iov_to_buf() puts the buffer contents in the iov in a linearized buffer.
iov_size() gets the length of the contents in the iov.
The iov_to_buf() function is the memcpy_to_iovec() function that was
used in virtio-ballon.c.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The virtio-net code uses iov_fill() which fills an iov from a linear
buffer. The virtio-serial-bus code does something similar in an
open-coded function.
Create a new iov.c file that has iov_from_buf().
Convert virtio-net and virtio-serial-bus over to use this functionality.
virtio-net used ints to hold sizes, the new function is going to use
size_t types.
Later commits will add the opposite functionality -- going from an iov
to a linear buffer.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If adding of ports or devices in the guest fails we can send out a QMP
event so that management software can deal with it.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The check for a 0-sized write request to a guest port is not necessary;
the while loop below won't be executed in this case and all will be
fine.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The virtio-serial code doesn't mix declarations and definitions, so
separate them out on different lines.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Allow the port 'id's to be set by a user on the command line. This is
needed by management apps that will want a stable port numbering scheme
for hot-plug/unplug and migration.
Since the port numbers are shared with the guest (to identify ports in
control messages), we just send a control message to the guest
indicating addition of new ports (hot-plug) or notifying the guest of
the available ports when the guest sends us a DEVICE_READY control
message.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If the host connection to a port is closed on the destination machine
after migration, whereas the connection was open on the source, the
guest has to be informed of that.
Similar for a host connection open on the destination.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If some ports that were hot-plugged on the source are not available on
the destination, fail migration instead of trying to deref a NULL
pointer.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reported-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The number of ports on the source as well as the destination machines
should match. If they don't, it means some ports that got hotplugged on
the source aren't instantiated on the destination. Or that ports that
were hot-unplugged on the source are created on the destination.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reported-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The target could be started with max_nr_ports for a virtio-serial device
lesser than what was available on the source machine. Fail the migration
in such a case.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reported-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This clang error is harmless but worth fixing:
CC libhw32/rc4030.o
/src/qemu/hw/rc4030.c:244:66: error: if statement has empty body [-Wempty-body]
DPRINTF("read 0x%02x at " TARGET_FMT_plx "\n", val, addr);
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The bdrv_set_geometry_hint call below is not needed - it's just setting
what was just read.
Signed-off-by: Bruce Rogers <brogers@novell.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
What is known today as bdrv_open2 becomes the new bdrv_open. All remaining
callers of the old function are converted to the new one. In some places they
even know the right format, so they should have used bdrv_open2 from the
beginning.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
To be able to use config files for blkdebug, we need to make these functions
available in the tools. This involves moving two functions that can only be
built in the context of the emulator.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Fix clang error:
CC bt-l2cap.o
/src/qemu/hw/bt-l2cap.c:1000:41: error: if statement has empty body
[-Wempty-body]
/* TODO: Signal an error? */;
This means that l2cap_sframe_in() may now get called.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Andrew Zaborowski <balrogg@gmail.com>
When looking down child bus, it should look parent bridge's
bus number, not child bus's.
Optimized tail recursion and style fix.
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
When qemu is invoked with an invalid initrd file, it crashes. Following
patch prints a error message and exits if an invalid initrd is
specified. Includes changes suggested by JV.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
virtio_blk_req_complete frees the request, so we can't access it any more when
calling bdrv_mon_event. Use the pointer that was copied earlier.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Both functions report errors nicely enough now, no need for additional
messages.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Note: our device unplug methods don't need conversion work, because
they can't currently fail.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
These clang errors are harmless but worth fixing:
CC ppc-softmmu/usb-ohci.o
/src/qemu/hw/usb-ohci.c:1104:59: error: if statement has empty body [-Wempty-body]
ohci->ctrl_head, ohci->ctrl_cur);
/src/qemu/hw/usb-ohci.c:1371:57: error: if statement has empty body [-Wempty-body]
DPRINTF("usb-ohci: port %d: SUSPEND\n", portnum);
CC sparc64-softmmu/translate.o
/src/qemu/target-sparc/translate.c:3173:37: error: if statement has empty body [-Wempty-body]
; // XXX
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
use empty_slot device for the RAM which is not installed
Models without ECC don't trap when missing ram is accessed.
v0->v1 compile only once and fix indentation
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The empty_slot device emulates known to a bus but not connected devices.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
These clang errors are harmless but worth fixing:
CC libhw64/fdc.o
/src/qemu/hw/fdc.c:998:74: error: if statement has empty body [-Wempty-body]
FLOPPY_DPRINTF("Floppy digital input register: 0x%02x\n", retval);
CC libhw64/cuda.o
/src/qemu/hw/cuda.c:320:66: error: if statement has empty body [-Wempty-body]
CUDA_DPRINTF("read: reg=0x%x val=%02x\n", (int)addr, val);
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
So the userspace headers define KERNEL_STRICT_NAMES and there's no
conflict on type definition for older kernels.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
vhost in current kernels doesn't support mergeable buffers.
Disable this feature if vhost is enabled, until such
support is implemented.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
vhost driver in qemu didn't ack features, and this happens
to work because we don't really require any features. However,
it's better not to rely on this. This patch passes features to
vhost as guest acks them.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Since commit 8da3ff1809 ("MMIO callback
interface changes"), the addresses passed to the I/O functions are an
offset to the start of the area. As a consequence, there is no need to
correct the address using the value of IOBR. This make possible the use
of the default MMIO functions. Moreover the addresses are now remaped
when the value if IOBR change.
The memory area corresponds to the devices behing the PCI bus, it should
not be mapped by the PCI controller. Remove the corresponding code.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
IDE and flash are part of the R2D board, and can't be removed. Emulate
them even if there is no hard-drive plugged to the IDE or if the flash
content is empty.
So the userspace headers define KERNEL_STRICT_NAMES and there's no
conflict on type definition for older kernels.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost in current kernels doesn't support mergeable buffers.
Disable this feature if vhost is enabled, until such
support is implemented.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost driver in qemu didn't ack features, and this happens
to work because we don't really require any features. However,
it's better not to rely on this. This patch passes features to
vhost as guest acks them.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Using new pci_add_capability_at_offset makes
eepro100 code cleaner.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Stefan Weil <weil@mail.berlios.de>
Unlike virtio, device emulations need to add pci capabilities
at known offsets to match real hardware. Make this possible
by adding an appropriate API.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The guest may issue a RESET command for virtio. So far we didn't bother
to implement it, but with my new bootloader we actually need it for Linux
to get back to a safe state.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
With more files from outside the hw/ directory being placed into
libhw, avoid the need to include hw/hw.h for the sake of targ_phys_addr_t.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
There was a pointer cast warning on Ubuntu since _FORTIFY_SOURCE has been reenabled.
_FORTIFY_SOURCE had been disabled by 4a24470497
and reenabled by 849583050d.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Some drivers seems to access the reserved register in bank 0 so allow and
ignore these accesses.
Signed-off-by: Lars Munch <lars@segv.dk>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
this fixes the smc91c111 emulation which has been broken for gumstix and
mainstone and maybe others since the "MMIO callback interface changes"
8da3ff1809 was commited.
