Introduce support for emulating the MIPS Boston development board. The
Boston board is built around an FPGA & 3 PCIe controllers, one of which
is connected to an Intel EG20T Platform Controller Hub. It is used
during the development & debug of new CPUs and the software intended to
run on them, and is essentially the successor to the older MIPS Malta
board.
This patch does not implement the EG20T, instead connecting an already
supported ICH-9 AHCI controller. Whilst this isn't accurate it's enough
for typical stock Boston software (eg. Linux kernels) to work with hard
disks given that both the ICH-9 & EG20T implement the AHCI
specification.
Boston boards typically boot kernels in the FIT image format, and this
patch will treat kernels provided to QEMU as such. When loading a kernel
directly, the board code will generate minimal firmware much as the
Malta board code does. This firmware will set up the CM, CPC & GIC
register base addresses then set argument registers & jump to the kernel
entry point. Alternatively, bootloader code may be loaded using the bios
argument in which case no firmware will be generated & execution will
proceed from the start of the boot code at the default MIPS boot
exception vector (offset 0x1fc00000 into (c)kseg1).
Currently real Boston boards are always used with FPGA bitfiles that
include a Global Interrupt Controller (GIC), so the interrupt
configuration is only defined for such cases. Therefore the board will
only allow use of CPUs which implement the CPS components, including the
GIC, and will otherwise exit with a message.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
[yongbok.kim@imgtec.com:
isolated boston machine support for mips64el.
updated for recent Chardev changes.
ignore missing bios/kernel for qtest.
added default -drive to if=ide explicitly]
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Add support for emulating the Xilinx AXI Root Port Bridge for PCI
Express as described by Xilinx' PG055 document. This is a PCIe
controller that can be used with certain series of Xilinx FPGAs, and is
used on the MIPS Boston board which will make use of this code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
[yongbok.kim@imgtec.com:
removed returning on !level,
updated IRQ connection with GPIO logic,
moved xilinx_pcie_init() to boston.c
replaced stw_le_p() with pci_set_word()
and other cosmetic changes]
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Introduce support for loading Flattened Image Trees, as used by modern
U-Boot. FIT images are essentially flattened device tree files which
contain binary images such as kernels, FDTs or ramdisks along with one
or more configuration nodes describing boot configurations.
The MIPS Boston board typically boots kernels in the form of FIT images,
and will make use of this code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
[yongbok.kim@imgtec.com:
fixed potential memory leaks,
isolated building option]
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
In order to obtain fdt_first_subnode & fdt_next_subnode symbols from
libfdt for use by a later patch, bump the requirement for dtc to v1.4.2
& the submodule to that same version.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Provide a new cpu_supports_isa function which allows callers to
determine whether a CPU supports one of the ISA_ flags, by testing
whether the associated struct mips_def_t sets the ISA flags in its
insn_flags field.
An example use of this is to allow boards which generate bootloader code
to determine the properties of the CPU that will be used, for example
whether the CPU is 64 bit or which architecture revision it implements.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
If the GIC interrupt mask is changed by a write to the smask (set mask)
or rmask (reset mask) registers, we need to re-evaluate the state of the
pins/IRQs fed to the CPU. Without doing so we risk leaving a pin high
despite the interrupt that led to that state being masked, or losing
interrupts if an already pending interrupt is unmasked.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Provide a new function mips_gictimer_get_freq() which returns the
frequency at which a GIC timer will count. This will be useful for
boards which perform setup based upon this frequency.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Support moving the GCR base address & updating the CPU's CP0 CMGCRBase
register appropriately. This is required if a platform needs to move its
GCRs away from other memory, as the MIPS Boston development board does
to avoid its flash memory.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
The sheepdog URL is broken twice: First it uses a duplicated
http:// prefix, second the website seems to have moved to
https://sheepdog.github.io/sheepdog/ instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
If explicit zeroing out before mirroring is required for the target image,
it moves the block job offset counter to EOF, then offset and len counters
count the image size twice. There is no harm but stats are confusing,
specifically the progress of the operation is always reported as 99% by
management tools.
The patch skips offset increase for the first "technical" pass over the
image. This should not cause any further harm.
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1486045515-8009-1-git-send-email-den@openvz.org
CC: Jeff Cody <jcody@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
CC: Max Reitz <mreitz@redhat.com>
CC: Eric Blake <eblake@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
This adds blockdev-add support for iscsi devices.
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
This was previously only available with -iscsi. Again, after this patch,
the -iscsi option only takes effect if an URL is given. New users are
supposed to use the new driver-specific option.
