A set of SPI flash slaves is attached under the flash controllers of
the palmetto platform. "n25q256a" flash modules are used for the BMC
and "mx25l25635e" for the host. These types are common in the
OpenPower ecosystem.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-9-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Each controller on the ast2400 has a memory range on which it maps its
flash module slaves. Each slave is assigned a memory segment for its
mapping that can be changed at bootime with the Segment Address
Register. This is not supported in the current implementation so we
are using the defaults provided by the specs.
Each SPI flash slave can then be accessed in two modes: Command and
User. When in User mode, accesses to the memory segment of the slaves
are translated in SPI transfers. When in Command mode, the HW
generates the SPI commands automatically and the memory segment is
accessed as if doing a MMIO. Other SPI controllers call that mode
linear addressing mode.
For this purpose, we are adding below each crontoller an array of
structs gathering for each SPI flash module, a segment rank, a
MemoryRegion to handle the memory accesses and the associated SPI
slave device, which should be a m25p80.
Only the User mode is supported for now but we are preparing ground
for the Command mode. The framework is sufficient to support Linux.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-8-git-send-email-clg@kaod.org
[PMM: Use g_new0() rather than g_malloc0()]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed AST2400 soc includes a static memory controller for the BMC
which supports NOR, NAND and SPI flash memory modules. This controller
has two modes : the SMC for the legacy interface which supports only
one module and the FMC for the new interface which supports up to five
modules. The AST2400 also includes a SPI only controller used for the
host firmware, commonly called BIOS on Intel. It can be used in three
mode : a SPI master, SPI slave and SPI pass-through
Below is the initial framework for the SMC controller (FMC mode only)
and the SPI controller: the sysbus object, MMIO for registers
configuration and controls. Each controller has a SPI bus and a
configurable number of CS lines for SPI flash slaves.
The differences between the controllers are small, so they are
abstracted using indirections on the register numbers.
Only SPI flash modules are supported.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-7-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added one missing error_propagate]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This allows specifying the property via -drive if=none and creating
the flash device with -device.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-6-git-send-email-clg@kaod.org
[clg: added an extra fix for sabrelite_init()
keeping the test on flash_dev did not seem necessary. ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The maximum amount of storage that can be addressed by the m25p80 command
set is 4 GiB. However, cur_addr is currently a 64-bit integer. To avoid
further problems related to sign extension of signed 32-bit integer
expressions, change cur_addr to a 32 bit integer. Preserve migration
format by adding a dummy 4-byte field in place of the (big-endian)
high four bytes in the formerly 64-bit cur_addr field.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-5-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
s->cur_addr can be made to point outside s->storage, either by
writing a value >= 128 to s->ear (because s->ear * MAX_3BYTES_SIZE
is a signed integer and sign-extends into the 64-bit cur_addr),
or just by writing an address beyond the size of the flash being
emulated. Avoid the sign extension to make the code cleaner, and
on top of that mask s->cur_addr to s->size.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-4-git-send-email-clg@kaod.org
Reviewed by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When doing a read-modify-write cycle, QEMU uses the iovec after returning
from blk_aio_pwritev. m25p80 puts the iovec on the stack of blk_aio_pwritev's
caller, which causes trouble in this case. This has been a problem
since commit 243e6f6 ("m25p80: Switch to byte-based block access",
2016-05-12) started doing writes at a smaller granularity than 512 bytes.
In principle however it could have broken before when using -drive
if=mtd,cache=none on a disk with 4K native sectors.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This enables qemu to handle late inits and report errors. All the SSI
slave routine names were changed accordingly. Code was modified to
handle errors when possible (m25p80 and ssi-sd)
Tested with the m25p80 slave object.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-2-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a minimal model for the devcfg device which is part of Zynq.
This model supports DMA capabilities and interrupt generation.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 83df49d8fa2d203a421ca71620809e4b04754e65.1467053537.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a helper that will scan a static RegisterAccessInfo Array
and populate a container MemoryRegion with registers as defined.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 347b810b2799e413c98d5bbeca97bcb1557946c3.1467053537.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QOMify registers as a child of TYPE_DEVICE. This allows registers to
define GPIOs.
Define an init helper that will do QOM initialisation.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: KONRAD Frederic <fred.konrad@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 2545f71db26bf5586ca0c08a3e3cf1b217450552.1467053537.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add memory io handlers that glue the register API to the memory API.
Just translation functions at this stage. Although it does allow for
devices to be created without all-in-one mmio r/w handlers.
This patch also adds the RegisterInfoArray struct, which allows all of
the individual RegisterInfo structs to be grouped into a single memory
region.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: f7704d8ac6ac0f469ed35401f8151a38bd01468b.1467053537.git.alistair.francis@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This API provides some encapsulation of registers and factors out some
common functionality to common code. Bits of device state (usually MMIO
registers) often have all sorts of access restrictions and semantics
associated with them. This API allows you to define what those
restrictions are on a bit-by-bit basis.
Helper functions are then used to access the register which observe the
semantics defined by the RegisterAccessInfo struct.
Some features:
Bits can be marked as read_only (ro field)
Bits can be marked as write-1-clear (w1c field)
Bits can be marked as reserved (rsvd field)
Reset values can be defined (reset)
Bits can be marked clear on read (cor)
Pre and post action callbacks can be added to read and write ops
Verbose debugging info can be enabled/disabled
Useful for defining device register spaces in a data driven way. Cuts
down on a lot of the verbosity and repetition in the switch-case blocks
in the standard foo_mmio_read/write functions.
Also useful for automated generation of device models from hardware
design sources.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 40d62c7e1bf6e63bb4193ec46b15092a7d981e59.1467053537.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since QEMU performs cacheable accesses to guest memory when doing DMA
as part of the implementation of emulated PCI devices, guest drivers
should use cacheable accesses as well when running under KVM. Since this
essentially means that emulated PCI devices are DMA coherent, set the
'dma-coherent' DT property on the PCIe host controller DT node.
This brings the DT description into line with the ACPI description,
which already marks the PCI bridge as cache coherent (see commit
bc64b96c98).
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 1467134090-5099-1-git-send-email-ard.biesheuvel@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Starting QEMU with -S results in current_cpu containing its initial
value of NULL. It is however possible to connect to such QEMU instance
and query various CPU registers, one example being CPUID, and doing that
results in QEMU segfaulting.
Using qemu_get_cpu(0) seem reasonable enough given that ARMv7M
architecture is a single core architecture.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The imx boards were all incorrectly creating ROMs using
memory_region_init_rom_device() with a NULL ops pointer. This
will cause QEMU to abort if the guest tries to write to the
ROM. Switch to the new memory_region_init_rom() instead.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1467122287-24974-3-git-send-email-peter.maydell@linaro.org
This reverts commit 1f8828ef57.
