BM_STATUS_INT is automatically set during ide_set_irq(), there's no reason to
set it manually in addition.
There is even one case where the interrupt status bit was set, but no IRQ was
raised. This is when the PRD table was reached but there is more data to
transfer. The correct behaviour for this case is not to set BM_STATUS_INT.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
AHCI provides two ways of reading/writing data:
1) NCQ
2) ATA commands with the LBA in the command FIS
In the second code path, we didn't handle any LBAs that were bigger than
16 bits, so whenever a guest that used high LBA numbers wanted to access
data, the LBA got truncated down to 16 bits, giving the guest garbage.
This patch adds support for LBAs higher than 16 bits. I've tested that it
works just fine with SeaBIOS and Linux guests. This patch also unbreaks
the often reported grub errors people have seen with AHCI.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
DriveInfo is closely tied to -drive, and like -drive, it mixes
information about host and guest part of the block device. Unlike
DriveInfo, BlockDriverState should be about the host part only.
One of the remaining guest bits there is the "type hint". -drive
option media sets it, and qdevs "ide-drive", "scsi-disk" and non-qdev
IF_XEN devices check it to pick HD vs. CD.
Communicate -drive option media via new DriveInfo member media_cd
instead.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
An "ide-drive" is either a hard disk or a CD-ROM, depending on the
associated BlockDriverState's type hint. Unclean; disk vs. CD belongs
to the guest part, not the host part.
Have separate qdevs "ide-hd" and "ide-cd" to model disk vs. CD in
the guest part.
Keep ide-drive for backward compatibility.
"ide-disk" would perhaps be a nicer name than "ide-hd", but there's
already "scsi-disk", which is like "ide-drive", and will be likewise
split in the next commit. {ide,scsi}-{hd,cd} is the best consistent
set of names I could find within the backward compatibility
straightjacket.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
If ahci_dma_set_inactive is called a while there is still a pending BH
from a previous run, we will crash on the second run of
ahci_check_cmd_bh as it overwrites AHCIDevice::check_bh. Avoid this
broken and redundant duplicate registration.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
These printfs aren't really debug messages, but clearly indicate a bug if they
ever become effective. Noone uses DEBUG_IDE, let's re-enable the check
unconditionally and make it an assertion instead of printfs in the device
emulation.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Fix regression of 667bb59: ahci_init initializes ahci.mem, so we have to
move bar registration after it.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The commit 667bb59d23
uses d->ahci.mem before it is initialized by
ahci_init(). Fix this by calling ahci_init() first thing
so that it's safe to use all fields in the ahci state struct.
Reported-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Tested-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
msi_init may fail, so we need to check on uninit if the cap was
actually installed. This also avoids that the users need to check.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
After the re-org of the atapi code, it might not be intuitive for a
reader of the code to understand why we're inserting a 'media not
present' state between cd changes.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some commands are supposed to report a Not Ready Condition (i.e. they require
a medium to be present in order to execute successfully). Instead of
duplicating the check in each command implementation, let's add a flag and
check it before calling the command.
This patch only converts existing checks, it does not introduce new checks for
any of the other commands that can/should report a Not Ready Condition.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The disk size can only change when the medium is changed, and the change
callback takes care of updating s->nb_sectors in this case.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In preparation for a table of function pointers, factor each command out from
ide_atapi_cmd() into its own function.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Besides moving code, this patch only fixes some whitespace issues in the moved
code and makes all functions in atapi.c static which can be static.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
MMC-5 Table F.1 lists errors that can be thrown for the TEST_UNIT_READY
command. Going from medium not ready to medium ready states is
communicated by throwing an error.
This adds the missing 'tray opened' event that we fail to report to
guests. After doing this, older Linux guests properly revalidate a disc
on the change command. HSM violation errors, which caused Linux guests
to do a soft-reset of the link, also go away:
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
sr 1:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00
ata2.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0
res 01/60:00:00:00:00/00:00:00:00:00/a0 Emask 0x3 (HSM violation)
ata2.00: status: { ERR }
ata2: soft resetting link
ata2.00: configured for MWDMA2
ata2: EH complete
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Tested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Implement the 'media' sub-command of the GET_EVENT_STATUS_NOTIFICATION
command. This helps us report tray open, tray closed, no media, media
present states to the guest.
