There's no need for this to be dynamic, make it static.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20180212154903.8859-1-dgilbert@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Interactive boot menu for scsi. This follows a similar procedure
as the interactive menu for eckd dasd. An example follows:
s390x Enumerated Boot Menu.
3 entries detected. Select from index 0 to 2.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Added additional "break;" statement to avoid analyzer warnings]
Signed-off-by: Thomas Huth <thuth@redhat.com>
If no boot menu options are present, then flag the boot menu to
use the zipl options that were set in the zipl configuration file
(and stored on disk by zipl). These options are found at some
offset prior to the start of the zipl boot menu banner. The zipl
timeout value is limited to a 16-bit unsigned integer and stored
as seconds, so we take care to convert it to milliseconds in order
to conform to the rest of the boot menu functionality. This is
limited to CCW devices.
For reference, the zipl configuration file uses the following
fields in the menu section:
prompt=1 enable the boot menu
timeout=X set the timeout to X seconds
To explicitly disregard any boot menu options, then menu=off or
<bootmenu enable='no' ... /> must be specified.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Set boot menu options for an s390 guest and store them in
the iplb. These options are set via the QEMU command line
option:
-boot menu=on|off[,splash-time=X]
or via the libvirt domain xml:
<os>
<bootmenu enable='yes|no' timeout='X'/>
</os>
Where X represents some positive integer representing
milliseconds.
Any value set for loadparm will override all boot menu options.
If loadparm=PROMPT, then the menu will be enabled without a
timeout.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The s390-ccw firmware needs some information in support of the
boot process which is not available on the native machine.
Examples are the netboot firmware load address and now the
boot menu parameters.
While storing that data in unused fields of the IPL parameter block
works, that approach could create problems if the parameter block
definition should change in the future. Because then a guest could
overwrite these fields using the set IPLB diagnose.
In fact the data in question is of more global nature and not really
tied to an IPL device, so separating it is rather logical.
This commit introduces a new structure to hold firmware relevant
IPL parameters set by QEMU. The data is stored at location 204 (dec)
and can contain up to 7 32-bit words. This area is available to
programming in the z/Architecture Principles of Operation and
can thus safely be used by the firmware until the IPL has completed.
Signed-off-by: Viktor Mihajlovski <mihajlov@linux.vnet.ibm.com>
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
[thuth: fixed "4 + 8 * n" comment]
Signed-off-by: Thomas Huth <thuth@redhat.com>
-----BEGIN PGP SIGNATURE-----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=DMbf
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-misc-2018-02-07-v4' into staging
Miscellaneous patches for 2018-02-07
# gpg: Signature made Fri 09 Feb 2018 12:52:51 GMT
# gpg: using RSA key 3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-misc-2018-02-07-v4:
Move include qemu/option.h from qemu-common.h to actual users
Drop superfluous includes of qapi/qmp/qjson.h
Drop superfluous includes of qapi/qmp/dispatch.h
Include qapi/qmp/qnull.h exactly where needed
Include qapi/qmp/qnum.h exactly where needed
Include qapi/qmp/qbool.h exactly where needed
Include qapi/qmp/qstring.h exactly where needed
Include qapi/qmp/qdict.h exactly where needed
Include qapi/qmp/qlist.h exactly where needed
Include qapi/qmp/qobject.h exactly where needed
qdict qlist: Make most helper macros functions
Eliminate qapi/qmp/types.h
Typedef the subtypes of QObject in qemu/typedefs.h, too
Include qmp-commands.h exactly where needed
Drop superfluous includes of qapi/qmp/qerror.h
Include qapi/error.h exactly where needed
Drop superfluous includes of qapi-types.h and test-qapi-types.h
Clean up includes
Use #include "..." for our own headers, <...> for others
vnc: use stubs for CONFIG_VNC=n dummy functions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
qemu-common.h includes qemu/option.h, but most places that include the
former don't actually need the latter. Drop the include, and add it
to the places that actually need it.
While there, drop superfluous includes of both headers, and
separate #include from file comment with a blank line.
This cleanup makes the number of objects depending on qemu/option.h
drop from 4545 (out of 4743) to 284 in my "build everything" tree.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-20-armbru@redhat.com>
[Semantic conflict with commit bdd6a90a9e in block/nvme.c resolved]
This cleanup makes the number of objects depending on qapi/qmp/qdict.h
drop from 4550 (out of 4743) to 368 in my "build everything" tree.
For qapi/qmp/qobject.h, the number drops from 4552 to 390.
While there, separate #include from file comment with a blank line.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-13-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-6-armbru@redhat.com>
This cleanup makes the number of objects depending on qapi/error.h
drop from 1910 (out of 4743) to 1612 in my "build everything" tree.
While there, separate #include from file comment with a blank line,
and drop a useless comment on why qemu/osdep.h is included first.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-5-armbru@redhat.com>
[Semantic conflict with commit 34e304e975 resolved, OSX breakage fixed]
When registering ioat, pba should be comprised of leftmost 52 bits and
rightmost 12 binary zeros, and pal should be comprised of leftmost 52
bits and right most 12 binary ones. The lower 12 bits of words 5 and 7
of the FIB are ignored by the facility. Let's fixup this.
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Message-Id: <20180205072258.5968-4-zyimin@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The VFIO common code doesn't provide the possibility to modify a
previous mapping entry in another way than unmapping and mapping again
with new properties.
To avoid -EEXIST DMA mapping error, we introduce a GHashTable to store
S390IOTLBEntry instances in order to cache the mapped entries. When
intercepting rpcit instruction, ignore the identical mapped entries to
avoid doing map operations multiple times and do unmap and re-map
operations for the case of updating the valid entries.
Acked-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Message-Id: <20180205072258.5968-3-zyimin@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Current s390x PCI IOMMU code is lack of flags' checking, including:
1) protection bit
2) table length
3) table offset
4) intermediate tables' invalid bit
5) format control bit
This patch introduces a new struct named S390IOTLBEntry, and makes up
these missed checkings. At the same time, inform the guest with the
corresponding error number when the check fails. Finally, in order to
get the error number, we export s390_guest_io_table_walk().
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Message-Id: <20180205072258.5968-2-zyimin@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This avoids tons of conversions when handling interrupts.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180129125623.21729-19-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We should be pretty good in shape now. Floating interrupts are working
and atomic instructions should be atomic.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180129125623.21729-15-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
System headers should be included with <...>, our own headers with
"...". Offenders tracked down with an ugly, brittle and probably
buggy Perl script. Previous iteration was commit a9c94277f0.
Delete inclusions of "string.h" and "strings.h" instead of fixing them
to <string.h> and <strings.h>, because we always include these via
osdep.h.
Put the cleaned up system header includes first.
While there, separate #include from file comment with exactly one
blank line.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-2-armbru@redhat.com>
Fix storage attribute migration so that it does not fail for guests
with more than a few GB of RAM.
With such guests, the index in the buffer would go out of bounds,
usually by large amounts, thus receiving -EFAULT from the kernel.
Migration itself would be successful, but storage attributes would then
not be migrated completely.
This patch fixes the out of bounds access, and thus migration of all
storage attributes when the guest have large amounts of memory.
Cc: qemu-stable@nongnu.org
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Fixes: 903fd80b03 ("s390x/migration: Storage attributes device")
Message-Id: <1516297904-18188-1-git-send-email-imbrenda@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
One fprintf(stderr, was manually converted to a
qemu_log_mask(LOG_GUEST_ERROR,
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <3f49c0ff601f27534d4536c87c00d01c233e067f.1513790495.git.alistair.francis@xilinx.com>
[CH: tweaked commit message]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Linux crashes right now if maxmem > mem is specified on the command line.
On s390x, the guest can hotplug memory itself right now - very weird -
and e.g. Fedora 27 will simply add all memory it can when booting.
So now, we have at least the same behavior on TCG and KVM.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20171218224616.21030-3-david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The highest cpu address is not the same as max_cpus. max_cpus
counts from 1 while the cpu address starts at 0.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Message-Id: <20171219082807.84494-1-borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Remove dependency of possible_cpus on 1st CPU instance,
which decouples configuration data from CPU instances that
are created using that data.
Also later it would be used for enabling early cpu to numa node
configuration at runtime qmp_query_hotpluggable_cpus() should
provide a list of available cpu slots at early stage,
before machine_init() is called and the 1st cpu is created,
so that mgmt might be able to call it and use output to set
numa mapping.
Use MachineClass::possible_cpu_arch_ids() callback to set
cpu type info, along with the rest of possible cpu properties,
to let machine define which cpu type* will be used.
* for SPAPR it will be a spapr core type and for ARM/s390x/x86
a respective descendant of CPUClass.
Move parse_numa_opts() in vl.c after cpu_model is parsed into
cpu_type so that possible_cpu_arch_ids() would know which
cpu_type to use during layout initialization.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <1515597770-268979-1-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
exec: housekeeping (funny since 02d0e09503)
applied using ./scripts/clean-includes
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Thanks to Laszlo Ersek for spotting the double semicolon in target/i386/kvm.c
I have trivially grepped the tree for ';;' in C files.
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
KVM does not allow memory regions > KVM_MEM_MAX_NR_PAGES, basically
limiting the memory per slot to 8TB-4k. As memory slots on s390/kvm must
be a multiple of 1MB we need start a new memory region if we cross
8TB-1M.
With that (and optimistic overcommitment in the kernel) I was able to
start a 24TB guest on a 1TB system.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20171211122146.162430-1-borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
[CH: 1UL -> 1ULL in KVM_MEM_MAX_NR_PAGES; build fix on 32 bit hosts]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We are good enough to boot upstream Linux kernels / Fedora 26/27. That
should be sufficient for now.
As the QEMU CPU model is migration safe, let's add compatibility code.
Generate the feature list to reduce the chance of messing things up in the
future.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20171208165529.14124-1-david@redhat.com>
[CH: squashed 's390x/cpumodel: make qemu cpu model play with "none" machine'
(20171213132407.5227-1-david@redhat.com) and 's390x/tcg: don't include z13
features in the qemu model' (20171213171512.17601-1-david@redhat.com) into
patch]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Logically, the css bridge should be attached to the machine.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Tested-by: Bjoern Walk <bwalk@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
With the cssids unrestricted (commit "s390x/css: unrestrict cssids") the
s390-squash-mcss machine property should not be used. Actually Libvirt
never supported this, so the expectation is that removing it should be
pretty painless. But let's play nice and deprecate it first.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20171206144438.28908-3-pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The default css 0xfe is currently restricted to virtual subchannel
devices. The hope when the decision was made was, that non-virtual
subchannel devices will come around when guest can exploit multiple
channel subsystems. Since the guests generally don't do, the pain
of the partitioned (cssid) namespace outweighs the gain.