Cc: qemu-stable@nongnu.org
Reported-by: Robin Geuze <robing@transip.nl>
Tested-by: Robin Geuze <robing@transip.nl>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
virtio migrates the low 32 feature bits twice, the first copy is there
for compatibility but ever since
019a3edbb2: ("virtio: make features 64bit
wide") it's ignored on load. This is wrong since virtio_net_load tests
self announcement and guest offloads before the second copy including
high feature bits is loaded. This means that self announcement, control
vq and guest offloads are all broken after migration.
Fix it up by loading low feature bits: somewhat ugly since high and low
bits become out of sync temporarily, but seems unavoidable for
compatibility. The right thing to do for new features is probably to
test the host features, anyway.
Fixes: 019a3edbb2
("virtio: make features 64bit wide")
Cc: qemu-stable@nongnu.org
Reported-by: Robin Geuze <robing@transip.nl>
Tested-by: Robin Geuze <robing@transip.nl>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The host notifier rework tried both to unify host notifiers across
transports and plug a possible hole during host notifier
re-assignment. Unfortunately, this meant a change in semantics that
breaks vhost and iSCSI+dataplane.
As the minimal fix, keep the common host notifier code but revert
to the old semantics so that we have time to figure out the proper
fix.
Fixes: 6798e245a3 ("virtio-bus: common ioeventfd infrastructure")
Reported-by: Peter Lieven <pl@kamp.de>
Reported-by: Jason Wang <jasowang@redhat.com>
Reported-by: Marc-André Lureau <marcandre.lureau@gmail.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Tested-by: Jason Wang <jasowang@redhat.com>
Tested-by: Peter Lieven <pl@kamp.de>
PcPciInfo has two (ill-named) members: Range w32 is the PCI hole, and
w64 is the PCI64 hole.
Three users:
* I440FXState and MCHPCIState have a member PcPciInfo pci_info, but
only pci_info.w32 is actually used. This is confusing. Replace by
Range pci_hole.
* acpi_build() uses auto PcPciInfo pci_info to forward both PCI holes
from acpi_get_pci_info() to build_dsdt(). Replace by two variables
Range pci_hole, pci_hole64. Rename acpi_get_pci_info() to
acpi_get_pci_holes().
PcPciInfo is now unused; drop it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Range pci_info.w32 records the location of the PCI hole.
It's initialized to empty when QOM zeroes I440FXState. That's a fine
value for a still unknown PCI hole.
i440fx_init() sets pci_info.w32.begin = below_4g_mem_size. Changes
the PCI hole from empty to [below_4g_mem_size, UINT64_MAX]. That's a
bogus value.
i440fx_pcihost_initfn() sets pci_info.end = IO_APIC_DEFAULT_ADDRESS.
Since i440fx_init() ran already, this changes the PCI hole to
[below_4g_mem_size, IO_APIC_DEFAULT_ADDRESS-1]. That's the correct
value.
Setting the bounds of the PCI hole in two separate places is
confusing, and begs the question whether the bogus intermediate value
could be used by something, or what would happen if we somehow managed
to realize an i440FX device without having run the board init function
i440fx_init() first.
Avoid the confusion by setting the (constant) upper bound along with
the lower bound in i440fx_init().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Since iommu devices can be created with '-device' there is
no need to keep iommu as machine and mch property.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use the standard '-device intel-iommu' to create the IOMMU device.
The legacy '-machine,iommu=on' can still be used.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Allow adding sysbus devices with -device on Q35.
At first Q35 will support only intel-iommu to be added this way,
however the command line will support all sysbus devices.
Mark with 'cannot_instantiate_with_device_add_yet' the ones
causing immediate problems (e.g. crashes).
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Skip bus_master_enable region creation on PCI device init
in order to be sure the IOMMU device (if present) would
be created in advance. Add this memory region at machine_done time.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Mac99's PCI root bus is not part of a host bridge,
realize it manually.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit "8156d48 pc: allow raising low memory via max-ram-below-4g
option" causes a regression on xen, because it uses a different
memory split.
This patch initializes max-ram-below-4g to zero and leaves the
initialization to the memory initialization functions. That way
they can pick different default values (max-ram-below-4g is zero
still) or use the user supplied value (max-ram-below-4g is non-zero).
Also skip the whole ram split calculation on Xen. xen_ram_init()
does its own split calculation anyway so it is superfluous, also
this way xen_ram_init can actually see whenever max-ram-below-4g
is zero or not.
Reported-by: Anthony PERARD <anthony.perard@citrix.com>
Tested-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAld2ZGoACgkQAvw66wEB28LbNQCfbKhlgcwRvD/F1B5IFQErRkLf
rBsAnR5QQhl8eJK+Dfdiy4H/mjKuXHyN
=6o/q
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/gkurz/tags/for-upstream' into staging
Only trivial fixes.
# gpg: Signature made Fri 01 Jul 2016 13:39:06 BST
# gpg: using DSA key 0x02FC3AEB0101DBC2
# gpg: Good signature from "Greg Kurz <gkurz@fr.ibm.com>"
# gpg: aka "Greg Kurz <groug@free.fr>"
# gpg: aka "Greg Kurz <gkurz@linux.vnet.ibm.com>"
# gpg: aka "Gregory Kurz (Groug) <groug@free.fr>"
# gpg: aka "Gregory Kurz (Cimai Technology) <gkurz@cimai.com>"
# gpg: aka "Gregory Kurz (Meiosys Technology) <gkurz@meiosys.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 2BD4 3B44 535E C0A7 9894 DBA2 02FC 3AEB 0101 DBC2
* remotes/gkurz/tags/for-upstream:
9p: synth: drop v9fs_ prefix
9p: don't include <sys/uio.h>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Here's the current ppc patch queue. This is a fairly large batch,
containing:
* A number of further preliminary patches towards full hypervisor
mode emulation
* Some further fixes / cleanups for the recently merged device_add
based CPU hotplug
* Preliminary patches towards supporting a native (rather than
paravirtualized) XICS device. This will be needed to emulate a
physical Power machine, including hypervisor capabilities
* Assorted bug fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KhVy
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.7-20160701' into staging
ppc patch queue 2016-07-01
Here's the current ppc patch queue. This is a fairly large batch,
containing:
* A number of further preliminary patches towards full hypervisor
mode emulation
* Some further fixes / cleanups for the recently merged device_add
based CPU hotplug
* Preliminary patches towards supporting a native (rather than
paravirtualized) XICS device. This will be needed to emulate a
physical Power machine, including hypervisor capabilities
* Assorted bug fixes
# gpg: Signature made Fri 01 Jul 2016 06:56:35 BST
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.7-20160701: (23 commits)
qmp: fix spapr example of query-hotpluggable-cpus
spapr: drop duplicate variable in spapr_core_release()
spapr: do proper error propagation in spapr_cpu_core_realize_child()
spapr: drop reference on child object during core realization
spapr: Restore support for 970MP and POWER8NVL CPU cores
target-ppc: gen_pause for instructions: yield, mdoio, mdoom, miso
ppc/xics: Replace "icp" with "xics" in most places
ppc/xics: Implement H_IPOLL using an accessor
ppc/xics: Move SPAPR specific code to a separate file
ppc/xics: Rename existing xics to xics_spapr
ppc: Fix 64K pages support in full emulation
target-ppc: Eliminate redundant and incorrect function booke206_page_size_to_tlb
spapr: Restore support for older PowerPC CPU cores
spapr: fix write-past-end-of-array error in cpu core device init code
hw/ppc/spapr: Add some missing hcall function set strings
ppc: Print HSRR0/HSRR1 in "info registers"
ppc: LPCR is a HV resource
ppc: Initial HDEC support
ppc: Enforce setting MSR:EE,IR and DR when MSR:PR is set
ppc: Fix conditions for delivering external interrupts to a guest
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This patch changes spapr_cpu_core_realize_child() to have a local error
pointer and use error_propagate() as it is supposed to be done.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When a core is being realized, we create a child object for each thread
of the core.
