The swim chip provides an implementation of both Apple's IWM and ISM floppy disk
controllers. Split the existing implementation into separate register banks for
each controller, whilst also switching the IWM registers from 16-bit to 8-bit
as implemented in real hardware.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-ID: <20231004083806.757242-13-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This determines whether the Apple Sound Chip (ASC) is set to enhanced mode
(default) or to original mode. The real Q800 hardware used an EASC chip however
a lot of older software only works with the older ASC chip.
Adding this as a machine parameter allows QEMU to be used as an developer aid
for testing and migrating code from ASC to EASC.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-ID: <20231004083806.757242-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The Quadra 800 has the enhanced ASC (EASC) audio chip which supports both the
legacy IRQ routing through VIA2 and also "A/UX" mode routing direct to the
CPU.
Co-developed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20231004083806.757242-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
MacOS (un)helpfully leaves the FIFO engine running even when all the samples have
been written to the hardware, and expects the FIFO status flags and IRQ to be
updated continuously.
There is an additional problem in that not all audio backends guarantee an
all-zero output when there is no FIFO data available, in particular the Windows
dsound backend which re-uses its internal circular buffer causing the last played
sound to loop indefinitely.
Whilst this is effectively a bug in the Windows dsound backend, work around it
for now using a simple heuristic: if the FIFO remains empty for half a cycle
(~23ms) then continuously fill the generated buffer with empty silence.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-ID: <20231004083806.757242-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The Apple Sound Chip was primarily used by the Macintosh II to generate sound
in hardware which was previously handled by the toolbox ROM with software
interrupts.
Implement both the standard ASC and also the enhanced ASC (EASC) functionality
which is used in the Quadra 800.
Note that whilst real ASC hardware uses AUDIO_FORMAT_S8, this implementation uses
AUDIO_FORMAT_U8 instead because AUDIO_FORMAT_S8 is rarely used and not supported
by some audio backends like PulseAudio and DirectSound when played directly with
-audiodev out.mixing-engine=off.
Co-developed-by: Laurent Vivier <laurent@vivier.eu>
Co-developed-by: Volker Rümelin <vr_qemu@t-online.de>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20231004083806.757242-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
MacOS attempts a series of writes and reads over the entire RAM area in order
to determine the amount of RAM within the machine. Allow accesses to the
entire RAM area ignoring writes and always reading zero for areas where there
is no physical RAM installed to allow MacOS to detect the memory size without
faulting.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-ID: <20231004083806.757242-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
It is needed because it defines the BIOSConfig area.
Co-developed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-ID: <20231004083806.757242-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
MacOS reads this address to identify the hardware.
This is a basic implementation returning the ID of Quadra 800.
Details:
http://mess.redump.net/mess/driver_info/mac_technical_notes
"There are 3 ID schemes [...]
The third and most scalable is a machine ID register at 0x5ffffffc.
The top word must be 0xa55a to be valid. Then bits 15-11 are 0 for
consumer Macs, 1 for portables, 2 for high-end 68k, and 3 for high-end
PowerPC. Bit 10 is 1 if additional ID bits appear elsewhere (e.g. in VIA1).
The rest of the bits are a per-model identifier.
Model Lower 16 bits of ID
...
Quadra/Centris 610/650/800 0x2BAD"
Co-developed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20231004083806.757242-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The djMEMC controller is used to store information related to the physical memory
configuration.
Co-developed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20231004083806.757242-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
vdpa:
shadow vq vlan support
net migration with cvq
cxl:
support emulating 4 HDM decoders
serial number extended capability
virtio:
hared dma-buf
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmUd4/YPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpyM8H/02cRbJcQOjYt7j68zPW6GaDXxBI/UmdWDyG
15LZZbGNOPjyjNd3Vz1M7stQ5rhoKcgo/RdI+0E60a78svgW5JvpXoXR3pksc3Dx
v28B/akXwHUErYFSZQ+2VHNc8OhCd0v2ehxZxbwPEAYIOAj3hcCIVoPGXTnKJmAJ
imr5hjH0wZUc0+xdsmn8Vfdv5NTzpwfVObbGiMZejeJsaoh0y6Rt8RANBMY67KQD
S7/HPlVuDYf/y43t4ZEHNYuV9RaCdZZYlLWwV1scdKaYcofgmtJOKbOdCjHRXgj+
004Afb3rggIoCfnCzOFzhGx+MLDtLjvEn2N4oLEWCLi+k/3huaA=
=GAvH
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pci: features, cleanups
vdpa:
shadow vq vlan support
net migration with cvq
cxl:
support emulating 4 HDM decoders
serial number extended capability
virtio:
hared dma-buf
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (53 commits)
libvhost-user: handle shared_object msg
vhost-user: add shared_object msg
hw/display: introduce virtio-dmabuf
util/uuid: add a hash function
virtio: remove unused next argument from virtqueue_split_read_next_desc()
virtio: remove unnecessary thread fence while reading next descriptor
virtio: use shadow_avail_idx while checking number of heads
libvhost-user.c: add assertion to vu_message_read_default
pcie_sriov: unregister_vfs(): fix error path
hw/i386/pc: improve physical address space bound check for 32-bit x86 systems
amd_iommu: Fix APIC address check
vdpa net: follow VirtIO initialization properly at cvq isolation probing
vdpa net: stop probing if cannot set features
vdpa net: fix error message setting virtio status
hw/pci-bridge/cxl-upstream: Add serial number extended capability support
hw/cxl: Support 4 HDM decoders at all levels of topology
hw/cxl: Fix and use same calculation for HDM decoder block size everywhere
hw/cxl: Add utility functions decoder interleave ways and target count.
