The contents of the FIFO should only be copied to cmdfifo for ESP commands that
are sending data to the SCSI bus, which are the SEL_* commands and the TI
command. Otherwise any incoming data should be held in the FIFO as normal.
This fixes booting of really old 32-bit SPARC Linux kernels such as Aurelien's
debian_etch_sparc_small.qcow2 test image.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-77-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The ESP_RSEQ logic is scattered in a few places throughout the ESP state machine
which is mainly because the ESP_RSEQ register isn't always reset when executing
an ESP select command. Once this is done, the ESP_RSEQ register only needs to be
updated at the point where the sequencer command completes.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-76-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Certain versions of MacOS send the first 5 bytes of the CDB using DMA and then
send the last byte of the CDB by writing to the FIFO. Update the non-DMA state
machine to detect the end of the CDB and execute the SCSI command using similar
logic as that which already exists for transferring the remainder of the CDB
using the ESP TI command.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-75-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The latest state machines can handle mixing DMA and non-DMA FIFO access for all
SCSI phases except DATA IN and DATA OUT. For DATA IN and DATA OUT phases, the
transfer is complete when TC == 0 and the updated logic will now handle TC
underflow correctly, which makes it just about impossible to manually manipulate
the FIFO during a DMA transfer.
Remove the restriction on FIFO read access when DMA memory routines are defined
which also allows the NeXTCube machine to pass its self-test.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-74-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Detect the case where the guest underflows TC by requesting a DMA transfer which
is larger than the available data. If this case is detected, immediately
complete the SCSI request and handle any remaining FIFO accesses in the STATUS
phase by raising INTR_BS once the FIFO is below the threshold.
Note that handling the premature SCSI bus phase change in the case of TC
underflow fixes booting EMILE on m68k once again.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-73-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
According to the documentation ESP_RSTAT is cleared (except the STAT_TC bit)
when ESP_RINTR is read. This should not include the SCSI bus phase bits which
are currently live from the SCSI bus, otherwise the current SCSI phase is lost
when clearing an end-of-transfer interrupt.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-72-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Both esp_raise_irq() and esp_lower_irq() check the STAT_INT bit in ESP_RSTAT
to ensure that the IRQ is raised or lowered if its state changes. When reading
ESP_RINTR, esp_lower_irq() was being called *after* ESP_RSTAT had been
cleared meaning that STAT_INT was already clear, and so if STAT_INT was
asserted beforehand then the esp_lower_irq() would have no effect.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-71-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The end of command sequences for the ICCS command are currently different
between the DMA and non-DMA versions, and also different from the description
in the datasheet.
Update the sequence so that only INTR_FC is asserted in both cases, and keep
all the logic in esp_do_dma() and esp_do_nodma() rather than having some of
it within esp_run_cmd().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-70-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This moves the remaining non-DMA STATUS and MESSAGE IN phase logic from
write_response() to esp_do_nodma(). Note that we can also now drop the extra
fifo_reset() which is no longer required.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-69-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Now that the esp_do_nodma() state machine correctly handles incoming FIFO
data, all remaining users of get_cmd() can be replaced with esp_do_nodma()
and the get_cmd() function removed completely.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-68-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Currently any write to the ESP FIFO in the MESSAGE OUT or COMMAND phases will
manually raise the bus service interrupt. Instead of duplicating the interrupt
logic in esp_reg_write(), update esp_do_nodma() to correctly process incoming
FIFO data during the MESSAGE OUT and COMMAND phases. Part of this change is to
call esp_nodma_ti_dataout() from handle_ti() to ensure that the DATA OUT phase
FIFO transfer only occurs when executing a non-DMA TI command instead of for
each byte entering the FIFO.
One slight complication is that NextSTEP uses multiple TI commands to transfer
the CDB one byte at a time (as opposed to loading the FIFO and using a single
TI command), so it is necessary to determine the expected length of the SCSI
CDB being received. This is handled by the introduction of a new
esp_cdb_length() function which returns the expected SCSI CDB length based
upon the first command byte.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-67-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This is to allow the logic to be moved during the next commit.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-66-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
In the case where a SCSI command with a DATA IN phase has been issued, the host
may preload the FIFO with unaligned bytes before issuing the main DMA transfer.
When accumulating data in the FIFO don't raise the INTR_BS interrupt until the
TI command is issued, otherwise the unexpected interrupt can confuse the host.
In particular this is needed to prevent the MacOS Disk Utility from failing
when switching non-DMA transfers to use esp_do_nodma().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-65-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
According to the datasheet the previous ESP command remains in the ESP_CMD
register, which caused a problem when consecutive TI commands were issued as
it becomes impossible for the state machine to know when the first TI
command finishes.
This was the original reason for introducing the ti_cmd field which kept
track of the last written command for this purpose. However closer reading
of the datasheet shows that a TI command that terminates due to a change of
SCSI target phase resets the ESP_CMD register to zero which solves this
problem.
Now that this has been fixed in the previous commit, remove the unneeded
ti_cmd field and access the ESP_CMD register directly instead. Bump the
vmstate_esp version to indicate that the ti_cmd field is no longer included.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-64-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This is the behaviour documented in the datasheet and allows the state machine
to correctly process multiple consecutive TI commands.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-63-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Whilst the FIFO is used a storage buffer for both DMA and non-DMA requests, the
loading and unloading is managed directly issuing commands to the ESP. As a
result there is no need to manually invoke the non-DMA command handler.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-62-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This brings DATA OUT transfers in line with DATA IN transfers by ensuring that
the guest visible function complete interrupt is only set once the SCSI layer
has returned.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-61-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The handling of the INTR_FC and INTR_BS bits is different depending upon the
last command executed by the ESP. Note that currently INTR_FC is managed
elsewhere, but that will change soon.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-60-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The handling of the INTR_FC and INTR_BS bits is different depending upon the
last command executed by the ESP. Note that currently INTR_FC is managed
elsewhere, but that will change soon.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-59-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This field is currently used to handle deferred interrupts for the DATA IN phase
but the code will soon be updated to do the same for the DATA OUT phase.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-58-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Note that this is a migration break for the q800 machine because the extra PDMA
information is no longer included.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-57-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
There is now only a single implementation contained within esp_do_dma() so
call it directly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-56-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The special logic in write_response_pdma_cb() is now no longer required since
esp_do_dma() can be used as a direct replacement.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-55-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Now that the DMA logic is identical between do_dma_pdma_cb() and esp_do_dma()
we can replace do_dma_pdma_cb() with esp_do_dma().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-54-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The special logic in satn_stop_pdma_cb() is now no longer required since
esp_do_dma() can be used as a direct replacement.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-53-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This can now be done using the existing logic in esp_do_dma() and do_dma_pdma_cb().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-52-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The existing check for TC == 0 is only valid during a TI command.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-51-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The special logic in satn_pdma_cb() is now no longer required since esp_do_dma()
can be used as a direct replacement.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-50-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This makes it clearer that ATN is asserted until the end of the next TI command
in the MESSAGE OUT phase.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-49-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This makes it clearer that ATN is asserted until the end of the next TI command
in the MESSAGE OUT phase.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-48-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This makes it clearer that ATN is asserted until the end of the next TI command
in the MESSAGE OUT phase.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-47-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Now that the accumulation of the CDB is handled by SCSI phase, there is no need
for a separate variable to control it.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-46-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Currently do_cmd is used to determine whether MESSAGE OUT and COMMAND phase data
is being accumulated in cmdfifo. Update esp_do_dma() to check directly for these
two SCSI phases instead.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-45-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Currently do_cmd is used to determine whether MESSAGE OUT and COMMAND phase data
is being accumulated in cmdfifo. Update esp_do_dma() to check directly for these
two SCSI phases instead.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-44-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Currently do_cmd is used to determine whether MESSAGE OUT and COMMAND phase data
is being accumulated in cmdfifo. Update esp_do_dma() to check directly for these
two SCSI phases instead.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-43-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Currently do_cmd is used to determine whether MESSAGE OUT and COMMAND phase data
is being accumulated in cmdfifo. Update esp_do_dma() to check directly for these
two SCSI phases instead.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-42-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Currently only the DATA IN and DATA OUT phases are supported.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-41-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Currently only the DATA IN and DATA OUT phases are supported.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-40-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Currently only the DATA IN and DATA OUT phases are supported.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-39-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Make use of this new function in all places where the SCSI phase bits are
manually masked from the ESP_RSTAT register.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240112125420.514425-38-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This can now be handled by the existing do_dma_pdma_cb() function.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-37-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Now it is possible to move the end of SCSI transfer check to after the TC
adjustment in do_dma_pdma_cb() when transferring data from the device
without triggering an assert() in the SCSI code. This brings this check in
line with all the others in esp_do_dma() and do_dma_pdma_cb().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-36-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
In the PDMA case the last transfer from the device to the FIFO has occurred
(async_len is zero) but esp_do_dma() is still being called to drain the
remaining FIFO contents.
The additional non-zero transfer check ensures that we still defer the SCSI
layer in the case where we are waiting for data for a TI command or a DMA
enable signal.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-35-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This is so that PDMA transfers can be performend by esp_do_dma() as well as
do_dma_pdma_cb().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-34-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This is so that PDMA transfers can be performend by esp_do_dma() as well as
do_dma_pdma_cb().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-33-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This is because a single DMA request can be transferred using multiple TI
commands, and so a TC equal to zero may not represent the completion of
the SCSI DMA command.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-32-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This helps simplify the existing implementation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-31-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
There are two cases here: the first is when the TI command underflows, in which
case we raise INTR_BS to indicate an early change of phase, and the second is
when the TI command overflows because the host requested a transfer for more
data than is available. In the latter case force TC to zero so that the TI
completion logic executes correctly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-30-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Ensure that the async_len checks for requesting data from the SCSI layer and
the TC == 0 checks to detect the end of the DMA transfer are consistent in both
do_dma_pdma_cb() and esp_do_dma(). In particular this involves adding the check
to see if the FIFO is at its low threshold since PDMA and mixed DMA and non-DMA
requests can leave data remaining in the FIFO.
At the same time update all the comments so that they are also consistent between
all similar code paths.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-29-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Since esp_dma_done() is called in both cases, and ti_size cannot be zero
(otherwise esp_command_complete() would have been called instead), replace
the conditional logic with a single call to esp_dma_done().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-28-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The following ti_cmd checks ensure that only DMA and non-DMA TI commmands will
can call into the esp_do_dma() and esp_do_nodma() callbacks.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-27-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
With the latest changes this condition cannot occur anymore and so the logic
can be completely removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-26-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Now that the TC is updated for each PDMA access (rather than once the FIFO is
full) there is no need to adjust the TC at start of each DMA transfer if the
FIFO is not empty.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-25-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
In the case when more data is requested from the SCSI layer during a DMA data
transfer from a device, don't immediately fall through to the TC check logic.
Otherwise when TC is zero INTR_BS will be raised immediately rather than when
the next set of SCSI data is ready.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-24-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Rather than wait for the FIFO to fill up before calling the PDMA callback, push
that logic directly into the from_device logic in do_dma_pdma_cb().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-23-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Ensure that esp_dma_done() is only called when TC is zero, which is currently
always the case for DMA transfers.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-22-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
No change to the condition itself, other than to clarify that esp_dma_done()
must be called when TC is zero.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-21-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The TI end of transfer interrupt only occurs when the TC reaches zero and is
not related to the SCSI layer transfer.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-20-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The internal state of the ESP sequencer is not affected when raising an interrupt
to indicate the end of a DMA transfer.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-19-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
There is no need to manually reset these values as the ESP emulation now
correctly handles them within its existing logic.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-18-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This workaround is no longer required with the current code and so can be
removed.
