%-softmmu.mak only keep boards and optional device
definitions in Kconfig mode.
Note that the Dino board uses a memory mapped 16550 UART and
therefore only CONFIG_SERIAL is needed, not CONFIG_SERIAL_ISA.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This makes it much easier if the users want to disable some of
the embedded machines for their builds.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Most of the dependencies are now directly selected by the SAM460EX
switch. We can drop CONFIG_VGA_CIRRUS since this device is already
selected automatically when CONFIG_PCI_DEVICES is set.
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will make it for example easier if the users want to disable
one of the two machines for their builds.
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Select the required devices in hw/ppc/Kconfig instead, so that
ppc-softmmu.mak only contains the user-selectable PREP switch.
Plug-in devices like NE2000_ISA are pulled in automatically by the
Kconfig build system now.
Cc: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The POWERNV switch should always select ISA_IPMI_BT, then the other
IPMI options are turned on automatically now.
CONFIG_DIMM should always be selected by the pseries machine,
which in turn depends on CONFIG_MEM_DEVICE since DIMM implements
this interface.
CONFIG_VIRTIO_VGA can be dropped from default-configs/ppc64-softmmu.mak
completely since this device is already automatically enabled via
hw/display/Kconfig now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
%-softmmu.mak only keep boards definitions in Kconfig mode.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-43-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-36-yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-42-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
remove default-configs/hyperv.mak and make dependencies
with Kconfig.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-41-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-40-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-39-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-38-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This way, the default-configs file only need to specify the boards
and any optional devices.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-37-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-36-yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This automatically removes the SCSI subsystem from the
binary altogether if no controllers are selected.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-34-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of including the same list of devices for each target,
let the host controllers select CONFIG_USB and make the devices
default to present whenever USB is available.
Done with the following script:
while read i; do
i=${i%=y}; i=${i#CONFIG_}
sed -i -e'/^config '$i'$/!b' -en \
-e'a\' -e' default y\' -e' depends on USB' \
`grep -lw $i hw/*/Kconfig`
done < default-configs/usb.mak
followed by adding "select USB" on the host controllers.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-33-yang.zhong@intel.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is really nothing special in these devices; they are just
ISA devices. Instead of including them for each target,
set CONFIG_ISA_BUS to true, and make the devices default to present
whenever ISA is available. More conversion of ISA devices will
follow.
Done with the following script:
while read i; do
i=${i%=y}; i=${i#CONFIG_}
sed -i -e'/^config '$i'$/!b' -en \
-e'a\' -e' default y\' -e' depends on ISA_BUS' \
`grep -lw $i hw/*/Kconfig`
done < default-configs/sound.mak
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-32-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of including the same list of devices for each target,
set CONFIG_PCI to true, and make the devices default to present
whenever PCI is available. However, s390x does not want all the
PCI devices, so there is a separate symbol to enable them.
Done mostly with the following script:
while read i; do
i=${i%=y}; i=${i#CONFIG_}
sed -i -e'/^config '$i'$/!b' -en \
-e'a\' -e' default y if PCI_DEVICES\' -e' depends on PCI' \
`grep -lw $i hw/*/Kconfig`
done < default-configs/pci.mak
followed by replacing a few "depends on" clauses with "select"
whenever the symbol is not really related to PCI.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-31-yang.zhong@intel.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make pcie splited from pci and make it configurable.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-30-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-29-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Devices that are mostly used for testing purposes (for example in
endianness-test) will be moved under a new symbol CONFIG_TEST_DEVICES
that can be disabled in the default-configs file. This makes
it easier to drop this code from QEMU if desirable.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The make_device_config.sh script is replaced by minikconf, which
is modified to support the same command line as its predecessor.
The roots of the parsing are default-configs/*.mak, Kconfig.host and
hw/Kconfig. One difference with make_device_config.sh is that all symbols
have to be defined in a Kconfig file, including those coming from the
configure script. This is the reason for the Kconfig.host file introduced
in the previous patch. Whenever a file in default-configs/*.mak used
$(...) to refer to a config-host.mak symbol, this is replaced by a
Kconfig dependency; this part must be done already in this patch
for bisectability.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-28-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use CONFIG_EDID to make edid-generate.c and edid-region.c
configurable.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-26-yang.zhong@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Lots of work on tests: BiosTablesTest UEFI app,
vhost-user testing for non-Linux hosts.
Misc cleanups and fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJccBqMAAoJECgfDbjSjVRpvSEIAKYPRNdCBX/SSS/L/tmJS5Zt
8IyU/HW1YJ249vO+aT6z4Q3QPgqNC3KjXC3brx/WRoPZnRroen4rv2Kqnk6SayPa
a52d2ubXKWxb3swdG1CAVzFRhq/ABpgAPx0dr1JW+RXgo2lxpJ4GNYxKMosQTaPE
hRNeXl1XlcIK525kJhFH3Hlij9mTRuY6T7ydpPQd8dUq2dBRaL9RrzZRrkZxCy6l
gQPUqNzPhG0XXyOiJmwYyVX0zGzbYrMLrMQAor2SBIYmU+zv2eZGPJUYxoMTUMzt
YR0WCpvkvPITlAryaBoozAIDYVz8PxBRT1KRwpDal+2rzlm6o+veKDiF8R46gn0=
=GzUz
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pci, pc, virtio: fixes, cleanups, tests
Lots of work on tests: BiosTablesTest UEFI app,
vhost-user testing for non-Linux hosts.
