POWER10 adds support for StoreEOI operation and 64K ESB pages on PSIHB
to be consistent with the other interrupt sources of the system.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
and use a pnv_chip_power10_quad_realize() helper to avoid code
duplication with P9. This still needs some refinements on the XSCOM
registers handling in PnvQuad.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Our OCC model is very mininal and POWER10 can simply reuse the OCC
model we introduced for POWER9.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The XIVE2 interrupt controller of the POWER10 processor follows the
same logic than on POWER9 but the HW interface has been largely
reviewed. It has a new register interface, different BARs, extra
VSDs, new layout for the XIVE2 structures, and a set of new features
which are described below.
This is a model of the POWER10 XIVE2 interrupt controller for the
PowerNV machine. It focuses primarily on the needs of the skiboot
firmware but some initial hypervisor support is implemented for KVM
use (escalation).
Support for new features will be implemented in time and will require
new support from the OS.
* XIVE2 BARS
The interrupt controller BARs have a different layout outlined below.
Each sub-engine has now own its range and the indirect TIMA access was
replaced with a set of pages, one per CPU, under the IC BAR:
- IC BAR (Interrupt Controller)
. 4 pages, one per sub-engine
. 128 indirect TIMA pages
- TM BAR (Thread Interrupt Management Area)
. 4 pages
- ESB BAR (ESB pages for IPIs)
. up to 1TB
- END BAR (ESB pages for ENDs)
. up to 2TB
- NVC BAR (Notification Virtual Crowd)
. up to 128
- NVPG BAR (Notification Virtual Process and Group)
. up to 1TB
- Direct mapped Thread Context Area (reads & writes)
OPAL does not use the grouping and crowd capability.
* Virtual Structure Tables
XIVE2 adds new tables types and also changes the field layout of the END
and NVP Virtualization Structure Descriptors.
- EAS
- END new layout
- NVT was splitted in :
. NVP (Processor), 32B
. NVG (Group), 32B
. NVC (Crowd == P9 block group) 32B
- IC for remote configuration
- SYNC for cache injection
- ERQ for event input queue
The setup is slighly different on XIVE2 because the indexing has changed
for some of the tables, block ID or the chip topology ID can be used.
* XIVE2 features
SCOM and MMIO registers have a new layout and XIVE2 adds a new global
capability and configuration registers.
The lowlevel hardware offers a set of new features among which :
- a configurable number of priorities : 1 - 8
- StoreEOI with load-after-store ordering is activated by default
- Gen2 TIMA layout
- A P9-compat mode, or Gen1, TIMA toggle bit for SW compatibility
- increase to 24bit for VP number
Other features will have some impact on the Hypervisor and guest OS
when activated, but this is not required for initial support of the
controller.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Determine the IRQ number in the same way as for pnv_dt_ipmi_bt(). This
resolves one usage of ISADevice::isairq[] which allows it to be removed
eventually.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220301220037.76555-6-shentey@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This patch introduces pnv-phb4 user creatable devices that are created
in a similar manner as pnv-phb3 devices, allowing the user to interact
with the PHBs directly instead of creating PCI Express Controllers that
will create a certain amount of PHBs per controller index.
We accomplish this by doing the following:
- add a pnv_phb4_get_stack() helper to retrieve which stack an user
created phb4 would occupy;
- when dealing with an user created pnv-phb4 (detected by checking if
phb->stack is NULL at the start of phb4_realize()), retrieve its stack
and initialize its properties as done in stk_realize();
- use 'defaults_enabled()' in stk_realize() to avoid creating and
initializing a 'stack->phb' qdev that might be overwritten by an user
created pnv-phb4 device. This process is wrapped into a new helper
called pnv_pec_stk_default_phb_realize().
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220111131027.599784-5-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It is not used elsewhere so that's where it belongs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220105212338.49899-10-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
PHB3s ared SysBus devices and should be allowed to be dynamically
created.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220105212338.49899-9-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The powernv machine uses the object hierarchy to populate the device
tree and each device should be parented to the chip it belongs to.
