While we set env->bins when unwinding for ILLEGAL_INST,
from e.g. csrrw, we weren't setting it for immediately
illegal instructions.
Add a testcase for mtval via both exception paths.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1060
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220604231004.49990-2-richard.henderson@linaro.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Commit 57c108b864 introduced gen_set_gpri(), which already contains
a check for if the destination register is 'zero'. The check in auipc
and lui are then redundant. This patch removes those checks.
Signed-off-by: Víctor Colombo <victor.colombo@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220610165517.47517-1-victor.colombo@eldorado.org.br>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
In the last series, I inadvertantly didn't remove this inline, but did
all the others. Remove it for consistency.
Signed-off-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
These implement both the old-pre INO64 mknod variations, as well as the
now current INO64 variant. Make direct syscall calls for these older
syscalls to avloid too many dependencies.
Signed-off-by: Stacey Son <sson@FreeBSD.org>
Signed-off-by: Michal Meloun <mmel@FreeBSD.org>
Signed-off-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Stacey Son <sson@FreeBSD.org>
Signed-off-by: Jung-uk Kim <jkim@FreeBSD.org>
Signed-off-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Stacey Son <sson@FreeBSD.org>
Signed-off-by: Jung-uk Kim <jkim@FreeBSD.org>
Signed-off-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Canokey core currently using 16 bytes as maximum packet size for
control endpoint, but to run the device in high-speed a 64 bytes
maximum packet size is required according to USB 2.0 specification.
Since we don't acutally need to run the device in high-speed, simply
don't assign high member in USBDesc.
When canokey-qemu is used with xhci, xhci would drive canokey
in high speed mode, since the bcdUSB in canokey-core is 2.1,
yet canokey-core set bMaxPacketSize0 to be 16, this is out
of the spec as the spec said that ``The allowable maximum
control transfer data payload sizes...for high-speed devices,
it is 64 bytes''.
In this case, usb device validation in Windows 10 LTSC 2021
as the guest would fail. It would complain
USB\DEVICE_DESCRIPTOR_VALIDATION_FAILURE.
Note that bcdUSB only identifies the spec version the device
complies, but it has no indication of its speed. So it is
allowed for the device to run in FS but comply the 2.1 spec.
To solve the issue we decided to just drop the high
speed support. This only affects usb-ehci as usb-ehci would
complain speed mismatch when FS device is attached to a HS port.
That's why the .high member was initialized in the first place.
Meanwhile, xhci is not affected as it works well with FS device.
Since everyone is now using xhci, it does no harm to most users.
Suggested-by: Hongren (Zenithal) Zheng <i@zenithal.me>
Signed-off-by: YuanYang Meng <mkfssion@mkfssion.com>
Reviewed-by: Hongren (Zenithal) Zheng <i@zenithal.me>
Message-Id: <20220625142138.19363-1-mkfssion@mkfssion.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
CCID could send zero-length packet (ZLP)
if we invoke two data_in, two packets would be concated
and we could not distinguish them.
The CANOKEY_EMU_EP_CTAPHID is imported from canokey-qemu.h
Reported-by: MkfsSion <myychina28759@gmail.com>
Signed-off-by: Hongren (Zenithal) Zheng <i@zenithal.me>
Message-Id: <YqcqGz0s3+LE42ms@Sun>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
[-NSPasteboard dataForType:] returns an autoreleased NSString,
and callings its release method will result in double-free when
the global autorelease pool is released. Use NSAutoreleasePool to
release it properly.
Signed-off-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220614212131.94696-1-akihiko.odaki@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The update makes it easier to find and specify devices.
They can only be found by device type name without the id field,
for example, devices of the same type have the same label.
The update also adds a head field,
which is useful for devices that support multiple heads,
such as virtio-gpu.
Signed-off-by: Jianxian Wen <jianxian.wen@verisilicon.com>
Signed-off-by: Lu Gao <lu.gao@verisilicon.com>
Message-Id: <4C23C17B8E87E74E906A25A3254A03F4018FC045B0@SHASXM06.verisilicon.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
And add it to specs/index.rst
Signed-off-by: Simon Sapin <simon.sapin@exyr.org>
Message-Id: <20220625161455.1232954-2-simon.sapin@exyr.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This is a separate commit in order to make reviewing the next one easier.
