It should be PXA2xxTimerInfo, not pxa2xx_timer_info. Replace all
occurences of old name with the new one.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
This is a _TEST variant of VMSTATE_STRUCT_ARRAY, necessary e.g.
for future patch changing pxa2xx_timer to use vmstate.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
Use qdev/sysbus framework to handle pxa2xx-pic. Instead of exposing IRQs
via array, reference them via qdev_get_gpio_in().
Patch has been modified by the committer.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
Final corrections for IRQ levels that are set by mst_fpga:
* Don't retranslate IRQ if previously IRQ was masked.
* After setting or clearing IRQs through register, apply mask
before setting parent IRQ level.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
VirtIOSerialDevice is like VirtIOSerialPort with just the first two
fields, which makes it pretty pointless. Using VirtIOSerialPort
directly works equally well and is less confusing.
[Amit: - rebase
- rename 'dev' to 'port' in function params in virtio-serial.h ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The SD_STATUS and SEND_NUM_WR_BLOCKS commands are supposed to cause
the card to send data back to the host. However sd.c was missing the
state change to sd_sendingdata_state for these commands, with the effect
that the Linux driver would either hang indefinitely waiting for
nonexistent data (pl181) or read zeroes and provoke a qemu warning
message (omap).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Remove the typedef SetIRQFunc, as it is not used by anything.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Nothing prevented IRQ sharing on the ISA bus in principle. Not all
boards supported this, neither each and every card nor driver and OS.
Still, there existed valid IRQ sharing scenarios, (at least) two of them
can also be found in QEMU: >2 PC UARTs and the PREP IDE buses.
So remove this artificial restriction from our ISA model.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The following patch adds PS/2 keyboard Scancode Set 3 support.
Signed-off-by: Roy Tam <roytam@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
RST bit is (1 << 4) bit, not (1 << 3), fix condition
that enables i2s if ENB is set and RST is not set.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add handling of 0xe0xx keycodes to pxa2xx_driver.
Extended keycodes in keymap should be marked with most significant
bit set (i.e. 0x80). Without this patch it's not possible to handle
i.e. cursor keys.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add emulation of KPAS register and proper emulation of
KPASMKP regs, so now driver supports multipresses and properly
works with Linux driver.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Acked-by: Andreas Färber <andreas.faerber@web.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
qemu makes it possible to disable link at tap which is not communicated
to the guest but causes all packets to be dropped.
When vhost-net is enabled, vhost needs to be aware of both the virtio
link_down and the peer link_down. we switch to userspace emulation when
either is down.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: pradeep <psuriset@linux.vnet.ibm.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The spec says: Any descriptor with a non-zero status byte has been
processed by the hardware, and is ready to be handled by the software.
Thus, once we change a descriptor status to non-zero we should
never move the head backwards and try to reuse this
descriptor from hardware.
This actually happened with a multibuffer packet
that arrives when we don't have enough buffers.
Fix by checking that we have enough buffers upfront
so we never need to discard the packet midway through.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The e1000 spec says: if software statically allocates
buffers, and uses memory read to check for completed descriptors, it
simply has to zero the status byte in the descriptor to make it ready
for reuse by hardware. This is not a hardware requirement (moving the
hardware tail pointer is), but is necessary for performing an in–memory
scan.
Thus the guest does not have to clear the status byte. In case it
doesn't we need to clear EOP for all descriptors
except the last. While I don't know of any such guests,
it's probably a good idea to stick to the spec.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: Juan Quintela <quintela@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
e1000 supports multi-buffer packets larger than rxbuf_size.
This fixes the following (on linux):
- in guest: ifconfig eth1 mtu 16110
- in host: ifconfig tap0 mtu 16110
ping -s 16082 <guest-ip>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Turn fdc_init_isa into an inline function.
Get floppy geometry directly from the drives.
Don't expose FDCtrl.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Other geometry guessing functions already reside in block.c.