This is not the case for user created devices which are parented to
the container "/unattached".
Make sure a PHB3 device is parented to its chip by reparenting the
object if necessary.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220105212338.49899-8-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
PHB3 devices and PCI devices can now be added to the powernv8 machine
using :
-device pnv-phb3,chip-id=0,index=1 \
-device nec-usb-xhci,bus=pci.1,addr=0x0
The 'index' property identifies the PHB3 in the chip. In case of user
created devices, a lookup on 'chip-id' is required to assign the
owning chip.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220105212338.49899-7-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This cleanups the PHB3 model a bit more since the root port is an
independent device and it will ease our task when adding user created
PHB3s.
pnv_phb_attach_root_port() is made public in pnv.c so it can be reused
with the pnv_phb4 root port later.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220105212338.49899-4-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The POWER8 processors with a NVLink logic unit have 4 PHB3 devices per
chip.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20211222063817.1541058-2-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When -nodefaults is supported for PHB4 devices, the pecs array under
the chip will be empty. This will break the 'info pic' HMP command.
Do a QOM loop on the chip children and look for PEC PHB4 devices
instead.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20211213132830.108372-15-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This change will help us providing support for user created PHB4
devices.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-14-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is not useful and will be in the way for support of user created
PHB4 devices.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-13-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Use the num_stacks class attribute to compute the PHB index depending
on the PEC index :
* PEC0 provides 1 PHB (PHB0)
* PEC1 provides 2 PHBs (PHB1 and PHB2)
* PEC2 provides 3 PHBs (PHB3, PHB4 and PHB5)
The routine pnv_pec_phb_offset() is a bit complex but it also prepares
ground for PHB5 which has a different layout of stacks: 3 per PECs.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-12-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Each PEC device of the POWER9 chip has a predefined number of stacks,
equivalent of a root port complex:
PEC0 -> 1 stack
PEC1 -> 2 stacks
PEC2 -> 3 stacks
Introduce a class attribute to hold these values and remove the
"num-stacks" property.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-11-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
And check the PEC index using the chip class.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-10-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It prepares ground for PHB5 which has different values.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-9-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
POWER9 processor comes with 3 PHB4 PEC (PCI Express Controller) and
each PEC can have several PHBs :
* PEC0 provides 1 PHB (PHB0)
* PEC1 provides 2 PHBs (PHB1 and PHB2)
* PEC2 provides 3 PHBs (PHB3, PHB4 and PHB5)
A num_pecs class attribute represents better the logic units of the
POWER9 chip. Use that instead of num_phbs which fits POWER8 chips.
This will ease adding support for user created devices.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-8-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When -nodefaults is supported for PHB3 devices, the phbs array under
the chip will be empty. This will break the XICSFabric handlers, and
all interrupt delivery, and the 'info pic' HMP command.
Do a QOM loop on the chip children and look for PHB3 devices instead.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20211213132830.108372-7-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This change will help us providing support for user created PHB3
devices.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-6-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It is never used.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-5-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This change will help us move the mapping of XSCOM regions under the
PHB3 realize routine, which will be necessary for user created PHB3
devices.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Setting -uuid in the pnv machine does not work:
./qemu-system-ppc64 -machine powernv8,accel=tcg -uuid 7ff61ca1-a4a0-4bc1-944c-abd114a35e80
qemu-system-ppc64: error creating device tree: (fdt_property_string(fdt, "system-id", buf)): FDT_ERR_BADSTATE
This happens because we're using fdt_property_string(), which is a
sequential write function that is supposed to be used when we're
building a new FDT, in a case where read/writing into an existing FDT.
Fix it by using fdt_setprop_string() instead.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20211207094858.744386-1-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
If one tries to use -machine powernv9,accel=kvm in a Power9 host, a
cryptic error will be shown:
qemu-system-ppc64: Register sync failed... If you're using kvm-hv.ko, only "-cpu host" is possible
qemu-system-ppc64: kvm_init_vcpu: kvm_arch_init_vcpu failed (0): Invalid argument
Appending '-cpu host' will throw another error:
qemu-system-ppc64: invalid chip model 'host' for powernv9 machine
The root cause is that in IBM PowerPC we have different specs for the bare-metal
and the guests. The bare-metal follows OPAL, the guests follow PAPR. The kernel
KVM modules presented in the ppc kernels implements PAPR. This means that we
can't use KVM accel when using the powernv machine, which is the emulation of
the bare-metal host.