Let us remove the corresponding restrictions (virtual devices
can be put only in 0xfe and non-virtual devices in any css except
the 0xfe -- while s390-squash-mcss then remaps everything to cssid 0).
At the same time, change our schema for generating css bus ids to put
both virtual and non-virtual devices into the default css (spilling over
into other css images, if needed). The intention is to deprecate
s390-squash-mcss. With this change devices without a specified devno
won't end up hidden to guests not supporting multiple channel subsystems,
unless this can not be avoided (default css full).
Let us also advertise the changes to the management software (so it can
tell are cssids unrestricted or restricted).
The adverse effect of getting rid of the restriction on migration should
not be too severe. Vfio-ccw devices are not live-migratable yet, and for
virtual devices using the extra freedom would only make sense with the
aforementioned guest support in place.
The auto-generated bus ids are affected by both changes. We hope to not
encounter any auto-generated bus ids in production as Libvirt is always
explicit about the bus id. Since 8ed179c937 ("s390x/css: catch section
mismatch on load", 2017-05-18) the worst that can happen because the same
device ended up having a different bus id is a cleanly failed migration.
I find it hard to reason about the impact of changed auto-generated bus
ids on migration for command line users as I don't know which rules is
such an user supposed to follow.
Another pain-point is down- or upgrade of QEMU for command line users.
The old way and the new way of doing vfio-ccw are mutually incompatible.
Libvirt is only going to support the new way, so for libvirt users, the
possible problems at QEMU downgrade are the following. If a domain
contains virtual devices placed into a css different than 0xfe the domain
will refuse to start with a QEMU not having this patch. Putting devices
into a css different that 0xfe however won't make much sense in the near
future (guest support). Libvirt will refuse to do vfio-ccw with a QEMU
not having this patch. This is business as usual.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Message-Id: <20171206144438.28908-2-pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
When dispatching memory access to PCI BAR region, we must
look for possible subregions, used by the PCI device to map
different memory areas inside the same PCI BAR.
Since the data offset we received is calculated starting at the
region start address we need to adjust the offset for the subregion.
The data offset inside the subregion is calculated by substracting
the subregion's starting address from the data offset in the region.
The access to the MSIX region is now handled in a generic way,
we do not need the specific trap_msix() function anymore.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Message-Id: <1512046530-17773-8-git-send-email-pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's move the memory region write from pcistg into a dedicated
function.
This allows us to prepare a later patch searching for subregions
inside of the memory region.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1512046530-17773-7-git-send-email-pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's move the memory region read from pcilg into a dedicated function.
This allows us to prepare a later patch.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1512046530-17773-6-git-send-email-pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Enhance the fault detection.
Fixup the precedence to check the destination path existance
before checking for the source accessibility.
Add the maxstbl entry to both the Query PCI Function Group
response and the PCIBusDevice structure.
Initialize the maxstbl to 128 per default until we get
the actual data from the hardware.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Message-Id: <1512046530-17773-5-git-send-email-pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Enhance the fault detection, correction of the fault reporting.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Message-Id: <1512046530-17773-4-git-send-email-pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Enhance the fault detection, correction of the fault reporting.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Message-Id: <1512046530-17773-3-git-send-email-pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
There are two places where the same endianness conversion
is done.
Let's factor this out into a static function.
Note that the conversion must always be done for data in a register:
The S390 BE guest converted date to le before issuing the instruction.
After interception in a BE host:
ZPCI VFIO using pwrite must make the conversion back for the BE kernel.
Kernel will do BE to le translation when loading the register for the
real instruction.
After interception in a le host:
TCG stores a BE register in le, swapping bytes.
But since the data in the register was already le it is now BE
ZPCI VFIO must convert it to le before writing to the PCI memory.
In both cases ZPCI VFIO must swap the bytes from the register.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Message-Id: <1512046530-17773-2-git-send-email-pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
s390_cpu_virt_mem_rw() must always return, so callers can react on
an exception (e.g. see ioinst_handle_stcrw()).
However, for TCG we always have to exit the cpu loop (and restore the
cpu state before that) if we injected a program interrupt. So let's
introduce and use s390_cpu_virt_mem_handle_exc() in code that is not
purely KVM.
Directly pass the retaddr we already have available in these functions.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20171130162744.25442-8-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Once we wire up TCG, we will need the retaddr to correctly inject
program interrupts. As we want to get rid of the function
program_interrupt(), convert PCI code too.
For KVM, we can simply use RA_IGNORED.
Convert program_interrupt() to s390_program_interrupt() directly, making
use of the passed address.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20171130162744.25442-6-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
It is broken and not even wired up. We'll add a new handler soon, but
that will live somewhere else.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20171130162744.25442-4-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The bus pointer in PCIDevice is basically redundant with QOM information.
It's always initialized to the qdev_get_parent_bus(), the only difference
is the type.
Therefore this patch eliminates the field, instead creating a pci_get_bus()
helper to do the type mangling to derive it conveniently from the QOM
Device object underneath.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
A fair proportion of the users of pci_bus_num() want to get the bus
number on a specific device, so first have to look up the bus from the
device then call it. This adds a helper to do that (since we're going
to make looking up the bus slightly more verbose).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
pci_bus_init(), pci_bus_new_inplace(), pci_bus_new() and pci_register_bus()
are misleadingly named. They're not used for initializing *any* PCI bus,
but only for a root PCI bus.
Non-root buses - i.e. ones under a logical PCI to PCI bridge - are instead
created with a direct qbus_create_inplace() (see pci_bridge_initfn()).
This patch renames the functions to make it clear they're only used for
a root bus.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
We no longer support the old s390 transport, neither does the newest
Linux kernel. Remove it from the linux header script as well as the
s390x virtio code. We still should handle the VIRTIO_NOTIFY hypercall,
to tolerate early printk on older guest kernels without an sclp console.
We continue to ignore these events.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20171115154223.109991-1-borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Currently, to enable a pci device in the guest, the user has to issue
echo 1 > /sys/bus/pci/slots/00000000/power. This is not what people
expect. On an LPAR, the user can put a PCI device in configured or
deconfigured state via IOCDS. The "start in deconfigured state" can be
used for "sharing" a pci function across LPARs. This is not what we are
going to use in KVM, so always start configured.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Message-Id: <20171107175455.73793-2-borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Starting a guest with
<os>
<type arch='s390x' machine='s390-ccw-virtio-2.9'>hvm</type>
</os>
<cpu mode='host-model'/>
on an IBM z14 results in
"qemu-system-s390x: Some features requested in the CPU model are not
available in the configuration: gs"
This is because guarded storage is fenced for compat machines that did
not have guarded storage support. While this prevents future migration
abort (by not starting the guest at all), not being able to start a
"host-model" guest is very much unexpected. As it turns out, even if we
would modify libvirt to not expand the cpu model to contain "gs" for
compat machines, it cannot guarantee that a migration will succeed. For
example if the kernel changes its features (or the user has nested=1 on
one host but not on the other) the migration will fail nevertheless. So
instead of fencing "gs" for machines <= 2.9 lets allow it for all
machine types that support the CPU model. This will make "host-model"
runnable all the time, while relying on the CPU model to reject invalid
migration attempts. We also need to change the migration for guarded
storage.
Additional discussions about host-model are still pending but are out
of scope of this patch.
Suggested-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Cornelia Huck <Cornelia Huck <cohuck@redhat.com>
Acked-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Simplify the error handling of the MSCH. Let the code detecting the
condition tell (in a less ambiguous way) how it's to be handled. No
changes in behavior.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20171017140453.51099-8-pasic@linux.vnet.ibm.com>
[CH: fix return code for fctl != 0]
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Simplify the error handling of the HSCH. Let the code detecting the
condition tell (in a less ambiguous way) how it's to be handled. No
changes in behavior.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20171017140453.51099-7-pasic@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Simplify the error handling of the CSCH. Let the code detecting the
condition tell (in a less ambiguous way) how it's to be handled. No
changes in behavior.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20171017140453.51099-6-pasic@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Simplify the error handling of the XSCH. Let the code detecting the
condition tell (in a less ambiguous way) how it's to be handled. No
changes in behavior.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20171017140453.51099-5-pasic@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Simplify the error handling of the SSCH and RSCH handler avoiding
arbitrary and cryptic error codes being used to tell how the instruction
is supposed to end. Let the code detecting the condition tell how it's
to be handled in a less ambiguous way. It's best to handle SSCH and RSCH
in one go as the emulation of the two shares a lot of code.
For passthrough this change isn't pure refactoring, but changes the way
kernel reported EFAULT is handled. After clarifying the kernel interface
we decided that EFAULT shall be mapped to unit exception. Same goes for
unexpected error codes and absence of required ORB flags.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20171017140453.51099-4-pasic@linux.vnet.ibm.com>
Tested-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
[CH: cosmetic changes]
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
s390-virtio-ccw.c is the sole user of s390x_new_cpu(),
so move this helper there.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1508253203-119237-1-git-send-email-imammedo@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The architecture supports masks of variable length for sclp write
event mask. We currently only support 4 byte event masks, as that
is what Linux uses.
Let's extend this to the maximum mask length supported by the
architecture and return 0 to the guest for the mask bits we don't
support in core.
Initial patch by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Message-Id: <1507729193-9747-1-git-send-email-jjherne@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Wire up the virtio-input HID devices (keyboard, mouse, tablet)
for the CCW bus. The virtio-input is a virtio-1 device,
so disable legacy revision 0.
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <6a8ea4c503ee32c2ca7fa608b5f2f547009be8ee.1507557166.git.alifm@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Nothing hindering us anymore from unlocking the restart code (used for
NMI).
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-29-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This effectively enables experimental SMP support. Floating interrupts are
still a mess, so allow it but print a big warning. There also seems
to be a problem with CPU hotplug (after the main loop started).
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-27-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[CH: changed insn-data.def as pointed out by Richard]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We want to use the same code base for TCG, so let's cleanly factor it
out.