All -iscsi options have a corresponding driver-specific option for the
iscsi block driver now.
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
This was previously only available with -iscsi. Again, after this patch,
the -iscsi option only takes effect if an URL is given. New users are
supposed to use the new driver-specific option.
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
This was previously only available with -iscsi. Again, after this patch,
the -iscsi option only takes effect if an URL is given. New users are
supposed to use the new driver-specific option.
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
This splits the logic in the old parse_chap() function into a part that
parses the -iscsi options into the new driver-specific options, and
another part that actually applies those options (called apply_chap()
now).
Note that this means that username and password specified with -iscsi
only take effect when a URL is provided. This is intentional, -iscsi is
a legacy interface only supported for compatibility, new users should
use the proper driver-specific options.
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
This introduces a .bdrv_parse_filename handler for iscsi which parses an
URL if given and translates it to individual options.
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
-----BEGIN PGP SIGNATURE-----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=/97H
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-block-2017-02-21' into staging
Changes to -drive without if= and with if=scsi
# gpg: Signature made Tue 21 Feb 2017 12:22:35 GMT
# gpg: using RSA key 0x3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-block-2017-02-21:
hw/i386: Deprecate -drive if=scsi with PC machine types
hw: Deprecate -drive if=scsi with non-onboard HBAs
hw/scsi: Concentrate -drive if=scsi auto-create in one place
hw: Drop superfluous special checks for orphaned -drive
blockdev: Make orphaned -drive fatal
blockdev: Improve message for orphaned -drive
hw/arm/highbank: Default -drive to if=ide instead of if=scsi
hw: Default -drive to if=none instead of scsi when scsi cannot work
hw: Default -drive to if=none instead of ide when ide cannot work
hw/arm/cubieboard hw/arm/xlnx-ep108: Fix units_per_default_bus
hw: Default -drive to if=ide explicitly where it works
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The PC machines (pc-q35-* pc-i440fx-* pc-* isapc xenfv) automatically
create lsi53c895a SCSI HBAs and SCSI devices to honor -drive if=scsi.
For giggles, try -drive if=scsi,bus=25,media=cdrom --- this makes QEMU
create 25 of them.
lsi53c895a is thoroughly obsolete (PCI Ultra2 SCSI, ca. 2000), and
currently has no maintainer in QEMU. megasas is a better choice,
except with old OSes that lack drivers. virtio-scsi is a much better
choice when you have a driver, but only (newish) Linux comes with one
in the box. There is no good default that works for all guests.
Encourage users to pick a non-obsolete SCSI HBA that works for them by
deprecating -drive if=scsi.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1487161136-9018-4-git-send-email-armbru@redhat.com>
Acked-By: Paolo Bonzini <pbonzini@redhat.com>
Block backends defined with "-drive if=T" with T other than "none" are
meant to be picked up by machine initialization code: a suitable
frontend gets created and wired up automatically.
Drives defined with if=scsi are also picked up by SCSI HBAs added with
-device, unlike other interface types. Deprecate this usage, as follows.
Create the frontends for onboard HBAs in machine initialization code,
exactly like we do for if=ide and other interface types. Change
scsi_legacy_handle_cmdline() to create a frontend only when it's still
missing, and warn that this usage is deprecated.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1487161136-9018-3-git-send-email-armbru@redhat.com>
The logic to create frontends for -drive if=scsi is in SCSI HBAs. For
all other interface types, it's in machine initialization code.
A few machine types create the SCSI HBAs necessary for that. That's
also not done for other interface types.
I'm going to deprecate these SCSI eccentricities. In preparation for
that, create the frontends in main() instead of the SCSI HBAs, by
calling new function scsi_legacy_handle_cmdline() there.
Note that not all SCSI HBAs create frontends. Take care not to change
that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1487161136-9018-2-git-send-email-armbru@redhat.com>
Acked-By: Paolo Bonzini <pbonzini@redhat.com>
We've traditionally rejected orphans here and there, but not
systematically. For instance, the sun4m machines have an onboard SCSI
HBA (bus=0), and have always rejected bus>0. Other machines with an
onboard SCSI HBA don't.
Commit a66c9dc made all orphans trigger a warning, and the previous
commit turned this into an error. The checks "here and there" are now
redundant. Drop them.
Note that the one in mips_jazz.c was wrong: it rejected bus > MAX_FD,
but MAX_FD is the number of floppy drives per bus.
