.
Reported-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
With FEAT_FPAC, AUT* instructions that fail authentication
do not produce an error value but instead fault.
For pauth-2, install a signal handler and verify it gets called.
For pauth-4 and pauth-5, we are explicitly testing the error value,
so there's nothing to test with FEAT_FPAC, so exit early.
Adjust the makefile to use -cpu neoverse-v1, which has FEAT_EPAC
but not FEAT_FPAC.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230829232335.965414-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* target/i386: fix BQL handling of the legacy FERR interrupts
* target/i386: fix memory operand size for CVTPS2PD
* target/i386: Add support for AMX-COMPLEX in CPUID enumeration
* compile plugins on Darwin
* configure and meson cleanups
* drop mkvenv support for Python 3.7 and Debian10
* add wrap file for libblkio
* tweak KVM stubs
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmT5t6UUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMmjwf+MpvVuq+nn+3PqGUXgnzJx5ccA5ne
O9Xy8+1GdlQPzBw/tPovxXDSKn3HQtBfxObn2CCE1tu/4uHWpBA1Vksn++NHdUf2
P0yoHxGskJu5iYYTtIcNw5cH2i+AizdiXuEjhfNjqD5Y234cFoHnUApt9e3zBvVO
cwGD7WpPuSb4g38hHkV6nKcx72o7b4ejDToqUVZJ2N+RkddSqB03fSdrOru0hR7x
V+lay0DYdFszNDFm05LJzfDbcrHuSryGA91wtty7Fzj6QhR/HBHQCUZJxMB5PI7F
Zy4Zdpu60zxtSxUqeKgIi7UhNFgMcax2Hf9QEqdc/B4ARoBbboh4q4u8kQ==
=dH7/
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://gitlab.com/bonzini/qemu into staging
* only build util/async-teardown.c when system build is requested
* target/i386: fix BQL handling of the legacy FERR interrupts
* target/i386: fix memory operand size for CVTPS2PD
* target/i386: Add support for AMX-COMPLEX in CPUID enumeration
* compile plugins on Darwin
* configure and meson cleanups
* drop mkvenv support for Python 3.7 and Debian10
* add wrap file for libblkio
* tweak KVM stubs
# -----BEGIN PGP SIGNATURE-----
#
# iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmT5t6UUHHBib256aW5p
# QHJlZGhhdC5jb20ACgkQv/vSX3jHroMmjwf+MpvVuq+nn+3PqGUXgnzJx5ccA5ne
# O9Xy8+1GdlQPzBw/tPovxXDSKn3HQtBfxObn2CCE1tu/4uHWpBA1Vksn++NHdUf2
# P0yoHxGskJu5iYYTtIcNw5cH2i+AizdiXuEjhfNjqD5Y234cFoHnUApt9e3zBvVO
# cwGD7WpPuSb4g38hHkV6nKcx72o7b4ejDToqUVZJ2N+RkddSqB03fSdrOru0hR7x
# V+lay0DYdFszNDFm05LJzfDbcrHuSryGA91wtty7Fzj6QhR/HBHQCUZJxMB5PI7F
# Zy4Zdpu60zxtSxUqeKgIi7UhNFgMcax2Hf9QEqdc/B4ARoBbboh4q4u8kQ==
# =dH7/
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 07 Sep 2023 07:44:37 EDT
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* tag 'for-upstream' of https://gitlab.com/bonzini/qemu: (51 commits)
docs/system/replay: do not show removed command line option
subprojects: add wrap file for libblkio
sysemu/kvm: Restrict kvm_pc_setup_irq_routing() to x86 targets
sysemu/kvm: Restrict kvm_has_pit_state2() to x86 targets
sysemu/kvm: Restrict kvm_get_apic_state() to x86 targets
sysemu/kvm: Restrict kvm_arch_get_supported_cpuid/msr() to x86 targets
target/i386: Restrict declarations specific to CONFIG_KVM
target/i386: Allow elision of kvm_hv_vpindex_settable()
target/i386: Allow elision of kvm_enable_x2apic()
target/i386: Remove unused KVM stubs
target/i386/cpu-sysemu: Inline kvm_apic_in_kernel()
target/i386/helper: Restrict KVM declarations to system emulation
hw/i386/fw_cfg: Include missing 'cpu.h' header
hw/i386/pc: Include missing 'cpu.h' header
hw/i386/pc: Include missing 'sysemu/tcg.h' header
Revert "mkvenv: work around broken pip installations on Debian 10"