hw/cxl: Push cxl_decoder_count_enc() and cxl_decode_ig() into .c
vdpa net: zero vhost_vdpa iova_tree pointer at cleanup
...
Conflicts:
hw/core/machine.c
Context conflict with commit 314e0a84cd ("hw/core: remove needless
includes") because it removed an adjacent #include.
Add three new vhost-user protocol
`VHOST_USER_BACKEND_SHARED_OBJECT_* messages`.
These new messages are sent from vhost-user
back-ends to interact with the virtio-dmabuf
table in order to add or remove themselves as
virtio exporters, or lookup for virtio dma-buf
shared objects.
The action taken in the front-end depends
on the type stored in the virtio shared
object hash table.
When the table holds a pointer to a vhost
backend for a given UUID, the front-end sends
a VHOST_USER_GET_SHARED_OBJECT to the
backend holding the shared object.
The messages can only be sent after successfully
negotiating a new VHOST_USER_PROTOCOL_F_SHARED_OBJECT
vhost-user protocol feature bit.
Finally, refactor code to send response message so
that all common parts both for the common REPLY_ACK
case, and other data responses, can call it and
avoid code repetition.
Signed-off-by: Albert Esteve <aesteve@redhat.com>
Message-Id: <20231002065706.94707-4-aesteve@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This API manages objects (in this iteration,
dmabuf fds) that can be shared along different
virtio devices, associated to a UUID.
The API allows the different devices to add,
remove and/or retrieve the objects by simply
invoking the public functions that reside in the
virtio-dmabuf file.
For vhost backends, the API stores the pointer
to the backend holding the object.
Suggested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Albert Esteve <aesteve@redhat.com>
Message-Id: <20231002065706.94707-3-aesteve@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
32-bit x86 systems do not have a reserved memory for hole64. On those 32-bit
systems without PSE36 or PAE CPU features, hotplugging memory devices are not
supported by QEMU as QEMU always places hotplugged memory above 4 GiB boundary
which is beyond the physical address space of the processor. Linux guests also
does not support memory hotplug on those systems. Please see Linux
kernel commit b59d02ed08690 ("mm/memory_hotplug: disable the functionality
for 32b") for more details.
Therefore, the maximum limit of the guest physical address in the absence of
additional memory devices effectively coincides with the end of
"above 4G memory space" region for 32-bit x86 without PAE/PSE36. When users
configure additional memory devices, after properly accounting for the
additional device memory region to find the maximum value of the guest
physical address, the address will be outside the range of the processor's
physical address space.
This change adds improvements to take above into consideration.
For example, previously this was allowed:
$ ./qemu-system-x86_64 -cpu pentium -m size=10G
With this change now it is no longer allowed:
$ ./qemu-system-x86_64 -cpu pentium -m size=10G
qemu-system-x86_64: Address space limit 0xffffffff < 0x2bfffffff phys-bits too low (32)
However, the following are allowed since on both cases physical address
space of the processor is 36 bits:
$ ./qemu-system-x86_64 -cpu pentium2 -m size=10G
$ ./qemu-system-x86_64 -cpu pentium,pse36=on -m size=10G
For 32-bit, without PAE/PSE36, hotplugging additional memory is no longer allowed.
$ ./qemu-system-i386 -m size=1G,maxmem=3G,slots=2
qemu-system-i386: Address space limit 0xffffffff < 0x1ffffffff phys-bits too low (32)
$ ./qemu-system-i386 -machine q35 -m size=1G,maxmem=3G,slots=2
qemu-system-i386: Address space limit 0xffffffff < 0x1ffffffff phys-bits too low (32)
A new compatibility flag is introduced to make sure pc_max_used_gpa() keeps
returning the old value for machines 8.1 and older.
