Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20231028122415.14869-5-shentey@gmail.com
[PMM: Add "Hz" unit indicator to frequency traces]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20231028122415.14869-4-shentey@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
NetBSD assumes it can send its first ADB command after sending the ADB_BUSRESET
command in ADB_STATE_NEW without changing the state back to ADB_STATE_IDLE
first as detailed in the ADB protocol.
Add a workaround to detect this condition at the start of ADB enumeration
and send the next command written to SR after a ADB_BUSRESET onto the bus
regardless, even if we don't detect a state transition to ADB_STATE_NEW.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-ID: <20231004083806.757242-16-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The MacOS toolbox ROM calculates the number of branches that can be executed
per millisecond as part of its timer calibration. Since modern hosts are
considerably quicker than original hardware, the negative counter reaches zero
before the calibration completes leading to division by zero later in
CALCULATESLOD.
Instead of trying to fudge the timing loop (which won't work for TimeDBRA/TimeSCCDB
anyhow), use the pattern of access to the VIA1 registers to detect when SETUPTIMEK
has finished executing and write some well-known good timer values to TimeDBRA
and TimeSCCDB taken from real hardware with a suitable scaling factor.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-ID: <20231004083806.757242-15-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
It is needed because it defines the BIOSConfig area.
Co-developed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-ID: <20231004083806.757242-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The djMEMC controller is used to store information related to the physical memory
configuration.
Co-developed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20231004083806.757242-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The SRC device is normally used to start the secondary CPU.
When running Linux directly, QEMU is emulating a PSCI interface that UBOOT
is installing at boot time and therefore the fact that the SRC device is
unimplemented is hidden as Qemu respond directly to PSCI requets without
using the SRC device.
But if you try to run a more bare metal application (maybe uboot itself),
then it is not possible to start the secondary CPU as the SRC is an
unimplemented device.
This patch adds the ability to start the secondary CPU through the SRC
device so that you can use this feature in bare metal applications.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: ce9a0162defd2acee5dc7f8a674743de0cded569.1692964892.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Only a few important registers are added, especially the SRAM_VER
register.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Types of memory that the SDRAM controller supports are DDR2/DDR3
and capacities of up to 2GiB. This commit adds emulation support
of the Allwinner R40 SDRAM controller.
This driver only support 256M, 512M and 1024M memory now.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds minimal support for AXP-221 PMU and connect it to
bananapi M2U board.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds minimal support for AXP-209 PMU.
Most important is chip ID since U-Boot SPL expects version 0x1. Besides
the chip ID register, reset values for two more registers used by A10
U-Boot SPL are covered.
Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Message-id: 20221226220303.14420-5-strahinja.p.jankovic@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In real hardware, the APB and AHB PNP data tables can be accessed
with byte and halfword reads as well as word reads. Our
implementation currently only handles word reads. Add support for
the 8 and 16 bit accesses. Note that we only need to handle aligned
accesses -- unaligned accesses should continue to trap, as happens on
hardware.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1132
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Frederic Konrad <fkonrad@amd.com>
Message-Id: <20220802131925.3380923-1-peter.maydell@linaro.org>
Tested-by: Tomasz Martyniak <gitlab.com/tom4r>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This introduces a really basic PECI controller that responses to
commands by always setting the response code to success and then raising
an interrupt to indicate the command is done. This helps avoid getting
hit with constant errors if the driver continuously attempts to send a
command and keeps timing out.
The AST2400 and AST2500 only included registers up to 0x5C, not 0xFC.
They supported PECI 1.1, 2.0, and 3.0. The AST2600 and AST1030 support
PECI 4.0, which includes more read/write buffer registers from 0x80 to
0xFC to support 64-byte mode.
This patch doesn't attempt to handle that, or to create a different
version of the controller for the different generations, since it's only
implementing functionality that is common to all generations.
The basic sequence of events is that the firmware will read and write to
various registers and then trigger a command by setting the FIRE bit in
the command register (similar to the I2C controller).
Then the firmware waits for an interrupt from the PECI controller,
expecting the interrupt status register to be filled in with info on
what happened. If the command was transmitted and received successfully,
then response codes from the host CPU will be found in the data buffer
registers.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-12-me@pjd.dev>
[ clg: s/sysbus_mmio_map/aspeed_mmio_map/ ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Move the LASI device implementation from hw/hppa to hw/misc so that it is
located with all the other miscellaneous devices.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20220504092600.10048-43-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
"0x%u" format is very misleading, replace by "0x%x".