Remove some unused or debugging only fields.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Now the only user of mainstone.h is mainstone.c file. Merge header
into board file.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
Simplify IRQ handling to stop setting an input irq pin. As a win, also get
correct IRQ status after save/load cycle.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
TPR blocks all interrupts in a priority class, so simple "less or
equal" check is not enough.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If kvmclock is used, which implies the kernel supports it, register a
kvmclock device with the sysbus. Its main purpose is to save and restore
the kernel state on migration, but this will also allow to visualize it
one day.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
CC: Glauber Costa <glommer@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
In order to use log_start/log_stop with Xen as well in the vga code,
this two operations have been put in CPUPhysMemoryClient.
The two new functions cpu_physical_log_start,cpu_physical_log_stop are
used in hw/vga.c and replace the kvm_log_start/stop. With this, vga does
no longer depends on kvm header.
[ Jan: rebasing and style fixlets ]
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Define and use dedicated constants for vm_stop reasons, they actually
have nothing to do with the EXCP_* defines used so far. At this chance,
specify more detailed reasons so that VM state change handlers can
evaluate them.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
1) Move GPIO-related functionality to qdev. Now one can use directly
qdev_get_gpio_in()/qdev_connect_gpio_out() on max7310 devices.
2) Make reset to be called through qdev.reset callback.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
The host part of a block device can be deleted with in progress
block migration.
To fix this, add a reference count to DriveInfo, freeing resources
on last reference.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Different AHCI controllers have a different number of ports, so the core
shouldn't care about the amount of ports available.
This patch makes the number of ports available to the AHCI core runtime
configurable, allowing us to have multiple different AHCI implementations
with different amounts of ports.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The ahci code was missing its soft reset functionality. This wasn't really an
issue for Linux guests, but Windows gets confused when the controller doesn't
reset when it tells it so.
Using this patch I can now successfully boot Windows 7 from AHCI using AHCI
enabled SeaBIOS.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The drive sends a d2h init fis on initialization. Usually, the guest doesn't
receive fises yet at that point though, so the delivery is deferred.
Let's reflect that by sending the init fis on fis receive enablement.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sebastian's patch already did a pretty good job at splitting up ICH-9
AHCI code and the AHCI core. We need some more though. Copyright was missing,
the lspci dump belongs to ICH-9, we don't need the AHCI core to have its
own qdev device duplicate.
So let's split them a bit more in this patch, making things easier to
read an understand.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Due to popular request, this patch adds a license header to ahci.h
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There are multiple ahci devices out there. The currently implemented ich-9
is only one of the many. So let's split that one out into a separate file
to stress the difference.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Fix a few style issues and convert magic numbers into prober symbolic
constants, also fixing the wrong but unused IOAPIC_DM_SIPI value.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
qemu-kvm carries the IOAPIC base address in its v2 vmstate. We only
support the default base address so far, and saving even that in the
device state was rejected.
Add a padding field to be able to read qemu-kvm's old state, but
increase our version to 3, indicating that we are not saving a valid
address. This also gives downstream the chance to change to stop
evaluating the base_address and move to v3 as well.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This is a guest modifiable state that must be saved/restored properly.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add the missing EOI broadcast from local APIC to the IOAPICs on
completion of level-triggered IRQs. This ensures that a still asserted
IRQ source properly re-triggers an APIC IRQ.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This can happen if a port gets unplugged before guest has chance to
initialise vqs.
Reported-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When MSI is off, each interrupt needs to be bounced through the io
thread when it's set/cleared, so vhost-net causes more context switches and
higher CPU utilization than userspace virtio which handles networking in
the same thread.
We'll need to fix this by adding level irq support in kvm irqfd,
for now disable vhost-net in these configurations.
Added a vhostforce flag to force vhost-net back on.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The Ubuntu 10.10 gcc for ARM complains that we might be overrunning
the cpu_irqs[][] array: silence this by correcting the bounds on the
loop. (In fact we would not have overrun the array because bit
MAX_PILS in pil_pending and irl_out will always be 0.)
Also add a comment about why the loop's lower bound is OK.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The "leon3_cache_control_int" (op_helper.c) function is called within leon3.c
which leads to segfault error with the global "env".
Now cache control is a CPU feature and everything is handled in op_helper.c.