All that said, let's give a more informative error in this case.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20211130133153.444601-2-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210902130928.528803-3-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This to avoid possible conflicts with the "id" property of QOM objects.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210901094153.227671-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
But always give the first 1GB to chip 0 as skiboot requires it.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210809134547.689560-6-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the QEMU PowerNV machine was introduced, multi chip support
modeled a two socket system with dual chip modules as found on some P8
Tuleta systems (8286-42A). But this is hardly used and not relevant
for QEMU. Use a simple index instead.
With this change, we can now increase the max socket number to 16 as
found on high end systems.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210809134547.689560-5-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There is no need to keep the DD1 chip model as it will never be
publicly available.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210809134547.689560-3-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Moved has_spr to cpu.h as ppc_has_spr and turned it into an inline function.
Change spr verification in pnv.c and spapr.c to a version that can
compile in a !TCG environment.
Signed-off-by: Lucas Mateus Castro (alqotel) <lucas.araujo@eldorado.org.br>
Message-Id: <20210507164146.67086-1-lucas.araujo@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Stop including exec/address-spaces.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-5-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Stop including hw/boards.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-3-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Many files include qemu/log.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210328054833.2351597-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This to map the PNOR from the machine init handler directly and finish
the cleanup of the LPC model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-8-clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The current settings are useful to load large kernels (with debug) but
it moves the initrd image in a memory region not protected by
skiboot. If skiboot is compiled with DEBUG=1, memory poisoning will
corrupt the initrd.
Cc: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-4-clg@kaod.org>
Reviewed-by: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20201026143028.3034018-11-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201016145346.27167-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Builds enabling GCOV can be bigger than 4MB and the limit on FSP
systems is 16MB.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20201002091440.1349326-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When all we do with an Error we receive into a local variable is
propagating to somewhere else, we can just as well receive it there
right away. Convert
if (!foo(..., &err)) {
...
error_propagate(errp, err);
...
return ...
}
to
if (!foo(..., errp)) {
...
...
return ...
}
where nothing else needs @err. Coccinelle script:
@rule1 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
binary operator op;
constant c1, c2;
symbol false;
@@
if (
(
- fun(args, &err, args2)
+ fun(args, errp, args2)
|
- !fun(args, &err, args2)
+ !fun(args, errp, args2)
|
- fun(args, &err, args2) op c1
+ fun(args, errp, args2) op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
)
}
@rule2 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
expression var;
binary operator op;
constant c1, c2;
symbol false;
@@
- var = fun(args, &err, args2);
+ var = fun(args, errp, args2);
... when != err
if (
(
var
|
!var
|
var op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
|
return var;
)
}
@depends on rule1 || rule2@
identifier err;
@@
- Error *err = NULL;
... when != err
Not exactly elegant, I'm afraid.
The "when != lbl:" is necessary to avoid transforming
if (fun(args, &err)) {
goto out
}
...
out:
error_propagate(errp, err);
even though other paths to label out still need the error_propagate().
For an actual example, see sclp_realize().
Without the "when strict", Coccinelle transforms vfio_msix_setup(),
incorrectly. I don't know what exactly "when strict" does, only that
it helps here.
The match of return is narrower than what I want, but I can't figure
out how to express "return where the operand doesn't use @err". For
an example where it's too narrow, see vfio_intx_enable().
Silently fails to convert hw/arm/armsse.c, because Coccinelle gets
confused by ARMSSE being used both as typedef and function-like macro
there. Converted manually.
