Commit Graph

138 Commits

Author SHA1 Message Date
Guenter Roeck
7faf6f1790 aspeed/smc: Fix number of dummy cycles for FAST_READ_4 command
The Linux kernel recently started using FAST_READ_4 commands.
This results in flash read failures. At the same time, the m25p80
emulation is seen to read 8 more bytes than expected. Adjusting the
expected number of dummy cycles to match FAST_READ fixes the problem.

Fixes: f95c4bffdc ("aspeed/smc: snoop SPI transfers to fake dummy cycles")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2020-03-17 11:36:44 +00:00
Cédric Le Goater
e7e741ca9d aspeed/smc: Fix User mode select/unselect scheme
The Aspeed SMC Controller can operate in different modes : Read, Fast
Read, Write and User modes. When the User mode is configured, it
selects automatically the SPI slave device until the CE_STOP_ACTIVE
bit is set to 1. When any other modes are configured the device is
unselected. The HW logic handles the chip select automatically when
the flash is accessed through its AHB window.

When configuring the CEx Control Register, the User mode logic to
select and unselect the slave is incorrect and data corruption can be
seen on machines using two chips, witherspoon and romulus.

Rework the handler setting the CEx Control Register to fix this issue.

Fixes: 7c1c69bca4 ("ast2400: add SMC controllers (FMC and SPI)")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20200206112645.21275-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2020-03-12 16:01:37 +00:00
Cédric Le Goater
bd6ce9a6ed aspeed/smc: Add some tracing
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200206112645.21275-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2020-03-12 16:01:37 +00:00
Francisco Iglesias
33e2c4d8d3 xilinx_spips: Correct the number of dummy cycles for the FAST_READ_4 cmd
Correct the number of dummy cycles required by the FAST_READ_4 command (to
be eight, one dummy byte).

Fixes: ef06ca3946 ("xilinx_spips: Add support for RX discard and RX drain")
Suggested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20200218113350.6090-1-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2020-02-21 16:07:02 +00:00
Thomas Huth
3ab5a6ece5 hw/*/Makefile.objs: Move many .o files to common-objs
We have many files that apparently do not depend on the target CPU
configuration, i.e. which can be put into common-obj-y instead of
obj-y. This way, the code can be shared for example between
qemu-system-arm and qemu-system-aarch64, or the various big and
little endian variants like qemu-system-sh4 and qemu-system-sh4eb,
so that we do not have to compile the code multiple times anymore.

Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200130133841.10779-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
2020-02-04 09:00:57 +01:00
Marc-André Lureau
4f67d30b5e qdev: set properties with device_class_set_props()
The following patch will need to handle properties registration during
class_init time. Let's use a device_class_set_props() setter.

spatch --macro-file scripts/cocci-macro-file.h  --sp-file
./scripts/coccinelle/qdev-set-props.cocci --keep-comments --in-place
--dir .

@@
typedef DeviceClass;
DeviceClass *d;
expression val;
@@
- d->props = val
+ device_class_set_props(d, val)

Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20200110153039.1379601-20-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2020-01-24 20:59:15 +01:00
Cédric Le Goater
f286f04c21 aspeed/smc: Add AST2600 timings registers
Each CS has its own Read Timing Compensation Register on newer SoCs.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-13-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-12-16 10:46:34 +00:00
Cédric Le Goater
2175eacfcd aspeed/smc: Do not map disabled segment on the AST2600
The segments can be disabled on the AST2600 (zero register value).
CS0 is open by default but not the other CS. This is closing the
access to the flash device in user mode and forbids scanning.

In the model, check the segment size and disable the associated region
when the value is zero.

Fixes: bcaa8ddd08 ("aspeed/smc: Add AST2600 support")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-12-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-12-16 10:46:34 +00:00
Cédric Le Goater
673b1f8650 aspeed/smc: Restore default AHB window mapping at reset
The current model only restores the Segment Register values but leaves
the previous CS mapping behind. Introduce a helper setting the
register value and mapping the region at the requested address. Use
this helper when a Segment register is set and at reset.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-11-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-12-16 10:46:34 +00:00
Sai Pavan Boddu
3a6606c7aa ssi: xilinx_spips: Skip spi bus update for a few register writes
A few configuration register writes need not update the spi bus state, so just
return after the register write.

Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Tested-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1573830705-14579-1-git-send-email-sai.pavan.boddu@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-11-19 13:20:27 +00:00
Cédric Le Goater
bcaa8ddd08 aspeed/smc: Add AST2600 support
The AST2600 SoC SMC controller is a SPI only controller now and has a
few extensions which we will need to take into account when SW
requires it. This is enough to support u-boot and Linux.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-14-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-10-15 18:09:04 +01:00
Cédric Le Goater
d0e2504008 aspeed/smc: Introduce segment operations
AST2600 will use a different encoding for the addresses defined in the
Segment Register.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-13-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-10-15 18:09:04 +01:00
Christian Svensson
ae275f7133 aspeed/smc: Calculate checksum on normal DMA
This patch adds the missing checksum calculation on normal DMA transfer.
According to the datasheet this is how the SMC should behave.

Verified on AST1250 that the hardware matches the behaviour.

Signed-off-by: Christian Svensson <bluecmd@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-9-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-09-13 16:05:01 +01:00
Cédric Le Goater
5258c2a69c aspeed/smc: Inject errors in DMA checksum
Emulate read errors in the DMA Checksum Register for high frequencies
and optimistic settings of the Read Timing Compensation Register. This
will help in tuning the SPI timing calibration algorithm. Errors are
only injected when the property "inject_failure" is set to true as
suggested by Philippe.

The values below are those to expect from the first flash device of
the FMC controller of a palmetto-bmc machine.

Cc: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190904070506.1052-8-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-09-13 16:05:01 +01:00
Cédric Le Goater
0d72c71702 aspeed/smc: Add DMA calibration settings
When doing calibration, the SPI clock rate in the CE0 Control Register
and the read delay cycles in the Read Timing Compensation Register are
set using bit[11:4] of the DMA Control Register.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190904070506.1052-7-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-09-13 16:05:01 +01:00
Cédric Le Goater
c4e1f0b483 aspeed/smc: Add support for DMAs
The FMC controller on the Aspeed SoCs support DMA to access the flash
modules. It can operate in a normal mode, to copy to or from the flash
module mapping window, or in a checksum calculation mode, to evaluate
the best clock settings for reads.

The model introduces two custom address spaces for DMAs: one for the
AHB window of the FMC flash devices and one for the DRAM. The latter
is populated using a "dram" link set from the machine with the RAM
container region.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190904070506.1052-6-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-09-13 16:05:01 +01:00
Cédric Le Goater
811a5b1d6c aspeed: Use consistent typenames
Improve the naming of the different controller models to ease their
generation when initializing the SoC. The rename of the SMC types is
breaking migration compatibility.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-5-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-09-13 16:05:01 +01:00
Markus Armbruster
d5938f29fe Clean up inclusion of sysemu/sysemu.h
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).

Almost a third of its inclusions are actually superfluous.  Delete
them.  Downgrade two more to qapi/qapi-types-run-state.h, and move one
from char/serial.h to char/serial.c.

hw/semihosting/config.c, monitor/monitor.c, qdev-monitor.c, and
stubs/semihost.c define variables declared in sysemu/sysemu.h without
including it.  The compiler is cool with that, but include it anyway.

This doesn't reduce actual use much, as it's still included into
widely included headers.  The next commit will tackle that.

Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-27-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
2019-08-16 13:31:53 +02:00
Markus Armbruster
a27bd6c779 Include hw/qdev-properties.h less
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).

Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h.  Include hw/qdev-core.h there
instead.

hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.

While there, delete a few superfluous inclusions of hw/qdev-core.h.

Touching hw/qdev-properties.h now recompiles some 1200 objects.

Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
2019-08-16 13:31:53 +02:00
Markus Armbruster
d645427057 Include migration/vmstate.h less
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).

hw/hw.h supposedly includes it for convenience.  Several other headers
include it just to get VMStateDescription.  The previous commit made
that unnecessary.

