PIIX_NUM_PIC_IRQS is assumed to be the same as ISA_NUM_IRQS, otherwise
inconsistencies can occur.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20231007123843.127151-5-shentey@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
qbus_new() should not be called on unrealized device.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20231019071611.98885-9-philmd@linaro.org>
pcspk_init() is a legacy init function, inline and remove it.
Since the device is realized using &error_fatal, use the same
error for setting the "pit" link.
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20231019073307.99608-1-philmd@linaro.org>
This virtual method was always set to the x86-specific pc_madt_cpu_entry(),
even in piix4 which is also used in MIPS. The previous changes use
pc_madt_cpu_entry() otherwise, so madt_cpu can be dropped.
Since pc_madt_cpu_entry() is now only used in x86-specific code, the stub
in hw/acpi/acpi-x86-stub can be removed as well.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230908084234.17642-4-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As noted in the comment, the PCI INTx lines are supposed to be routed
to *both* the PIC and the I/O APIC. It's just that we don't cope with
the concept of an IRQ being asserted to two *different* pins on the
two irqchips.
So we have this hack of routing to I/O APIC only if the PIRQ routing to
the PIC is disabled. Which seems to work well enough, even when I try
hard to break it with kexec. But should be explicitly documented and
understood.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Message-Id: <112a09643b8191c4eae7d92fa247a861ab90a9ee.camel@infradead.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now that via_isa_set_irq() is unused it can be removed.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20230531211043.41724-4-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Resolves circular depencency between IDE function and south bridge.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20230531211043.41724-3-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
We use the user_ss[] array to hold the user emulation sources,
and the softmmu_ss[] array to hold the system emulation ones.
Hold the latter in the 'system_ss[]' array for parity with user
emulation.
Mechanical change doing:
$ sed -i -e s/softmmu_ss/system_ss/g $(git grep -l softmmu_ss)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230613133347.82210-10-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Allows the struct to be embedded directly into device models without additional
allocation.
Suggested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230612081238.1742-3-shentey@gmail.com>
[PMD: Update MAINTAINERS entry and use SPDX license identifier]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
During the last patches, TYPE_PIIX3_XEN_DEVICE turned into a clone of
TYPE_PIIX3_DEVICE. Remove this redundancy.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Tested-by: Chuck Zmudzinski <brchuckz@aol.com>
Message-Id: <20230312120221.99183-7-shentey@gmail.com>
Message-Id: <20230403074124.3925-8-shentey@gmail.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
The previous patch unified handling of piix3_write_config() accross the
PIIX3 device models which allows for assigning k->config_write once in the
base class.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Tested-by: Chuck Zmudzinski <brchuckz@aol.com>
Message-Id: <20230312120221.99183-6-shentey@gmail.com>
Message-Id: <20230403074124.3925-7-shentey@gmail.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Subscribe to pci_bus_fire_intx_routing_notifier() instead which allows for
having a common piix3_write_config() for the PIIX3 device models.
While at it, move the subscription into machine code to facilitate resolving
TYPE_PIIX3_XEN_DEVICE.
In a possible future followup, pci_bus_fire_intx_routing_notifier() could
be adjusted in such a way that subscribing to it doesn't require
knowledge of the device firing it.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Tested-by: Chuck Zmudzinski <brchuckz@aol.com>
Message-Id: <20230312120221.99183-5-shentey@gmail.com>
Message-Id: <20230403074124.3925-6-shentey@gmail.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
xen_intx_set_irq() doesn't depend on PIIX3State. In order to resolve
TYPE_PIIX3_XEN_DEVICE and in order to make Xen agnostic about the
precise south bridge being used, set up Xen's PCI IRQ handling of PIIX3
in the board.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Tested-by: Chuck Zmudzinski <brchuckz@aol.com>
Message-Id: <20230312120221.99183-4-shentey@gmail.com>
Message-Id: <20230403074124.3925-5-shentey@gmail.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This is a preparational patch for the next one to make the following
more obvious:
First, pci_bus_irqs() is now called twice in case of Xen where the
second call overrides the pci_set_irq_fn with the Xen variant.
Second, pci_bus_set_route_irq_fn() is now also called in Xen mode.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Tested-by: Chuck Zmudzinski <brchuckz@aol.com>
Message-Id: <20230312120221.99183-3-shentey@gmail.com>
Message-Id: <20230403074124.3925-4-shentey@gmail.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
xen_piix3_set_irq() isn't PIIX specific: PIIX is a single PCI device
while xen_piix3_set_irq() maps multiple PCI devices to their respective
IRQs, which is board-specific. Rename xen_piix3_set_irq() to communicate
this.
