We use 32bit value for linux,initrd-[start/end], when we have
loader_start > 4GB, there will be a wrong initrd_start passed
to the kernel, and the kernel will report the following warning.
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] initrd not fully accessible via the linear mapping -- please check your bootloader ...
[ 0.000000] WARNING: CPU: 0 PID: 0 at arch/arm64/mm/init.c:355 arm64_memblock_init+0x158/0x244
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Tainted: G W 6.1.0-rc3-13250-g30a0b95b1335-dirty #28
[ 0.000000] Hardware name: Horizon Sigi Virtual development board (DT)
[ 0.000000] pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 0.000000] pc : arm64_memblock_init+0x158/0x244
[ 0.000000] lr : arm64_memblock_init+0x158/0x244
[ 0.000000] sp : ffff800009273df0
[ 0.000000] x29: ffff800009273df0 x28: 0000001000cc0010 x27: 0000800000000000
[ 0.000000] x26: 000000000050a3e2 x25: ffff800008b46000 x24: ffff800008b46000
[ 0.000000] x23: ffff800008a53000 x22: ffff800009420000 x21: ffff800008a53000
[ 0.000000] x20: 0000000004000000 x19: 0000000004000000 x18: 00000000ffff1020
[ 0.000000] x17: 6568632065736165 x16: 6c70202d2d20676e x15: 697070616d207261
[ 0.000000] x14: 656e696c20656874 x13: 0a2e2e2e20726564 x12: 0000000000000000
[ 0.000000] x11: 0000000000000000 x10: 00000000ffffffff x9 : 0000000000000000
[ 0.000000] x8 : 0000000000000000 x7 : 796c6c756620746f x6 : 6e20647274696e69
[ 0.000000] x5 : ffff8000093c7c47 x4 : ffff800008a2102f x3 : ffff800009273a88
[ 0.000000] x2 : 80000000fffff038 x1 : 00000000000000c0 x0 : 0000000000000056
[ 0.000000] Call trace:
[ 0.000000] arm64_memblock_init+0x158/0x244
[ 0.000000] setup_arch+0x164/0x1cc
[ 0.000000] start_kernel+0x94/0x4ac
[ 0.000000] __primary_switched+0xb4/0xbc
[ 0.000000] ---[ end trace 0000000000000000 ]---
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000001000000000-0x0000001007ffffff]
This doesn't affect any machine types we currently support, because
for all of our machine types the RAM starts well below the 4GB
mark, but it does demonstrate that we're not currently writing
the device-tree properties quite as intended.
To fix it, we can change it to write these values to the dtb using a
type width matching #address-cells. This is the intended size for
these dtb properties, and is how u-boot, for instance, writes them,
although in practice the Linux kernel will cope with them being any
width as long as they're big enough to fit the value.
Signed-off-by: Schspa Shi <schspa@gmail.com>
Message-id: 20221129160724.75667-1-schspa@gmail.com
[PMM: tweaked commit message]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert the TYPE_ARM_SMMUV3 device to 3-phase reset. The legacy
reset method doesn't do anything that's invalid in the hold phase, so
the conversion only requires changing it to a hold phase method, and
using the 3-phase versions of the "save the parent reset method and
chain to it" code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221109161444.3397405-3-peter.maydell@linaro.org
Convert the TYPE_ARM_SMMU device to 3-phase reset. The legacy method
doesn't do anything that's invalid in the hold phase, so the
conversion is simple and not a behaviour change.
Note that we must convert this base class before we can convert the
TYPE_ARM_SMMUV3 subclass -- transitional support in Resettable
handles "chain to parent class reset" when the base class is 3-phase
and the subclass is still using legacy reset, but not the other way
around.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20221109161444.3397405-2-peter.maydell@linaro.org
The Cortex-A55 is one of the newer armv8.2+ CPUs; in particular
it supports the Privileged Access Never (PAN) feature. Add
a model of this CPU, so you can use a CPU type on the virt
board that models a specific real hardware CPU, rather than
having to use the QEMU-specific "max" CPU type.