Error messages change from
$ qemu-system-x86_64 -drive if=ide,bus=2
qemu-system-x86_64: Too many IDE buses defined (3 > 2)
$ qemu-system-mips64 -M magnum,accel=qtest -drive if=floppy,bus=2,id=fd1
qemu: too many floppy drives
$ qemu-system-sparc -M LX -drive if=scsi,bus=1
qemu: too many SCSI bus
to
$ qemu-system-x86_64 -drive if=ide,bus=2
qemu-system-x86_64: -drive if=ide,bus=2: machine type does not support if=ide,bus=2,unit=0
$ qemu-system-mips64 -M magnum,accel=qtest -drive if=floppy,bus=2,id=fd1
qemu-system-mips64: -drive if=floppy,bus=2,id=fd1: machine type does not support if=floppy,bus=2,unit=0
$ qemu-system-sparc -M LX -drive if=scsi,bus=1
qemu-system-sparc: -drive if=scsi,bus=1: machine type does not support if=scsi,bus=1,unit=0
Cc: John Snow <jsnow@redhat.com>
Cc: "Hervé Poussineau" <hpoussin@reactos.org>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1487153147-11530-9-git-send-email-armbru@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Block backends defined with "-drive if=T" with T other than "none" are
meant to be picked up by machine initialization code: a suitable
frontend gets created and wired up automatically.
If machine initialization code doesn't comply, the block backend
remains unused. This triggers a warning since commit a66c9dc, v2.2.0.
Drives created by default are exempted; use -nodefaults to get rid of
them.
Turn this warning into an error.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1487153147-11530-8-git-send-email-armbru@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
We warn when a -drive isn't supported by the machine type (commit
a66c9dc):
$ qemu-system-x86_64 -S -display none -drive if=mtd
Warning: Orphaned drive without device: id=mtd0,file=,if=mtd,bus=0,unit=0
Improve this to point to the offending bit of configuration:
qemu-system-x86_64: -drive if=mtd: warning: machine type does not support if=mtd,bus=0,unit=0
Especially nice when it's hidden behind -readconfig foo.cfg:
qemu-system-x86_64:foo.cfg:140: warning: machine type does not support if=mtd,bus=0,unit=0
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1487153147-11530-7-git-send-email-armbru@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
These machines have no onboard SCSI HBA, and no way to plug one.
-drive if=scsi therefore cannot work. They do have an onboard IDE
controller (sysbus-ahci), but fail to honor if=ide.
Change their default to if=ide, and add a TODO comment on what needs
to be done to actually honor -drive if=ide.
Cc: Rob Herring <robh@kernel.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1487153147-11530-6-git-send-email-armbru@redhat.com>
Block backends defined with -drive if=scsi are meant to be picked up
by machine initialization code: a suitable frontend gets created and
wired up automatically.
if=scsi drives not picked up that way can still be used with -device
as if they had if=none, but that's unclean and best avoided. Unused
ones produce an "Orphaned drive without device" warning.
A few machine types default to if=scsi, even though they don't
actually have a SCSI HBA. This makes no sense. Change their default
to if=none. Affected machines:
* aarch64/arm: realview-pbx-a9 vexpress-a9 vexpress-a15 xilinx-zynq-a9
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <1487153147-11530-5-git-send-email-armbru@redhat.com>
Block backends defined with -drive if=ide are meant to be picked up by
machine initialization code: a suitable frontend gets created and
wired up automatically.
if=ide drives not picked up that way can still be used with -device as
if they had if=none, but that's unclean and best avoided. Unused ones
produce an "Orphaned drive without device" warning.
-drive parameter "if" is optional, and the default depends on the
machine type. If a machine type doesn't specify a default, the
default is "ide".
Many machine types implicitly default to if=ide that way, even though
they don't actually have an IDE controller. This makes no sense.
