For long-term distributions that release a new version only very
seldom, we limit the support to five years after the initial release.
Otherwise, we might need to support distros like openSUSE 15 for
up to 7 or even more years in total due to our "two more years
after the next major release" rule, which is just way too much to
handle in a project like QEMU that only has limited human resources.
Message-Id: <20230223193257.1068205-1-thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Allwinner h3 has 4 twi(i2c) devices named twi0, twi1, twi2 and r_twi.
The registers are compatible with TYPE_AW_I2C_SUN6I, write 1 to clear
control register's INT_FLAG bit.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add emulation of TP4146 ("Flexible Data Placement").
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jesper Devantier <j.devantier@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add support for the Directive Send and Recv commands and the Identify
directive.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add the mandatory Endurance Group identify data structures and log
pages.
For now, all namespaces in a subsystem belongs to a single Endurance
Group.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Each NvmeNamespace can be used by serveral controllers,
but a NvmeNamespace can at most belong to a single NvmeSubsystem.
Store a pointer to the NvmeSubsystem, if the namespace was realized
with a NvmeSubsystem.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Move the rounding of bytes read/written into nvme_smart_log which
reports in units of 512 bytes, rounded up in thousands. This is in
preparation for adding the Endurance Group Information log page which
reports in units of billions, rounded up.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Joel Granados <j.granados@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Fedora 39 will ship its arm64 kernels in the new generic EFI zboot
format, using gzip compression for the payload.
For doing EFI boot in QEMU, this is completely transparent, as the
firmware or bootloader will take care of this. However, for direct
kernel boot without firmware, we will lose the ability to boot such
distro kernels unless we deal with the new format directly.
EFI zboot images contain metadata in the header regarding the placement
of the compressed payload inside the image, and the type of compression
used. This means we can wire up the existing gzip support without too
much hassle, by parsing the header and grabbing the payload from inside
the loaded zboot image.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Alex Bennée <alex.bennee@linaro.org>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Message-id: 20230303160109.3626966-1-ardb@kernel.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: tweaked comment formatting, fixed checkpatch nits]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Integrate neighboring code from get_phys_addr_lpae which computed
starting level, as it is easier to validate when doing both at the
same time. Mirror the checks at the start of AArch{64,32}.S2Walk,
especially S2InvalidSL and S2InconsistentSL.
This reverts 49ba115bb7, which was incorrect -- there is nothing
in the ARM pseudocode that depends on TxSZ, i.e. outputsize; the
pseudocode is consistent in referencing PAMax.
Fixes: 49ba115bb7 ("target/arm: Pass outputsize down to check_s2_mmu_setup")
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230227225832.816605-5-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In several places we use arm_is_secure_below_el3 and
arm_is_el3_or_mon separately from arm_is_secure.
These functions make no sense for m-profile, and
would indicate prior incorrect feature testing.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230227225832.816605-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
M-profile doesn't have HCR_EL2. While we could test features
before each call, zero is a generally safe return value to
disable the code in the caller. This test is required to
avoid an assert in arm_is_secure_below_el3.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230227225832.816605-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The upstream gdb xml only implements {MSP,PSP}{,_NS,S}, but
go ahead and implement the other system registers as well.
Since there is significant overlap between the two, implement
them with common code. The only exception is the systemreg
view of CONTROL, which merges the banked bits as per MRS.
Signed-off-by: David Reiss <dreiss@meta.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230227213329.793795-15-richard.henderson@linaro.org
[rth: Substatial rewrite using enumerator and shared code.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow the function to be used outside of m_helper.c.
Move to be outside of ifndef CONFIG_USER_ONLY block.
Rename from get_v7m_sp_ptr.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: David Reiss <dreiss@meta.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230227213329.793795-14-richard.henderson@linaro.org
[rth: Split out of a larger patch]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow the function to be used outside of m_helper.c.
Rename with an "arm_" prefix.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: David Reiss <dreiss@meta.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230227213329.793795-13-richard.henderson@linaro.org
[rth: Split out of a larger patch]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The extension is primarily defined by the Linux kernel NT_ARM_PAC_MASK
ptrace register set.
The original gdb feature consists of two masks, data and code, which are
used to mask out the authentication code within a pointer. Following
discussion with Luis Machado, add two more masks in order to support
pointers within the high half of the address space (i.e. TTBR1 vs TTBR0).
