We use 32bit value for linux,initrd-[start/end], when we have
loader_start > 4GB, there will be a wrong initrd_start passed
to the kernel, and the kernel will report the following warning.
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] initrd not fully accessible via the linear mapping -- please check your bootloader ...
[ 0.000000] WARNING: CPU: 0 PID: 0 at arch/arm64/mm/init.c:355 arm64_memblock_init+0x158/0x244
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Tainted: G W 6.1.0-rc3-13250-g30a0b95b1335-dirty #28
[ 0.000000] Hardware name: Horizon Sigi Virtual development board (DT)
[ 0.000000] pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 0.000000] pc : arm64_memblock_init+0x158/0x244
[ 0.000000] lr : arm64_memblock_init+0x158/0x244
[ 0.000000] sp : ffff800009273df0
[ 0.000000] x29: ffff800009273df0 x28: 0000001000cc0010 x27: 0000800000000000
[ 0.000000] x26: 000000000050a3e2 x25: ffff800008b46000 x24: ffff800008b46000
[ 0.000000] x23: ffff800008a53000 x22: ffff800009420000 x21: ffff800008a53000
[ 0.000000] x20: 0000000004000000 x19: 0000000004000000 x18: 00000000ffff1020
[ 0.000000] x17: 6568632065736165 x16: 6c70202d2d20676e x15: 697070616d207261
[ 0.000000] x14: 656e696c20656874 x13: 0a2e2e2e20726564 x12: 0000000000000000
[ 0.000000] x11: 0000000000000000 x10: 00000000ffffffff x9 : 0000000000000000
[ 0.000000] x8 : 0000000000000000 x7 : 796c6c756620746f x6 : 6e20647274696e69
[ 0.000000] x5 : ffff8000093c7c47 x4 : ffff800008a2102f x3 : ffff800009273a88
[ 0.000000] x2 : 80000000fffff038 x1 : 00000000000000c0 x0 : 0000000000000056
[ 0.000000] Call trace:
[ 0.000000] arm64_memblock_init+0x158/0x244
[ 0.000000] setup_arch+0x164/0x1cc
[ 0.000000] start_kernel+0x94/0x4ac
[ 0.000000] __primary_switched+0xb4/0xbc
[ 0.000000] ---[ end trace 0000000000000000 ]---
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000001000000000-0x0000001007ffffff]
This doesn't affect any machine types we currently support, because
for all of our machine types the RAM starts well below the 4GB
mark, but it does demonstrate that we're not currently writing
the device-tree properties quite as intended.
To fix it, we can change it to write these values to the dtb using a
type width matching #address-cells. This is the intended size for
these dtb properties, and is how u-boot, for instance, writes them,
although in practice the Linux kernel will cope with them being any
width as long as they're big enough to fit the value.
Signed-off-by: Schspa Shi <schspa@gmail.com>
Message-id: 20221129160724.75667-1-schspa@gmail.com
[PMM: tweaked commit message]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
990f49cfd7