Signed-off-by: Fabien Chouteau <chouteau@adacore.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Watch this:
(qemu) drive_add 0 if=none
(qemu) info block
none0: type=hd removable=0 [not inserted]
(qemu) drive_del none0
Segmentation fault (core dumped)
add_init_drive() is confused about drive_init()'s failure modes, and
cleans up when it shouldn't. This leaves the DriveInfo with member
opts dangling. drive_del attempts to free it, and dies.
drive_init() behaves as follows:
* If it created a drive with media, it returns its DriveInfo.
* If it created a drive without media, it clears *fatal_error and
returns NULL.
* If it couldn't create a drive, it sets *fatal_error and returns
NULL.
Of its three callers:
* drive_init_func() is correct.
* usb_msd_init() assumes drive_init() failed when it returns NULL.
This is correct only because it always passes option "file", and
"drive without media" can't happen then.
* add_init_drive() assumes drive_init() failed when it returns NULL.
This is incorrect.
Clean up drive_init() to return NULL on failure and only on failure.
Drop its parameter fatal_error.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Before, type & index were hidden in printf-like fmt, ... parameters,
which get expanded into an option string. Rather inconvenient for
uses later in this series.
New IF_DEFAULT to ask for the machine's default interface. Before,
that was done by having no option "if" in the option string.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Before commit 622b520f, index=12 meant bus=1,unit=5.
Since the commit, it means bus=0,unit=12. The drive is created, but
not the guest device. That's because the controllers we use with
if=scsi drives (lsi53c895a and esp) support only 7 units, and
scsi_bus_legacy_handle_cmdline() ignores drives with unit numbers
exceeding that limit.
Changing the mapping of index to bus, unit is a regression. Breaking
-drive invocations that used to work just makes it worse.
Revert the part of commit 622b520f that causes this, and clean up
some.
Note that the fix only affects if=scsi. You can still put more than 7
units on a SCSI bus with -device & friends.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
qdev_init_bdrv() doesn't belong into qdev.c; it's about drives, not
qdevs. Rename to drive_get_next, move to blockdev.c, drop the bogus
DeviceState argument, and return DriveInfo instead of
BlockDriverState.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
drive_init() picks the first free bus and unit number, unless the user
specifies them.
This isn't a good fit for the drive_add monitor command, because there
we specify the controller by PCI address instead of using bus number
set by drive_init().
scsi_hot_add() takes care to replace the unit number set by
drive_init() by the real one, but it neglects to replace the bus
number. Thus, bus/unit in DriveInfo may be bogus. Affects
drive_get() and drive_get_max_bus(). I'm not aware of anything bad
happening because of that; looks like by the time we're hot-plugging,
the two functions aren't used anymore. Fix it anyway.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The len and is_write arguments to cpu_physical_memory_unmap() were
swapped. This patch changes calls to use the correct argument ordering.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Raise a config change interrupt when the size changed. This allows
virtio-blk guest drivers to read-read the information from the
config space once it got the config chaged interrupt.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Extend the change_cb callback with a reason argument, and use it
to tell drivers about size changes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
r3480 added this check to account for the entry vector 0xfff00100 to be
available for CPUs that need it. Today however, the NIP is not yet
initialized at this point (zero), so the check always triggers.
Moreover, BIOS size check is already done previously, so this part can
be removed too.
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
For some unknown reason, the MIPS kernel briefly changes the RTC to
binary mode during boot, switch back to BCD mode and read the time. As
the registers are updated only every second, they may still be in the
old format when they are read.
This patch forces a register update immediately after a format change
(BCD/binary or 12/24H). This avoid long fsck during boot due to time
wrap.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
virtio-blk doesn't work on cross-endian configuration, as endianness is
not handled correctly.
This patch adds missing endianness conversions to make virtio-blk
working. Tested on the following configurations:
- i386 guest on x86_64 host
- ppc guest on x86_64 host
- i386 guest on mips host
- ppc guest on mips host
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
virtio-net used to work on cross-endianness configurations, but doesn't
anymore with recent guest kernels, as the new features don't handle
endianness correctly.
This patch fixes wrong conversion, and add missing ones to make
virtio-net working. Tested on the following configurations:
- i386 guest on x86_64 host
- ppc guest on x86_64 host
- i386 guest on mips host
- ppc guest on mips host
Cc: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Recent PowerPC kernel end up in kernel panic during boot in -nographic
mode. In this mode the second serial port is used as the udbg console,
and thus a few characters are sent on this port. This activates the
tx interrupt flag, and later choke the Linux kernel, as it was not
expecting such a flag to be set.