The sigp mutex is currently not really needed, as everything is
protected by the iothread mutex. But this could change later, so leave
it in place and initialize it properly from common code.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-17-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Calling do_subchannel_work with no function control flags set in SCSW is
a programming error. Currently we handle this differently in
do_subchannel_work_virtual and do_subchannel_work_passthrough. Let's be
consistent and guard with a common assert against this programming error.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20171004154144.88995-2-pasic@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The "sclpquiesce" device is just an internal device that should not be
created by the user directly. Though it currently does not seem to cause
any obvious trouble when the user instantiates an additional device, let's
better mark it with user_creatable = false to avoid unexpected behavior,
e.g. because the quiesce notifier gets registered multiple times.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1507193105-15627-1-git-send-email-thuth@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
A TYPE_SCLP_CPU_HOTPLUG device for handling cpu hotplug events
is already created by the sclp event facility. Adding a second
TYPE_SCLP_CPU_HOTPLUG device via -device sclp-cpu-hotplug creates
an ambiguity in raise_irq_cpu_hotplug(), leading to a crash once
a cpu is hotplugged.
To fix this, disallow creating a sclp-cpu-hotplug device manually.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The "sclp" device is just an internal device that can not be instantiated
by the users. If they try to use it, they only get a simple error message:
$ qemu-system-s390x -nographic -device sclp
qemu-system-s390x: Option '-device s390-sclp-event-facility' cannot be
handled by this machine
Since sclp_init() tries to create a TYPE_SCLP_EVENT_FACILITY which is
a non-pluggable sysbus device, there is really no way that the "sclp"
device can be used by the user, so let's set the user_creatable = false
accordingly.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1507125199-22562-1-git-send-email-thuth@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Reviewed-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Acked-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
If we fail to set a proper TOD clock on the target system, this can
already result in some problematic cases. We print several warn messages
on source and target in that case.
If kvm fails to set a nonzero epoch index, then we must ultimately fail
the migration as this will result in a giant time leap backwards. This
patch lets the migration fail if we can not set the guest time on the
target.
On failure the guest will resume normally on the original host machine.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
[split failure change from epoch index change, minor fixups]
Message-Id: <20171004105751.24655-3-borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Commit e996583eb3 ("s390x/css: activate ChannelSubSys migration",
2017-07-11) was supposed to enable css migration for virtio-ccw
machines starting 2.10, but it ended up effectively enabling it
only for 2.10 as the registration of the appropriate VMStateDescription
happens in ccw_machine_2_10_instance_options which does not get
called for machines more recent than 2_10.
Let us move the corresponding chunk of code (which conditionally enables
the migration based on the value of the corresponding class property) to
ccw_init, which is called for each virtio-ccw machine instance.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reported-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20171004110109.16525-1-pasic@linux.vnet.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Will be handy in the future.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928134609.16985-6-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's move it into the machine, so we trigger the IRQ after setting
ms->possible_cpus (which SCLP uses to construct the list of
online CPUs).
This also fixes a problem reported by Thomas Huth, whereby qemu can be
crashed using the none machine
qemu-s390x-softmmu -M none -monitor stdio
-> device_add qemu-s390-cpu
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928134609.16985-3-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let us convert the 3270 code so it uses the recently introduced
CcwDataStream abstraction instead of blindly assuming direct data access.
This patch does not change behavior beyond introducing IDA support: for
direct data access CCWs everything stays as-is. (If there are bugs, they
are also preserved).
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Message-Id: <20170920172314.102710-2-pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This reverts commit d32bd032d8.
Turns out that old QEMUs always created a pci host bridge
and for many CPU models the migration from old QEMUs to new
QEMUs will fail with
qemu-system-s390x: Unknown savevm section or instance 'PCIBUS' 0
qemu-system-s390x: load of migration failed: Invalid argument
As a quick fix we will revert the commit and always create the
pci host bridge.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
[fixed revert to keep the comment fixup, added a comment in the code]
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: David Hildenbrand <david@redhat.com>
Message-Id: <20170928131831.81393-1-borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's add indirect data addressing support for our virtual channel
subsystem. This implementation does not bother with any kind of
prefetching. We simply step through the IDAL on demand.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20170921180841.24490-6-pasic@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The architecture mandates the addresses to be accessed on the first
indirection level (that is, the data addresses without IDA, and the
(M)IDAW addresses with (M)IDA) to be checked against an CCW format
dependent limit maximum address. If a violation is detected, the storage
access is not to be performed and a channel program check needs to be
generated. As of today, we fail to do this check.
Let us stick even closer to the architecture specification.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20170921180841.24490-5-pasic@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Replace direct access which implicitly assumes no IDA
or MIDA with the new ccw data stream interface which should
cope with these transparently in the future.
Note that checking the return code for ccw_dstream_* will be
done in a follow-on patch.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Message-Id: <20170921180841.24490-4-pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Replace direct access which implicitly assumes no IDA
or MIDA with the new ccw data stream interface which should
cope with these transparently in the future.
Note that checking the return code for ccw_dstream_* will be
done in a follow-on patch.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Message-Id: <20170921180841.24490-3-pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This is a preparation for introducing handling for indirect data
addressing and modified indirect data addressing (CCW). Here we introduce
an interface which should make the addressing scheme transparent for the
client code. Here we implement only the basic scheme (no IDA or MIDA).
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Message-Id: <20170921180841.24490-2-pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Define default CPU type in generic way in machine class_init
and let common machine code handle cpu_model parsing.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <1505998749-269631-1-git-send-email-imammedo@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Modify the pre_save method on VMStateDescription to return an int
rather than void so that it potentially can fail.
Changed zillions of devices to make them return 0; the only
case I've made it return non-0 is hw/intc/s390_flic_kvm.c that already
had an error_report/return case.
Note: If you add an error exit in your pre_save you must emit
an error_report to say why.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170925112917.21340-2-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Wire up the virtio-gpu device for the CCW bus. The virtio-gpu
is a virtio-1 device, so disable revision 0.
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <6c53f939cf2d64b66d2a6878b29c9bf3820f3d5b.1505485574.git.alifm@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We have two stale comments suggesting one should think about virtio
config space endianness a bit longer. We have just done that, and came to
the conclusion we are fine as is: it's the responsibility of the virtio
device and not of the transport (and that is how it works now). Putting
the responsibility into the transport isn't even possible, because the
transport would have to know about the config space layout of each
device.
Let us remove the stale comments.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Suggested-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20170914105535.47941-1-pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This is the first step to allow hot plugging of CPUs in a non-sequential
order. If a cpu is available ("plugged") can directly be decided by
looking at the cpu state pointer.
This makes sure, that really only cpus attached to the machine are
reported.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170913132417.24384-22-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Now that there is only one user of cpu_s390x_create() left, make cpu
creation look like on x86.
- Perform the model/properties split and checks in s390_init_cpus()
- Parse features only once without having to remember if already parsed
- Pass only the typename to s390x_new_cpu()
- Use the typename of an existing CPU for hotplug via cpu-add
Acked-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170913132417.24384-21-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Now that we have possible_cpus, we can get rid of the global variable
and rewrite s390_cpu_addr2state() to use it.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170913132417.24384-20-david@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
CPU hotplug is only possible on a per core basis on s390x. So let's
add possible_cpus and wire everything up properly.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170913132417.24384-19-david@redhat.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
device_del on a CPU will currently do nothing. Let's emit an error
telling that this is will currently not work (there is no architecture
support on s390x). Error message copied from ppc.
(qemu) device_del cpu1
device_del cpu1
CPU hot unplug not supported on this machine
Reviewed-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170913132417.24384-18-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Some time ago we discussed that using "id" as property name is not the
right thing to do, as it is a reserved property for other devices and
will not work with device_add.
Switch to the term "core-id" instead, and use it as an equivalent to
"CPU address" mentioned in the PoP. There is no such thing as cpu number,
so rename env.cpu_num to env.core_id. We use "core-id" as this is the
common term to use for device_add later on (x86 and ppc).
We can get rid of cpu->id now. Keep cpu_index and env->core_id in sync.
cpu_index was already implicitly used by e.g. cpu_exists(), so keeping
both in sync seems to be the right thing to do.
cpu_index will now no longer automatically get set via
cpu_exec_realizefn(). For now, we were lucky that both implicitly stayed
in sync.
Our new cpu property "core-id" can be a static property. Range checks can
be avoided by using the correct type and the "setting after realized"
check is done implicitly.
device_add will later need the reserved "id" property. Hotplugging a CPU
on s390x will then be: "device_add host-s390-cpu,id=cpu2,core-id=2".
Reviewed-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170913132417.24384-14-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Specifying more than 1 CPU (e.g. -smp 5) leads to SIGP errors (the
guest tries to bring these CPUs up but fails), because we don't support
multiple CPUs on s390x under TCG.
Let's bail out if more than 1 is specified, so we don't raise people's
hope.
Tested-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170913132417.24384-12-david@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Implemented in hw/s390x/s390-virtio-hcall.c, so let's move it to the
right header file.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170913132417.24384-6-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The only interface left, so let's properly rename it.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170913132417.24384-5-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
It is a leftover from the days where we had still the !ccw virtio
machine. As this one is long gone, let's move everything to
s390-virtio-ccw.c.
Suggested-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170913132417.24384-4-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The case in question actually never happens. Let us get rid of the dead
code.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20170908152446.14606-4-pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Back then in the time of df1fe5bb49 ("s390: Virtual channel subsystem
support.", 2013-01-24) -EIO used to map to a channel-program check (via
the default label of the switch statement). Then 2dc95b4cac
("s390x/3270: 3270 data stream handling", 2016-04-01) came along
and that changed dramatically.
Let us roll back this undesired side effect, and go back to
channel-program check.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Fixes: 2dc95b4cac "s390x/3270: 3270 data stream handling"
Message-Id: <20170908152446.14606-3-pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The architecture says that channel-data check is indicating that
an uncorrected storage (memory) error has been detected in regard
to the data residing in main storage (memory) that is currently
used for an I/O operation. The described detection is done using
the CBC technology.
The ccw interpretation code is however generating a channel-data check
effectively when the (device specific) ccw_cb returns -EFAULT. In case
of virtio-ccw devices this happens when mapping memory fails, or when a
NULL pointer is encountered. So this behavior is not architecture
conform.
Furthermore the best fit for these situations (null pointer, mapping a
piece of guest memory fails) from architectural perspective the condition
described as the channel subsystem refers to a location that is not
available, which when encountered shall result in a channel-program
check.
To fix this, all we have to do is to get rid of the switch case matching
-EFAULT: the default is generating a channel-program check.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20170908152446.14606-2-pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's introduce iommu replay callback for s390 pci iommu memory region.