Line breaks tidied up manually. One nested declaration of @local_err
deleted manually. Preexisting unwanted blank line dropped in
hw/riscv/sifive_e.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-35-armbru@redhat.com>
The object_property_set_FOO() setters take property name and value in
an unusual order:
void object_property_set_FOO(Object *obj, FOO_TYPE value,
const char *name, Error **errp)
Having to pass value before name feels grating. Swap them.
Same for object_property_set(), object_property_get(), and
object_property_parse().
Convert callers with this Coccinelle script:
@@
identifier fun = {
object_property_get, object_property_parse, object_property_set_str,
object_property_set_link, object_property_set_bool,
object_property_set_int, object_property_set_uint, object_property_set,
object_property_set_qobject
};
expression obj, v, name, errp;
@@
- fun(obj, v, name, errp)
+ fun(obj, name, v, errp)
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Convert that one manually.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Fails to convert hw/rx/rx-gdbsim.c, because Coccinelle gets confused
by RXCPU being used both as typedef and function-like macro there.
Convert manually. The other files using RXCPU that way don't need
conversion.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-27-armbru@redhat.com>
[Straightforwad conflict with commit 2336172d9b "audio: set default
value for pcspk.iobase property" resolved]
Convert
foo(..., &err);
if (err) {
...
}
to
if (!foo(..., &err)) {
...
}
for qdev_realize(), qdev_realize_and_unref(), qbus_realize() and their
wrappers isa_realize_and_unref(), pci_realize_and_unref(),
sysbus_realize(), sysbus_realize_and_unref(), usb_realize_and_unref().
Coccinelle script:
@@
identifier fun = {
isa_realize_and_unref, pci_realize_and_unref, qbus_realize,
qdev_realize, qdev_realize_and_unref, sysbus_realize,
sysbus_realize_and_unref, usb_realize_and_unref
};
expression list args, args2;
typedef Error;
Error *err;
@@
- fun(args, &err, args2);
- if (err)
+ if (!fun(args, &err, args2))
{
...
}
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Nothing to convert there; skipped.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Converted manually.
A few line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200707160613.848843-5-armbru@redhat.com>
The device introspect test in qtest emits some warnings with the
the pnv machine types during the "nodefaults" phase:
TEST check-qtest-ppc64: tests/qtest/device-introspect-test
qemu-system-ppc64: warning: machine has no BMC device. Use '-device
ipmi-bmc-sim,id=bmc0 -device isa-ipmi-bt,bmc=bmc0,irq=10' to define
one
qemu-system-ppc64: warning: machine has no BMC device. Use '-device
ipmi-bmc-sim,id=bmc0 -device isa-ipmi-bt,bmc=bmc0,irq=10' to define
one
qemu-system-ppc64: warning: machine has no BMC device. Use '-device
ipmi-bmc-sim,id=bmc0 -device isa-ipmi-bt,bmc=bmc0,irq=10' to define
one
This is expected since the pnv machine doesn't create the internal
BMC simulator fallback when "-nodefaults" is passed on the command
line, but these warnings appear in ci logs and confuse people.
Not having a BMC isn't recommended but it is still a supported
configuration, so a straightforward fix is to just silent this
warning when qtest is enabled.
Fixes: 25f3170b06 ("ppc/pnv: Create BMC devices only when defaults are enabled")
Reported-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159280903824.485572.831378159272329707.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
qdev_prop_set_drive() can fail. None of the other qdev_prop_set_FOO()
can; they abort on error.
To clean up this inconsistency, rename qdev_prop_set_drive() to
qdev_prop_set_drive_err(), and create a qdev_prop_set_drive() that
aborts on error.
Coccinelle script to update callers:
@ depends on !(file in "hw/core/qdev-properties-system.c")@
expression dev, name, value;
symbol error_abort;
@@
- qdev_prop_set_drive(dev, name, value, &error_abort);
+ qdev_prop_set_drive(dev, name, value);
@@
expression dev, name, value, errp;
@@
- qdev_prop_set_drive(dev, name, value, errp);
+ qdev_prop_set_drive_err(dev, name, value, errp);
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200622094227.1271650-14-armbru@redhat.com>
