b,gate does GR[t] ← cat(GR[t]{0..29},IAOQ_Front{30..31});
instead of saving the link address to register t.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190311191602.25796-8-svens@stackframe.org>
[rth: Move link check outside of ifndef CONFIG_USER_ONLY;
use ctx->privilege; nullify the insn earlier.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
DIAG is usually only used by diagnostics software as it's CPU
specific. In most of the cases it's better to ignore it and log
a message that it's not implemented.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190311191602.25796-7-svens@stackframe.org>
[rth: Free the nullify condition.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
HP ODE use rfi to set the Q bit, and i don't see anything in the
documentation that this is forbidden. So remove it.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190311191602.25796-6-svens@stackframe.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
To ease TLB debugging add a few trace events, which are disabled
by default so that there's no performance impact.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190311191602.25796-5-svens@stackframe.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190311191602.25796-4-svens@stackframe.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Assume the following sequence:
pitlbe r0(sr0,r0)
iitlba r4,(sr0,r0)
ldil L%3000000,r5
iitlbp r5,(sr0,r0)
This will purge the whole TLB and add an entry for page 0. However
the current TLB implementation in helper_iitlba() will store to
the last empty TLB entry, while helper_iitlbp() will write to the
first empty entry. That is because an empty entry will match address
0 in helper_iitlba()
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190311191602.25796-3-svens@stackframe.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
When one of the source registers is the same as the destination register,
the source register gets overwritten with the destionation value before
do_add_sv() is called, which leads to unexpection condition matches.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190311191602.25796-2-svens@stackframe.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We got away with eliding this check when target/hppa was user-only,
but missed adding this check when adding system support.
Fixes an early crash in the HP-UX 11 installer.
Reported-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We can eliminate an extra TB in this case, which merely
loads a "return address" into rn.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
For priv levels 1 & 2, we were doing so from do_ibranch_priv.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
It looks like the operands where exchanged. HP bootrom tests the
following sequence:
0x00000000f0004064: ldil L%-66666800,r7
0x00000000f0004068: addi 19f,r7,r7
0x00000000f000406c: addi -1,r0,rp
0x00000000f0004070: addi f,r0,r4
0x00000000f0004074: addi 1,r4,r5
0x00000000f0004078: dcor rp,r6
0x00000000f000407c: cmpb,<>,n r6,r7,0xf000411
This returned 0x66666661 instead of the expected 0x9999999f in QEMU.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190211181907.2219-6-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
These conditions include the signed overflow bit. See page 5-3
of the Parisc 1.1 Architecture Reference Manual for details.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
[rth: More changes for c == 3, to compute (N^V)|Z properly.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We will be fixing do_cond vs signed overflow, which requires
that do_log_cond not rely on do_cond.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
When QEMU is compiled with -O0, these functions are inlined
which will cause a wrong restart address generated for the TB.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190211181907.2219-2-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Now that the implementation is entirely within the generated
decode function, eliminate the wrapper.
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
With decodetree.py, the specializations would conflict so we
must have a single entry point for all variants of OR.
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Convert the BREAK instruction to start.
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Instead of returning DisasJumpType, immediately store it.
Return true in preparation for conversion to the decodetree script.
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
PA-RISC specification says: "Setting the PSW Q-bit, PSW{28}, to 1
with this instruction, if it was not already 1, is an undefined
operation." However, at least HP-UX 10.20 sets the Q bit from 0 to 1
with the SSM instruction. Tested this both on HP9000/712 and
HP9000/785/C3750, both machines set the Q bit from 0 to 1 without
exception. This makes HP-UX 10.20 progress a little bit further.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190129191402.29539-1-svens@stackframe.org>
[rth: Add a comment to the code as well.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
While doing 'set $pcoqh=0xf0000000' i triggered the assertion below.
The argument order for deposit64() is wrong, and val needs to be
moved to the end.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190128165333.3814-1-svens@stackframe.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Because they are supposed to remain const.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20181114132931.22624-1-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On PCXS chips (PA7000, pa 1.1a), trap #18 is raised on memory faults,
while all later chips (>= PA7100) generate either trap #26, #27 or #28
(depending on the fault type).
Since the current qemu emulation emulates a B160L machine (with a
PA7300LC PCX-L2 chip, we should raise trap #26 (EXCP_DMAR) instead
of #18 (EXCP_DMP) on access faults by the Linux kernel to page zero.
With the patch we now get the correct output (I tested against real
hardware):
Kernel Fault: Code=26 (Data memory access rights trap)
instead of:
Kernel Fault: Code=18 (Data memory protection/unaligned access trap)
Signed-off-by: Helge Deller <deller@gmx.de>
Message-Id: <20181007205153.GA30270@ls3530.fritz.box>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Do the cast to uintptr_t within the helper, so that the compiler
can type check the pointer argument. We can also do some more
sanity checking of the index argument.
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Since his inception in 61766fe9e2, this file uses the qemu_log()
API from "qemu/log.h". Include it to allow further includes
cleanup.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-9-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Only MIPS requires snan_bit_is_one to be variable. While we are
specializing softfloat behaviour, allow other targets to eliminate
this runtime check.
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Yongbok Kim <yongbok.kim@mips.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Alexander Graf <agraf@suse.de>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This is now handled properly by the generic softfloat code.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
While at it, use int for both num_insns and max_insns to make
sure we have same-type comparisons.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Drop TCGV_PTR_TO_NAT and TCGV_NAT_TO_PTR internal macros.
Add tcg_temp_local_new_ptr, tcg_gen_brcondi_ptr, tcg_gen_ext_i32_ptr,
tcg_gen_trunc_i64_ptr, tcg_gen_extu_ptr_i64, tcg_gen_trunc_ptr_i32.
Use inlines instead of macros where possible.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
A recent glibc change relies on the fact that the iaoq must be 3,
and computes an address based on that. QEMU had been ignoring the
priv level for user-only, which produced an incorrect address.
Reported-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
cpu_init(cpu_model) were replaced by cpu_create(cpu_type) so
no users are left, remove it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au> (ppc)
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1518000027-274608-6-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
it will be used for providing to cpu name resolving class for
parsing cpu model for system and user emulation code.
Along with change add target to null-machine tests, so
that when switch to CPU_RESOLVING_TYPE happens,
it would ensure that null-machine usecase still works.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu> (m68k)
Acked-by: David Gibson <david@gibson.dropbear.id.au> (ppc)
Acked-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de> (tricore)
Message-Id: <1518000027-274608-4-git-send-email-imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
[ehabkost: Added macro to riscv too]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Unify half a dozen copies of very similar code (the only difference being
whether comparisons were case-sensitive) and use it also in Tricore,
which did not do any sorting of CPU model names.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