[Note: whilst MacOS itself can boot correctly, removing this hack prevents
a bootable EMILE CDROM from working. This is caused by a separate bug which
will be fixed by a subsequent patch]
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-17-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Following on from the recent changes to when the TC is updated, it is now
possible to remove another set of manual STAT_TC updates so that its state
is now managed within esp_set_tc().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-16-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This function is used to set the current SCSI bus phase in the ESP_RSTAT register
without affecting any of flag bits.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-15-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This is to ensure that STAT_TC is triggered during the right parts of the
transfer when it is controlled exclusively by the TC.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-14-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Instead accumulate in the real FIFO as done in real hardware, and then transfer
to cmdfifo when we're ready to process the MESSAGE OUT and COMMAND phase data.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-13-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The do_cmd variable is only set for the MESSAGE OUT and COMMAND phases i.e.
those which involve transfers from the host to the SCSI bus, and so the unused
case can be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-12-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The ultimate aim is to for esp_do_dma() behaviour to be determined by the SCSI
bus phase, in which case it is necessary to have separate to/from device paths.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Invert the logic so that the end of DMA transfer check becomes one that checks
for TC == 0 in the from device path in do_dma_pdma_cb().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This helps to simplify esp_reg_write() and potentially allows for a 2-level
deep FIFO to be implemented in future.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This should be exclusively managed by esp_set_tc() rather than being manually
set in multiple places. Start by removing the occurrences exclusive to PDMA
and command completion which are those that can be currently removed without
affecting any test images.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This flag is set once the transfer counter counts down to zero.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Since the DREQ value depends upon the result of the selection process, add a
workaround to each esp_select() to manually assert DREQ durring the MESSAGE OUT
and COMMAND phases.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The FIFO contents should not be affected by performing SCSI target selection.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The fifo8_pop_buf() function returns a pointer to the FIFO buffer up to the
specified length. Since the FIFO buffer is modelled as an array then once
the FIFO wraps around, only the continuous portion of the buffer can be
returned.
In future the use of continuous and unaligned accesses will advance the
internal FIFO head pointer, so modify esp_fifo_pop_buf() to ensure that
any wraparound content is also returned up to the requested length.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Since get_cmd() can be called multiple times during a mixed FIFO/DMA request,
move the existing request cancel check into esp_select() which always occurs
at the start of new SCSI request.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The FIFO contents should not be affected if the target selection fails.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Some enhancements and fixes for the hppa target.
The major change is, that this patchset adds a new SeaBIOS-hppa firmware
which is built as 32- and 64-bit firmware.
The new 64-bit firmware is necessary to fully support 64-bit operating systems
(HP-UX, Linux, NetBSD,...).
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCZcquAQAKCRD3ErUQojoP
X9pjAQCVsWyuYlGCW2paIGVWKV0vsOpwetUrbhRtFUZGqZxb4AD9FbMsXRcCN/oq
CotBPY/a8MEzIQcwYl5QbcI5nNW4ygs=
=RA0B
-----END PGP SIGNATURE-----
Merge tag 'hppa64-pull-request' of https://github.com/hdeller/qemu-hppa into staging
target/hppa: Enhancements and fixes
Some enhancements and fixes for the hppa target.
The major change is, that this patchset adds a new SeaBIOS-hppa firmware
which is built as 32- and 64-bit firmware.
The new 64-bit firmware is necessary to fully support 64-bit operating systems
(HP-UX, Linux, NetBSD,...).
# -----BEGIN PGP SIGNATURE-----
#
# iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCZcquAQAKCRD3ErUQojoP
# X9pjAQCVsWyuYlGCW2paIGVWKV0vsOpwetUrbhRtFUZGqZxb4AD9FbMsXRcCN/oq
# CotBPY/a8MEzIQcwYl5QbcI5nNW4ygs=
# =RA0B
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 12 Feb 2024 23:47:13 GMT
# gpg: using EDDSA key BCE9123E1AD29F07C049BBDEF712B510A23A0F5F
# gpg: Good signature from "Helge Deller <deller@gmx.de>" [unknown]
# gpg: aka "Helge Deller <deller@kernel.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 4544 8228 2CD9 10DB EF3D 25F8 3E5F 3D04 A7A2 4603
# Subkey fingerprint: BCE9 123E 1AD2 9F07 C049 BBDE F712 B510 A23A 0F5F
* tag 'hppa64-pull-request' of https://github.com/hdeller/qemu-hppa:
hw/hppa/machine: Load 64-bit firmware on 64-bit machines
target/hppa: Update SeaBIOS-hppa to version 16
hw/net/tulip: add chip status register values
target/hppa: PDC_BTLB_INFO uses 32-bit ints
target/hppa: Allow read-access to PSW with rsm 0,reg instruction
lasi: Add reset I/O ports for LASI audio and FDC
target/hppa: Implement do_transaction_failed handler for I/O errors
lasi: allow access to LAN MAC address registers
hw/pci-host/astro: Implement Hard Fail and Soft Fail mode
hw/pci-host/astro: Avoid aborting on access failure
target/hppa: Add "diag 0x101" for console output support
disas/hppa: Add disassembly for qemu specific instructions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
qemu_smbios_type8_opts did not have the list terminator and that
resulted in out-of-bound memory access. It also needs to have an element
for the type option.
Cc: qemu-stable@nongnu.org
Fixes: fd8caa253c ("hw/smbios: support for type 8 (port connector)")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
qemu_smbios_type11_opts did not have the list terminator and that
resulted in out-of-bound memory access. It also needs to have an element
for the type option.
Cc: qemu-stable@nongnu.org
Fixes: 2d6dcbf93f ("smbios: support setting OEM strings table")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Use device_class_set_parent_realize() to set parent realize() directly.
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Use device_class_set_parent_realize() to set parent realize() directly.
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Use device_class_set_parent_realize() to set parent realize() directly.
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Use device_class_set_parent_realize() to set parent realize() directly.
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Load the 64-bit SeaBIOS-hppa firmware by default when running on a 64-bit
machine. This will enable us to later support more than 4GB of RAM and is
required that the OS (or PALO bootloader) will start or install a 64-bit kernel
instead of a 32-bit kernel.
Note that SeaBIOS-hppa v16 provides the "-fw_cfg opt/OS64,string=3" option with
which the user can control what the firmware shall report back to the OS:
Support of 32-bit OS, support of a 64-bit OS, or support for both (default).
Wrap firmware loading inside !qtest_enabled() to avoid this warning with
qtest: "qemu-system-hppa: no firmware provided".
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Netbsd isn't able to detect a link on the emulated tulip card. That's
because netbsd reads the Chip Status Register of the Phy (address
0x14). The default phy data in the qemu tulip driver is all zero,
which means no link is established and autonegotation isn't complete.
Therefore set the register to 0x3b40, which means:
Link is up, Autonegotation complete, Full Duplex, 100MBit/s Link
speed.
Also clear the mask because this register is read only.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Helge Deller <deller@gmx.de>
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Linux writes zeroes at bootup into the default ports for LASI audio and
LASI floppy controller to reset those devices. Allow writing to those
registers to avoid HPMCs.
Signed-off-by: Helge Deller <deller@gmx.de>
Firmware and qemu reads and writes the MAC address for the LASI LAN via
registers in LASI. Allow those accesses and return zero even if LASI
LAN isn't enabled to avoid HPMCs (=crashes).
Signed-off-by: Helge Deller <deller@gmx.de>
The Astro/Elroy chip can work in either Hard-Fail or Soft-Fail mode.
Hard fail means the system bus will send an HPMC (=crash) to the
processor, soft fail means the system bus will ignore timeouts of
MMIO-reads or MMIO-writes and return -1ULL.
The HF mode is controlled by a bit in the status register and is usually
programmed by the OS. Return the corresponing values based on the current
value of that bit.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Instead of stopping the emulation, report a MEMTX_DECODE_ERROR if the OS
tries to access non-existent registers.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
* Check for 'A' extension on all atomic instructions
* Add support for 'B' extension
* Internally deprecate riscv_cpu_options
* Implement optional CSR mcontext of debug Sdtrig extension
* Internally add cpu->cfg.vlenb and remove cpu->cfg.vlen
* Support vlenb and vregs[] in KVM
* RISC-V gdbstub and TCG plugin improvements
* Remove vxrm and vxsat from FCSR
* Use RISCVException as return type for all csr ops
* Use g_autofree more and fix a memory leak
* Add support for Zaamo and Zalrsc
* Support new isa extension detection devicetree properties
* SMBIOS support for RISC-V virt machine
* Enable xtheadsync under user mode
* Add rv32i,rv32e and rv64e CPUs
-----BEGIN PGP SIGNATURE-----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=yuRM
-----END PGP SIGNATURE-----
Merge tag 'pull-riscv-to-apply-20240209' of https://github.com/alistair23/qemu into staging
RISC-V PR for 9.0
* Check for 'A' extension on all atomic instructions
* Add support for 'B' extension
* Internally deprecate riscv_cpu_options
* Implement optional CSR mcontext of debug Sdtrig extension
* Internally add cpu->cfg.vlenb and remove cpu->cfg.vlen
* Support vlenb and vregs[] in KVM
* RISC-V gdbstub and TCG plugin improvements
* Remove vxrm and vxsat from FCSR
* Use RISCVException as return type for all csr ops
* Use g_autofree more and fix a memory leak
* Add support for Zaamo and Zalrsc
* Support new isa extension detection devicetree properties
* SMBIOS support for RISC-V virt machine
* Enable xtheadsync under user mode
* Add rv32i,rv32e and rv64e CPUs
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEaukCtqfKh31tZZKWr3yVEwxTgBMFAmXGBRAACgkQr3yVEwxT
# gBPqVA//etMiwP8+lQb2E4pw+QwBIzpm3qFyBlqgSCFrekj1u2kYNd4CH3CKurWE
# ysoQ6OAMeb0MUbRHdjrejjzD/wOg7JNA9h7ynM1VbupveBrJY3GWC6qQWSG+A1j/
# LSgmr/dDya74chDxjxa+7ld3xqloHi5OtdGaeORfdPXl7mjCCKKCoSKYCex1ykup
# uuB7bsjeWeWEbuUsntmeuHJLZJuhpnbuZJmp17tEo+3vWXqjxV00Lik+XMwh3gua
# KOLiAqHjGr2NEhA3Mg1JLcQ+6JLTDM9ugZpQeNGQwMkfuB/RAU7jO/1Di3flbadF
# 8l2xOHu3mydDbfdxTGZNJjcIrMTX/YEewAYZLRYpNsyPOMntgq8HEegwCdWGvK7C
# M5Tc59MNSuBt+zkZkHd21qLYusa2ThP4YT/schh7IA+2F1TSKdhlptEzi2oebIc7
# ilLSgZ9Of72QlAH2OPJNSAL9Nbc06MHEM0JiHIJa5u+XdcVRhZus5h1YIOKXisqF
# YPP22RnI5Jj5d5csa/0ONAZGFh5SRMTJtpjKoKSkzoYJWDjCQ2MiUAOmLscchMZd
# wbK0vjeRf6kRG4U4z7nTmHS9kzH8RXUZDecVcOITuMpKih9LhUiCZ+xPunFYPycJ
# WNFa9/pENcCXJweXvtk4NHwx933rX56678lF6KY2hwUwwaiBOv4=
# =yuRM
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 09 Feb 2024 10:57:20 GMT
# gpg: using RSA key 6AE902B6A7CA877D6D659296AF7C95130C538013
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6AE9 02B6 A7CA 877D 6D65 9296 AF7C 9513 0C53 8013
* tag 'pull-riscv-to-apply-20240209' of https://github.com/alistair23/qemu: (61 commits)
target/riscv: add rv32i, rv32e and rv64e CPUs
target/riscv/cpu.c: add riscv_bare_cpu_init()
target/riscv: Enable xtheadsync under user mode
qemu-options: enable -smbios option on RISC-V
target/riscv: SMBIOS support for RISC-V virt machine
smbios: function to set default processor family
smbios: add processor-family option
target/riscv: support new isa extension detection devicetree properties
target/riscv: use misa_mxl_max to populate isa string rather than TARGET_LONG_BITS
target/riscv: Expose Zaamo and Zalrsc extensions
target/riscv: Check 'A' and split extensions for atomic instructions
target/riscv: Add Zaamo and Zalrsc extension infrastructure
hw/riscv/virt.c: use g_autofree in create_fdt_*
hw/riscv/virt.c: use g_autofree in virt_machine_init()
hw/riscv/virt.c: use g_autofree in create_fdt_virtio()
hw/riscv/virt.c: use g_autofree in create_fdt_sockets()
hw/riscv/virt.c: use g_autofree in create_fdt_socket_cpus()
hw/riscv/numa.c: use g_autofree in socket_fdt_write_distance_matrix()
hw/riscv/virt-acpi-build.c: fix leak in build_rhct()
target/riscv: Use RISCVException as return type for all csr ops
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Generate SMBIOS tables for the RISC-V mach-virt.