Include migration/vmstate.h only where it's still needed.  Touching it
now recompiles only some 1600 objects.

Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
2019-08-16 13:31:52 +02:00
Markus Armbruster
64552b6be4 Include hw/irq.h a lot less
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).

hw/hw.h supposedly includes it for convenience.  Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.

Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed.  Touching it now recompiles only some 500 objects.

Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
2019-08-16 13:31:52 +02:00
Philippe Mathieu-Daudé
c0bccee9b4 hw/ssi/mss-spi: Avoid crash when reading empty RX FIFO
Reading the RX_DATA register when the RX_FIFO is empty triggers
an abort. This can be easily reproduced:

  $ qemu-system-arm -M emcraft-sf2 -monitor stdio -S
  QEMU 4.0.50 monitor - type 'help' for more information
  (qemu) x 0x40001010
  Aborted (core dumped)

  (gdb) bt
  #1  0x00007f035874f895 in abort () at /lib64/libc.so.6
  #2  0x00005628686591ff in fifo8_pop (fifo=0x56286a9a4c68) at util/fifo8.c:66
  #3  0x00005628683e0b8e in fifo32_pop (fifo=0x56286a9a4c68) at include/qemu/fifo32.h:137
  #4  0x00005628683e0efb in spi_read (opaque=0x56286a9a4850, addr=4, size=4) at hw/ssi/mss-spi.c:168
  #5  0x0000562867f96801 in memory_region_read_accessor (mr=0x56286a9a4b60, addr=16, value=0x7ffeecb0c5c8, size=4, shift=0, mask=4294967295, attrs=...) at memory.c:439
  #6  0x0000562867f96cdb in access_with_adjusted_size (addr=16, value=0x7ffeecb0c5c8, size=4, access_size_min=1, access_size_max=4, access_fn=0x562867f967c3 <memory_region_read_accessor>, mr=0x56286a9a4b60, attrs=...) at memory.c:569
  #7  0x0000562867f99940 in memory_region_dispatch_read1 (mr=0x56286a9a4b60, addr=16, pval=0x7ffeecb0c5c8, size=4, attrs=...) at memory.c:1420
  #8  0x0000562867f99a08 in memory_region_dispatch_read (mr=0x56286a9a4b60, addr=16, pval=0x7ffeecb0c5c8, size=4, attrs=...) at memory.c:1447
  #9  0x0000562867f38721 in flatview_read_continue (fv=0x56286aec6360, addr=1073745936, attrs=..., buf=0x7ffeecb0c7c0 "\340ǰ\354\376\177", len=4, addr1=16, l=4, mr=0x56286a9a4b60) at exec.c:3385
  #10 0x0000562867f38874 in flatview_read (fv=0x56286aec6360, addr=1073745936, attrs=..., buf=0x7ffeecb0c7c0 "\340ǰ\354\376\177", len=4) at exec.c:3423
  #11 0x0000562867f388ea in address_space_read_full (as=0x56286aa3e890, addr=1073745936, attrs=..., buf=0x7ffeecb0c7c0 "\340ǰ\354\376\177", len=4) at exec.c:3436
  #12 0x0000562867f389c5 in address_space_rw (as=0x56286aa3e890, addr=1073745936, attrs=..., buf=0x7ffeecb0c7c0 "\340ǰ\354\376\177", len=4, is_write=false) at exec.c:3466
  #13 0x0000562867f3bdd7 in cpu_memory_rw_debug (cpu=0x56286aa19d00, addr=1073745936, buf=0x7ffeecb0c7c0 "\340ǰ\354\376\177", len=4, is_write=0) at exec.c:3976
  #14 0x000056286811ed51 in memory_dump (mon=0x56286a8c32d0, count=1, format=120, wsize=4, addr=1073745936, is_physical=0) at monitor/misc.c:730
  #15 0x000056286811eff1 in hmp_memory_dump (mon=0x56286a8c32d0, qdict=0x56286b15c400) at monitor/misc.c:785
  #16 0x00005628684740ee in handle_hmp_command (mon=0x56286a8c32d0, cmdline=0x56286a8caeb2 "0x40001010") at monitor/hmp.c:1082

From the datasheet "Actel SmartFusion Microcontroller Subsystem
User's Guide" Rev.1, Table 13-3 "SPI Register Summary", this
register has a reset value of 0.

