For Standard TLB configuration (Config.MT=1):
TLBINV invalidates a set of TLB entries based on ASID. The virtual address is
ignored in the entry match. TLB entries which have their G bit set to 1 are not
modified.
TLBINVF causes all entries to be invalidated.
Single TLB entry can be marked as invalid on TLB entry write by having
EntryHi.EHINV set to 1.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
An Execute-Inhibit exception occurs when the virtual address of an instruction
fetch matches a TLB entry whose XI bit is set. This exception type can only
occur if the XI bit is implemented within the TLB and is enabled, this is
denoted by the PageGrain XIE bit.
An Read-Inhibit exception occurs when the virtual address of a memory load
reference matches a TLB entry whose RI bit is set. This exception type can
only occur if the RI bit is implemented within the TLB and is enabled, this is
denoted by the PageGrain RIE bit.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
PageGrain needs rw bitmask which differs between MIPS architectures.
In pre-R6 if RIXI is supported, PageGrain.XIE and PageGrain.RIE are writeable,
whereas in R6 they are read-only 1.
On MIPS64 mtc0 instruction left shifts bits 31:30 for MIPS32 backward
compatiblity, therefore there are separate mtc0 and dmtc0 helpers.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
In Revision 3 of the architecture, the RI and XI bits were added to the TLB
to enable more secure access of memory pages. These bits (along with the Dirty
bit) allow the implementation of read-only, write-only, no-execute access
policies for mapped pages.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
KScratch<n> Registers (CP0 Register 31, Selects 2 to 7)
The KScratch registers are read/write registers available for scratch pad
storage by kernel mode software. They are 32-bits in width for 32-bit
processors and 64-bits for 64-bit processors.
CP0Config4.KScrExist[2:7] bits indicate presence of CP0_KScratch1-6 registers.
For Release 6, all KScratch registers are required.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
Commit 240ce26a broke MIPS16 and microMIPS support as it didn't
care those branches and jumps don't have delay slot in
MIPS16 and microMIPS.
This patch introduces a new argument delayslot_size to the
gen_compute_branch() indicating size of delay slot {0, 2, 4}.
And the information is used to call handle_delay_slot() forcingly
when no delay slot is required.
There are some microMIPS branch and jump instructions that requires
exact size of instruction in the delay slot. For indicating
these instructions, MIPS_HFLAG_BDS_STRICT flag is introduced.
Those fictional branch opcodes defined to support MIPS16 and
microMIPS are no longer needed.
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Tested-by: Jonas Gorski <jogo@openwrt.org>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
[leon.alrae@imgtec.com: cosmetic changes]
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
In R6 the special behaviour for data references is also specified for Kernel
and Supervisor mode. Therefore MIPS_HFLAG_UX is replaced by generic
MIPS_HFLAG_AWRAP indicating enabled 32-bit address wrapping.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
From MIPS documentation (Volume III):
UserLocal Register (CP0 Register 4, Select 2)
Compliance Level: Recommended.
The UserLocal register is a read-write register that is not interpreted by
the hardware and conditionally readable via the RDHWR instruction.
This register only exists if the Config3-ULRI register field is set.
Privileged software may write this register with arbitrary information and
make it accessible to unprivileged software via register 29 (ULR) of the
RDHWR instruction. To do so, bit 29 of the HWREna register must be set to a
1 to enable unprivileged access to the register.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Prepare for moving softmmu_header.h inclusion out of .c files
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add U suffix to various places where we shift a 1 left by 31,
to avoid undefined behaviour.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Most targets were using offsetof(CPUFooState, breakpoints) to determine
how much of CPUFooState to clear on reset. Use the next field after
CPU_COMMON instead, if any, or sizeof(CPUFooState) otherwise.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Note that while such functions may exist both for *-user and softmmu,
only *-user uses the CPUState hook, while softmmu reuses the prototype
for calling it directly.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Default to false.
Tidy variable naming and inline cast uses while at it.
Tested-by: Jia Liu <proljc@gmail.com> (or32)
Signed-off-by: Andreas Färber <afaerber@suse.de>
Add CP0_Config5, define rw_bitmask and enable modifications.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Reviewed-by: Eric Johnson <eric.johnson@imgtec.com>
Most code already used QEMUTimer without the redundant 'struct' keyword.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Where no extra implementation is needed, fall back to CPUClass::set_pc().
Acked-by: Michael Walle <michael@walle.cc> (for lm32)
Signed-off-by: Andreas Färber <afaerber@suse.de>
The functions cpu_clone_regs() and cpu_set_tls() are not purely CPU
related -- they are specific to the TLS ABI for a a particular OS.
Move them into the linux-user/ tree where they belong.
target-lm32 had entirely unused implementations, since it has no
linux-user target; just drop them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Use it for all targets, but be careful not to pass invalid CPUState.
cpu_single_env can be NULL, e.g. on Xen.
Signed-off-by: Andreas Färber <afaerber@suse.de>
The current ISA mode needs to be saved in bit 0 of the resume address.
If the current instruction happens to be in a branch delay slot, then
the address of the preceding jump instruction should be stored instead.
exception_resume_pc already does both of these tasks, so it is
made available and reused.
MIPS_HFLAG_BMASK in hflags is cleared, otherwise QEMU may treat the
first instruction of the signal handler as a delay slot instruction.
Signed-off-by: Kwok Cheung Yeung <kcy@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This removes a global per-target function and thus takes us one step
closer to compiling multiple targets into one executable.
It will also allow to override the interrupt handling for certain CPU
families.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Both fields are used in VMState, thus need to be moved together.
Explicitly zero them on reset since they were located before
breakpoints.