Therefore, the above is still allowed for older machine types in order to support
compatibility. Hence, the following still works:
$ ./qemu-system-i386 -machine pc-i440fx-8.1 -m size=1G,maxmem=3G,slots=2
$ ./qemu-system-i386 -machine pc-q35-8.1 -m size=1G,maxmem=3G,slots=2
Further, following is also allowed as with PSE36, the processor has 36-bit
address space:
$ ./qemu-system-i386 -cpu 486,pse36=on -m size=1G,maxmem=3G,slots=2
After calling CPUID with EAX=0x80000001, all AMD64 compliant processors
have the longmode-capable-bit turned on in the extended feature flags (bit 29)
in EDX. The absence of CPUID longmode can be used to differentiate between
32-bit and 64-bit processors and is the recommended approach. QEMU takes this
approach elsewhere (for example, please see x86_cpu_realizefn()), With
this change, pc_max_used_gpa() also uses the same method to detect 32-bit
processors.
Unit tests are modified to not run 32-bit x86 tests that use memory hotplug.
Suggested-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Ani Sinha <anisinha@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230922160413.165702-1-anisinha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Support these decoders in CXL host bridges (pxb-cxl), CXL Switch USP
and CXL Type 3 end points.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230913132523.29780-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In order to avoid having the size of the per HDM decoder register block
repeated in lots of places, create the register definitions for HDM
decoder 1 and use the offset between the first registers in HDM decoder 0 and
HDM decoder 1 to establish the offset.
Calculate in each function as this is more obvious and leads to shorter
line lengths than a single #define which would need a long name
to be specific enough.
Note that the code currently only supports one decoder, so the bugs this
fixes don't actually affect anything.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230913132523.29780-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As an encoded version of these key configuration parameters is available
in a register, provide functions to extract it again so as to avoid
the need for duplicating the storage.
Whilst here update the _enc() function to include additional values
as defined in the CXL 3.0 specification. Whilst they are not
currently used in the emulation, they may be in future and it is
easier to compare with the specification if all values are covered.
Add a spec reference for cxl_interleave_ways_enc() for consistency
with the target count equivalent (and because it's nice to know where
the magic numbers come from).
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230913132523.29780-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is no strong justification for keeping these in the header
so push them down into the associated cxl-component-utils.c file.
Suggested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230913132523.29780-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now that TYPE_ACPI_GED_X86 doesn't assign AcpiDeviceIfClass::madt_cpu any more
it is the same as TYPE_ACPI_GED.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230908084234.17642-6-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The "hw/boards.h" is unused since the previous commit. Since its removal
requires include fixes in various unrelated files to keep the code compiling it
has been split in a dedicated commit.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230908084234.17642-5-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This virtual method was always set to the x86-specific pc_madt_cpu_entry(),
even in piix4 which is also used in MIPS. The previous changes use
pc_madt_cpu_entry() otherwise, so madt_cpu can be dropped.
Since pc_madt_cpu_entry() is now only used in x86-specific code, the stub
in hw/acpi/acpi-x86-stub can be removed as well.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230908084234.17642-4-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
build_cpus_aml() is architecture independent but needs to create architecture-
specific CPU AML. So far this was achieved by using a virtual method from
TYPE_ACPI_DEVICE_IF. However, build_cpus_aml() would resolve this interface from
global (!) state. This makes it quite incomprehensible where this interface
comes from (TYPE_PIIX4_PM?, TYPE_ICH9_LPC_DEVICE?, TYPE_ACPI_GED_X86?) an can
lead to crashes when the generic code is ported to new architectures.
So far, build_cpus_aml() is only called in architecture-specific code -- and
only in x86. We can therefore simply pass pc_madt_cpu_entry() as callback to
build_cpus_aml(). This is the same callback that would be used through
TYPE_ACPI_DEVICE_IF.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230908084234.17642-3-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move the definition of VhostUserProtocolFeature to
include/hw/virtio/vhost-user.h.
Remove previous definitions in hw/scsi/vhost-user-scsi.c,
hw/virtio/vhost-user.c, and hw/virtio/virtio-qmp.c.
Previously there were 3 separate definitions of this over 3 different
files. Now only 1 definition of this will be present for these 3 files.
Signed-off-by: Jonah Palmer <jonah.palmer@oracle.com>
Reviewed-by: Emmanouil Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-Id: <20230926224107.2951144-4-jonah.palmer@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The vhost-vdpa net backend needs to enable vrings in a different order
than default, so export it.
No functional change intended except for tracing, that now includes the
(virtio) index being enabled and the return value of the ioctl.