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1105
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230227213329.793795-12-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Keep the logic for pauth within pauth_helper.c, and expose
a helper function for use with the gdbstub pac extension.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230227213329.793795-11-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Order suf[] by the log8 of the width.
Use ARRAY_SIZE instead of hard-coding 128.
This changes the order of the union definitions,
but retains the order of the union-of-union members.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230227213329.793795-10-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will make the function usable between SVE and SME.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230227213329.793795-9-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Define svep based on the size of the predicates,
not the primary vector registers.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230227213329.793795-8-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rather than increment base_reg and num, compute num from the change
to base_reg at the end. Clean up some nearby comments.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230227213329.793795-6-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create a subroutine for creating the union of unions
of the various type sizes that a vector may contain.
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230227213329.793795-5-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The function is only used for aarch64, so move it to the
file that has the other aarch64 gdbstub stuff. Move the
declaration to internals.h.
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230227213329.793795-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This function is not used outside gdbstub.c.
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230227213329.793795-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make the form of the function names between fp and sve the same:
- arm_gdb_*_svereg -> aarch64_gdb_*_sve_reg.
- aarch64_fpu_gdb_*_reg -> aarch64_gdb_*_fpu_reg.
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230227213329.793795-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
xen_pt_config_reg_init() reads only that many bytes as the size of the
register that is being initialized. It uses
xen_host_pci_get_{byte,word,long} and casts its last argument to
expected pointer type. This means for smaller registers higher bits of
'val' are not initialized. Then, the function fails if any of those
higher bits are set.
Fix this by initializing 'val' with zero.
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Message-Id: <20230127050815.4155276-1-marmarek@invisiblethingslab.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Intel specifies that the Intel IGD must occupy slot 2 on the PCI bus,
as noted in docs/igd-assign.txt in the Qemu source code.
Currently, when the xl toolstack is used to configure a Xen HVM guest with
Intel IGD passthrough to the guest with the Qemu upstream device model,
a Qemu emulated PCI device will occupy slot 2 and the Intel IGD will occupy
a different slot. This problem often prevents the guest from booting.
The only available workarounds are not good: Configure Xen HVM guests to
use the old and no longer maintained Qemu traditional device model
available from xenbits.xen.org which does reserve slot 2 for the Intel
IGD or use the "pc" machine type instead of the "xenfv" machine type and
add the xen platform device at slot 3 using a command line option
instead of patching qemu to fix the "xenfv" machine type directly. The
second workaround causes some degredation in startup performance such as
a longer boot time and reduced resolution of the grub menu that is
displayed on the monitor. This patch avoids that reduced startup
performance when using the Qemu upstream device model for Xen HVM guests
configured with the igd-passthru=on option.
To implement this feature in the Qemu upstream device model for Xen HVM
guests, introduce the following new functions, types, and macros:
* XEN_PT_DEVICE_CLASS declaration, based on the existing TYPE_XEN_PT_DEVICE
* XEN_PT_DEVICE_GET_CLASS macro helper function for XEN_PT_DEVICE_CLASS
* typedef XenPTQdevRealize function pointer
* XEN_PCI_IGD_SLOT_MASK, the value of slot_reserved_mask to reserve slot 2
* xen_igd_reserve_slot and xen_igd_clear_slot functions
Michael Tsirkin:
* Introduce XEN_PCI_IGD_DOMAIN, XEN_PCI_IGD_BUS, XEN_PCI_IGD_DEV, and
XEN_PCI_IGD_FN - use them to compute the value of XEN_PCI_IGD_SLOT_MASK
The new xen_igd_reserve_slot function uses the existing slot_reserved_mask
member of PCIBus to reserve PCI slot 2 for Xen HVM guests configured using
the xl toolstack with the gfx_passthru option enabled, which sets the
igd-passthru=on option to Qemu for the Xen HVM machine type.
The new xen_igd_reserve_slot function also needs to be implemented in
hw/xen/xen_pt_stub.c to prevent FTBFS during the link stage for the case
when Qemu is configured with --enable-xen and --disable-xen-pci-passthrough,
in which case it does nothing.
The new xen_igd_clear_slot function overrides qdev->realize of the parent
PCI device class to enable the Intel IGD to occupy slot 2 on the PCI bus
since slot 2 was reserved by xen_igd_reserve_slot when the PCI bus was
created in hw/i386/pc_piix.c for the case when igd-passthru=on.