Signed-off-by: Simon Sapin <simon.sapin@exyr.org>
Message-Id: <20220625161455.1232954-1-simon.sapin@exyr.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
* m25p80 improvements (Iris)
* Code cleanup in preparation of multi SoC machine (Peter)
* New MAX31785 model (Mahesh)
* New Qualcomm machines (Jae and Graeme)
* Core I2C slave mode (Klaus)
* Aspeed I2C slave mode for old and new register interface (Peter and Klaus)
* New Aspeed PECI model (Peter)
* Various small fixes
-----BEGIN PGP SIGNATURE-----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=oUKu
-----END PGP SIGNATURE-----
Merge tag 'pull-aspeed-20220630' of https://github.com/legoater/qemu into staging
aspeed queue:
* m25p80 improvements (Iris)
* Code cleanup in preparation of multi SoC machine (Peter)
* New MAX31785 model (Mahesh)
* New Qualcomm machines (Jae and Graeme)
* Core I2C slave mode (Klaus)
* Aspeed I2C slave mode for old and new register interface (Peter and Klaus)
* New Aspeed PECI model (Peter)
* Various small fixes
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmK9UfQACgkQUaNDx8/7
# 7KFYWhAAtlx3aaEacrn/ONNHjk6G9Fxku56gAbaIiuiaIWNOj3/T2frPsnmbO8x8
# EKrgUYB8i8PFve/fJYA5vZUzIddPTaHkULZ12JQoGVg0L9hDBbizslN5lJWRXoSv
# 9r3DF9nahzLKRNvzoBfuKjHDQ2cwHoFgYmKmlYpDcgfmBcl16uzZy8jvxg/Tghur
# umH4IJMjeDNz/kLfINoO/m+kuFPVXmbTJNwl8uK5MUVDTgVSqharywWlUizugBVH
# StLE+GmBPylTuYXyiOzLTkoGJeeHp3sQ1DmyI4DD83odjnfxa0BGMGDVhD35exXi
# 9tLY9FgQ4smATuyN0UGAKZTBmzpI+ov0HMzvH4lUMR8i8daBuEet3RVr/DqkOP4h
# LEVTRWTaTJip24ohgw4K/b86pI9nTJWVPGV56eZGYmnqufnvf/upNU65/nCsF/xD
# i1TdS+zJWxhjgGEepg9cTmxxUlA4jVNNbl6dvAgS5Jr6Igrd1BlCSXjmyhO3NRPZ
# bgOuvCb3RyxAY4+/9wphx2/t5X2VIU6R8EAjnh+7nIgBhOQU5SZ6uefFVYZq8xx+
# IYEDHj3saiRa4FHmyOgeRxRaQj/Vvs83PPti2rPmJuieqiClJmbE+XfTIamoxVIv
# 5USlKmMRRVI69MjsjwFi/gOaV/N1EUgcFoYbnvwZ+Md3fg5+70M=
# =oUKu
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 30 Jun 2022 01:04:12 PM +0530
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-aspeed-20220630' of https://github.com/legoater/qemu: (27 commits)
hw/misc/aspeed: Add PECI controller
hw/i2c/aspeed: Add new-registers DMA slave mode RX support
hw/i2c/aspeed: add slave device in old register mode
hw/i2c: add asynchronous send
hw/i2c: support multiple masters
hw/i2c/aspeed: Fix MASTER_EN missing error message
hw/i2c/aspeed: Fix DMA len write-enable bit handling
hw/i2c/aspeed: Fix R_I2CD_FUN_CTRL reference
hw/arm/aspeed: firework: add I2C MUXes for VR channels
hw/arm/aspeed: firework: Add Thermal Diodes
hw/arm/aspeed: Add MAX31785 Fan controllers
hw/sensor: add Maxim MAX31785 device
hw/i2c: pmbus: Page #255 is valid page for read requests.
hw/arm/aspeed: add Qualcomm Firework BMC machine
hw/arm/aspeed: add support for the Qualcomm DC-SCM v1 board
aspeed: Remove use of qemu_get_cpu
aspeed: Map unimplemented devices in SoC memory
aspeed: Remove usage of sysbus_mmio_map
aspeed: Add memory property to Aspeed SoC
aspeed: Set CPU memory property explicitly
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This introduces a really basic PECI controller that responses to
commands by always setting the response code to success and then raising
an interrupt to indicate the command is done. This helps avoid getting
hit with constant errors if the driver continuously attempts to send a
command and keeps timing out.
The AST2400 and AST2500 only included registers up to 0x5C, not 0xFC.
They supported PECI 1.1, 2.0, and 3.0. The AST2600 and AST1030 support
PECI 4.0, which includes more read/write buffer registers from 0x80 to
0xFC to support 64-byte mode.