Signed-off-by: Lars Munch <lars@segv.dk>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add a destroy hook for the baum character device, to properly close the BrlAPI
connection.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The bochs vbe interface got a new register a while back, which specifies
the linear framebuffer size in 64k units. This patch adds support for
the new register to qemu. With this patch applied vgabios 0.6c works
with qemu.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Commit 15e89f5916
removed this setting, but it is still needed.
Without this patch, e100 device drivers using
interrupts don't work with qemu.
See other nic emulations which also set the
PCI interrupt pin.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pci_add_capability automatically updates PCI status and
PCI capability pointer, so use it. Use pci_reserve_capability
to make the new capability appear at the correct offset.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For some devices, this bit is always set.
For the others, it is set by default.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This ethernet device is used in Toshiba Tecra 8200 notebooks.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
By using a private device info structure
(as suggested by Gerd Hoffmann), handling of the
different device variants becomes much easier.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
SCBStatus is readonly, but most drivers which were derived
from the old Linux eepro100.c do a word write to this address
when they want to acknowledge interrupts.
So we have to mask these writes here.
The patch also removes old unused code for status read / write.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move ARMv7-M PC/SP initialization to the CPU reset routine. Add a board
reset routine to call this. Also load values directly from ROM as
images have not been copied yet.
Avoid clearing the NVIC pointer on cpu reset.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Timer with zero period (free-run) will never match.
Timer counting starts with tick value of 0x200, not from 0,
so the period must calculated from one tick less than the limit.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
After commit 702f3e0fb5, the params is
nerver NULL. It should check *params instead of params to determine
whether the params is empty.
Signed-off-by: TeLeMan <geleman@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
u_int64_t raises compiler error messages:
CC libhw32/virtio.o
/qemu/ar7/hw/virtio.c: In function ‘virtio_queue_get_avail_size’:
/qemu/ar7/hw/virtio.c:776: error: ‘u_int64_t’ undeclared (first use in this function)
/qemu/ar7/hw/virtio.c:776: error: (Each undeclared identifier is reported only once
/qemu/ar7/hw/virtio.c:776: error: for each function it appears in.)
Replacing u_int64_t by uint64_t helps.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This connects virtio-net to vhost net backend.
The code is structured in a way analogous to what we have with vnet
header capability in tap.
We start/stop backend on driver start/stop as
well as on save and vm start (for migration).
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This adds vhost net device support in qemu. Will be tied to tap device
and virtio by following patches. Raw backend is currently missing,
will be worked on/submitted separately.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Support host/guest notifiers in virtio-pci.
The last one only with kvm, that's okay
because vhost relies on kvm anyway.
Note on kvm usage: kvm ioeventfd API
is implemented on non-kvm systems as well,
this is the reason we don't need if (kvm_enabled())
around it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
make it possible to use type without header include,
simplifying header dependencies.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
vhost net backend needs to be notified when
frontend status changes. Add a callback,
similar to set_features.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
vhost needs physical addresses for ring and other queue fields,
so add APIs for these. In particular, add binding API to set
host/guest notifiers. Will be used by vhost.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
event notifiers are slightly generalized eventfd descriptors. Current
implementation depends on eventfd because vhost is the only user, and
vhost depends on eventfd anyway, but a stub is provided for non-eventfd
case.
We'll be able to further generalize this when another user comes along
and we see how to best do this.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Make vl.o compiled per target and fix a thinko in hw/acpi.c. It's not trivial
to make kvm.h consumable by compiled-once files.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Older Linux guests don't activate the bus master enable bit. So for those we
can just try to be clever and track if they set the DEVICE_OK bit even though
bus mastering is still disabled.
Under that condition we can disable the windows safety check. With that logic
in place both guests should work just fine. Without PCI hotplug breaks
virtio-net in Linux < 2.6.34 guests.
Signed-off-by: Alexander Graf <agraf@suse.de>
CC: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Mass Storage Reset and Get Max LUN are class specific requests, but
they were not marked as such in hw/usb-msd.c, moved therefore
ClassInterfaceRequest and ClassInterfaceOutRequest from hw/usb-net.c
to hw/usb.h.
Furthermore there was a problem in hw/usb-ohci.c when using DEBUG
concerning systems where size_t is a 32 bit integer (printf resulted
in a segmentation fault).
Signed-off-by: Max Reitz <max@tyndur.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Beginning with its introduction, the virtio balloon has had an overflow error
that causes 'info balloon' to misreport the actual memory size when the balloon
itself becomes larger than 4G. Use a cast when converting dev->actual from
pages to kB to prevent overflows.
Before:
(qemu) info balloon
balloon: actual=5120
(qemu) balloon 1025
(qemu) info balloon
balloon: actual=1025
(qemu) balloon 1024
(qemu) info balloon
balloon: actual=5120
After:
(qemu) info balloon
balloon: actual=5120
(qemu) balloon 1025
(qemu) info balloon
balloon: actual=1025
(qemu) balloon 1024
(qemu) info balloon
balloon: actual=1024
Signed-off-by: Adam Litke <agl@us.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Make win2k install hack unconditional as it is still restricted to
x86 only in vl.c.
Replace TARGET_PAGE_SIZE and 4096 with PAGE_SIZE.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This fixes a copy/paste bug introduced in commit
2d48377a85 that pushed TARGET_WORDS_BIGENDIAN
dependency to board level.
Signed-off-by: Lars Munch <lars@segv.dk>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Convert pci_host_conf_register_mmio_noswap(x) to
pci_host_conf_register_mmio(x, 0).
Convert pci_host_conf_register_mmio(x) to
pci_host_conf_register_mmio(x, 1) for big endian hosts, all cases
happen to be BE.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
x86 definitions (especially CPUState uses) prevent many files from
being compiled within libhw.
Move x86 specific declarations (APIC stuff) to a separate file.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This reverts commit d7234f4d7e.
Conflicts:
hw/xen_machine_pv.c
This should have never been committed.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
All of these users have global state so we really don't see a benefit from
exit_notifier. However, using exit_notifier means that there's one less
justification for having global state in the first place.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
And convert usb-hid to use it (to avoid regression with bisection)
Right now, when we do info mice and we've added a usb tablet, we don't see it
until the guest starts using the tablet. We implement this behavior in order
to provide a means to delay registration of a mouse handler since we treat
the last registered handler as the current handler.
This is a usability problem though as we would like to give the user feedback
that they've either 1) not added an absolute device 2) there is an absolute
device but the guest isn't using it 3) we have an absolute device and it's
active.
By using QTAILQ and having an explicit activation function that moves the
handler to the front of the queue, we can implement the same semantics as
before with respect to automatically switching to usb tablet while providing
the user with a whole lot more information.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When building with -DNDEBUG, assert(0) will not stop execution
so it must not be used for abnormal termination.
