If booting Linux directly in the q800 machine using -kernel rather than using a
MacOS toolbox ROM, the mode control registers are never initialised,
causing macfb_mode_write() to fail to determine the current resolution after
migration. Resolve this by always setting the initial values of the mode control
registers based upon the initial macfb properties during realize.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305155530.9265-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
These fields are required in the migration stream to restore macfb state
correctly.
Note this is a migration break, but since there are upcoming incompatible changes
for the q800 machine (and migration does not even succeed without these patches)
then this is not an issue.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305155530.9265-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The MacOS toolbox ROM accesses a number of addresses between 0x0 and 0x200 during
initialisation and resolution changes. Whilst the function of many of these
registers is unknown, it is worth the minimal cost of saving these extra values as
part of migration to help future-proof the migration stream for the q800 machine
as it starts to stabilise.
Note this is a migration break, but since there are upcoming incompatible changes
for the q800 machine (and migration does not even succeed without these patches)
then this is not an issue.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305155530.9265-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The current IRQ state and IRQ mask are handled exactly the same as standard
register accesses, so store these values directly in the regs array rather
than having separate variables for them.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305155530.9265-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Currently when QEMU tries to migrate the macfb framebuffer it crashes randomly
because the opaque provided by the DeviceClass vmsd property for both devices
is set to MacfbState rather than MacfbNubusState or MacfbSysBusState as
appropriate.
Resolve the issue by adding new VMStateDescriptions for MacfbNubusState and
MacfbSysBusState which embed the existing vmstate_macfb VMStateDescription
within them using VMSTATE_STRUCT.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305155530.9265-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Debug output was always being sent to STDERR.
This has been replaced with trace events.
Signed-off-by: Carwyn Ellis <carwynellis@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220206183956.10694-2-carwynellis@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The clock field is 16-bits in EDID Detailed Timing Descriptor, but
edid_desc_timing assumed it is 32-bit. Write the 16-bit value if it fits
in 16-bit. Write DisplayID otherwise.
Signed-off-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Message-Id: <20220213021529.2248-1-akihiko.odaki@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
* Some small fixes for the qtests
* Misc header cleanups by Philippe
-----BEGIN PGP SIGNATURE-----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=/azS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/thuth-gitlab/tags/pull-request-2022-02-21' into staging
* Improve virtio-net failover test
* Some small fixes for the qtests
* Misc header cleanups by Philippe
# gpg: Signature made Mon 21 Feb 2022 11:40:37 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/thuth-gitlab/tags/pull-request-2022-02-21: (25 commits)
hw/tricore: Remove unused and incorrect header
hw/m68k/mcf: Add missing 'exec/hwaddr.h' header
exec/exec-all: Move 'qemu/log.h' include in units requiring it
softmmu/runstate: Clean headers
linux-user: Add missing "qemu/timer.h" include
target: Add missing "qemu/timer.h" include
core/ptimers: Remove unnecessary 'sysemu/cpus.h' include
exec/ramblock: Add missing includes
qtest: Add missing 'hw/qdev-core.h' include
hw/acpi/memory_hotplug: Remove unused 'hw/acpi/pc-hotplug.h' header
hw/remote: Add missing include
hw/tpm: Clean includes
scripts: Remove the old switch-timer-api script
tests/qtest: failover: migration abort test with failover off
tests/qtest: failover: test migration if the guest doesn't support failover
tests/qtest: failover: check migration with failover off
tests/qtest: failover: check missing guest feature
tests/qtest: failover: check the feature is correctly provided
tests/qtest: failover: use a macro for check_one_card()
tests/qtest: failover: clean up pathname of tests
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
More than 1k of TypeInfo instances are already marked as const. Mark the
remaining ones, too.