Newer Linux kernels (2.6.38+) rely on this command to revalidate discs
after media change.
This patch also sends out tray open/closed status to the guest driver
when requested e.g. via the CDROM_DRIVE_STATUS ioctl (thanks Markus).
Without such notification, the guest and qemu's tray open/close status
was frequently out of sync, causing installers like Anaconda detecting
no disc instead of tray open, confusing them terribly.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Handle GET_EVENT_STATUS_NOTIFICATION's No Event Available response in a
generic way so that future additions to the code to handle other
response types is easier.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of using magic numbers, use structs that are more descriptive of
the fields being used.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This makes the code more readable.
Also, there's a block like:
if () {
...
} else {
...
}
Split that into
if () {
...
return;
}
...
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
After a media change, the only commands allowed from the guest were
REQUEST_SENSE and INQUIRY. The guest may also issue
GET_EVENT_STATUS_NOTIFICATION commands to get media
changed notification.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Table 629 of the MMC-5 spec mentions two different error conditions when
a CDROM eject is requested: a) while a disc is inserted and b) while a
disc is not inserted.
Ensure we return the appropriate error for the present condition of the
drive and disc status.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Drivers are free to lock drives without any media present. Such a
condition should not result in an error condition.
See Table 341 in MMC-5 spec for details.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
factor out ide initialization to call drive_get(IF_IDE)
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
* 'for-anthony' of git://github.com/bonzini/qemu:
remove qemu_get_clock
add a generic scaling mechanism for timers
change all other clock references to use nanosecond resolution accessors
change all rt_clock references to use millisecond resolution accessors
add more helper functions with explicit milli/nanosecond resolution
This was done with:
sed -i 's/qemu_get_clock\>/qemu_get_clock_ns/' \
$(git grep -l 'qemu_get_clock\>' )
sed -i 's/qemu_new_timer\>/qemu_new_timer_ns/' \
$(git grep -l 'qemu_new_timer\>' )
after checking that get_clock and new_timer never occur twice
on the same line. There were no missed occurrences; however, even
if there had been, they would have been caught by the compiler.
There was exactly one false positive in qemu_run_timers:
- current_time = qemu_get_clock (clock);
+ current_time = qemu_get_clock_ns (clock);
which is of course not in this patch.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch fixes two things:
1) CHECK POWER MODE
The error return value wasn't always zero, so it would show up as
offline. Error is now explicitly set to zero.
2) SMART
The smart values that were returned were invalid and tools like skdump
would not recognize that the smart data was actually valid and would
dump weird output. The data has been fixed up and raw value support
was added. Tools like skdump and palimpsest work as expected.
Signed-off-by: Brian Wheeler <bdwheele@indiana.edu>
Acked-by: Ryan Harper <ryanh@us.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Nothing prevented IRQ sharing on the ISA bus in principle. Not all
boards supported this, neither each and every card nor driver and OS.
Still, there existed valid IRQ sharing scenarios, (at least) two of them
can also be found in QEMU: >2 PC UARTs and the PREP IDE buses.
So remove this artificial restriction from our ISA model.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Define and use dedicated constants for vm_stop reasons, they actually
have nothing to do with the EXCP_* defines used so far. At this chance,
specify more detailed reasons so that VM state change handlers can
evaluate them.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Different AHCI controllers have a different number of ports, so the core
shouldn't care about the amount of ports available.
This patch makes the number of ports available to the AHCI core runtime
configurable, allowing us to have multiple different AHCI implementations
with different amounts of ports.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The ahci code was missing its soft reset functionality. This wasn't really an
issue for Linux guests, but Windows gets confused when the controller doesn't
reset when it tells it so.
Using this patch I can now successfully boot Windows 7 from AHCI using AHCI
enabled SeaBIOS.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The drive sends a d2h init fis on initialization. Usually, the guest doesn't
receive fises yet at that point though, so the delivery is deferred.
Let's reflect that by sending the init fis on fis receive enablement.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sebastian's patch already did a pretty good job at splitting up ICH-9
AHCI code and the AHCI core. We need some more though. Copyright was missing,
the lspci dump belongs to ICH-9, we don't need the AHCI core to have its
own qdev device duplicate.