Also rename XEN_PIIX_NUM_PIRQS to XEN_IOAPIC_NUM_PIRQS since the Xen's
IOAPIC rather than PIIX has this many interrupt routes.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Tested-by: Chuck Zmudzinski <brchuckz@aol.com>
Message-Id: <20230312120221.99183-2-shentey@gmail.com>
Message-Id: <20230403074124.3925-2-shentey@gmail.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
The attribute isn't used since commit 5c9736789b
"i82378: Cleanup implementation".
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20230523195608.125820-4-shentey@gmail.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
We are going to require the macro from other files, too, so move
this #define to the header file.
Message-Id: <20230512124033.502654-9-thuth@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Just like in the real hardware (and in PIIX4), create the RTC
controllers in the south bridges.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230519084734.220480-2-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Several features that landed at the last possible moment:
Passthrough HDM decoder emulation
Refactor cryptodev
RAS error emulation and injection
acpi-index support on non-hotpluggable slots
Dynamically switch to vhost shadow virtqueues at vdpa net migration
Plus a couple of bugfixes that look important to have in the release.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmQJ8TYPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRp37YIAMpQA5/ddmKKz/ABtBMHB5JX/SVYcG+1xkBR
j9IFYusOfmmDfmgAhv0Qxi9+Wik95lszVZUnphvocSGd0PXH47pK7yv9RZ1ttaYX
oAbXrGqXo8rUhl1ksQsJ8Iasj2di1BLP0byPuozbRkg1Kkz5TqRd9+hBqSBGEx21
tsP5708UVCDAriwYYO78Cx0ZasmB9bqqeom5FdEsg9sYJ5aElOOvitp9YO1p2xhU
gRvhD+k/aqNi+mfOUF7qGDBanxKgx75VV/KU1cjjS9R1vNtwRhfc/26PBrROY00a
wkZWnAxmzDFKRS6cEfeb+eDGEVjC3IqLAjcFeuAIT/78CwdvIiY=
=e1yv
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: features, fixes
Several features that landed at the last possible moment:
Passthrough HDM decoder emulation
Refactor cryptodev
RAS error emulation and injection
acpi-index support on non-hotpluggable slots
Dynamically switch to vhost shadow virtqueues at vdpa net migration
Plus a couple of bugfixes that look important to have in the release.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmQJ8TYPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRp37YIAMpQA5/ddmKKz/ABtBMHB5JX/SVYcG+1xkBR
# j9IFYusOfmmDfmgAhv0Qxi9+Wik95lszVZUnphvocSGd0PXH47pK7yv9RZ1ttaYX
# oAbXrGqXo8rUhl1ksQsJ8Iasj2di1BLP0byPuozbRkg1Kkz5TqRd9+hBqSBGEx21
# tsP5708UVCDAriwYYO78Cx0ZasmB9bqqeom5FdEsg9sYJ5aElOOvitp9YO1p2xhU
# gRvhD+k/aqNi+mfOUF7qGDBanxKgx75VV/KU1cjjS9R1vNtwRhfc/26PBrROY00a
# wkZWnAxmzDFKRS6cEfeb+eDGEVjC3IqLAjcFeuAIT/78CwdvIiY=
# =e1yv
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 09 Mar 2023 14:46:14 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (72 commits)
virtio: fix reachable assertion due to stale value of cached region size
hw/virtio/vhost-user: avoid using unitialized errp
hw/pxb-cxl: Support passthrough HDM Decoders unless overridden
hw/pci: Add pcie_count_ds_port() and pcie_find_port_first() helpers
hw/mem/cxl_type3: Add CXL RAS Error Injection Support.
hw/pci/aer: Make PCIE AER error injection facility available for other emulation to use.