This commit was created with:
git grep -z -l 'static TypeInfo' -- '*.c' | \
xargs -0 sed -i 's/static TypeInfo/static const TypeInfo/'
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20220117145805.173070-2-shentey@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Many files use "qemu/log.h" declarations but neglect to include
it (they inherit it via "exec/exec-all.h"). "exec/exec-all.h" is
a core component and shouldn't be used that way. Move the
"qemu/log.h" inclusion locally to each unit requiring it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20220207082756.82600-10-f4bug@amsat.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This patchset fixes some important bugs in the hppa artist graphics driver:
- Fix artist graphics for HP-UX and Linux
- Mouse cursor fixes for HP-UX
- Fix draw_line() function on artist graphic
and it adds new qemu features for hppa:
- Allow up to 16 emulated CPUs (instead of 8)
- Add support for an emulated TOC/NMI button
A new Seabios-hppa firmware is included as well:
- Update SeaBIOS-hppa to VERSION 3
- New opt/hostid fw_cfg option to change hostid
- Add opt/console fw_cfg option to select default console
- Added 16x32 font to STI firmware
Signed-off-by: Helge Deller <deller@gmx.de>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCYfrIogAKCRD3ErUQojoP
X93ZAP9hqp/FCz/goH7Tpqce6FspHriJm6Ej2Rd7HxZWmh4bpQD/cMjY8qpcA/6r
Nx4bgRPT6kCZwwLx7v2jZ2QsA2KaZAM=
=c0qO
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/hdeller/tags/hppa-updates-pull-request' into staging
Fixes and updates for hppa target
This patchset fixes some important bugs in the hppa artist graphics driver:
- Fix artist graphics for HP-UX and Linux
- Mouse cursor fixes for HP-UX
- Fix draw_line() function on artist graphic
and it adds new qemu features for hppa:
- Allow up to 16 emulated CPUs (instead of 8)
- Add support for an emulated TOC/NMI button
A new Seabios-hppa firmware is included as well:
- Update SeaBIOS-hppa to VERSION 3
- New opt/hostid fw_cfg option to change hostid
- Add opt/console fw_cfg option to select default console
- Added 16x32 font to STI firmware
Signed-off-by: Helge Deller <deller@gmx.de>
# gpg: Signature made Wed 02 Feb 2022 18:08:34 GMT
# gpg: using EDDSA key BCE9123E1AD29F07C049BBDEF712B510A23A0F5F
# gpg: Good signature from "Helge Deller <deller@gmx.de>" [unknown]
# gpg: aka "Helge Deller <deller@kernel.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 4544 8228 2CD9 10DB EF3D 25F8 3E5F 3D04 A7A2 4603
# Subkey fingerprint: BCE9 123E 1AD2 9F07 C049 BBDE F712 B510 A23A 0F5F
* remotes/hdeller/tags/hppa-updates-pull-request:
hw/display/artist: Fix draw_line() artefacts
hw/display/artist: Mouse cursor fixes for HP-UX
hw/display/artist: rewrite vram access mode handling
hppa: Add support for an emulated TOC/NMI button.
hw/hppa: Allow up to 16 emulated CPUs
seabios-hppa: Update SeaBIOS-hppa to VERSION 3
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The draw_line() function left artefacts on the screen because it was using the
x/y variables which were incremented in the loop before. Fix it by using the
unmodified x1/x2 variables instead.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: qemu-stable@nongnu.org
Signed-off-by: Helge Deller <deller@gmx.de>
This patch fix the behaviour and positioning of the X11 mouse cursor in HP-UX.
The current code missed to subtract the offset of the CURSOR_CTRL register from
the current mouse cursor position. The HP-UX graphics driver stores in this
register the offset of the mouse graphics compared to the current cursor
position. Without this adjustment the mouse behaves strange at the screen
borders.
Additionally, depending on the HP-UX version, the mouse cursor position
in the cursor_pos register reports different values. To accommodate this
track the current min and max reported values and auto-adjust at runtime.
With this fix the mouse now behaves as expected on HP-UX 10 and 11.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: qemu-stable@nongnu.org
Signed-off-by: Helge Deller <deller@gmx.de>
When writing this code it was assumed that register 0x118000 is the
buffer access mode for color map accesses. It turned out that this
is wrong. Instead register 0x118000 sets both src and dst buffer
access mode at the same time.