Signed-off-by: Timofey Kutergin <tkutergin@gmail.com>
Message-id: 20221121150819.2782817-1-tkutergin@gmail.com
[PMM: tweaked commit message]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use the base_memmap to build the SMBIOS 19 table which provides the address
mapping for a Physical Memory Array (from spec [1] chapter 7.20).
This was present on i386 from commit c97294ec1b
("SMBIOS: Build aggregate smbios tables and entry point").
[1] https://www.dmtf.org/sites/default/files/standards/documents/DSP0134_3.5.0.pdf
The absence of this table is a breach of the specs and is
detected by the FirmwareTestSuite (FWTS), but it doesn't
cause any known problems for guest OSes.
Signed-off-by: Mihai Carabas <mihai.carabas@oracle.com>
Message-id: 1668789029-5432-1-git-send-email-mihai.carabas@oracle.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 3 high memory regions are usually enabled by default, but they may
be not used. For example, VIRT_HIGH_GIC_REDIST2 isn't needed by GICv2.
This leads to waste in the PA space.
Add properties ("highmem-redists", "highmem-ecam", "highmem-mmio") to
allow users selectively disable them if needed. After that, the high
memory region for GICv3 or GICv4 redistributor can be disabled by user,
the number of maximal supported CPUs needs to be calculated based on
'vms->highmem_redists'. The follow-up error message is also improved
to indicate if the high memory region for GICv3 and GICv4 has been
enabled or not.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20221029224307.138822-8-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
After the improvement to high memory region address assignment is
applied, the memory layout can be changed, introducing possible
migration breakage. For example, VIRT_HIGH_PCIE_MMIO memory region
is disabled or enabled when the optimization is applied or not, with
the following configuration. The configuration is only achievable by
modifying the source code until more properties are added to allow
users selectively disable those high memory regions.
pa_bits = 40;
vms->highmem_redists = false;
vms->highmem_ecam = false;
vms->highmem_mmio = true;
# qemu-system-aarch64 -accel kvm -cpu host \
-machine virt-7.2,compact-highmem={on, off} \
-m 4G,maxmem=511G -monitor stdio
Region compact-highmem=off compact-highmem=on
----------------------------------------------------------------
MEM [1GB 512GB] [1GB 512GB]
HIGH_GIC_REDISTS2 [512GB 512GB+64MB] [disabled]
HIGH_PCIE_ECAM [512GB+256MB 512GB+512MB] [disabled]
HIGH_PCIE_MMIO [disabled] [512GB 1TB]
In order to keep backwords compatibility, we need to disable the
optimization on machine, which is virt-7.1 or ealier than it. It
means the optimization is enabled by default from virt-7.2. Besides,
'compact-highmem' property is added so that the optimization can be
explicitly enabled or disabled on all machine types by users.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-id: 20221029224307.138822-7-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are three high memory regions, which are VIRT_HIGH_REDIST2,
VIRT_HIGH_PCIE_ECAM and VIRT_HIGH_PCIE_MMIO. Their base addresses
are floating on highest RAM address. However, they can be disabled
in several cases.
(1) One specific high memory region is likely to be disabled by
code by toggling vms->highmem_{redists, ecam, mmio}.
(2) VIRT_HIGH_PCIE_ECAM region is disabled on machine, which is
'virt-2.12' or ealier than it.
(3) VIRT_HIGH_PCIE_ECAM region is disabled when firmware is loaded
on 32-bits system.
(4) One specific high memory region is disabled when it breaks the
PA space limit.
The current implementation of virt_set_{memmap, high_memmap}() isn't
optimized because the high memory region's PA space is always reserved,
regardless of whatever the actual state in the corresponding
vms->highmem_{redists, ecam, mmio} flag. In the code, 'base' and
'vms->highest_gpa' are always increased for case (1), (2) and (3).
It's unnecessary since the assigned PA space for the disabled high
memory region won't be used afterwards.