This patch doesn't attempt to handle that, or to create a different
version of the controller for the different generations, since it's only
implementing functionality that is common to all generations.
The basic sequence of events is that the firmware will read and write to
various registers and then trigger a command by setting the FIRE bit in
the command register (similar to the I2C controller).
Then the firmware waits for an interrupt from the PECI controller,
expecting the interrupt status register to be filled in with info on
what happened. If the command was transmitted and received successfully,
then response codes from the host CPU will be found in the data buffer
registers.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-12-me@pjd.dev>
[ clg: s/sysbus_mmio_map/aspeed_mmio_map/ ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This commit adds support for DMA RX in slave mode while using the new
register set in the AST2600 and AST1030. This patch also pretty much
assumes packet mode is enabled, I'm not sure if this will work in DMA
step mode.
This is particularly useful for testing IPMB exchanges between Zephyr
and external devices, which requires multi-master I2C support and DMA in
the new register mode, because the Zephyr drivers from Aspeed use DMA in
the new mode by default. The Zephyr drivers are also using packet mode.
The typical sequence of events for receiving data in DMA slave + packet
mode is that the Zephyr firmware will configure the slave address
register with an address to receive on and configure the bus's function
control register to enable master mode and slave mode simultaneously at
startup, before any transfers are initiated.
RX DMA is enabled in the slave mode command register, and the slave RX
DMA buffer address and slave RX DMA buffer length are set. TX DMA is not
covered in this patch.
When the Aspeed I2C controller receives data from some other I2C master,
it will reset the I2CS_DMA_LEN RX_LEN value to zero, then buffer
incoming data in the RX DMA buffer while incrementing the I2CC_DMA_ADDR
address counter and decrementing the I2CC_DMA_LEN counter. It will also
update the I2CS_DMA_LEN RX_LEN value along the way.
Once all the data has been received, the bus controller will raise an
interrupt indicating a packet command was completed, the slave address
matched, a normal stop condition was seen, and the transfer was an RX
operation.
If the master sent a NACK instead of a normal stop condition, or the
transfer timed out, then a slightly different set of interrupt status
values would be set. Those conditions are not handled in this commit.
The Zephyr firmware then collects data from the RX DMA buffer and clears
the status register by writing the PKT_MODE_EN bit to the status
register. In packet mode, clearing the packet mode interrupt enable bit
also clears most of the other interrupt bits automatically (except for a
few bits above it).
Note: if the master transmit or receive functions were in use
simultaneously with the slave mode receive functionality, then the
master mode functions may have raised the interrupt line for the bus
before the DMA slave transfer is complete. It's important to have the
slave's interrupt status register clear throughout the receive
operation, and if the slave attempts to raise the interrupt before the
master interrupt status is cleared, then it needs to re-raise the
interrupt once the master interrupt status is cleared. (And vice-versa).
That's why in this commit, when the master interrupt status is cleared
and the interrupt line is lowered, we call the slave interrupt _raise_
function, to see if the interrupt was pending. (And again, vice-versa).
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220630045133.32251-8-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add slave mode functionality for the Aspeed I2C controller in old
register mode. This is implemented by realizing an I2C slave device
owned by the I2C controller and attached to its own bus.
The I2C slave device only implements asynchronous sends on the bus, so
slaves not supporting that will not be able to communicate with it.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg: checkpatch fixes ]
Message-Id: <20220601210831.67259-6-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-7-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add an asynchronous version of i2c_send() that requires the slave to
explicitly acknowledge on the bus with i2c_ack().
The current master must use the new i2c_start_send_async() to indicate
that it wants to do an asynchronous transfer. This allows the i2c core
to check if the target slave supports this or not. This approach relies
on adding a new enum i2c_event member, which is why a bunch of other
devices needs changes in their event handling switches.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20220601210831.67259-5-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-6-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Allow slaves to master the bus by registering a bottom halve. If the bus
is busy, the bottom half is queued up. When a slave has succesfully
mastered the bus, the bottom half is scheduled.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg : - fixed typos in commit log ]
Message-Id: <20220601210831.67259-4-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-5-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
aspeed_i2c_bus_is_master is checking if master mode is enabled in the I2C
bus controller's function-control register, not that slave mode is enabled
or something. The error here is that the guest is trying to trigger an I2C
master mode command while master mode is not enabled.