Still ignoring return value of this function if called from
vhost_vdpa_dev_start, as reorganize calling code around it is out of
the scope of this series.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20230822085330.3978829-3-eperezma@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost-vdpa shadowed CVQ needs to know the maximum number of
vlans supported by the virtio-net device, so QEMU can restore
the VLAN state in a migration.
Co-developed-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Message-Id: <ca03403319c6405ea7c400836a572255bbc9ceba.1690106284.git.yin31149@gmail.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To use the generic device the user will need to provide the config
region size via the command line. We also add a notifier so the guest
can be pinged if the remote daemon updates the config.
With these changes:
-device vhost-user-device-pci,virtio-id=41,num_vqs=2,config_size=8
is equivalent to:
-device vhost-user-gpio-pci
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230710153522.3469097-11-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In theory we shouldn't need to repeat so much boilerplate to support
vhost-user backends. This provides a generic vhost-user-base QOM
object and a derived vhost-user-device for which the user needs to
provide the few bits of information that aren't currently provided by
the vhost-user protocol. This should provide a baseline implementation
from which the other vhost-user stub can specialise.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230710153522.3469097-8-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
current code sets PCI_SEC_LATENCY_TIMER to RW, but for
pcie to pcie bridges it must be RO 0 according to
pci express spec which says:
This register does not apply to PCI Express. It must be read-only
and hardwired to 00h. For PCI Express to PCI/PCI-X Bridges, refer to the
[PCIe-to-PCI-PCI-X-Bridge] for requirements for this register.
also, fix typo in comment where it's made writeable - this typo
is likely what prevented us noticing we violate this requirement
in the 1st place.
Reported-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Message-Id: <de9d05366a70172e1789d10591dbe59e39c3849c.1693432039.git.mst@redhat.com>
Tested-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Minimize the displacement to can_do_io, since it may
be touched at the start of each TranslationBlock.
It fits into other padding within the substructure.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Retain the separate structure to emphasize its importance.
Enforce CPUArchState always follows CPUState without padding.
Reviewed-by: Anton Johansson <anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Accept that we will consume space in CPUState for CONFIG_USER_ONLY,
since we cannot test CONFIG_SOFTMMU within hw/core/cpu.h.
Reviewed-by: Anton Johansson <anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The AccelCPUClass::cpu_realizefn handler is meant for target
specific code, rename it using '_target_' to emphasis it.
Suggested-by: Claudio Fontana <cfontana@suse.de>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20231003123026.99229-3-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
* fix for KVM on Apple M2
* introduce machine property "audiodev"
* ui/vnc: Require audiodev= to enable audio
* audio: remove QEMU_AUDIO_* and -audio-help support
* audio: forbid using default audiodev backend with -audiodev and -nodefaults
* remove compatibility code for old machine types
* make-release: do not ship dtc sources
* build system cleanups
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmUb0QgUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroOpnAf9EFXfGkXpqQ5Q8ZbVlVc5GQKofMHW
OZwamTBlp/c07+QcQiMxwLhIW0iyDhrfdCjoFSUaTA8O10FM1YrFv4SkUryYb9B3
bmoTl4NeLvmkxpC47GEeaaBfjyM0G/9Ip9Zsuqx3u+gSzwTbkEstA2u7gcsN0tL9
VlhMSiV82uHhRC/DJYLxr+8bRYSIm1AeuI8K/O1yags85Kztf3UiQUhePIKLznMH
BdORjD+i46xM1dE8ifpdsunm462cDWz/faAnIH0YVKBlshnQHXKTO+GDA/Fbfl51
wFfupZXo93wwgawS7elAUzI+gwaKCPRHA8NDcukeO91hTzk6i14y04u5SQ==