Check the FIFO is not empty before accessing it, else log an
error message.

Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20190709113715.7761-3-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-07-15 14:17:03 +01:00
Philippe Mathieu-Daudé
526668c734 hw/ssi/xilinx_spips: Avoid out-of-bound access to lqspi_buf[]
Both lqspi_read() and lqspi_load_cache() expect a 32-bit
aligned address.

>From UG1085 datasheet [*] chapter on 'Quad-SPI Controller':

  Transfer Size Limitations

    Because of the 32-bit wide TX, RX, and generic FIFO, all
    APB/AXI transfers must be an integer multiple of 4-bytes.
    Shorter transfers are not possible.

Set MemoryRegionOps.impl values to force 32-bit accesses,
this way we are sure we do not access the lqspi_buf[] array
out of bound.

[*] https://www.xilinx.com/support/documentation/user_guides/ug1085-zynq-ultrascale-trm.pdf

Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Tested-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-07-15 14:17:03 +01:00
Philippe Mathieu-Daudé
936a236c4e hw/ssi/xilinx_spips: Avoid AXI writes to the LQSPI linear memory
Lei Sun found while auditing the code that a CPU write would
trigger a NULL pointer dereference.

>From UG1085 datasheet [*] AXI writes in this region are ignored
and generates an AXI Slave Error (SLVERR).

Fix by implementing the write_with_attrs() handler.
Return MEMTX_ERROR when the region is accessed (this error maps
to an AXI slave error).

[*] https://www.xilinx.com/support/documentation/user_guides/ug1085-zynq-ultrascale-trm.pdf

Reported-by: Lei Sun <slei.casper@gmail.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Tested-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-07-15 14:17:03 +01:00
Philippe Mathieu-Daudé
5937bd50d3 hw/ssi/xilinx_spips: Convert lqspi_read() to read_with_attrs
In the next commit we will implement the write_with_attrs()
handler. To avoid using different APIs, convert the read()
handler first.

Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Tested-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-07-15 14:17:03 +01:00
Cédric Le Goater
6da4433fc5 aspeed/smc: add a 'sdram_base' property
The DRAM address of a DMA transaction depends on the DRAM base address
of the SoC. Inform the SMC controller model with this value.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190618165311.27066-15-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-07-01 17:28:59 +01:00
Markus Armbruster
0b8fa32f55 Include qemu/module.h where needed, drop it from qemu-common.h
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-4-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
hw/usb/dev-hub.c hw/misc/exynos4210_rng.c hw/misc/bcm2835_rng.c
hw/misc/aspeed_scu.c hw/display/virtio-vga.c hw/arm/stm32f205_soc.c;
ui/cocoa.m fixed up]
2019-06-12 13:18:33 +02:00
Peter Maydell
aa64cfaeb4 hw/ssi/xilinx_spips: Avoid variable length array
In the stripe8() function we use a variable length array; however
we know that the maximum length required is MAX_NUM_BUSSES. Use
a fixed-length array and an assert instead.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20190328152635.2794-1-peter.maydell@linaro.org
2019-04-29 17:35:57 +01:00
Paolo Bonzini
1001800cc6 ssi: express dependencies with kconfig
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2019-03-07 21:45:53 +01:00
Paolo Bonzini
82f5181777 kconfig: introduce kconfig files
The Kconfig files were generated mostly with this script:

  for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
    set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
    shift
    if test $# = 1; then
      cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
    bool

EOF
      git add $(dirname $1)/Kconfig
    else
      echo $i $*
    fi
  done
  sed -i '$d' hw/*/Kconfig
  for i in hw/*; do
    if test -d $i && ! test -f $i/Kconfig; then
      touch $i/Kconfig
      git add $i/Kconfig
    fi
  done

Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.