mkvenv: assume presence of importlib.metadata
Python: Drop support for Python 3.7
configure: remove dead code
meson: list leftover CONFIG_* symbols
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
$(HOST_CC) is only used to invoke the preprocessor, and $(CC) can be
used instead now that there is a Tricore C compiler. Remove the variable
from config-host.mak.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* Check for availablility of more devices in qtests before using them
* Some other minor qtest fixes
-----BEGIN PGP SIGNATURE-----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=tZWg
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2023-08-31' of https://gitlab.com/thuth/qemu into staging
* Use precise selfmodifying code mode on s390x TCG
* Check for availablility of more devices in qtests before using them
* Some other minor qtest fixes
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmTw5v4RHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbX2DRAAo7NPNPQ2nsYDdYfKAGt8OSg1BHqh1RYH
# jvLiU5xrWQ3whmSJYw4rcSyBk4yC+lIjoXT6oBn6O40Q1r7OmrWgtrn9g//3SLHb
# Wfob5bZkmRiETDZNFFpYcpRPzElF3ZqIfwOhJ3zfmAQxqeTxpTnAuq2vI38pk3Hz
# 4pQR/j2IKZFmFt6cdYUaKi32odDK6ySKAFCKy9I8sz2hJgOXQRYBkjorDx+g+hoF
# o7DTGkA3uH2xXlLQKhbEGm5xQMlcBgTMb2XeguvRbb7g/Uc046homwm0r6rejDy5
# EgW9Kx3Y34QYZt51onqmA57MNNQboubHkSz9W2b57OX+IWA3VRncdBAxdGmubRTY
# Jb6LsBZSMdKQBXxgIP3DZjvH6MxYjA9Iy3YI7Mk+hJnDACkFVJOCPxS9acnmjYE5
# Nn935GmbYMazfci0c3zc/899hAGDNglD9Tf6ourBjl1WLQstefXhlpzkbGWqSFjF
# Tovpal+Rm6KLDFSfs6TsRp6+FF8a6C1k251Ai67adkiCYM/jKwVoiHrsUJeG0vyc
# 791x5+lixxkLUHu1qNYfEdxvaOE8guhXRt3zJIjmphio3v+RFBLbzC6lTzeZbTTv
# DpnnoFJ/tCzdLew7A1QuzuW361ywyKVE4Qp8HQfaJCOJT9aGgMdyoHlpgz0ojgJm
# fD8Vfl9GZFQ=
# =tZWg
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 31 Aug 2023 15:16:14 EDT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2023-08-31' of https://gitlab.com/thuth/qemu:
meson: test for CONFIG_TCG in config_all
subprojects/berkeley-testfloat-3: Update to fix a problem with compiler warnings
tests/qtest/bios-tables-test: Check for virtio-iommu device before using it
tests/qtest/netdev-socket: Avoid variable-length array in inet_get_free_port_multiple()
tests/qtest/usb-hcd-xhci-test: Check availability of devices before using them
tests/tcg/s390x: Test precise self-modifying code handling
target/s390x: Define TARGET_HAS_PRECISE_SMC
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Since commit 139c1837db ("meson: rename included C source files
to .c.inc"), QEMU standard procedure for included C files is to
use *.c.inc.
Besides, since commit 6a0057aa22 ("docs/devel: make a statement
about includes") this is documented as the Coding Style:
If you do use template header files they should be named with
the ``.c.inc`` or ``.h.inc`` suffix to make it clear they are
being included for expansion.
Therefore rename 'bti-crt.inc.c' as 'bti-crt.c.inc'.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230606141252.95032-6-philmd@linaro.org>
Add small softmmu and user tests to prevent regressions.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230807114921.438881-2-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This fix is implemented by having the vCont handler set the value of
`gdbserver_state.c_cpu` if any threads are to be resumed. The specific
CPU picked is arbitrarily from the ones to be resumed, but it should
be okay, as all GDB cares about is that it is a resumed thread.