Currently we don't need any dma mapping replay. So let it return
directly. This implementation will avoid meaningless loops calling
translation callback.
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Message-Id: <1504606380-49341-4-git-send-email-zyimin@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
PCIDevice pointer has been a parameter of kvm_arch_fixup_msi_route().
So we don't need to store zpci idx in msix message data to find out the
specific zpci device. Instead, we could use pci device id to find its
corresponding zpci device.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Message-Id: <1504606380-49341-2-git-send-email-zyimin@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The function ioinst_handle_xsch is presenting cc 2 when it's supposed to
present cc 1 and the other way around, because css_do_xsch has the error
codes mixed up. Because cc 1 has precedence over cc 2 we also have to
swap the two checks.
Let us fix this.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reported-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Message-Id: <20170831121828.85885-1-pasic@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Tidy up some of the warn_report() messages after having converted them
to use warn_report().
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <9cb1d23551898c9c9a5f84da6773e99871285120.1505158760.git.alistair.francis@xilinx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert all the multi-line uses of fprintf(stderr, "warning:"..."\n"...
to use warn_report() instead. This helps standardise on a single
method of printing warnings to the user.
All of the warnings were changed using these commands:
find ./* -type f -exec sed -i \
'N; {s|fprintf(.*".*warning[,:] \(.*\)\\n"\(.*\));|warn_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N; {s|fprintf(.*".*warning[,:] \(.*\)\\n"\(.*\));|warn_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N; {s|fprintf(.*".*warning[,:] \(.*\)\\n"\(.*\));|warn_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N {s|fprintf(.*".*warning[,:] \(.*\)\\n"\(.*\));|warn_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N;N {s|fprintf(.*".*warning[,:] \(.*\)\\n"\(.*\));|warn_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N;N;N {s|fprintf(.*".*warning[,:] \(.*\)\\n"\(.*\));|warn_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N;N;N;N; {s|fprintf(.*".*warning[,:] \(.*\)\\n"\(.*\));|warn_report("\1"\2);|Ig}' \
{} +
Indentation fixed up manually afterwards.
Some of the lines were manually edited to reduce the line length to below
80 charecters. Some of the lines with newlines in the middle of the
string were also manually edit to avoid checkpatch errrors.
The #include lines were manually updated to allow the code to compile.
Several of the warning messages can be improved after this patch, to
keep this patch mechanical this has been moved into a later patch.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Yongbok Kim <yongbok.kim@imgtec.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Jason Wang <jasowang@redhat.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <5def63849ca8f551630c6f2b45bcb1c482f765a6.1505158760.git.alistair.francis@xilinx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The function trap_msix() is to check if pcistg instruction would access
msix table entries. The correct boundary condition should be
[table_offset, table_offset+entries*entry_size). But the current
condition calculated misses the last entry. So let's fixup it.
Acked-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Message-Id: <1503907487-2764-2-git-send-email-zyimin@linux.vnet.ibm.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The storage attribute devices are only meant to be instantiated one
time, internally. They can not be used by the user, so mark them with
user_creatable = false.
Suggested-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1503576029-24264-1-git-send-email-thuth@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's do it just like the other architectures. Introduce kvm-stub.c
for stubs and kvm_s390x.h for the declarations.
Change license to GPL2+ and keep copyright notice.
As we are dropping the sysemu/kvm.h include from cpu.h, fix up includes.
Suggested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170818114353.13455-18-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's just introduce an helper.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170818114353.13455-17-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The functions are not used in target/s390x/ so a header in hw/s390x/
is a better place.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170818114353.13455-9-david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
s390-stattrib.c needs definition of TARGET_PAGE_SIZE, solve it via cpu.h.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170818114353.13455-8-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Now we can drop inclusion of "sysemu/kvm.h" from "s390-virtio.c".
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170818114353.13455-7-david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's avoid any KVM stuff in s390-virtio-ccw.c. This parameter is simply
ignored.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170818114353.13455-6-david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
No need for kvm_enabled() as this function is only called from KVM and
there is no reason why it shouldn't be allowed for tcg. It is simply not
available under tcg.
Also, there is no need to check for the machine type anymore. Just like
ri_enabled(), we can directly use the stored flag, which results in
"true" for the "none" machine.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170818114353.13455-5-david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Only used in KVM and there is no reason why it shouldn't be allowed for
tcg - it is simply not available.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170818114353.13455-4-david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Not needed at that point.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170818114353.13455-2-david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
QEMU currently aborts if the user tries to create a skey device:
$ s390x-softmmu/qemu-system-s390x -nographic -device s390-skeys-qemu
qemu-system-s390x: hw/s390x/s390-skeys.c:30: s390_get_skeys_device:
Assertion `ss' failed.
Aborted (core dumped)
The storage key devices are only meant to be instantiated one time,
internally. They can not be used by the user, so mark them with
user_creatable = false.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1503569328-22197-1-git-send-email-thuth@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
If we do not provide zpci, pci reconfiguration via sclp is not available
either. I/O adapter configuration, however, should always be present.
Rename the values that refer to I/O adapter configuration (instead of only
pci) to make things clearer.
Move length checking of the sccb for I/O adapter configuration into the
common sclp code (out of the pci code). This also fixes an issue that
the pci code would refer to a field in the sccb before checking whether
it was actually long enough.
Check for the adapter type in the sccb and return unrecognized adapter
type if the guest tries to issue I/O adapter configure/deconfigure for
a type other than pci or for pci if the zpci facility is not provided.
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Don't create the s390 pci host bridge if we do not provide the zpci
facility.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The nt2 event class is pci-only - don't look for events if pci is
not in the active cpu model.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Some non-pci code calls into zpci code. Provide some stubs for builds
without pci.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The s390-ipl device can not be created by the user, since it is meant only
to be instantiated once internally to load the ROMs and kernel. If the user
tries to do a "device_add s390-ipl" via the monitor later, QEMU aborts with
a "ROM images must be loaded at startup" error message.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1502861458-30270-1-git-send-email-thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
A successful completion of rchp should signal a solicited channel path
initialized CRW (channel report word), while the current implementation
always generates an un-solicited one. Let's fix this.
Reported-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20170803003527.86979-3-bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's use a macro for the ERC (error recover code) when generating a
Channel Subsystem Event-information pending CRW (channel report word).
While we are at it, let's also add all other ERCs.
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20170803003527.86979-2-bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The only exception are groups of numers separated by symbols
'.', ' ', ':', '/', like 'ab.09.7d'.
This patch is made by the following:
> find . -name trace-events | xargs python script.py
where script.py is the following python script:
=========================
#!/usr/bin/env python
import sys
import re
import fileinput
rhex = '%[-+ *.0-9]*(?:[hljztL]|ll|hh)?(?:x|X|"\s*PRI[xX][^"]*"?)'
rgroup = re.compile('((?:' + rhex + '[.:/ ])+' + rhex + ')')
rbad = re.compile('(?<!0x)' + rhex)
files = sys.argv[1:]
for fname in files:
for line in fileinput.input(fname, inplace=True):
arr = re.split(rgroup, line)
for i in range(0, len(arr), 2):
arr[i] = re.sub(rbad, '0x\g<0>', arr[i])
sys.stdout.write(''.join(arr))
=========================
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-id: 20170731160135.12101-5-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
With the move of some docs/ to docs/devel/ on ac06724a71,
no references were updated.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
According to the PoP bit positions 0-3 and 8-32 of the format-1 CCW must
contain zeros. Bits 0-3 are already covered by cmd_code validity
checking, and bit 32 is covered by the CCW address checking.
Bits 8-31 correspond to CCW1.flags and CCW1.count. Currently we only
check for the absence of certain flags. Let's fix this.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20170725224442.13383-3-pasic@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
[CH: tweaked comment]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
According to the PoP channel command words (CCW) must be doubleword
aligned and 31 bit addressable for format 1 and 24 bit addressable for
format 0 CCWs.
If the channel subsystem encounters a ccw address which does not satisfy
this alignment requirement a program-check condition is recognised.
The situation with 31 bit addressable is a bit more complicated: both the
ORB and a format 1 CCW TIC hold the address of (the rest of) the channel
program, that is the address of the next CCW in a word, and the PoP
mandates that bit 0 of that word shall be zero -- or a program-check
condition is to be recognized -- and does not belong to the field holding
the ccw address.
Since in code the corresponding fields span across the whole word (unlike
in PoP where these are defined as 31 bit wide) we can check this by
applying a mask. The 24 addressable case isn't affecting TIC because the
address is composed of a halfword and a byte portion (no additional zero
bit requirements) and just slightly complicates the ORB case where also
bits 1-7 need to be zero.
The same requirements (especially n-bit addressability) apply to the
ccw addresses generated while chaining.
Let's make our CSS implementation follow the AR more closely.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20170727154842.23427-1-pasic@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
On NetBSD, where tolower() and toupper() are implemented using an
array lookup, the compiler warns if you pass a plain 'char'
to these functions:
gdbstub.c:914:13: warning: array subscript has type 'char'
This reflects the fact that toupper() and tolower() give
undefined behaviour if they are passed a value that isn't
a valid 'unsigned char' or EOF.
We have qemu_tolower() and qemu_toupper() to avoid this problem;
use them.
(The use in scsi-generic.c does not trigger the warning because
it passes a uint8_t; we switch it anyway, for consistency.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com> for the s390 part.
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-id: 1500568290-7966-1-git-send-email-peter.maydell@linaro.org
Use the new functions memory_region_init_{ram,rom,rom_device}()
instead of manually calling the _nomigrate() version and then
vmstate_register_ram_global().
Patch automatically created using coccinelle script:
spatch --in-place -sp_file scripts/coccinelle/memory-region-init-ram.cocci -dir hw
(As it turns out, there are no instances of the rom and
rom_device functions that are caught by this script.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1499438577-7674-8-git-send-email-peter.maydell@linaro.org
Rename memory_region_init_ram() to memory_region_init_ram_nomigrate().