hw/cxl: Fix endian issues in CXL RAS capability defaults / masks
hw/mem/cxl-type3: Add AER extended capability
hw/pci-bridge/cxl_root_port: Wire up MSI
hw/pci-bridge/cxl_root_port: Wire up AER
hw/pci/aer: Add missing routing for AER errors
hw/pci/aer: Implement PCI_ERR_UNCOR_MASK register
pcihp: add ACPI PCI hotplug specific is_hotpluggable_bus() callback
pcihp: move fields enabling hotplug into AcpiPciHpState
acpi: pci: move out ACPI PCI hotplug generator from generic slot generator build_append_pci_bus_devices()
acpi: pci: move BSEL into build_append_pcihp_slots()
acpi: pci: drop BSEL usage when deciding that device isn't hotpluggable
pci: move acpi-index uniqueness check to generic PCI device code
tests: acpi: update expected blobs
tests: acpi: add non zero function device with acpi-index on non-hotpluggble bus
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add basic implementation of the AC'97 sound part used in VIA south
bridge chips. Not all features of the device is emulated, only one
playback channel is supported for now but this is enough to get sound
output from some guests using this device on pegasos2.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Volker Rümelin <vr_qemu@t-online.de>
Tested-by: Rene Engel <ReneEngel80@emailn.de>
Message-Id: <63b99410895312f40e7be479f581da0805e605a1.1678188711.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The real VIA south bridges implement a PCI IRQ router which is configured
by the BIOS or the OS. In order to respect these configurations, QEMU
needs to implement it as well. The real chip may allow routing IRQs from
internal functions independently of PCI interrupts but since guests
usually configute it to a single shared interrupt we don't model that
here for simplicity.
Note: The implementation was taken from piix4_set_irq() in hw/isa/piix4.
Suggested-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Tested-by: Rene Engel <ReneEngel80@emailn.de>
Message-Id: <fbb016c7d0e19093335c237e15f5f6c62c4393b4.1678188711.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
To be 'usable', QDev objects (which are QOM objects) must be
1/ initialized (at this point their properties can be modified), then
2/ realized (properties are consumed).
Some devices (objects) might depend on other devices. When creating
the 'QOM composition tree', parent objects can't be 'realized' until
all their children are. We might also have circular dependencies.
A common circular dependency occurs with IRQs. Device (A) has an
output IRQ wired to device (B), and device (B) has one to device (A).
When (A) is realized and connects its IRQ to an unrealized (B), the
IRQ handler on (B) is not yet created. QEMU pass IRQ between objects
as pointer. When (A) poll (B)'s IRQ, it is NULL. Later (B) is realized
and its IRQ pointers are populated, but (A) keeps a reference to a
NULL pointer.
A common pattern to bypass this circular limitation is to use 'proxy'
objects. Proxy (P) is created (and realized) before (A) and (B). Then
(A) and (B) can be created in different order, it doesn't matter: (P)
pointers are already populated.
Commit bb98e0f59c ("hw/isa/vt82c686: Remove intermediate IRQ
forwarder") neglected the QOM/QDev circular dependency issue, and
removed the 'proxy' between the southbridge, its PCI functions and the
interrupt controller, resulting in PCI functions wiring output IRQs to
'NULL', leading to guest failures (IRQ never delivered) [1] [2].
Since we are entering feature freeze, it is safer to revert the
offending patch until we figure a way to strengthen our APIs.
[1] https://lore.kernel.org/qemu-devel/928a8552-ab62-9e6c-a492-d6453e338b9d@redhat.com/
[2] https://lore.kernel.org/qemu-devel/cover.1677628524.git.balaton@eik.bme.hu/
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: Rene Engel <ReneEngel80@emailn.de>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <cdfb3c5a42e505450f6803124f27856434c5b298.1677628524.git.balaton@eik.bme.hu>
[PMD: Reworded description]
Inspired-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
To be 'usable', QDev objects (which are QOM objects) must be
1/ initialized (at this point their properties can be modified), then
2/ realized (properties are consumed).
Some devices (objects) might depend on other devices. When creating
the 'QOM composition tree', parent objects can't be 'realized' until
all their children are. We might also have circular dependencies.
A common circular dependency occurs with IRQs. Device (A) has an
output IRQ wired to device (B), and device (B) has one to device (A).
When (A) is realized and connects its IRQ to an unrealized (B), the
IRQ handler on (B) is not yet created. QEMU pass IRQ between objects
as pointer. When (A) poll (B)'s IRQ, it is NULL. Later (B) is realized
and its IRQ pointers are populated, but (A) keeps a reference to a
NULL pointer.
A common pattern to bypass this circular limitation is to use 'proxy'
objects. Proxy (P) is created (and realized) before (A) and (B). Then
(A) and (B) can be created in different order, it doesn't matter: (P)
pointers are already populated.