The child is first initialized with object_initialize() which sets its ref
count to 1, and then added to the core with object_property_add_child()
which bumps the ref count to 2.
When the core gets released, object_unparent() decreases the ref count to 1,
and we g_free() the object: we hence loose the reference on an unfinalized
object. This is likely to cause random crashes.
Let's drop the extra reference as soon as we don't need it, after the
thread is added to the core.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduction of core based CPU hotplug for PowerPC sPAPR didn't
add support for 970MP and POWER8NVL based core types. Add support for
the same.
While we are here, add support for explicit specification of POWER5+_v2.1
core type.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The "ICP" is a different object than the "XICS". For historical reasons,
we have a number of places where we name a variable "icp" while it contains
a XICSState pointer. There *is* an ICPState structure too so this makes
the code really confusing.
This is a mechanical replacement of all those instances to use the name
"xics" instead. There should be no functional change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[spapr_cpu_init has been moved to spapr_cpu_core.c, change there]
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
None of the other presenter functions directly mucks with the
internal state, so don't do it there either.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Leave the core ICP/ICS logic in xics.c and move the top level
class wrapper, hypercall and RTAS handlers to xics_spapr.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[add cpu.h in xics_spapr.c, move set_nr_irqs and set_nr_servers to
xics_spapr.c]
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The common class doesn't change, the KVM one is sPAPR specific. Rename
variables and functions to xics_spapr.
Retain the type name as "xics" to preserve migration for existing sPAPR
guests.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Eliminate redundant and incorrect booke206_page_size_to_tlb function
from ppce500_spin.c in preference to previously existing but newly
exported definition from e500.c
Defect analysis:
The booke206_page_size_to_tlb function in e500.c was updated in commit
2bd9543 "ppc: booke206: use MAV=2.0 TSIZE definition, fix 4G pages" to
reflect a change in the definition of MAS1_TSIZE_SHIFT from 8
(corresponding to a min TLB page size of 4kb) to a value of 7 (TLB
page size 2k). The booke206_page_size_to_tlb() function defined in
ppce500_spin.c was never updated to reflect the change in
MAS1_TSIZE_SHIFT.
In http://lists.nongnu.org/archive/html/qemu-ppc/2016-06/msg00533.html,
Scott Wood suggested this "root cause" explanation:
SW> The patch that changed MAS1_TSIZE_SHIFT from 8 to 7 was around the
SW> same time as the patch that added this code, which is probably why
SW> adjusting it got missed. Commit 2bd9543cd3 did update the
SW> equivalent code in ppce500_mpc8544ds.c, which now resides in
SW> hw/ppc/e500.c and has been changed to not assume a power-of-2
SW> size. The ppce500_spin version should be eliminated.
Signed-off-by: Aaron Larson <alarson@ddci.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduction of core based CPU hotplug for PowerPC sPAPR didn't
add support for 970 and POWER5+ based core types. Add support for
the same.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This fixes a potential QEMU crash introduced by commit 3b54254966.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add "hcall-sprg0" (for H_SET_SPRG0), "hcall-copy" (for H_PAGE_INIT)
and "hcall-debug" (for H_LOGICAL_CI_LOAD/STORE) to the property
"ibm,hypertas-functions" to indicate that we support these hypercalls.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The current behaviour isn't completely right, as for the DEC, we
don't properly re-arm when wrapping around, but I will fix this
in a separate patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[clg: fixed checkpatch.pl errors ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We don't currently support the MemoryRegionIOMMUOps notifier, so throw
an error should a device require it.
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: Peter Xu <peterx@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The IOMMU driver may change behavior depending on whether a notifier
client is present. In the case of POWER, this represents a change in
the visibility of the IOTLB, for other drivers such as intel-iommu and
future AMD-Vi emulation, notifier support is not yet enabled and this
provides the opportunity to flag that incompatibility.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: Peter Xu <peterx@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
[new log & extracted from [PATCH qemu v17 12/12] spapr_iommu, vfio, memory: Notify IOMMU about starting/stopping listening]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The kernel currently exposes the SR-IOV capability as read-only
through vfio-pci. This is sufficient to protect the host kernel, but
has the potential to confuse guests without further virtualization.
In particular, OVMF tries to size the VF BARs and comes up with absurd
results, ending with an assert. There's not much point in adding
virtualization to a read-only capability, so we simply hide it for
now. If the kernel ever enables SR-IOV virtualization, we should
easily be able to test it through VF BAR sizing or explicit flags.
Testing whether we should parse extended capabilities is also pulled
into the function to keep these assumptions in one place.
Tested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
For vfio pcie device, we could expose the extended capability on
PCIE bus. due to add a new pcie capability at the tail of the chain,
in order to avoid config space overwritten, we introduce a copy config
for parsing extended caps. and rebuild the pcie extended config space.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Commit 2d82f8a3cd ("vfio/pci: Convert all MemoryRegion to dynamic
alloc and consistent functions") converted VFIOPCIDevice.vga to be
dynamically allocted, negating the need for VFIOPCIDevice.has_vga.