Use cpu_abort() when in CPU context, abort() otherwise.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The usb-msd device emulation needs some small tweaks in the requests
emulations. For instance, the reset/maxlun requests are class/interface
specific so requests for them with the type class and recipient interface
bits sets have to be handled.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
In case s->version is shorter than 4 bytes we overflow the memcpy src
buffer. Fix it by clearing the target buffer, then copy only the
amount of bytes we actually have.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Don't rely on CDROM hint for read_only attribute
Signed-off-by: Naphtali Sprei <nsprei@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Just tell main_loop_wait whether to be blocking or nonblocking, so that
there is no need to call qemu_cpus_have_work from the timer subsystem.
Instead, tcg_cpu_exec can say "we want the main loop not to block because
we have stuff to do".
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When working with the VM state (for loadvm/savevm and migration), it is not
valid to load and store pointers since the validity of those pointers cannot be
assured in the new qemu address space. Therefore, virtio_balloon_save() and
virtio_balloon_load() must not handle the stats-related fields in struct
VirtIOBalloon.
If a memory stats request is in-flight at the time of a migration or savevm,
the request will not complete and should be resubmitted once migration or
loadvm completes. Note that this extremely small race window can only be
triggered using QMP so it is not possible to hang the user monitor.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add a logical block size attribute as various guest side tools only
increase the filesystem sector size based on it, not the advisory
physical block size.
For scsi we already have support for a different logical block size
in place for CDROMs that we can built upon. Only my recent block
device characteristics VPD page needs some fixups. Note that we
leave the logial block size for CDROMs hardcoded as the 2k value
is expected for it in general.
For virtio-blk we already have a feature flag claiming to support
a variable logical block size that was added for the s390 kuli
hypervisor. Interestingly it does not actually change the units
in which the protocol works, which is still fixed at 512 bytes,
but only communicates a different minimum I/O granularity. So
all we need to do in virtio is to add a trap for unaligned I/O
and round down the device size to the next multiple of the logical
block size.
IDE does not support any other logical block size than 512 bytes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Many usbdevice_init implementors assume params is non-NULL.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
QEMU uses a fixed page size for the CPU TLB. If the guest uses large
pages then we effectively split these into multiple smaller pages, and
populate the corresponding TLB entries on demand.
When the guest invalidates the TLB by virtual address we must invalidate
all entries covered by the large page. However the address used to
invalidate the entry may not be present in the QEMU TLB, so we do not
know which regions to clear.
Implementing a full vaiable size TLB is hard and slow, so just keep a
simple address/mask pair to record which addresses may have been mapped by
large pages. If the guest invalidates this region then flush the
whole TLB.
Signed-off-by: Paul Brook <paul@codesourcery.com>
We sometimes permit omitting the first option name, for example
-device foo is short for -device driver=foo. The name to use
("driver" in the example) is passed as argument to qemu_opts_parse().
For each QemuOptsList, we use at most one such name.
Move the name into QemuOptsList, and pass whether to permit the
abbreviation. This ensures continued consistency, and simplifies the
commit after next in this series.
This reverts commit 3ced9f7a36.
The next commit will convert all of qdev_device_add() to QError, and
it'll be clearer with this partial conversion reverted.
Users can't set them, so qdev_device_help() shouldn't list them. Fix
that. Also make qdev_prop_parse() hide them instead of printing a
meaningless "has no parser" error message.
Their value means nothing to users, so qdev_print_props() shouldn't
print it. Fix by removing their print method.
Their only use is dirty hacks. Document that.
Users can't create them, so qdev_device_help() shouldn't list them.
Fix that.
Also make qdev_device_add() pretend they don't exist. Before, it
rejected them with a "can't be added via command line" message, which
wasn't quite right for monitor command device_add.
error_report() terminates the message with a newline. Strip it it
from its arguments.
This fixes a few error messages lacking a newline:
net_handle_fd_param()'s "No file descriptor named %s found", and
tap_open()'s "vnet_hdr=1 requested, but no kernel support for
IFF_VNET_HDR available" (all three versions).
There's one place that passes arguments without newlines
intentionally: load_vmstate(). Fix it up.
Commit 30d335d6 converted an informational message from
monitor_printf() to qemu_error(), probably because the latter doesn't
need a mon argument. A later commit will make qemu_error() print
additional stuff that is only appropriate for proper errors, and then
this will break. Clean it up.
qbus_find() adds an informational line to error messages, and prints
both lines with one qemu_error(). Use error_printf() for the
informational line instead.
While there, simplify: instead of printing buffers filled by
qbus_list_bus() and qbus_list_dev() in one go, make them print it.
qdev_device_help() prints device information with qemu_error(). A
later commit will make qemu_error() print additional stuff that is
only appropriate for proper errors, and then this will break. Use
error_printf() instead.
While there, simplify: instead of printing a buffer filled by
qdev_print_devinfo() in one go, make qdev_print_devinfo() print it.
The old test assumes that "hotplugged" implies "we have a current
monitor for reading the key". This is in fact true, but it's not
obviously true.
Aside: if it were false, we could pass a null pointer to
monitor_read_bdrv_key_start(), which would then crash.
The previous commit permits us to check for "we have a current
monitor" directly, so do that.
Code duplicated in commit 0ecdffbb. The two versions are similar, but
not identical:
* cmos_init() reports errors to stderr, pc_boot_set() via
qemu_error(). The latter is fine for both, so pick that for the
common code.
* cmos_init() obeys fd_bootchk, pc_boot_set() ignores it. Make it a
parameter of the common code.
Commit 0ecdffbb created pc_boot_set() for use from monitor command
"boot_set", via qemu_boot_set(). pc_boot_set() reports errors to
cur_mon, which works fine for monitor code.
Commit e0f084bf reused the function int reset handler
restore_boot_devices(). Use of cur_mon is problematic in that
context. For instance, the "Too many boot devices for PC" error for
"-boot order=abcdefgh,once=c" goes to the monitor instead of stderr.
The monitor may not even exist.
Fix by switching to qemu_error().
A few machines need to translate the ELF header addresses into physical
addresses. Currently the only possibility is to add a value to the
addresses.
This patch replaces the addend argument by and a translation function
and an opaque passed to the function. A NULL function does not translate
the address.
The patch also convert all machines that have an addend, simplify the
PowerPC kernel loading and fix the MIPS kernel loading using this new
feature. Other machines may benefit from this feature.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Real pcnet device (AT2450) apparently has subsystem
device and vendor id set to 0, this is out of spec
(which requires that vendor id is obtained from PCI SIG)
but windows xp driver seems to need this in order
to associate.
qemu sets pci subsystem id to qumranet/qemu
since d350d97d19,
debian does not yet have this patch.
https://bugzilla.redhat.com/show_bug.cgi?id=521247
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Anthony Liguori <aliguori@us.ibm.com>
eepro100 uses macros which rely on a specific
local variable name (pci_conf) which is scary.
Some of the uses are wrong or unnecessary,
remove them. The rest are small in number, open-code
them using pci_set_xx functions.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
here's a trivial patch to fix the spelling of "compatibility":
Signed-off-by: Vagrant Cascadian <vagrant@freegeek.org>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Fix the floppy controller init wrappers to set the drive properties
only in case the DriveInfo pointers passed in are non NULL. This allows
to set the properties using -global.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
It's emitted whenever the watchdog device's timer expires. The action
taken is provided in the 'data' member.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add led status notification support to the usb kbd driver.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add led status notification support to the ps/2 kbd driver.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
You're supposed to use scsi-generic for that. Which rejects anything
but /dev/sg*.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Guest device and host netdev are peers, i.e. it's a 1:1 relation.