Commit cef2e7148e ("hw/isa/i82378: Remove intermediate IRQ forwarder")
neglected the QOM/QDev circular dependency issue, and removed the
'proxy' between the southbridge, its PCI functions and the interrupt
controller, resulting in PCI functions wiring output IRQs to
'NULL', leading to guest failures (IRQ never delivered) [1] [2].
Since we are entering feature freeze, it is safer to revert the
offending patch until we figure a way to strengthen our APIs.
[1] https://lore.kernel.org/qemu-devel/928a8552-ab62-9e6c-a492-d6453e338b9d@redhat.com/
[2] https://lore.kernel.org/qemu-devel/cover.1677628524.git.balaton@eik.bme.hu/
This reverts commit cef2e7148e.
Reported-by: Thomas Huth <thuth@redhat.com>
Inspired-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Provide pcihp specific callback to check if bus is hotpluggable
and consolidate its scattered hotplug criteria there.
While at it clean up no longer needed
qbus_set_hotplug_handler(BUS(bus), NULL)
workarounds since callback makes qbus_is_hotpluggable() return
correct answer even if hotplug_handler is set on bus.
PS:
see ("pci: fix 'hotplugglable' property behavior") for details
why callback was introduced.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230302161543.286002-35-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
RTCState only represents a Motorola MC146818 model,
not any RTC chipset. Rename the structure as MC146818RtcState
using:
$ sed -i -e s/RTCState/MC146818RtcState/g $(git grep -wl RTCState)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230210233116.80311-2-philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
isa_get_irq() was added in commit 3a38d437ca
("Add isa_reserve_irq()" Fri Aug 14 11:36:15 2009) as:
a temporary interface to be used to allocate ISA IRQs for
devices which have not yet been converted to qdev, and for
special cases which are not suited for qdev conversions,
such as the 'ferr'.
We still use it 14 years later, using the global 'isabus'
singleton. In order to get rid of such *temporary* interface,
extract isa_bus_get_irq() which can take any ISABus* object.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230215161641.32663-3-philmd@linaro.org>
isa_get_dma() returns a DMA channel handler from an ISABus.
To emphasize this, rename it as isa_bus_get_dma().
Mechanical change using:
$ sed -i -e 's/isa_get_dma/isa_bus_get_dma/g' \
$(git grep -l isa_get_dma)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230215161641.32663-2-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230210163744.32182-11-philmd@linaro.org>
isa_bus_irqs() register an array of input IRQs on
the ISA bus. Rename it as isa_bus_register_input_irqs().
Mechanical change using:
$ sed -i -e 's/isa_bus_irqs/isa_bus_register_input_irqs/g' \
$(git grep -wl isa_bus_irqs)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230210163744.32182-10-philmd@linaro.org>
No point in inlining isa_bus_from_device() which is only
used at device realization time.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230210163744.32182-9-philmd@linaro.org>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
ISADeviceClass is an empty class and just increase code
complexity. Remove it, directly embedding DeviceClass in
classes expanding TYPE_ISA_DEVICE.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230215161641.32663-19-philmd@linaro.org>
Directly dispatch ISA IRQs to 'cpu_intr' output IRQ
by removing the intermediate via_isa_request_i8259_irq()
handler. Rename ISA IRQs array as 'isa_irqs_in' to
emphasize these are input IRQs.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230210163744.32182-5-philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
When the i82378 model was added in commit a04ff94097 ("prep:
Add i82378 PCI-to-ISA bridge emulation") the i8259 model was
not yet QOM'ified. This happened later in commit 747c70af78
("i8259: Convert to qdev").
Directly dispatch ISA IRQs to 'cpu_intr' output IRQ
by removing the intermediate i82378_request_out0_irq()
handler. Rename ISA IRQs array as 'isa_irqs_in' to
emphasize these are input IRQs.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230210163744.32182-4-philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Commit a04ff94097 ("prep: Add i82378 PCI-to-ISA bridge
emulation") aimed to model the 2 output IRQs: CPU intr
and NMI. Commit 5039d6e235 ("i8257: remove cpu_request_exit
irq") removed the NMI IRQ.