Misc cleanups and fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 22 Feb 2019 15:51:40 GMT
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (26 commits)
pci: Sanity test minimum downstream LNKSTA
hw/smbios: fix offset of type 3 sku field
pci: Move NVIDIA vendor id to the rest of ids
virtio-balloon: Safely handle BALLOON_PAGE_SIZE < host page size
virtio-balloon: Use ram_block_discard_range() instead of raw madvise()
virtio-balloon: Rework ballon_page() interface
virtio-balloon: Corrections to address verification
virtio-balloon: Remove unnecessary MADV_WILLNEED on deflate
i386/kvm: ignore masked irqs when update msi routes
contrib/vhost-user-blk: fix the compilation issue
Revert "contrib/vhost-user-blk: fix the compilation issue"
pc-dimm: use same mechanism for [get|set]_addr
tests/data: introduce "uefi-boot-images" with the "bios-tables-test" ISOs
tests/uefi-test-tools: add build scripts
tests: introduce "uefi-test-tools" with the BiosTablesTest UEFI app
roms: build the EfiRom utility from the roms/edk2 submodule
roms: add the edk2 project as a git submodule
vhost-user-test: create a temporary directory per TestServer
vhost-user-test: small changes to init_hugepagefs
vhost-user-test: create a main loop per TestServer
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement a model of the Message Handling Unit (MHU) found in
the Arm SSE-200. This is a simple device which just contains
some registers which allow the two cores of the SSE-200
to raise interrupts on each other.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190219125808.25174-2-peter.maydell@linaro.org
The Musca-A and Musca-B1 development boards are based on the
SSE-200 subsystem for embedded. Implement an initial skeleton
model of these boards, which are similar but not identical.
This commit creates the board model with the SSE and the IRQ
splitters to wire IRQs up to its two CPUs. As yet there
are no devices and no memory: these will be added later.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
vhost-user does not depend on Linux; it can run on any POSIX system. Restrict
vhost-kernel to Linux in hw/virtio/vhost-backend.c, everything else can be
compiled on all POSIX systems.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1543851204-41186-4-git-send-email-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1550165756-21617-4-git-send-email-pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make hw/vfio configurable and add new CONFIG_VFIO_* to the
default-configs/s390x*-softmmu.mak. This allow a finer-grain
selection of the various VFIO backends.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-28-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Create separate variables for these components, they are
used in many boards but not all. This allows finer-grain
selection of the included code with default-configs/*.mak.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the new configs to default-configs/tricore-sofmmu.mak.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-26-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the new configs to default-configs/or1k-sofmmu.mak.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-25-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CONFIG_MOXIE added for moxiesim board.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-24-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the new configs to default-configs/hppa-sofmmu.mak.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20190202072456.6468-23-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the new configs to default-configs/cris-sofmmu.mak.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-22-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the new configs to default-configs/alpha-sofmmu.mak.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20190202072456.6468-21-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the new configs to default-configs/sparc64-sofmmu.mak.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-20-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the new configs to default-configs/riscv*-sofmmu.mak.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-19-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CONFIG_NIOS2_10M50 added for 10m50 dev board.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-18-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the new CONFIG_* values to default-config/xtensa*-softmmu.mak.
Signed-off-by: Ákos Kovács <akoskovacs@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20190202072456.6468-17-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CONFIG_LEON3 added to default-configs/sparc-softmmu.mak.
Signed-off-by: Ákos Kovács <akoskovacs@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-15-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make hw/s390x configurable and add new CONFIG_* to the
default-configs/s390x*-softmmu.mak. This will be used to
enable/disable vfio-ccw.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-14-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make hw/sh4 configurable and add new CONFIG_* to the
default-configs/sh4*-softmmu.mak.
Signed-off-by: Ákos Kovács <akoskovacs@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-13-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CONFIG_PPC405, CONFIG_PPC440, CONFIG_MAC_OLDWORLD, CONFIG_MAX_NEWWORLD
and CONFIG_VIRTEX configuration options created for
default-configs/ppc*-softmmu.mak.
Signed-off-by: Ákos Kovács <akoskovacs@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-12-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the new configs to default-configs/mips*-sofmmu.mak.
Signed-off-by: Ákos Kovács <akoskovacs@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-11-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CONFIG_PETALOGIX_* and CONFIG_XLNX_* configs added to
default-configs/microblaze-softmmu.mak and
default-configs/microblazeel-softmmu.mak.
Signed-off-by: Ákos Kovács <akoskovacs@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-10-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CONFIG_AN5206, CONFIG_MCF5206 and CONFIG_MCF5208 make
variables created for m68k boards, and added to
default-configs/m86k-softmmu.mak.
Signed-off-by: Ákos Kovács <akoskovacs@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-9-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make ARM virt code configurable and the new CONFIG_ARM_VIRT
definitions added to the default-configs/arm-softmmu.mak.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-8-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CONFIG_PIIX and CONFIG_Q35 created for the pc board object files. These
are enabled automatically at default-configs/i386-softmmu.mak and
default-configs/x86_64-softmmu.mak
Signed-off-by: Ákos Kovács <akoskovacs@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-7-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Do not link it unconditionally into all binaries.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-6-yang.zhong@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Change the CONFIGs for PCI EXPRESS and make module name more
clear for code files.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-5-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
ARM should not have an ISA bus, this device should not be enabled.
