This patch converts the ISA MMIO bridge code to always use little endian mmio.
All bswap code that existed was only there to convert from native cpu
endianness to little endian ISA devices.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
As stated before, devices can be little, big or native endian. The
target endianness is not of their concern, so we need to push things
down a level.
This patch adds a parameter to cpu_register_io_memory that allows a
device to choose its endianness. For now, all devices simply choose
native endian, because that's the same behavior as before.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Sending ESP a command caused it to trigger DMA immediately
even if DMA was not enabled at the DMA controller.
Add a signal from DMA controller to ESP to tell ESP about changes in
DMA enable bit. Also use the correct function for setting up GPIO outputs.
This fixes NetBSD 1.6.1 through 3.0 boot.
Thanks to Artyom Tarasenko for extensive debugging of the problem.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Changing block.h or blockdev.h resulted in recompiling most objects.
Move DriveInfo typedef and BlockInterfaceType enum definitions
to qemu-common.h and rearrange blockdev.h use to decrease churn.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
These will be used to generate unique id strings for ramblocks. The name
field is required, the device pointer is optional as most callers don't
have a device. When there's no device or the device isn't a child of
a bus implementing BusInfo.get_dev_path, the name should be unique for
the platform.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
System architecture dictates whether HAS_AUDIO is defined. It's then
useless to check for HAS_AUDIO in files which are only used on those
architectures which always have audio.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Allow the intercept the RTC IRQ for the HPET legacy mode. Then push
routing to IRQ8 completely into the HPET. This allows to turn
hpet_in_legacy_mode() into a private function. Furthermore, this stops
the RTC from clearing IRQ8 even if the HPET is in control.
This patch comes with a side effect: The RTC timers will no longer be
stoppend when there is no IRQ consumer, possibly causing a minor
performance degration. But as the guest may want to redirect the RTC to
the SCI in that mode, it should normally disable unused IRQ source
anyway.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
To match rtc_xxx with qdev, make rtc_xxx accept and return ISADevice
instead of RTCState.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
As i8259 in mips_jazz.c is not correctly connected to the isa bus, the
mc146818rtc isa devices fails to be created.
Signed-off-by: Roy Tam <roytam@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
We now only assign strdup()ed strings to these fields, never static
strings.
aliguori: fix build for ppc_prep and mips_jazz
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
In the very least, a change like this requires discussion on the list.
The naming convention is goofy and it causes a massive merge problem. Something
like this _must_ be presented on the list first so people can provide input
and cope with it.
This reverts commit 99a0949b72.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The CPU state parameter is not used, remove it and adjust callers. Now we
can compile ioport.c once for all targets.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Callers must pass ELF machine, byte swapping and symbol LSB clearing
information to ELF loader. A.out loader needs page size information, pass
that too as a parameter.
Extract prototypes to a separate file. Move loader.[ch] and elf_ops.h under hw.
Adjust callers. Also use target_phys_addr_t instead of target_ulong for
addresses: loader addresses aren't virtual.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Changes:
(1) make isa-bus maintain isa irqs, complain when allocating
already taken irqs.
(2) note that (1) works only for isa devices converted to qdev
already (floppy and ps2/kbd/mouse right now), so more work
is needed to make this really useful.
(3) split floppy init into isa and sysbus versions.
(4) add sysbus->isa bridge & fix -M isapc breakage.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
First step cleaning up the drives handling. This one does nothing but
removing drives_table[], still it became seriously big.
drive_get_index() is gone and is replaced by drives_get() which hands
out DriveInfo pointers instead of a table index. This needs adaption in
*tons* of places all over.
The drives are now maintained as linked list.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This reverts commit 8217606e6e (and
updates later added users of qemu_register_reset), we solved the
problem it originally addressed less invasively.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The parameter is always zero except when registering the three internal
io regions (ROM, unassigned, notdirty). Remove the parameter to reduce
the API's power, thus facilitating future change.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add the parameter 'order' to qemu_register_reset and sort callbacks on
registration. On system reset, callbacks with lower order will be
invoked before those with higher order. Update all existing users to the
standard order 0.
Note: At least for x86, the existing users seem to assume that handlers
are called in their registration order. Therefore, the patch preserves
this property. If someone feels bored, (s)he could try to identify this
dependency and express it properly on callback registration.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The vga_ram_size argument to machine init functions always has the same
value, and is ignored by many machines (including SPARC32 which has an
obsolete ifdef for VGA_RAM_SIZE).
Remove it and push VGA_RAM_SIZE into vga_int.h.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Now we can safely call AUD_init multiple times we can push it down to
individual audio devices, rather than having to pass it from the board
init.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Failure to initialize the audio subsystem is not handled consistently.
Where it is handled it has guest visible effects, which is wrong.