However, we fail to enforce that:
$ qemu -nodefaults --nographic -netdev user,id=net0 -device e1000,netdev=net0 -device virtio-net-pci,netdev=net0 -monitor stdio
QEMU 0.12.50 monitor - type 'help' for more information
(qemu) info network
Devices not on any VLAN:
net0: net=10.0.2.0, restricted=n peer=virtio-net-pci.0
e1000.0: model=e1000,macaddr=52:54:00:12:34:56 peer=net0
virtio-net-pci.0: model=virtio-net-pci,macaddr=52:54:00:12:34:57 peer=net0
It's all downhill from there.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Property "vlan" reports "failed to parse" even when the value parses
just fine, but the result doesn't name an existing VLAN.
Similarly, properties "drive", "chr" and "netdev" misleadingly report
"failed to parse" when the value doesn't name an existing host device.
Change PropertyInfo method parse to return an error code, so that
qdev_prop_parse() can report the error more accurately.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Use the named constant instead of -1.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reported-by: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
net.c used a constant to signify no MSI vectors were specified. Extend
that to all qdev devices.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reported-by: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
According to AMD document 21485D pp.141, APROMWE is bit 8 of BCR2.
Signed-off-by: Christopher Kilgour <techie@whiterocker.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The next commit will move the STOP event into do_vm_stop(), to
have the expected event sequence we need to emit the I/O error
event before calling vm_stop().
The expected sequence is:
{ "event": "BLOCK_IO_ERROR" [...] }
{ "event": "STOP" }
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Disable the MULTIPORT feature and MSI vectors for the 0.12 machine
types; those features are added only for 0.13 onwards.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add a 0.12 machine type for compatibility with older versions. Mark the
default one as 0.13.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Commit 428c149b0b modified the argument
that virtio_blk_init takes. Update the s390 bus code that calls this
function.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
UART_IIR_THRI is not a mask, but a possible value for the IIR ID.
Use UART_IIR_ID to extract this value.
Broken by commit 71e605f803.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
As we hard-wire the BSP to CPU 0 anyway and cpuid_apic_id equals
cpu_index, bsp_to_cpu can also be based on the latter directly. This
will help an early user of it: KVM while initializing mp_state.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This grand cleanup drops all reset and vmsave/load related
synchronization points in favor of four(!) generic hooks:
- cpu_synchronize_all_states in qemu_savevm_state_complete
(initial sync from kernel before vmsave)
- cpu_synchronize_all_post_init in qemu_loadvm_state
(writeback after vmload)
- cpu_synchronize_all_post_init in main after machine init
- cpu_synchronize_all_post_reset in qemu_system_reset
(writeback after system reset)
These writeback points + the existing one of VCPU exec after
cpu_synchronize_state map on three levels of writeback:
- KVM_PUT_RUNTIME_STATE (during runtime, other VCPUs continue to run)
- KVM_PUT_RESET_STATE (on synchronous system reset, all VCPUs stopped)
- KVM_PUT_FULL_STATE (on init or vmload, all VCPUs stopped as well)
This level is passed to the arch-specific VCPU state writing function
that will decide which concrete substates need to be written. That way,
no writer of load, save or reset functions that interact with in-kernel
KVM states will ever have to worry about synchronization again. That
also means that a lot of reasons for races, segfaults and deadlocks are
eliminated.
cpu_synchronize_state remains untouched, just as Anthony suggested. We
continue to need it before reading or writing of VCPU states that are
also tracked by in-kernel KVM subsystems.
Consequently, this patch removes many cpu_synchronize_state calls that
are now redundant, just like remaining explicit register syncs.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Instead of allocating a separate chunk for the first 640KB and another
for 1MB+, allocate one large chunk. This plays well in terms of alignment
and size with large pages.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
I always try to keep standard includes sorted
and add a comment why they are there (so they
can be removed when they are no longer needed).
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
C++ comments are unwanted, so this is fixed here.
* Replace C++ comments by C comments.
* Put code which was deactivated by a C++ comment in #if 0...#endif.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Real hardware would run an internal self-test.
The emulation just returns a passed status.
Original patch was from Reimar Döffinger, thanks.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move code which reads the command block to the
new function read_cb. The patch also fixes some
endianess issues related to the command block
and moves declarations of local variables to
the beginning of the block.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is no need for a local variable "status".
Using tx.status makes it clearer which status
is addressed.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
CU Start is allowed when the CU is in the idle or suspended state.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The RNR interrupt is triggered under these conditions:
* the RU is not ready to receive a frame due to missing resources
* the RU is ready and a RU abort command was requested
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When compiling with -Wshadow, gcc gives a warning
which is fixed by renaming stat -> status.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Instead of magic numbers like 0x8000, symbolic names are used
for the SCB command and status bits.
There are too many configuration bits to use symbolic names
there, too. Using the BIT macro is a little help when comparing
code and documentation.
For the same reason, some other constants were replaced by
the BITS macro.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add descriptions for all devices.
These descriptions are shown when users call
qemu -device ?
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Only two boot ROM files are needed for all devices.
* Add these GPXE ROM files using new naming convention
(as discussed on qemu-devel). Both files were created
with http://rom-o-matic.net/, PCI vendor / device ids
as in ROM filenames and option BANNER_TIMEOUT = 0.
* Remove old PXE ROM file for i82559er.
It was replaced by gpxe-eepro100-80861209.rom.
* Update pc-bios/README (and sort entries).
Full support still needs additional eepro100 fixes.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The phy handling was wrong for PXE, GPXE boot:
GPXE's eepro100 driver did not detect a valid link.
This is fixed here.
V2 - Use UPPER_CASE for enum values
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Some system control block registers were addressed
using their offset value. Use symbolic names now
and clean the documentation.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When debug output was enabled (by defining DEBUG_EEPRO100),
some debug messages resulted in a compiler error.
This is fixed here.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move userland PALcode handling into linux-user main loop so that
we can send signals from there. This also makes alpha_palcode.c
system-level only, so don't build it for userland. Add defines
for GENTRAP PALcall mapping to signals.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Since kernel uimage is getting bigger,
old fixed loading bases will result in regions overlap.
Add pad for fdt and ramdisk, so that they won't overlap with uimage.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
It's convinent to use rom to checking overlap, to reset etc.
And uImage and ramdisk loading has already moved to it.
Also, after we add fdt to rom, free it.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
So that the following registers init could be flushed back to kvm.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Acked-by: Hollis Blanchard <hollis@penguinppc.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
If -usbdevice is used on a machine with no USB busses, usb_create
will fail and return NULL. Patch below handles this failure gracefully
rather than crashing when we try to init the device.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Add a QEMU timer only when needed (timeout status not set, timeout
irq wanted and timer set).