Move the call to xen_host_pci_device_get, and the associated error
handling, from xen_pt_realize to the new xen_igd_clear_slot function to
initialize the device class and vendor values which enables the checks for
the Intel IGD to succeed. The verification that the host device is an
Intel IGD to be passed through is done by checking the domain, bus, slot,
and function values as well as by checking that gfx_passthru is enabled,
the device class is VGA, and the device vendor in Intel.
Signed-off-by: Chuck Zmudzinski <brchuckz@aol.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Message-Id: <b1b4a21fe9a600b1322742dda55a40e9961daa57.1674346505.git.brchuckz@aol.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
accel/tcg: Retain prot flags from tlb_fill
accel/tcg: Honor TLB_DISCARD_WRITE in atomic_mmu_lookup
accel/tcg: Honor TLB_WATCHPOINTS in atomic_mmu_lookup
target/sparc: Use tlb_set_page_full
include/qemu/cpuid: Introduce xgetbv_low
tcg/i386: Mark Win64 call-saved vector regs as reserved
tcg: Decode the operand to INDEX_op_mb in dumps
Portion of the target/ patchset which eliminates use of tcg_temp_free*
Portion of the target/ patchset which eliminates use of tcg_const*
-----BEGIN PGP SIGNATURE-----
iQFRBAABCgA7FiEEekgeeIaLTbaoWgXAZN846K9+IV8FAmQFNegdHHJpY2hhcmQu
aGVuZGVyc29uQGxpbmFyby5vcmcACgkQZN846K9+IV9WsQf+Ljs3WA5lvMPlpaSn
Li35ay/A1f2cU6FYspl81su4/c7Ft9Q8rkPF4K1n1rwuvqR91G25WTQIrw8NFPXZ
VU9GNGQc1qIVYO/hAH3fvgDmPxUF+tJDgT/BTNc1ldy6/v7QM3GWcEy8+O3H9S+K
uj6vIuWke0ukq6ZGmSAZnXEaJFq3HU26mcP4KxDxfIUcezMtDVp6QevqzVxM65aa
pUDh3qtsLGOxIYwthvu6avMQXORBhSB75awCuYH4QPJRpr3ahigcGsCr2gdVAQ8p
R7BbpUUdK5Huos971oouJrt5FwwbVgGEx78eF27sl0H8QMoNhsfyn6PcN8nPENLJ
MZYd+w==
=8goQ
-----END PGP SIGNATURE-----
Merge tag 'pull-tcg-20230305' of https://gitlab.com/rth7680/qemu into staging
tcg: Merge two sequential labels
accel/tcg: Retain prot flags from tlb_fill
accel/tcg: Honor TLB_DISCARD_WRITE in atomic_mmu_lookup
accel/tcg: Honor TLB_WATCHPOINTS in atomic_mmu_lookup
target/sparc: Use tlb_set_page_full
include/qemu/cpuid: Introduce xgetbv_low
tcg/i386: Mark Win64 call-saved vector regs as reserved
tcg: Decode the operand to INDEX_op_mb in dumps
Portion of the target/ patchset which eliminates use of tcg_temp_free*
Portion of the target/ patchset which eliminates use of tcg_const*
# -----BEGIN PGP SIGNATURE-----
#
# iQFRBAABCgA7FiEEekgeeIaLTbaoWgXAZN846K9+IV8FAmQFNegdHHJpY2hhcmQu
# aGVuZGVyc29uQGxpbmFyby5vcmcACgkQZN846K9+IV9WsQf+Ljs3WA5lvMPlpaSn
# Li35ay/A1f2cU6FYspl81su4/c7Ft9Q8rkPF4K1n1rwuvqR91G25WTQIrw8NFPXZ
# VU9GNGQc1qIVYO/hAH3fvgDmPxUF+tJDgT/BTNc1ldy6/v7QM3GWcEy8+O3H9S+K
# uj6vIuWke0ukq6ZGmSAZnXEaJFq3HU26mcP4KxDxfIUcezMtDVp6QevqzVxM65aa
# pUDh3qtsLGOxIYwthvu6avMQXORBhSB75awCuYH4QPJRpr3ahigcGsCr2gdVAQ8p
# R7BbpUUdK5Huos971oouJrt5FwwbVgGEx78eF27sl0H8QMoNhsfyn6PcN8nPENLJ
# MZYd+w==
# =8goQ
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 06 Mar 2023 00:38:00 GMT
# gpg: using RSA key 7A481E78868B4DB6A85A05C064DF38E8AF7E215F
# gpg: issuer "richard.henderson@linaro.org"
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [full]
# Primary key fingerprint: 7A48 1E78 868B 4DB6 A85A 05C0 64DF 38E8 AF7E 215F
* tag 'pull-tcg-20230305' of https://gitlab.com/rth7680/qemu: (84 commits)
target/xtensa: Avoid tcg_const_i32
target/xtensa: Split constant in bit shift
target/xtensa: Use tcg_gen_subfi_i32 in translate_sll
target/xtensa: Avoid tcg_const_i32 in translate_l32r
target/xtensa: Tidy translate_clamps
target/xtensa: Tidy translate_bb
target/sparc: Avoid tcg_const_{tl,i32}
target/s390x: Split out gen_ri2
target/riscv: Avoid tcg_const_*
target/microblaze: Avoid tcg_const_* throughout
target/i386: Simplify POPF
target/hexagon/idef-parser: Use gen_constant for gen_extend_tcg_width_op