Kconfig allows to clean up the dependencies and remove CONFIG_ISA_BUS=y
from ARM, and then catches a contradiction between the hardcoded
CONFIG_SERIAL_ISA=y and CONFIG_ISA_BUS=n.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-2-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The SSE-200 has a CPU_IDENTITY register block, which is a set of
read-only registers. As well as the usual PID/CID registers, there
is a single CPUID register which indicates whether the CPU is CPU 0
or CPU 1. Implement a model of this register block.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-20-peter.maydell@linaro.org
Rename the files that used to be iotkit.[ch] to
armsse.[ch] to reflect the fact they new cover
multiple Arm subsystems for embedded.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-8-peter.maydell@linaro.org
The TMU device requires both X11 and OpenGL.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190130120005.23123-4-philmd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For consistency with other devices, rename
virtio_host_{initfn,pci_info} to virtio_input_host_{initfn,info}.
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This pull request contains the first set of RISC-V patches I'd like to
target for the 3.2 development cycle. It's really just a collection of
bug fixes with one major new feature: PCIe can now be attached to RISC-V
guests.
This has passed my usual test of booting the latest Linux RC into a
Fedora disk image on the virt machine.
-----BEGIN PGP SIGNATURE-----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=BAOm
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/palmer/tags/riscv-for-master-3.2-part1' into staging
RISC-V Changes for 3.2, Part 1
This pull request contains the first set of RISC-V patches I'd like to
target for the 3.2 development cycle. It's really just a collection of
bug fixes with one major new feature: PCIe can now be attached to RISC-V
guests.
This has passed my usual test of booting the latest Linux RC into a
Fedora disk image on the virt machine.
# gpg: Signature made Fri 21 Dec 2018 16:01:29 GMT
# gpg: using RSA key EF4CA1502CCBAB41
# gpg: Good signature from "Palmer Dabbelt <palmer@dabbelt.com>"
# gpg: aka "Palmer Dabbelt <palmer@sifive.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 00CE 76D1 8349 60DF CE88 6DF8 EF4C A150 2CCB AB41
* remotes/palmer/tags/riscv-for-master-3.2-part1:
MAINTAINERS: Mark RISC-V as Supported
riscv/cpu: use device_class_set_parent_realize
target/riscv/pmp.c: Fix pmp_decode_napot()
sifive_uart: Implement interrupt pending register
RISC-V: Enable second UART on sifive_e and sifive_u
RISC-V: Fix PLIC pending bitfield reads
RISC-V: Fix CLINT timecmp low 32-bit writes
RISC-V: Add hartid and \n to interrupt logging
sifive_u: Set 'clock-frequency' DT property for SiFive UART
sifive_u: Add clock DT node for GEM ethernet
riscv: Enable VGA and PCIE_VGA
hw/riscv/virt: Connect the gpex PCIe
hw/riscv/virt: Adjust memory layout spacing
hw/riscv/virt: Increase the number of interrupts
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
sPAPRXive models the XIVE interrupt controller of the sPAPR machine.
It inherits from the XiveRouter and provisions storage for the routing
tables :
- Event Assignment Structure (EAS)
- Event Notification Descriptor (END)
The sPAPRXive model incorporates an internal XiveSource for the IPIs
and for the interrupts of the virtual devices of the guest. This model
is consistent with XIVE architecture which also incorporates an
internal IVSE for IPIs and accelerator interrupts in the IVRE
sub-engine.
The sPAPRXive model exports two memory regions, one for the ESB
trigger and management pages used to control the sources and one for
the TIMA pages. They are mapped by default at the addresses found on
chip 0 of a baremetal system. This is also consistent with the XIVE
architecture which defines a Virtualization Controller BAR for the
internal IVSE ESB pages and a Thread Managment BAR for the TIMA.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Fold in field accessor fixes]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The first sub-engine of the overall XIVE architecture is the Interrupt
Virtualization Source Engine (IVSE). An IVSE can be integrated into
another logic, like in a PCI PHB or in the main interrupt controller
to manage IPIs.
Each IVSE instance is associated with an Event State Buffer (ESB) that
contains a two bit state entry for each possible event source. When an
event is signaled to the IVSE, by MMIO or some other means, the
associated interrupt state bits are fetched from the ESB and
modified. Depending on the resulting ESB state, the event is forwarded
to the IVRE sub-engine of the controller doing the routing.
Each supported ESB entry is associated with either a single or a
even/odd pair of pages which provides commands to manage the source:
to EOI, to turn off the source for instance.
On a sPAPR machine, the O/S will obtain the page address of the ESB
entry associated with a source and its characteristic using the
H_INT_GET_SOURCE_INFO hcall. On PowerNV, a similar OPAL call is used.
The xive_source_notify() routine is in charge forwarding the source
event notification to the routing engine. It will be filled later on.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Enable compile support for VGA devices. This allows the user to conenct
a display by adding '-device bochs-display -display sdl' to their
command line argument.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Tested-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Connect the gpex PCIe device based on the device tree included in the
HiFive Unleashed ROM.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The spapr-rng device is suboptimal when compared to virtio-rng, so
users might want to disable it in their builds. Thus let's introduce
a proper CONFIG switch to allow us to compile QEMU without this device.