This patch is required for Darwin. Patch has been tested under
FreeBSD, Darwin and Linux.
Signed-off-by: Frediano Ziglio <freddy77@gmail.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
o Implement receive overrun status. The FreeBSD uart driver
relies on this status in it's probe routine to determine the size
of the FIFO supported.
o As per the 16550 spec, do not overwrite the RX FIFO on an RX overrun.
o Do not allow TX or RX FIFO overruns to increment the data valid count
beyond the size of the FIFO.
o For reads of the IIR register, only clear the "TX holding register
emtpy interrupt" if the read reports this interrupt. This is required
by the specification and avoids losing TX interrupts when other,
higher priority interrupts (usually RX) are reported first.
Signed-off-by: Justin T. Gibbs <gibbs@FreeBSD.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
pci_data_write ignores high 8 bit in address,
so there seems to be no need to set them
in apb_pci.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
cc1: warnings being treated as errors
/src/qemu/hw/pl181.c: In function 'pl181_fifo_run':
/src/qemu/hw/pl181.c:185: error: 'value' may be used uninitialized in this function
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The PL181 data transfer loop incorrectly terminates after the last FIFO
word is popped, discarding the last 3 bytes of data on a write transfer.
Signed-off-by: Paul Brook <paul@codesourcery.com>
/src/qemu/hw/ide/core.c: In function 'ide_drive_pre_save':
/src/qemu/hw/ide/core.c:2740: warning: comparison is always false due to limited range of data type
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
If the device can't be created, don't leak the QemuOpts and release the id of
the device that should have been added by the failed device_add.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Hi,
Kevin and I have agreed on the approach for this one now. So here is
the latest version of the patch for QEMU, submitting e820 reservation
entries via fw_cfg.
Cheers,
Jes
Use qemu-cfg to provide the BIOS with an optional table of e820 entries.
Notify the BIOS of the location of the TSS+EPT range to by reserving
it via the e820 table.
This matches a corresponding patch for Seabios, however older versions
of Seabios will default to the hardcoded address range and stay
compatible with current QEMU.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Save/restore information necessary to continue in progress PIO/ATAPI CMD
transfers.
This includes the IO buffer.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Michael noted we don't allow disabling of MSI for the virtio-serial-pci
device. Fix that.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
CC: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Since commit 98b19252cf, all
serial devices declare MULTIPORT feature.
To allow 0.12 compatibility, we should clear this when
max_nr_ports is 1.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
virtio-serial-pci can support multiple ports in the current development
version that will become 0.13. Add compatibility options for the 0.12
and 0.11 pc machine types.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The version 0.13 will be the new default and compatibility options will
be added to the 0.12 version.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
I found that the QEMU USB keyboard support does not work properly with
the Set_Idle command. Once a non-zero value is given to Set_Idle,
then the keyboard reports an event on every poll - not based on the
time issued in the Set_Idle command.
I changed the code (see patch below) and it works for me. I'm not
that familiar with the qemu internals, so I'm not sure if this is the
best way to implement this feature.
-Kevin
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Don't raise irq when not enabled.
Raise irq on enabling if DMA_INTR is set
Don't clear irq unless it was raised by DMA, as there are other irq sources
Don't set DMA_INTR bit spuriously.
v1->v2:
- Don't clear irq unless it was raised by DMA
- Raise irq on enabling if DMA_INTR is set
- Assume revertion of 787cfbc432
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Cleanup versatile_pci: no need to re-set fields
to zero (pci core sets 0 already), use set_word
for status field. Compile-tested only, but seems obvious.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Anthony Liguori <aliguori@us.ibm.com>
This converts versatile_pci to use symbolic
constants. Verified by comparing binary to
original one.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Anthony Liguori <aliguori@us.ibm.com>
Linux with CONFIG_PPC64 doesn't support ADB devices anymore, so we have to
use USB for keyboard and mouse.
This patch enables USB per default on U3 and adds a virtual keyboard and mouse
there.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
While trying to find the right channel number for the DBDMA emulation I
stumbled across segmentation faults that were purely triggered by the guest.
The guest should never have the possiblity to segfault us, so let's check
all indirect function calls on a channel, so the code even works for channels
that have not been reserved.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Per default Linux doesn't come with a lot of storage adapters enabled on
Mac configurations. The one that's pretty much always present is the pmac-ide,
while the cmd64x is almost never included in any distribution.
So let's switch to use the MacIO based IDE controller. There is corresponding
OpenBIOS code to get interrupts working properly.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Our guest systems need to know by how much the timebase increases every second,
so there usually is a "timebase-frequency" property in the cpu leaf of the
device tree.
This property is missing in OpenBIOS.
With qemu, Linux's fallback timebase speed and qemu's internal timebase speed
match up. With KVM, that is no longer true. The guest is running at the same
timebase speed as the host.
This leads to massive timing problems. On my test machine, a "sleep 2" takes
about 14 seconds with KVM enabled.
This patch exports the timebase frequency to OpenBIOS, so it can then put them
into the device tree.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The interrupt code as is didn't really work for me. I couldn't even convince
Linux to take interrupt 9 in an interrupt-map.
So let's do this right. Let's map all PCI interrupts to 0x1b - 0x1e. That way
we're at least a small step closer to what real hardware does.
I also took the interrupt pin to line conversion from OpenBIOS, which at least
assures us we're compatible with our firmware :-).
A dump of the PCI interrupt-map from a U2 (iBook):
00009000 00000000 00000000 00000000 ff97c528 00000034 00000001
0000d800 00000000 00000000 00000000 ff97c528 0000003f 00000001
0000c000 00000000 00000000 00000000 ff97c528 0000001b 00000001
0000c800 00000000 00000000 00000000 ff97c528 0000001c 00000001
0000d000 00000000 00000000 00000000 ff97c528 0000001d 00000001
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To ease debugging and to know what we're lacking, I found it really useful to
have an lspci dump of a real U3 based G5 around. So I added a comment for it.
If people don't think it's important enough to include this information in the
sources, just don't apply this patch.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The "Mac99" type so far defines a "U2" based configuration. Unfortunately,
there have never been any U2 based PPC64 machines. That's what the U3 was
developed for.
So let's split the Mac99 machine in a PPC64 and a PPC32 machine. The PPC32
machine stays "Mac99", while the PPC64 one becomes "Mac99_U3". All peripherals
stay the same.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The Uninorth PCI bridge requires different layouts in its PCI config space
accessors.
This patch introduces a conversion function that makes it compatible with
the way Linux accesses it.
I also kept an OpenBIOS compatibility hack in. I think it'd be better to
take small steps here and do the config space access rework in OpenBIOS
later on. When that's done we can remove that hack.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Remove useless set to zero lines. Latency programming should be
done by BIOS, reset value is zero.
Add revision to APB, don't enable PCI_COMMAND_MASTER and set status
according to APB specification.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Commit c2039bd0ff made rom loading
automatic for non-PC architectures. Remove now mostly unused
conditional rom loading support.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch fixes 525e05147d.
pci host bridge doesn't have header type of bridge.
