According to the ast2600 datasheet and the linux aspeed i2c driver,
the TXBUF transmission start position should be TXBUF[0] instead
of TXBUF[1],so the arg pool_start is useless,and the address is not
included in TXBUF.So even if Tx Count equals zero,there is at least
1 byte data needs to be transmitted,and M_TX_CMD should not be cleared
at this condition.The driver url is:
https://github.com/AspeedTech-BMC/linux/blob/aspeed-master-v5.15/drivers/i2c/busses/i2c-ast2600.c
Signed-off-by: Hang Yu <francis_yuu@stu.pku.edu.cn>
Fixes: 6054fc73e8 ("aspeed/i2c: Add support for pool buffer transfers")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
(cherry picked from commit 961faf3ddb)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Fixed inconsistency between the regisiter bit field definition header file
and the ast2600 datasheet. The reg name is I2CD1C:Pool Buffer Control
Register in old register mode and I2CC0C: Master/Slave Pool Buffer Control
Register in new register mode. They share bit field
[12:8]:Transmit Data Byte Count and bit field
[29:24]:Actual Received Pool Buffer Size according to the datasheet.
According to the ast2600 datasheet,the actual Tx count is
Transmit Data Byte Count plus 1, and the max Rx size is
Receive Pool Buffer Size plus 1, both in Pool Buffer Control Register.
The version before forgot to plus 1, and mistake Rx count for Rx size.
Signed-off-by: Hang Yu <francis_yuu@stu.pku.edu.cn>
Fixes: 3be3d6ccf2 ("aspeed: i2c: Migrate to registerfields API")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
(cherry picked from commit 97b8aa5ae9)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The clock and data values were logged swapped. Correct the trace event
text to match what is logged. Also fix a typo in a comment nearby.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
We use the user_ss[] array to hold the user emulation sources,
and the softmmu_ss[] array to hold the system emulation ones.
Hold the latter in the 'system_ss[]' array for parity with user
emulation.
Mechanical change doing:
$ sed -i -e s/softmmu_ss/system_ss/g $(git grep -l softmmu_ss)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230613133347.82210-10-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This allows the devices to be more readily found and specified.
Without setting the name field, they can only be found by device type
name, which doesn't let you specify the second of the same device type
behind a bus.
Tested: Verified that by default the device was findable with the name
'pca954x[77]', for an instance attached at that address.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <20230322172136.48010-1-venture@google.com>
[PMD: Fix typo in property name]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
In commit 8461bfdca9 we added the TYPE_AW_I2C_SUN6I, which is a
minor variant of the TYPE_AW_I2C device. However, we didn't quite
get the class hierarchy right. We made the new TYPE_AW_I2C_SUN6I a
subclass of TYPE_SYS_BUS_DEVICE, which means that you can't validly
use a pointer to this object via the AW_I2C() cast macro, which
insists on having something that is an instance of TYPE_AW_I2C or
some subclass of that type.
This only causes a problem if QOM cast macro debugging is enabled;
that is supposed to be on by default, but a mistake in the meson
conversion in commit c55cf6ab03 meant that it ended up disabled by
default, and we didn't catch this bug.
Fix the problem by arranging the classes in the same way we do for
TYPE_PL011 and TYPE_PL011_LUMINARY in hw/char/pl011.c -- make the
variant class be a subclass of the "normal" version of the device.
This was reported in
https://gitlab.com/qemu-project/qemu/-/issues/1586 but this fix alone
isn't sufficient, as there is a separate cast-related issue in the
CXL code in pci_expander_bridge.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Devices models calling pmbus_send_string can't be relied upon to
send a non-zero pointer. This logs an error and doesn't segfault.
Reviewed-by: Patrick Venture <venture@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230322175513.1550412-5-titusr@google.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
It is not given that the current master will release the bus after a
transfer ends. Only schedule a pending master if the bus is idle.
Fixes: 37fa5ca426 ("hw/i2c: support multiple masters")
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <20221116084312.35808-2-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
ICH9 is a south bridge which doesn't necessarily depend on x86, so move
it into the southbridge folder, analoguous to PIIX.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230213173033.98762-13-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
ich9_smb_init() is a legacy init function, so modernize the code.
Note that the smb_io_base parameter was unused.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230213173033.98762-6-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This is a preparation for the next commit to make it cleaner.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230213173033.98762-5-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This commit was created with scripts/clean-includes.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20230202133830.2152150-19-armbru@redhat.com>
Frees isa-bus.c from implicit ACPI dependency.