The function spapr_rng_populate_dt is required for linking, so move it
to a different location.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add a model of Xilinx Versal SoC.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20181102131913.1535-2-edgar.iglesias@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(Thank you to Thomas Huth)
v2: fix 32bit build with updated patch (v3) from Philippe Mathieu-Daudé
built in a 32bit debian sid chroot
-----BEGIN PGP SIGNATURE-----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=sHPv
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/vivier2/tags/qemu-trivial-for-3.1-pull-request' into staging
QEMU trivial patches collected between June and October 2018
(Thank you to Thomas Huth)
v2: fix 32bit build with updated patch (v3) from Philippe Mathieu-Daudé
built in a 32bit debian sid chroot
# gpg: Signature made Tue 30 Oct 2018 11:23:01 GMT
# gpg: using RSA key F30C38BD3F2FBE3C
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>"
# gpg: aka "Laurent Vivier <laurent@vivier.eu>"
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>"
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier2/tags/qemu-trivial-for-3.1-pull-request:
milkymist-minimac2: Use qemu_log_mask(GUEST_ERROR) instead of error_report
ppc: move at24c to its own CONFIG_ symbol
hw/intc/gicv3: Remove useless parenthesis around DIV_ROUND_UP macro
hw/pci-host: Remove useless parenthesis around DIV_ROUND_UP macro
tests/bios-tables-test: Remove an useless cast
xen: Use the PCI_DEVICE macro
qobject: Catch another straggler for use of qdict_put_str()
configure: Support pkg-config for zlib
tests: Fix typos in comments and help message (found by codespell)
cpu.h: fix a typo in comment
linux-user: fix comment s/atomic_write/atomic_set/
qemu-iotests: make 218 executable
scripts/qemu.py: remove trailing quotes on docstring
scripts/decodetree.py: remove unused imports
docs/devel/testing.rst: add missing newlines after code block
qemu-iotests: fix filename containing checks
tests/tcg/README: fix location for lm32 tests
memory.h: fix typos in comments
vga_int: remove unused function protype
configs/alpha: Remove unused CONFIG_PARALLEL_ISA switch
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
AT24c EEPROM is currently gated by CONFIG_I2C, and as such it is
being included in all emulators that use I2C, even if they do not
really need it. Separate it and, since it was added for the e500
machines, add it to qemu-system-ppc and qemu-system-ppc64.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20180522191743.12872-1-pbonzini@redhat.com>
[lv: rebase]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
We don't use CONFIG_PARALLEL_ISA in any of our Makefiles, so this
is just a dead config option which can be removed.
Fixes: a4cb773928
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <1540376314-5727-1-git-send-email-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Some architectures might support memory devices, while they don't
support DIMM/NVDIMM. So let's
- Rename CONFIG_MEM_HOTPLUG to CONFIG_MEM_DEVICE
- Introduce CONFIG_DIMM and use it similarly to CONFIG NVDIMM
CONFIG_DIMM and CONFIG_NVDIMM require CONFIG_MEM_DEVICE.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20181005092024.14344-7-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Since the I/O Bridge device is not implemented, Use the
TYPE_UNIMPLEMENTED_DEVICE which suits better: if the user
asks for 'unimp' warnings via the -d option then all accesses
will generate logging.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Artyom Tarasenko <atar4qemu@gmail.com>
Message-Id: <20181002212522.23303-10-f4bug@amsat.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This device is not user-creatable and currently only used for the
"alpha" target. So if the user does not want to compile alpha-softmmu,
we should also not compile this device. Add a proper config switch to
be able to compile this more flexibly.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Accumulate HYPERV config options in a dedicated file. There are only
two so far; more will be added later.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921082041.29380-5-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This allows modern architectures which don't care about vga
compatibility (risc-v for example) build bochs-display without
including all vga emulation too.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20181005160147.892-2-kraxel@redhat.com
Introduces a VFIO based AP device. The device is defined via
the QEMU command line by specifying:
-device vfio-ap,sysfsdev=<path-to-mediated-matrix-device>
There may be only one vfio-ap device configured for a guest.
The mediated matrix device is created by the VFIO AP device
driver by writing a UUID to a sysfs attribute file (see
docs/vfio-ap.txt). The mediated matrix device will be named
after the UUID. Symbolic links to the $uuid are created in
many places, so the path to the mediated matrix device $uuid
can be specified in any of the following ways:
/sys/devices/vfio_ap/matrix/$uuid
/sys/devices/vfio_ap/matrix/mdev_supported_types/vfio_ap-passthrough/devices/$uuid
/sys/bus/mdev/devices/$uuid
/sys/bus/mdev/drivers/vfio_mdev/$uuid
When the vfio-ap device is realized, it acquires and opens the
VFIO iommu group to which the mediated matrix device is
bound. This causes a VFIO group notification event to be
signaled. The vfio_ap device driver's group notification
handler will get called at which time the device driver
will configure the the AP devices to which the guest will
be granted access.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Tested-by: Pierre Morel <pmorel@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Pierre Morel <pmorel@linux.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20181010170309.12045-6-akrowiak@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[CH: added missing g_free and device category]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The nRF51 is a Cortex-M0 microcontroller with an on-board radio module,
plus other common ARM SoC peripherals.
http://infocenter.nordicsemi.com/pdf/nRF51_RM_v3.0.pdf
This defines a basic model of the CPU and memory, with no peripherals
implemented at this stage.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-id: 20180831220920.27113-3-joel@jms.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: wrapped a few long lines]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is no known available OS for ppc around anymore that uses page
sizes below 4k, so it does not make much sense that we keep wasting
our time on building and testing the ppcemb-softmmu target. It has
been deprecated since two releases, and nobody complained, so let's
remove this now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If we ever changed that, just make the things that are different
explicit.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Implement a model of the TrustZone Master Securtiy Controller,
as documented in the Arm CoreLink SIE-200 System IP for
Embedded TRM (DDI0571G):
https://developer.arm.com/products/architecture/m-profile/docs/ddi0571/g
The MSC is intended to sit in front of a device which can
be a bus master (eg a DMA controller) and programmably gate
its transactions. This allows a bus-mastering device to be
controlled by non-secure code but still restricted from
making accesses to addresses which are secure-only.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-12-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Implement the IoTKit system control element's system information
block; this is just a pair of read-only version/config registers,
plus the usual PID/CID ID registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-10-peter.maydell@linaro.org
The Arm IoTKit includes a system control element which
provides a block of read-only ID registers and a block
of read-write control registers. Implement a minimal
version of this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-9-peter.maydell@linaro.org
The Arm Cortex-M System Design Kit includes a "dual-input timer module"
which combines two programmable down-counters. Implement a model
of this device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-4-peter.maydell@linaro.org
The Arm Cortex-M System Design Kit includes a simple watchdog module
based on a 32-bit down-counter. Implement this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Emulate the i2c part of SM501 which is used to access the EDID info
from a monitor.