We already have a "nosound" audio driver as a last resort, so trying to
proceed without an audio backend seems pointless.
Also protect against multiple calls to AUD_init so that this can be
pushed down into individual devices.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Attached patch adds emulation of a SONIC netcard. This card has been used
in MIPS Jazz machines and in some Apple Mac 68K.
Emulation has been done using dp83932 specification, but can be enhanced
(if needed) to also emulate dp83916, dp83934 or dp83936 chipsets.
This has been tested in Linux 2.1, NetBSD 1.6.2 and MS Windows NT/MIPS
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@7112 c046a42c-6fe2-441c-8c8c-71466251a162
At the moment, rc4030 init function is returning some function pointers.
Mark them non-static and define them in header file instead.
Export also a function to read/write DMA memory, it will be required by
the netcard.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@7072 c046a42c-6fe2-441c-8c8c-71466251a162
All archs have some kind of firmware to load and can be fine with it
already. So there is not much use in enforcing the presence of a disk.
If the system setup requires one, the user will notice it anyway once
the firmware/bios fails to boot from it.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6899 c046a42c-6fe2-441c-8c8c-71466251a162
On the MIPS Magnum, the time that is held in the RTC's NVRAM should be
relative to midnight on 1980-01-01. This patch adds an extra parameter
to rtc_init(), allowing different epochs to be used. For the Magnum,
1980 is specified, and for all other machines, 2000 is specified.
I've not modified the handling of the century byte, as with an epoch of
1980 and a year of 2009, one could argue that it should hold either
0, 1, 19 or 20. NT 3.50 on MIPS does not read the century byte.
Signed-off-by: Stuart Brady <stuart.brady@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6429 c046a42c-6fe2-441c-8c8c-71466251a162
This patch improves G364 video card emulation (used in MIPS Magnum machine):
- Use memory dirty tracking to not refresh whole screen each time
- Use macros for debugging messages
- Add support for hardware cursor
- Handle Y-panning
- Raise irq at each screen redraw
- Support retrieving of some registers
- Add load/save support
The emulation has been tested in Linux 2.1 and Windows NT 3.5, in
640x480, 800x600, 1024x768 and 1280x1024 resolutions.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6356 c046a42c-6fe2-441c-8c8c-71466251a162
Patch 5/7
This patch changes the graphical_console_init function to return an
allocated DisplayState instead of a QEMUConsole.
This patch contains just the graphical_console_init change and few other
modifications mainly in console.c and vl.c.
It was necessary to move the display frontends (e.g. sdl and vnc)
initialization after machine->init in vl.c.
This patch does *not* include any required changes to any device, these
changes come with the following patches.
Patch 6/7
This patch changes the QEMUMachine init functions not to take a
DisplayState as an argument because is not needed any more;
In few places the graphic hardware initialization function was called
only if DisplayState was not NULL, now they are always called.
Apart from these cases, the rest are all mechanical substitutions.
Patch 7/7
This patch updates the graphic device code to use the new
graphical_console_init function.
As for the previous patch, in few places graphical_console_init was called
only if DisplayState was not NULL, now it is always called.
Apart from these cases, the rest are all mechanical substitutions.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6344 c046a42c-6fe2-441c-8c8c-71466251a162
Attached patch implements DMA support to RC4030 chipset and simplifies
jazz IO part (at 0xf0000000), where registers contain 16 bit values.
Config register has not a clear meaning (only one value is always valid,
and sometimes another one), so use a magic value instead.
The patch also wires DMA transfers for the SCSI adapter in the Jazz
emulation (Mips Magnum 4000 and Acer Pica 61).
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6145 c046a42c-6fe2-441c-8c8c-71466251a162
Current implementation of memory-mapped i8042 controller is atm
implemented with an interface shift (it_shift) parameter, like most all
memory-mapped devices in Qemu.
However, this isn't suitable for MIPS Magnum, where i8042 controller is at
0x80005000 up to 0x80005fff.
Thomas Bogendoerfer (from #mipslinux) tested the behaviour of a real
machine, and found that odd addresses are for status/command register, and
even addresses for data register.
Attached patch implements this behaviour by replacing the it_shift
parameter by a mask one.
Incidentally, keyboard now works on OpenBSD 2.3, which accesses i8042
controller at 0x80005060 and 0x80005061.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5962 c046a42c-6fe2-441c-8c8c-71466251a162
Introduce a max_cpus per-machine variable, allowing individual boards
to limit it's number of CPUs. Check requested number of CPUs in setup
code and exit if it exceeds the supported number for the machine.
This also renders the static MAX_CPUS check obsolete, so remove this
from vl.c.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5443 c046a42c-6fe2-441c-8c8c-71466251a162