While at it, resolve open coding of qbus_build_aml() in piix3 and ich9.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230121151941.24120-3-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
ARM_SBCON_I2C() macro and ArmSbconI2CState typedef are
already declared via the QOM DECLARE_INSTANCE_CHECKER()
macro in "hw/i2c/arm_sbcon_i2c.h". Drop the VERSATILE_I2C
declarations from versatile_i2c.c.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230110082508.24038-5-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230110082508.24038-4-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In order to rename TYPE_VERSATILE_I2C as TYPE_ARM_SBCON_I2C
(the formal ARM naming), start renaming its state.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230110082508.24038-3-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230110082508.24038-2-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Define TYPE_GPIO_I2C in the public "hw/i2c/bitbang_i2c.h"
header and use it in hw/arm/musicpal.c.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20230111085016.44551-2-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 'hwaddr' type is defined in "exec/hwaddr.h" as:
hwaddr is the type of a physical address
(its size can be different from 'target_ulong').
All definitions use the 'HWADDR_' prefix, except TARGET_FMT_plx:
$ fgrep define include/exec/hwaddr.h
#define HWADDR_H
#define HWADDR_BITS 64
#define HWADDR_MAX UINT64_MAX
#define TARGET_FMT_plx "%016" PRIx64
^^^^^^
#define HWADDR_PRId PRId64
#define HWADDR_PRIi PRIi64
#define HWADDR_PRIo PRIo64
#define HWADDR_PRIu PRIu64
#define HWADDR_PRIx PRIx64
#define HWADDR_PRIX PRIX64
Since hwaddr's size can be *different* from target_ulong, it is
very confusing to read one of its format using the 'TARGET_FMT_'
prefix, normally used for the target_long / target_ulong types:
$ fgrep TARGET_FMT_ include/exec/cpu-defs.h
#define TARGET_FMT_lx "%08x"
#define TARGET_FMT_ld "%d"
#define TARGET_FMT_lu "%u"
#define TARGET_FMT_lx "%016" PRIx64
#define TARGET_FMT_ld "%" PRId64
#define TARGET_FMT_lu "%" PRIu64
Apparently this format was missed during commit a8170e5e97
("Rename target_phys_addr_t to hwaddr"), so complete it by
doing a bulk-rename with:
$ sed -i -e s/TARGET_FMT_plx/HWADDR_FMT_plx/g $(git grep -l TARGET_FMT_plx)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230110212947.34557-1-philmd@linaro.org>
[thuth: Fix some warnings from checkpatch.pl along the way]
Signed-off-by: Thomas Huth <thuth@redhat.com>
This patch implements Allwinner TWI/I2C controller emulation. Only
master-mode functionality is implemented.
The SPL boot for Cubieboard expects AXP209 PMIC on TWI0/I2C0 bus, so this is
first part enabling the TWI/I2C bus operation.
Since both Allwinner A10 and H3 use the same module, it is added for
both boards.
Docs are also updated for Cubieboard and Orangepi-PC board to indicate
I2C availability.
Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20221226220303.14420-4-strahinja.p.jankovic@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Although the ICH9 ACPI controller may currently be tied to x86 it
doesn't have to. Furthermore, the source files this configuration switch
manages contain a '9', so this name fits more.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221216130355.41667-2-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
I think when Klaus ported his slave mode changes from the original patch
series to the rewritten I2C module, he changed the behavior of the first
byte that is received by the slave device.
What's supposed to happen is that the AspeedI2CBus's slave device's
i2c_event callback should run, and if the event is "send_async", then it
should populate the byte buffer with the 8-bit I2C address that is being
sent to. Since we only support "send_async", the lowest bit should
always be 0 (indicating that the master is requesting to send data).
This is the code Klaus had previously, for reference. [1]
switch (event) {
case I2C_START_SEND:
bus->buf = bus->dev_addr << 1;
bus->buf &= I2CD_BYTE_BUF_RX_MASK;
bus->buf <<= I2CD_BYTE_BUF_RX_SHIFT;
bus->intr_status |= (I2CD_INTR_SLAVE_ADDR_RX_MATCH | I2CD_INTR_RX_DONE);
aspeed_i2c_set_state(bus, I2CD_STXD);
break;
[1]: https://lore.kernel.org/qemu-devel/20220331165737.1073520-4-its@irrelevant.dk/
Fixes: a8d48f59cd ("hw/i2c/aspeed: add slave device in old register mode")
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20220820225712.713209-2-peter@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Titus Rwantare <titusr@google.com>
Message-Id: <20220701000626.77395-2-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This commit adds support for DMA RX in slave mode while using the new
register set in the AST2600 and AST1030. This patch also pretty much
assumes packet mode is enabled, I'm not sure if this will work in DMA
step mode.