Kconfig.host and hw/Kconfig were created manually.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2019-03-07 21:45:53 +01:00
Cédric Le Goater
f95c4bffdc aspeed/smc: snoop SPI transfers to fake dummy cycles
The m25p80 models dummy cycles using byte transfers. This works well
when the transfers are initiated by the QEMU model of a SPI controller
but when these are initiated by the OS, it breaks emulation.

Snoop the SPI transfer to catch commands requiring dummy cycles and
replace them with byte transfers compatible with the m25p80 model.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 20190124140519.13838-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-01-29 11:46:05 +00:00
Cédric Le Goater
9149af2a2d aspeed/smc: Add dummy data register
The SMC controllers have a register containing the byte that will be
used as dummy output. It can be modified by software.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190124140519.13838-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-01-29 11:46:05 +00:00
Cédric Le Goater
597d6bb3e8 aspeed/smc: define registers for all possible CS
The model should expose one control register per possible CS. When
testing the validity of the register number in the read operation,
replace 's->num_cs' by 'ctrl->max_slaves' which represents the maximum
number of flash devices a controller can handle.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190124140519.13838-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-01-29 11:46:05 +00:00
Cédric Le Goater
b617ca9223 aspeed/smc: fix default read value
0xFFFFFFFF should be returned for non implemented registers.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190124140519.13838-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-01-29 11:46:05 +00:00
Philippe Mathieu-Daudé
a7e1562ca2 hw/ssi/xilinx_spi: Use DeviceState::realize rather than SysBusDevice::init
Move from the legacy SysBusDevice::init method to using DeviceState::realize.

Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20181002212522.23303-5-f4bug@amsat.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
2018-10-24 06:44:59 -03:00
Cédric Le Goater
b3d6b8f5af aspeed/smc: fix some alignment issues
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180921161939.822-6-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-09-25 15:13:24 +01:00
Peter Maydell
7d3912f54e hw/ssi/pl022: Correct wrong DMACR and ICR handling
In the PL022, register offset 0x20 is the ICR, a write-only
interrupt-clear register.  Register offset 0x24 is DMACR, the DMA
control register.  We were incorrectly implementing (a stub version
of) DMACR at 0x20, and not implementing anything at 0x24.  Fix this
bug.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-21-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
2018-08-24 13:17:46 +01:00
Peter Maydell
139d941e5a hw/ssi/pl022: Correct wrong value for PL022_INT_RT
The PL022 interrupt registers have bits allocated as:
 0: ROR (receive overrun)
 1: RT (receive timeout)
 2: RX (receive FIFO half full or less)
 3: TX (transmit FIFO half full or less)

A cut and paste error meant we had the wrong value for
the PL022_INT_RT constant. This bug doesn't affect device
behaviour, because we don't implement the receive timeout
feature and so never set that interrupt bit.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-20-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
2018-08-24 13:17:46 +01:00
Peter Maydell
13391a563f hw/ssi/pl022: Use DeviceState::realize rather than SysBusDevice::init
Move from the legacy SysBusDevice::init method to using
DeviceState::realize.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-19-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
2018-08-24 13:17:45 +01:00
Peter Maydell
275ff67f40 hw/ssi/pl022: Don't directly call vmstate_register()
Use the DeviceState vmsd pointer rather than calling vmstate_register()
directly.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-18-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
2018-08-24 13:17:45 +01:00
Peter Maydell
66d9aa790f hw/ssi/pl022: Set up reset function in class init
Currently the PL022 calls pl022_reset() from its class init
function. Make it register a DeviceState reset method instead,
so that we reset the device on system reset.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-17-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
2018-08-24 13:17:45 +01:00
Peter Maydell
1d52866f5a hw/ssi/pl022: Allow use as embedded-struct device
Create a new include file for the pl022's device struct,
type macros, etc, so that it can be instantiated using
the "embedded struct" coding style.