Since this model only use the CPU interrupt, replace the
'out[2]' array by a single 'cpu_intr'.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230210163744.32182-3-philmd@linaro.org>
ICH9 is a south bridge which doesn't necessarily depend on x86, so move
it into the southbridge folder, analoguous to PIIX.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230213173033.98762-13-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230213173033.98762-12-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Most code uses IOAPIC_NUM_PINS. The only place where GSI_NUM_PINS defines
the size of an array is ICH9LPCState::gsi which needs to match
IOAPIC_NUM_PINS. Remove GSI_NUM_PINS for consistency.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230213173033.98762-10-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
ich9_lpc_reset() is the dc->reset callback which is called
automatically. No need to call it explicitly during k->realize.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230213173033.98762-9-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Make TYPE_ICH9_LPC_DEVICE more self-contained by moving the call to
ich9_lpc_pm_init() from board code to its realize function. In order
to propagate x86_machine_is_smm_enabled(), introduce an "smm-enabled"
property like we have in piix4.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230213173033.98762-8-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
By using qdev_get_child_bus() we can eliminate ICH9LPCState::isa_bus and
spare the ich9_lpc variable in pc_q35, too.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230213173033.98762-4-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
No need to rely on the board to wire up the ICH9 PCI IRQs. All functions
access private state of the LPC device which suggests that it should
wire up the IRQs.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230213173033.98762-3-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Frees isa-bus.c from implicit ACPI dependency.
While at it, resolve open coding of qbus_build_aml() in piix3 and ich9.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230121151941.24120-3-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Suggested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20221204190553.3274-7-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
pci_map_irq_fn's in general seem to be board-specific, and PIIX4's
pci_slot_get_pirq() in particular seems very Malta-specific. So move the
latter to malta.c to 1/ keep the board logic in one place and 2/ avoid
PIIX4 to make assumptions about its board.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230109172347.1830-7-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
pci_map_irq_fn's in general seem to be board-specific. So move PIIX3's
pci_slot_get_pirq() to board code to not have PIIX3 make assuptions
about its board.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230109172347.1830-6-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
pci_bus_irqs() coupled together the assignment of pci_set_irq_fn and
pci_map_irq_fn to a PCI bus. This coupling gets in the way when the
pci_map_irq_fn is board-specific while the pci_set_irq_fn is device-
specific.
For example, both of QEMU's PIIX south bridge models have different
pci_map_irq_fn implementations which are board-specific rather than
device-specific. These implementations should therefore reside in board
code. The pci_set_irq_fn's, however, should stay in the device models
because they access memory internal to the model.
Factoring out pci_bus_map_irqs() from pci_bus_irqs() allows the
assignments to be decoupled, resolving the problem described above.
Note also how pci_vpb_realize() which gets touched in this commit
assigns different pci_map_irq_fn's depending on the board.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230109172347.1830-5-shentey@gmail.com>
[PMD: Factor out in vfu_object_set_bus_irq()]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
IRQRC[A:D] registers reset value is 0x80. We were forcing
the MIPS Malta machine routing to be able to boot a Linux
kernel without any bootloader.
We now have these registers initialized in the Malta machine
write_bootloader(), so we can use the correct reset values.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20221027204720.33611-4-philmd@linaro.org>
PCIDeviceClass and PCIDevice are defined in pci.h. Many users of the
header don't actually need them. Similar structs live in their own
headers: PCIBusClass and PCIBus in pci_bus.h, PCIBridge in
pci_bridge.h, PCIHostBridgeClass and PCIHostState in pci_host.h,
PCIExpressHost in pcie_host.h, and PCIERootPortClass, PCIEPort, and
PCIESlot in pcie_port.h.
Move PCIDeviceClass and PCIDeviceClass to new pci_device.h, along with
the code that needs them. Adjust include directives.
This also enables the next commit.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221222100330.380143-6-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The ACPIREGS are provided by TYPE_VIA_PM, so needs to select ACPI.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20221216130355.41667-6-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
ich9_lpc_realize() uses apm_init() and ich9_smbus_realize() uses
pm_smbus_init(), so both APM and ACPI_SMBUS are provided by the device
models managed by ACPI_ICH9.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221216130355.41667-3-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Although the ICH9 ACPI controller may currently be tied to x86 it
doesn't have to. Furthermore, the source files this configuration switch
manages contain a '9', so this name fits more.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221216130355.41667-2-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The TCO watchdog implementation default behaviour from POV of the
guest OS relies on the initial values for two I/O ports:
* TCO1_CNT == 0x0
Since bit 11 (TCO Timer Halt) is clear, the watchdog state
is considered to be initially running
* GCS == 0x20
Since bit 5 (No Reboot) is set, the watchdog will not trigger
when the timer expires
This is a safe default, because the No Reboot bit will prevent the
watchdog from triggering if the guest OS is unaware of its existance,
or is slow in configuring it. When a Linux guest initializes the TCO
watchdog, it will attempt to clear the "No Reboot" flag, and read the
value back. If the clear was honoured, the driver will treat this as
an indicator that the watchdog is functional and create the guest
watchdog device.