This leaves the way clear for us to provide a memory_region_init_ram()
which does handle migration.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1499438577-7674-4-git-send-email-peter.maydell@linaro.org
- add a network boot rom for s390 (Thomas Huth)
- migration of storage attributes like the CMMA used/unused state
- PCI related enhancements - full support for aen, ais and zpci
- migration support for css with vmstates (Halil Pasic)
- cpu model enhancements for cpu features
- guarded storage support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=2bOV
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/borntraeger/tags/s390x-20170714' into staging
s390x/kvm/migration/cpumodel: fixes, enhancements and cleanups
- add a network boot rom for s390 (Thomas Huth)
- migration of storage attributes like the CMMA used/unused state
- PCI related enhancements - full support for aen, ais and zpci
- migration support for css with vmstates (Halil Pasic)
- cpu model enhancements for cpu features
- guarded storage support
# gpg: Signature made Fri 14 Jul 2017 11:33:04 BST
# gpg: using RSA key 0x117BBC80B5A61C7C
# gpg: Good signature from "Christian Borntraeger (IBM) <borntraeger@de.ibm.com>"
# Primary key fingerprint: F922 9381 A334 08F9 DBAB FBCA 117B BC80 B5A6 1C7C
* remotes/borntraeger/tags/s390x-20170714: (40 commits)
s390x/gdb: add gs registers
s390x/arch_dump: also dump guarded storage control block
s390x/kvm: enable guarded storage
s390x/kvm: Enable KSS facility for nested virtualization
s390x/cpumodel: add esop/esop2 to z12 model
s390x/cpumodel: we are always in zarchitecture mode
s390x/cpumodel: wire up new hardware features
s390x/flic: migrate ais states
s390x/cpumodel: add zpci, aen and ais facilities
s390x: initialize cpu firstly
pc-bios/s390: rebuild s390-ccw.img
pc-bios/s390: add s390-netboot.img
pc-bios/s390-ccw: Link libnet into the netboot image and do the TFTP load
pc-bios/s390-ccw: Add virtio-net driver code
pc-bios/s390-ccw: Add core files for the network bootloading program
roms/SLOF: Update submodule to latest status
pc-bios/s390-ccw: Add code for virtio feature negotiation
pc-bios/s390-ccw: Remove unused structs from virtio.h
pc-bios/s390-ccw: Move byteswap functions to a separate header
pc-bios/s390-ccw: Add a write() function for stdio
...
Conflicts:
target/s390x/kvm.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce guarded storage support for KVM guests on s390.
We need to enable the capability, extend machine check validity,
sigp store-additional-status-at-address, and migration.
The feature is fenced for older machine type versions.
Signed-off-by: Fan Zhang <zhangfan@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Add esop and esop2 features to z12 model where esop2 was originally
introduced. Disable esop and esop2 when using compatibility machine
v2.9 or earlier.
Signed-off-by: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
zPCI instructions and facilities are available since IBM zEnterprise
EC12. To support z/PCI in QEMU we enable zpci, aen and ais facilities
starting with zEC12 GA1. And we always set zpci and aen bits in max cpu
model. Later they might be switched off due to applied real cpu model.
For ais bit, we only provide it in the full cpu model beginning with
zEC12 and defer its enablement in the default cpu model to a later point
in time. At the same time, disable them for 2.9 and older machines.
Because of introducing AIS facility, we could check if it's enabled to
initialize flic->ais_supported with the real value.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
By initializing the CPU firstly, we are able to retrieve and use the
CPU model features when initializing other subsystem or devices.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Instead of passing around a pointer to ORB let us simplify some
function signatures by using the previously introduced ORB saved at the
subchannel (SubchDev).
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-Id: <20170711145441.33925-7-pasic@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Turn on migration for the channel subsystem for the next machine. For
legacy machines we still have to do things the old way.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-Id: <20170711145441.33925-6-pasic@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Since we are going to need a migration compatibility breaking change to
activate ChannelSubSys migration let us use the opportunity to introduce
ORB to the SubchDev before that (otherwise we would need separate
handling e.g. a compat property).
The ORB will be useful for implementing IDA, or async handling of
subchannel work.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Guenther Hutzl <hutzl@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-Id: <20170711145441.33925-5-pasic@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Although we have recently vmstatified the migration of some css
infrastructure, for some css entities there is still state to be
migrated left, because the focus was keeping migration stream
compatibility (that is basically everything as-is).
Let us add vmstate helpers and extend existing vmstate descriptions so
that we have everything we need. Let us guard the added state via
css_migration_enabled, so we keep the compatible behavior if css
migration is disabled.
Let's also annotate the bits which do not need to be migrated for better
readability.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20170711145441.33925-4-pasic@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Currently the migration of the channel subsystem (css) is only partial
and is done by the virtio ccw proxies -- the only migratable css devices
existing at the moment.
With the current work on emulated and passthrough devices we need to
decouple the migration of the channel subsystem state from virtio ccw,
and have a separate section for it. A new section however necessarily
breaks the migration compatibility.
So let us introduce a switch at the machine class, and put it in 'off'
state for now. We will turn the switch 'on' for future machines once all
preparations are met. For compatibility machines the switch will stay
'off'.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-Id: <20170711145441.33925-3-pasic@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
We will need the machine class at machine initialization time, so the
usual way via qdev won't do. Let's cache the machine class and also use
the default values of the base machine for capability discovery.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-Id: <20170711145441.33925-2-pasic@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Let's use the new inject_airq callback of flic to inject adapter
interrupts. For kvm case, if the kernel flic doesn't support the new
interface, the irq routine remains unchanged. For non-kvm case,
qemu-flic handles the suppression process.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Currently, we do nothing for the SIC instruction, but we need to
implement it properly. Let's add proper handling in the backend code.
Co-authored-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Introduce a new 'flags' field to IoAdapter to contain further
characteristics of the adapter, like whether the adapter is subject to
adapter-interruption suppression.
For the kvm case, pass this value in the 'flags' field when
registering an adapter.
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Add an "info" monitor command to non-destructively inspect the state of
the storage attributes of the guest, and a normal command to toggle
migration mode (useful for debugging).
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Storage attributes device, like we have for storage keys.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Unlike other object_property_add_link() occurrences in virtio devices,
virtio-crypto checks the "in use" state of the linked backend object in
addition to qdev_prop_allow_set_link_before_realize. To convert it
without needing to specialize DEFINE_PROP_LINK which always uses the
qdev callback, move the "in use" check to device realize time.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20170714021509.23681-10-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The remaining non-const ones are in e1000e which modifies description at
runtime. They can be addressed separatedly.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20170714021509.23681-6-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This finishes QOM'fication of IOMMUMemoryRegion by introducing
a IOMMUMemoryRegionClass. This also provides a fastpath analog for
IOMMU_MEMORY_REGION_GET_CLASS().
This makes IOMMUMemoryRegion an abstract class.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20170711035620.4232-3-aik@ozlabs.ru>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This defines new QOM object - IOMMUMemoryRegion - with MemoryRegion
as a parent.
This moves IOMMU-related fields from MR to IOMMU MR. However to avoid
dymanic QOM casting in fast path (address_space_translate, etc),
this adds an @is_iommu boolean flag to MR and provides new helper to
do simple cast to IOMMU MR - memory_region_get_iommu. The flag
is set in the instance init callback. This defines
memory_region_is_iommu as memory_region_get_iommu()!=NULL.
This switches MemoryRegion to IOMMUMemoryRegion in most places except
the ones where MemoryRegion may be an alias.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20170711035620.4232-2-aik@ozlabs.ru>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The start address has to be stored in big endian byte order
in the iplb.ccw block for the guest.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1499268345-12552-1-git-send-email-thuth@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
This patch is based on a similar patch from Stefan Hajnoczi -
commit c324fd0a39 ("virtio-pci: use ioeventfd even when KVM is disabled")
Do not check kvm_eventfds_enabled() when KVM is disabled since it
always returns 0. Since commit 8c56c1a592
("memory: emulate ioeventfd") it has been possible to use ioeventfds in
qtest or TCG mode.
This patch makes -device virtio-scsi-ccw,iothread=iothread0 work even
when KVM is disabled.
Currently we don't have an equivalent to "memory: emulate ioeventfd"
for ccw yet, but that this doesn't hurt and qemu-iotests 068 can pass with
skipping iothread arguments.
I have tested that virtio-scsi-ccw works under tcg both with and without
iothread.
This patch fixes qemu-iotests 068, which was accidentally merged early
despite the dependency on ioeventfd.
Signed-off-by: QingFeng Hao <haoqf@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20170704132350.11874-2-haoqf@linux.vnet.ibm.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Commit bab482d740 ("s390x/css: ccw translation infrastructure")
introduced instruction interception handler for different types of
subchannels. For emulated 3270 devices, we should assign the virtual
subchannel handler to them during device realization process, or 3270
will not work.
Fixes: bab482d740 ("s390x/css: ccw translation infrastructure")
Reviewed-by: Jing Liu <liujbjl@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Let's vmstatify virtio_ccw_save_config and virtio_ccw_load_config for
flexibility (extending using subsections) and for fun.
To achieve this we need to hack the config_vector, which is VirtIODevice
(that is common virtio) state, in the middle of the VirtioCcwDevice state
representation. This is somewhat ugly, but we have no choice because the
stream format needs to be preserved.
Almost no changes in behavior. Exception is everything that comes with
vmstate like extra bookkeeping about what's in the stream, and maybe some
extra checks and better error reporting.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-Id: <20170703213414.94298-1-pasic@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
They are indpendent, and nowadays almost every device register things
with qdev->vmsd.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
MIDA (modified indirect data addressing) is an optional facility, and
we (currently) don't support it. Let's post an operand exception if
the guest tries to set it in the orb and a channel program check
if it is set in a ccw, as specified in the Principles of Operation.
Reviewed-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Prior to the virtio-ccw-2.7 machine (and commit 2a79eb1a), our virtio
devices residing under the virtual-css bus do not have qdev_path based
migration stream identifiers (because their qdev_path is NULL). The ids
are instead generated when the device is registered as a composition of
the so called idstr, which takes the vmsd name as its value, and an
instance_id, which is which is calculated as a maximal instance_id
registered with the same idstr plus one, or zero (if none was registered
previously).
That means, under certain circumstances, one device might try, and even
succeed, to load the state of a different device. This can lead to
trouble.
Let us fail the migration if the above problem is detected during load.