Add CONFIG_SMBIOS=y to the RISC-V default config.
Set the default processor family in the type 4 table.
The implementation is based on the corresponding ARM and Loongson code.
With the patch the following firmware tables are provided:
etc/smbios/smbios-anchor
etc/smbios/smbios-tables
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20240123184229.10415-4-heinrich.schuchardt@canonical.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Provide a function to set the default processor family.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20240123184229.10415-3-heinrich.schuchardt@canonical.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
For RISC-V the SMBIOS standard requires specific values of the processor
family value depending on the bitness of the CPU.
Add a processor-family option for SMBIOS table 4.
The value of processor-family may exceed 255 and therefore must be provided
in the Processor Family 2 field. Set the Processor Family field to 0xFE
which signals that the Processor Family 2 is used.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20240123184229.10415-2-heinrich.schuchardt@canonical.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
A few months ago I submitted a patch to various lists, deprecating
"riscv,isa" with a lengthy commit message [0] that is now commit
aeb71e42caae ("dt-bindings: riscv: deprecate riscv,isa") in the Linux
kernel tree. Primarily, the goal was to replace "riscv,isa" with a new
set of properties that allowed for strictly defining the meaning of
various extensions, where "riscv,isa" was tied to whatever definitions
inflicted upon us by the ISA manual, which have seen some variance over
time.
Two new properties were introduced: "riscv,isa-base" and
"riscv,isa-extensions". The former is a simple string to communicate the
base ISA implemented by a hart and the latter an array of strings used
to communicate the set of ISA extensions supported, per the definitions
of each substring in extensions.yaml [1]. A beneficial side effect was
also the ability to define vendor extensions in a more "official" way,
as the ISA manual and other RVI specifications only covered the format
for vendor extensions in the ISA string, but not the meaning of vendor
extensions, for obvious reasons.
Add support for setting these two new properties in the devicetrees for
the various devicetree platforms supported by QEMU for RISC-V. The Linux
kernel already supports parsing ISA extensions from these new
properties, and documenting them in the dt-binding is a requirement for
new extension detection being added to the kernel.
A side effect of the implementation is that the meaning for elements in
"riscv,isa" and in "riscv,isa-extensions" are now tied together as they
are constructed from the same source. The same applies to the ISA string
provided in ACPI tables, but there does not appear to be any strict
definitions of meanings in ACPI land either.
Link: https://lore.kernel.org/qemu-riscv/20230702-eats-scorebook-c951f170d29f@spud/ [0]
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/riscv/extensions.yaml [1]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240124-unvarying-foothold-9dde2aaf95d4@spud>
[ Changes by AF:
- Rebase on recent changes
]
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We have a lot of cases where a char or an uint32_t pointer is used once
to alloc a string/array, read/written during the function, and then
g_free() at the end. There's no pointer re-use - a single alloc, a
single g_free().
Use 'g_autofree' to avoid the g_free() calls.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240122221529.86562-8-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Move 'soc_name' to the loop, and give it g_autofree, to avoid the manual
g_free().
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240122221529.86562-7-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Put 'name' declaration inside the loop, with g_autofree, to avoid
manually doing g_free() in each iteration.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240122221529.86562-6-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Move 'clust_name' inside the loop, and g_autofree, to avoid having to
g_free() manually in each loop iteration.
'intc_phandles' is also g_autofreed to avoid another manual g_free().
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240122221529.86562-5-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Move all char pointers to the loop. Use g_autofree in all of them to
avoid the g_free() calls.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240122221529.86562-4-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Use g_autofree in 'dist_matrix' to avoid the manual g_free().
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240122221529.86562-3-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The 'isa' char pointer isn't being freed after use.
Issue detected by Valgrind:
==38752== 128 bytes in 1 blocks are definitely lost in loss record 3,190 of 3,884
==38752== at 0x484280F: malloc (vg_replace_malloc.c:442)
==38752== by 0x5189619: g_malloc (gmem.c:130)
==38752== by 0x51A5BF2: g_strconcat (gstrfuncs.c:628)
==38752== by 0x6C1E3E: riscv_isa_string_ext (cpu.c:2321)
==38752== by 0x6C1E3E: riscv_isa_string (cpu.c:2343)
==38752== by 0x6BD2EA: build_rhct (virt-acpi-build.c:232)
==38752== by 0x6BD2EA: virt_acpi_build (virt-acpi-build.c:556)
==38752== by 0x6BDC86: virt_acpi_setup (virt-acpi-build.c:662)
==38752== by 0x9C8DC6: notifier_list_notify (notify.c:39)
==38752== by 0x4A595A: qdev_machine_creation_done (machine.c:1589)
==38752== by 0x61E052: qemu_machine_creation_done (vl.c:2680)
==38752== by 0x61E052: qmp_x_exit_preconfig.part.0 (vl.c:2709)
==38752== by 0x6220C6: qmp_x_exit_preconfig (vl.c:2702)
==38752== by 0x6220C6: qemu_init (vl.c:3758)
==38752== by 0x425858: main (main.c:47)
Fixes: ebfd392893 ("hw/riscv/virt: virt-acpi-build.c: Add RHCT Table")
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240122221529.86562-2-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
misa_mxl_max is common for all instances of a RISC-V CPU class so they
are better put into class.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240203-riscv-v11-2-a23f4848a628@daynix.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Requests that complete in an IOThread use irqfd to notify the guest
while requests that complete in the main loop thread use the traditional
qdev irq code path. The reason for this conditional is that the irq code
path requires the BQL:
if (s->ioeventfd_started && !s->ioeventfd_disabled) {
virtio_notify_irqfd(vdev, req->vq);
} else {
virtio_notify(vdev, req->vq);
}
There is a corner case where the conditional invokes the irq code path
instead of the irqfd code path:
static void virtio_blk_stop_ioeventfd(VirtIODevice *vdev)
{
...
/*
* Set ->ioeventfd_started to false before draining so that host notifiers
* are not detached/attached anymore.
*/
s->ioeventfd_started = false;
/* Wait for virtio_blk_dma_restart_bh() and in flight I/O to complete */
blk_drain(s->conf.conf.blk);
During blk_drain() the conditional produces the wrong result because
ioeventfd_started is false.
Use qemu_in_iothread() instead of checking the ioeventfd state.
Cc: qemu-stable@nongnu.org
Buglink: https://issues.redhat.com/browse/RHEL-15394
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240122172625.415386-1-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit d3f6f294ae ("virtio-blk: always set
ioeventfd during startup") has made virtio_blk_start_ioeventfd() always
kick the virtqueue (set the ioeventfd), regardless of whether the BB is
drained. That is no longer necessary, because attaching the host
notifier will now set the ioeventfd, too; this happens either
immediately right here in virtio_blk_start_ioeventfd(), or later when
the drain ends, in virtio_blk_ioeventfd_attach().
With event_notifier_set() removed, the code becomes the same as the one
in virtio_blk_ioeventfd_attach(), so we can reuse that function.
Signed-off-by: Hanna Czenczek <hreitz@redhat.com>
Message-ID: <20240202153158.788922-4-hreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
During drain, we do not care about virtqueue notifications, which is why
we remove the handlers on it. When removing those handlers, whether vq
notifications are enabled or not depends on whether we were in polling
mode or not; if not, they are enabled (by default); if so, they have
been disabled by the io_poll_start callback.
Because we do not care about those notifications after removing the
handlers, this is fine. However, we have to explicitly ensure they are
enabled when re-attaching the handlers, so we will resume receiving
notifications. We do this in virtio_queue_aio_attach_host_notifier*().
If such a function is called while we are in a polling section,
attaching the notifiers will then invoke the io_poll_start callback,
re-disabling notifications.
Because we will always miss virtqueue updates in the drained section, we
also need to poll the virtqueue once after attaching the notifiers.
Buglink: https://issues.redhat.com/browse/RHEL-3934
Signed-off-by: Hanna Czenczek <hreitz@redhat.com>
Message-ID: <20240202153158.788922-3-hreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
As of commit 38738f7dbb ("virtio-scsi:
don't waste CPU polling the event virtqueue"), we only attach an io_read
notifier for the virtio-scsi event virtqueue instead, and no polling
notifiers. During operation, the event virtqueue is typically
non-empty, but none of the buffers are intended to be used immediately.
Instead, they only get used when certain events occur. Therefore, it
makes no sense to continuously poll it when non-empty, because it is
supposed to be and stay non-empty.
We do this by using virtio_queue_aio_attach_host_notifier_no_poll()
instead of virtio_queue_aio_attach_host_notifier() for the event
virtqueue.
Commit 766aa2de0f ("virtio-scsi: implement
BlockDevOps->drained_begin()") however has virtio_scsi_drained_end() use
virtio_queue_aio_attach_host_notifier() for all virtqueues, including
the event virtqueue. This can lead to it being polled again, undoing
the benefit of commit 38738f7dbb.
Fix it by using virtio_queue_aio_attach_host_notifier_no_poll() for the
event virtqueue.
Reported-by: Fiona Ebner <f.ebner@proxmox.com>
Fixes: 766aa2de0f
("virtio-scsi: implement BlockDevOps->drained_begin()")
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Reviewed-by: Fiona Ebner <f.ebner@proxmox.com>
Signed-off-by: Hanna Czenczek <hreitz@redhat.com>
Message-ID: <20240202153158.788922-2-hreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
usb-storage is for the most part just a wrapper around an internally
created scsi-disk device. It uses DEFINE_BLOCK_PROPERTIES() to offer all
of the usual block device properties to the user, but then only forwards
a few select properties to the internal device while the rest is
silently ignored.
This changes scsi_bus_legacy_add_drive() to accept a whole BlockConf
instead of some individual values inside of it so that usb-storage can
now pass the whole configuration to the internal scsi-disk. This enables
the remaining block device properties, e.g. logical/physical_block_size
or discard_granularity.