Signed-off-by: Matheus Branco Borella <dark.ryu.550@gmail.com>
Message-Id: <20230804182633.47300-2-dark.ryu.550@gmail.com>
[AJB: style and whitespace fixes]
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1725
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230829161528.2707696-9-alex.bennee@linaro.org>
We can do this all in the run-test.py script so remove the extraneous
bits from the individual tests which got copied from the original
non-CI gdb tests.
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230829161528.2707696-8-alex.bennee@linaro.org>
This avoids ugly multi-line wrapping for the test on non V=1 builds.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230829161528.2707696-4-alex.bennee@linaro.org>
Add a small test to prevent regressions.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230804233748.218935-4-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add a small test to prevent regressions.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230807163459.849766-2-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add a small test to prevent regressions.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230804235624.263260-2-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
When load_atom_extract_al16_or_al8 is inexpensive, we want to use
it early, in order to avoid the overhead of required_atomicity.
However, we must not read past the end of the page.
If there are more than 8 bytes remaining, then both the "aligned 16"
and "aligned 8" paths align down so that the read has at least
16 bytes remaining on the page.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This test fails when host page size != guest page size,
because qemu may not be able to directly map the file.
Fixes: a634148269 ("tests/tcg: Add a test for info proc mappings")
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add a small test to prevent regressions.
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230724082032.66864-15-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add a small test to prevent regressions.
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230724082032.66864-14-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add a small test to prevent regressions.
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230724082032.66864-13-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add a small test to prevent regressions.
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230724082032.66864-12-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add a small test to prevent regressions.
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230724082032.66864-11-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add a small test to prevent regressions.
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230724082032.66864-10-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add a small test to prevent regressions.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230724082032.66864-9-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
* Use xl instead of mxl for disassemble
* Factor out extension tests to cpu_cfg.h
* disas/riscv: Add vendor extension support
* disas/riscv: Add support for XVentanaCondOps
* disas/riscv: Add support for XThead* instructions
* Fix mstatus related problems
* Fix veyron-v1 CPU properties
* Fix the xlen for data address when MPRV=1
* opensbi: Upgrade from v1.2 to v1.3
* Enable 32-bit Spike OpenSBI boot testing
* Support the watchdog timer of HiFive 1 rev b
* Only build qemu-system-riscv$$ on rv$$ host
* Add RVV registers to log
* Restrict ACLINT to TCG
* Add syscall riscv_hwprobe
* Add support for BF16 extensions
* KVM_RISCV_SET_TIMER macro is not configured correctly
* Generate devicetree only after machine initialization is complete
* virt: Convert fdt_load_addr to uint64_t
* KVM: fixes and enhancements
* Add support for the Zfa extension
-----BEGIN PGP SIGNATURE-----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=3XFD
-----END PGP SIGNATURE-----
Merge tag 'pull-riscv-to-apply-20230710-1' of https://github.com/alistair23/qemu into staging
Third RISC-V PR for 8.1
* Use xl instead of mxl for disassemble
* Factor out extension tests to cpu_cfg.h
* disas/riscv: Add vendor extension support
* disas/riscv: Add support for XVentanaCondOps
* disas/riscv: Add support for XThead* instructions
* Fix mstatus related problems
* Fix veyron-v1 CPU properties
* Fix the xlen for data address when MPRV=1
* opensbi: Upgrade from v1.2 to v1.3
* Enable 32-bit Spike OpenSBI boot testing
* Support the watchdog timer of HiFive 1 rev b
* Only build qemu-system-riscv$$ on rv$$ host
* Add RVV registers to log
* Restrict ACLINT to TCG