=nv64
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://gitlab.com/bonzini/qemu into staging
* fix from optionrom build
* fix for KVM on Apple M2
* introduce machine property "audiodev"
* ui/vnc: Require audiodev= to enable audio
* audio: remove QEMU_AUDIO_* and -audio-help support
* audio: forbid using default audiodev backend with -audiodev and -nodefaults
* remove compatibility code for old machine types
* make-release: do not ship dtc sources
* build system cleanups
# -----BEGIN PGP SIGNATURE-----
#
# iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmUb0QgUHHBib256aW5p
# QHJlZGhhdC5jb20ACgkQv/vSX3jHroOpnAf9EFXfGkXpqQ5Q8ZbVlVc5GQKofMHW
# OZwamTBlp/c07+QcQiMxwLhIW0iyDhrfdCjoFSUaTA8O10FM1YrFv4SkUryYb9B3
# bmoTl4NeLvmkxpC47GEeaaBfjyM0G/9Ip9Zsuqx3u+gSzwTbkEstA2u7gcsN0tL9
# VlhMSiV82uHhRC/DJYLxr+8bRYSIm1AeuI8K/O1yags85Kztf3UiQUhePIKLznMH
# BdORjD+i46xM1dE8ifpdsunm462cDWz/faAnIH0YVKBlshnQHXKTO+GDA/Fbfl51
# wFfupZXo93wwgawS7elAUzI+gwaKCPRHA8NDcukeO91hTzk6i14y04u5SQ==
# =nv64
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 03 Oct 2023 04:30:00 EDT
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* tag 'for-upstream' of https://gitlab.com/bonzini/qemu: (24 commits)
audio: forbid default audiodev backend with -nodefaults
audio: propagate Error * out of audio_init
vt82c686 machines: Support machine-default audiodev with fallback
hw/ppc: Support machine-default audiodev with fallback
hw/arm: Support machine-default audiodev with fallback
Introduce machine property "audiodev"
audio: remove QEMU_AUDIO_* and -audio-help support
audio: simplify flow in audio_init
audio: commonize voice initialization
audio: return Error ** from audio_state_by_name
audio: allow returning an error from the driver init
audio: Require AudioState in AUD_add_capture
ui/vnc: Require audiodev= to enable audio
crypto: only include tls-cipher-suites in emulators
scsi-disk: ensure that FORMAT UNIT commands are terminated
esp: restrict non-DMA transfer length to that of available data
esp: use correct type for esp_dma_enable() in sysbus_esp_gpio_demux()
Makefile: build plugins before running TCG tests
meson: clean up static_library keyword arguments
make-release: do not ship dtc sources
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Many machine types have default audio devices with no way to set the underlying
audiodev. Instead of adding an option for each and every one of them, this new
property can be used as a default during machine initialisation when creating
such devices.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
[Make the property optional, instead of including it in all machines. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
this fixes numerous warnings of this type :
In file included from ../hw/ppc/spapr_pci.c:43:
../hw/ppc/spapr_pci.c: In function ‘spapr_dt_phb’:
../include/hw/ppc/fdt.h:18:13: warning: declaration of ‘ret’ shadows a previous local [-Wshadow=compatible-local]
18 | int ret = (exp); \
| ^~~
../hw/ppc/spapr_pci.c:2355:5: note: in expansion of macro ‘_FDT’
2355 | _FDT(bus_off = fdt_add_subnode(fdt, 0, phb->dtbusname));
| ^~~~
../hw/ppc/spapr_pci.c:2311:24: note: shadowed declaration is here
2311 | int bus_off, i, j, ret;
| ^~~
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <20230918145850.241074-2-clg@kaod.org>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
According to cxl_interleave_ways_enc(), fw->num_targets is allowed to be up
to 16. This also corresponds to CXL r3.0 spec. So, the fw->target_hbs[]
array is iterated from 0 to 15. But it is statically declared of length 8.
Thus, out of bound array access may occur.
Fixes: c28db9e000 ("hw/pci-bridge: Make PCIe and CXL PXB Devices inherit from TYPE_PXB_DEV")
Signed-off-by: Dmitry Frolov <frolov@swemel.ru>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Link: https://lore.kernel.org/r/20230913101055.754709-1-frolov@swemel.ru
Cc: qemu-stable@nongnu.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Replace the magic number 32 with CXL_RAS_ERR_HEADER_NUM for better code
readability and maintainability.