How to reproduce the problem:
1) start qemu-system-s390x making sure you have the following devices
defined on your command line:
-device virtio-rng-ccw,id=rng1,devno=fe.0.0001
-device virtio-rng-ccw,id=rng2,devno=fe.0.0002
2) detach the devices and reattach in reverse order using the monitor:
(qemu) device_del rng1
(qemu) device_del rng2
(qemu) device_add virtio-rng-ccw,id=rng2,devno=fe.0.0002
(qemu) device_add virtio-rng-ccw,id=rng1,devno=fe.0.0001
3) save the state of the vm into a temporary file and quit QEMU:
(qemu) migrate "exec:gzip -c > /tmp/tmp_vmstate.gz"
(qemu) q
4) use your command line from step 1 with
-incoming "exec:gzip -c -d /tmp/tmp_vmstate.gz"
appended to reproduce the problem (while trying to to load the saved vm)
CC: qemu-stable@nongnu.org
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-Id: <20170518111405.56947-1-pasic@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
We can replace the four remaining calls of register_savevm() by
calls to register_savevm_live(). So we can remove the function and
as we don't allocate anymore the ops pointer with g_new0()
we don't have to free it then.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Split the file into public and internal interfaces. I have to rename
the external one because we can't have two include files with the same
name in the same directory. Build system gets confused. The only
exported functions are the ones that handle basic types.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
A bunch of fixes all over the place. Most notably this fixes
the new MTU feature when using vhost.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZK2bwAAoJECgfDbjSjVRpNBgIALmNG7VaixhNUlnfX1n1JBnh
+HBP2zNfvi0q5roBuPFmlziKa3IBHb2Fcte4nb6QxmPg+uoaj39AOzfrrvz210kR
h2j5Qk2bCdMeWBpxI+xDDScwi/Im23Y6KN1eZyMekFr2CaSGiqOHZPPdbsyEcHPB
VylM0uHqSTZL5JAAzEuYlH+LLfPu91HoxMsIAdNuQX+qKyM2DZ4eICBQ0zA73USt
OduZltcRMk7UpvQMqY+2iaEXapXQQEUGrP2Mo8ZyqeIl2ItC33GspqBQIKjuZdrr
tpr/T1VWsLdZnURZXyELrFqrErDXvKaP9HROwvyLyYPXZF+pJ3LA7TopS5UmfNQ=
=Z4xG
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_upstream' into staging
pci, virtio, vhost: fixes
A bunch of fixes all over the place. Most notably this fixes
the new MTU feature when using vhost.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Mon 29 May 2017 01:10:24 AM BST
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* mst/tags/for_upstream:
acpi-test: update expected files
pc: ACPI BIOS: use highest NUMA node for hotplug mem hole SRAT entry
vhost-user: pass message as a pointer to process_message_reply()
virtio_net: Bypass backends for MTU feature negotiation
intel_iommu: turn off pt before 2.9
intel_iommu: support passthrough (PT)
intel_iommu: allow dev-iotlb context entry conditionally
intel_iommu: use IOMMU_ACCESS_FLAG()
intel_iommu: provide vtd_ce_get_type()
intel_iommu: renaming context entry helpers
x86-iommu: use DeviceClass properties
memory: remove the last param in memory_region_iommu_replay()
memory: tune last param of iommu_ops.translate()
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch converts the old "is_write" bool into IOMMUAccessFlags. The
difference is that "is_write" can only express either read/write, but
sometimes what we really want is "none" here (neither read nor write).
Replay is an good example - during replay, we should not check any RW
permission bits since thats not an actual IO at all.
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Time to wire up all the call sites that request a shutdown or
reset to use the enum added in the previous patch.
It would have been less churn to keep the common case with no
arguments as meaning guest-triggered, and only modified the
host-triggered code paths, via a wrapper function, but then we'd
still have to audit that I didn't miss any host-triggered spots;
changing the signature forces us to double-check that I correctly
categorized all callers.
Since command line options can change whether a guest reset request
causes an actual reset vs. a shutdown, it's easy to also add the
information to reset requests.
Signed-off-by: Eric Blake <eblake@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au> [ppc parts]
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk> [SPARC part]
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com> [s390x parts]
Message-Id: <20170515214114.15442-5-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Implement a basic infrastructure of handling channel I/O instruction
interception for passed through subchannels:
1. Branch the code path of instruction interception handling by
SubChannel type.
2. For a passed-through subchannel, issue the ORB to kernel to do ccw
translation and perform an I/O operation.
3. Assign different condition code based on the I/O result, or
trigger a program check.
Signed-off-by: Xiao Feng Ren <renxiaof@linux.vnet.ibm.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Message-Id: <20170517004813.58227-12-bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Introduce a new callback on subchannel to handle ccw-request.
Realize the callback in vfio-ccw device. Besides, resort to
the event notifier handler to handling the ccw-request results.
1. Pread the I/O results via MMIO region.
2. Update the scsw info to guest.
3. Inject an I/O interrupt to notify guest the I/O result.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Xiao Feng Ren <renxiaof@linux.vnet.ibm.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Message-Id: <20170517004813.58227-11-bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
In order to support subchannels pass-through, we introduce a s390
subchannel device called "s390-ccw" to hold the real subchannel info.
The s390-ccw devices inherit from the abstract CcwDevice which connect
to the existing virtual-css-bus.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Message-Id: <20170517004813.58227-7-bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The S390 virtual css support already has a mechanism to create a
virtual subchannel and provide it to the guest. However, to
pass-through subchannels to a guest, we need to introduce a new
mechanism to create the subchannel according to the real device
information. Thus we reconstruct css_create_virtual_sch to a new
css_create_sch function to handle all these cases and do allocation
and initialization of the subchannel according to the device type
and machine configuration.
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Message-Id: <20170517004813.58227-6-bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The S390 virtual css support already has a mechanism to build a
virtual subchannel information block (schib) and provide virtual
subchannels to the guest. However, to pass-through subchannels to
a guest, we need to introduce a new mechanism to build its schib
according to the real device information. Thus we realize a new css
sch_build_schib function to extract the path_masks, chpids, chpid
type from sysfs. To reuse the existing code, we refactor
css_add_virtual_chpid to css_add_chpid.
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Xiao Feng Ren <renxiaof@linux.vnet.ibm.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Message-Id: <20170517004813.58227-5-bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We want to support real (i.e. not virtual) channel devices
even for guests that do not support MCSS-E (where guests may
see devices from any channel subsystem image at once). As all
virtio-ccw devices are in css 0xfe (and show up in the default
css 0 for guests not activating MCSS-E), we need an option to
squash both the virtio subchannels and e.g. passed-through
subchannels from their real css (0-3, or 0 for hosts not
activating MCSS-E) into the default css. This will be
exploited in a later patch.
Signed-off-by: Xiao Feng Ren <renxiaof@linux.vnet.ibm.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Message-Id: <20170517004813.58227-4-bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
TYPE_S390_PCI_HOST_BRIDGE is a subclass of TYPE_PCI_HOST_BRIDGE,
which is a subclass of TYPE_SYS_BUS_DEVICE. TYPE_SYS_BUS_DEVICE
already sets user_creatable=false, so we don't require an
explicit user_creatable=false assignment in
s390_pcihost_class_init().
Cc: Alexander Graf <agraf@suse.de>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Frank Blaschka <frank.blaschka@de.ibm.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Pierre Morel <pmorel@linux.vnet.ibm.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Thomas Huth <thuth@redhat.com>
Cc: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170503203604.31462-22-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
cannot_instantiate_with_device_add_yet was introduced by commit
efec3dd631 to replace no_user. It was
supposed to be a temporary measure.
When it was introduced, we had 54
cannot_instantiate_with_device_add_yet=true lines in the code.
Today (3 years later) this number has not shrunk: we now have
57 cannot_instantiate_with_device_add_yet=true lines. I think it
is safe to say it is not a temporary measure, and we won't see
the flag go away soon.
Instead of a long field name that misleads people to believe it
is temporary, replace it a shorter and less misleading field:
user_creatable.
Except for code comments, changes were generated using the
following Coccinelle patch:
@@
expression DC;
@@
(
-DC->cannot_instantiate_with_device_add_yet = false;
+DC->user_creatable = true;
|
-DC->cannot_instantiate_with_device_add_yet = true;
+DC->user_creatable = false;
)
@@
typedef ObjectClass;
expression dc;
identifier class, data;
@@
static void device_class_init(ObjectClass *class, void *data)
{
...
dc->hotpluggable = true;
+dc->user_creatable = true;
...
}
@@
@@
struct DeviceClass {
...
-bool cannot_instantiate_with_device_add_yet;
+bool user_creatable;
...
}
@@
expression DC;
@@
(
-!DC->cannot_instantiate_with_device_add_yet
+DC->user_creatable
|
-DC->cannot_instantiate_with_device_add_yet
+!DC->user_creatable
)
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Thomas Huth <thuth@redhat.com>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170503203604.31462-2-ehabkost@redhat.com>
[ehabkost: kept "TODO remove once we're there" comment]
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This patch removes redundant "qemu:" from error functions. The link to the bitesized task is:
http://wiki.qemu-project.org/Contribute/BiteSizedTasks#Error_checking
Signed-off-by: Ishani Chugh <chugh.ishani@research.iiit.ac.in>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
devices via tn3270. Actual handling of the data stream is
delegated to x3270; more info at http://wiki.qemu.org/Features/3270
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kMb4
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'cohuck/tags/s390x-3270-20170504' into staging
Basic support for using channel-attached 3270 'green-screen'
devices via tn3270. Actual handling of the data stream is
delegated to x3270; more info at http://wiki.qemu.org/Features/3270
# gpg: Signature made Thu 04 May 2017 11:36:51 AM BST
# gpg: using RSA key 0xDECF6B93C6F02FAF
# gpg: Good signature from "Cornelia Huck <conny@cornelia-huck.de>"
# gpg: aka "Cornelia Huck <cohuck@kernel.org>"
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>"
# gpg: aka "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* cohuck/tags/s390x-3270-20170504:
s390x/3270: Mark non-migratable and enable the device
s390x/3270: Detect for continued presence of a 3270 client
s390x/3270: Add the TCP socket events handler for 3270
s390x/3270: 3270 data stream handling
s390x/3270: Add emulated terminal3270 device
s390x/3270: Add abstract emulated ccw-attached 3270 device
s390x/css: Add an algorithm to find a free chpid
chardev: Basic support for TN3270
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This introduces the input and output handlers for 3270 device, setting
up the data tunnel among guest kernel, qemu and the 3270 client.
After the client connected and TN3270 handshake done, signal the not-ready
to ready status by an unsolicited device-end interrupt, and then the 3270
data stream could be handled correctly between the channel and socket.
Multiple commands generated by "Reset" key on x3270 are not supported now,
just simply terminate the connection.