So let's split them a bit more in this patch, making things easier to
read an understand.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Due to popular request, this patch adds a license header to ahci.h
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There are multiple ahci devices out there. The currently implemented ich-9
is only one of the many. So let's split that one out into a separate file
to stress the difference.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Before commit 622b520f, index=12 meant bus=1,unit=5.
Since the commit, it means bus=0,unit=12. The drive is created, but
not the guest device. That's because the controllers we use with
if=scsi drives (lsi53c895a and esp) support only 7 units, and
scsi_bus_legacy_handle_cmdline() ignores drives with unit numbers
exceeding that limit.
Changing the mapping of index to bus, unit is a regression. Breaking
-drive invocations that used to work just makes it worse.
Revert the part of commit 622b520f that causes this, and clean up
some.
Note that the fix only affects if=scsi. You can still put more than 7
units on a SCSI bus with -device & friends.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The len and is_write arguments to cpu_physical_memory_unmap() were
swapped. This patch changes calls to use the correct argument ordering.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Extend the change_cb callback with a reason argument, and use it
to tell drivers about size changes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
With bm == NULL, other code in the same function would crash.
This bug was reported by cppcheck:
hw/ide/pci.c:280: error: Possible null pointer dereference: bm
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Merge ide_dma_submit_check into it's only caller. Also use tail recursion
using a goto instead of a real recursion - this avoid overflowing the
stack in the pathological situation of an recurring error that is ignored.
We'll still be busy looping in ide_dma_cb, but at least won't eat up
all stack space after this.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Currenly the code only resets the io_buffer_index field for reads,
but the code seems to expect this for all types of I/O. I guess
we simply don't hit large enough transfers that would require this
often enough.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Factor the DMA I/O path that is duplicated between read and write
commands, into common helpers using the s->is_read flag added for
the macio ATA controller.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch tags all pci devices which belong to the piix3/4 chipsets as
not hotpluggable (Host bridge, ISA bridge, IDE controller, ACPI bridge).
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Avoid these warnings with GCC 4.6.0:
/src/qemu/hw/ide/ahci.c: In function 'ahci_reset_port':
/src/qemu/hw/ide/ahci.c:810:14: error: variable 'tfd' set but not used [-Werror=unused-but-set-variable]
/src/qemu/hw/ide/ahci.c: In function 'handle_cmd':
/src/qemu/hw/ide/ahci.c:1103:19: error: variable 'pr' set but not used [-Werror=unused-but-set-variable]
In the tfd variable case, fix the logic also.
CC: Alexander Graf <agraf@suse.de>
CC: Kevin Wolf <kwolf@redhat.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
We register the vm change state handler in a PCI BAR map() function.
This function can be called multiple times throughout the lifetime of a
PCI IDE device. This results in duplicate vm change state handlers
being register, none of which are ever unregistered.
Instead, register the vm change state handler in the device's init
function once and for all.
piix tested, cmd646 and via not tested.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
ATAPI also can do ncq, so let's expose the capability.
This patch makes CD-ROM support work on Windows 7 for me.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Set SATA Mode Select to AHCI in the Address Map Register.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds an emulation layer for an ICH-9 AHCI controller. For now
this controller does not do IDE legacy emulation. It is a pure AHCI controller.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
I modified ide_identify() to include the zero-based queue length
value in word 75, and set bit 8 in word 76 to signal NCQ support
in the identify data for AHCI SATA drives.
Signed-off-by: Roland Elek <elek.roland@gmail.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We hook into transfer_start and immediately call the end function
for ahci. This means that everything needs to be in place for the
end function when we start the transfer, so let's move the function
down to where all state is in place.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The ATA core is currently heavily intertwined with BMDMA code. Let's loosen
that a bit, so we can happily replace the DMA backend with different
implementations.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that we have the function split out, we have to reindent it.
In order to increase the readability of the actual functional change,
this is split out.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The ATA command interpretation code can be used for PATA and SATA
interfaces alike. So let's split it out into a separate function.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
If bootindex is specified on command line a string that describes device
in firmware readable way is added into sorted list. Later this list will
be passed into firmware to control boot order.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Store all io ports used by device in ISADevice structure.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Add "fw_name" to DeviceInfo to use in device path building. In
contrast to "name" "fw_name" should refer to functionality device
provides instead of particular device model like "name" does.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
As stated before, devices can be little, big or native endian. The
target endianness is not of their concern, so we need to push things
down a level.