Buglink: https://issues.redhat.com/browse/RHEL-22375
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20240131130607.24117-1-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
QEMU's coding style generally forbids C99 mixed declarations.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240206140410.65650-1-stefanha@redhat.com>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
scsi_device_for_each_req_async() currently does not provide any way to
be awaited. One of its callers is scsi_device_purge_requests(), which
therefore currently does not guarantee that all requests are fully
settled when it returns.
We want all requests to be settled, because scsi_device_purge_requests()
is called through the unrealize path, including the one invoked by
virtio_scsi_hotunplug() through qdev_simple_device_unplug_cb(), which
most likely assumes that all SCSI requests are done then.
In fact, scsi_device_purge_requests() already contains a blk_drain(),
but this will not fully await scsi_device_for_each_req_async(), only the
I/O requests it potentially cancels (not the non-I/O requests).
However, we can have scsi_device_for_each_req_async() increment the BB
in-flight counter, and have scsi_device_for_each_req_async_bh()
decrement it when it is done. This way, the blk_drain() will fully
await all SCSI requests to be purged.
This also removes the need for scsi_device_for_each_req_async_bh() to
double-check the current context and potentially re-schedule itself,
should it now differ from the BB's context: Changing a BB's AioContext
with a root node is done through bdrv_try_change_aio_context(), which
creates a drained section. With this patch, we keep the BB in-flight
counter elevated throughout, so we know the BB's context cannot change.
Signed-off-by: Hanna Czenczek <hreitz@redhat.com>
Message-ID: <20240202144755.671354-3-hreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Hanna Czenczek <hreitz@redhat.com> noted that the array index in
virtio_blk_dma_restart_cb() is not bounds-checked:
g_autofree VirtIOBlockReq **vq_rq = g_new0(VirtIOBlockReq *, num_queues);
...
while (rq) {
VirtIOBlockReq *next = rq->next;
uint16_t idx = virtio_get_queue_index(rq->vq);
rq->next = vq_rq[idx];
^^^^^^^^^^
The code is correct because both rq->vq and vq_rq[] depend on
num_queues, but this is indirect and not 100% obvious. Add an assertion.
Suggested-by: Hanna Czenczek <hreitz@redhat.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240206190610.107963-4-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It is not possible to instantiate a virtio-blk device with 0 virtqueues.
The following check is located in ->realize():
if (!conf->num_queues) {
error_setg(errp, "num-queues property must be larger than 0");
return;
}
Later on we access s->vq_aio_context[0] under the assumption that there
is as least one virtqueue. Hanna Czenczek <hreitz@redhat.com> noted that
it would help to show that the array index is already valid.
Add an assertion to document that s->vq_aio_context[0] is always
safe...and catch future code changes that break this assumption.
Suggested-by: Hanna Czenczek <hreitz@redhat.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240206190610.107963-3-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Hanna Czenczek <hreitz@redhat.com> noticed that the safety of
`vq_aio_context[vq->value] = ctx;` with user-defined vq->value inputs is
not obvious.
The code is structured in validate() + apply() steps so input validation
is there, but it happens way earlier and there is nothing that
guarantees apply() can only be called with validated inputs.
This patch moves the validate() call inside the apply() function so
validation is guaranteed. I also added the bounds checking assertion
that Hanna suggested.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Message-ID: <20240206190610.107963-2-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
QEMU initializes preallocated backend memory as the objects are parsed from
the command line. This is not optimal in some cases (e.g. memory spanning
multiple NUMA nodes) because the memory objects are initialized in series.
Allow the initialization to occur in parallel (asynchronously). In order to
ensure optimal thread placement, asynchronous initialization requires prealloc
context threads to be in use.
Signed-off-by: Mark Kanda <mark.kanda@oracle.com>
Message-ID: <20240131165327.3154970-2-mark.kanda@oracle.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
We used to check that the memory region size is multiples of the overall
requested address alignment for the device memory address.
We removed that check, because there are cases (i.e., hv-balloon) where
devices unconditionally request an address alignment that has a very large
alignment (i.e., 32 GiB), but the actual memory device size might not be
multiples of that alignment.
However, this change:
(a) allows for some practically impossible DIMM sizes, like "1GB+1 byte".
(b) allows for DIMMs that partially cover hugetlb pages, previously
reported in [1].
Both scenarios don't make any sense: we might even waste memory.
So let's reintroduce that check, but only check that the
memory region size is multiples of the memory region alignment (i.e.,
page size, huge page size), but not any additional memory device
requirements communicated using md->get_min_alignment().
The following examples now fail again as expected:
(a) 1M with 2M THP
qemu-system-x86_64 -m 4g,maxmem=16g,slots=1 -S -nodefaults -nographic \
-object memory-backend-ram,id=mem1,size=1M \
-device pc-dimm,id=dimm1,memdev=mem1
-> backend memory size must be multiple of 0x200000
(b) 1G+1byte
qemu-system-x86_64 -m 4g,maxmem=16g,slots=1 -S -nodefaults -nographic \
-object memory-backend-ram,id=mem1,size=1073741825B \
-device pc-dimm,id=dimm1,memdev=mem1
-> backend memory size must be multiple of 0x200000
(c) Unliagned hugetlb size (2M)
qemu-system-x86_64 -m 4g,maxmem=16g,slots=1 -S -nodefaults -nographic \
-object memory-backend-file,id=mem1,mem-path=/dev/hugepages/tmp,size=511M \
-device pc-dimm,id=dimm1,memdev=mem1
backend memory size must be multiple of 0x200000
(d) Unliagned hugetlb size (1G)
qemu-system-x86_64 -m 4g,maxmem=16g,slots=1 -S -nodefaults -nographic \
-object memory-backend-file,id=mem1,mem-path=/dev/hugepages1G/tmp,size=2047M \
-device pc-dimm,id=dimm1,memdev=mem1
-> backend memory size must be multiple of 0x40000000
Note that this fix depends on a hv-balloon change to communicate its
additional alignment requirements using get_min_alignment() instead of
through the memory region.
[1] https://lkml.kernel.org/r/f77d641d500324525ac036fe1827b3070de75fc1.1701088320.git.mprivozn@redhat.com
Message-ID: <20240117135554.787344-3-david@redhat.com>
Reported-by: Zhenyu Zhang <zhenyzha@redhat.com>
Reported-by: Michal Privoznik <mprivozn@redhat.com>
Fixes: eb1b7c4bd4 ("memory-device: Drop size alignment check")
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
The character "+" is now forbidden in QOM device names (see commit
b447378e12 - "Limit type names to alphanumerical and some few special
characters"). For the "power5+" and "power7+" CPU names, there is
currently a hack in type_name_is_valid() to still allow them for
compatibility reasons. However, there is a much nicer solution for this:
Simply use aliases! This way we can still support the old names without
the need for the ugly hack in type_name_is_valid().
Message-ID: <20240117141054.73841-2-thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
When the maximum count of SCRIPTS instructions is reached, the code
stops execution and returns, but fails to decrement the reentrancy
counter. This effectively renders the SCSI controller unusable
because on next entry the reentrancy counter is still above the limit.
This bug was seen on HP-UX 10.20 which seems to trigger SCRIPTS
loops.
Fixes: b987718bbb ("hw/scsi/lsi53c895a: Fix reentrancy issues in the LSI controller (CVE-2023-0330)")
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-ID: <20240128202214.2644768-1-svens@stackframe.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Let's implement the get_min_alignment() callback for memory devices, and
copy for the device memory region the alignment of the host memory
region. This mimics what virtio-mem does, and allows for re-introducing
proper alignment checks for the memory region size (where we don't care
about additional device requirements) in memory device core.
Message-ID: <20240117135554.787344-2-david@redhat.com>
Reviewed-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
This function is no longer used, as all its callers have been converted
to use pci_init_nic_devices() instead.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Obtain the MAC address from the NIC configuration if there is one, or
generate one explicitly so that it can be placed in the PROM.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Create the device only if there is a corresponding NIC config for it.
Remove the explicit check on nd_table[0].used from hw/hppa/machine.c
which (since commit d8a3220005) tries to do the same thing.
The lasi_82596 support has been disabled since it was first introduced,
since enable_lasi_lan() has always been zero. This allows the user to
enable it by explicitly requesting a NIC model 'lasi_82596' or just
using the alias 'lasi'. Otherwise, it defaults to a PCI NIC as before.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
When converting to the shiny build-system-du-jour, a typo prevented the
last_i82596 driver from being built. Correct the config option name to
re-enable the build. And include "sysemu/sysemu.h" so it actually builds.
Fixes: b1419fa665 ("meson: convert hw/net")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2144
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
The MIPS SIM platform instantiates its NIC only if a corresponding
configuration exists for it. Use qemu_create_nic_device() function for
that.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
If a corresponding NIC configuration was found, it will have a MAC address
already assigned, so use that. Else, generate and assign a default one.
Using qemu_find_nic_info() is simpler than the alternative of using
qemu_configure_nic_device() and then having to fetch the "mac" property
as a string and convert it.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Rather than just using qemu_configure_nic_device(), populate the MAC
address in the system-registers device by peeking at the NICInfo before
it's assigned to the device.
Generate the MAC address early, if there is no matching -nic option.
Otherwise the MAC address wouldn't be generated until net_client_init1()
runs.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Also update the test to specify which device to attach the test socket
to, and remove the comment lamenting the fact that we can't do so.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Some callers instantiate the device unconditionally, others will do so only
if there is a NICInfo to go with it. This appears to be fairly random, but
preseve the existing behaviour for now.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Some callers instantiate the device unconditionally, others will do so only
if there is a NICInfo to go with it. This appears to be fairly random, but
preserve the existing behaviour of each caller for now.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
The first sunhme NIC gets placed a function 1 on slot 1 of PCI bus A,
and the rest are dynamically assigned on PCI bus B.
Previously, any PCI NIC would get the special treatment purely by
virtue of being first in the list.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Previously, the first PCI NIC would be assigned to slot 2 even if the
user override the model and made it something other than an rtl8139
which is the default. Everything else would be dynamically assigned.
Now, the first rtl8139 gets slot 2 and everything else is dynamic.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Avoid directly referencing nd_table[] by first instantiating any
spapr-vlan devices using a qemu_get_nic_info() loop, then calling
pci_init_nic_devices() to do the rest.
No functional change intended.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Previously, the first PCI NIC would be placed in PCI slot 3 and the rest
would be dynamically assigned. Even if the user overrode the default NIC
type and made it something other than PCNet.
Now, the first PCNet NIC (that is, anything not explicitly specified
to be anything different) will go to slot 3 even if it isn't the first
NIC specified on the command line. And anything else will be dynamically
assigned.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
The Malta board setup code would previously place the first NIC into PCI
slot 11 if was a PCNet card, and the rest (including the first if it was
anything other than a PCNet card) would be dynamically assigned.
Now it will place any PCNet NIC into slot 11, and then anything else will
be dynamically assigned.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
The previous behaviour was: *if* the first NIC specified on the command
line was an RTL8139 (or unspecified model) then it gets assigned to PCI
slot 7, which is where the Fuloong board had an RTL8139. All other
devices (including the first, if it was specified as anything other than
an rtl8319) get dynamically assigned on the bus.
The new behaviour is subtly different: If the first NIC was given a
specific model *other* than rtl8139, and a subsequent NIC was not,
then the rtl8139 (or unspecified) NIC will go to slot 7 and the rest
will be dynamically assigned.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
When instantiating XenBus itself, for each NIC which is configured with
either the model unspecified, or set to to "xen" or "xen-net-device",
create a corresponding xen-net-device for it.