The vmstate structure is changed and its version is increased but
SM501 is only used on SH and PPC sam460ex machines that don't support
cross-version migration.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Connect the Cadence GEM ethernet device. This also requires us to
expose the plic interrupt lines.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Drivers for this card exists on PPC-based AmigaOS guests so it is useful to
allow users to emulate the graphics card for PPC machines.
As cirrus vga is currently preferred over std(vga) in absence of any user
choice, this change also sets the default display of spapr machines to
std as otherwise qemu refuses to start these machines. Not specifying an
explicit graphics mode is for instance done by 'make check'.
Signed-off-by: Sebastian Bauer <mail@sebastianbauer.info>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Basic emulation of the M41T80 serial (I2C) RTC chip. Only getting time
of day is implemented. Setting time and RTC alarm are not supported.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
At present the Sam460ex board is activated by the general CONFIG_PPC4XX
option. However that includes the board for both ppc-softmmu and
(deprecated) ppcemb-softmmu builds. As Sam460ex is developed, that would
require adding more things into ppcemb-softmmu, which we don't want to do.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
* hw/intc/arm_gicv3: fix wrong values when reading IPRIORITYR
* target/arm: fix read of freed memory in kvm_arm_machine_init_done()
* virt: support up to 512 CPUs
* virt: support 256MB ECAM PCI region (for more PCI devices)
* xlnx-zynqmp: Use Cortex-R5F, not Cortex-R5
* mps2-tz: Implement and use the TrustZone Memory Protection Controller
* target/arm: enforce alignment checking for v6M cores
* xen: Don't use memory_region_init_ram_nomigrate() in pci_assign_dev_load_option_rom()
* vl.c: Don't zero-initialize statics for serial_hds
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1T5q
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20180622' into staging
target-arm queue:
* hw/intc/arm_gicv3: fix wrong values when reading IPRIORITYR
* target/arm: fix read of freed memory in kvm_arm_machine_init_done()
* virt: support up to 512 CPUs
* virt: support 256MB ECAM PCI region (for more PCI devices)
* xlnx-zynqmp: Use Cortex-R5F, not Cortex-R5
* mps2-tz: Implement and use the TrustZone Memory Protection Controller
* target/arm: enforce alignment checking for v6M cores
* xen: Don't use memory_region_init_ram_nomigrate() in pci_assign_dev_load_option_rom()
* vl.c: Don't zero-initialize statics for serial_hds
# gpg: Signature made Fri 22 Jun 2018 13:56:00 BST
# gpg: using RSA key 3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20180622: (28 commits)
xen: Don't use memory_region_init_ram_nomigrate() in pci_assign_dev_load_option_rom()
vl.c: Don't zero-initialize statics for serial_hds
target/arm: Strict alignment for ARMv6-M and ARMv8-M Baseline
target/arm: Introduce ARM_FEATURE_M_MAIN
hw/arm/mps2-tz.c: Instantiate MPCs
hw/arm/iotkit: Wire up MPC interrupt lines
hw/arm/iotkit: Instantiate MPC
hw/misc/iotkit-secctl.c: Implement SECMPCINTSTATUS
hw/misc/tz_mpc.c: Honour the BLK_LUT settings in translate
hw/misc/tz-mpc.c: Implement correct blocked-access behaviour
hw/misc/tz-mpc.c: Implement registers
hw/misc/tz-mpc.c: Implement the Arm TrustZone Memory Protection Controller
xlnx-zynqmp: Swap Cortex-R5 for Cortex-R5F
target-arm: Add the Cortex-R5F
hw/arm/virt: Increase max_cpus to 512
hw/arm/virt: Use 256MB ECAM region by default
hw/arm/virt: Add virt-3.0 machine type
hw/arm/virt: Add a new 256MB ECAM region
hw/arm/virt: Register two redistributor regions when necessary
hw/arm/virt-acpi-build: Advertise one or two GICR structures
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the Arm TrustZone Memory Protection Controller, which sits
in front of RAM and allows secure software to configure it to either
pass through or reject transactions.
We implement the MPC as a QEMU IOMMU, which will direct transactions
either through to the devices and memory behind it or to a special
"never works" AddressSpace if they are blocked.
This initial commit implements the skeleton of the device:
* it always permits accesses
* it doesn't implement most of the registers
* it doesn't implement the interrupt or other behaviour
for blocked transactions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180620132032.28865-2-peter.maydell@linaro.org
As well as being able to generate its own i2c transactions, the ppc4xx
i2c controller has a DIRECTCNTL register which allows explicit control
of the i2c lines.
Using this register an OS can directly bitbang i2c operations. In
order to let emulated i2c devices respond to this, we need to wire up
the DIRECTCNTL register to qemu's bitbanged i2c handling code.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PMU device supercedes the CUDA device found on older New World Macs and
is supported by a larger number of guest OSs from OS 9 to OS X 10.5.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
PMU-enabled New World Macs expose their GPIOs via a separate memory region
within the macio device.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Specs are available here :
https://www.nxp.com/docs/en/application-note/AN264.pdf
This is a simple model supporting the basic registers for led and GPIO
mode. The device also supports two blinking rates but not the model
yet.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180530064049.27976-7-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is only half of the work, because the proxy devices (virtio-*-pci,
virtio-*-ccw, etc.) are still included unconditionally. It is still a
move in the right direction.