Improve the address assignment for those three high memory region by
skipping the address assignment for one specific high memory region if
it has been disabled in case (1), (2) and (3). The memory layout may
be changed after the improvement is applied, which leads to potential
migration breakage. So 'vms->highmem_compact' is added to control if
the improvement should be applied. For now, 'vms->highmem_compact' is
set to false, meaning that we don't have memory layout change until it
becomes configurable through property 'compact-highmem' in next patch.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-id: 20221029224307.138822-6-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This introduces virt_get_high_memmap_enabled() helper, which returns
the pointer to vms->highmem_{redists, ecam, mmio}. The pointer will
be used in the subsequent patches.
No functional change intended.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-id: 20221029224307.138822-5-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This introduces variable 'region_base' for the base address of the
specific high memory region. It's the preparatory work to optimize
high memory region address assignment.
No functional change intended.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-id: 20221029224307.138822-4-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This renames variable 'size' to 'region_size' in virt_set_high_memmap().
Its counterpart ('region_base') will be introduced in next patch.
No functional change intended.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-id: 20221029224307.138822-3-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This introduces virt_set_high_memmap() helper. The logic of high
memory region address assignment is moved to the helper. The intention
is to make the subsequent optimization for high memory region address
assignment easier.
No functional change intended.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-id: 20221029224307.138822-2-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
lots of acpi rework
first version of biosbits infrastructure
ASID support in vhost-vdpa
core_count2 support in smbios
PCIe DOE emulation
virtio vq reset
HMAT support
part of infrastructure for viommu support in vhost-vdpa
VTD PASID support
fixes, tests all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmNpXDkPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpD0AH/2G8ZPrgrxJC9y3uD5/5J6QRzO+TsDYbg5ut
uBf4rKSHHzcu6zdyAfsrhbAKKzyD4HrEGNXZrBjnKM1xCiB/SGBcDIWntwrca2+s
5Dpbi4xvd4tg6tVD4b47XNDCcn2uUbeI0e2M5QIbtCmzdi/xKbFAfl5G8DQp431X
Kmz79G4CdKWyjVlM0HoYmdCw/4FxkdjD02tE/Uc5YMrePNaEg5Bw4hjCHbx1b6ur
6gjeXAtncm9s4sO0l+sIdyiqlxiTry9FSr35WaQ0qPU+Og5zaf1EiWfdl8TRo4qU
EAATw5A4hyw11GfOGp7oOVkTGvcNB/H7aIxD7emdWZV8+BMRPKo=
=zTCn
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
pci,pc,virtio: features, tests, fixes, cleanups
lots of acpi rework
first version of biosbits infrastructure
ASID support in vhost-vdpa
core_count2 support in smbios
PCIe DOE emulation
virtio vq reset
HMAT support
part of infrastructure for viommu support in vhost-vdpa
VTD PASID support
fixes, tests all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmNpXDkPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRpD0AH/2G8ZPrgrxJC9y3uD5/5J6QRzO+TsDYbg5ut
# uBf4rKSHHzcu6zdyAfsrhbAKKzyD4HrEGNXZrBjnKM1xCiB/SGBcDIWntwrca2+s
# 5Dpbi4xvd4tg6tVD4b47XNDCcn2uUbeI0e2M5QIbtCmzdi/xKbFAfl5G8DQp431X
# Kmz79G4CdKWyjVlM0HoYmdCw/4FxkdjD02tE/Uc5YMrePNaEg5Bw4hjCHbx1b6ur
# 6gjeXAtncm9s4sO0l+sIdyiqlxiTry9FSr35WaQ0qPU+Og5zaf1EiWfdl8TRo4qU
# EAATw5A4hyw11GfOGp7oOVkTGvcNB/H7aIxD7emdWZV8+BMRPKo=
# =zTCn
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 07 Nov 2022 14:27:53 EST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (83 commits)
checkpatch: better pattern for inline comments
hw/virtio: introduce virtio_device_should_start
tests/acpi: update tables for new core count test
bios-tables-test: add test for number of cores > 255
tests/acpi: allow changes for core_count2 test
bios-tables-test: teach test to use smbios 3.0 tables