Now we can revert the previous more hackish version which relied on the
platform code explicitly registering the NICs on its own XenBus, having
returned the BusState* from xen_bus_init() itself.
This also fixes the setup for Xen PV guests, which was previously broken
in various ways and never actually managed to peer with the netdev.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Eliminate direct access to nd_table[] and nb_nics by processing the the
Xen and ISA NICs first and then calling pci_init_nic_devices() for the
rest.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
The loop over nd_table[] to add PCI NICs is repeated in quite a few
places. Add a helper function to do it.
Some platforms also try to instantiate a specific model in a specific
slot, to match the real hardware. Add pci_init_nic_in_slot() for that
purpose.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
This patch will allow the SPI controller to be accessible from BCM2835 based
boards as SPI0. SPI driver is usually disabled by default and config.txt does
not work.
Instead, dtmerge can be used to apply spi=on on a bcm2835 dtb file.
Signed-off-by: Rayhan Faizel <rayhan.faizel@gmail.com>
Message-id: 20240129221807.2983148-3-rayhan.faizel@gmail.com
[PMM: indent tweak]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds the SPI controller for the BCM2835. Polling and interrupt modes
of transfer are supported. DMA and LoSSI modes are currently unimplemented.
Signed-off-by: Rayhan Faizel <rayhan.faizel@gmail.com>
Message-id: 20240129221807.2983148-2-rayhan.faizel@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- Implementation of Transmit function for packets
- Implementation for reading and writing from and to descriptors in
memory for Tx
Added relevant trace-events
NOTE: This function implements the steps detailed in the datasheet for
transmitting messages from the GMAC.
Change-Id: Icf14f9fcc6cc7808a41acd872bca67c9832087e6
Signed-off-by: Nabih Estefan <nabihestefan@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Message-id: 20240131002800.989285-6-nabihestefan@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- Implementation of Receive function for packets
- Implementation for reading and writing from and to descriptors in
memory for Rx
When RX starts, we need to flush the queued packets so that they
can be received by the GMAC device. Without this it won't work
with TAP NIC device.
When RX descriptor list is full, it returns a DMA_STATUS for
software to handle it. But there's no way to indicate the software has
handled all RX descriptors and the whole pipeline stalls.
We do something similar to NPCM7XX EMC to handle this case.
1. Return packet size when RX descriptor is full, effectively dropping
these packets in such a case.
2. When software clears RX descriptor full bit, continue receiving
further packets by flushing QEMU packet queue.
Added relevant trace-events
Change-Id: I132aa254a94cda1a586aba2ea33bbfc74ecdb831
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Nabih Estefan <nabihestefan@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Message-id: 20240131002800.989285-5-nabihestefan@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements the basic registers of GMAC device and sets
registers for networking functionalities.
Squashed IRQ Implementation patch into this one for compliation.
Tested:
The following message shows up with the change:
Broadcom BCM54612E stmmac-0:00: attached PHY driver [Broadcom BCM54612E] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
stmmaceth f0802000.eth eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Change-Id: If71c6d486b95edcccba109ba454870714d7e0940
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Nabih Estefan Diaz <nabihestefan@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Message-id: 20240131002800.989285-2-nabihestefan@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
According to the QEMU Coding Style document:
> Do not use printf(), fprintf() or monitor_printf(). Instead, use
> error_report() or error_vreport() from error-report.h. This ensures the
> error is reported in the right place (current monitor or stderr), and in
> a uniform format.
> Use error_printf() & friends to print additional information.
This commit changes fprintfs that report warnings and errors to the
appropriate report functions.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 42a8953553cf68e8bacada966f93af4fbce45919.1706544115.git.manos.pitsidianakis@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tracing DPRINTFs to stderr might not be desired. A developer that relies
on tracepoints should be able to opt-in to each tracepoint and rely on
QEMU's log redirection, instead of stderr by default.
This commit converts DPRINTFs in this file that are used for tracing
into tracepoints.
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: b000ab73022dfeb7a7ab0ee8fd0f41fb208adaf0.1706544115.git.manos.pitsidianakis@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tracing DPRINTFs to stderr might not be desired. A developer that relies
on tracepoints should be able to opt-in to each tracepoint and rely on
QEMU's log redirection, instead of stderr by default.
This commit converts DPRINTFs in this file that are used for tracing
into tracepoints.
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 2fbe1fbc59078e384761c932e97cfa4276a53d75.1706544115.git.manos.pitsidianakis@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tracing DPRINTFs to stderr might not be desired. A developer that relies
on trace events should be able to opt-in to each trace event and rely on
QEMU's log redirection, instead of stderr by default.
This commit converts DPRINTFs in this file that are used for tracing
into trace events. Errors or warnings are converted to error_report and
warn_report calls.
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: fe5e3bd54231abe933f95a24e0e88208cd8cfd8f.1706544115.git.manos.pitsidianakis@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tracing DPRINTFs to stderr might not be desired. A developer that relies
on trace events should be able to opt-in to each trace event and rely on
QEMU's log redirection, instead of stderr by default.
This commit converts DPRINTFs in this file that are used for tracing
into trace events. DPRINTFs that report guest errors are logged with
LOG_GUEST_ERROR.
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 799c5141c5751cf2341e1d095349612e046424a8.1706544115.git.manos.pitsidianakis@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tracing DPRINTFs to stderr might not be desired. A developer that relies
on trace events should be able to opt-in to each trace event and rely on
QEMU's log redirection, instead of stderr by default.
This commit converts DPRINTFs in this file that are used for tracing
into trace events. DPRINTFs that report guest errors are logged with
LOG_GUEST_ERROR.#
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 39db71dd87bf2007cf7812f3d91dde53887f1f2f.1706544115.git.manos.pitsidianakis@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The latest version of qemu (v8.2.0-869-g7a1dc45af5) crashes when booting
the mcimx7d-sabre emulation with Linux v5.11 and later.
qemu-system-arm: ../system/memory.c:2750: memory_region_set_alias_offset: Assertion `mr->alias' failed.
Problem is that the Designware PCIe emulation accepts the full value range
for the iATU Viewport Register. However, both hardware and emulation only
support four inbound and four outbound viewports.
The Linux kernel determines the number of supported viewports by writing
0xff into the viewport register and reading the value back. The expected
value when reading the register is the highest supported viewport index.
Match that code by masking the supported viewport value range when the
register is written. With this change, the Linux kernel reports
imx6q-pcie 33800000.pcie: iATU: unroll F, 4 ob, 4 ib, align 0K, limit 4G
as expected and supported.
Fixes: d64e5eabc4 ("pci: Add support for Designware IP block")
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Nikita Ostrenkov <n.ostrenkov@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20240129060055.2616989-1-linux@roeck-us.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Leverage the common code introduced in commit c9cf636d48 ("machine:
Add a valid_cpu_types property") to check for the single valid CPU
type. Remove the now unused MachineClass::default_cpu_type field.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240129151828.59544-10-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Leverage the common code introduced in commit c9cf636d48 ("machine:
Add a valid_cpu_types property") to check for the single valid CPU
type. Remove the now unused MachineClass::default_cpu_type field.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240129151828.59544-9-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The npcm7xx Soc is created with a Cortex-A9 core, see in
hw/arm/npcm7xx.c:
static void npcm7xx_init(Object *obj)
{
NPCM7xxState *s = NPCM7XX(obj);
for (int i = 0; i < NPCM7XX_MAX_NUM_CPUS; i++) {
object_initialize_child(obj, "cpu[*]", &s->cpu[i],
ARM_CPU_TYPE_NAME("cortex-a9"));
}
The MachineClass::default_cpu_type field is ignored: delete it.
Use the common code introduced in commit c9cf636d48 ("machine: Add
a valid_cpu_types property") to check for valid CPU type at the
board level.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240129151828.59544-8-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Musca boards use the embedded subsystems (SSE) tied to a specific
Cortex core. Our models only use the Cortex-M33.
Use the common code introduced in commit c9cf636d48 ("machine: Add
a valid_cpu_types property") to check for valid CPU type at the
board level.
Remove the now unused MachineClass::default_cpu_type field.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240129151828.59544-7-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The M2Sxxx SoC family can only be used with Cortex-M3.
Propagating the CPU type from the board level is pointless.
Hard-code the CPU type at the SoC level.
Remove the now ignored MachineClass::default_cpu_type field.
Use the common code introduced in commit c9cf636d48 ("machine: Add
a valid_cpu_types property") to check for valid CPU type at the
board level.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240129151828.59544-6-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Restrict MachineClass::valid_cpu_types[] to the single
valid CPU types.
Instead of ignoring invalid CPU type requested by the user:
$ qemu-system-arm -M midway -cpu cortex-a7 -S -monitor stdio
QEMU 8.2.50 monitor - type 'help' for more information
(qemu) info qom-tree
/machine (midway-machine)
/cpu[0] (cortex-a15-arm-cpu)
...
we now display an error:
$ qemu-system-arm -M midway -cpu cortex-a7
qemu-system-arm: Invalid CPU model: cortex-a7
The only valid type is: cortex-a15
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20240129151828.59544-5-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QDev objects created with qdev_new() need to manually add
their parent relationship with object_property_add_child().
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20240129151828.59544-4-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Restrict MachineClass::valid_cpu_types[] to the single
valid CPU type.
Instead of ignoring invalid CPU type requested by the user:
$ qemu-system-arm -M nuri -cpu cortex-a7 -S -monitor stdio
QEMU 8.2.50 monitor - type 'help' for more information
(qemu) info qom-tree
/machine (nuri-machine)
/soc (exynos4210)
/cpu[0] (cortex-a9-arm-cpu)
...
We now display an error:
$ qemu-system-arm -M nuri -cpu cortex-a7
qemu-system-arm: Invalid CPU model: cortex-a7
The only valid type is: cortex-a9
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20240129151828.59544-3-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QDev objects created with qdev_new() need to manually add
their parent relationship with object_property_add_child().
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20240129151828.59544-2-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
BusClass currently has transitional infrastructure to support
subclasses which implement the legacy BusClass::reset method rather
than the Resettable interface. We have now removed all the users of
BusClass::reset in the tree, so we can remove the transitional
infrastructure.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cédric Le Goater <clg@redhat.com>
Acked-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Tested-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-id: 20240119163512.3810301-6-peter.maydell@linaro.org
Switch the s390x virtual-css bus from using BusClass::reset to the
Resettable interface.
This has no behavioural change, because the BusClass code to support
subclasses that use the legacy BusClass::reset will call that method
in the hold phase of 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cédric Le Goater <clg@redhat.com>
Acked-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Tested-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-id: 20240119163512.3810301-5-peter.maydell@linaro.org
Switch the ADB bus from using BusClass::reset to the Resettable
interface.
This has no behavioural change, because the BusClass code to support
subclasses that use the legacy BusClass::reset will call that method
in the hold phase of 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cédric Le Goater <clg@redhat.com>
Acked-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Tested-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-id: 20240119163512.3810301-4-peter.maydell@linaro.org
Switch vmbus from using BusClass::reset to the Resettable interface.
This has no behavioural change, because the BusClass code to support
subclasses that use the legacy BusClass::reset will call that method
in the hold phase of 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cédric Le Goater <clg@redhat.com>
Acked-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Tested-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-id: 20240119163512.3810301-3-peter.maydell@linaro.org
Switch the PCI bus from using BusClass::reset to the Resettable
interface.