This patch adds a parameter to cpu_register_io_memory that allows a
device to choose its endianness. For now, all devices simply choose
native endian, because that's the same behavior as before.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Whenever SSBM is reset in the command register all state information is lost.
Restarting DMA means that current_addr must be reset to the base address of the
PRD table. The OS is not required to change the base address register before
starting a DMA operation, it can reuse the value it wrote for an earlier
request.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
You can only start a DMA transfer if it's not running yet, and you can only
cancel it if it's running.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
BMIDEA in the status register must be cleared on error. This makes FreeBSD
respond (more) correctly to I/O errors.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Several places that stop a DMA transfer duplicate this code. Factor it out into
a common function.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
There is no need for these type casts (as other existing
code shows). So re-write the first argument without
type cast (and remove a related TODO comment).
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Instead of always assuming success for bdrv_aio_flush, actually do something
with the error. This respects the werror option and accordingly ignores the
error, reports it to the guest or stops the VM and retries after cont.
Ignoring the error is trivial, obviously. For stopping the VM and retrying
later old code can be reused, but we need to introduce a new status for "retry
a flush". For reporting to the guest, fortunately the same action is required
as for a failed read/write (status = DRDY | ERR, error = ABRT), so this code
can be reused as well.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
ATA does not only have the WCACHE enabled bit in identify word 85, but also
a WCACHE supported bit in word 82. While the Linux kernel is fine with the
latter at least hdparm also needs the former before correctly displaying
the cache settings. There's also a non-zero chance other operating systems
are more picky in their volatile write cache detection.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
IDE is a bit ugly in this respect. For one it doesn't really keep track
of a sector size - most of the protocol is in units of 512 bytes, and we
assume 2048 bytes for CDROMs which is correct most of the time.
Second IDE allocates an I/O buffer long before we know if we're dealing
with a CDROM or not, so increase the alignment for the io_buffer
unconditionally.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Fill in word 64 of IDENTIFY data to indicate support for PIO modes 3 and 4.
This allows NetBSD guests to use UltraDMA modes instead of just PIO mode 0.
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Changing block.h or blockdev.h resulted in recompiling most objects.
Move DriveInfo typedef and BlockInterfaceType enum definitions
to qemu-common.h and rearrange blockdev.h use to decrease churn.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The reason for not actually canceling the I/O is because with
virtualization and lots of VM running, a guest fs may mistake a
overload of the host, as an IDE timeout. So rather than canceling the
I/O, it's safer to wait I/O completion and simulate that the I/O has
completed just before the io cancellation was requested by the
guest. This way if ntfs or an app writes data without checking for
-EIO retval, and it thinks the write has succeeded, it's less likely
to run into troubles. Similar issues for reads.
Furthermore because the DMA operation is splitted into many synchronous
aio_read/write if there's more than one entry in the SG table, without this
patch the DMA would be cancelled in the middle, something we've no idea if it
happens on real hardware too or not. Overall this seems a great risk for zero
gain.
This approach is sure safer than previous code given we can't pretend all guest
fs code out there to check for errors and reply the DMA if it was completed
partially, given a timeout would never materialize on a real harddisk unless
there are defective blocks (and defective blocks are practically only an issue
for reads never for writes in any recent hardware as writing to blocks is the
way to fix them) or the harddisk breaks as a whole.
Signed-off-by: Izik Eidus <ieidus@redhat.com>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
* 'for-anthony' of git://repo.or.cz/qemu/kevin:
Fix -snapshot deleting images on disk change
block: Use error codes from lower levels for error message
block: default to 0 minimal / optiomal I/O size
move 'unsafe' to end of caching modes in help
virtio-blk: Create exit function to unregister savevm
block migration: propagate return value when bdrv_write() returns < 0
ide/atapi: add support for GET EVENT STATUS NOTIFICATION
Fix the following warnings:
/src/qemu/hw/ide/core.c: In function `ide_drive_pio_post_load':
/src/qemu/hw/ide/core.c:2767: warning: comparison is always false due to limited range of data type
/src/qemu/ui/vnc-enc-tight.c: In function `tight_detect_smooth_image':
/src/qemu/ui/vnc-enc-tight.c:284: warning: comparison is always true due to limited range of data type
/src/qemu/ui/vnc-enc-tight.c:297: warning: comparison is always true due to limited range of data type
/src/qemu/ui/vnc-enc-tight.c: In function `tight_encode_indexed_rect16':
/src/qemu/ui/vnc-enc-tight.c:456: warning: comparison is always false due to limited range of data type
/src/qemu/ui/vnc-enc-tight.c: In function `tight_encode_indexed_rect32':
/src/qemu/ui/vnc-enc-tight.c:457: warning: comparison is always false due to limited range of data type
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
It reintroduces
Revert "ide save/restore pio/atapi cmd transfer fields and io buffer"
but using subsections. Added bonus is the addition of ide_dummy_transfer_stop
to transfer_end_table, that was missing.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This reverts commit ed487bb1d6.