hw/smbios: add core_count2 to smbios table type 4
vhost-user: Support vhost_dev_start
vhost: Change the sequence of device start
intel-iommu: PASID support
intel-iommu: convert VTD_PE_GET_FPD_ERR() to be a function
intel-iommu: drop VTDBus
intel-iommu: don't warn guest errors when getting rid2pasid entry
vfio: move implement of vfio_get_xlat_addr() to memory.c
tests: virt: Update expected *.acpihmatvirt tables
tests: acpi: aarch64/virt: add a test for hmat nodes with no initiators
hw/arm/virt: Enable HMAT on arm virt machine
tests: Add HMAT AArch64/virt empty table files
tests: acpi: q35: update expected blobs *.hmat-noinitiators expected HMAT:
tests: acpi: q35: add test for hmat nodes without initiators
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Since the patchset ("Build ACPI Heterogeneous Memory Attribute Table (HMAT)"),
HMAT is supported, but only x86 is enabled. Enable HMAT on arm virt machine.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Hesham Almatary <hesham.almatary@huawei.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20221027100037.251-7-hesham.almatary@huawei.com>
Tested-by: Yicong Yang <yangyicong@hisilicon.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
MADT has been updated with the GIC Structures from ACPI 6.0 Errata A
and so MADT revision and GICC Structure must be updated also.
Fixes: 37f33084ed ("acpi: arm/virt: madt: use build_append_int_noprefix() API to compose MADT table")
Signed-off-by: Miguel Luis <miguel.luis@oracle.com>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Message-Id: <20221011181730.10885-4-miguel.luis@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Update the Fixed ACPI Description Table (FADT) to revision 6.0 of the ACPI
specification adding the field "Hypervisor Vendor Identity".
This field's description states the following: "64-bit identifier of hypervisor
vendor. All bytes in this field are considered part of the vendor identity.
These identifiers are defined independently by the vendors themselves,
usually following the name of the hypervisor product. Version information
should NOT be included in this field - this shall simply denote the vendor's
name or identifier. Version information can be communicated through a
supplemental vendor-specific hypervisor API. Firmware implementers would
place zero bytes into this field, denoting that no hypervisor is present in
the actual firmware."
Signed-off-by: Miguel Luis <miguel.luis@oracle.com>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Message-Id: <20221011181730.10885-3-miguel.luis@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When we direct boot a kernel on a CPU which emulates EL3, we need to
set up the EL3 system registers as the Linux kernel documentation
specifies:
https://www.kernel.org/doc/Documentation/arm64/booting.rst
For CPUs with FEAT_HCX support this includes:
- SCR_EL3.HXEn (bit 38) must be initialised to 0b1.
but we forgot to do this when implementing FEAT_HCX, which would mean
that a guest trying to access the HCRX_EL2 register would crash.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221027140207.413084-3-peter.maydell@linaro.org
When we direct boot a kernel on a CPU which emulates EL3, we need
to set up the EL3 system registers as the Linux kernel documentation
specifies:
https://www.kernel.org/doc/Documentation/arm64/booting.rst
For SVE and SME this includes:
- ZCR_EL3.LEN must be initialised to the same value for all CPUs the
kernel is executed on.
- SMCR_EL3.LEN must be initialised to the same value for all CPUs the
kernel will execute on.
Although we are technically compliant with this, the "same value" we
currently use by default is the reset value of 0. This will end up
forcing the guest kernel's SVE and SME vector length to be only the
smallest supported length.
Initialize the vector length fields to their maximum possible value,
which is 0xf. If the implementation doesn't actually support that
vector length then the effective vector length will be constrained
down to the maximum supported value at point of use.