target/hexagon/idef-parser: Use gen_tmp for gen_rvalue_pred
target/hexagon/idef-parser: Use gen_tmp for gen_pred_assign
target/hexagon/idef-parser: Use gen_tmp for LPCFG
target/hexagon: Use tcg_constant_* for gen_constant_from_imm
docs/devel/tcg-ops: Drop recommendation to free temps
tracing: remove transform.py
include/exec/gen-icount: Drop tcg_temp_free in gen_tb_start
target/tricore: Drop tcg_temp_free
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Simplify the resample buffer size calculation.
For audio playback we have
sw->ratio = ((int64_t)sw->hw->info.freq << 32) / sw->info.freq;
samples = ((int64_t)sw->HWBUF.size << 32) / sw->ratio;
This can be simplified to
samples = muldiv64(sw->HWBUF.size, sw->info.freq, sw->hw->info.freq);
For audio recording we have
sw->ratio = ((int64_t)sw->info.freq << 32) / sw->hw->info.freq;
samples = (int64_t)sw->HWBUF.size * sw->ratio >> 32;
This can be simplified to
samples = muldiv64(sw->HWBUF.size, sw->info.freq, sw->hw->info.freq);
With hw = sw->hw this becomes in both cases
samples = muldiv64(HWBUF.size, sw->info.freq, hw->info.freq);
Now that sw->ratio is no longer needed, remove sw->ratio.
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20230224190555.7409-15-vr_qemu@t-online.de>
Upsampling may leave one remaining audio frame in the input
buffer. The emulated audio playback devices are currently
resposible to write this audio frame again in the next write
cycle. Push that task down to audio_pcm_sw_write.
This is another step towards an audio callback interface that
guarantees that when audio frontends are told they can write
n audio frames, they can actually do so.
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20230224190555.7409-13-vr_qemu@t-online.de>
Introduce the new function st_rate_frames_out() to calculate the
exact number of audio output frames the resampling code can
generate from a given number of audio input frames. When upsampling,
this function returns the maximum number of output frames.
This new function replaces the audio_frontend_frames_in()
function, which calculated the average number of output frames
rounded down to the nearest integer. The audio_frontend_frames_in()
function was additionally used to limit the number of output frames
to the resample buffer size. In audio_pcm_sw_read() the variable
resample_buf.size replaces the open coded audio_frontend_frames_in()
function. In audio_run_in() an additional MIN() function is
necessary.
After this patch the audio packet length calculation for audio
recording is exact.
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20230224190555.7409-12-vr_qemu@t-online.de>
The audio_pcm_sw_read() function uses a few very unspecific
variable names. Rename them for better readability.
ret => total_out
total => total_in
size => buf_len
samples => frames_out_max
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20230224190555.7409-11-vr_qemu@t-online.de>
Replace the resampling loop in audio_pcm_sw_read() with the new
function audio_pcm_sw_resample_in(). Unlike the old resample
loop the new function will try to consume input frames even if
the output buffer is full. This is necessary when downsampling
to avoid reading less audio frames than calculated in advance.
The loop was unrolled to avoid complicated loop control conditions
in this case.
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20230224190555.7409-10-vr_qemu@t-online.de>
Introduce the new function st_rate_frames_in() to calculate the
exact number of audio input frames needed to get a given number
of audio output frames. The exact number of frames depends only
on the difference of opos - ipos and the number of output frames.
When downsampling, this function returns the maximum number of
input frames needed.