* Add syscall riscv_hwprobe
* Add support for BF16 extensions
* KVM_RISCV_SET_TIMER macro is not configured correctly
* Generate devicetree only after machine initialization is complete
* virt: Convert fdt_load_addr to uint64_t
* KVM: fixes and enhancements
* Add support for the Zfa extension
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEaukCtqfKh31tZZKWr3yVEwxTgBMFAmSr+ekACgkQr3yVEwxT
# gBMMGg//ZCcyH3KXB49c2KUIFO6FKYUxN9uC3giZCtuGyEH8T2yDgZVVXnxwU+Ij
# +3Ej6T/ZdWMpePC9qf+xKzHWZk7Qc8Tcg+JgQbga573894yZInRwYl8HsSlEKA+Z
# vlqSBPxTlp9rlDwGP/LjGljyIFqL4konk9zi3FL4ZXTF1iHUGrh/953Y3wIreEfl
# KX5UznnWcgy2BqQT1vihMbM8qCVK6iryH+QZ6LiAsPMSX1rIzk8ectQryILzoIYh
# bMiwCLVMyr4ZrUXjmGTF+7/WcOWwhhyfpdstf2iotKALelZtVHit0wHcty2GYQde
# nvN83jJWu04DGXkPBUsqCUQXczGo1QHjJUH3RIRJzfOby/lGt4pSzHAfKA+iNUht
# ikM3SdBsXMO+ogjTtTcCMb7/m2vsMoQP60VRts9Mh3YVD0cgr7RqpqRoEMugVYnr
# ca8Vijf71mB+y+pq477eV1Q8BoKpr8xa1OlFkNKPC17uMD7HoDMI44QgFOgtYp10
# TMsqqyB75q6PZhSEwm63xbmH0Zpo8kSqT/E3MTtGTyPeuL8TNNNSkCmFaGYmRrbI
# XEp7vG2RaDJOvDomS3nUhA5ruc8SaXd0q25q2gLYQfCsehfFqZAwuNB5xf1zS0M0
# ov1/gwaqU93t6nLbo2cCbb0plkIFKwwJ9KKjD06wJ4KPe0TGFzk=
# =3XFD
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 10 Jul 2023 01:30:33 PM BST
# gpg: using RSA key 6AE902B6A7CA877D6D659296AF7C95130C538013
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6AE9 02B6 A7CA 877D 6D65 9296 AF7C 9513 0C53 8013
* tag 'pull-riscv-to-apply-20230710-1' of https://github.com/alistair23/qemu: (54 commits)
riscv: Add support for the Zfa extension
target/riscv/kvm.c: read/write (cbom|cboz)_blocksize in KVM
target/riscv/kvm.c: add kvmconfig_get_cfg_addr() helper
target/riscv: update multi-letter extension KVM properties
target/riscv/cpu.c: create KVM mock properties
target/riscv/cpu.c: remove priv_ver check from riscv_isa_string_ext()
target/riscv/cpu.c: add satp_mode properties earlier
target/riscv/kvm.c: add multi-letter extension KVM properties
target/riscv/kvm.c: update KVM MISA bits
target/riscv: add KVM specific MISA properties
target/riscv/cpu: add misa_ext_info_arr[]
target/riscv/kvm.c: init 'misa_ext_mask' with scratch CPU
target/riscv: handle mvendorid/marchid/mimpid for KVM CPUs
target/riscv: read marchid/mimpid in kvm_riscv_init_machine_ids()
target/riscv: use KVM scratch CPUs to init KVM properties
target/riscv/cpu.c: restrict 'marchid' value
target/riscv/cpu.c: restrict 'mimpid' value
target/riscv/cpu.c: restrict 'mvendorid' value
hw/riscv/virt.c: skip 'mmu-type' FDT if satp mode not set
target/riscv: skip features setup for KVM CPUs
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
clang does not support expressions involving symbols in instructions
like lghi yet, so building hello-s390x-asm.S with it fails.
Move the expression to the literal pool and load it from there.
Fixes: be4a4cb429 ("tests/tcg/s390x: Test single-stepping SVC")
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230707154242.457706-1-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add a small test to prevent regressions.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230704081506.276055-13-iii@linux.ibm.com>
[thuth: Apply fix for compiling with GCC 11]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add a small test to prevent regressions.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230704081506.276055-12-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add a small test to prevent regressions.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230704081506.276055-11-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add a small test to prevent regressions.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230704081506.276055-10-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add a small test to prevent regressions.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230704081506.276055-9-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This patch introduces the RISC-V Zfa extension, which introduces
additional floating-point instructions:
* fli (load-immediate) with pre-defined immediates
* fminm/fmaxm (like fmin/fmax but with different NaN behaviour)
* fround/froundmx (round to integer)
* fcvtmod.w.d (Modular Convert-to-Integer)
* fmv* to access high bits of float register bigger than XLEN
* Quiet comparison instructions (fleq/fltq)
Zfa defines its instructions in combination with the following extensions:
* single-precision floating-point (F)
* double-precision floating-point (D)
* quad-precision floating-point (Q)
* half-precision floating-point (Zfh)
Since QEMU does not support the RISC-V quad-precision floating-point
ISA extension (Q), this patch does not include the instructions that
depend on this extension. All other instructions are included in this
patch.