This allows the guest to use all the vector lengths the emulated CPU
supports (by programming the _EL2 and _EL1 versions of these
registers.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221027140207.413084-2-peter.maydell@linaro.org
When the system reboots, the rng-seed that the FDT has should be
re-randomized, so that the new boot gets a new seed. Since the FDT is in
the ROM region at this point, we add a hook right after the ROM has been
added, so that we have a pointer to that copy of the FDT.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Message-id: 20221025004327.568476-5-Jason@zx2c4.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Snapshot loading only expects to call deterministic handlers, not
non-deterministic ones. So introduce a way of registering handlers that
won't be called when reseting for snapshots.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Message-id: 20221025004327.568476-2-Jason@zx2c4.com
[PMM: updated json doc comment with Markus' text; fixed
checkpatch style nit]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The "PCI Bus Binding to: IEEE Std 1275-1994" defines the compatible
string for a PCIe bus or endpoint as "pci<vendorid>,<deviceid>" or
similar. Since the initial binding for PCI virtio-iommu didn't follow
this rule, it was modified to accept both strings and ensure backward
compatibility. Also, the unit-name for the node should be
"device,function".
Fix corresponding dt-validate and dtc warnings:
pcie@10000000: virtio_iommu@16:compatible: ['virtio,pci-iommu'] does not contain items matching the given schema
pcie@10000000: Unevaluated properties are not allowed (... 'virtio_iommu@16' were unexpected)
From schema: linux/Documentation/devicetree/bindings/pci/host-generic-pci.yaml
virtio_iommu@16: compatible: 'oneOf' conditional failed, one must be fixed:
['virtio,pci-iommu'] is too short
'pci1af4,1057' was expected
From schema: dtschema/schemas/pci/pci-bus.yaml
Warning (pci_device_reg): /pcie@10000000/virtio_iommu@16: PCI unit address format error, expected "2,0"
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Performance improvement with Object class caching
* Serial Flash Discovery Parameters support for m25p80 device
* Various small adjustments on intructions and models
-----BEGIN PGP SIGNATURE-----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=u7pS
-----END PGP SIGNATURE-----
Merge tag 'pull-aspeed-20221025' of https://github.com/legoater/qemu into staging
aspeed queue :
* Performance improvement with Object class caching
* Serial Flash Discovery Parameters support for m25p80 device
* Various small adjustments on intructions and models
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmNX/WEACgkQUaNDx8/7
# 7KFhERAAhrcLcv15ny8RwatHPjzU00ZPQ0PcxGj1VDT66pCVh6M+rIeRPB2scOey
# Pu8jUvIYJ8w7ozjAP6YTQ1MP/WufniVi91Bx+vs/okSiWZa4dP0/G7NQWoc1at0s
# NBlkg57l1GMEeQb5x8vC1DizTQ1Z8Q8J/Ur3uXukXCmYVJAwHYpl/Foob1IPFgh8
# UcJ55LyuRq99lS8ib6HvRftAsC3DOcA/sl3b/TYR2+iKyi1VS2aZoQzxVCavSBcz
# PoTonT9O4OvIQthAgXRwpylW/aMYU3I7FeyOMKlCNLbmJ8LpVbX2v0KN3WBvWBv4
# OWP0DiqPUuoWFHLUGKbiVOgWQrTQXZyoD70SD/ObE1oMTLmeBoD1oFizQDvokHAR
# g2+gMdWnuWcbyaofY7YwuI6qz22gbrgh8JqX6sEWRDnY7HgCUvPhCsmci+bdN5cf
# dGcE8YKi7aD5gzoU9LRziPlhbwaEsgYLpYS7aGfNcmypgeq6lmNG7xKyw911zCTY
# uqDZWOUJy0tUIUTxoz3o1/KtsTFugjuZ+9W1SxELptJR37iwlP1vumf6bduwcx/3
# ba8tzNoXecXO5Icmq5P3lMNVM/abpkDDKS66HA87mABLEd/eCD0ojR9Kfxo0mD74
# kmQK3MFfJPkTu0ddu1cWhCIgTO7EuLuZL7gzj1oxoeXiU3YcVh8=
# =u7pS
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 25 Oct 2022 11:14:41 EDT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-aspeed-20221025' of https://github.com/legoater/qemu:
arm/aspeed: Replace mx25l25635e chip model
m25p80: Add the w25q01jvq SFPD table
m25p80: Add the w25q512jv SFPD table
m25p80: Add the w25q256 SFPD table
m25p80: Add the mx66l1g45g SFDP table
m25p80: Add the mx25l25635f SFPD table
m25p80: Add the mx25l25635e SFPD table
m25p80: Add erase size for mx25l25635e
m25p80: Add the n25q256a SFDP table
m25p80: Add basic support for the SFDP command
hw/arm/aspeed: increase Bletchley memory size
ast2600: Drop NEON from the CPU features
aspeed/smc: Cache AspeedSMCClass
ssi: cache SSIPeripheralClass to avoid GET_CLASS()
tests/avocado/machine_aspeed.py: Fix typos on buildroot
hw/i2c/aspeed: Fix old reg slave receive
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
A mx25l25635f chip model is generally found on these machines. It's
newer and uses 4B opcodes which is better to exercise the support in
the Linux kernel.