The check should be by header type, instead of pci class device.
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Export the physical block size in the ATA IDENTIFY command. The
other topology values are not supported in ATA so skip them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Export the physical block size in the READ CAPACITY (16) command,
and add the new block limits VPD page to export the minimum and
optiomal I/O sizes.
Note that we also need to bump the scsi revision level to SPC-2
as that is the minimum requirement by at least the Linux kernel
to try READ CAPACITY (16) first and look at the block limits VPD
page.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Export all topology information in the block config structure,
guarded by a new VIRTIO_BLK_F_TOPOLOGY feature flag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add three new qdev properties to export block topology information to
the guest. This is needed to get optimal I/O alignment for RAID arrays
or SSDs.
The options are:
- physical_block_size to specify the physical block size of the device,
this is going to increase from 512 bytes to 4096 kilobytes for many
modern storage devices
- min_io_size to specify the minimal I/O size without performance impact,
this is typically set to the RAID chunk size for arrays.
- opt_io_size to specify the optimal sustained I/O size, this is
typically the RAID stripe width for arrays.
I decided to not auto-probe these values from blkid which might easily
be possible as I don't know how to deal with these issues on migration.
Note that we specificly only set the physical_block_size, and not the
logial one which is the unit all I/O is described in. The reason for
that is that IDE does not support increasing the logical block size and
at last for now I want to stick to one meachnisms in queue and allow
for easy switching of transports for a given backing image which would
not be possible if scsi and virtio use real 4k sectors, while ide only
uses the physical block exponent.
To make this more common for the different block drivers introduce a
new BlockConf structure holding all common block properties and a
DEFINE_BLOCK_PROPERTIES macro to add them all together, mirroring
what is done for network drivers. Also switch over all block drivers
to use it, except for the floppy driver which has weird driveA/driveB
properties and probably won't require any advanced block options ever.
Example usage for a virtio device with 4k physical block size and
8k optimal I/O size:
-drive file=scratch.img,media=disk,cache=none,id=scratch \
-device virtio-blk-pci,drive=scratch,physical_block_size=4096,opt_io_size=8192
aliguori: updated patch to take into account BLOCK events
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The addition of the whole ATA IDENTIY page caused the config space to
go above the allowed size in the PCI spec, and thus the feature was
already reverted in the Linux guest driver and disabled by default in
qemu.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
It's not needed to check the return of qobject_from_jsonf()
anymore, as an assert() has been added there.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Fix a race condition where qemu finds that there are not enough virtio
ring buffers available and the guest make more buffers available before
qemu can enable notifications.
Signed-off-by: Tom Lendacky <toml@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This fixes a segfault due to buffer overrun in the usb-serial device.
The memcpy was incrementing the start location by recv_used yet, the
computation of first_size (how much to write at the end of the buffer
before wrapping to the front) was not accounting for it. This causes the
next element after the receive buffer (recv_ptr) to get overwritten with
random data.
Signed-off-by: David Ahern <daahern@cisco.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
I have streaming audio devices working within qemu-kvm. This is a port
of the changes to qemu.
Streaming audio generates a series of isochronous requests that are
repetitive and time sensitive. The URBs need to be submitted in
consecutive USB frames and responses need to be handled in a timely manner.
Summary of the changes for isochronous requests:
1. The initial 'valid' value is increased to 32. It needs to be higher
than its current value of 10 since the host adds a 10 frame delay to the
scheduling of the first request; if valid is set to 10 the first
isochronous request times out and qemu cancels it. 32 was chosen as a
nice round number, and it is used in the path where a TD-async pairing
already exists.
2. The token field in the TD is *not* unique for isochronous requests,
so it is not a good choice for finding a matching async request. The
buffer (where to write the guest data) is unique, so use that value instead.
3. TD's for isochronous request need to be completed in the async
completion handler so that data is pushed to the guest as soon as it is
available. The uhci code currently attempts to process complete
isochronous TDs the next time the UHCI frame with the request is
processed. The results in lost data since the async requests will have
long since timed out based on the valid parameter. Increasing the valid
value is not acceptable as it introduces a 1+ second delay in the data
getting pushed to the guest.
4. The frame timer needs to be run on 1 msec intervals. Currently, the
expire time for the processing the next frame is computed after the
processing of each frame. This regularly causes the scheduling of frames
to shift in time. When this happens the periodic scheduling of the
requests is broken and the subsequent request is seen as a new request
by the host resulting in a 10 msec delay (first isochronous request is
scheduled for 10 frames from when the URB is submitted).
[ For what's worth a small change is needed to the guest driver to have
more outstanding URBs (at least 4 URBs with 5 packets per URB).]
Signed-off-by: David Ahern <daahern@cisco.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Just call bdrv_mon_event() in the right place.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Just call bdrv_mon_event() in the right place.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Just call bdrv_mon_event() in the right place.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The write the the PA_POWOFF register is currently ignored. Fix that by
calling qemu_system_shutdown_request() when a poweroff is requested.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
typo in c021f8e65f.
comparison fix.
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When several PCI bridges were in use, monitor command "info pci" would
enter into infinite loop. Buses behind the bridge were not discoverable
because secondary and subordinate bus numbers were not used properly.
Other buses were not found because bus search terminated on first miss.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The vmport "device" accesses the VCPU registers, so it requires proper
cpu_synchronize_state. Add it to vmport_ioport_read, which also
synchronizes vmport_ioport_write.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
This provides the same information as reverted commit 2ba6edf0. Not
much, just better than nothing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Option "-device DRIVER,?" and monitor command "device_add DRIVER,?"
print the supported properties instead of creating a device. The
former also terminates the program.
This is commit 2ba6edf0 (just reverted) done right.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This reverts commit 2ba6edf0dd.
The commit has two issues:
* When it runs from the monitor, e.g. "device_add e1000,?", it prints
to stderr instead of the monitor.
* Help looks to callers just like failed device creation. This makes
main() exit unsuccessfully on "-device e1000,?".
We need to do this differently.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This reverts commit 922910ce42.
The commit has four issues:
* When it runs from the monitor, e.g. "device_add e1000,mac=?", it
prints to stderr instead of the monitor.
* Help looks to callers just like failed device creation. This makes
main() exit unsuccessfully on "-device e1000,mac=?".
* It has an undocumented side effect on -global: "-global e1000.mac=?"
prints help, but only when we actually add an e1000 device.
* It does not work for properties that accept the value "?".
We need to do this differently.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Help was shoehorned into device creation, qdev_device_add(). Since
help doesn't create a device, it returns NULL, which looks to callers
just like failed device creation. Monitor handler do_device_add()
doesn't care, but main() exits unsuccessfully.
Move help out of device creation, into new qdev_device_help().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If an I/O request fails right away instead of getting an error only in the
callback, we still need to consider rerror/werror.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Current code assumes that only write requests are ever going to be restarted.
This is wrong since rerror=stop exists. Instead of directly starting writes,
use the same request processing as used for new requests.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
We need a function that handles a single request. Create one by splitting out
code from virtio_blk_handle_output.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This fixes CONFIG_FB_CIRRUS for Linux guests and probably much more:
When switching away from linearly mapped vram, we also have to restore
the I/O handlers for the LFB.