Change the implicit default to if=none. Affected machines:
* all targets: none
* aarch64/arm: akita ast2500 canon cheetah collie connex imx25
integratorcp kzm lm3s6965evb lm3s811evb mainstone musicpal n800 n810
netduino2 nuri palmetto realview romulus sabrelite smdkc210 sx1 sx1
verdex z2
* cris: axis-dev88
* i386/x86_64: xenpv
* lm32: lm32-evr lm32-uclinux milkymist
* m68k: an5206 dummy mcf5208evb
* microblaze/microblazeel: petalogix-ml605 petalogix-s3adsp1800
* mips/mips64/mips64el/mipsel: mipssim
* moxie: moxiesim
* or32: or32-sim
* ppc/ppc64/ppcemb: bamboo ref405ep taihu virtex-ml507
* ppc/ppc64: mpc8544ds ppce500
* sh4/sh4eb: shix
* sparc: leon3_generic
* sparc64: niagara
* tricore: tricore_testboard
* unicore32: puv3
* xtensa/xtensaeb: kc705 lx200 lx60 ml605 sim
None of these machines have an IDE controller, let alone code to
honor if=ide.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Cc: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: xen-devel@lists.xensource.com
Cc: Michael Walle <michael@walle.cc>
Cc: Laurent Vivier <laurent@vivier.eu>
Cc: Anthony Green <green@moxielogic.com>
Cc: Jia Liu <proljc@gmail.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: qemu-ppc@nongnu.org
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Fabien Chouteau <chouteau@adacore.com>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Artyom Tarasenko <atar4qemu@gmail.com>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-By: Artyom Tarasenko <atar4qemu@gmail.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1487153147-11530-4-git-send-email-armbru@redhat.com>
Machine types cubieboard, xlnx-ep108, xlnx-zcu102 have an onboard AHCI
controller, but neglect to set their MachineClass member
units_per_default_bus = 1. This permits -drive if=ide,unit=1, which
makes no sense for AHCI. It also screws up index=N for odd N, because
it gets desugared to unit=1,bus=N/2
Doesn't really matter, because these machine types fail to honor
-drive if=ide. Add the missing units_per_default_bus = 1 anyway,
along with a TODO comment on what needs to be done for -drive if=ide.
Also set block_default_type = IF_IDE explicitly. It's currently the
default, but the next commit will change it to something more
sensible, and we want to keep the IF_IDE default for these three
machines. See also the previous commit.
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <1487153147-11530-3-git-send-email-armbru@redhat.com>
Block backends defined with -drive if=ide are meant to be picked up by
machine initialization code: a suitable frontend gets created and
wired up automatically.
if=ide drives not picked up that way can still be used with -device as
if they had if=none, but that's unclean and best avoided. Unused ones
produce an "Orphaned drive without device" warning.
-drive parameter "if" is optional, and the default depends on the
machine type. If a machine type doesn't specify a default, the
default is "ide".
Many machine types default to if=ide, even though they don't actually
have an IDE controller. A future patch will change these defaults to
something more sensible. To prepare for it, this patch makes default
"ide" explicit for the machines that actually pick up if=ide drives:
* alpha: clipper
* arm/aarch64: spitz borzoi terrier tosa
* i386/x86_64: generic-pc-machine (with concrete subtypes pc-q35-*
pc-i440fx-* pc-* isapc xenfv)
* mips64el: fulong2e
* mips/mipsel/mips64el: malta mips
* ppc/ppc64: mac99 g3beige prep
* sh4/sh4eb: r2d
* sparc64: sun4u sun4v
Note that ppc64 machine powernv already sets an "ide" default
explicitly. Its IDE controller isn't implemented, yet.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1487153147-11530-2-git-send-email-armbru@redhat.com>
v2:
* Rebased to resolve scsi conflicts
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYrCroAAoJEJykq7OBq3PIpJAH/1nvSNr8IRrEWFXuHxHlwqXo
opt8PZm1BhKLwKoZ7qwttWk8oxWV+VBRZcnLnm1+chmIqzwbeUVo8nzFwPbv1kB3
2x3uLz+3Qn0uln9v43alK5mHZk7wpGCshFBn3jkxdltzZX9vIaG+8IkKsgkS+IiC
MkUPFfoY/wRQq+eyBvhe6xPHoIlKa++LeQdRQ4kayvaixW1dn4Hbvj/vLAAG1nKL
HcEtO3EddEgkIvX5yztOWNKvEPqcYes7Ki207CjH8GXj4Ygmn4dBebDq+GR0NYwm
EXERuJJiPEbSLFknffwioVfllWKCVwg7oFaIuz6ysxVGFwFZSdn83CTjK+FbtFU=
=k9gD
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/block-pull-request' into staging
Pull request
v2:
* Rebased to resolve scsi conflicts
# gpg: Signature made Tue 21 Feb 2017 11:56:24 GMT
# gpg: using RSA key 0x9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha/tags/block-pull-request: (24 commits)
coroutine-lock: make CoRwlock thread-safe and fair
coroutine-lock: add mutex argument to CoQueue APIs
coroutine-lock: place CoMutex before CoQueue in header
test-aio-multithread: add performance comparison with thread-based mutexes
coroutine-lock: add limited spinning to CoMutex
coroutine-lock: make CoMutex thread-safe
block: document fields protected by AioContext lock
async: remove unnecessary inc/dec pairs
aio-posix: partially inline aio_dispatch into aio_poll
block: explicitly acquire aiocontext in aio callbacks that need it
block: explicitly acquire aiocontext in bottom halves that need it
block: explicitly acquire aiocontext in callbacks that need it
block: explicitly acquire aiocontext in timers that need it
aio: push aio_context_acquire/release down to dispatching
qed: introduce qed_aio_start_io and qed_aio_next_io_cb
blkdebug: reschedule coroutine on the AioContext it is running on
coroutine-lock: reschedule coroutine on the AioContext it was running on
nbd: convert to use qio_channel_yield
io: make qio_channel_yield aware of AioContexts
io: add methods to set I/O handlers on AioContext
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds a CoMutex around the existing CoQueue. Because the write-side
can just take CoMutex, the old "writer" field is not necessary anymore.