This required a larger rewrite of the code. The good thing is that
both the linear framebuffer and the register based vram access can
now be combined into one function.
This makes the linux 'stifb' framebuffer work, and both HP-UX 10.20
and HP-UX 11.11 are still working.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: qemu-stable@nongnu.org
Signed-off-by: Helge Deller <deller@gmx.de>
The migration code will not look at a VMStateDescription's
minimum_version_id_old field unless that VMSD has set the
load_state_old field to something non-NULL. (The purpose of
minimum_version_id_old is to specify what migration version is needed
for the code in the function pointed to by load_state_old to be able
to handle it on incoming migration.)
We have exactly one VMSD which still has a load_state_old,
in the PPC CPU; every other VMSD which sets minimum_version_id_old
is doing so unnecessarily. Delete all the unnecessary ones.
Commit created with:
sed -i '/\.minimum_version_id_old/d' $(git grep -l '\.minimum_version_id_old')
with the one legitimate use then hand-edited back in.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
---
It missed vmstate_ppc_cpu.
spice updated the spelling (and arguments) of "attache_worker" in
0.15.0. Update QEMU to match, preventing -Wdeprecated-declarations
compilations from reporting build errors.
See also:
974692bda1
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20211215141949.3512719-3-berrange@redhat.com>
Message-Id: <20220105135009.1584676-3-alex.bennee@linaro.org>
Previously, the large modes (>1080p) that were generated by Qemu in its EDID
were all 50 Hz. If we provide them to a Guest OS and the user selects
one of these modes, then the OS by default only gets 50 FPS. This is
especially true for Windows OS. With this patch, we are now exposing a
3840x2160@60 Hz which will allow the guest OS to get 60 FPS.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Satyeshwar Singh <satyeshwar.singh@intel.com>
Message-Id: <20211116221103.27128-1-dongwon.kim@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Currently QEMU defaults to a resolution of 1024x768 when exposing EDID
info to the guest OS. The EDID default info is important as this will
influence what resolution many guest OS will configure the screen with
on boot. It can also potentially influence what resolution the firmware
will configure the screen with, though until very recently EDK2 would
not handle EDID info.
One important thing to bear in mind is that the default graphics card
driver provided by Windows will leave the display set to whatever
resolution was enabled by the firmware on boot. Even if sufficient
VRAM is available, the resolution can't be changed without installing
new drivers. IOW, the default resolution choice is quite important
for usability of Windows.
Modern real world monitor hardware for desktop/laptop has supported
resolutions higher than 1024x768 for a long time now, perhaps as long
as 15+ years. There are quite a wide variety of native resolutions in
use today, however, and in wide screen form factors the height may not
be all that tall.
None the less, it is considered that there is scope for making the
QEMU default resolution slightly larger.
In considering what possible new default could be suitable, choices
considered were 1280x720 (720p), 1280x800 (WXGA) and 1280x1024 (SXGA).
In many ways, vertical space is the most important, and so 720p was
discarded due to loosing vertical space, despite being 25% wider.
The SXGA resolution would be good, but when taking into account
window titlebars/toolbars and window manager desktop UI, this might
be a little too tall for some users to fit the guest on their physical
montior.
This patch thus suggests a modest change to 1280x800 (WXGA). This
only consumes 1 MB per colour channel, allowing double buffered
framebuffer in 8 MB of VRAM. Width wise this is 25% larger than
QEMU's current default, but height wise this only adds 5%, so the
difference isn't massive on the QEMU side.
Overall there doesn't appear to be a compelling reason to stick
with 1024x768 resolution.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20211129140508.1745130-1-berrange@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
vga_mmio_init() is used only one time and not very helpful,
inline and remove it.
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20211206224528.563588-5-f4bug@amsat.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Introduce TYPE_VGA_MMIO, a sysbus device.
While there is no change in the vga_mmio_init()
interface, this is a migration compatibility break
of the MIPS Acer Pica 61 Jazz machine (pica61).