This has no behavioural change, because the BusClass code to support
subclasses that use the legacy BusClass::reset will call that method
in the hold phase of 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-id: 20240119163512.3810301-2-peter.maydell@linaro.org
* Update of buildroot images to 2023.11 (6.6.3 kernel)
* Check of the valid CPU type supported by aspeed machines
* Simplified models for the IBM's FSI bus and the Aspeed
controller bridge
-----BEGIN PGP SIGNATURE-----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=0C5S
-----END PGP SIGNATURE-----
Merge tag 'pull-aspeed-20240201' of https://github.com/legoater/qemu into staging
aspeed queue:
* Update of buildroot images to 2023.11 (6.6.3 kernel)
* Check of the valid CPU type supported by aspeed machines
* Simplified models for the IBM's FSI bus and the Aspeed
controller bridge
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmW7Sa8ACgkQUaNDx8/7
# 7KG7mw/8DbMJY6aqgq5YANszzem1ktJphPCNxq081cbczCOUpCNX4aL+0/ANvxxD
# lbJQB+SZeIRmuFbxYPhq68rtzB4vG7tsQpns4H33EPKT4vuzF70lq4fgptMiun3q
# 1ZJ2LF3jonvQWdhbC17wzAQz0FFb4F7XOxz++UL4okPsgzsYItnd+TWs8q7+erRb
# 84UwN+eBTBAl/FiNk679/tBTqAfCVGgQ7dzotr4f3tg5POvrGOrlEjAn0O+dGGDj
# wgILmpEBsTsilRB1tz8Kw0j/v/VkHz1DJu45lRAV9CIrN22iKcjMilNGgNDT8kcI
# yAlxAw3iN+hVFqDov8wFPjDYd/Qw2oRAPy2Kd14hW9xL8zBOTms1JK5L0PS2+Feo
# ZjMJ2cOJq3t4Wt1ZXRhgHfF4ANwP0OZ/y9bHCy3CkBljEeiTQbikHP9gVV4qHXZH
# 4Q0HnDZQwAgobw3CmZ8jVx1dQueqy3ycuvkhCyv3S0l/tdbtXDtr5pNNu3dAP/PJ
# 3nifLdRImhDvxxO9GKaCdUVLzELzMJl0GrgAsVJPKVnKHA4IiVKmB+XcW9IUbfy/
# 3zA2wHJLrEF+MF6MsuNcEYCCqUvyNLm7rUrXk1wNLXpCJ35bbW5IYy7Ty/8E2GHb
# D5Cv/EPNhMBiNA4+HqQlMOTC13Ozv2qwCuWYCh2Ik8mnzaEiyTo=
# =0C5S
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 01 Feb 2024 07:35:11 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-aspeed-20240201' of https://github.com/legoater/qemu:
hw/fsi: Update MAINTAINER list
hw/fsi: Added FSI documentation
hw/fsi: Added qtest
hw/arm: Hook up FSI module in AST2600
hw/fsi: Aspeed APB2OPB & On-chip peripheral bus
hw/fsi: Introduce IBM's FSI master
hw/fsi: Introduce IBM's cfam
hw/fsi: Introduce IBM's fsi-slave model
hw/fsi: Introduce IBM's FSI Bus
hw/fsi: Introduce IBM's scratchpad device
hw/fsi: Introduce IBM's Local bus
hw/arm/aspeed: Check for CPU types in machine_run_board_init()
hw/arm/aspeed: Introduce aspeed_soc_cpu_type() helper
hw/arm/aspeed: Init CPU defaults in a common helper
hw/arm/aspeed: Set default CPU count using aspeed_soc_num_cpus()
hw/arm/aspeed: Remove dead code
tests/avocado/machine_aspeed.py: Update buildroot images to 2023.11
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patchset introduces IBM's Flexible Service Interface(FSI).
Time for some fun with inter-processor buses. FSI allows a service
processor access to the internal buses of a host POWER processor to
perform configuration or debugging.
FSI has long existed in POWER processes and so comes with some baggage,
including how it has been integrated into the ASPEED SoC.
Working backwards from the POWER processor, the fundamental pieces of
interest for the implementation are:
1. The Common FRU Access Macro (CFAM), an address space containing
various "engines" that drive accesses on buses internal and external
to the POWER chip. Examples include the SBEFIFO and I2C masters. The
engines hang off of an internal Local Bus (LBUS) which is described
by the CFAM configuration block.
2. The FSI slave: The slave is the terminal point of the FSI bus for
FSI symbols addressed to it. Slaves can be cascaded off of one
another. The slave's configuration registers appear in address space
of the CFAM to which it is attached.
3. The FSI master: A controller in the platform service processor (e.g.
BMC) driving CFAM engine accesses into the POWER chip. At the
hardware level FSI is a bit-based protocol supporting synchronous and
DMA-driven accesses of engines in a CFAM.
4. The On-Chip Peripheral Bus (OPB): A low-speed bus typically found in
POWER processors. This now makes an appearance in the ASPEED SoC due
to tight integration of the FSI master IP with the OPB, mainly the
existence of an MMIO-mapping of the CFAM address straight onto a
sub-region of the OPB address space.
5. An APB-to-OPB bridge enabling access to the OPB from the ARM core in
the AST2600. Hardware limitations prevent the OPB from being directly
mapped into APB, so all accesses are indirect through the bridge.
The implementation appears as following in the qemu device tree:
(qemu) info qtree
bus: main-system-bus
type System
...
dev: aspeed.apb2opb, id ""
gpio-out "sysbus-irq" 1
mmio 000000001e79b000/0000000000001000
bus: opb.1
type opb
dev: fsi.master, id ""
bus: fsi.bus.1
type fsi.bus
dev: cfam.config, id ""
dev: cfam, id ""
bus: fsi.lbus.1
type lbus
dev: scratchpad, id ""
address = 0 (0x0)
bus: opb.0
type opb
dev: fsi.master, id ""
bus: fsi.bus.0
type fsi.bus
dev: cfam.config, id ""
dev: cfam, id ""
bus: fsi.lbus.0
type lbus
dev: scratchpad, id ""
address = 0 (0x0)
The LBUS is modelled to maintain the qdev bus hierarchy and to take
advantage of the object model to automatically generate the CFAM
configuration block. The configuration block presents engines in the
order they are attached to the CFAM's LBUS. Engine implementations
should subclass the LBusDevice and set the 'config' member of
LBusDeviceClass to match the engine's type.
CFAM designs offer a lot of flexibility, for instance it is possible for
a CFAM to be simultaneously driven from multiple FSI links. The modeling
is not so complete; it's assumed that each CFAM is attached to a single
FSI slave (as a consequence the CFAM subclasses the FSI slave).
As for FSI, its symbols and wire-protocol are not modelled at all. This
is not necessary to get FSI off the ground thanks to the mapping of the
CFAM address space onto the OPB address space - the models follow this
directly and map the CFAM memory region into the OPB's memory region.
Future work includes supporting more advanced accesses that drive the
FSI master directly rather than indirectly via the CFAM mapping, which
will require implementing the FSI state machine and methods for each of
the FSI symbols on the slave. Further down the track we can also look at
supporting the bitbanged SoftFSI drivers in Linux by extending the FSI
slave model to resolve sequences of GPIO IRQs into FSI symbols, and
calling the associated symbol method on the slave to map the access onto
the CFAM.
Testing:
Tested by reading cfam config address 0 on rainier machine type.
root@p10bmc:~# pdbg -a getcfam 0x0
p0: 0x0 = 0xc0022d15
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
An APB-to-OPB bridge enabling access to the OPB from the ARM core in
the AST2600. Hardware limitations prevent the OPB from being directly
mapped into APB, so all accesses are indirect through the bridge.
The On-Chip Peripheral Bus (OPB): A low-speed bus typically found in
POWER processors. This now makes an appearance in the ASPEED SoC due
to tight integration of the FSI master IP with the OPB, mainly the
existence of an MMIO-mapping of the CFAM address straight onto a
sub-region of the OPB address space.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - moved FSIMasterState under AspeedAPB2OPBState
- modified fsi_opb_fsi_master_address() and
fsi_opb_opb2fsi_address()
- instroduced fsi_aspeed_apb2opb_init()
- reworked fsi_aspeed_apb2opb_realize()
- removed FSIMasterState object and fsi_opb_realize()
- simplified OPBus
- introduced fsi_aspeed_apb2opb_rw to fix endianness issue ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
This commit models the FSI master. CFAM is hanging out of FSI master which is a bus controller.
The FSI master: A controller in the platform service processor (e.g.
BMC) driving CFAM engine accesses into the POWER chip. At the
hardware level FSI is a bit-based protocol supporting synchronous and
DMA-driven accesses of engines in a CFAM.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - move FSICFAMState object under FSIMasterState
- introduced fsi_master_init()
- reworked fsi_master_realize()
- dropped FSIBus definition ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
The Common FRU Access Macro (CFAM), an address space containing
various "engines" that drive accesses on busses internal and external
to the POWER chip. Examples include the SBEFIFO and I2C masters. The
engines hang off of an internal Local Bus (LBUS) which is described
by the CFAM configuration block.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - moved object FSIScratchPad under FSICFAMState
- moved FSIScratchPad code under cfam.c
- introduced fsi_cfam_instance_init()
- reworked fsi_cfam_realize() ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
The FSI slave: The slave is the terminal point of the FSI bus for
FSI symbols addressed to it. Slaves can be cascaded off of one
another. The slave's configuration registers appear in address space
of the CFAM to which it is attached.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where FSI bus is introduced.
The FSI bus is a simple bus where FSI master is attached.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - removed include/hw/fsi/engine-scratchpad.h and
hw/fsi/engine-scratchpad.c
- dropped FSI_SCRATCHPAD
- included FSIBus definition
- dropped hw/fsi/trace-events changes ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
The scratchpad provides a set of non-functional registers. The firmware
is free to use them, hardware does not support any special management
support. The scratchpad registers can be read or written from LBUS
slave. The scratch pad is managed under FSI CFAM state.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - moved object FSIScratchPad under FSICFAMState
- moved FSIScratchPad code under cfam.c ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
The LBUS is modelled to maintain mapped memory for the devices. The
memory is mapped after CFAM config, peek table and FSI slave registers.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - removed lbus_add_device() bc unused
- removed lbus_create_device() bc used only once
- removed "address" property
- updated meson.build to build fsi dir
- included an empty hw/fsi/trace-events ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Aspeed SoCs use a single CPU type (set as AspeedSoCClass::cpu_type).
Convert it to a NULL-terminated array (of a single non-NULL element).
Set MachineClass::valid_cpu_types[] to use the common machine code
to provide hints when the requested CPU is invalid (see commit
e702cbc19e ("machine: Improve is_cpu_type_supported()").
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
In order to alter AspeedSoCClass::cpu_type in the next
commit, introduce the aspeed_soc_cpu_type() helper to
retrieve the per-SoC CPU type from AspeedSoCClass.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Rework aspeed_soc_num_cpus() as a new init_cpus_defaults()
helper to reduce code duplication.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Since commit b7f1a0cb76 ("arm/aspeed: Compute the number
of CPUs from the SoC definition") Aspeed machines use the
aspeed_soc_num_cpus() helper to set the number of CPUs.
Use it for the ast1030-evb (commit 356b230ed1 "aspeed/soc:
Add AST1030 support") and supermicrox11-bmc (commit 40a38df55e
"hw/arm/aspeed: Add board model for Supermicro X11 BMC") machines.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Remove copy/paste typo from commit 6c323aba40 ("hw/arm/aspeed:
Adding new machine Tiogapass in QEMU").