Fixes: ba2cccd64e ("aspeed: i2c: Add new mode support")
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220630045133.32251-4-me@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
I noticed i2c rx transfers were getting shortened to "1" on Zephyr. It
seems to be because the Zephyr i2c driver sets the RX DMA len with the
RX field write-enable bit set (bit 31) to avoid a read-modify-write. [1]
/* 0x1C : I2CM Master DMA Transfer Length Register */
I think we should be checking the write-enable bits on the incoming
value, not checking the register array. I'm not sure we're even writing
the write-enable bits to the register array, actually.
[1] db3dbcc9c5/drivers/i2c/i2c_aspeed.c (L145-L148)
Fixes: ba2cccd64e ("aspeed: i2c: Add new mode support")
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220630045133.32251-3-me@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Very minor, doesn't effect functionality, but this is supposed to be
R_I2CC_FUN_CTRL (new-mode, not old-mode).
Fixes: ba2cccd64e ("aspeed: i2c: Add new mode support")
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220630045133.32251-2-me@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add MAX31785 fan controllers in machines so that the Linux driver
populates the sysfs interface.
Firework has two MAX31785 Fan controllers at 0x52, and 0x54 on bus 9.
Witherspoon has one at 0x52 on bus 3.
Rainier has one at 0x52 on bus 7.
Signed-off-by: Maheswara Kurapati <quic_mkurapat@quicinc.com>
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220627154703.148943-6-quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
MAX31785 is a PMBus compliant 6-Channel fan controller. It supports 6 fan
channels, 11 temperature sensors, and 6-Channel ADC to measure the remote
voltages. Datasheet can be found here:
https://datasheets.maximintegrated.com/en/ds/MAX31785.pdf
This initial version of the driver has skeleton and support for the
fan channels. Requests for temperature sensors, and ADC Channels the
are serviced with the default values as per the datasheet. No additional
instrumentation is done. NV Log feature is not supported.
Signed-off-by: Maheswara Kurapati <quic_mkurapat@quicinc.com>
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220627154703.148943-5-quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Current implementation of the pmbus core driver treats the read request
for page 255 as invalid request and sets the invalid command bit (bit 7)
in the STATUS_CML register. As per the PMBus specification it is a valid
request.
Refer to the PMBus specification, revision 1.3.1, section 11.10 PAGE,
on the page 58:
"Setting the PAGE to FFh means that all subsequent comands are to be
applied to all outputs.
Some commands, such as READ_TEMPERATURE, may use a common sensor but
be available on all pages of a device. Such implementations are the
decision of each device manufacturer or are specified in a PMBus
Application Profile. Consult the manufacturer's documents or the
Application Profile Specification as needed."
For e.g.,
The VOUT_MODE is a valid command for page 255 for maxim 31785 device.
refer to Table 1. PMBus Command Codes on page 14 in the datasheet.
https://datasheets.maximintegrated.com/en/ds/MAX31785.pdf
Fixes: 38870253f1 ("hw/i2c: pmbus: fix error returns and guard against out of range accesses")
Signed-off-by: Maheswara Kurapati <quic_mkurapat@quicinc.com>
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220627154703.148943-4-quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
sysbus_mmio_map maps devices into "get_system_memory()".
With the new SoC memory attribute, we want to make sure that each device is
mapped into the SoC memory.
In single SoC machines, the SoC memory is the same as "get_system_memory()",
but in multi SoC machines it will be different.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220624003701.1363500-4-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Multi-SoC machines can use this property to specify a memory container
for each SoC. Single SoC machines will just specify get_system_memory().
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220624003701.1363500-3-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Coverity warns that "ssi_transfer(s->spi, 0U) << 8 * i" might overflow
because the expression is evaluated using 32-bit arithmetic and then
used in a context expecting a uint64_t.
Fixes: Coverity CID 1487244
Message-Id: <20220628165512.1133590-1-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
While the HMAC mode is not modelled, the accumulative mode is.
Accumulative mode is enabled by setting one of the bits in the HMAC
engine command mode part of the register, so fix the unimplemented check
to only look at the upper of the two bits.
Fixes: 5cd7d8564a ("aspeed/hace: Support AST2600 HACE")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220627100816.125956-1-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Using a 'stop' string seems more appropriate than 'normal'.
Reviewed-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220628154740.1117349-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Currently, the Aspeed machines allocate a ram container region in
which the machine ram region is mapped. See commit ad1a978218
("aspeed: add a RAM memory region container"). An extra region is
mapped after ram in the ram container to catch invalid access done by
FW. That's how FW determines the size of ram. See commit ebe31c0a8e
("aspeed: add a max_ram_size property to the memory controller").
Let's move all the logic under the SoC where it should be. It will
also ease the work on multi SoC support.
Reviewed-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220623202123.3972977-1-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