Pass PowerPCCPU to kvmppc_handle_halt().
Signed-off-by: Andreas Färber <afaerber@suse.de>
Clear the DSP hflags at the start of compute_hflags. Otherwise access
is not properly disabled once enabled.
Signed-off-by: Eric Johnson <ericj@mips.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
For target-mips also change the return type to bool.
Make include paths for cpu-qom.h consistent for alpha and unicore32.
Signed-off-by: Andreas Färber <afaerber@suse.de>
[AF: Updated new target-openrisc function accordingly]
Acked-by: Richard Henderson <rth@twiddle.net> (for alpha)
target_phys_addr_t is unwieldly, violates the C standard (_t suffixes are
reserved) and its purpose doesn't match the name (most target_phys_addr_t
addresses are not target specific). Replace it with a finger-friendly,
standards conformant hwaddr.
Outstanding patchsets can be fixed up with the command
git rebase -i --exec 'find -name "*.[ch]"
| xargs s/target_phys_addr_t/hwaddr/g' origin
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add an explicit CPUState parameter instead of relying on AREG0
and switch to AREG0 free mode.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
This change updates the CPU reset sequence to use a common piece of code
that figures out CPU state flags, fixing the problem with MIPS_HFLAG_COP1X
not being set where applicable that causes floating-point MADD family
instructions (and other instructions from the MIPS IV FP subset) to trap.
As compute_hflags is now shared between op_helper.c and translate.c, the
function is now moved to a common header. There are no changes to this
function.
The problem was seen with the 24Kf MIPS32r2 processor in user emulation.
The new approach prevents system and user emulation from diverging -- all
the hflags state is initialized in one place now.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
In commit 1bba0dc932 cpu_reset()
was renamed to cpu_state_reset(), to allow introducing a new cpu_reset()
that would operate on QOM objects.
All callers have been updated except for one in target-mips, so drop all
implementations except for the one in target-mips and move the
declaration there until MIPSCPU reset can be fully QOM'ified.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Michael Walle <michael@walle.cc> (for lm32)
Acked-by: Max Filippov <jcmvbkbc@gmail.com> (for xtensa)
Acked-by: Edgar E. Iglesias <edgar.iglesias@gmail.com> (for mb + cris)
Acked-by: Alexander Graf <agraf@suse.de> (for ppc)
Acked-by: Blue Swirl <blauwirbel@gmail.com>
* 'qom-cpu-rest.v1' of git://github.com/afaerber/qemu-cpu:
Makefile: Simplify compilation of target-*/cpu.c
target-mips: Start QOM'ifying CPU init
target-mips: QOM'ify CPU
target-m68k: Add QOM CPU subclasses
target-m68k: Start QOM'ifying CPU init
target-m68k: QOM'ify CPU reset
target-m68k: QOM'ify CPU
target-sh4: Start QOM'ifying CPU init
target-sh4: QOM'ify CPU reset
target-sh4: QOM'ify CPU
MAINTAINERS: Downgrade target-mips and target-sh4 to Odd Fixes
MAINTAINERS: Downgrade target-m68k to Odd Fixes
Embed CPUMIPSState as first member of QOM MIPSCPU.
Let CPUClass::reset() call cpu_state_reset() for now.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Richard Henderson <rth@twiddle.net>
osdep.h is included via qemu-common.h.
Prepares for use of [u]int_fast*_t types in softfloat code.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Cc: Ben Taylor <bentaylor.solx86@gmail.com>
Cc: Aurélien Jarno <aurelien@aurel32.net>
Cc: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Bernhard Walle <bernhard@bwalle.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The official spelling is QEMU.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
[blauwirbel@gmail.com: fixed comment style in hw/sun4m.c]
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Scripted conversion:
for file in *.[hc] hw/*.[hc] hw/kvm/*.[hc] linux-user/*.[hc] linux-user/m68k/*.[hc] bsd-user/*.[hc] darwin-user/*.[hc] tcg/*/*.[hc] target-*/cpu.h; do
sed -i "s/CPUState/CPUArchState/g" $file
done
All occurrences of CPUArchState are expected to be replaced by QOM CPUState,
once all targets are QOM'ified and common fields have been extracted.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Scripted conversion:
sed -i "s/CPUState/CPUMIPSState/g" target-mips/*.[hc]
sed -i "s/#define CPUMIPSState/#define CPUState/" target-mips/cpu.h
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Anthony Liguori <aliguori@us.ibm.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Alexander Graf <agraf@suse.de>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Dong Xu Wang <wdongxu@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Parameter is_softmmu (and its evil mutant twin brother is_softmuu)
is not used in cpu_*_handle_mmu_fault() functions, remove them
and adjust callers.
Acked-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Move softmmu_exec.h include directives from target-*/exec.h to
target-*/op_helper.c. Move also various other stuff only used in
op_helper.c there.
Define global env in dyngen-exec.h.
For i386, move wrappers for segment and FPU helpers from user-exec.c
to op_helper.c. Implement raise_exception_err_env() to handle dynamic
CPUState. Move the function declarations to cpu.h since they can be
used outside of op_helper.c context.
LM32, s390x, UniCore32: remove unused cpu_halted(), regs_to_env() and
env_to_regs().
ARM: make raise_exception() static.
Convert
#include "exec.h"
to
#include "cpu.h"
#include "dyngen-exec.h"
and remove now unused target-*/exec.h.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
cea5f9a28f exposed bugs in unassigned memory
access handling. Fix them by always passing CPUState to the handlers.
Reported-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Move functions cpu_has_work() and cpu_pc_from_tb() from exec.h to cpu.h. This is
needed by later patches.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