Signed-off-by: Jing Liu <liujbjl@linux.vnet.ibm.com>
Signed-off-by: Yang Chen <bjcyang@linux.vnet.ibm.com>
Reviewed-by: QingFeng Hao <haoqf@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
This introduces the infrastructure for the emulated 3270
devices, which will be attached to the virtual-css-bus.
Signed-off-by: Yang Chen <bjcyang@linux.vnet.ibm.com>
Signed-off-by: Jing Liu <liujbjl@linux.vnet.ibm.com>
Reviewed-by: QingFeng Hao <haoqf@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
This introduces a function named css_find_free_chpid() to find a
free channel path. Because virtio-ccw device used zero as its
channel path number, it would be sensible to skip the reserved one
and search upwards.
Signed-off-by: Jing Liu <liujbjl@linux.vnet.ibm.com>
Reviewed-by: QingFeng Hao <haoqf@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
qemu-system-s390x currently crashes when it is started with a
virtio-scsi-pci device, e.g.:
qemu-system-s390x -nographic -enable-kvm -device virtio-scsi-pci \
-drive file=/tmp/disk.dat,if=none,id=d1,format=raw \
-device scsi-cd,drive=d1,bootindex=1
The problem is that the code in s390_gen_initial_iplb() currently assumes
that all SCSI devices are also CCW devices, which is not the case for
virtio-scsi-pci of course. Fix it by adding an appropriate check for
TYPE_CCW_DEVICE here.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <1493126327-13162-1-git-send-email-thuth@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
LOADPARM has two copies:
1. in SCP Information Block
2. in IPL Information Parameter Block
So, update SCLP intrinsics now. We always store LOADPARM in SCP
information block even if we don't have a valid IPL Information
Parameter Block.
Initial patch from Eugene (jno) Dvurechenski.
Signed-off-by: Eugene (jno) Dvurechenski <jno@linux.vnet.ibm.com>
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Insert the LOADPARM value to the IPL Information Parameter Block.
An IPL Information Parameter Block is created when "bootindex" is
specified for a device. If a user specifies "loadparm=", then we
store the loadparm value in the created IPIB for that boot device.
Initial patch from Eugene (jno) Dvurechenski.
Signed-off-by: Eugene (jno) Dvurechenski <jno@linux.vnet.ibm.com>
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
In order to specify the LOADPARM value one may now add ",loadparm=xxx"
parameter to the "-machine s390-ccw-virtio" option.
The property setter will normalize and check the value provided much
like the way the HMC does.
The value is stored, but not used at the moment.
Initial patch from Eugene (jno) Dvurechenski.
Signed-off-by: Eugene (jno) Dvurechenski <jno@linux.vnet.ibm.com>
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The I/O adapters should exist as soon as the bus/infrastructure
exists, and not only when the guest is actually trying to do something
with them. While the lazy allocation was not wrong, allocating at init
time is cleaner, both for the architecture and the code. Let's adjust
this by having each device type (currently for PCI and virtio-ccw)
register the adapters for each ISC (as now we don't know which ISC the
guest will use) as soon as it initializes.
Use a two-dimensional array io_adapters[type][isc] to store adapters
in ChannelSubSys, so that we can conveniently get the adapter id by
the helper function css_get_adapter_id(type, isc).
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Let's have a flic before we move on to initialize more specific
subsystems that make use of it.
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Let's use an enum for io adapter type, and standardize its naming to
CSS_IO_ADAPTER_* by changing S390_PCIPT_ADAPTER to CSS_IO_ADAPTER_PCI.
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
'devno' should rather be a property of the ccw device, instead of a
property of a specific virtio-ccw device. Let's consolidate it.
While we are at here, also rename CcwDevice.bus_id to CcwDevice.devno to
make things clearer.
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Expose the busids of the virtual I/O subchannel and the virtual CCW
device to ease debugging. This is needed because:
1. subchannel id are assigned dynamically, and cannot be set from
outside.
2. device busid could possibly be auto generated.
An example of using HMP to retrieve the property values of a
virtio-balloon-ccw device looks like:
[root@localhost ~]# lscss -d 0.0.0004
Device Subchan. DevType CU Type Use PIM PAM POM CHPIDs
----------------------------------------------------------------------
0.0.0004 0.0.0003 0000/00 3832/05 yes 80 80 ff 00000000 00000000
(qemu) info qtree
... ...
dev: virtio-balloon-ccw, id "balloon0"
devno = "<unset>"
ioeventfd = true
max_revision = 2 (0x2)
dev_id = "fe.0.0004"
subch_id = "fe.0.0003"
... ...
After migration, if we have the same device that shows up on a
different subchannel, we must re-fill the subch_id of the ccw
device with the new schid, or the subch_id will have an old wrong
schid value. So this also re-fills the subch_id after migration.
While we are at it, also neaten the related error handling a bit.
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Let's introduce a read-only property type that handles device ids of the
CssDevId type used for channel devices for future use. e.g. exposing the
busid of an I/O subchannel that is assigned to a ccw device.
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Wrapped printf calls inside debug macros (DPRINTF) in `if` statement.
This will ensure that printf function will always compile even if debug
output is turned off and, in turn, will prevent bitrot of the format
strings.
Signed-off-by: Danil Antonov <g.danil.anto@gmail.com>
Message-Id: <CA+KKJYBi31Bs7DtVdzZdwG2t+u5+FGiAhQpd3pqJzUX1O8Cprg@mail.gmail.com>
[CH: remove now misleading comments]
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The subchannel is a means to access a device. While the device number is
assigned by the administrator, the subchannel number is assigned by
the channel subsystem in an ascending order on cold and hot plug.
When doing unplug and replug operations, the same device may end up on
a different subchannel; for example
- We start with a device fe.1.2222, which ends up at subchannel
fe.1.0000.
- Now we detach the device, attach a device fe.1.3333 (which would get
the now-free subchannel fe.1.0000), re-attach fe.1.2222 (which ends
up at subchannel fe.1.0001) and detach fe.1.3333.
- We now have the same device (fe.1.2222) available to the guest; it
just shows up on a different subchannel.
In such a case, the subchannel numbers are different from what a
QEMU would create during cold plug when parsing the command line.
As this would cause a guest visible change on migration, we do restore
the source system's value of the subchannel number on load.
So we are now fine from the guest perspective. From the host
perspective this will cause an inconsistent state in our internal data
structures, though.
For example, the subchannel 0 might not be at array position 0. This will
lead to problems when we continue doing hot (un/re) plug operations.
Let's fix this by cleaning up our internal data structures.
Reported-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Load the network boot image into guest RAM when the boot
device selected is a network device. Use some of the reserved
space in IplBlockCcw to store the start address of the netboot
image.
A user could also use 'chreipl'(diag 308/5) to change the boot device.
So every time we update the IPLB, we need to verify if the selected
boot device is a network device so we can appropriately load the
network boot image.
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Add new field to S390IPLState to store the name of the network boot
loader.
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
For TIC CCW, bit positions 8-32 of the format-1 CCW must contain zeros;
otherwise, a program-check condition is generated. For format-0 TIC CCWs,
bits 32-63 are ignored.
To convert TIC from format-0 CCW to format-1 CCW correctly, let's clear
bits 8-32 to guarantee compatibility.
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The maximal number of virtqueues per device can be limited on a per
transport basis. For virtio-ccw this limit is defined by
VIRTIO_CCW_QUEUE_MAX, however the limitation used to come form the
number of adapter routes supported by flic (via notifiers).
Recently the limitation of the flic was adjusted so that it can
accommodate VIRTIO_QUEUE_MAX queues, and is in the meanwhile checked for
separately too.
Let us remove the transport specific limitation of virtio-ccw by
dropping VIRTIO_CCW_QUEUE_MAX and using VIRTIO_QUEUE_MAX instead.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Let's increase ADAPTER_ROUTES_MAX_GSI to VIRTIO_QUEUE_MAX which is the
largest demand foreseeable at the moment. Let us add a compatibility
macro for the previous machines so client code can maintain backwards
migration compatibility
To not mess up migration compatibility for virtio-ccw
VIRTIO_CCW_QUEUE_MAX is left at it's current value, and will be dropped
when virtio-ccw is converted to use the capability of the flic
introduced by this patch.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Currently VIRTIO_CCW_QUEUE_MAX is defined as ADAPTER_ROUTES_MAX_GSI.
That is when checking queue max we implicitly check the constraint
concerning the number of adapter routes. This won't be satisfactory any
more (due to backward migration considerations) if ADAPTER_ROUTES_MAX_GSI
changes (ADAPTER_ROUTES_MAX_GSI is going to change because we want to
support up to VIRTIO_QUEUE_MAX queues per virtio-ccw device).
Let us introduce a check on a recently introduce flic property which
gives us the compatibility machine aware limit on adapter routes.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We cannot support more than 64 virtqueues with the 64 bits provided by
classic indicators. If a driver tries to setup classic indicators
(which it is free to do even for virtio-1 devices) for a device with
more than 64 virtqueues, we should reject the attempt so that the
driver does not end up with an unusable device.
This is in preparation for bumping the number of supported virtqueues
on the ccw transport.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Wire up virtio-crypto for the CCW based VIRTIO.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
As a preparation for wiring-up virtio-crypto, the first non-transitional
virtio device on the ccw transport, let us introduce a mechanism for
disabling revision 0. This is more or less equivalent with disabling
legacy as revision 0 is legacy only, and legacy drivers use the revision
0 exclusively.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The DPRINTF approach is likely to introduce bitrot, and the preferred
way for debugging is tracing anyway. Fortunately, there are no users
(left), so nuke it.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Right now we reset all devices before we reset the cmma states. This
can result in the host kernel discarding guest pages that were
previously in the unused state but already contain a bios or a -kernel
file before the cmma reset has finished. This race results in random
guest crashes or hangs during very early reboot.
Fixes: 1cd4e0f6f0 ("s390x/cmma: clean up cmma reset")
Cc: qemu-stable@nongnu.org
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
S390PCIBusDevice is typedef'ed earlier in the file, before the hunks
that this patch modifies. The double typedef causes old versions of
GCC to complain.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1485523252-88288-1-git-send-email-pbonzini@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Current code seems to assume ring size is
always decreased but this is not required by spec:
what spec says is just that size can not exceed
the maximum. Fix it up.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <1484256243-1982-1-git-send-email-mst@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Currently there're two functions, s390_pci_setup_msix() and
s390_pci_msix_init(), for msix initialization, and being called once
for each zpci device plugging. Let's integrate them.