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEe3O61ovnosKJMUsicBtPaxppPlkFAmW6NScPHG1qdEB0bHMu
bXNrLnJ1AAoJEHAbT2saaT5ZdQYH/2fhfhZotH0V2qAcMxlOoHbAE9UhZNRsSYtf
QFP0GXFYFAMm7LHkPUbvKgO7LylKWAOMn/zKZqgj1Vf1EpoKQ2FwLtR/buDz86Ec
pi2OrDPRA7Ay5c3ow3YZZkUOhQTTcR5rNjYctPtt/J4j8ol/z5vre7weJIg2bCJe
zI7vIVg7iFFzbkXY20KHngJ5nDC+aEm7WaGlxAP8kfkvy324Wy9O2k8qu2J5zbLT
HGvh3rwEDvRTYe4CaKFFHWNV0m4092HAr/dJBobugI5VZ6QQpK6Tgy8N+4ZrCHD2
SjUKeym85VTOYGuY8b18fk5MQK2SzsfBUJ4x8VGC75W4mJ8agdc=
=HImO
-----END PGP SIGNATURE-----
Merge tag 'pull-trivial-patches' of https://gitlab.com/mjt0k/qemu into staging
trivial patches for 2024-01-31
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEe3O61ovnosKJMUsicBtPaxppPlkFAmW6NScPHG1qdEB0bHMu
# bXNrLnJ1AAoJEHAbT2saaT5ZdQYH/2fhfhZotH0V2qAcMxlOoHbAE9UhZNRsSYtf
# QFP0GXFYFAMm7LHkPUbvKgO7LylKWAOMn/zKZqgj1Vf1EpoKQ2FwLtR/buDz86Ec
# pi2OrDPRA7Ay5c3ow3YZZkUOhQTTcR5rNjYctPtt/J4j8ol/z5vre7weJIg2bCJe
# zI7vIVg7iFFzbkXY20KHngJ5nDC+aEm7WaGlxAP8kfkvy324Wy9O2k8qu2J5zbLT
# HGvh3rwEDvRTYe4CaKFFHWNV0m4092HAr/dJBobugI5VZ6QQpK6Tgy8N+4ZrCHD2
# SjUKeym85VTOYGuY8b18fk5MQK2SzsfBUJ4x8VGC75W4mJ8agdc=
# =HImO
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 31 Jan 2024 11:55:19 GMT
# gpg: using RSA key 7B73BAD68BE7A2C289314B22701B4F6B1A693E59
# gpg: issuer "mjt@tls.msk.ru"
# gpg: Good signature from "Michael Tokarev <mjt@tls.msk.ru>" [full]
# gpg: aka "Michael Tokarev <mjt@corpit.ru>" [full]
# gpg: aka "Michael Tokarev <mjt@debian.org>" [full]
# Primary key fingerprint: 6EE1 95D1 886E 8FFB 810D 4324 457C E0A0 8044 65C5
# Subkey fingerprint: 7B73 BAD6 8BE7 A2C2 8931 4B22 701B 4F6B 1A69 3E59
* tag 'pull-trivial-patches' of https://gitlab.com/mjt0k/qemu: (21 commits)
hw/hyperv: Include missing headers
hw/intc/xics: Include missing 'cpu.h' header
hw/arm: Add `\n` to hint message
hw/loongarch: Add `\n` to hint message
hw/i386: Add `\n` to hint message
backends/hostmem: Fix block comments style (checkpatch.pl warnings)
misc: Clean up includes
riscv: Clean up includes
cxl: Clean up includes
include: Clean up includes
m68k: Clean up includes
acpi: Clean up includes
aspeed: Clean up includes
disas/riscv: Clean up includes
hyperv: Clean up includes
scripts/clean-includes: Update exclude list
mailmap: Fix Stefan Weil email
qemu-docs: Update options for graphical frontends
qapi/migration.json: Fix the member name for MigrationCapability
colo: examples: remove mentions of script= and (wrong) downscript=
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In cases where a device tries to read more bytes than the block device
contains, the error is vague: "device requires X bytes, block backend
provides Y bytes".
This patch changes the errors of this function to include the block
backend name, the device id and device type name where appropriate.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-id: 7260eadff22c08457740117c1bb7bd2b4353acb9.1706598705.git.manos.pitsidianakis@linaro.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add a simple method to return some kind of human readable identifier for
use in error messages.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-id: 8b566bfced98ae44be1fcc1f8e7215f0c3393aa1.1706598705.git.manos.pitsidianakis@linaro.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The following expression is incorrect because blk_pread_nonzeroes()
deals in units of bytes, not sectors:
bytes = MIN(size - offset, BDRV_REQUEST_MAX_SECTORS)
^^^^^^^
BDRV_REQUEST_MAX_BYTES is the appropriate constant.
Fixes: a4b15a8b9e ("pflash: Only read non-zero parts of backend image")
Cc: Xiang Zheng <zhengxiang9@huawei.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240130002712.257815-1-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Include missing headers in order to avoid when refactoring
unrelated headers:
hw/hyperv/hyperv.c:33:18: error: field ‘msg_page_mr’ has incomplete type
33 | MemoryRegion msg_page_mr;
| ^~~~~~~~~~~
hw/hyperv/hyperv.c: In function ‘synic_update’:
hw/hyperv/hyperv.c:64:13: error: implicit declaration of function ‘memory_region_del_subregion’ [-Werror=implicit-function-declaration]
64 | memory_region_del_subregion(get_system_memory(),
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
hw/hyperv/hyperv.c: In function ‘hyperv_hcall_signal_event’:
hw/hyperv/hyperv.c:683:17: error: implicit declaration of function ‘ldq_phys’; did you mean ‘ldub_phys’? [-Werror=implicit-function-declaration]
683 | param = ldq_phys(&address_space_memory, addr);
| ^~~~~~~~
| ldub_phys
hw/hyperv/hyperv.c:683:17: error: nested extern declaration of ‘ldq_phys’ [-Werror=nested-externs]
hw/hyperv/hyperv.c: In function ‘hyperv_hcall_retreive_dbg_data’:
hw/hyperv/hyperv.c:792:24: error: ‘TARGET_PAGE_SIZE’ undeclared (first use in this function); did you mean ‘TARGET_PAGE_BITS’?
792 | msg.u.recv.count = TARGET_PAGE_SIZE - sizeof(*debug_data_out);
| ^~~~~~~~~~~~~~~~
| TARGET_PAGE_BITS
hw/hyperv/hyperv.c: In function ‘hyperv_syndbg_send’:
hw/hyperv/hyperv.c:885:16: error: ‘HV_SYNDBG_STATUS_INVALID’ undeclared (first use in this function)
885 | return HV_SYNDBG_STATUS_INVALID;
| ^~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Include missing headers in order to avoid when refactoring
unrelated headers:
hw/intc/xics.c: In function 'icp_realize':
hw/intc/xics.c:304:5: error: unknown type name 'PowerPCCPU'
304 | PowerPCCPU *cpu;
| ^~~~~~~~~~
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This commit was created with scripts/clean-includes.
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This commit was created with scripts/clean-includes:
./scripts/clean-includes --git acpi include/hw/*/*acpi.h hw/*/*acpi.c
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This commit was created with scripts/clean-includes.
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This commit was created with scripts/clean-includes:
./scripts/clean-includes --git hyperv hw/hyperv/*.[ch]
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
tcg/ should not depend on accel/tcg/, but perf and debuginfo
support provided by the latter are being used by tcg/tcg.c.
Since that's the only user, move both to tcg/.
Suggested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20231212003837.64090-5-iii@linux.ibm.com>
Message-Id: <20240125054631.78867-5-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
When doing device assignment of a physical device, MSI-X can be
enabled with no vectors enabled and this sets the IRQ index to
VFIO_PCI_MSIX_IRQ_INDEX. However, when MSI-X is disabled, the IRQ
index is left untouched if no vectors are in use. Then, when INTx
is enabled, the IRQ index value is considered incompatible (set to
MSI-X) and VFIO_DEVICE_SET_IRQS fails. QEMU complains with :
qemu-system-x86_64: vfio 0000:08:00.0: Failed to set up TRIGGER eventfd signaling for interrupt INTX-0: VFIO_DEVICE_SET_IRQS failure: Invalid argument
To avoid that, unconditionaly clear the IRQ index when MSI-X is
disabled.
Buglink: https://issues.redhat.com/browse/RHEL-21293
Fixes: 5ebffa4e87 ("vfio/pci: use an invalid fd to enable MSI-X")
Cc: Jing Liu <jing2.liu@intel.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Do not use uint64_t for the type of the declaration and __u64 when
computing the number of elements in the array.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
- virtio-blk: Multiqueue fixes and cleanups
- blklogwrites: Fixes for write_zeroes and superblock update races
- commit/stream: Allow users to request only format driver names in
backing file format
- monitor: only run coroutine commands in qemu_aio_context
- Some iotest fixes
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEE3D3rFZqa+V09dFb+fwmycsiPL9YFAmWzpOwRHGt3b2xmQHJl
ZGhhdC5jb20ACgkQfwmycsiPL9ZNzg//W1+C7HxLft4Jc4O1BcOoOLlGCg4Esupt
z0/XLZ9+xVQUtjQ82pFzf9XaWQs8CuNT3FBUKi+ngdwZ0JBThIv0aGiMZBcAeQjD
qshPFgDM1lGL4ICIaT73/qfUzQgO3oruZj9F+ShBBzoasNWVoRzqqVDR3pinLwTp
D4TU+3A6LkdhlYGT60SYfRq/UKNmCA1s2wysdjqXxS6KOEURNF2VBnz0Nu76qrVb
3P/a55GPiJIn+VVsdQ0J4vyyzn23m7I7WZOJ7Sjm1EfSJ6SvcDbhWsZTUonaV2rU
qZ3WI/jggqxXRV8F2AaA4suS/Cc8RkX2KfcN8fB6wDC2eI5USSatjh6xfw5xH9Ll
NRKUO4vFFR3Lf8wN9apg0Bwxqi0GOm9kvBJT5QqjQ16R1dvqBLqbZqcx6ZXqWFXe
/Iy243Tz19mWTFVUj0EgCKQpNz9F4SyXxV83HtSR1lJ5mhthnLxkvUOe7jsFPE4d
1Z3uBNWnx2mKFkhlwocMTKayYqxPuKQ+YjqrRoplLW1GZoBeoalKRGf8/RHa6kQx
gh4cguihlb71AH1AO1QuYpiZt9G4RJR2RZlIoCPJY5TaKJedcxMVn8H+8/F0PnQd
gPysZf7hTU1xCUV6TClDd+f2fuvqZYwXdwHJ9iiohNkbFq4HFQUp4nk4/eEPGSe/
uv8oE813E30=
=KQJl
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://repo.or.cz/qemu/kevin into staging
Block layer patches
- virtio-blk: Multiqueue fixes and cleanups
- blklogwrites: Fixes for write_zeroes and superblock update races
- commit/stream: Allow users to request only format driver names in
backing file format
- monitor: only run coroutine commands in qemu_aio_context
- Some iotest fixes
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEE3D3rFZqa+V09dFb+fwmycsiPL9YFAmWzpOwRHGt3b2xmQHJl
# ZGhhdC5jb20ACgkQfwmycsiPL9ZNzg//W1+C7HxLft4Jc4O1BcOoOLlGCg4Esupt
# z0/XLZ9+xVQUtjQ82pFzf9XaWQs8CuNT3FBUKi+ngdwZ0JBThIv0aGiMZBcAeQjD
# qshPFgDM1lGL4ICIaT73/qfUzQgO3oruZj9F+ShBBzoasNWVoRzqqVDR3pinLwTp
# D4TU+3A6LkdhlYGT60SYfRq/UKNmCA1s2wysdjqXxS6KOEURNF2VBnz0Nu76qrVb
# 3P/a55GPiJIn+VVsdQ0J4vyyzn23m7I7WZOJ7Sjm1EfSJ6SvcDbhWsZTUonaV2rU
# qZ3WI/jggqxXRV8F2AaA4suS/Cc8RkX2KfcN8fB6wDC2eI5USSatjh6xfw5xH9Ll
# NRKUO4vFFR3Lf8wN9apg0Bwxqi0GOm9kvBJT5QqjQ16R1dvqBLqbZqcx6ZXqWFXe
# /Iy243Tz19mWTFVUj0EgCKQpNz9F4SyXxV83HtSR1lJ5mhthnLxkvUOe7jsFPE4d
# 1Z3uBNWnx2mKFkhlwocMTKayYqxPuKQ+YjqrRoplLW1GZoBeoalKRGf8/RHa6kQx
# gh4cguihlb71AH1AO1QuYpiZt9G4RJR2RZlIoCPJY5TaKJedcxMVn8H+8/F0PnQd
# gPysZf7hTU1xCUV6TClDd+f2fuvqZYwXdwHJ9iiohNkbFq4HFQUp4nk4/eEPGSe/
# uv8oE813E30=
# =KQJl
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 26 Jan 2024 12:26:20 GMT
# gpg: using RSA key DC3DEB159A9AF95D3D7456FE7F09B272C88F2FD6
# gpg: issuer "kwolf@redhat.com"
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* tag 'for-upstream' of https://repo.or.cz/qemu/kevin:
iotests/277: Use iotests.sock_dir for socket creation
iotests/iothreads-stream: Use the right TimeoutError
tests/unit: Bump test-replication timeout to 60 seconds
iotests/264: Use iotests.sock_dir for socket creation
block/blklogwrites: Protect mutable driver state with a mutex.