Based-on: <20180522194943.24871-1-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The patch introduces the smmu base device and class for the ARM
smmu. Devices for specific versions will be derived from this
base device.
We also introduce some important datatypes.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1524665762-31355-2-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- small cleanup for xtensa registers dumping (-d cpu);
- add support for debugging linux-user process with xtensa-linux-gdb
(as opposed to xtensa-elf-gdb), which can only access unprivileged
registers;
- enable MTTCG for target/xtensa;
- cleanup in linux-user/mmap area making sure that it works correctly
with limited 30-bit-wide user address space;
- import xtensa-specific definitions from the linux kernel,
conditionalize user-only/softmmu-only code and add handlers for
signals, exceptions, process/thread creation and core registers dumping.
-----BEGIN PGP SIGNATURE-----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=UCny
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/xtensa/tags/20180316-xtensa' into staging
target/xtensa linux-user support.
- small cleanup for xtensa registers dumping (-d cpu);
- add support for debugging linux-user process with xtensa-linux-gdb
(as opposed to xtensa-elf-gdb), which can only access unprivileged
registers;
- enable MTTCG for target/xtensa;
- cleanup in linux-user/mmap area making sure that it works correctly
with limited 30-bit-wide user address space;
- import xtensa-specific definitions from the linux kernel,
conditionalize user-only/softmmu-only code and add handlers for
signals, exceptions, process/thread creation and core registers dumping.
# gpg: Signature made Fri 16 Mar 2018 16:46:19 GMT
# gpg: using RSA key 51F9CC91F83FA044
# gpg: Good signature from "Max Filippov <filippov@cadence.com>"
# gpg: aka "Max Filippov <max.filippov@cogentembedded.com>"
# gpg: aka "Max Filippov <jcmvbkbc@gmail.com>"
# Primary key fingerprint: 2B67 854B 98E5 327D CDEB 17D8 51F9 CC91 F83F A044
* remotes/xtensa/tags/20180316-xtensa:
MAINTAINERS: fix W: address for xtensa
qemu-binfmt-conf.sh: add qemu-xtensa
target/xtensa: add linux-user support
linux-user: drop unused target_msync function
linux-user: fix target_mprotect/target_munmap error return values
linux-user: fix assertion in shmdt
linux-user: fix mmap/munmap/mprotect/mremap/shmat
target/xtensa: support MTTCG
target/xtensa: use correct number of registers in gdbstub
target/xtensa: mark register windows in the dump
target/xtensa: dump correct physical registers
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# linux-user/syscall.c
Import list of syscalls from the kernel source. Conditionalize code/data
that is only used with softmmu. Implement exception handlers. Implement
signal hander (only the core registers for now, no coprocessors or TIE).
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
* SCSI fix to pass maximum transfer size (Daniel Barboza)
* chardev fixes and improved iothread support (Daniel Berrangé, Peter)
* checkpatch tweak (Eric)
* make help tweak (Marc-André)
* make more PCI NICs available with -net or -nic (myself)
* change default q35 NIC to e1000e (myself)
* SCSI support for NDOB bit (myself)
* membarrier system call support (myself)
* SuperIO refactoring (Philippe)
* miscellaneous cleanups and fixes (Thomas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJapqaMAAoJEL/70l94x66DQoUH/Rvg+a8giz/SrEA4P8D3Cb2z
4GNbNUUoy4oU0ltD5IAMskMwpOsvl1batE0D+pKIlfO9NV4+Cj2kpgo0p9TxoYqM
VCby3wRtx27zb5nVytC6M++iIKXmeEMqXmFw61I6umddNPSl4IR3hiHEE0DM+7dV
UPIOvJeEiazyQaw3Iw+ZctNn8dDBKc/+6oxP9xRcYTaZ6hB4G9RZkqGNNSLcJkk7
R0UotdjzIZhyWMOkjIwlpTF4sWv8gsYUV4bPYKMYho5B0Obda2dBM3I1kpA8yDa/
xZ5lheOaAVBZvM5aMIcaQPa65MO9hLyXFmhMOgyfpJhLBBz6Qpa4OLLI6DeTN+0=
=UAgA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Record-replay lockstep execution, log dumper and fixes (Alex, Pavel)
* SCSI fix to pass maximum transfer size (Daniel Barboza)
* chardev fixes and improved iothread support (Daniel Berrangé, Peter)
* checkpatch tweak (Eric)
* make help tweak (Marc-André)
* make more PCI NICs available with -net or -nic (myself)
* change default q35 NIC to e1000e (myself)
* SCSI support for NDOB bit (myself)
* membarrier system call support (myself)
* SuperIO refactoring (Philippe)
* miscellaneous cleanups and fixes (Thomas)
# gpg: Signature made Mon 12 Mar 2018 16:10:52 GMT
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (69 commits)
tcg: fix cpu_io_recompile
replay: update documentation
replay: save vmstate of the asynchronous events
replay: don't process async events when warping the clock
scripts/replay-dump.py: replay log dumper
replay: avoid recursive call of checkpoints
replay: check return values of fwrite
replay: push replay_mutex_lock up the call tree
replay: don't destroy mutex at exit
replay: make locking visible outside replay code
replay/replay-internal.c: track holding of replay_lock
replay/replay.c: bump REPLAY_VERSION again
replay: save prior value of the host clock
replay: added replay log format description
replay: fix save/load vm for non-empty queue
replay: fixed replay_enable_events
replay: fix processing async events
cpu-exec: fix exception_index handling
hw/i386/pc: Factor out the superio code
hw/alpha/dp264: Use the TYPE_SMC37C669_SUPERIO
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# default-configs/i386-softmmu.mak
# default-configs/x86_64-softmmu.mak
Add a new memory encryption object 'sev-guest'. The object will be used
to create encrypted VMs on AMD EPYC CPU. The object provides the properties
to pass guest owner's public Diffie-hellman key, guest policy and session
information required to create the memory encryption context within the
SEV firmware.