Moreover msix is mandatory in s390 architecture. So we ensure the pci
device being plugged supports msix. For vfio (which is the only tested
setup so far), nothing changes.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The PCI bus number is usually set by the host during the enumeration.
In the s390 architecture we neither get a Device Tree nor have an
enumeration understanding bridge devices.
Let's fake the enumeration on reset and set the PCI_PRIMARY_BUS,
PCI_SECONDARY_BUS and PCI_SUBORDINATE_BUS config entries for the
bridges.
Let's add the configuration of these three config entries on bridge hot
plug.
The bus number is calculated based on a new entry, bus_num of the
S390pciState device.
This commit is inspired by what spapr pci does.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
After PCI multibus is supported, more than 32 PCI devices could be
plugged. The current implementation of s390_pci_find_dev_by_fh()
appears low performance if there's a huge number of PCI devices
plugged. Therefore we introduce a hashtable using idx as key to store
zpci device's pointer on account of translating fh to idx very easily.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
When the hotplug handler detects a PCI bridge, the secondary bus has
been initialized by the core PCI code. We give the secondary bus the
bridge name and associate to it the IOMMU handling and
hotplug/hotunplug callbacks.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
A function may recursively call device search functions or may call
serveral different device search function. Passing the S390pciState to
search functions as an argument instead of looking up it inside the
search functions lowers the number of calling s390_get_phb().
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
In order to support a greater number of devices we use a QTAILQ
list of devices instead of a limited array.
This leads us to change:
- every lookup function s390_pci_find_xxx() for QTAILQ
- the FH_MASK_INDEX to index up to 65536 devices
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
When initializing a PCI device, an address space is required during PCI
core initialization and before the call to the embedding object hotplug
callback. To provide this AS, we allocate a S390PCIIOMMU object
containing this AS. Initialization of S390PCIIOMMU object is done
before the PCI device is completely created. So that we cannot
associate the IOMMU with the device at the moment. To track the IOMMU
object, we use g_hash functions with the PCI device's bus address as a
key to provide an array of pointers indexed by the PCI device's devfn
to the allocated IOMMU.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Currently S390PCIIOMMU is a normal struct. Let's make it inherit Object
in order to take advantage of QOM. In addition, we move some stuff
related to IOMMU from S390PCIBusDevice to S390PCIIOMMU.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We chain our compat handler via the CCW_COMPAT macros and via the
class_init function. (e.g. ccw_machine_2_7_class_options calls
ccw_machine_2_8_class_options). As all class_init functions in that
chain call SET_MACHINE_COMPAT for their compat settings, and
SET_MACHINE_COMPAT will append there is no need to do that again.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Move the generic cpu_synchronize_ functions to the common hw_accel.h header,
in order to prepare for the addition of a second hardware accelerator.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Message-Id: <f5c3cffe8d520011df1c2e5437bb814989b48332.1484045952.git.vpalatin@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Because guest mask notifier cannot be used in vhost-user mode, a boolean
flag "use_guest_notifier_mask" was added in commit 5669655aaf to disable
the use of guest mask notifier under virtio-pci. However this flag wasn't
checked in other virtio devices, such as virtio-mmio. In our tests, it
caused assertion error under "vhost-user + virtio-mmio". This patch
addresses this problem by adding a check before guest_notifier_mask is
called.
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Legacy features are those that transitional devices only
expose on the legacy interface.
Allow different ones per device class.
Cc: qemu-stable@nongnu.org # dependency for the next patch
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The instructions PCI STORE, PCI LOAD and PCI STORE BLOCK
use calls to memory_region_dispatch_write() and
memory_region_dispatch_read() but do not test the return value.
Furthermore, the instruction PCI STORE BLOCK sets up a PGM_ADDRESSING
exception when the operand 3 is not within the designated PCI address
space instead of a PGM_OPERAND exception.
Let's setup a PGM_OPERAND exception in all of these failure cases.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Let's use the generic interface to inject adapter interrupts.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
This will be used to forbid iothread configuration when the
proxy does not allow using ioeventfd. To simplify the implementation,
change the direction of the ioeventfd_disabled callback too.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This simplifies the code and removes the ioeventfd_started
and ioeventfd_set_started callback. The only difference is
in how virtio-ccw handles an error---it doesn't disable
ioeventfd forever anymore. It was the only backend to do
so, and if desired this behavior should be implemented in
virtio-bus.c.
Instead of ioeventfd_started, the ioeventfd_assign callback now
determines whether the virtio bus supports host notifiers.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This simplifies the code and removes the ioeventfd_set_disabled
callback.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Avoid "tricking" virtio-blk-dataplane into thinking that ioeventfd will be
available when it is not. This bug has always been there, but it will break
TCG+ioeventfd=on once the dataplane code will be always used when ioeventfd=on.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Coverity points out that the comparison "fid <= ZPCI_MAX_FID"
in s390_pci_generate_fid() is always true (because fid
is 32 bits and ZPCI_MAX_FID is 0xffffffff). This isn't a
bug because the real loop termination condition is
expressed later via an "if (...) break;" inside the loop,
but it is a bit odd. Rephrase the loop to avoid the
unnecessary duplicate-but-never-true conditional.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
According to the PoP, subchannels are only considered operational if
they are enabled _and_ the device number is valid. With the current
checks being enabled _or_ having a valid device number was
sufficient. This caused qemu to allow IO on subchannels that were not
enabled.
Fix the checks to require both bits to be set.
Signed-off-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Now that each S390 PCI device uses an IO region as MSIX region. The
code in s390_translate_iommu() will never be triggered. Let's remove
it.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
For efficiency we now assign one msix io region for each pci device
and provide it with the pointer to the zPCI device as opaque
parameter. In addition, we remove msix address space and add msix io
region as a subregion to the root memory region of pci device.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Pull mr variable declarations at the top of the functions instead of
mixing them up with the code. This is in preparation for followup
patches.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
We have everything needed for virtio-ccw revision 2 wired up now.
Bump the maximum supported revision reported on a device basis to
the guest so they can make use of it.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
This patch adds the response to the READ_STATUS CCW command.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
cpu model was merged with 2.8, it is wrong to abuse ri_allowed which
was enabled with 2.7.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Currently, devices are plugged before features are negotiated.
If the backend doesn't support VIRTIO_F_VERSION_1, the transport
needs to rewind some settings.
This is the case for CCW, for which a post_plugged callback had
been introduced, where max_rev field is just updated if
VIRTIO_F_VERSION_1 is not supported by the backend.
For PCI, implementing post_plugged would be much more
complicated, so it needs to know whether the backend supports
VIRTIO_F_VERSION_1 at plug time.
Currently, nothing is done for PCI. Modern capabilities get
exposed to the guest even if VIRTIO_F_VERSION_1 is not supported
by the backend, which confuses the guest.
This patch replaces existing post_plugged solution with an
approach that fits with both transports.
Features negotiation is performed before ->device_plugged() call.
A pre_plugged callback is introduced so that the transports can
set their supported features.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-stable@nongnu.org
Tested-by: Cornelia Huck <cornelia.huck@de.ibm.com> [ccw]
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
This patch is the result of coccinelle script
scripts/coccinelle/typecast.cocci
CC: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Unused function declarations were found using a simple gcc plugin and
manually verified by grepping the sources.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Implement the new virtio sockets device for host<->guest communication
using the Sockets API. Most of the work is done in a vhost kernel
driver so that virtio-vsock can hook into the AF_VSOCK address family.
The QEMU vhost-vsock device handles configuration and live migration
while the rx/tx happens in the vhost_vsock.ko Linux kernel driver.
The vsock device must be given a CID (host-wide unique address):
# qemu -device vhost-vsock-pci,id=vhost-vsock-pci0,guest-cid=3 ...
For more information see:
http://qemu-project.org/Features/VirtioVsock
[Endianness fixes and virtio-ccw support by Claudio Imbrenda
<imbrenda@linux.vnet.ibm.com>]
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
[mst: rebase to master]
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To be able to query the correct host model for the "none" machine,
let's allow runtime-instrumentation for that machine.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Message-Id: <20160905085244.99980-21-dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The mha is provided in the CPU model, so get any CPU and extract the value.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Message-Id: <20160905085244.99980-18-dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
If we have a lowest ibc, we can indicate the ibc to the guest.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Message-Id: <20160905085244.99980-17-dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We have three different blocks in the SCLP read-SCP information response
that indicate sclp features. Let's prepare propagation.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Message-Id: <20160905085244.99980-16-dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Let's factor out the common code of "read cpu info" and "read scp
info". This will make the introduction of new cpu entry fields easier.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Message-Id: <20160905085244.99980-14-dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
This patch introduces two CPU models, "host" and "qemu".
"qemu" is used as default when running under TCG. "host" is used
as default when running under KVM. "host" cannot be used without KVM.
"host" is not migration-safe. They both inherit from the base s390x CPU,
which is turned into an abstract class.
This patch also changes CPU creation to take care of the passed CPU string
and reuses common code parse_features() function for that purpose. Unknown
CPU definitions are now reported. The "-cpu ?" and "query-cpu-definition"
commands are changed to list all CPU subclasses automatically, including
migration-safety and whether static.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Message-Id: <20160905085244.99980-3-dahi@linux.vnet.ibm.com>
[CH: fix up self-assignments in s390_cpu_list, as spotted by clang]
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The cssid 255 is reserved but still valid from an architectural
point of view. However, feeding a bogus schid of 0xffffffff into
the virtio hypercall will lead to a crash:
Stack trace of thread 138363:
#0 0x00000000100d168c css_find_subch (qemu-system-s390x)
#1 0x00000000100d3290 virtio_ccw_hcall_notify
#2 0x00000000100cbf60 s390_virtio_hypercall
#3 0x000000001010ff7a handle_hypercall
#4 0x0000000010079ed4 kvm_cpu_exec (qemu-system-s390x)
#5 0x00000000100609b4 qemu_kvm_cpu_thread_fn
#6 0x000003ff8b887bb4 start_thread (libpthread.so.0)
#7 0x000003ff8b78df0a thread_start (libc.so.6)
This is because the css array was only allocated for 0..254
instead of 0..255.
Let's fix this by bumping MAX_CSSID to 255 and fencing off the
reserved cssid of 255 during css image allocation.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
With the current code a simple sclp command takes about 13000 ns
The biggest part seems to be the resolver of the object model. By
caching the sclp device the time for an sclp command goes down to
2500ns. Talking about real life scenarios, this change doubles
the speed of the sclp console when sending single bytes outputs
to /dev/console.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