The Zfa specification can be found here:
https://github.com/riscv/riscv-isa-manual/blob/master/src/zfa.tex
The Zfa specifciation is frozen and is in public review since May 3, 2023:
https://groups.google.com/a/groups.riscv.org/g/isa-dev/c/SED4ntBkabg
The patch also includes a TCG test for the fcvtmod.w.d instruction.
The test cases test for correct results and flag behaviour.
Note, that the Zfa specification requires fcvtmod's flag behaviour
to be identical to a fcvt with the same operands (which is also
tested).
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
Message-Id: <20230710071243.282464-1-christoph.muellner@vrull.eu>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Use a shared driver and backends for i386, aarch64, ppc64, riscv64.
Acked-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
For the outer product set of insns, which take an entire matrix
tile as output, the argument is not a combined tile+column.
Therefore using get_tile_rowcol was incorrect, as we extracted
the tile number from itself.
The test case relies only on assembler support for SME, since
no release of GCC recognizes -march=armv9-a+sme yet.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1620
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230622151201.1578522-5-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: dropped now-unneeded changes to sysregs CFLAGS]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some assemblers will complain about attempts to access
id_aa64zfr0_el1 and id_aa64smfr0_el1 by name if the test
binary isn't built for the right processor type:
/tmp/ccASXpLo.s:782: Error: selected processor does not support system register name 'id_aa64zfr0_el1'
/tmp/ccASXpLo.s:829: Error: selected processor does not support system register name 'id_aa64smfr0_el1'
However, these registers are in the ID space and are guaranteed to
read-as-zero on older CPUs, so the access is both safe and sensible.
Switch to using the S syntax, as we already do for ID_AA64ISAR2_EL1
and ID_AA64MMFR2_EL1. This allows us to drop the HAS_ARMV9_SME check
and the makefile machinery to adjust the CFLAGS for this test, so we
don't rely on having a sufficiently new compiler to be able to check
these registers.
This means we're actually testing the SME ID register: no released
GCC yet recognizes -march=armv9-a+sme, so that was always skipped.
It also avoids a future problem if we try to switch the "do we have
SME support in the toolchain" check from "in the compiler" to "in the
assembler" (at which point we would otherwise run into the above
errors).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a small test to prevent regressions.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230621203627.1808446-9-iii@linux.ibm.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230630180423.558337-39-alex.bennee@linaro.org>
The lack of SVE memory instrumentation has been an omission in plugin
handling since it was introduced. Fortunately we can utilise the
probe_* functions to force all all memory access to follow the slow
path. We do this by checking the access type and presence of plugin
memory callbacks and if set return the TLB_MMIO flag.