e.g to launch SEV guest
# $QEMU \
-object sev-guest,id=sev0 \
-machine ....,memory-encryption=sev0
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-25-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-24-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow distributions to disable the Intel and/or AMD IOMMU devices.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A lot of ARM object files are linked into the executable unconditionally,
even though we have corresponding CONFIG switches like CONFIG_PXA2XX or
CONFIG_OMAP. We should make sure to use these switches in the Makefile so
that the users can disable certain unwanted boards and devices more easily.
While we're at it, also add some new switches for the boards that do not
have a CONFIG option yet.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-id: 1520266949-29817-1-git-send-email-thuth@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add code needed to get a functional PCI subsytem when using in
conjunction with upstream Linux guest (4.13+). Tested to work against
"e1000e" (network adapter, using MSI interrupts) as well as
"usb-ehci" (USB controller, using legacy PCI interrupts).
Based on "i.MX6 Applications Processor Reference Manual" (Document
Number: IMX6DQRM Rev. 4) as well as corresponding dirver in Linux
kernel (circa 4.13 - 4.16 found in drivers/pci/dwc/*)
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds RISC-V into the build system enabling the following targets:
- riscv32-softmmu
- riscv64-softmmu
- riscv32-linux-user
- riscv64-linux-user
This adds defaults configs for RISC-V, enables the build for the RISC-V
CPU core, hardware, and Linux User Emulation. The 'qemu-binfmt-conf.sh'
script is updated to add the RISC-V ELF magic.
Expected checkpatch errors for consistency reasons:
ERROR: line over 90 characters
FILE: scripts/qemu-binfmt-conf.sh
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Michael Clark <mjc@sifive.com>
Add emulation of aCube Sam460ex board based on AMCC 460EX embedded SoC.
This is not a complete implementation yet with a lot of components
still missing but enough for the U-Boot firmware to start and to boot
a Linux kernel or AROS.
Signed-off-by: François Revol <revol@free.fr>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The Arm IoT Kit includes a "security controller" which is largely a
collection of registers for controlling the PPCs and other bits of
glue in the system. This commit provides the initial skeleton of the
device, implementing just the ID registers, and a couple of read-only
read-as-zero registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-16-peter.maydell@linaro.org
Add a model of the TrustZone peripheral protection controller (PPC),
which is used to gate transactions to non-TZ-aware peripherals so
that secure software can configure them to not be accessible to
non-secure software.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-15-peter.maydell@linaro.org
The MPS2 AN505 FPGA image includes a "FPGA control block"
which is a small set of registers handling LEDs, buttons
and some counters.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-14-peter.maydell@linaro.org
This adds the SiI9022 (and implicitly EDID I2C) device to the ARM
Versatile Express machine, and selects the two I2C devices necessary
in the arm-softmmu.mak configuration so everything will build
smoothly.
I am implementing proper handling of the graphics in the Linux
kernel and adding proper emulation of SiI9022 and EDID makes the
driver probe as nicely as before, retrieving the resolutions
supported by the "QEMU monitor" and overall just working nice.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Message-id: 20180227104903.21353-6-linus.walleij@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The core SJA1000 support is independent of following
patches which map SJA1000 chip to PCI boards.
The work is based on Jin Yang GSoC 2013 work funded
by Google and mentored in frame of RTEMS project GSoC
slot donated to QEMU.
Rewritten for QEMU-2.0+ versions and architecture cleanup
by Pavel Pisa (Czech Technical University in Prague).
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The CanBusState state structure is created for each
emulated CAN channel. Individual clients/emulated
CAN interfaces or host interface connection registers
to the bus by CanBusClientState structure.
The CAN core is prepared to support connection to the
real host CAN bus network. The commit with such support
for Linux SocketCAN follows.
Implementation is as simple as possible. There is no state to be
migrated, and messages prioritization and queuing are not considered
for now. But it is intended to be extended when need arises.
Development repository and more documentation at
https://gitlab.fel.cvut.cz/canbus/qemu-canbus
The work is based on Jin Yang GSoC 2013 work funded
by Google and mentored in frame of RTEMS project GSoC
slot donated to QEMU.
Rewritten for QEMU-2.0+ versions and architecture cleanup
by Pavel Pisa (Czech Technical University in Prague).
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The MOS6522 VIA forms the bridge part of several Mac devices, including the
Mac via-cuda and via-pmu devices. Introduce a standard mos6522 device that
can be shared amongst multiple implementations.
This is effectively taking the 6522 parts out of cuda.c and turning them
into a separate device whilst also applying some style tidy-ups and including
a conversion to trace-events.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The i2c core and the at24c EEPROM should only be compiled and linked
on the machines that support i2c. Otherwise it's quite strange to see
the at24c-eeprom to be "available" on qemu-system-s390x for example.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1516634853-15883-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that we have the prerequisites in target/hppa/,
implement the hardware for a PA7100LC.
This also enables build for hppa-softmmu.