Instead of removing it altogether, count the number of pending writers
during a read-side critical section and forbid further readers from
entering.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20170213181244.16297-7-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
All that CoQueue needs in order to become thread-safe is help
from an external mutex. Add this to the API.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20170213181244.16297-6-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This will avoid forward references in the next patch. It is also
more logical because CoQueue is not anymore the basic primitive.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20170213181244.16297-5-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add two implementations of the same benchmark as the previous patch,
but using pthreads. One uses a normal QemuMutex, the other is Linux
only and implements a fair mutex based on MCS locks and futexes.
This shows that the slower performance of the 5-thread case is due to
the fairness of CoMutex, rather than to coroutines. If fairness does
not matter, as is the case with two threads, CoMutex can actually be
faster than pthreads.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20170213181244.16297-4-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Running a very small critical section on pthread_mutex_t and CoMutex
shows that pthread_mutex_t is much faster because it doesn't actually
go to sleep. What happens is that the critical section is shorter
than the latency of entering the kernel and thus FUTEX_WAIT always
fails. With CoMutex there is no such latency but you still want to
avoid wait and wakeup. So introduce it artificially.
This only works with one waiters; because CoMutex is fair, it will
always have more waits and wakeups than a pthread_mutex_t.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20170213181244.16297-3-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This uses the lock-free mutex described in the paper '"Blocking without
Locking", or LFTHREADS: A lock-free thread library' by Gidenstam and
Papatriantafilou. The same technique is used in OSv, and in fact
the code is essentially a conversion to C of OSv's code.
[Added missing coroutine_fn in tests/test-aio-multithread.c.
--Stefan]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20170213181244.16297-2-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170213135235.12274-19-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Pull the increment/decrement pair out of aio_bh_poll and into the
callers.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170213135235.12274-18-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch prepares for the removal of unnecessary lockcnt inc/dec pairs.
Extract the dispatching loop for file descriptor handlers into a new
function aio_dispatch_handlers, and then inline aio_dispatch into
aio_poll.
aio_dispatch can now become void.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170213135235.12274-17-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170213135235.12274-16-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170213135235.12274-15-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This covers both file descriptor callbacks and polling callbacks,
since they execute related code.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170213135235.12274-14-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170213135235.12274-13-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The AioContext data structures are now protected by list_lock and/or
they are walked with FOREACH_RCU primitives. There is no need anymore
to acquire the AioContext for the entire duration of aio_dispatch.
Instead, just acquire it before and after invoking the callbacks.
The next step is then to push it further down.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170213135235.12274-12-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
qed_aio_start_io and qed_aio_next_io will not have to acquire/release
the AioContext, while qed_aio_next_io_cb will. Split the functionality
and gain a little type-safety in the process.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170213135235.12274-11-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Keep the coroutine on the same AioContext. Without this change,
there would be a race between yielding the coroutine and reentering it.
While the race cannot happen now, because the code only runs from a single
AioContext, this will change with multiqueue support in the block layer.
While doing the change, replace custom bottom half with aio_co_schedule.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170213135235.12274-10-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
As a small step towards the introduction of multiqueue, we want
coroutines to remain on the same AioContext that started them,
unless they are moved explicitly with e.g. aio_co_schedule. This patch
avoids that coroutines switch AioContext when they use a CoMutex.
For now it does not make much of a difference, because the CoMutex
is not thread-safe and the AioContext itself is used to protect the
CoMutex from concurrent access. However, this is going to change.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170213135235.12274-9-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In the client, read the reply headers from a coroutine, switching the
read side between the "read header" coroutine and the I/O coroutine that
reads the body of the reply.
In the server, if the server can read more requests it will create a new
"read request" coroutine as soon as a request has been read. Otherwise,
the new coroutine is created in nbd_request_put.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170213135235.12274-8-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Support separate coroutines for reading and writing, and place the
read/write handlers on the AioContext that the QIOChannel is registered
with.
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20170213135235.12274-7-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