We have to jump through a few hoops in user mode to re-use the flag
but it was the desired effect:
./qemu-system-aarch64 -display none -serial mon:stdio \
-M virt -cpu max -semihosting-config enable=on \
-kernel ./tests/tcg/aarch64-softmmu/memory-sve \
-plugin ./contrib/plugins/libexeclog.so,ifilter=st1w,afilter=0x40001808 -d plugin
gives (disas doesn't currently understand st1w):
0, 0x40001808, 0xe54342a0, ".byte 0xa0, 0x42, 0x43, 0xe5", store, 0x40213010, RAM, store, 0x40213014, RAM, store, 0x40213018, RAM
And for user-mode:
./qemu-aarch64 \
-plugin contrib/plugins/libexeclog.so,afilter=0x4007c0 \
-d plugin \
./tests/tcg/aarch64-linux-user/sha512-sve
gives:
1..10
ok 1 - do_test(&tests[i])
0, 0x4007c0, 0xa4004b80, ".byte 0x80, 0x4b, 0x00, 0xa4", load, 0x5500800370, load, 0x5500800371, load, 0x5500800372, load, 0x5500800373, load, 0x5500800374, load, 0x5500800375, load, 0x5500800376, load, 0x5500800377, load, 0x5500800378, load, 0x5500800379, load, 0x550080037a, load, 0x550080037b, load, 0x550080037c, load, 0x550080037d, load, 0x550080037e, load, 0x550080037f, load, 0x5500800380, load, 0x5500800381, load, 0x5500800382, load, 0x5500800383, load, 0x5500800384, load, 0x5500800385, load, 0x5500800386, lo
ad, 0x5500800387, load, 0x5500800388, load, 0x5500800389, load, 0x550080038a, load, 0x550080038b, load, 0x550080038c, load, 0x550080038d, load, 0x550080038e, load, 0x550080038f, load, 0x5500800390, load, 0x5500800391, load, 0x5500800392, load, 0x5500800393, load, 0x5500800394, load, 0x5500800395, load, 0x5500800396, load, 0x5500800397, load, 0x5500800398, load, 0x5500800399, load, 0x550080039a, load, 0x550080039b, load, 0x550080039c, load, 0x550080039d, load, 0x550080039e, load, 0x550080039f, load, 0x55008003a0, load, 0x55008003a1, load, 0x55008003a2, load, 0x55008003a3, load, 0x55008003a4, load, 0x55008003a5, load, 0x55008003a6, load, 0x55008003a7, load, 0x55008003a8, load, 0x55008003a9, load, 0x55008003aa, load, 0x55008003ab, load, 0x55008003ac, load, 0x55008003ad, load, 0x55008003ae, load, 0x55008003af
(4007c0 is the ld1b in the sha512-sve)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Cc: Robert Henry <robhenry@microsoft.com>
Cc: Aaron Lindsay <aaron@os.amperecomputing.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230630180423.558337-20-alex.bennee@linaro.org>
We recently missed a regression that should have been picked up by
check-tcg. This was because the libmem plugin is effectively a NOP if
the user doesn't specify the type to use.
Rather than changing the default behaviour add an additional expansion
so we can take this into account in future.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230630180423.558337-6-alex.bennee@linaro.org>
Test for invalid, integer overflow, and inexact.
Test for proper result, modulo 2**64.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230527141910.1885950-3-richard.henderson@linaro.org>
The stack array is only referenced from the start-up code (which is
shared between the s390-ccw.img and the s390-netboot.img), but it is
currently declared twice, once in main.c and once in netmain.c.
It makes more sense to declare this in start.S instead - which will
also be helpful in the next patch, since we need to mention the .bss
section in start.S in that patch.
While we're at it, let's also drop the huge alignment of the stack,
since there is no technical requirement for aligning it to page
boundaries.
Message-Id: <20230627074703.99608-4-thuth@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This is a perfectly natural occurrence for x86 "rep movb",
where the "rep" prefix forms a counted loop of the one insn.
During the tests/tcg/multiarch/memory test, this logging is
triggered over 350000 times. Within the context of cross-i386-tci
build, which is already slow by nature, the logging is sufficient
to push the test into timeout.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
this allows us to exercise the startup code used by GCC to call main().
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-Id: <20230526061946.54514-4-kbastian@mail.uni-paderborn.de>
the linker might rearrange sections, so lets reference memory by label
name instead of addr + off.
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-Id: <20230526061946.54514-3-kbastian@mail.uni-paderborn.de>
this seperates these tests from the upcoming tests written in C.
Also rename the compiled test to 'test_<foo>.asm.tst'.
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-Id: <20230526061946.54514-2-kbastian@mail.uni-paderborn.de>
Test execution of DC CVAP and DC CVADP instructions under user mode
emulation.
Signed-off-by: Zhuojia Shen <chaosdefinition@hotmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With -cpu max and FEAT_LSE2, the __aarch64__ section will only raise
an alignment exception when the load crosses a 16-byte boundary.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230530191438.411344-20-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We have many other instances of stg in the testsuite;
change these to provide an instance of stz2g.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230530191438.411344-19-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a small test to prevent regressions.