This new function replaces the audio_frontend_frames_out() function,
which calculated the average number of input frames rounded down
to the nearest integer. Because audio_frontend_frames_out() also
limited the number of input frames to the size of the resample
buffer, st_rate_frames_in() is not a direct replacement and two
additional MIN() functions are needed. One to prevent resample
buffer overflows and one to limit the available bytes for the audio
frontends.
After this patch the audio packet length calculation for playback is
exact. When upsampling, it's still possible that the audio frontends
can't write the last audio frame. This will be fixed later.
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20230224190555.7409-9-vr_qemu@t-online.de>
The function audio_capture_mix_and_clear() no longer uses
audio_pcm_sw_write() to resample audio frames from one internal
buffer to another. For this reason, the noop_conv() function is
now unused. Remove it.
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20230224190555.7409-8-vr_qemu@t-online.de>
The audio_pcm_sw_write() function is intended to convert a
PCM audio stream to the internal representation, adjust the
volume, and then mix it with the other audio streams with a
possibly changed sample rate in mix_buf. In order for the
audio_capture_mix_and_clear() function to use audio_pcm_sw_write(),
it must bypass the first two tasks of audio_pcm_sw_write().
Since patch "audio: split out the resampling loop in
audio_pcm_sw_write()" this is no longer necessary, because now
the audio_pcm_sw_resample_out() function can be used instead of
audio_pcm_sw_write().
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20230224190555.7409-7-vr_qemu@t-online.de>
The audio_pcm_sw_write() function uses a lot of very unspecific
variable names. Rename them for better readability.
ret => total_in
total => total_out
size => buf_len
hwsamples => hw->mix_buf.size
samples => frames_in_max
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20230224190555.7409-6-vr_qemu@t-online.de>
All call sites of audio_pcm_sw_write() guarantee that sw is not
NULL. Remove the unnecessary NULL check.
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20230224190555.7409-5-vr_qemu@t-online.de>
Replace the resampling loop in audio_pcm_sw_write() with the new
function audio_pcm_sw_resample_out(). Unlike the old resample
loop the new function will try to consume input frames even if
the output buffer is full. This is necessary when downsampling
to avoid reading less audio frames than calculated in advance.
The loop was unrolled to avoid complicated loop control conditions
in this case.
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20230224190555.7409-4-vr_qemu@t-online.de>
Read the maximum possible number of audio frames instead of the
minimum necessary number of frames when the audio stream is
downsampled and the output buffer is limited. This makes the
function symmetrical to upsampling when the input buffer is
limited. The maximum possible number of frames is written here.
With this change it's easier to calculate the exact number of
audio frames the resample function will read or write. These two
functions will be introduced later.
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20230224190555.7409-3-vr_qemu@t-online.de>
Change the type of the resample buffer from struct st_sample *
to STSampleBuffer. Also change the name from buf to resample_buf
for better readability.
The new variables resample_buf.size and resample_buf.pos will be
used after the next patches. There is no functional change.
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20230224190555.7409-2-vr_qemu@t-online.de>
Change the type of mix_buf in struct HWVoiceOut and conv_buf
in struct HWVoiceIn from STSampleBuffer * to STSampleBuffer.
However, a buffer pointer is still needed. For this reason in
struct STSampleBuffer samples[] is changed to *buffer.
This is a preparation for the next patch. The next patch will
add this line, which is not possible with the current struct
STSampleBuffer definition.
+ sw->resample_buf.buffer = hw->mix_buf.buffer + rpos2;
There are no functional changes.
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20230224190555.7409-1-vr_qemu@t-online.de>
Audio recording with ALSA default settings currently doesn't
work. The debug log shows updates every 0.75s and 1.5s.
audio: Elapsed since last alsa run (running): 0.743030
audio: Elapsed since last alsa run (running): 1.486048
audio: Elapsed since last alsa run (running): 0.743008
audio: Elapsed since last alsa run (running): 1.485878
audio: Elapsed since last alsa run (running): 1.486040
audio: Elapsed since last alsa run (running): 1.485886
The time between updates should be in the 10ms range. Audio
recording with ALSA has the same timing contraints as playback.
Reintroduce the default recording settings and use the same
default settings for recording as for playback.
The term "reintroduce" is correct because commit a93f328177
("alsaaudio: port to -audiodev config") removed the default
settings for recording.
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20230121094735.11644-11-vr_qemu@t-online.de>