Unfortunately not all of the has_vga users were converted, nor was
the field removed from the structure. Correct these oversights.
Reported-by: Peter Maloney <peter.maloney@brockmann-consult.de>
Tested-by: Peter Maloney <peter.maloney@brockmann-consult.de>
Fixes: 2d82f8a3cd ("vfio/pci: Convert all MemoryRegion to dynamic alloc and consistent functions")
Fixes: https://bugs.launchpad.net/qemu/+bug/1591628
Cc: qemu-stable@nongnu.org
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The link property that was added to the pcspk device has the wrong type:
it is only correct for TCG and for KVM's userspace or split irqchip
options. The default KVM option (fully in-kernel irqchip) breaks
because it uses a PIT whose type is a sibling of TYPE_I8254.
Fixes: 873b4d3f05
Tested-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1467298657-6588-1-git-send-email-pbonzini@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Otherwise, a serial port can get stuck if it is migrated while flow control
is in effect.
Tested-by: Bret Ketchum <bcketchum@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Otherwise, this can cause serial_xmit to be entered with LSR.TEMT=0,
which is invalid and causes an assertion failure.
Reported-by: Bret Ketchum <bcketchum@gmail.com>
Tested-by: Bret Ketchum <bcketchum@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
g_source_attach can return any value between 1 and UINT_MAX if you let
QEMU run long enough. However, qemu_chr_fe_add_watch can also return
a negative errno value when the device is disconnected or does not
support chr_add_watch. Change it to return zero to avoid overloading
these values.
Fix the cadence_uart which asserts in this case (easily obtained with
"-serial pty").
Tested-by: Bret Ketchum <bcketchum@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
serial_xmit starts transmission of whatever is in the transmitter
register, THR or FIFO; serial_watch_cb is a wrapper around it and is
only used as a qemu_chr_fe_add_watch callback.
Tested-by: Bret Ketchum <bcketchum@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move common code outside the if, and reset tsr_retry even in loopback mode.
Right now it cannot become non-zero, but it will be possible as soon as
we start respecting the baud rate.
Tested-by: Bret Ketchum <bcketchum@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It can never become negative; reflect this in the type of the field
and simplify the conditions.
Tested-by: Bret Ketchum <bcketchum@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In function pci_assign_dev_load_option_rom, For those pci devices don't
have 'rom' file under sysfs or if loading ROM from external file, The
function returns NULL, and won't set the passed 'size' variable.
In these 2 cases, qemu still reports "Invalid ROM" error message, Users
may be confused by it.
Signed-off-by: Lin Ma <lma@suse.com>
Message-Id: <1466010327-22368-1-git-send-email-lma@suse.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 926cde5 ("scsi: esp: make cmdbuf big enough for maximum CDB size",
2016-06-16) changed the size of a migrated field. Split it in two
parts, and only migrate the second part in a new vmstate version.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The MC146818 RTC device has output IRQ line. Currently the corresponding field
is only accessible through direct access. Such access violates Qemu model.
The patch makes the field accessible through GPIO. It also updates the setting
of the IRQ during initialization.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently a direct access to the device structure field is used to connect ISA
device IRQ to the bus. GPIO access should be used instead if possible.
The patch adds wrapper isa_connect_gpio_out. The function connects specified
output GPIO to specified ISA IRQ.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The isa_bus_irqs function initializes ISA bus IRQ array pointer with specified
value.
Previously the ICH9 LPC bridge model did not have its own IRQs but
only IRQ pointer cache. And same GSI were used for ISA bus and other sources
behind the bridge (PCI, SCI). Hence, the pc_q35_init was only possible place to
setup both ISA bus IRQs and the bridge IRQ cache.
As a result, the call of isa_bus_irqs was made from pc_q35_init.
Now the ICH9 LPC bridge has its own output IRQs which are connected to GSI. The
output IRQs are already used to route IRQs from PCI and SCI.
The patch makes the ICH9 LPC bridge output IRQs to used for ISA bus too.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The ICH9 LPC bridge has 24 output IRQs connected to GSI. Currently the IRQs are
referenced by pointers. The pointers are initialized at startup by direct access
to the structure fields. This violates Qemu device model.
The patch makes the IRQs handling to use GPIO model.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
ich9->pic and ich9->ioapic differ for the first 16 GSIs (because
ich9->pic is wired to 8259+IOAPIC but ich9->ioapic is wired to
IOAPIC only). However, ich9->ioapic is never used for the first
16 GSIs, so the two vectors can be merged.
Reviewed-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make ich9_lpc_update_pic take care only of GSIs 0-15, and
ich9_lpc_update_apic take care only of GSIs 16-23. Assert
that they are called with the correct GSI indices.
Reviewed-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
An asserted pirq can be disabled and the corresponding GSIs
should then go down to 0. However, because of the conditional in
ich9_lpc_update_by_pirq, the legacy 8259 pin could remain stuck to 1.
Reviewed-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
ICH9 SMB bridge can be created using qdev API despite existence of helper
function. The type name is needed for such creation. Using a preprocessor
alias instead the string type name itself is preferable.
The patch makes the alias accessible through the header.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The port92 device has outgouing IRQ line A20. Currently the IRQ is referenced
by a pointer which normally is set during machine initialization. The
pointer is never changed at runtime. Hence, common GPIO model can be applied
to A20 IRQ line. Note that checking for IRQ to be connected as in
previous version of code is not required qemu_set_irq will do it.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The i8042 device has outgouing IRQ line A20. Currently the IRQ is referenced
by a pointer which normally is set during machine initialization. The pointer
is never changed at runtime. So common GPIO model can be applied to A20 IRQ
line. Note that checking for IRQ to be connected as in previous version
of code is not required because qemu_set_irq will do it.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, Q35 instance is configured using direct access to structure fields.
The patch uses property interface to set the fields.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
During creation of Q35 instance several parameters are set using direct access.
It violates Qemu device model. Correctly, the parameters should be handled as
object properties.
The patch adds four link type properties for fields:
mch.ram_memory
mch.pci_address_space
mch.system_memory
mch.address_space_io
And, it adds two size type properties for fields:
mch.below_4g_mem_size
mch.above_4g_mem_size
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qdev API can be used to create CFI pflash devices despite existance of helper
functions. The type name is needed in course of such creation. Using the
preprocessor alias instead of the string literal itself is preferable.