QEMU implements a second "no reboot" flag, however, via pin straps
which overrides the behaviour of the guest controlled "no reboot"
flag:
commit 5add35bec1
Author: Paulo Alcantara <pcacjr@gmail.com>
Date: Sun Jun 28 14:58:58 2015 -0300
ich9: implement strap SPKR pin logic
This second 'noreboot' pin was defaulted to high, which also inhibits
triggering of the requested watchdog actions, unless QEMU is launched
with the magic flag "-global ICH9-LPC.noreboot=false".
This is a bad default as we are exposing a watchdog to every guest OS
using the q35 machine type, but preventing it from actually doing what
it is designed to do. What is worse is that the guest OS and its apps
have no way to know that the watchdog is never going to fire, due to
this second 'noreboot' pin.
If a guest OS had no watchdog device at all, then apps whose operation
and/or data integrity relies on a watchdog can refuse to launch, and
alert the administrator of the problematic deployment. With Q35 machines
unconditionally exposing a watchdog though, apps will think their
deployment is correct but in fact have no protection at all.
This patch flips the default of the second 'no reboot' flag, so that
configured watchdog actions will be honoured out of the box for the
7.2 Q35 machine type onwards, if the guest enables use of the watchdog.
See also related bug reports
https://bugzilla.redhat.com/show_bug.cgi?id=2080207https://bugzilla.redhat.com/show_bug.cgi?id=2136889https://bugzilla.redhat.com/show_bug.cgi?id=2137346
Reviewed-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20221216125749.596075-5-berrange@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
These tracepoints aid in understanding and debugging the guest drivers
for the TCO watchdog.
Reviewed-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20221216125749.596075-3-berrange@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 47a373faa6 (acpi: pc/q35: drop ad-hoc PCI-ISA bridge AML routines and let bus ennumeration generate AML)
moved ISA bridge AML generation to respective devices and was using
aml_alias() to provide PRQx fields in _SB. scope. However, it turned
out that SeaBIOS was not able to process Alias opcode when parsing DSDT,
resulting in lack of keyboard during boot (SeaBIOS console, grub, FreeDOS).
While fix for SeaBIOS is posted
https://mail.coreboot.org/hyperkitty/list/seabios@seabios.org/thread/RGPL7HESH5U5JRLEO6FP77CZVHZK5J65/
fixed SeaBIOS might not make into QEMU-7.2 in time.
Hence this workaround that puts PRQx back into _SB scope
and gets rid of aliases in ISA bridge description, so
DSDT will be parsable by broken SeaBIOS.
That brings back hardcoded references to ISA bridge
PCI0.S08.P40C/PCI0.SF8.PIRQ
where middle part now is auto generated based on slot it's
plugged in, but it should be fine as bridge initialization
also hardcodes PCI address of the bridge so it can't ever
move. Once QEMU tree has fixed SeaBIOS blob, we should be able
to drop this part and revert back to alias based approach
Reported-by: Volker Rümelin <vr_qemu@t-online.de>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20221121153613.3972225-3-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PCI-ISA bridges that are built in PIIX/Q35 are building its own AML
using AcpiDevAmlIf interface. Now build_append_pci_bus_devices()
gained AcpiDevAmlIf interface support to get AML of devices atached
to PCI slots.
So drop ad-hoc build_q35_isa_bridge()/build_piix4_isa_bridge()
and let PCI bus enumeration to include PCI-ISA bridge AML
when it's enumerated by build_append_pci_bus_devices().
AML change is mostly contextual, which moves whole ISA hierarchy
directly under PCI host bridge instead of it being described
as separate \SB.PCI0.ISA block.
Note:
If bus/slot that hosts ISA bridge has BSEL set, it will gain new
ASUN and _DMS entries (i.e. acpi-index support, but it should not
cause any functional change and that is fine from PCI Firmware
spec point of view), potentially it's possible to suppress that
by adding a flag to PCIDevice but I don't see a reason to do that
yet, I'd rather treat bridge just as any other PCI device if it's
possible.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20221017102146.2254096-4-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For the VIA south bridges there was a comment to have the call in board code.