The problem here comes from the fact that contrary to most devices the
interrupt flags are only set if the interrupt is enabled. Quoting the
datasheet: "If the corresponding IE bit is not set, the IP for that
source of interrupt will never be set."
This patch fixes that by enabling the interrupt flag only when the
corresponding interrupt is enabled.
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
As noted by Markus Armbruster pxa2xx_gpio vmstate version bumped
because of a change in the or .ilevel / .olevel arrays are saved,
for convenience.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
Switch sl-nand emulation to use qdev and vmstate. Also drop ecc_get/_put
functions as sl-nand was the only user of that code.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
Convert SharpSL scoop device to qdev, remove lots of supporting code, as
lot of init and gpio related things can now be done automagically.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
This patch fixes typo in pcibus_get_dev_path().
Without this patch, the result of pcibus_get_dev_path() isn't unique.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PCI_BRIDGE_CTL_DISCARD_STATUS (bit 10 in bridge control register)
is W1C so we should not make it writeable, otherwise the assert(!(wmask
& w1cmask)) in pci_default_write_config() is hit
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: Isaku Yamahata <yamahata@valinux.co.jp>
Tested-by: Isaku Yamahata <yamahata@valinux.co.jp>
Leon3 is an open-source VHDL System-On-Chip, well known in space industry (more
information on http://www.gaisler.com).
Leon3 is made of multiple components available in the GrLib VHDL library.
Three devices are implemented: uart, timers and IRQ manager.
You can find code for these peripherals in the grlib_* files.
Signed-off-by: Fabien Chouteau <chouteau@adacore.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This device exposes one parameter:
- chardev (ptr) : Pointer to a qemu character device
Emulation of GrLib devices is base on the GRLIB IP Core User's Manual:
http://www.gaisler.com/products/grlib/grip.pdf
Signed-off-by: Fabien Chouteau <chouteau@adacore.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This device exposes two parameters:
- set_pil_in (ptr) : A function to set the pil_in of the SPARC CPU
- set_pil_in_opaque (ptr) : Opaque argument of the set_pil_in function
Emulation of GrLib devices is base on the GRLIB IP Core User's Manual:
http://www.gaisler.com/products/grlib/grip.pdf
Signed-off-by: Fabien Chouteau <chouteau@adacore.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This device exposes three parameters:
- frequency (uint32) : The system frequency
- irq-line (uint32) : IRQ line number for the first timer
(others use irq-line + 1, irq-line + 2...)
- nr-timers (uint32) : Number of timers
Emulation of GrLib devices is base on the GRLIB IP Core User's Manual:
http://www.gaisler.com/products/grlib/grip.pdf
Signed-off-by: Fabien Chouteau <chouteau@adacore.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
USB Mass Storage Devices sometimes have the RMB (removable) bit set in
the SCSI INQUIRY response. Thumbdrives tend to have the bit set whereas
hard disks do not.
Operating systems differentiate between removable devices and fixed
devices. Under Linux, the anaconda installer looks for removable
devices. Under Windows, only fixed devices may have more than one
partition and AutoRun is also affected by the removable bit.
For these reasons, allow USB Mass Storage Devices to override the
removable bit:
qemu -usb
-drive if=none,file=test.img,cache=none,id=disk0
-device usb-storage,drive=disk0,removable=on
The default is off.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
scsi-disk devices may wish to override the removable bit. Add support
for a qdev property on SCSI devices. This is will be used by usb-msd.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Provide the "removable" qdev property bit to override the SCSI INQUIRY
removable (RMB) bit for non-CDROM devices. This will be used by USB
Mass Storage Devices, which sometimes have this guest-visible bit set
and sometimes do not. They therefore requires a means for user
configuration.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Avoid this warning from OpenBSD linker:
LINK i386-softmmu/qemu
../usb-bus.o(.text+0x27c): In function `usb_get_fw_dev_path':
/src/qemu/hw/usb-bus.c:294: warning: sprintf() is often misused,
please use snprintf()
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Yes, seriously. There is no migration support at all for usb devices.