The patch makes the aliases accessible through the header.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently vmport device is identified by the string literal. Using a
preprocessor alias instead is preferable.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The speaker device needs pointer to ISA PIT device to operate. But according to
qdev-properties.h, properties of pointer type should be avoided. It seems a
link type property is a good substitution.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use ldl_le_p() and stl_le_p() instead of le32_to_cpup() and
cpu_to_le32w(); the former handle misaligned addresses and don't
need casts, and the latter are deprecated.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
Message-id: 1465575021-3774-1-git-send-email-peter.maydell@linaro.org
Multiqueue virtio-blk can be enabled as follows:
qemu -device virtio-blk-pci,num-queues=8
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466511196-12612-8-git-send-email-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Monitor ioeventfds for all virtqueues in the device's AioContext. This
is not true multiqueue because requests from all virtqueues are
processed in a single IOThread. In the future it will be possible to
use multiple IOThreads when the QEMU block layer supports multiqueue.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466511196-12612-7-git-send-email-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add a field for the virtqueue index when migrating the s->rq request
list. The new field is only needed when num_queues > 1. Existing QEMUs
are unaffected by this change and therefore virtio-blk migration stays
compatible.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466511196-12612-6-git-send-email-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Multiqueue requires that each request knows to which virtqueue it
belongs.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466511196-12612-5-git-send-email-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Let the virtio_blk_data_plane_notify() caller decide which virtqueue to
notify. This will allow the function to be used with multiqueue.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466511196-12612-4-git-send-email-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The batch notification BH needs to know which virtqueues to notify when
multiqueue is enabled. Use a bitmap to track the virtqueues with
pending notifications.
At this point there is only one virtqueue so hard-code virtqueue index
0. A later patch will switch to real virtqueue indices.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466511196-12612-3-git-send-email-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The num_queues field is always 1 for the time being. A later patch will
make it a configurable device property so that multiqueue can be
enabled.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466511196-12612-2-git-send-email-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This reverts commit 10a06fd65f.
Dataplane has used the same virtqueue code as non-dataplane since
commits e24a47c5b7 ("virtio-scsi: do not
use vring in dataplane") and 03de2f5274
("virtio-blk: do not use vring in dataplane"). It is no longer
necessary to stop dataplane in order to sync state since there is no
duplicated virtqueue state.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Message-id: 1466503331-9831-1-git-send-email-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJXce8xAAoJEO8Ells5jWIRorwH/3Q+fHmkSBlPGOna9zOs4zrB
SB6/aa9Yw2UXCZJgCIh/5Ci09/lCJGVEkX7pkYEBuTwW3PceYWPQJAWpzDlmG0ch
U1xaVNuCubmMoVfD/4BEWQR3SdJ0VGVnunhWkAB4sh/PKb7csVv9DdwIDvfD7ZsF
1hGNvybxWu3RMaX2HxQKCrp9QdGaFAfkGivQCq+NACckytEdBZJVPMc5Qc4y/4S6
HOGBMYLYwp5vhJi1sZjnwB2otyZS4yxVkPlR2EexaOpWrqpOFDLiYpPWVINWLWM+
C/NV4qZfb3kU8zaIQCKuTPPmq/N7CrC1uPen3AhhSgpxrlA+nZ8af1tOruhoHA4=
=8N5c
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Tue 28 Jun 2016 04:29:53 BST
# gpg: using RSA key 0xEF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
vmxnet3: Fix reading/writing guest memory specially when behind an IOMMU
rtl8139: save/load RxMulOk counter (again)
Change net/socket.c to use socket_*() functions
net: mipsnet: check transmit buffer size before sending
net: fix qemu_announce_self not emitting packets
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tracing configurations error out currently as follows:
/home/travis/build/pranith/qemu/hw/misc/aspeed_scu.c: In function ‘aspeed_scu_read’:
/home/travis/build/pranith/qemu/hw/misc/aspeed_scu.c:130:9: error: implicit declaration of function ‘qemu_log_mask’ [-Werror=implicit-function-declaration]
/home/travis/build/pranith/qemu/hw/misc/aspeed_scu.c:130:9: error: nested extern declaration of ‘qemu_log_mask’ [-Werror=nested-externs]
/home/travis/build/pranith/qemu/hw/misc/aspeed_scu.c:130:23: error: ‘LOG_GUEST_ERROR’ undeclared (first use in this function)
/home/travis/build/pranith/qemu/hw/misc/aspeed_scu.c:130:23: note: each undeclared identifier is reported only once for each function it appears in
/home/travis/build/pranith/qemu/hw/misc/aspeed_scu.c: In function ‘aspeed_scu_write’:
/home/travis/build/pranith/qemu/hw/misc/aspeed_scu.c:154:23: error: ‘LOG_GUEST_ERROR’ undeclared (first use in this function)
This is caused by a missing header file. Fix it.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20160627215304.821-1-bobby.prani@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When a PCI device lives behind an IOMMU, it should use 'pci_dma_*' family of
functions when any transfer from/to guest memory is required while
'cpu_physical_memory_*' family of functions completely bypass any MMU/IOMMU in
the system.
vmxnet3 in some places was using 'cpu_physical_memory_*' family of functions
which works fine with the default QEMU setup where IOMMU is not enabled but
fails miserably when IOMMU is enabled. This commit converts all such instances
in favor of 'pci_dma_*'
Cc: Dmitry Fleytman <dmitry@daynix.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: Anthony Liguori <aliguori@amazon.com>
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Acked-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Commit 9d29cdeaac (rtl8139: port
TallyCounters to vmstate) introduced in incompatibility in the v4
format as it omitted the RxOkMul counter.
There are presumably no users that were impacted by the v4 to v4'
breakage, so increase the save version to 5 and re-add the field,
keeping backward compatibility with v4'.
We can't have a field conditional on the section version in
vmstate_tally_counters since this version checked would not be the
section version (but the version defined in this structure). So, move
all the fields into the main state structure.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
When processing MIPSnet I/O port write operation, it uses a
transmit buffer tx_buffer[MAX_ETH_FRAME_SIZE=1514]. Two indices
's->tx_written' and 's->tx_count' are used to control data written
to this buffer. If the two were to be equal before writing, it'd
lead to an OOB write access beyond tx_buffer. Add check to avoid it.
