In the very least, a change like this requires discussion on the list.
The naming convention is goofy and it causes a massive merge problem. Something
like this _must_ be presented on the list first so people can provide input
and cope with it.
This reverts commit 99a0949b72.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Up to now "select without attention" was handled the same way as
"select with attention". According to
http://www.ibiblio.org/pub/historic-linux/early-ports/Sparc/NCR/NCR53C9X.txt
select without ATN sends the CDB (Command Descriptor Block) directly,
whereas select with ATN sends one message phase byte
followed by 6, 10, or 12 command phase bytes.
The attached patch implements the behaviour described above.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
[blauwirbel@gmail.com: cleaned up formatting]
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
> ESP: Message Accepted (12)
> ESP: Transfer status (sense=0)
> ESP: read reg[5]: 0x20
> ESP: read reg[4]: 0x07
> ESP: read reg[7]: 0x02
> Extra scsi data. Fatal error.
It looks like "Message Accepted" shouldn't write a response. At least
ESP_RFLAGS must definetely be 0. With the following fix OBP goes one
step further:
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Sorry folks, but it has to be. One more of these invasive qdev patches.
We have a serious design bug in the qdev interface: device init
callbacks can't signal failure because the init() callback has no
return value. This patch fixes it.
We have already one case in-tree where this is needed:
Try -device virtio-blk-pci (without drive= specified) and watch qemu
segfault. This patch fixes it.
With usb+scsi being converted to qdev we'll get more devices where the
init callback can fail for various reasons.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch is a major overhaul of the device properties. The properties
are saved directly in the device state struct now, the linked list of
property values is gone.
Advantages:
* We don't have to maintain the list with the property values.
* The value in the property list and the value actually used by
the device can't go out of sync any more (used to happen for
the pci.devfn == -1 case) because there is only one place where
the value is stored.
* A record describing the property is required now, you can't set
random properties any more.
There are bus-specific and device-specific properties. The former
should be used for properties common to all bus drivers. Typical
use case is bus addressing, i.e. pci.devfn and i2c.address.
Properties have a PropertyInfo struct attached with name, size and
function pointers to parse and print properties. A few common property
types have PropertyInfos defined in qdev-properties.c. Drivers are free
to implement their own very special property parsers if needed.
Properties can have default values. If unset they are zero-filled.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This reverts commit 8217606e6e (and
updates later added users of qemu_register_reset), we solved the
problem it originally addressed less invasively.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The parameter is always zero except when registering the three internal
io regions (ROM, unassigned, notdirty). Remove the parameter to reduce
the API's power, thus facilitating future change.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
We have both IRQ sinks and GPIO inputs. These are in principle exactly
the same thing, so remove the former.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Add the parameter 'order' to qemu_register_reset and sort callbacks on
registration. On system reset, callbacks with lower order will be
invoked before those with higher order. Update all existing users to the
standard order 0.
Note: At least for x86, the existing users seem to assume that handlers
are called in their registration order. Therefore, the patch preserves
this property. If someone feels bored, (s)he could try to identify this
dependency and express it properly on callback registration.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When command is not DMA, TCMID and TCLO registers are not filled. Use command buffer len instead
Signed-off-by: Herve Poussineau <hpoussin@reactos.org>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5813 c046a42c-6fe2-441c-8c8c-71466251a162
According to http://www.ibiblio.org/pub/historic-linux/early-ports/Sparc/NCR/NCR53C9X.txt,
"Any bit pattern written to this register may be read back and should be identical"
Signed-off-by: Herve Poussineau <hpoussin@reactos.org>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5812 c046a42c-6fe2-441c-8c8c-71466251a162
- Fix internal fifo size (16 bytes), according to http://www.ibiblio.org/pub/historic-linux/early-ports/Sparc/NCR/NCR53C9X.txt
- Fix values of STAT_MI and STAT_MO
- Give a scsi ID to adapter, and prevent this ID to be used by devices
- Prevent fifo overrun in esp_mem_writeb
- Add a ESP_ERROR macro, and use it where appropriate
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5811 c046a42c-6fe2-441c-8c8c-71466251a162