The conflicts are due to commit 4fc8d6711a
that is a fix to the ide_drive_pre_save() function. It reverts both
(and both are reinstantiated later in the series)
Conflicts:
hw/ide/core.c
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The GET EVENT STATUS NOTIFICATION is a mandatory command according
to MMC-3, even if event status notification is not supported.
This patch adds support for this command. It returns NEA ("No Event
Available") with an empty "Supported Event Classes" to show that it
doesn't event support status notification. If asychronous operation is
requested, which requires NCQ support, it returns an error according
to the specifications.
This fixes HAL support on FreeBSD and derivatives, which fill up the
logs every second with:
acd0: FAILURE - unknown CMD (0x03) ILLEGAL REQUEST asc=0x20 ascq=0x00
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Disks without media make no sense. For SCSI, a Linux guest kernel
complains during boot. I didn't try other combinations.
scsi-generic doesn't need the additional check, because it already
requires bdrv_is_sg(), which fails without media.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The file, vt82c686.c, was added after the change set of
b80d4a9887 and
fecb93c45c
are created, but before the patch series was commit.
So similar fix is needed to vt82c686.c.
Cc: Huacai Chen <zltjiangshi@gmail.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Don't overwrite pci header type.
Otherwise, multi function bit which pci_init_header_type() sets
appropriately is lost.
Anyway PCI_HEADER_TYPE_NORMAL is zero, so it is unnecessary to zero
which is already zero cleared.
how to test:
run qemu and issue info pci to see whether a device in question is
normal device, not pci-to-pci bridge.
This is handy because guest os isn't required.
tested changes:
The following files are covered by using following commands.
sparc64-softmmu
apb_pci.c, vga-pci.c, cmd646.c, ne2k_pci.c, sun4u.c
ppc-softmmu
grackle_pci.c, cmd646.c, ne2k_pci.c, vga-pci.c, macio.c
ppc-softmmu -M mac99
unin_pci.c(uni-north, uni-north-agp)
ppc64-softmmu
pci-ohci, ne2k_pci, vga-pci, unin_pci.c(u3-agp)
x86_64-softmmu
acpi_piix4.c, ide/piix.c, piix_pci.c
-vga vmware vmware_vga.c
-watchdog i6300esb wdt_i6300esb.c
-usb usb-uhci.c
-sound ac97 ac97.c
-nic model=rtl8139 rtl8139.c
-nic model=pcnet pcnet.c
-balloon virtio virtio-pci.c:
untested changes:
The following changes aren't tested.
prep_pci.c: ppc-softmmu -M prep should cover, but core dumped.
unin_pci.c(uni-north-pci): the caller is commented out.
openpic.c: the caller is commented out in ppc_prep.c
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
These will be used to generate unique id strings for ramblocks. The name
field is required, the device pointer is optional as most callers don't
have a device. When there's no device or the device isn't a child of
a bus implementing BusInfo.get_dev_path, the name should be unique for
the platform.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When available, we'd like to be able to access the DeviceState
when registering a savevm. For buses with a get_dev_path()
function, this will allow us to create more unique savevm
id strings.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
drive_init() doesn't permit invalid CHS for if=ide, but that's
worthless: we get it via if=none and -device.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
drive_init() doesn't permit option readonly for if=ide, but that's
worthless: we get it via if=none and -device.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It still always succeeds. The next commits will add failures.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The two aren't independent variables. Make that obvious.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Use error_report(), because it points to the error location.
Reword "tried to assign twice" messages to make it clear that we're
complaining about the unit property.
Report invalid unit property instead of failing silently.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Drives defined with -drive if=ide get get created along with the IDE
controller, inside machine->init(). That's before cmos_init().