virtio-blk: always set ioeventfd during startup
virtio-blk: tolerate failure to set BlockBackend AioContext
virtio-blk: restart s->rq reqs in vq AioContexts
virtio-blk: rename dataplane to ioeventfd
virtio-blk: rename dataplane create/destroy functions
virtio-blk: move dataplane code into virtio-blk.c
monitor: only run coroutine commands in qemu_aio_context
iotests: port 141 to Python for reliable QMP testing
iotests: add filter_qmp_generated_node_ids()
stream: Allow users to request only format driver names in backing file format
commit: Allow users to request only format driver names in backing file format
string-output-visitor: Fix (pseudo) struct handling
block/blklogwrites: Fix a bug when logging "write zeroes" operations.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements a 32 half word FIFO as per imx serial device
specifications. If a non empty FIFO is below the trigger level, an
ageing timer will tick for a duration of 8 characters. On expiry,
AGTIM will be set triggering an interrupt. AGTIM timer resets when
there is activity in the receive FIFO.
Otherwise, RRDY is set when trigger level is exceeded. The receive
trigger level is 8 in newer kernel versions and 1 in older ones.
This change will break migration compatibility for the imx boards.
Signed-off-by: Rayhan Faizel <rayhan.faizel@gmail.com>
Message-id: 20240125151931.83494-1-rayhan.faizel@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: commit message tidyups]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add MMDC, OCOTP, SQPI, CAAM, and USBMISC as unimplemented devices.
This allows operating systems such as Linux to run emulations such as
mcimx6ul-evk.
Before commit 0cd4926b85 ("Refactor i.MX6UL processor code"), the affected
memory ranges were covered by the unimplemented DAP device. The commit
reduced the DAP address range from 0x100000 to 4kB, and the emulation
thus no longer covered the various unimplemented devices in the affected
address range.
Fixes: 0cd4926b85 ("Refactor i.MX6UL processor code")
Cc: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240120005356.2599547-1-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Various files in hw/arm/ don't require "cpu.h" anymore.
Except virt-acpi-build.c, all of them don't require any
ARM specific knowledge anymore and can be build once as
target agnostic units. Update meson accordingly.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-21-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move Arm A-class Generic Timer definitions to the new
"target/arm/gtimer.h" header so units in hw/ which don't
need access to ARMCPU internals can use them without
having to include the huge "cpu.h".
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-20-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARM_CPU_IRQ/FIQ definitions are used to index the GPIO
IRQ created calling qdev_init_gpio_in() in ARMCPU instance_init()
handler. To allow non-ARM code to raise interrupt on ARM cores,
move they to 'target/arm/cpu-qom.h' which is non-ARM specific and
can be included by any hw/ file.
File list to include the new header generated using:
$ git grep -wEl 'ARM_CPU_(\w*IRQ|FIQ)'
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-18-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now than we can access the M-profile bank index
definitions from the target-agnostic "cpu-qom.h"
header, we don't need the huge "cpu.h" anymore
(except in hw/arm/armv7m.c). Reduce its inclusion
to the source unit.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-17-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw/misc/xlnx-versal-crl.c doesn't require "cpu.h"
anymore. By removing it, the unit become target
agnostic: we can build it once. Update meson.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-15-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
"target/arm/cpu.h" is target specific, any file including it
becomes target specific too, thus this is the same for any file
including "hw/misc/xlnx-versal-crl.h".
"hw/misc/xlnx-versal-crl.h" doesn't require any target specific
definition however, only the target-agnostic QOM definitions
from "target/arm/cpu-qom.h". Include the latter header to avoid
tainting unnecessary objects as target-specific.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-14-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw/cpu/a9mpcore.c doesn't require "cpu.h" anymore.
By removing it, the unit become target agnostic:
we can build it once. Update meson.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-13-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Declare arm_cpu_mp_affinity() prototype in the new
"target/arm/multiprocessing.h" header so units in
hw/arm/ can use it without having to include the huge
target-specific "cpu.h".
File list to include the new header generated using:
$ git grep -lw arm_cpu_mp_affinity
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-11-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Wrapper to return the mp affinity bits from the cpu.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-10-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rename to arm_build_mp_affinity. This frees up the name for
other usage, and emphasizes that the cpu object is not involved.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-9-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw/arm/smmuv3-internal.h uses the REG32() and FIELD()
macros defined in "hw/registerfields.h". Include it in
order to avoid when refactoring unrelated headers:
In file included from ../../hw/arm/smmuv3.c:34:
hw/arm/smmuv3-internal.h:36:28: error: expected identifier
REG32(IDR0, 0x0)
^
hw/arm/smmuv3-internal.h:37:5: error: expected function body after function declarator
FIELD(IDR0, S2P, 0 , 1)
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-4-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw/arm/xilinx_zynq.c calls tswap32() which is declared
in "exec/tswap.h". Include it in order to avoid when
refactoring unrelated headers:
hw/arm/xilinx_zynq.c:103:31: error: call to undeclared function 'tswap32';
ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
board_setup_blob[n] = tswap32(board_setup_blob[n]);
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-3-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw/arm/exynos4210.c calls tswap32() which is declared
in "exec/tswap.h". Include it in order to avoid when
refactoring unrelated headers:
hw/arm/exynos4210.c:499:22: error: call to undeclared function 'tswap32';
ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
smpboot[n] = tswap32(smpboot[n]);
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-2-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add watchdog timer support to Allwinner-H40 and Bananapi.
The watchdog timer is added as an overlay to the Timer
module memory map.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Message-id: 20240115182757.1095012-4-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allwinner R40 supports an AHCI compliant SATA controller.
Add support for it.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20240115182757.1095012-3-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allwinner R40 supports two USB host ports shared between a USB 2.0 EHCI
host controller and a USB 1.1 OHCI host controller. Add support for both
of them.
If machine USB support is not enabled, create unimplemented devices
for the USB memory ranges to avoid crashes when booting Linux.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240115182757.1095012-2-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The TUSB6010 USB controller is soldered on the N800 and N810
tablets, thus is always present.
This is a migration compatibility break for the n800/n810
machines started with the '-usb none' option.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240119215106.45776-3-philmd@linaro.org
[PMM: fixed commit message typo]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The USB Controllers are part of the chipset, thus are
always present and mapped in memory.
This is a migration compatibility break for the cubieboard
machine started with the '-usb none' option.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20240119215106.45776-2-philmd@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert the musicpal key input device to use
qemu_add_kbd_event_handler(). This lets us simplify it because we no
longer need to track whether we're in the middle of a PS/2 multibyte
key sequence.
In the conversion we move the keyboard handler registration from init
to realize, because devices shouldn't disturb the state of the
simulation by doing things like registering input handlers until
they're realized, so that device objects can be introspected
safely.
The behaviour where key-repeat is permitted for the arrow-keys only
is intentional (added in commit 7c6ce4baed), so we retain it,
and add a comment to that effect.
This is a migration compatibility break for musicpal.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20231103182750.855577-1-peter.maydell@linaro.org
error_report() strings should not include trailing newlines; remove
the newline from the error we print when devices won't fit into the
address space of the CPU.
This commit also fixes the accidental hardcoded tabs that were in
this line, since we have to touch the line anyway.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240118131649.2726375-1-peter.maydell@linaro.org
When starting ioeventfd it is common practice to set the event notifier
so that the ioeventfd handler is triggered to run immediately. There may
be no requests waiting to be processed, but the idea is that if a
request snuck in then we guarantee that it will be detected.
One scenario where self-triggering the ioeventfd is necessary is when
virtio_blk_handle_output() is called from a vCPU thread before the
VIRTIO Device Status transitions to DRIVER_OK. In that case we need to
self-trigger the ioeventfd so that the kick handled by the vCPU thread
causes the vq AioContext thread to take over handling the request(s).
Fixes: b6948ab01d ("virtio-blk: add iothread-vq-mapping parameter")
Reported-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240119135748.270944-7-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We no longer rely on setting the AioContext since the block layer
IO_CODE APIs can be called from any thread. Now it's just a hint to help
block jobs and other operations co-locate themselves in a thread with
the guest I/O requests. Keep going if setting the AioContext fails.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240119135748.270944-6-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
A virtio-blk device with the iothread-vq-mapping parameter has
per-virtqueue AioContexts. It is not thread-safe to process s->rq
requests in the BlockBackend AioContext since that may be different from
the virtqueue's AioContext to which this request belongs. The code
currently races and could crash.
Adapt virtio_blk_dma_restart_cb() to first split s->rq into per-vq lists
and then schedule a BH each vq's AioContext as necessary. This way
requests are safely processed in their vq's AioContext.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240119135748.270944-5-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The dataplane code is really about using ioeventfd. It's used both for
IOThreads (what we think of as dataplane) and for the core virtio-pci
code's ioeventfd feature (which is enabled by default and used when no
IOThread has been specified). Rename the code to reflect this.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240119135748.270944-4-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
virtio_blk_data_plane_create() and virtio_blk_data_plane_destroy() are
actually about s->vq_aio_context[] rather than managing
dataplane-specific state.
As a prerequisite to using s->vq_aio_context[] in all code paths (even
when dataplane is not used), rename these functions to reflect that they
just manage s->vq_aio_context and call them regardless of whether or not
dataplane is in use.
Note that virtio-blk supports running with -device
virtio-blk-pci,ioevent=off where the vCPU thread enters the device
emulation code. In this mode ioeventfd is not used for virtqueue
processing. However, we still want to initialize s->vq_aio_context[] to
qemu_aio_context in that case since I/O completion callbacks will be
invoked in the main loop thread.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240119135748.270944-3-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