Suggested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20211206224528.563588-4-f4bug@amsat.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Inline vga_mm_init() in vga_mmio_init() to simplify the
next patch review. Kind of.
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20211206224528.563588-3-f4bug@amsat.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
There is no ISA bus part in the MMIO VGA device, so rename:
* hw/display/vga-isa-mm.c -> hw/display/vga-mmio.c
* CONFIG_VGA_ISA_MM -> CONFIG_VGA_MMIO
* ISAVGAMMState -> VGAMmioState
* isa_vga_mm_init() -> vga_mmio_init()
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20211206224528.563588-2-f4bug@amsat.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The macfb VRAM memory region was configured with coalescing rather than dirty
memory logging enabled, causing some areas of the screen not to redraw after
a full screen update.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Fixes: 8ac919a065 ("hw/m68k: add Nubus macfb video card")
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220108164147.30813-1-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
To support configure interrupt for vhost-vdpa
Introduce VIRTIO_CONFIG_IRQ_IDX -1 as configure interrupt's queue index,
Then we can reuse the functions guest_notifier_mask and guest_notifier_pending.
Add the check of queue index in these drivers, if the driver does not support
configure interrupt, the function will just return
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20211104164827.21911-2-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Let devices specify transaction attributes when calling
dma_memory_map().
Patch created mechanically using spatch with this script:
@@
expression E1, E2, E3, E4;
@@
- dma_memory_map(E1, E2, E3, E4)
+ dma_memory_map(E1, E2, E3, E4, MEMTXATTRS_UNSPECIFIED)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20211223115554.3155328-7-philmd@redhat.com>
GraphicHw.gl_flushed was introduced to notify the
device (vhost-user-gpu) that the GL resources (the display scanout) are
no longer needed.
It was decoupled from QEMU own gl-blocking mechanism, but that
difference isn't helping. Instead, we can reuse QEMU gl-blocking and
notify virtio_gpu_gl_flushed() when unblocking (to unlock
vhost-user-gpu).
An extra block/unblock is added arount dpy_gl_update() so existing
backends that don't block will have the flush event handled. It will
also help when there are no backends associated.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
It's part of Linux headers for a while now.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Currently, virgl initialization error is silent. Make it verbose instead.
(this is likely going to bug later on, as the device isn't fully
initialized)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This reverts commit 7852a77f59.
The check is bogus as it ends up finding itself and falling over.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/733
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20211206095209.2332376-1-alex.bennee@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Rewrite the function using g_string_append_printf() rather than
g_strdup_printf()/g_strconcat().
Fixes: df8abbbadf ("macfb: add common monitor modes supported by the MacOS toolbox ROM")
Cc: mark.cave-ayland@ilande.co.uk
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20211105165254.3544369-1-laurent@vivier.eu>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
When guest is running Linux/X11 with extended multiple displays mode enabled,
the guest shares one scanout resource each time containing whole surface
rather than sharing individual display output separately. This extended frame
is properly splited and rendered on the corresponding scanout surfaces but
not in case of blob-resource (zero copy).
This code change lets the qemu split this one large surface data into multiple
in case of blob-resource as well so that each sub frame then can be blitted
properly to each scanout.
v2: resizing qemu console in virtio_gpu_update_dmabuf to scanout's width and
height
v3: updating stub function of virtio_gpu_update_dmabuf to match the type
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Dongwon Kim <dongwon.kim@intel.com>
Message-Id: <20211104065153.28897-5-dongwon.kim@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Any extra draw call for the same blob resource representing guest scanout
before the previous drawing is not finished can break synchronous draw
sequence. To prevent this, drawing is now done only once for each draw
submission (when draw_submitted == true).