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-Id: <20220722063602.128144-9-clg@kaod.org>
Message-Id: <20221013161241.2805140-11-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
For the PVT-class hardware we have increased the memory size of
this device to 2 GiB. Adjust the device model accordingly.
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20221007110529.3657749-1-patrick@stwcx.xyz>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Currently, the CPU features exposed to the AST2600 QEMU machines are :
half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt
vfpd32 lpae evtstrm
But, the features of the Cortex A7 CPU on the Aspeed AST2600 A3 SoC
are :
half thumb fastmult vfp edsp vfpv3 vfpv3d16 tls vfpv4 idiva idivt
lpae evtstrm
Drop NEON support in the Aspeed AST2600 SoC.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20220928164719.655586-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
These memory allocation functions return void *, and casting to
another pointer type is useless clutter. Drop these casts.
If you really want another pointer type, consider g_new().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220923120025.448759-3-armbru@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
load_image_to_fw_cfg() is duplicated by both arm and loongarch. The same
function will be required by riscv too. So, it's time to refactor and
move this function to a common path.
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20221004092351.18209-2-sunilvl@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Per the ACPI 6.5 specification, on the GTDT Table Structure, the Counter Control
Block Address and Counter Read Block Address fields of the GTDT table should be
set to 0xFFFFFFFFFFFFFFFF if not provided, rather than 0x0.
Fixes: 41041e5708 ("acpi: arm/virt: build_gtdt: use acpi_table_begin()/acpi_table_end() instead of build_header()")
Signed-off-by: Miguel Luis <miguel.luis@oracle.com>
Message-Id: <20220920162137.75239-3-miguel.luis@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
The SMMUv3 node isn't expected to have clock properties
(unlike the SMMUv2). Fix the corresponding dt-validate warning:
smmuv3@9050000: 'clock-names', 'clocks' do not match any of the regexes: 'pinctrl-[0-9]+'
From schema: linux/Documentation/devicetree/bindings/iommu/arm,smmu-v3.yaml
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: tweaked commit message as suggested by Eric]
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220927100347.176606-7-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The "msi-parent" property can be used on the PCI node when MSIs do not
contain sideband data (device IDs) [1]. In QEMU, MSI transactions
contain the requester ID, so the PCI node should use the "msi-map"
property instead of "msi-parent". In our case the property describes an
identity map between requester ID and sideband data.
This fixes a warning when passing the DTB generated by QEMU to dtc,
following a recent change to the GICv3 node:
Warning (msi_parent_property): /pcie@10000000:msi-parent: property size (4) too small for cell size 1
[1] linux/Documentation/devicetree/bindings/pci/pci-msi.txt
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220927100347.176606-4-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GICv3 bindings requires a #msi-cells property for the ITS node. Fix
the corresponding dt-validate warning:
interrupt-controller@8000000: msi-controller@8080000: '#msi-cells' is a required property
From schema: linux/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.yaml
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220927100347.176606-3-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The devicetree specification requires a 'model' property in the root
node. Fix the corresponding dt-validate warning:
/: 'model' is a required property
From schema: dtschema/schemas/root-node.yaml
Use the same name for model as for compatible. The specification
recommends that 'compatible' follows the format 'manufacturer,model' and
'model' follows the format 'manufacturer,model-number'. Since our
'compatible' doesn't observe this, 'model' doesn't really need to
either.