Drives defined with -device get created during generic device init.
That's after cmos_init(). Because of that, CMOS has no information on
them (type, geometry, translation). Older versions of Windows such as
XP reportedly choke on that.
Split off the part of CMOS initialization that needs to know about
-device devices, and turn it into a reset handler, so it runs after
device creation.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
BlockDriverState member removable controls whether virtual media
change (monitor commands change, eject) is allowed. It is set when
the "type hint" is BDRV_TYPE_CDROM or BDRV_TYPE_FLOPPY.
The type hint is only set by drive_init(). It sets BDRV_TYPE_FLOPPY
for if=floppy. It sets BDRV_TYPE_CDROM for media=cdrom and if=ide,
scsi, xen, or none.
if=ide and if=scsi work, because the type hint makes it a CD-ROM.
if=xen likewise, I think.
For the same reason, if=none works when it's used by ide-drive or
scsi-disk. For other guest devices, there are problems:
* fdc: you can't change virtual media
$ qemu [...] -drive if=none,id=foo,... -global isa-fdc.driveA=foo
QEMU 0.12.50 monitor - type 'help' for more information
(qemu) eject foo
Device 'foo' is not removable
unless you add media=cdrom, but that makes it readonly.
* virtio: if you add media=cdrom, you can change virtual media. If
you eject, the guest gets I/O errors. If you change, the guest sees
the drive's contents suddenly change.
* scsi-generic: if you add media=cdrom, you can change virtual media.
I didn't test what that does to the guest or the physical device,
but it can't be pretty.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
For instance, -device scsi-disk,drive=foo -device scsi-disk,drive=foo
happily creates two SCSI disks connected to the same block device.
It's all downhill from there.
Device usb-storage deliberately attaches twice to the same blockdev,
which fails with the fix in place. Detach before the second attach
there.
Also catch attempt to delete while a guest device model is attached.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Make the property point to BlockDriverState, cutting out the DriveInfo
middleman. This prepares the ground for block devices that don't have
a DriveInfo.
Currently all user-defined ones have a DriveInfo, because the only way
to define one is -drive & friends (they go through drive_init()).
DriveInfo is closely tied to -drive, and like -drive, it mixes
information about host and guest part of the block device. I'm
working towards a new way to define block devices, with clean
host/guest separation, and I need to get DriveInfo out of the way for
that.
Fortunately, the device models are perfectly happy with
BlockDriverState, except for two places: ide_drive_initfn() and
scsi_disk_initfn() need to check the DriveInfo for a serial number set
with legacy -drive serial=... Use drive_get_by_blockdev() there.
Device model code should now use DriveInfo only when explicitly
dealing with drives defined the old way, i.e. without -device.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
All callers of ide_create_drive() ignore its value. Currently
harmless, because it fails only when qdev_init() fails, which fails
only when ide_drive_initfn() fails, which never fails.
Brittle. Change it to die instead of silently ignoring failure.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
That's where they belong semantically (block device host part), even
though the actions are actually executed by guest device code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Anything that moves hundreds of lines out of vl.c can't be all bad.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Show the actual default value instead of <null> when the property has
not been set.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It needs to be a qdev property, because it belongs to the drive's
guest part.
Bonus: info qtree now shows the serial number.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
IDEState members drive_serial_str and version are now left empty until
an actual drive is connected. Before, they got a default value that
was overwritten when a drive got connected. Doesn't matter, because
they're used only while a drive is connected.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit 428c149b added IDEState member conf to let commit 0009baf1 find
the BlockConf from there. It exists only for qdev drives, created via
ide_drive_initfn(), not for drives created via ide_init2().
But for a qdev drive, we can just as well reach its IDEDevice, which
contains the BlockConf. Do that, and revert the parts of commit
428c149b that add IDEState member conf.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When cancelling a request, bdrv_aio_cancel may decide that it waits for
completion of a request rather than for cancellation. IDE therefore can't
abandon its DMA status before calling bdrv_aio_cancel; otherwise the callback
of a completed request would use invalid data.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We cannot install different opaque pointer for read and write
of the same i/o address.
- handle zero address in bmdma_writeb_common and install
the same opaque pointer for both read and write access.
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Instead of doing tricks to get the pci_dev, just pass it in the 1st
place. Patch is a bit longer that reverting the pci_dev field, but it
states more clearly (IMHO) what we are doing.