They loose state, especially the device address, and stop responding
because of that. Oops.
Luckily there is so much broken usb hardware out there that the guest
usually just kicks the device hard (via port reset and
reinitialization), then continues without a hitch. So we got away with
that in a surprising high number of cases.
The arrival of remote wakeup (which enables autosuspend support) changes
that picture though. The usb devices also forget that it they are
supposed to wakeup, so they don't do that. The host also doesn't notice
the device stopped working in case it suspended the device and thus
expects it waking up instead of polling it. Result is that your mouse
is dead.
Lets start fixing that. Add a vmstate struct for USBDevice.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch moves the 'head' and 'n' fields from USBMouseState and
USBKeyboardState to the common USBHIDState struct.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch adds a event queue to the usb keyboard. This makes sure the
guest will see all key events even if they come in bursts. With this
patch applied sending Ctrl-Alt-Del using vncviewer's F8 menu works.
Also with autosuspend enabled the first keypress on a suspended keyboard
takes a little longer to be delivered to the guest because the usb bus
must be resumed first. Without event queue this easily gets lost.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The polling nature of the USB HID device makes it very hard to double
click or drag while on a high-latency VNC connection. This patch,
based on work done in the Xen qemu-dm tree by Ian Jackson, fixes this
bug by adding an event queue to the device. The event queue associates
each movement with the correct button state, and remembers all button
presses and releases as well.
Signed-off-by: Ian Jackson <ian.jackson@eu.citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffman <kraxel@redhat.com>
With bm == NULL, other code in the same function would crash.
This bug was reported by cppcheck:
hw/ide/pci.c:280: error: Possible null pointer dereference: bm
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Live migration from and to spice 0.4 qxl devices isn't going to work.
Rip out the bits which attempt to support that. Zap the subsection
logic which is obsolete now. Bumb the version to make a clean cut.
This should obviously go in before 0.14 is released.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
PCIDevice::rom_file is leaked.
PCIDevice::rom_file is allocated in pci_qdev_init(), but not freed anywhere.
free it in qemu_unregister_device().
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Merge ide_dma_submit_check into it's only caller. Also use tail recursion
using a goto instead of a real recursion - this avoid overflowing the
stack in the pathological situation of an recurring error that is ignored.
We'll still be busy looping in ide_dma_cb, but at least won't eat up
all stack space after this.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Currenly the code only resets the io_buffer_index field for reads,
but the code seems to expect this for all types of I/O. I guess
we simply don't hit large enough transfers that would require this
often enough.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Factor the DMA I/O path that is duplicated between read and write
commands, into common helpers using the s->is_read flag added for
the macio ATA controller.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The upper memory size field should exclude the first MB of RAM.
Signed-off-by: Kevin Wolf <mail@kevin-wolf.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Due to signed/unsigned comparison, the dirty bits are never reset, and
the screen redrawn each time. Fix that by only using ram_addr_t types,
and looking for page_min != addr_max instead.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
isa_mem_base is computed from registers during reset, but due to QEMU
limitations some devices (e.g. VGA card) need to know it earlier when
they are registered.
Workaround this by setting the value during registration instead of
reset.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The PL190 implementation keeps the default vector address
in vect_addr[16], but we weren't using this for writes to
the DEFVECTADDR register. As a result of this fix the
default_addr structure member is unused and we can delete it.
Reported-by: Himanshu Chauhan <hschauhan@nulltrace.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
use qemu_malloc() instead of direct use of malloc().
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
deassert intx on device reset.
So far pci_device_reset() is used for system reset.
In that case, interrupt controller is reset at the same time so that
all irq is are deasserted.
But now pci bus reset/flr is supported, and in that case irq needs to be
disabled explicitly.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Recently PXA2xx lcd have stopped to be updated incrementally (picture
frozen). This patch fixes that by passing non min/max x/y, but rather
(correctly) x/y and w/h.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
vmstate_pxa2xx_i2c incorrectly recursed to itself instead of going
to store slave device. Fix that stop stop qemu from segfaulting
during savevm for pxa2xx-based devices.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Second instance of scoop contains registers shifted to 0x40 from the start
of the page. Instead of messing with register mapping, just limit register
address to 0x00..0x3f.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