Cc: qemu-stable@nongnu.org
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230601223027.795501-3-iii@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add a small test to prevent regressions.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Acked-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230510230213.330134-3-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add a small test to prevent regressions.
Cc: qemu-stable@nongnu.org
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230526181240.1425579-5-iii@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add a test to prevent regressions.
Cc: qemu-stable@nongnu.org
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230526181240.1425579-3-iii@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The order in which instructions are generated by gen_insn() influences
assignment to tmp registers. During generation, tmp instructions (e.g.
generate_V6_vassign_tmp) use vreg_src_off() to determine what kind of
register to use as source. If some instruction (e.g.
generate_V6_vmpyowh_64_acc) uses a tmp register but is generated prior
to the corresponding tmp instruction, the vregs_updated_tmp bit map
isn't updated in time.
Exmple:
{ v14.tmp = v16; v25 = v14 } This works properly because
generate_V6_vassign_tmp is generated before generate_V6_vassign
and the bit map is updated.
{ v15:14.tmp = vcombine(v21, v16); v25:24 += vmpyo(v18.w,v14.h) }
This does not work properly because vmpyo is generated before
vcombine and therefore the bit map does not yet know that there's
a tmp register.
The parentheses in the decoding function were in the wrong place.
Moving them to the correct location makes shuffling of .tmp vector
registers work as expected.
Signed-off-by: Marco Liebel <quic_mliebel@quicinc.com>
Reviewed-by: Taylor Simpson <tsimpson@quicinc.com>
Tested-by: Taylor Simpson <tsimpson@quicinc.com>
Signed-off-by: Taylor Simpson <tsimpson@quicinc.com>
Reviewed-by: Brian Cain <bcain@quicinc.com>
Message-Id: <20230522174708.464197-1-quic_mliebel@quicinc.com>
Move test infra to header file
check functions (always print line number on error)
USR manipulation
Useful floating point values
Use stdint.h types
Use stdbool.h bool where appropriate
Use trip counts local to for loop
Suggested-by: Anton Johansson <anjo@rev.ng>
Signed-off-by: Taylor Simpson <tsimpson@quicinc.com>
Reviewed-by: Anton Johansson <anjo@rev.ng>
Tested-by: Anton Johansson <anjo@rev.ng>
Message-Id: <20230522174341.1805460-1-tsimpson@quicinc.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEENjXHiM5iuR/UxZq0ewJE+xLeRCIFAmRmgQgACgkQewJE+xLe
RCJLtAf8C/0kQRa4mjnbsztXuFyca53UxAv3BSBEDla4ZcMfFBoVJsGB3OP7IPXd
KBQpkLyJAVye9idex5xqdp9nIfoGKDTsc6YtCfGujZ17cDpzLRDpHdUTex8PcZYK
wpfM3hoVJsYRBMsojZ4OaxatjFQ+FWzrIH6FcgH086Q8TH4w9dZLNEJzHC4lOj0s
7qOuw2tgm+vOVlzsk/fv6/YD/BTeZTON3jgTPvAnvdRLb/482UpM9JkJ8E4rbte3
Ss5PUK8QTQHU0yamspGy/PfsYxiptM+jIWGd836fAGzwF12Ug27mSc1enndRtQVW
pQTdnOnWuuRzOwEpd7x3xh9upACm4g==
=1CyJ
-----END PGP SIGNATURE-----
Merge tag 'pull-hex-20230518-1' of https://github.com/quic/qemu into staging
Hexagon update
# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCgAdFiEENjXHiM5iuR/UxZq0ewJE+xLeRCIFAmRmgQgACgkQewJE+xLe
# RCJLtAf8C/0kQRa4mjnbsztXuFyca53UxAv3BSBEDla4ZcMfFBoVJsGB3OP7IPXd
# KBQpkLyJAVye9idex5xqdp9nIfoGKDTsc6YtCfGujZ17cDpzLRDpHdUTex8PcZYK
# wpfM3hoVJsYRBMsojZ4OaxatjFQ+FWzrIH6FcgH086Q8TH4w9dZLNEJzHC4lOj0s
# 7qOuw2tgm+vOVlzsk/fv6/YD/BTeZTON3jgTPvAnvdRLb/482UpM9JkJ8E4rbte3
# Ss5PUK8QTQHU0yamspGy/PfsYxiptM+jIWGd836fAGzwF12Ug27mSc1enndRtQVW
# pQTdnOnWuuRzOwEpd7x3xh9upACm4g==
# =1CyJ
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 18 May 2023 12:48:24 PM PDT