Move it there for PIIX4 as well for consistency.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20221022150508.26830-29-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
PIIX3 clears its reset control register, so do the same in PIIX4.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20221022150508.26830-28-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20221022150508.26830-27-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Suggested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221022150508.26830-9-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This method post-loads the southbridge, not the IDE device.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20221022150508.26830-8-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
get_system_memory() accesses global state while pci_address_space() uses
whatever has been passed to the device instance, so avoid the global.
Moreover, PIIX4 uses pci_address_space() here as well.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20221022150508.26830-7-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Rather than registering the reset handler via a function which
appends the handler to a global list, prefer to implement it as
a virtual method - PIIX4 does the same already.
Note that this means that piix3_reset can now also be called writing to
the relevant configuration space register on a PCI bridge.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20221022150508.26830-6-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
According to the PIIX3 datasheet, the reset control register is one byte in size.
Moreover, PIIX4 has it, so add it to PIIX3 as well.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20221022150508.26830-5-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Fixes the "extra-semi" clang-tidy check.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20221022150508.26830-4-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Just like in the real hardware (and in PIIX4), create the DMA
controllers in the south bridges.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20221022150508.26830-2-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
According to good QOM practice, an object should only deal with objects
of its own sub tree. Having devices create an alias on the machine
object doesn't respect this good practice. To resolve this, create the
alias in the machine's code.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220901114127.53914-14-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Embed the rtc in the host device, analoguous to the other child devices
and analoguous to PIIX4.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220901114127.53914-13-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The AC97 function's wakeup status is wired to the PM function and both
the AC97 and MC97 interrupt routing is determined by the ISA function.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220901114127.53914-11-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The PM controller has activity bits which monitor activity of other
built-in devices in the host device.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220901114127.53914-10-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The USB functions can be enabled/disabled through the ISA function. Also
its interrupt routing can be influenced there.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220901114127.53914-9-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The IDE function is closely tied to the ISA function (e.g. the IDE
interrupt routing happens there), so it makes sense that the IDE
function is instantiated within the south bridge itself.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220901114127.53914-7-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Rather than terminating abruptly, make use of the already present errp and
propagate the error to the caller.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220901114127.53914-5-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Unlike get_system_memory(), pci_address_space() respects the memory tree
available to the parent device.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220901114127.53914-4-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Now that also the super io device is realized in the common realize method,
the isa_bus attribute can be turned into a temporary.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220901114127.53914-3-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The object creation now happens in chip-specific init methods which
allows the realize methods to be consolidated into one method. Shifting
the logic into the init methods has the addidional advantage that the
parent object's init methods are called implicitly - like constructors
in object-oriented languages.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220901114127.53914-2-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
xen_piix_pci_write_config_client() is implemented in the xen sub tree and
uses PIIX constants internally, thus creating a direct dependency on
PIIX. Now that xen_set_pci_link_route() is stubbable, the logic of
xen_piix_pci_write_config_client() can be moved to PIIX which resolves
the dependency.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20220626094656.15673-3-shentey@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
During the previous changesets piix3_create() became a trivial
wrapper around more generic functions. Modernize the code.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220603185045.143789-12-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Modernizes the code.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220603185045.143789-11-shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
PCI interrupt wiring was performed in create() functions which are
obsolete. Move these tasks into QOM functions to modernize the code.
In order to avoid duplicate checking for xen_enabled() the realize
methods are now split.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220603185045.143789-10-shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The pci_map_irq_fn was implemented below type_init() which made it
inaccessible to QOM functions. So move it up.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220603185045.143789-9-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
During the previous changesets piix4_create() became a trivial
wrapper around more generic functions. Modernize the code.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220603185045.143789-8-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Just like the real hardware, create the PIIX4 ACPI controller as part of
the PIIX4 southbridge. This also mirrors how the IDE and USB functions
are already created.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220603185045.143789-7-shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Modernizes the code.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220603185045.143789-6-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
PCI interrupt wiring and device creation were performed in create()
functions which are obsolete. Move these tasks into QOM functions to
modernize the code.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220603185045.143789-5-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The pci_map_irq_fn was implemented below type_init() which made it
inaccessible to QOM functions. So move it up.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220603185045.143789-4-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220603185045.143789-3-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
TYPE_PIIX3_PCI_DEVICE resides there as already, so add the remaining
ones, too.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220603185045.143789-2-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Now that all external logic has been removed from piix4_pm_initfn() the PIIX4_PM
device can be instantiated directly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220528091934.15520-12-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Initialize the SMI IRQ in piix4_pm_init().