While we're adding the new file to MAINTAINERS, add
also the .c file, which was missing an entry.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-16-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
2018-08-24 13:17:44 +01:00
Peter Maydell
5321fa68fd hw/ssi/xilinx_spips: Remove unneeded MMIO request_ptr code
We now support direct execution from MMIO regions in the
core memory subsystem. This means that we don't need to
have device-specific support for it, and we can remove
the request_ptr handling from the Xilinx SPIPS device.
(It was broken anyway due to race conditions, and disabled
by default.)

This device is the only in-tree user of this API.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: KONRAD Frederic <frederic.konrad@adacore.com>
Message-id: 20180817114619.22354-2-peter.maydell@linaro.org
2018-08-20 11:24:32 +01:00
Trent Piepho
016d4b0127 imx_spi: Unset XCH when TX FIFO becomes empty
The current emulation will clear the XCH bit when a burst finishes.
This is not quite correct.  According to the i.MX7d referemce manual,
Rev 0.1, §10.1.7.3:

    This bit [XCH] is cleared automatically when all data in the TXFIFO
    and the shift register has been shifted out.

So XCH should be cleared when the FIFO empties, not on completion of a
burst.  The FIFO is 64 x 32 bits = 2048 bits, while the max burst size
is larger at 4096 bits.  So it's possible that the burst is not finished
after the TXFIFO empties.

Sending a large block (> 2048 bits) with the Linux driver will use a
burst that is larger than the TXFIFO.  After the TXFIFO has emptied XCH
does not become unset, as the burst is not yet finished.

What should happen after the TXFIFO empties is the driver will refill it
and set XCH.  The rising edge of XCH will trigger another transfer to
begin.  However, since the emulation does not set XCH to 0, there is no
rising edge and the next trasfer never begins.

Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Message-id: 20180731201056.29257-1-tpiepho@impinj.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-08-16 14:29:57 +01:00
Philippe Mathieu-Daudé
31a1246df6 hw/ssi/omap_spi: Use qemu_log_mask(GUEST_ERROR) instead of fprintf
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20180624040609.17572-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-06-26 17:50:40 +01:00
Sai Pavan Boddu
21d887cde9 xilinx_spips: Make dma transactions as per dma_burst_size
Qspi dma has a burst length of 64 bytes, So limit the transactions w.r.t
dma-burst-size property.

Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1529660880-30376-1-git-send-email-sai.pavan.boddu@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-06-26 17:50:39 +01:00
Cédric Le Goater
96c4be955b aspeed/smc: rename aspeed_smc_flash_send_addr() to aspeed_smc_flash_setup()
Also handle the fake transfers for dummy bytes in this setup
routine. It will be useful when we activate MMIO execution.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180612065716.10587-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-06-26 17:50:39 +01:00
Cédric Le Goater
a57baeb45e aspeed/smc: fix HW strapping
Only the flash type is strapped by HW. The 4BYTE mode is set by
firmware when the flash device is detected.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180612065716.10587-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-06-26 17:50:39 +01:00
Cédric Le Goater
0721309ed7 aspeed/smc: fix dummy cycles count when in dual IO mode
When configured in dual I/O mode, address and data are sent in dual
mode, including the dummy byte cycles in between. Adapt the count to
the IO setting.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180612065716.10587-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-06-26 17:50:39 +01:00
Marc-André Lureau
265b578c58 object: fix OBJ_PROP_LINK_UNREF_ON_RELEASE ambivalence
A link property can be set during creation, with
object_property_add_link() and later with object_property_set_link().

add_link() doesn't add a reference to the target object, while
set_link() does.

Furthemore, OBJ_PROP_LINK_UNREF_ON_RELEASE flags, set during add_link,
says whether a reference must be released when the property is destroyed.
This can lead to leaks if the property was later set_link(), as the
added reference is never released.

Instead, rename OBJ_PROP_LINK_UNREF_ON_RELEASE to OBJ_PROP_LINK_STRONG
and use that has an indication on how the link handle reference
management in set_link().

Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180531195119.22021-3-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
2018-06-12 12:07:30 +02:00