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
"Host Memory Backends" and "Memory devices" queue ("mem"):
- Support and document VM templating with R/O files using a new "rom"
parameter for memory-backend-file
- Some cleanups and fixes around NVDIMMs and R/O file handling for guest
RAM
- Optimize ioeventfd updates by skipping address spaces that are not
applicable
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEG9nKrXNcTDpGDfzKTd4Q9wD/g1oFAmUJdykRHGRhdmlkQHJl
ZGhhdC5jb20ACgkQTd4Q9wD/g1pf2w//akOUoYMuamySGjXtKLVyMKZkjIys+Ama
k2C0xzsWAHBP572ezwHi8uxf5j9kzAjsw6GxDZ7FAamD9MhiohkEvkecloBx6f/c
q3fVHblBNkG7v2urtf4+6PJtJvhzOST2SFXfWeYhO/vaA04AYCDgexv82JN3gA6B
OS8WyOX62b8wILPSY2GLZ8IqpE9XnOYZwzVBn6YB1yo7ZkYEfXO6cA8nykNuNcOE
vppqDo7uVIX6317FWj8ygxmzFfOaj0WT2MT2XFzEIDfg8BInQN8HC4mTn0hcVKMa
N1y+eZH733CQKT+uNBRZ5YOeljOi4d6gEEyvkkA/L7e5D3Qg9hIdvHb4uryCFSWX
Vt07OP1XLBwCZFobOC6sg+2gtTZJxxYK89e6ZzEd0454S24w5bnEteRAaCGOP0XL
ww9xYULqhtZs55UC4rvZHJwdUAk1fIY4VqynwkeQXegvz6BxedNeEkJiiEU0Tizx
N2VpsxAJ7H/LLSFeZoCRESo4azrH6U4n7S/eS1tkCniFqibfe2yIQCDoJVfb42ec
gfg/vThCrDwHkIHzkMmoV8NndA7Q7SIkyMfYeEEBeZMeg8JzYll4DJEw/jQCacxh
KRUa+AZvGlTJUq0mkvyOVfLki+iaehoIUuY1yvMrmdWijPO8n3YybmP9Ljhr8VdR
9MSYZe+I2v8=
=iraT
-----END PGP SIGNATURE-----
Merge tag 'mem-2023-09-19' of https://github.com/davidhildenbrand/qemu into staging
Hi,
"Host Memory Backends" and "Memory devices" queue ("mem"):
- Support and document VM templating with R/O files using a new "rom"
parameter for memory-backend-file
- Some cleanups and fixes around NVDIMMs and R/O file handling for guest
RAM
- Optimize ioeventfd updates by skipping address spaces that are not
applicable
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEG9nKrXNcTDpGDfzKTd4Q9wD/g1oFAmUJdykRHGRhdmlkQHJl
# ZGhhdC5jb20ACgkQTd4Q9wD/g1pf2w//akOUoYMuamySGjXtKLVyMKZkjIys+Ama
# k2C0xzsWAHBP572ezwHi8uxf5j9kzAjsw6GxDZ7FAamD9MhiohkEvkecloBx6f/c
# q3fVHblBNkG7v2urtf4+6PJtJvhzOST2SFXfWeYhO/vaA04AYCDgexv82JN3gA6B
# OS8WyOX62b8wILPSY2GLZ8IqpE9XnOYZwzVBn6YB1yo7ZkYEfXO6cA8nykNuNcOE
# vppqDo7uVIX6317FWj8ygxmzFfOaj0WT2MT2XFzEIDfg8BInQN8HC4mTn0hcVKMa
# N1y+eZH733CQKT+uNBRZ5YOeljOi4d6gEEyvkkA/L7e5D3Qg9hIdvHb4uryCFSWX
# Vt07OP1XLBwCZFobOC6sg+2gtTZJxxYK89e6ZzEd0454S24w5bnEteRAaCGOP0XL
# ww9xYULqhtZs55UC4rvZHJwdUAk1fIY4VqynwkeQXegvz6BxedNeEkJiiEU0Tizx
# N2VpsxAJ7H/LLSFeZoCRESo4azrH6U4n7S/eS1tkCniFqibfe2yIQCDoJVfb42ec
# gfg/vThCrDwHkIHzkMmoV8NndA7Q7SIkyMfYeEEBeZMeg8JzYll4DJEw/jQCacxh
# KRUa+AZvGlTJUq0mkvyOVfLki+iaehoIUuY1yvMrmdWijPO8n3YybmP9Ljhr8VdR
# 9MSYZe+I2v8=
# =iraT
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 19 Sep 2023 06:25:45 EDT
# gpg: using RSA key 1BD9CAAD735C4C3A460DFCCA4DDE10F700FF835A
# gpg: issuer "david@redhat.com"
# gpg: Good signature from "David Hildenbrand <david@redhat.com>" [unknown]
# gpg: aka "David Hildenbrand <davidhildenbrand@gmail.com>" [full]
# gpg: aka "David Hildenbrand <hildenbr@in.tum.de>" [unknown]
# gpg: WARNING: The key's User ID is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 1BD9 CAAD 735C 4C3A 460D FCCA 4DDE 10F7 00FF 835A
* tag 'mem-2023-09-19' of https://github.com/davidhildenbrand/qemu:
memory: avoid updating ioeventfds for some address_space
machine: Improve error message when using default RAM backend id
softmmu/physmem: Hint that "readonly=on,rom=off" exists when opening file R/W for private mapping fails
docs: Start documenting VM templating
docs: Don't mention "-mem-path" in multi-process.rst
softmmu/physmem: Never return directories from file_ram_open()
softmmu/physmem: Fail creation of new files in file_ram_open() with readonly=true
softmmu/physmem: Bail out early in ram_block_discard_range() with readonly files
softmmu/physmem: Remap with proper protection in qemu_ram_remap()
backends/hostmem-file: Add "rom" property to support VM templating with R/O files
softmmu/physmem: Distinguish between file access mode and mmap protection
nvdimm: Reject writing label data to ROM instead of crashing QEMU
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In this short queue we're making two important changes:
- Nicholas Piggin is now the qemu-ppc maintainer. Cédric Le Goater and
Daniel Barboza will act as backup during Nick's transition to this new
role.