This regression was once introduced by commit 2bec46dc97.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This commit enables one to use multiple virtio-serial devices and to
assign ports to arbitrary devices like this:
-device virtio-serial,id=foo -device virtio-serial,id=bar \
-device virtserialport,bus=foo.0,name=foo \
-device virtserialport,bus=bar.0,name=bar
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
sparc64 timer has tick counter which can be set and read,
and tick compare value used as deadline to fire timer interrupt.
The timer is not used as periodic timer, instead deadline
is set each time new timer interrupt is needed.
v3 -> v4:
- coding style
v2 -> v3:
- added missing timer debug output macro
- CPUTimer struct and typedef moved to cpu.h
- change CPU_SAVE_VERSION to 6, older save formats not supported
v1 -> v2:
- new conversion helpers cpu_to_timer_ticks and timer_to_cpu_ticks
- save offset from clock source to implement cpu_tick_set_count
- renamed struct sun4u_timer to CPUTimer
- load and save cpu timers
v0 -> v1:
- coding style
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Buffer block writes to avoid flushing every word access onto backing
storage device. This significantly speeds up flash emulation for flashes
connected through an 8 or 16-bit bus combined with backing storage (-pflash).
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@petalogix.com>
When using ballooning to manage overcommitted memory on a host, a system for
guests to communicate their memory usage to the host can provide information
that will minimize the impact of ballooning on the guests. The current method
employs a daemon running in each guest that communicates memory statistics to a
host daemon at a specified time interval. The host daemon aggregates this
information and inflates and/or deflates balloons according to the level of
host memory pressure. This approach is effective but overly complex since a
daemon must be installed inside each guest and coordinated to communicate with
the host. A simpler approach is to collect memory statistics in the virtio
balloon driver and communicate them directly to the hypervisor.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Win32 suffers from a very big memory leak when dealing with SCSI devices.
Each read/write request allocates memory with qemu_memalign (ie
VirtualAlloc) but frees it with qemu_free (ie free).
Pair all qemu_memalign() calls with qemu_vfree() to prevent such leaks.
Signed-off-by: Herve Poussineau <hpoussin@reactos.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
PCI bridges' qdev info structures must indicate bridge header type,
otherwise critical bridge registers (esp. PCI_PRIMARY_BUS,
PCI_SECONDARY_BUS, PCI_SUBORDINATE_BUS) will not be writable.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This file was renamed to ease the reviews of the recent changes
that went in.
Now that the changes are done, rename the file back to its original
name.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If migration takes place between write of the bmdma address register and
write of the command register (to initiate DMA), the destination will
not properly start the DMA op, hanging the guest:
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.00: cmd c8/00:16:41:00:00/00:00:00:00:00/e0 tag 0 dma 11264 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
Fix by sending current transfer information in the migration data.
We need to update ide version to 4 for this to work. As we don't
have subsectios, we need to chain the update increase until
vmstate_ide_pci (quintela)
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This commit completes the do_pci_info() conversion to
QObject by adding support to PCI bridge devices.
This is done by recursively adding devices in the
"pci_bridge" key.
IMPORTANT: This code is being added separately because I could
NOT test it properly. According to Michael Tsirkin, it depends
on ultrasparc and it would take time to do the proper setup.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The returned QObject is a QList of all buses. Each bus is
represented by a QDict, which has a key with a QList of all
PCI devices attached to it. Each device is represented by
a QDict.
As has happended to other complex conversions, it's hard to
split this commit as part of it are new functions which are
called by each other.
IMPORTANT: support for printing PCI bridge attached devices
is NOT part of this commit, it's going to be added by the
next commit, as it's untested.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When called with property value "?",
a help text will be printed (instead of an error message).
This is useful for command lines like
qemu -device e1000,mac=?
and is already standard for other command line options.
A better help text could be provided by extending
the Property structure with a desc field.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When called with property "?", a list of supported
properties will be printed (instead of an error message).
This is useful for command lines like
qemu -device e1000,?
and was already standard for other options like model=?
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Fix HdrS offsets for Sparc64. The initrd address must be offset by
KERNBASE.
Use rom_ptr mechanism to actually write to the kernel image.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
When wcycle is non zero the area is already opened for readable IO.
Avoiding the re-registration of the memarea significantly speeds up
the flash emulation. In particular for flashes connected through 8 or
16-bit buses.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@petalogix.com>
Flashes connected through an 8 bit bus cannot handle write buffers
larger than 256 bytes.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@petalogix.com>
According to Sun4M System Architecture Manual chapter 5.3.2, a limit
of 0 will not generate interrupts.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Commit 930c86820e introduced a regression to eth_send: eth_tx_desc_put
manipulates the host's tx descriptor copy before writing it back, but
two lines down the descriptor is evaluated again, leaving us with an
invalid next address if host and guest endianness differ. So this was
the actual issue commit 2e87c5b937 tried to paper over.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: malc <av1474@comtv.ru>
Commit b3a219883e uncovered that we attached the Wolfson with an I2C
address shifted left by one. Fixing this makes sound work again for
the Musicpal.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: malc <av1474@comtv.ru>
Byte swap PCI config values.
Remove old bogus PCI config mechanism so that device 0:0.0 can be probed.
This requires OpenBIOS r667.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This commit enables the use of MSI interrupts for virtqueue
notifications for ports. We use nr_ports + 1 (for control channel) msi
entries for the ports, as only the in_vq operations need an interrupt on
the guest.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This commit adds a simple chardev-based serial port. Any data the guest
sends is forwarded to the chardev and vice-versa.
Sample uses for such a device can be obtaining info from the guest like
the file systems used, apps installed, etc. for offline usage and
logged-in users, clipboard copy-paste, etc. for online usage.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The port 'id' or number is internal state between the guest kernel and
our bus implementation. This is invocation-dependent and isn't part of
the guest-host ABI.
To correcly enumerate and map ports between the host and the guest, the
'name' property is used.
Example:
-device virtserialport,name=org.qemu.port.0
This invocation will get us a char device in the guest at:
/dev/virtio-ports/org.qemu.port.0
which can be a symlink to
/dev/vport0p3
This 'name' property is exposed by the guest kernel in a sysfs
attribute:
/sys/kernel/virtio-ports/vport0p3/name
A simple udev script can pick up this name and create the symlink
mentioned above.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Via control channel messages, the guest can tell us whether a port got
opened or closed. Similarly, we can also indicate to the guest of host
port open/close events.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This commit converts the virtio-console device to create a new
virtio-serial bus that can host console and generic serial ports. The
file hosting this code is now called virtio-serial-bus.c.
The virtio console is now a very simple qdev device that sits on the
virtio-serial-bus and communicates between the bus and qemu's chardevs.
This commit also includes a few changes to the virtio backing code for
pci and s390 to spawn the virtio-serial bus.
As a result of the qdev conversion, we get rid of a lot of legacy code.
The old-style way of instantiating a virtio console using
-virtioconsole ...
is maintained, but the new, preferred way is to use
-device virtio-serial -device virtconsole,chardev=...