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220927100347.176606-2-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect ZynqMP's USB controllers.
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20220920081517.25401-1-frasse.iglesias@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently armv7m_load_kernel() takes the size of the block of memory
where it should load the initial guest image, but assumes that it
should always load it at address 0. This happens to be true of all
our M-profile boards at the moment, but it isn't guaranteed to always
be so: M-profile CPUs can be configured (via init-svtor and
init-nsvtor, which match equivalent hardware configuration signals)
to have the initial vector table at any address, not just zero. (For
instance the Teeny board has the boot ROM at address 0x0200_0000.)
Add a base address argument to armv7m_load_kernel(), so that
callers now pass in both base address and size. All the current
callers pass 0, so this is not a behaviour change.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220823160417.3858216-3-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Arm system emulation targets always have TARGET_BIG_ENDIAN clear, so
there is no need to have handling in armv7m_load_kernel() for the
case when it is defined. Remove the unnecessary code.
Side notes:
* our M-profile implementation is always little-endian (that is, it
makes the IMPDEF choice that the read-only AIRCR.ENDIANNESS is 0)
* if we did want to handle big-endian ELF files here we should do it
the way that hw/arm/boot.c:arm_load_elf() does, by looking at the
ELF header to see what endianness the file itself is
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220823160417.3858216-2-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add cortex A35 core and enable it for virt board.
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Joe Komlodi <komlodi@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220819002015.1663247-1-wuhaotsh@google.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
With the introduction of the new TCG GICv4, build_madt() is badly broken
as we do not present any GIC Redistributor structure in MADT for GICv4
guests, so that they have no idea about where the Redistributor
register frames are. This fixes a Linux guest crash at boot time with
ACPI enabled and '-machine gic-version=4'.
While at it, let's convert the remaining hard coded gic_version into
enumeration VIRT_GIC_VERSION_2 for consistency.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Message-id: 20220812022018.1069-1-yuzenghui@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Fix ownership of RAM regions on the fby35 machine
-----BEGIN PGP SIGNATURE-----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=hAJg
-----END PGP SIGNATURE-----
Merge tag 'pull-aspeed-20220801' of https://github.com/legoater/qemu into staging
aspeed queue:
* Fix ownership of RAM regions on the fby35 machine
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmLn1N8ACgkQUaNDx8/7
# 7KHaVA//eh5wIZKeg1Qit8dhVoPXcO7b97KFpBreyCkfdREJpoLjoFe4y+rnKhnL
# tJm6qx1YG5s0UN/ODcy4TyKV9CkpcjsRZ+BHuZ+jjiz3WzuarZUTbZx1jVSJP6z0
# xcXc3CucKe/yyidGV1gKGiWetuXv2F6nYHzfvJ4auei6Rga8rwmiN7Rqf3Qfh6Lw
# Islj/9axfLxGzuMV85uuRZdRrrlmTOjDgnF4mxwVXRrxjtLIaAbzKT6mc1p1FUry
# cuE7bDjbZoT7ftBn5y4gQXV38M3XcWzB1KvzMslldkccU7cTbJg8620KSNiscOkJ
# 03xEJiBJoAzy/X1PUmEODNYUV8a19xcsXEyqaRQiyYtO1XMBDcNkSaiaFacOnhFT
# UxabJf3qvzf1QwAmgxGUdbR5usNXsr8Yrnpf1lew7Mvr3SwOYVXqb/JPp+j7uoV3
# CVvvTFZm+hBQghaHC0wHBX+C3aLsTis4Jppn5loulo6fb9KZiosj2kPRwEIetVkt
# ZgkBOLWRWtizdWKM7HImt7F+v/r7ClFlwAIJj8QQV0HTtVZ+gM6MXWj5oczKENJ8
# vPkoP6AUoOWzKFEhBU5XtQ9DdwPSP9m6zAZXl4LD17tVPUPpsuSEDaxhH5hAEnIR
# 39Mgx7hoK0uLHhM02RrNodD/NDmrZCPV3PwZ979z0Q/C8dttRkY=
# =hAJg
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 01 Aug 2022 06:27:59 AM PDT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-aspeed-20220801' of https://github.com/legoater/qemu:
aspeed/fby35: Fix owner of the BMC RAM memory region
aspeed: Remove unused fields from AspeedMachineState
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
A MachineState object is used as a owner of the RAM region and this
asserts in memory_region_init_ram() when QEMU is built with
CONFIG_QOM_CAST_DEBUG :
/* This will assert if owner is neither NULL nor a DeviceState.