- Support for NVIDIA V100 GPU with NVLink2 is dropped from qemu-ppc.
Linux removed the same support back in 5.13, we're following suit now.
A xive Coverity fix is also included.
-----BEGIN PGP SIGNATURE-----
iIwEABYKADQWIQQX6/+ZI9AYAK8oOBk82cqW3gMxZAUCZQhPnBYcZGFuaWVsaGI0
MTNAZ21haWwuY29tAAoJEDzZypbeAzFk5QUBAJJNnCtv/SPP6bQVNGMgtfI9sz2z
MEttDa7SINyLCiVxAP0Y9z8ZHEj6vhztTX0AAv2QubCKWIVbJZbPV5RWrHCEBQ==
=y3nh
-----END PGP SIGNATURE-----
Merge tag 'pull-ppc-20230918' of https://gitlab.com/danielhb/qemu into staging
ppc patch queue for 2023-09-18:
In this short queue we're making two important changes:
- Nicholas Piggin is now the qemu-ppc maintainer. Cédric Le Goater and
Daniel Barboza will act as backup during Nick's transition to this new
role.
- Support for NVIDIA V100 GPU with NVLink2 is dropped from qemu-ppc.
Linux removed the same support back in 5.13, we're following suit now.
A xive Coverity fix is also included.
# -----BEGIN PGP SIGNATURE-----
#
# iIwEABYKADQWIQQX6/+ZI9AYAK8oOBk82cqW3gMxZAUCZQhPnBYcZGFuaWVsaGI0
# MTNAZ21haWwuY29tAAoJEDzZypbeAzFk5QUBAJJNnCtv/SPP6bQVNGMgtfI9sz2z
# MEttDa7SINyLCiVxAP0Y9z8ZHEj6vhztTX0AAv2QubCKWIVbJZbPV5RWrHCEBQ==
# =y3nh
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 18 Sep 2023 09:24:44 EDT
# gpg: using EDDSA key 17EBFF9923D01800AF2838193CD9CA96DE033164
# gpg: issuer "danielhb413@gmail.com"
# gpg: Good signature from "Daniel Henrique Barboza <danielhb413@gmail.com>" [unknown]
# gpg: WARNING: The key's User ID is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 17EB FF99 23D0 1800 AF28 3819 3CD9 CA96 DE03 3164
* tag 'pull-ppc-20230918' of https://gitlab.com/danielhb/qemu:
spapr: Remove support for NVIDIA V100 GPU with NVLink2
ppc/xive: Fix uint32_t overflow
MAINTAINERS: Nick Piggin PPC maintainer, other PPC changes
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Currently, when using a true R/O NVDIMM (ROM memory backend) with a label
area, the VM can easily crash QEMU by trying to write to the label area,
because the ROM memory is mmap'ed without PROT_WRITE.
[root@vm-0 ~]# ndctl disable-region region0
disabled 1 region
[root@vm-0 ~]# ndctl zero-labels nmem0
-> QEMU segfaults
Let's remember whether we have a ROM memory backend and properly
reject the write request:
[root@vm-0 ~]# ndctl disable-region region0
disabled 1 region
[root@vm-0 ~]# ndctl zero-labels nmem0
zeroed 0 nmem
In comparison, on a system with a R/W NVDIMM:
[root@vm-0 ~]# ndctl disable-region region0
disabled 1 region
[root@vm-0 ~]# ndctl zero-labels nmem0
zeroed 1 nmem
For ACPI, just return "unsupported", like if no label exists. For spapr,
return "H_P2", similar to when no label area exists.
Could we rely on the "unarmed" property? Maybe, but it looks cleaner to
only disallow what certainly cannot work.
After all "unarmed=on" primarily means: cannot accept persistent writes. In
theory, there might be setups where devices with "unarmed=on" set could
be used to host non-persistent data (temporary files, system RAM, ...); for
example, in Linux, admins can overwrite the "readonly" setting and still
write to the device -- which will work as long as we're not using ROM.
Allowing writing label data in such configurations can make sense.