Signed-off-by: Helge Deller <deller@gmx.de>
[rth: Since it is all new code, squashed all branch development
withing hw/hppa/ to a single patch.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
tpm_crb is a device for TPM 2.0 Command Response Buffer (CRB)
Interface as defined in TCG PC Client Platform TPM Profile (PTP)
Specification Family “2.0” Level 00 Revision 01.03 v22.
The PTP allows device implementation to switch between TIS and CRB
model at run time, but given that CRB is a simpler device to
implement, I chose to implement it as a different device.
The device doesn't implement other locality than 0 for now (my laptop
TPM doesn't either, so I assume this isn't so bad)
Tested with some success with Linux upstream and Windows 10, seabios &
modified ovmf. The device is recognized and correctly transmit
command/response with passthrough & emu. However, we are missing PPI
ACPI part atm.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Add the PMU IO Module Interrupt controller device.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
In preperation for having an ARM and MicroBlaze ZynqMP machine let's
split out the current ARM specific config options.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
This is the final stage in correcting the naming convention with respect to
sabre, APB and PBM. It is effectively a file rename from apb.c to sabre.c
along with touching up a few constants to remove the remaining references
to APB.
Note that as part of the rename process the configuration variable
CONFIG_PCI_APB is changed to CONFIG_PCI_SABRE.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
Move the QOM type and macros into a new include/hw/pci-bridge/simba.h
file, and add a new CONFIG_SIMBA Makefile.objs variable which is enabled
for sparc64-softmmu builds only.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
Order the CONFIG switches in ppc-softmmu.mak according to the machine
classes where they are used (embedded, Mac or PReP), so that it is
easier for the users to disable a set of switches completely if they
are not needed.
Also add the missing CONFIG_IDE_SII3112 switch to the embedded section
which was previously only added to ppcemb-softmmu.mak.
And while we're at it, also remove the CONFIG_IDE_CMD646 switch since
this controller does not seem to be used by any ppc machine in QEMU.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
qemu-softmmu-ppc64 is supposed to be a superset of qemu-softmmu-ppc.
However, instead of simply including the 32-bit config file, we've
duplicated all CONFIG_xxx settings there instead. This way, we've missed
some CONFIG switches in ppc64-softmmu.mak which were only added to the
32-bit config file (e.g. CONFIG_SUNGEM). Let's fix this problem by
including the 32-bit config file into the 64-bit config file instead
of duplicating all the CONFIG switches there.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This commit introduces a new vhost-user device for block, it uses a
chardev to connect with the backend, same with Qemu virito-blk device,
Guest OS still uses the virtio-blk frontend driver.
To use it, start QEMU with command line like this:
qemu-system-x86_64 \
-chardev socket,id=char0,path=/path/vhost.socket \
-device vhost-user-blk-pci,chardev=char0,num-queues=2, \
bootindex=2... \
Users can use different parameters for `num-queues` and `bootindex`.
Different with exist Qemu virtio-blk host device, it makes more easy
for users to implement their own I/O processing logic, such as all
user space I/O stack against hardware block device. It uses the new
vhost messages(VHOST_USER_GET_CONFIG) to get block virtio config
information from backend process.
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add target aarch64_be-linux-user. This allows a qemu-aarch64_be binary
to be built that will run big-endian aarch64 binaries.
Signed-off-by: Michael Weiser <michael.weiser@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-id: 20171220212308.12614-5-michael.weiser@gmx.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a common generic PCI SATA controller that is also used in PCs
but more importantly guests running on the Sam460ex board prefer this
card and have a driver for it (unlike for other SATA controllers
already emulated).
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Acked-by: John Snow <jsnow@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add support for the Zynq Ultrascale MPSoc Generic QSPI.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-13-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
vmcoreinfo is built for all targets. However, it requires fw_cfg with
DMA operations support (write operation). Restrict vmcoreinfo exposure
to architectures that are supporting FW_CFG_DMA, that is arm-virt and
x86 only atm.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Daniel Henrique Barboza <danielhb@linux.vnet.ibm.com>
Tested-by: Daniel Henrique Barboza <danielhb@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add OpenRISC Multicore PIC which handles inter processor interrupts
(IPI) between cores. In OpenRISC all device interrupts are routed to
each core enabling this device to be simple.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Stafford Horne <shorne@gmail.com>
It is used by all PPC targets; we can give the directory its own
Makefile.objs file, and include it directly from target/ppc.
target/s390 can do the same when it starts using it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The device can not be instantiated on many non-x86 and just prints
some error messages, e.g.:
$ qemu-system-ppc64 -device vmxnet3 -M g3beige
[vmxnet3][WR][vmxnet3_init_msix]: Failed to initialize MSI-X, error -95
[vmxnet3][WR][vmxnet3_pci_realize]: Failed to initialize MSI-X, configuration is inconsistent.
Since vmxnet3 is a para-virtualized device that is only useful on x86,
it should also only be enabled on the x86 targets.
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Smartfusion2 SoC has hardened Microcontroller subsystem
and flash based FPGA fabric. This patch adds support for
Microcontroller subsystem in the SoC.
Signed-off-by: Subbaraya Sundeep <sundeep.lkml@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20170920201737.25723-5-f4bug@amsat.org
[PMD: drop cpu_model to directly use cpu type, check m3clk non null]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enable it by default for the sparc64-softmmu configuration.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
Using $(and ...) is dangerous here: It only works as long as the first
argument is set to 'y' or completely unset. It does not work if the
first argument is set to 'n' for example. Let's use the "land" make
function instead which has been written explicitely for this purpose.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1505759538-15365-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