# gpg: using RSA key 3635C788CE62B91FD4C59AB47B0244FB12DE4422
# gpg: Good signature from "Taylor Simpson (Rock on) <tsimpson@quicinc.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 3635 C788 CE62 B91F D4C5 9AB4 7B02 44FB 12DE 4422
* tag 'pull-hex-20230518-1' of https://github.com/quic/qemu: (44 commits)
Hexagon (linux-user/hexagon): handle breakpoints
Hexagon (gdbstub): add HVX support
Hexagon (gdbstub): fix p3:0 read and write via stub
Hexagon: add core gdbstub xml data for LLDB
gdbstub: add test for untimely stop-reply packets
gdbstub: only send stop-reply packets when allowed to
Remove test_vshuff from hvx_misc tests
Hexagon (decode): look for pkts with multiple insns at the same slot
Hexagon (iclass): update J4_hintjumpr slot constraints
Hexagon: append eflags to unknown cpu model string
Hexagon: list available CPUs with `-cpu help`
Hexagon (target/hexagon/*.py): raise exception on reg parsing error
target/hexagon: fix = vs. == mishap
Hexagon (target/hexagon) Additional instructions handled by idef-parser
Hexagon (target/hexagon) Move items to DisasContext
Hexagon (target/hexagon) Move pkt_has_store_s1 to DisasContext
Hexagon (target/hexagon) Move pred_written to DisasContext
Hexagon (target/hexagon) Move new_pred_value to DisasContext
Hexagon (target/hexagon) Move new_value to DisasContext
Hexagon (target/hexagon) Make special new_value for USR
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In the previous commit, we modified gdbstub.c to only send stop-reply
packets as a response to GDB commands that accept it. Now, let's add a
test for this intended behavior. Running this test before the fix from
the previous commit fails as QEMU sends a stop-reply packet
asynchronously, when GDB was in fact waiting an ACK.
Signed-off-by: Matheus Tavares Bernardino <quic_mathbern@quicinc.com>
Acked-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Taylor Simpson <tsimpson@quicinc.com>
Message-Id: <a30d93b9a8d66e9d9294354cfa2fc3af35f00202.1683214375.git.quic_mathbern@quicinc.com>
test_vshuff checks that the vshuff instruction works correctly when
both vector registers are the same. Using vshuff in this way is
undefined and will be rejected by the compiler in a future version of
the toolchain.
Signed-off-by: Marco Liebel <quic_mliebel@quicinc.com>
Reviewed-by: Brian Cain <bcain@quicinc.com>
Reviewed-by: Taylor Simpson <tsimpson@quicinc.com>
Tested-by: Taylor Simpson <tsimpson@quicinc.com>
Signed-off-by: Taylor Simpson <tsimpson@quicinc.com>
Message-Id: <20230509184231.2467626-1-quic_mliebel@quicinc.com>
Each slot in a packet can be assigned to at most one instruction.
Although the assembler generally ought to enforce this rule, we better
be safe than sorry and also do some check to properly throw an "invalid
packet" exception on wrong slot assignments.
This should also make it easier to debug possible future errors caused
by missing updates to `find_iclass_slots()` rules in
target/hexagon/iclass.c.
Co-authored-by: Taylor Simpson <tsimpson@quicinc.com>
Signed-off-by: Taylor Simpson <tsimpson@quicinc.com>
Signed-off-by: Matheus Tavares Bernardino <quic_mathbern@quicinc.com>
Reviewed-by: Taylor Simpson <tsimpson@quicinc.com>
Tested-by: Taylor Simpson <tsimpson@quicinc.com>
Message-Id: <f8b829443523568823d062adf8bf6659bc6d4a3f.1683552984.git.quic_mathbern@quicinc.com>