Message-ID: <20230906120503.359863-2-david@redhat.com>
Fixes: dbd730e859 ("nvdimm: check -object memory-backend-file, readonly=on option")
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
NVLink2 support was removed from the PPC PowerNV platform and VFIO in
Linux 5.13 with commits :
562d1e207d32 ("powerpc/powernv: remove the nvlink support")
b392a1989170 ("vfio/pci: remove vfio_pci_nvlink2")
This was 2.5 years ago. Do the same in QEMU with a revert of commit
ec132efaa8 ("spapr: Support NVIDIA V100 GPU with NVLink2"). Some
adjustements are required on the NUMA part.
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Message-ID: <20230918091717.149950-1-clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Now that we defer address space update and tlb_flush until
the next async_run_on_cpu, the plugin run at the end of the
instruction no longer has to contend with a flushed tlb.
Therefore, delete SavedIOTLB entirely.
Properly return false from tlb_plugin_lookup when we do
not have a tlb match.
Fixes a bug in which SavedIOTLB had stale data, because
there were multiple i/o accesses within a single insn.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
* Small downtime optimisation for VFIO migration
* P2P support for VFIO migration
* Introduction of a save_prepare() handler to fail VFIO migration
* Fix on DMA logging ranges calculation for OVMF enabling dynamic window
-----BEGIN PGP SIGNATURE-----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=44e0
-----END PGP SIGNATURE-----
Merge tag 'pull-vfio-20230911' of https://github.com/legoater/qemu into staging
vfio queue:
* Small downtime optimisation for VFIO migration
* P2P support for VFIO migration
* Introduction of a save_prepare() handler to fail VFIO migration
* Fix on DMA logging ranges calculation for OVMF enabling dynamic window
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmT+uZQACgkQUaNDx8/7
# 7KGFSw//UIqSet6MUxZZh/t7yfNFUTnxx6iPdChC3BphBaDDh99FCQrw5mPZ8ImF
# 4rz0cIwSaHXraugEsC42TDaGjEmcAmYD0Crz+pSpLU21nKtYyWtZy6+9kyYslMNF
# bUq0UwD0RGTP+ZZi6GBy1hM30y/JbNAGeC6uX8kyJRuK5Korfzoa/X5h+B2XfouW
# 78G1mARHq5eOkGy91+rAJowdjqtkpKrzkfCJu83330Bb035qAT/PEzGs5LxdfTla
# ORNqWHy3W+d8ZBicBQ5vwrk6D5JIZWma7vdXJRhs1wGO615cuyt1L8nWLFr8klW5
# MJl+wM7DZ6UlSODq7r839GtSuWAnQc2j7JKc+iqZuBBk1v9fGXv2tZmtuTGkG2hN
# nYXSQfuq1igu1nGVdxJv6WorDxsK9wzLNO2ckrOcKTT28RFl8oCDNSPPTKpwmfb5
# i5RrGreeXXqRXIw0VHhq5EqpROLjAFwE9tkJndO8765Ag154plxssaKTUWo5wm7/
# kjQVuRuhs5nnMXfL9ixLZkwD1aFn5fWAIaR0psH5vGD0fnB1Pba+Ux9ZzHvxp5D8
# Kg3H6dKlht6VXdQ/qb0Up1LXCGEa70QM6Th2iO924ydZkkmqrSj+CFwGHvBsINa4
# 89fYd77nbRbdwWurj3JIznJYVipau2PmfbjZ/jTed4RxjBQ+fPA=
# =44e0
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 11 Sep 2023 02:54:12 EDT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@redhat.com>" [unknown]
# gpg: aka "Cédric Le Goater <clg@kaod.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-vfio-20230911' of https://github.com/legoater/qemu:
vfio/common: Separate vfio-pci ranges
vfio/migration: Block VFIO migration with background snapshot
vfio/migration: Block VFIO migration with postcopy migration
migration: Add .save_prepare() handler to struct SaveVMHandlers
migration: Move more initializations to migrate_init()
vfio/migration: Fail adding device with enable-migration=on and existing blocker
migration: Add migration prefix to functions in target.c
vfio/migration: Allow migration of multiple P2P supporting devices
vfio/migration: Add P2P support for VFIO migration
vfio/migration: Refactor PRE_COPY and RUNNING state checks
qdev: Add qdev_add_vm_change_state_handler_full()
sysemu: Add prepare callback to struct VMChangeStateEntry
vfio/migration: Move from STOP_COPY to STOP in vfio_save_cleanup()
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move the PRE_COPY and RUNNING state checks to helper functions.
This is in preparation for adding P2P VFIO migration support, where
these helpers will also test for PRE_COPY_P2P and RUNNING_P2P states.
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: YangHang Liu <yanghliu@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Connect the Configuration Frame controller (CFRAME_REG) and the
Configuration Frame broadcast controller (CFRAME_BCAST_REG) to the
Versal machine.
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230831165701.2016397-9-francisco.iglesias@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