* We only want the owner here for the purposes of defining a
* unique name for migration. TODO: Ideally we should implement
* a naming scheme for Objects which are not DeviceStates, in
* which case we can relax this restriction.
*/
owner_dev = DEVICE(owner);
Use the BMC and BIC objects as the owners of their memory regions.
Cc: Peter Delevoryas <peter@pjd.dev>
Fixes: 778e14cc5c ("aspeed: Add AST2600 (BMC) to fby35")
Reviewed-by: Peter Delevoryas <peter@pjd.dev>
Message-Id: <20220727102714.803041-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Fixes: 346160cbf2 ("aspeed: Set the dram container at the SoC level")
Message-Id: <20220727102714.803041-2-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Some files wrongly contain the same word twice in a row.
One of them should be removed or replaced.
Message-Id: <20220722145859.1952732-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is nothing in the specs on DMA engine interrupt lines: it should have
been in the "BCM2835 ARM Peripherals" datasheet but the appropriate
"ARM peripherals interrupt table" (p.113) is nearly empty.
All Raspberry Pi models 1-3 (based on bcm2835) have
Linux device tree (arch/arm/boot/dts/bcm2835-common.dtsi +25):
/* dma channel 11-14 share one irq */
This information is repeated in the driver code
(drivers/dma/bcm2835-dma.c +1344):
/*
* in case of channel >= 11
* use the 11th interrupt and that is shared
*/
In this patch channels 0--10 and 11--14 are handled separately.
Signed-off-by: Andrey Makarov <andrey.makarov@auriga.com>
Message-id: 20220716113210.349153-1-andrey.makarov@auriga.com
[PMM: fixed checkpatch nits]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With the BIC, the easiest way to run everything is to create two pty's
for each SoC and reserve stdin/stdout for the monitor:
wget https://github.com/facebook/openbmc/releases/download/openbmc-e2294ff5d31d/fby35.mtd
wget https://github.com/peterdelevoryas/OpenBIC/releases/download/oby35-cl-2022.13.01/Y35BCL.elf
qemu-system-arm -machine fby35 \
-drive file=fby35.mtd,format=raw,if=mtd \
-device loader,file=fby35.mtd,addr=0,cpu-num=0 \
-serial pty -serial pty -serial mon:stdio -display none -S
screen /dev/ttys0
screen /dev/ttys1
(qemu) c
This commit only adds the the first server board's Bridge IC, but in the
future we'll try to include the other three server board Bridge IC's
too.
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220705191400.41632-9-peter@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The BMC boots from the first flash device by fetching instructions
from the flash contents. Add an alias region on 0x0 for this
purpose. There are currently performance issues with this method (TBs
being flushed too often), so as a faster alternative, install the
flash contents as a ROM in the BMC memory space.
See commit 1a15311a12 ("hw/arm/aspeed: add a 'execute-in-place'
property to boot directly from CE0")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
[ clg: blk_pread() fixes ]
Message-Id: <20220705191400.41632-8-peter@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
You can test booting the BMC with both '-device loader' and '-drive
file'. This is necessary because of how the fb-openbmc boot sequence
works (jump to 0x20000000 after U-Boot SPL).
wget https://github.com/facebook/openbmc/releases/download/openbmc-e2294ff5d31d/fby35.mtd
qemu-system-arm -machine fby35 -nographic \
-device loader,file=fby35.mtd,addr=0,cpu-num=0 -drive file=fby35.mtd,format=raw,if=mtd
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220705191400.41632-7-peter@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