The smi_irq can now be wired up directly using a qdev gpio instead
of having to set the IRQ externally in piix4_pm_initfn().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220528091934.15520-10-mark.cave-ayland@ilande.co.uk>
[PMD: Partially squash 20220528091934.15520-8-mark.cave-ayland@ilande.co.uk]
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Introduce piix4_pm_init() instance init function and use it to
initialise the separate qdev gpio for the SCI IRQ.
The sci_irq can now be wired up directly using a qdev gpio instead
of having to set the IRQ externally in piix4_pm_initfn().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220528091934.15520-9-mark.cave-ayland@ilande.co.uk>
[PMD: Partially squash 20220528091934.15520-8-mark.cave-ayland@ilande.co.uk]
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
When QOMifying a device it is typical to use _init() as the suffix for an
instance_init function, however this name is already in use by the legacy
piix4_pm_init() wrapper function. Eventually the wrapper function will be
removed, but for now rename it to piix4_pm_initfn() to avoid a naming
collision.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220528091934.15520-7-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This exposes the PIIX4_PM device to the caller to allow any qdev gpios to be
mapped outside of piix4_pm_init().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220528091934.15520-6-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
replaces adhoc build_isa_devices_aml() with generic AcpiDevAmlIf
way to build bridge AML including all devices that are attached
to its ISA bus.
Later when PCI is converted to AcpiDevAmlIf, build_q35_isa_bridge()
will also be dropped since PCI parts itself will take care of
building device prologue/epilogue AML for each enumerated PCI device.
Expected AML change is contextual, where ISA devices are moved from
separately declared _SB.PCI0.ISA scope, directly under Device(ISA)
node.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220608135340.3304695-21-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
replaces ad-hoc build_isa_devices_aml() with generic AcpiDevAmlIf
way to build bridge AML including all devices that are attached to
its ISA bus.
Later when PCI is converted to AcpiDevAmlIf, build_piix4_isa_bridge()
will also be dropped since PCI parts itself will take care of
building device prologue/epilogue AML for each enumerated PCI
device.
Expected AML change is contextual, where ISA devices are moved
from separately declared _SB.PCI0.ISA scope , directly under
Device(ISA) node.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220608135340.3304695-20-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220608135340.3304695-9-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To allow incremental conversion from ISADeviceClass::build_aml
to AcpiDevAmlIf, add support for the later without removing
the former. Once conversion is complete, another commit will
drop ISADeviceClass::build_aml related code.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220608135340.3304695-3-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A global boolean variable "vga_interface_created"(declared in softmmu/globals.c)
has been used to track the creation of vga interface. If the vga flag is passed
in the command line "default_vga"(declared in softmmu/vl.c) variable is set to 0.
To warn user, the condition checks if vga_interface_created is false
and default_vga is equal to 0. If "-vga none" is passed, this patch will not warn the
user regarding the creation of VGA device.
The warning "A -vga option was passed but this
machine type does not use that option; no VGA device has been created"
is logged if vga flag is passed but no vga device is created.
This patch has been tested for x86_64, i386, sparc, sparc64 and arm boards.
Signed-off-by: Gautam Agrawal <gautamnagrawal@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/581
Message-Id: <20220501122505.29202-1-gautamnagrawal@gmail.com>
[thuth: Fix wrong warning with "-device" in some cases as reported by Paolo]
Signed-off-by: Thomas Huth <thuth@redhat.com>
isa_init_irq() has become a trivial one-line wrapper for isa_get_irq().
It can therefore be removed.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com> (tpm_tis_isa)
Acked-by: Corey Minyard <cminyard@mvista.com> (isa_ipmi_bt, isa_ipmi_kcs)
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220301220037.76555-8-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220307134353.1950-14-philippe.mathieu.daude@gmail.com>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Now that the last users of ISADevice::isairq[] have been resolved during the
previous commits, it can be removed for good.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220301220037.76555-7-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220307134353.1950-13-philippe.mathieu.daude@gmail.com>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