Found running:
$ git grep -E '0x%[0-9]*([lL]*|" ?PRI)[dDuU]' hw/
Inspired-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-id: 20220323114718.58714-3-philippe.mathieu.daude@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This helps to follow how the guest is programming the mos6522 when debugging.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220305150957.5053-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This is useful to analyze changes in the U-Boot RAM driver when SDRAM
training is performed.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Aspeed 2600 SDK enables I3C support by default. The I3C driver will try
to reset the device controller and set it up through device address table
register. This dummy model responds to these registers with default values
as listed in the ast2600v10 datasheet chapter 54.2.
This avoids a guest machine kernel panic due to referencing an
invalid kernel address if the device address table register isn't
set correctly.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Reviewed-by: Graeme Gregory <quic_ggregory@quicinc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Graeme Gregory <quic_ggregory@quicinc.com>
Message-id: 20220111084546.4145785-2-troy_lee@aspeedtech.com
[PMM: tidied commit message; fixed format strings]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a new auxmode GPIO that is updated when port B bit 6 is changed indicating
whether the hardware is configured for A/UX mode.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211020134131.4392-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Commit e50caf4a5c ("tracing: convert documentation to rST")
converted docs/devel/tracing.txt to docs/devel/tracing.rst.
We still have several references to the old file, so let's fix them
with the following command:
sed -i s/tracing.txt/tracing.rst/ $(git grep -l docs/devel/tracing.txt)
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210517151702.109066-2-sgarzare@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Target lm32 was deprecated in commit d849800512, v5.2.0. See there
for rationale.
Some of its code lives on in device models derived from milkymist
ones: hw/char/digic-uart.c and hw/display/bcm2835_fb.c.
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210503084034.3804963-2-armbru@redhat.com>
Acked-by: Michael Walle <michael@walle.cc>
[Trivial conflicts resolved, reST markup fixed]
Since all the documentation uses the hex offsets, this makes it much easier
to see what is going on.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210311100505.22596-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Add a system controller for the m68k-virt machine.
This controller allows the kernel to power off or reset the machine.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210312214145.2936082-5-laurent@vivier.eu>
This patch implements Multi Function Timer (MFT) module for NPCM7XX.
This module is mainly used to configure PWM fans. It has just enough
functionality to make the PWM fan kernel module work.
The module takes two input, the max_rpm of a fan (modifiable via QMP)
and duty cycle (a GPIO from the PWM module.) The actual measured RPM
is equal to max_rpm * duty_cycle / NPCM7XX_PWM_MAX_DUTY. The RPM is
measured as a counter compared to a prescaled input clock. The kernel
driver reads this counter and report to user space.
Refs:
https://github.com/torvalds/linux/blob/master/drivers/hwmon/npcm750-pwm-fan.c
Reviewed-by: Doug Evans <dje@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210311180855.149764-3-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
An assorted set of spelling fixes in various places.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210309111510.79495-1-mjt@msgid.tls.msk.ru>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The SSE-300 has a new register block CPU<N>_PWRCTRL. There is one
instance of this per CPU in the system (so just one for the SSE-300),
and as well as the usual CIDR/PIDR ID registers it has just one
register, CPUPWRCFG. This register allows the guest to configure
behaviour of the system in power-down and deep-sleep states. Since
QEMU does not model those, we make the register a dummy
reads-as-written implementation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-21-peter.maydell@linaro.org
The PWM module is part of NPCM7XX module. Each NPCM7XX module has two
identical PWM modules. Each module contains 4 PWM entries. Each PWM has
two outputs: frequency and duty_cycle. Both are computed using inputs
from software side.
This module does not model detail pulse signals since it is expensive.
It also does not model interrupts and watchdogs that are dependant on
the detail models. The interfaces for these are left in the module so
that anyone in need for these functionalities can implement on their
own.
The user can read the duty cycle and frequency using qom-get command.
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210108190945.949196-5-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The BCM2835 CPRMAN is the clock manager of the SoC. It is composed of a
main oscillator, and several sub-components (PLLs, multiplexers, ...) to
generate the BCM2835 clock tree.
This commit adds a skeleton of the CPRMAN, with a dummy register
read/write implementation. It embeds the main oscillator (xosc) from
which all the clocks will be derived.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The RNG module returns a byte of randomness when the Data Valid bit is
set.
This implementation ignores the prescaler setting, and loads a new value
into RNGD every time RNGCS is read while the RNG is enabled and random
data is available.
A qtest featuring some simple randomness tests is included.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Per the 'ARM MPS2 and MPS2+ FPGA Prototyping Boards Technical
Reference Manual' (100112_0200_07_en):
2.1 Overview of the MPS2 and MPS2+ hardware
The MPS2 and MPS2+ FPGA Prototyping Boards contain the
following components and interfaces:
* User switches and user LEDs:
- Two green LEDs and two push buttons that connect to
the FPGA.
- Eight green LEDs and one 8-way dip switch that connect
to the MCC.
Add the 8 LEDs connected to the MCC.