With this commit, multiple devices as well as multiple ports with a
single device can be supported.
For multiple ports support, each port gets an IO vq pair. Since the
guest needs to know in advance how many vqs a particular device will
need, we have to set this number as a property of the virtio-serial
device and also as a config option.
In addition, we also spawn a pair of control IO vqs. This is an internal
channel meant for guest-host communication for things like port
open/close, sending port properties over to the guest, etc.
This commit is a part of a series of other commits to get the full
implementation of multiport support. Future commits will add other
support as well as ride on the savevm version that we bump up here.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
VIRTIO_PCI_QUEUE_MAX is redefined in hw/virtio.c. Let's just keep it in
hw/virtio.h.
Also, bump up the value of the maximum allowed virtqueues to 64. This is
in preparation to allow multiple ports per virtio-console device.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Instead of using the field 'readonly' of the BlockDriverState struct for passing the request,
pass the request in the flags parameter to the function.
Signed-off-by: Naphtali Sprei <nsprei@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds compat property entries for ide-disk.ver and
scsi-disk.ver to pc-0.10 and pc-0.11. With this patch applied
the scsi and ide disks report "0.10" and "0.11" as version when
you start qemu with "-M pc-0.10" or "-M pc-0.11".
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds a new property named 'ver' to scsi-disk which allows to
specify the version which the virtual disk/cdrom should report to the
guest. By default this is the qemu version (i.e. 0.12). usage:
-drive if=none,id=disk,file=...
-device lsi
-device scsi-disk,drive=disk,bus=scsi.0,unit=0,ver=42
You can also switch the version for all scsi drives using:
-global scsi-disk.ver=42
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds a new property named 'ver' to ide-drive which allows to
specify the version which the virtual disk/cdrom should report to the
guest. By default this is the qemu version (i.e. 0.12). usage:
-drive if=none,id=disk,file=...
-device ide-drive,bus=ide.0,unit=0,drive=disk,ver=42
You can also switch the version for all ide drives using:
-global ide-drive.ver=42
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Since commit 747bbdf7 QEMU_WARN_UNUSED_RESULT is never defined as it is
conditional on a define from config-host.h which is included only later.
Include that file earlier to get the warnings back.
Reactivating it unfortunately leads to some warnings about unused qdev_init
results. These calls are changed to qdev_init_nofail to avoid build failures.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Currently we do not implement VLAN tagging for rtl8139(C+),
still data is read from ring buffer headers.
- augment unused assignment with TODO item
- cast txdw1 to void for now
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* Handling of multicast list was missing.
* Multicast all was missing.
* Promiscuous mode for multicast frames was wrong.
This patch is a step to synchronize my maintainer version
of eepro100.c (git://repo.or.cz/qemu/ar7.git) with the
version integrated in QEMU.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Handling of transmit commands is rather complex,
so about 80 lines of code were moved from function
action_command to the new function tx_command.
The two new values "tx" and "cb_address" in the
eepro100 status structure made this possible without
passing too many parameters.
In addition, the moved code was cleaned a little bit:
old comments marked with //~ were removed, C++ style
comments were replaced by C style comments, C++ like
variable declarations after code were reordered.
Simplified mode is still broken. Nor did I fix
endianess issues. Both problems will be fixed in
additional patches (which need this one).
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Don't clear interrupts on disabling, because
* Sun4M_SystemArchitecture_edited2.pdf doesn't describe
that masking or un-masking IRQ shall clear pending ones.
* Field tests also show that SPARCstation-20 doesn't
clear them.
* The patch makes Solaris 2.5.1/2.6 boot ~1500 times
faster (~20 seconds instead of ~8 hours)
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Random reading depends on having the last row/page latched and not beeing
clobbered between read and any following random reads.
Also, s->iolen must be updated when loading the io/data register with
randomly accessed flash data.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
This patch adds hardware cursor feature to SM501 graphics chip emulation,
to make the graphic console more useful for QEMU SH4 users.
Signed-off-by: Shin-ichiro KAWASAKI <kawasaki@juno.dti.ne.jp>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
As pointed out by clang size is only ever written to, but never actually
used.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
clang-analyzer points out value assigned to 'len' is not used.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Although the value stored to 'addr' is used in the enclosing expression,
the value is never actually read from 'addr'.
Probably a typo.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
pci_get_byte, pci_get_word, pci_get_long and pci_get_quad
all take a const uint8_t pointer, because they only read
the configuration data.
Their prototypes should reflect this fact.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use new way to associate ROM files to devices.
Currently, there is only a ROM file for i82559er
included in QEMU, so the patch does not add
.romfile for the other devices.
When flexible mode is fixed in eepro100, adding
more ROM files will be possible. It should be
possible to create them from pxe-i82559er.bin,
because etherboot uses the same driver for all
eepro100 devices (only PCI ids differ).
Maybe it is even possible to create a single
pxe-i8255x.bin which supports all eepro100 devices
(not supported with current etherboot).
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The numerical value was wrong (0x2800 instead of 0x0280)
which indeed did not make sense.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Mac feature bit isn't going to work as all network cards already have a
'mac' property to set the mac address. Remove it from mask and add in
get_features.
Reported-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Without this fix, guest crashes with drive=virtio.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
So '-M pc-0.10' and '-M pc-0.11' will use the fw_cfg rom load method
by default.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds a pci bus property 'rombar' which specifies whenever
the pci rom should be loaded via pci rom bar (default) or via fw_cfg.
The later can be used for compatibility with older qemu versions where
no pci rom bar is present.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch changes the way rom loading via fw_cfg is handled.
Instead of having pc_init1() call a function which passed all
roms to the firmware config we simply pass a pointer to fw_cfg
to the rom loader.
Advantage: loading roms via firmware works also for devices which
are initialized after pc_init1(), i.e. everyting added via -device.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Changes:
- make dir argument mandatory, we allways have one anyway
(vgaroms or genroms).
- check for duplicates, skip loading if found.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Changes:
- Drop extra file argument from rom_add_file().
- Drop fw_dir check in do_info_roms, we allways have a dir name.
- code style fixes.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add a new machine type for qemu 0.12.
Also fixup the 0.11 machine type: msi for virtio-blk-pci was enabled
after the 0.11 release, so turn it off in the 0.11 machine type.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Since patch ed757e140c0ada220f213036e4497315d24ca8bct, virtio will
sometimes clear all status registers on bus master disable, which loses
information such as VIRTIO_CONFIG_S_FAILED bit. This is a result of
a patch being misapplied: code uses ! instead of ~ for bit
operations as in Yan's original patch. This obviously does not make
sense.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add feature bits as properties to virtio. This makes it possible to e.g. define
machine without indirect buffer support, which is required for 0.10
compatibility, or without hardware checksum support, which is required for 0.11
compatibility. Since default values for optional features are now set by qdev,
get_features callback has been modified: it sets non-optional bits, and clears
bits not supported by host.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Rename features->guest_features. This is
what they are, avoid confusion with
host features which we also need to keep around.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