v2:
- removed mutex
- updated commit msg
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Dongwon Kim <dongwon.kim@intel.com>
Message-Id: <20210924225105.24930-1-dongwon.kim@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The MacOS driver expects a 60.15Hz vertical blank interrupt to be generated by
the framebuffer which in turn schedules the mouse driver via the Vertical Retrace
Manager.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-13-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
According to Apple Technical Note HW26: "Macintosh Quadra Built-In Video" the
in-built framebuffer encodes each 24-bit pixel into 4 bytes. Adjust the 24-bit
RGB pixel encoding accordingly which agrees with the encoding expected by MacOS
when changing into 24-bit colour mode.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-12-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The MacOS driver expects the RGB values for the pixel to be in entries 0 and 1
of the colour palette.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The monitor modes table is found by experimenting with the Monitors Control
Panel in MacOS and analysing the reads/writes. From this it can be found that
the mode is controlled by writes to the DAFB_MODE_CTRL1 and DAFB_MODE_CTRL2
registers.
Implement the first block of DAFB registers as a register array including the
existing sense register, the newly discovered control registers above, and also
the DAFB_MODE_VADDR1 and DAFB_MODE_VADDR2 registers which are used by NetBSD to
determine the current video mode.
These experiments also show that the offset of the start of video RAM and the
stride can change depending upon the monitor mode, so update macfb_draw_graphic()
and both the BI_MAC_VADDR and BI_MAC_VROW bootinfo for the q800 machine
accordingly.
Finally update macfb_common_realize() so that only the resolution and depth
supported by the display type can be specified on the command line, and add an
error hint showing the list of supported resolutions and depths if the user tries
to specify an invalid display mode.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Since the available resolutions and colour depths are determined by the attached
display type, add a qdev property to allow the display type to be specified.
The main resolutions of interest are high resolution 1152x870 with 8-bit colour
and SVGA resolution up to 800x600 with 24-bit colour so update the q800 machine
to allow high resolution mode if specified and otherwise fall back to SVGA.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The MacOS toolbox ROM uses the monitor sense to detect the display type and then
offer a fixed set of resolutions and colour depths accordingly. Implement the
monitor sense using information found in Apple Technical Note HW26: "Macintosh
Quadra Built-In Video" along with some local experiments.
Since the default configuration is 640 x 480 with 8-bit colour then hardcode
the sense register to return MACFB_DISPLAY_VGA for now.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Currently macfb_common_realize() defines the framebuffer RAM memory region as
being non-migrateable but then immediately registers it for migration. Replace
memory_region_init_ram_nomigrate() with memory_region_init_ram() which is clearer
and does exactly the same thing.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The palette_current index counter has a maximum size of 256 * 3 to cover a full
color palette of 256 RGB entries. Linux assumes that the palette_current index
wraps back around to zero after writing 256 RGB entries so ensure that
palette_current is reset at this point to prevent data corruption within
MacfbState.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
During realize memory_region_init_ram_nomigrate() is used to initialise the RAM
memory region used for the framebuffer but the owner object reference is
incorrect since MacFbState is a typedef and not a QOM type.
Change the memory region owner to be the corresponding DeviceState to fix the
issue and prevent random crashes during macfb_common_realize().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Fixes: 8ac919a065 ("hw/m68k: add Nubus macfb video card")
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
As per the current Error API best practices, change macfb_commom_realize() to return
a boolean indicating success to reduce errp boiler-plate handling code. Note that
memory_region_init_ram_nomigrate() is also updated to use &error_abort to indicate
a non-recoverable error, matching the behaviour recommended after similar
discussions on memory API failures for the recent nubus changes.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Make sure any errors that occur within the macfb realize chain are detected
and handled correctly to prevent crashes and to ensure that error messages are
reported back to the user.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The macfb device is an on-board framebuffer and so is initialised by the
system declaration ROM included within the MacOS toolbox ROM.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210924073808.1041-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Adding this callback provides a way to resume the processing of
cmds in fenceq and cmdq that were not processed because the UI
was waiting on a fence and blocked cmd processing.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210914211837.3229977-6-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Create sync objects and fences only for dmabufs that are blobs. Once a
fence is created (after glFlush) and is signalled,
graphic_hw_gl_flushed() will be called and virtio-gpu cmd processing
will be resumed.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210914211837.3229977-4-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>