It also fixes the bm test, now that you told me that ->unit is not
always valid.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Make win2k install hack unconditional as it is still restricted to
x86 only in vl.c.
Replace TARGET_PAGE_SIZE and 4096 with PAGE_SIZE.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The next commit will move the STOP event into do_vm_stop(), to
have the expected event sequence we need to emit the I/O error
event before calling vm_stop().
The expected sequence is:
{ "event": "BLOCK_IO_ERROR" [...] }
{ "event": "STOP" }
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
/src/qemu/hw/ide/core.c: In function 'ide_drive_pre_save':
/src/qemu/hw/ide/core.c:2740: warning: comparison is always false due to limited range of data type
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Save/restore information necessary to continue in progress PIO/ATAPI CMD
transfers.
This includes the IO buffer.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Export the physical block size in the ATA IDENTIFY command. The
other topology values are not supported in ATA so skip them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add three new qdev properties to export block topology information to
the guest. This is needed to get optimal I/O alignment for RAID arrays
or SSDs.
The options are:
- physical_block_size to specify the physical block size of the device,
this is going to increase from 512 bytes to 4096 kilobytes for many
modern storage devices
- min_io_size to specify the minimal I/O size without performance impact,
this is typically set to the RAID chunk size for arrays.
- opt_io_size to specify the optimal sustained I/O size, this is
typically the RAID stripe width for arrays.
I decided to not auto-probe these values from blkid which might easily
be possible as I don't know how to deal with these issues on migration.
Note that we specificly only set the physical_block_size, and not the
logial one which is the unit all I/O is described in. The reason for
that is that IDE does not support increasing the logical block size and
at last for now I want to stick to one meachnisms in queue and allow
for easy switching of transports for a given backing image which would
not be possible if scsi and virtio use real 4k sectors, while ide only
uses the physical block exponent.
To make this more common for the different block drivers introduce a
new BlockConf structure holding all common block properties and a
DEFINE_BLOCK_PROPERTIES macro to add them all together, mirroring
what is done for network drivers. Also switch over all block drivers
to use it, except for the floppy driver which has weird driveA/driveB
properties and probably won't require any advanced block options ever.
Example usage for a virtio device with 4k physical block size and
8k optimal I/O size:
-drive file=scratch.img,media=disk,cache=none,id=scratch \
-device virtio-blk-pci,drive=scratch,physical_block_size=4096,opt_io_size=8192
aliguori: updated patch to take into account BLOCK events
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Just call bdrv_mon_event() in the right place.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If migration takes place between write of the bmdma address register and
write of the command register (to initiate DMA), the destination will
not properly start the DMA op, hanging the guest:
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.00: cmd c8/00:16:41:00:00/00:00:00:00:00/e0 tag 0 dma 11264 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
Fix by sending current transfer information in the migration data.
We need to update ide version to 4 for this to work. As we don't
have subsectios, we need to chain the update increase until
vmstate_ide_pci (quintela)
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds a new property named 'ver' to ide-drive which allows to
specify the version which the virtual disk/cdrom should report to the
guest. By default this is the qemu version (i.e. 0.12). usage:
-drive if=none,id=disk,file=...
-device ide-drive,bus=ide.0,unit=0,drive=disk,ver=42
You can also switch the version for all ide drives using:
-global ide-drive.ver=42
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
This is a workaround only, and is a partial revert
of a few changes to BMDMAState which removed pci_dev
field on the way.
- cmd646 pci_from_bm() expects bm->unit value to
correspond with bm data being passed to callback
as opaque pointer. This breaks when write to dma
control register of second channel happens when no
dma operation is in progress, so bm->unit is zero
for second channel, and pci_from_bm() returns garbage
pointer. Crash happens shortly after that while
dereferencing that pointer.
v0->v1: cleaned up dead code from pci_from_bm.
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Device names with whitespace require quoting in the shell and in the
monitor. Some of the offenders are also overly long. Some have a
more convenient alias, some don't.
The place for verbose device names is DeviceInfo member desc. The
name should be short & sweet.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This implements the audio control or volume read support as needed by
some systems. A Conectiva Parolin system required this to detect an IDE
device as CD-ROM, through the CDVOLREAD ioctl.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Some PAGE constants were used instead of the macros we already have
defined in internal.h.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Either rename variables and functions to refer to write errors (which is what
they actually do) or introduce a parameter to distinguish reads and writes.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch is preliminary for 64 bit BAR support.