This is particularly useful for testing IPMB exchanges between Zephyr
and external devices, which requires multi-master I2C support and DMA in
the new register mode, because the Zephyr drivers from Aspeed use DMA in
the new mode by default. The Zephyr drivers are also using packet mode.
The typical sequence of events for receiving data in DMA slave + packet
mode is that the Zephyr firmware will configure the slave address
register with an address to receive on and configure the bus's function
control register to enable master mode and slave mode simultaneously at
startup, before any transfers are initiated.
RX DMA is enabled in the slave mode command register, and the slave RX
DMA buffer address and slave RX DMA buffer length are set. TX DMA is not
covered in this patch.
When the Aspeed I2C controller receives data from some other I2C master,
it will reset the I2CS_DMA_LEN RX_LEN value to zero, then buffer
incoming data in the RX DMA buffer while incrementing the I2CC_DMA_ADDR
address counter and decrementing the I2CC_DMA_LEN counter. It will also
update the I2CS_DMA_LEN RX_LEN value along the way.
Once all the data has been received, the bus controller will raise an
interrupt indicating a packet command was completed, the slave address
matched, a normal stop condition was seen, and the transfer was an RX
operation.
If the master sent a NACK instead of a normal stop condition, or the
transfer timed out, then a slightly different set of interrupt status
values would be set. Those conditions are not handled in this commit.
The Zephyr firmware then collects data from the RX DMA buffer and clears
the status register by writing the PKT_MODE_EN bit to the status
register. In packet mode, clearing the packet mode interrupt enable bit
also clears most of the other interrupt bits automatically (except for a
few bits above it).
Note: if the master transmit or receive functions were in use
simultaneously with the slave mode receive functionality, then the
master mode functions may have raised the interrupt line for the bus
before the DMA slave transfer is complete. It's important to have the
slave's interrupt status register clear throughout the receive
operation, and if the slave attempts to raise the interrupt before the
master interrupt status is cleared, then it needs to re-raise the
interrupt once the master interrupt status is cleared. (And vice-versa).
That's why in this commit, when the master interrupt status is cleared
and the interrupt line is lowered, we call the slave interrupt _raise_
function, to see if the interrupt was pending. (And again, vice-versa).
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220630045133.32251-8-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add slave mode functionality for the Aspeed I2C controller in old
register mode. This is implemented by realizing an I2C slave device
owned by the I2C controller and attached to its own bus.
The I2C slave device only implements asynchronous sends on the bus, so
slaves not supporting that will not be able to communicate with it.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg: checkpatch fixes ]
Message-Id: <20220601210831.67259-6-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-7-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add an asynchronous version of i2c_send() that requires the slave to
explicitly acknowledge on the bus with i2c_ack().
The current master must use the new i2c_start_send_async() to indicate
that it wants to do an asynchronous transfer. This allows the i2c core
to check if the target slave supports this or not. This approach relies
on adding a new enum i2c_event member, which is why a bunch of other
devices needs changes in their event handling switches.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20220601210831.67259-5-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-6-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Allow slaves to master the bus by registering a bottom halve. If the bus
is busy, the bottom half is queued up. When a slave has succesfully
mastered the bus, the bottom half is scheduled.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg : - fixed typos in commit log ]
Message-Id: <20220601210831.67259-4-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-5-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
aspeed_i2c_bus_is_master is checking if master mode is enabled in the I2C
bus controller's function-control register, not that slave mode is enabled
or something. The error here is that the guest is trying to trigger an I2C
master mode command while master mode is not enabled.
Fixes: ba2cccd64e ("aspeed: i2c: Add new mode support")
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220630045133.32251-4-me@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
I noticed i2c rx transfers were getting shortened to "1" on Zephyr. It
seems to be because the Zephyr i2c driver sets the RX DMA len with the
RX field write-enable bit set (bit 31) to avoid a read-modify-write. [1]
/* 0x1C : I2CM Master DMA Transfer Length Register */
I think we should be checking the write-enable bits on the incoming
value, not checking the register array. I'm not sure we're even writing
the write-enable bits to the register array, actually.
[1] db3dbcc9c5/drivers/i2c/i2c_aspeed.c (L145-L148)
Fixes: ba2cccd64e ("aspeed: i2c: Add new mode support")
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220630045133.32251-3-me@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Very minor, doesn't effect functionality, but this is supposed to be
R_I2CC_FUN_CTRL (new-mode, not old-mode).
Fixes: ba2cccd64e ("aspeed: i2c: Add new mode support")
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220630045133.32251-2-me@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Current implementation of the pmbus core driver treats the read request
for page 255 as invalid request and sets the invalid command bit (bit 7)
in the STATUS_CML register. As per the PMBus specification it is a valid
request.