Reported-by: Li Qiang <qiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
We only care about the associated backend, so blk_drain is more
appropriate here.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20160612065603.21911-1-famz@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Don't use *_to_cpup() to do byte-swapped loads; instead use
ld*_p() which correctly handle misaligned accesses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Dmitry Fleytman <dmitry@daynix.com <mailto:dmitry@daynix.com>>
Message-id: 1466097446-981-6-git-send-email-peter.maydell@linaro.org
Don't use *_to_cpup() to do byte-swapped loads; instead use
ld*_p() which correctly handle misaligned accesses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Dmitry Fleytman <dmitry@daynix.com <mailto:dmitry@daynix.com>>
Message-id: 1466097446-981-5-git-send-email-peter.maydell@linaro.org
Don't use *_to_cpup() to do byte-swapped loads; instead use
ld*_p() which correctly handle misaligned accesses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Dmitry Fleytman <dmitry@daynix.com <mailto:dmitry@daynix.com>>
Message-id: 1466097446-981-4-git-send-email-peter.maydell@linaro.org
Don't use *_to_cpup() to do byte-swapped loads; instead use
ld*_p() which correctly handle misaligned accesses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Dmitry Fleytman <dmitry@daynix.com <mailto:dmitry@daynix.com>>
Message-id: 1466097446-981-3-git-send-email-peter.maydell@linaro.org
Don't use cpu_to_*w() and *_to_cpup() to do byte-swapped loads
and stores; instead use ld*_p() and st*_p() which correctly handle
misaligned accesses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Dmitry Fleytman <dmitry@daynix.com <mailto:dmitry@daynix.com>>
Message-id: 1466097446-981-2-git-send-email-peter.maydell@linaro.org
This commit fix obvious bug in WINBOND command handling.
Datasheet states that default dummy cycles is 8 so fix it.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Message-id: 1466755631-25201-11-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Macronix: mx66u51235f and mx66u1g45g
Micron: mt25ql01g and mt25qu01g
Spansion: s25fs512s and s70fs01gs
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1466755631-25201-10-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Support for Spansion and Macronix flashes.
Additionally Numonyx(Micron) moved from default
in fast read commands family. Also moved fast read
command decoding to functions.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1466755631-25201-9-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Configuration registers for Spansion and Macronix devices.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1466755631-25201-8-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Quad and Equad modes for Spansion and Macronix flash devices.
This commit also includes modification and new command to manipulate
quad mode (status registers and dedicated commands).
This work is based on Pawel Lenkow work.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1466755631-25201-7-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Page program 4byte/quad and erase 32K sectors 4 bytes.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1466755631-25201-6-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some flash allows to stop read at any time.
Allow framework to support this.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1466755631-25201-5-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow to have more than four 16MiB regions for bigger flash devices.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1466755631-25201-4-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since it is now longer than 4. This work based on Pawel Lenkow
changes and the kernel SPI framework.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1466755631-25201-3-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instead of always reading and comparing jededc ID,
replace it by function.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Message-id: 1466755631-25201-2-git-send-email-marcin.krzeminski@nokia.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
By specifying the silicon revision we select the appropriate reset
values for the SoC.
Additionally, expose hardware strapping properties aliasing those
provided by the SCU for board-specific configuration.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1466744305-23163-3-git-send-email-andrew@aj.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SCU is a collection of chip-level control registers that manage the
various functions supported by ASPEED SoCs. Typically the bits control
interactions with clocks, external hardware or reset behaviour, and we
can largly take a hands-off approach to reads and writes.
Firmware makes heavy use of the state to determine how to boot, but the
reset values vary from SoC to SoC (eg AST2400 vs AST2500). A qdev
property is exposed so that the integrating SoC model can configure the
silicon revision, which in-turn selects the appropriate reset values.
Further qdev properties are exposed so the board model can configure the
board-dependent hardware strapping.
Almost all provided AST2400 reset values are specified by the datasheet.
The notable exception is SOC_SCRATCH1, where we mark the DRAM as
successfully initialised to avoid unnecessary dark corners in the SoC's
u-boot support.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1466744305-23163-2-git-send-email-andrew@aj.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: drop unnecessary inttypes.h include]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Cadence GEM data sheet says:
"Wrap - marks last descriptor in transmit buffer descriptor list. This
can be set for any buffer within the frame."
which seems to imply that when the wrap bit is set so is the last bit.
Previously if the wrap bit is set, but the last is not then QEMU will
enter an infinite loop.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reported-by: Li Qiang <liqiang6-s@360.cn>
Reported-by: P J P <ppandit@redhat.com>
Message-id: eb23f15c67989ea6a53609dc66568399dadf52a7.1466539342.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A guest can write zero to the DMACFG resulting in an infinite loop when
it reaches the while(bytes_to_copy) loop.
To avoid this issue enforce a minimum size for the RX buffer. Hardware
does not have this enforcement and relies on the guest to set a non-zero
value.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reported-by: Li Qiang <liqiang6-s@360.cn>
Reported-by: P J P <ppandit@redhat.com>
Message-id: 84bb1c391b833275da3f573d4972920cea34c188.1466539342.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If qemu_chr_fe_write() returns an error (represented by a negative
number) we should skip incrementing the count and initiating a
memmove().
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 667e5dc534d33338fcfc2471e5aa32fe7cbd13dc.1466546703.git.alistair.francis@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These are spotted by coverity 1356936 and 1356937.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1466387717-13740-1-git-send-email-zhaoshenglong@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
struct CPUCore uses 'id' suffix in the property name. As docs for
query-hotpluggable-cpus state that the cpu core properties should be
passed back to device_add by management in case new members are added
and thus the names for the fields should be kept in sync.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
[dwg: Removed a duplicated word in comment]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
[dwg: Adjusted for context to apply without original series]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
ppce500_spin.c uses SPR_PIR to initialize the spin table, however on
Book E processors the correct SPR is SPR_BOOKE_PIR.
Signed-off-by: Aaron Larson <alarson@ddci.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
All users have been converted to the new ioevent callbacks.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Convert to the new interface.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Convert to new interface.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use the new interface.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Have vhost and dataplane use the new api for transports that
have been converted.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce a set of ioeventfd callbacks on the virtio-bus level
that can be implemented by the individual transports. At the
virtio-bus level, do common handling for host notifiers (which
is actually most of it).
Two things of note:
- When setting the host notifier, we only switch from/to the
generic ioeventfd handler. This fixes a latent bug where we
had no ioeventfd assigned for a certain window.
- We always iterate over all possible virtio queues, even though
ccw (currently) has a lower limit. It does not really matter
here.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PCMachineState.node_cpu was used for mapping APIC ID
to numa node id as CPU entries in SRAT used to be
built on sparse APIC ID bitmap (up to apic_id_limit).
However since commit
5803fce pc: acpi: SRAT: create only valid processor lapic entries
CPU entries in SRAT aren't build using apic bitmap
but using 0..maxcpus index instead which is also used
for creating numa_info[x].node_cpu map.
So instead of doing useless intermediate conversion from
1. node by cpu index -> node by apic id
i.e. numa_info[x].node_cpu -> PCMachineState.node_cpu
2. apic id -> srat entry PMX
PCMachineState.node_cpu[apic id] -> PMX value
use numa_info[x].node_cpu map directly like ARM does and do
1. numa_info[x].node_cpu -> PMX value using index
in range 0..maxcpus
and drop not necessary PCMachineState.node_cpu and related
code.