Introduce dedicated type, pcibus_t, to represent pci bus address/size
instead of uint32_t.
Later this type will be changed to uint64_t.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
make constants for pci base address match pci_regs.h by
renaming PCI_ADDRESS_SPACE_xxx to PCI_BASE_ADDRESS_SPACE_xxx.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
These devices are created automatically, and attempting to create
another one with -device fails with "qemu: hardware error:
register_ioport_write: invalid opaque".
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Problem: x86 systems could not survive a few system_resets.
Clear most of IDE state when reset. Implement the missing reset handlers.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
There is absolutely no need to call reset functions when initializing
devices. Since we are already registering them, calling qemu_system_reset()
should suffice. Actually, it is what happens when we reboot the machine,
and using the same process instead of a special case semantics will even
allow us to find bugs easier.
Furthermore, the fact that we initialize things like the cpu quite early,
leads to the need to introduce synchronization stuff like qemu_system_cond.
This patch removes it entirely. All we need to do is call qemu_system_reset()
only when we're already sure the system is up and running
I tested it with qemu (with and without io-thread) and qemu-kvm, and it
seems to be doing okay - although qemu-kvm uses a slightly different patch.
[ v2: user mode still needs cpu_reset, so put it in ifdef. ]
[ v3: leave qemu_system_cond for now. ]
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Change pointer to struct by embedded struct.
Adjust all callers
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
It is used everywhere as uint8_t except in one place. Cast to uint16_t
in that place
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
We have split the functions that needed it for cmd646
Patchworks-ID: 35302
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch splits cmd646 specific code from pci.c.
This patch splits piix4 specific code from pci.c.
And compile new piix.o and cmd646.o when they are needed.
The only change that is not code movemet is removal of cmd646 specific parts
in bmdma_readb/writeb for piix.
Patchworks-ID: 35301
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
We already have a PCIDevice at that point
Patchworks-ID: 35296
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Some callers test for != 0, some for < 0. Normalize to < 0.
Patchworks-ID: 35171
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Like qdev_init(), but terminate program via hw_error() instead of
returning an error value.
Use it instead of qdev_init() where terminating the program on failure
is okay, either because it's during machine construction, or because
we know that failure can't happen.
Because relying in the latter is somewhat unclean, and the former is
not always obvious, it would be nice to go back to qdev_init() in the
not-so-obvious cases, only with proper error handling. I'm leaving
that for another day, because it involves making sure that error
values are properly checked by all callers.
Patchworks-ID: 35168
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
It's qdev_create() specialized for PCI, so name it accordingly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
In the very least, a change like this requires discussion on the list.
The naming convention is goofy and it causes a massive merge problem. Something
like this _must_ be presented on the list first so people can provide input
and cope with it.
This reverts commit 99a0949b72.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
With this patch applied ide drives (when attached to a pci adapter) can
be created via -device, like this:
-drive if=none,id=mydisk,file=/path/to/disk.img
-device ide-drive,drive=mydisk,bus=ide.0,unit=0
Note that creating a master on ide1 doesn't work that way. That is a
side effect of qemu creating a cdrom automagically even if you don't
ask for it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This allows the ide bus being initialized without drives attached
and the drives being attached and initialization later on as
separate step.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Add a enable_write_cache flag in the block driver state, and use it to
decide if we claim to have a volatile write cache that needs controlled
flushing from the guest. The flag is off if cache=writethrough is
defined because O_DSYNC guarantees that every write goes to stable
storage, and it is on for cache=none and cache=writeback.
Both scsi-disk and ide now use the new flage, changing from their
defaults of always off (ide) or always on (scsi-disk).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
8baf73adf6 (qdev/isa: convert fdc)
breaks MIPS Malta:
Tried to create isa device isa-fdc with no isa bus present
Fix this by creating an isa bus for piix4.
This change also requires some more qdev related changes
(similar changes were applied to pc.c) and allows
cleaning of piix3/piix4 code.
Thanks to Gerd Hoffmann for his hints.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
These variables are per bus, not per drive. Lets move them and
cleanup things a bit. And fix the cmd migration bug for real.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