Refer to the PMBus specification, revision 1.3.1, section 11.10 PAGE,
on the page 58:
"Setting the PAGE to FFh means that all subsequent comands are to be
applied to all outputs.
Some commands, such as READ_TEMPERATURE, may use a common sensor but
be available on all pages of a device. Such implementations are the
decision of each device manufacturer or are specified in a PMBus
Application Profile. Consult the manufacturer's documents or the
Application Profile Specification as needed."
For e.g.,
The VOUT_MODE is a valid command for page 255 for maxim 31785 device.
refer to Table 1. PMBus Command Codes on page 14 in the datasheet.
https://datasheets.maximintegrated.com/en/ds/MAX31785.pdf
Fixes: 38870253f1 ("hw/i2c: pmbus: fix error returns and guard against out of range accesses")
Signed-off-by: Maheswara Kurapati <quic_mkurapat@quicinc.com>
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220627154703.148943-4-quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Using a 'stop' string seems more appropriate than 'normal'.
Reviewed-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220628154740.1117349-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There is no 'slave match interrupt' enable bit in the Interrupt
Control Register. Consider it is always enabled and extend the mask
value 'bus->regs[intr_ctrl_reg]' with the SLAVE_ADDR_RX_MATCH bit when
the interrupt is raised.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add support for writing and reading the device address register in old
register mode.
On the AST2400 (only 1 slave address)
* no upper bits
On the AST2500 (2 possible slave addresses),
* bit[31] : Slave Address match indicator
* bit[30] : Slave Address Receiving pending
On the AST2600 (3 possible slave addresses),
* bit[31-30] : Slave Address match indicator
* bit[29] : Slave Address Receiving pending
The model could be more precise to take into account all fields but
since the Linux driver is masking the register value being set, it
should be fine. See commit 3fb2e2aeafb2 ("i2c: aspeed: disable
additional device addresses on ast2[56]xx") from Zeiv. This can be
addressed later.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg: add details to commit log ]
Message-Id: <20220601210831.67259-3-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Build a single string instead of having several parameters on the trace
event.
Suggested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg: simplified trace buffer creation ]
Message-Id: <20220601210831.67259-2-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Moves register definitions and short commonly used inlined functiosn to
the header file to help tidy up the implementation file.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I34dff7485b6bbe3c9482715ccd94dbd65dc5f324
Message-Id: <20220331043248.2237838-8-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
On AST2600, I2C has a secondary mode, called "new mode", which changes
the layout of registers, adds some minor behavior changes, and
introduces a new way to transfer data called "packet mode".
Most of the bit positions of the fields are the same between old and new
mode, so we use SHARED_FIELD_XX macros to reuse most of the code between
the different modes.
For packet mode, most of the command behavior is the same compared to
other modes, but there are some minor changes to how interrupts are
handled compared to other modes.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I072f8301964f623afc74af1fe50c12e5caef199e
Message-Id: <20220331043248.2237838-6-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Using a register array will allow us to represent old-mode and new-mode
I2C registers by using the same underlying register array, instead of
adding an entire new set of variables to represent new mode.
As part of this, we also do additional cleanup to use ARRAY_FIELD_
macros instead of FIELD_ macros on registers.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: Ib94996b17c361b8490c042b43c99d8abc69332e3
[ clg: use of memset in aspeed_i2c_bus_reset() ]
Message-Id: <20220331043248.2237838-5-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This cleans up some of the field accessing, setting, and clearing
bitwise operations, and wraps them in macros instead.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I33018d6325fa04376e7c29dc4a49ab389a8e333a
Message-Id: <20220331043248.2237838-4-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
wire AcpiDevAmlIf interface to build ich9-smb and its slave
devices AML. It will be used by followup patches to switch
from creating AML in ad-hoc way to a more systematic one
that will scan present devices and ask them to provide
their AML code like it's done with ISA devices.
This patch is a partial conversion, as it only fetches
AML from slave devices attached to its I2C bus.
The conversion will be completed when PCI bus is
switched to use AcpiDevAmlIf and build_smb0() could be
dropped.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220608135340.3304695-16-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
g_new(T, n) is neater than g_malloc(sizeof(T) * n). It's also safer,
for two reasons. One, it catches multiplication overflowing size_t.
Two, it returns T * rather than void *, which lets the compiler catch
more type errors.
This commit only touches allocations with size arguments of the form
sizeof(T).
Patch created mechanically with:
$ spatch --in-place --sp-file scripts/coccinelle/use-g_new-etc.cocci \
--macro-file scripts/cocci-macro-file.h FILES...
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20220315144156.1595462-4-armbru@redhat.com>
Reviewed-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