That also removes the last (not counting legacy hotplug)
dependency of ACPI code on apic_id_limit and need to allocate
huge sparse PCMachineState.node_cpu array in case of 32-bit
APIC IDs.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For compatibility reasons PC/Q35 will start with legacy
CPU hotplug interface by default but with new CPU hotplug
AML code since 2.7 machine type. That way legacy firmware
that doesn't use QEMU generated ACPI tables will be
able to continue using legacy CPU hotplug interface.
While new machine type, with firmware supporting QEMU
provided ACPI tables, will generate new CPU hotplug AML,
which will switch to new CPU hotplug interface when
guest OS executes its _INI method on ACPI tables
loading.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it adds HW and AML parts for CPU_Device._OST method
handling to allow OSPM reports status of hot-(un)plug
operation.
And extends QMP command query-acpi-ospm-status to report
CPU's OST info along with already reported PC-DIMM devices.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it adds hw registers needed for handling CPU hot-remove and
corresponding AML methods to request and eject a CPU with
necessary hotplug callbacks in pc,piix4,ich9 code.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it adds hw registers needed for handling CPU hot-add and
corresponding AML methods to handle hot-add events on
guest side.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add madt_cpu callback to AcpiDeviceIfClass and use
it for generating LAPIC MADT entries for CPUs.
Later it will be used for generating x2APIC
entries in case of more than 255 CPUs and also
would be reused by ARM target when ACPI CPU hotplug
is introduced there.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it adds CPU objects to DSDT with _STA method
and QEMU side of CPU hotplug interface initialization
with registers sufficient to handle _STA requests,
including necessary hotplug callbacks in piix4,ich9 code.
Hot-(un)plug hw/acpi parts will be added by
corresponding follow up patches.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It will be used to select which hotplug call-back is called
and for switching from legacy mode into new one.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The current code creates a whole page mmio region for the MSI-X table
size.
However, the page containing the MSI-X table may contain other registers
not related to MSI-X. Creating an mmio region for the whole page masks
such registers and may break drivers in the guest OS.
Since maximal number of entries is known, use that instead to deduce the
table size when setting up the mmio region.
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Function 6 is used to set Namespace Label Data
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Function 5 is used to get Namespace Label Data
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Function 4 is used to get Namespace label size
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently only revision 1 is supported
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It separates the operations between root device and nvdimm devices
in order to introducing label functions support for nvdimm device
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Check arg0 which indicates UUID to see if it is valid
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Check if the input Arg3 is valid then store it into ARG3 if it is
needed
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now we pass HDLE to Qemu properly, use 0 for root device and use the
handle for nvdimm devices
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It will be used by NVDIMM ACPI
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Implement ObjectType which is used by NVDIMM _DSM method in
later patch
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce a parameter, 'label-size', which is the size of nvdimm label
data area which is reserved at the end of backend memory. It is required
at least 128k
Two callbacks, read_label_data() and write_label_data(), are used to
operate the label area
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This callback returns the MemoryRegion that is the memory of dimm should
be kept during live migration
nvdimm device is different with pc-dimm as its memory includes not only
the MemoryRegion directly mapping to guest's address space but also the
memory used as label data
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use the ACPI table construction tools to create an ACPI entry
for IPMI. This adds a function called build_acpi_ipmi_devices
to add an DSDT entry for IPMI if IPMI is compiled in and an
IPMI device exists. It also adds a dummy function if IPMI
is not compiled in.
This conforms to section "C3-2 Locating IPMI System Interfaces in
ACPI Name Space" in the IPMI 2.0 specification.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add an IPMI table entry to the SMBIOS.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This will let things in other files (like IPMI) build SMBIOS tables.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently outstanding patches for spapr, target-ppc and related
devices. This batch has:
* Significant new progress towards full support for hypervisor
mode
* Assorted bugfixes
* Some preliminary patches towards dynamic DMA window support
The last involves a change to memory.c, which Paolo has said I can
take through this tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Da1O
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.7-20160623' into staging
ppc patch queue for 2016-06-23
Currently outstanding patches for spapr, target-ppc and related
devices. This batch has:
* Significant new progress towards full support for hypervisor
mode
* Assorted bugfixes
* Some preliminary patches towards dynamic DMA window support
The last involves a change to memory.c, which Paolo has said I can
take through this tree.
# gpg: Signature made Thu 23 Jun 2016 06:47:53 BST
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.7-20160623:
ppc: Disable huge page support if it is not available for main RAM
ppc: Add P7/P8 Power Management instructions
ppc: Move exception generation code out of line
ppc: Turn a bunch of booleans from int to bool
ppc: Add real mode CI load/store instructions for P7 and P8
ppc: Rework generation of priv and inval interrupts
ppc: Fix generation if ISI/DSI vs. HV mode
ppc: Fix POWER7 and POWER8 exception definitions
ppc: fix exception model for HV mode
ppc: define a default LPCR value
ppc: Fix rfi/rfid/hrfi/... emulation
memory: Add reporting of supported page sizes
ppc: Improve emulation of THRM registers
target-ppc: Fix rlwimi, rlwinm, rlwnm again
ppc64: disable gen_pause() for linux-user mode
tests: Use '+=' to add additional tests, not '='
powerpc/mm: Update the WIMG check during H_ENTER
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make attached property settable and turns off auto-attach in case the
device was hotplugged. Hotplugging works simliar to usb-bot now.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1465984019-28963-6-git-send-email-kraxel@redhat.com
This patch marks usb-bot as hot-pluggable device, makes attached
property settable and turns off auto-attach in case the device
was hotplugged.
Hot-plugging a usb-bot device with one or more scsi devices can be
done this way now:
(1) device-add usb-bot,id=foo
(2) device-add scsi-{hd,cd},bus=foo.0,lun=0
(2b) optionally add more devices (luns 0 ... 15).
(3) qom-set foo.attached = true
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1465984019-28963-5-git-send-email-kraxel@redhat.com
USB devices in attached state are visible to the guest. This patch adds
a QOM property for this. Write access is opt-in per device. Some
devices manage attached state automatically (usb-host, usb-serial,
usb-redir), so we can't enable write access universally but have to do
it on a case by case base. So far, no device opts in.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1465984019-28963-4-git-send-email-kraxel@redhat.com
[ minor codestyle fix ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Commit 9432e53a5b added xen_sysdev as a
system device to serve as an anchor for removable virtual buses. This
introduced a build failure for non-x86 builds with CONFIG_XEN_BACKEND
set, as xen_sysdev was defined in a x86 specific file while being
consumed in an architecture independent source.