This replaces the 'mps2_scc_leds' trace events by the generic
'led_set_intensity' event.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-Id: <20200912134041.946260-7-f4bug@amsat.org>
Per the 'ARM MPS2 and MPS2+ FPGA Prototyping Boards Technical
Reference Manual' (100112_0200_07_en):
2.1 Overview of the MPS2 and MPS2+ hardware
The MPS2 and MPS2+ FPGA Prototyping Boards contain the
following components and interfaces:
* User switches and user LEDs:
- Two green LEDs and two push buttons that connect to
the FPGA.
- Eight green LEDs and one 8-way dip switch that connect
to the MCC.
Add the 2 LEDs connected to the FPGA.
This replaces the 'mps2_fpgaio_leds' trace events by the generic
'led_set_intensity' event.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-Id: <20200912134041.946260-6-f4bug@amsat.org>
Track the LED intensity, and emit a trace event when it changes.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200912134041.946260-4-f4bug@amsat.org>
Add a LED device which can be connected to a GPIO output.
They can also be dimmed with PWM devices. For now we do
not implement the dimmed mode, but in preparation of a
future implementation, we start using the LED intensity.
LEDs are limited to a fixed set of colors.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200912134041.946260-2-f4bug@amsat.org>
Enough functionality to boot the Linux kernel has been implemented. This
includes:
- Correct power-on reset values so the various clock rates can be
accurately calculated.
- Clock enables stick around when written.
In addition, a best effort attempt to implement SECCNT and CNTR25M was
made even though I don't think the kernel needs them.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-3-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement a device model for the System Global Control Registers in the
NPCM730 and NPCM750 BMC SoCs.
This is primarily used to enable SMP boot (the boot ROM spins reading
the SCRPAD register) and DDR memory initialization; other registers are
best effort for now.
The reset values of the MDLR and PWRON registers are determined by the
SoC variant (730 vs 750) and board straps respectively.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-2-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some trace points are attributed to the wrong source file. Happens
when we neglect to update trace-events for code motion, or add events
in the wrong place, or misspell the file name.
Clean up with help of scripts/cleanup-trace-events.pl. Funnies
requiring manual post-processing:
* accel/tcg/cputlb.c trace points are in trace-events.
* block.c and blockdev.c trace points are in block/trace-events.
* hw/block/nvme.c uses the preprocessor to hide its trace point use
from cleanup-trace-events.pl.
* hw/tpm/tpm_spapr.c uses pseudo trace point tpm_spapr_show_buffer to
guard debug code.
* include/hw/xen/xen_common.h trace points are in hw/xen/trace-events.
* linux-user/trace-events abbreviates a tedious list of filenames to
*/signal.c.
* net/colo-compare and net/filter-rewriter.c use pseudo trace points
colo_compare_miscompare and colo_filter_rewriter_debug to guard
debug code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200806141334.3646302-5-armbru@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Tracked down with the help of scripts/cleanup-trace-events.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20200806141334.3646302-4-armbru@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This is a simple device of just one register, and whenever this
register is written to it calls qemu_set_irq function for each
of 8 bits/IRQs. It is used to implement AVR Power Reduction.
[AM: Remove word 'Atmel' from filenames and all elements of code]
Suggested-by: Aleksandar Markovic <aleksandar.m.mail@gmail.com>
Signed-off-by: Michael Rolnik <mrolnik@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[rth: Squash include fix and file rename from f4bug]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Aleksandar Markovic <aleksandar.m.mail@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Message-Id: <20200705140315.260514-22-huth@tuxfamily.org>
The existing ADB state machine is designed to work with Linux which has a different
interpretation of the state machine detailed in "Guide to the Macintosh Family
Hardware". In particular the current Linux implementation includes an extra change
to IDLE state when switching the VIA between send and receive modes which does not
occur in MacOS, and omitting this transition causes the current mac_via ADB state
machine to fail.
Rework the ADB state machine accordingly so that it can enumerate and autopoll the
ADB under both Linux and MacOS, including the addition of the new adb_autopoll_block()
and adb_autopoll_unblock() functions.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20200623204936.24064-20-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: KONRAD Frederic <frederic.konrad@adacore.com>
Message-Id: <20200331105048.27989-5-f4bug@amsat.org>
Add an entry for the 'empty_slot' device.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
Message-Id: <20200510152840.13558-7-f4bug@amsat.org>
In the Allwinner H3 SoC the SDRAM controller is responsible
for interfacing with the external Synchronous Dynamic Random
Access Memory (SDRAM). Types of memory that the SDRAM controller
supports are DDR2/DDR3 and capacities of up to 2GiB. This commit
adds emulation support of the Allwinner H3 SDRAM controller.
Signed-off-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20200311221854.30370-12-nieklinnenbank@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