Move the xen_sysdev definition and initialization to xen_backend.c to
avoid the build failure.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
In case the word size of the domU and qemu running the qdisk backend
differ BLKIF_OP_DISCARD will not work reliably, as the request
structure in the ring have different layouts for different word size.
Correct this by copying the request structure in case of different
word size element by element in the BLKIF_OP_DISCARD case, too.
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Every IOMMU has some granularity which MemoryRegionIOMMUOps::translate
uses when translating, however this information is not available outside
the translate context for various checks.
This adds a get_min_page_size callback to MemoryRegionIOMMUOps and
a wrapper for it so IOMMU users (such as VFIO) can know the minimum
actual page size supported by an IOMMU.
As IOMMU MR represents a guest IOMMU, this uses TARGET_PAGE_SIZE
as fallback.
This removes vfio_container_granularity() and uses new helper in
memory_region_iommu_replay() when replaying IOMMU mappings on added
IOMMU memory region.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
[dwg: Removed an unnecessary calculation]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Support for 0 value for memeory coherence is optional and with ppc64
we can always enable memory coherence. Linux kernel did that during
the development of 4.7 kernel. But that resulted in failure in Qemu
in H_ENTER hcall due to below check. The mentioned change was reverted
in the kernel and kernel right now enable memory coherence only if
cache inhibited is not set. Nevertheless update qemu WIMG flag check
to cover the case where we enable memory coherence along with cache
inhibited flag.
In order to handle older and newer kernel version consider both Cache
inhibitted and (cache inhibitted | memory conference) as valid values
for wimg flags.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Version: GnuPG v1
iQEcBAABAgAGBQJXaFInAAoJEJykq7OBq3PI6VsH/0Sfgbdo1RksYuQwb/y92sCW
EN+lxUZ+OLfgrc8PYgNZwfSM3rsfYhznL0MAXOeEe7Ahabi07w7DhGR8WvwfAOlI
G96FRuvrIPfv5u6U6fwS4CvG3TIHVLxfHKCsTpPUmH8U5CNx/x/tpjNiWN1dj6t+
sXybSjYHfZfiZy2tI9MFIFWCdxnF/pl0QAPhbRqc8Y/RQTDrPKRjLpz+nitN/u96
5TS7KlELyQuP91YMmLceYSmIkHbxW703h+iE2n4hov0uZCP8Jil+2Jsd3ziQSRlL
j6LqexQ2ViBGdDSfiZGYES2VPlsHOCwb4G+IgWBStfZg1ppaXENvcDzPrgrB+L4=
=eUnF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/tracing-pull-request' into staging
# gpg: Signature made Mon 20 Jun 2016 21:29:27 BST
# gpg: using RSA key 0x9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha/tags/tracing-pull-request: (42 commits)
trace: split out trace events for linux-user/ directory
trace: split out trace events for qom/ directory
trace: split out trace events for target-ppc/ directory
trace: split out trace events for target-s390x/ directory
trace: split out trace events for target-sparc/ directory
trace: split out trace events for net/ directory
trace: split out trace events for audio/ directory
trace: split out trace events for ui/ directory
trace: split out trace events for hw/alpha/ directory
trace: split out trace events for hw/arm/ directory
trace: split out trace events for hw/acpi/ directory
trace: split out trace events for hw/vfio/ directory
trace: split out trace events for hw/s390x/ directory
trace: split out trace events for hw/pci/ directory
trace: split out trace events for hw/ppc/ directory
trace: split out trace events for hw/9pfs/ directory
trace: split out trace events for hw/i386/ directory
trace: split out trace events for hw/isa/ directory
trace: split out trace events for hw/sd/ directory
trace: split out trace events for hw/sparc/ directory
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move all trace-events for files in the hw/alpha/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-33-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/arm/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-32-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/acpi/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-31-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/vfio/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-30-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/s390x/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-id: 1466066426-16657-29-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/pci/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-28-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/ppc/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 1466066426-16657-27-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/9pfs/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-26-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/i386/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-25-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/isa/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-24-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/sd/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-23-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/sparc/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-22-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/dma/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-21-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/timer/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-20-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/input/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-19-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/display/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-18-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/nvram/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-17-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/scsi/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-16-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/usb/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-15-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/misc/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-14-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/audio/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-13-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/virtio/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-12-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/net/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-11-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/intc/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-10-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/char/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-9-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/block/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-8-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The old milkymist.org domain just forwards to mm-labs.hk nowadays. I've
created a mirror of the documents.
Signed-off-by: Michael Walle <michael@walle.cc>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Acked-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michael Walle <michael@walle.cc>
* Drop the old SysBus init function and use instance_init
* Move graphic_console_init into realize stage
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michael Walle <michael@walle.cc>
* Drop the old SysBus init function and use instance_init
* Move tmu2_glx_init into realize stage
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michael Walle <michael@walle.cc>
* split the old SysBus init function into an instance_init
and a Device realize function
* use DeviceClass::realize instead of SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Acked-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michael Walle <michael@walle.cc>
* split the old SysBus init function into an instance_init
and a Device realize function
* use DeviceClass::realize instead of SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Acked-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michael Walle <michael@walle.cc>
Use Coccinelle script to replace 'ret = E; return ret' with
'return E'. The script will do the substitution only when the
function return type and variable type are the same.
Manual fixups:
* audio/audio.c: coding style of "read (...)" and "write (...)"
* block/qcow2-cluster.c: wrap line to make it shorter
* block/qcow2-refcount.c: change indentation of wrapped line
* target-tricore/op_helper.c: fix coding style of
"remainder|quotient"
* target-mips/dsp_helper.c: reverted changes because I don't
want to argue about checkpatch.pl
* ui/qemu-pixman.c: fix line indentation
* block/rbd.c: restore blank line between declarations and
statements
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1465855078-19435-4-git-send-email-ehabkost@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Unused Coccinelle rule name dropped along with a redundant comment;
whitespace touched up in block/qcow2-cluster.c; stale commit message
paragraph deleted]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
This patch simplifies code that uses a local_err variable just to
immediately use it for an error_propagate() call.
Coccinelle patch used to perform the changes added to
scripts/coccinelle/remove_local_err.cocci.
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1465855078-19435-3-git-send-email-ehabkost@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Blank line in s390-virtio-ccw.c restored]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
error_propagate() already ignores local_err==NULL, so there's no
need to check it before calling.
Coccinelle patch used to perform the changes added to
scripts/coccinelle/error_propagate_null.cocci.
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1465855078-19435-2-git-send-email-ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
