The mcycle/minstret counter's stop flag is mistakenly updated on a copy
on stack. Thus the counter increments even when the CY/IR bit in the
mcountinhibit register is set. This commit corrects its behavior.
Fixes: 3780e33732 (target/riscv: Support mcycle/minstret write operation)
Signed-off-by: Xu Lu <luxu.kernel@bytedance.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(cherry picked from commit 5cb0e7abe1)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Check the PMU available bitmask when checking if a counter is valid
rather than comparing the index against the number of PMUs.
Signed-off-by: Rob Bradford <rbradford@rivosinc.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Message-ID: <20231031154000.18134-3-rbradford@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The CSR register mseccfg is used by multiple extensions: Smepm and Zkr.
Consider this when checking the existence of the register.
Fixes: 77442380ec ("target/riscv: rvk: add CSR support for Zkr")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231030102105.19501-1-heinrich.schuchardt@canonical.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
zicntr is the Base Counters and Timers extension described in chapter 12
of the unprivileged spec. It describes support for RDCYCLE, RDTIME and
RDINSTRET.
QEMU already implements it in TCG way before it was a discrete
extension. zicntr is part of the RVA22 profile, so let's add it to QEMU
to make the future profile implementation flag complete. Given than it
represents an already existing feature, default it to 'true' for all
CPUs.
For TCG, we need a way to disable zicntr if the user wants to. This is
done by restricting access to the CYCLE, TIME, and INSTRET counters via
the 'ctr()' predicate when we're about to access them.
Disabling zicntr happens via the command line or if its dependency,
zicsr, happens to be disabled. We'll check for zicsr during realize()
and, in case it's absent, disable zicntr. However, if the user was
explicit about having zicntr support, error out instead of disabling it.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231023153927.435083-2-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Smepmp is a ratified extension which qemu refers to as epmp.
Rename epmp to smepmp and add it to extension list so that
it is added to the isa string.
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231019065546.1431579-1-mchitale@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This change adds support for inserting virtual interrupts from HS-mode
into VS-mode using hvien and hvip csrs. This also allows for IRQ filtering
from HS-mode.
Also, the spec doesn't mandate the interrupt to be actually supported
in hardware. Which allows HS-mode to assert virtual interrupts to VS-mode
that have no connection to any real interrupt events.
This is defined as part of the AIA specification [0], "6.3.2 Virtual
interrupts for VS level".
[0]: https://github.com/riscv/riscv-aia/releases/download/1.0/riscv-interrupts-1.0.pdf
Signed-off-by: Rajnesh Kanwal <rkanwal@rivosinc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20231016111736.28721-7-rkanwal@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This change adds support for inserting virtual interrupts from M-mode
into S-mode using mvien and mvip csrs. IRQ filtering is a use case of
this change, i-e M-mode can stop delegating an interrupt to S-mode and
instead enable it in MIE and receive those interrupts in M-mode and then
selectively inject the interrupt using mvien and mvip.
Also, the spec doesn't mandate the interrupt to be actually supported
in hardware. Which allows M-mode to assert virtual interrupts to S-mode
that have no connection to any real interrupt events.
This is defined as part of the AIA specification [0], "5.3 Interrupt
filtering and virtual interrupts for supervisor level".
[0]: https://github.com/riscv/riscv-aia/releases/download/1.0/riscv-interrupts-1.0.pdf
Signed-off-by: Rajnesh Kanwal <rkanwal@rivosinc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20231016111736.28721-6-rkanwal@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Add a leading 'z' to improve grepping. When one wants to search for uses
of zicsr they're more likely to do 'grep -i zicsr' than 'grep -i icsr'.
Suggested-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20231012164604.398496-3-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This function is the core of the RISC-V validations for TCG CPUs, and it
has a lot going on.
Functions in cpu.c were made public to allow them to be used by the KVM
accelerator class later on. 'cpu_cfg_ext_get_min_version()' is notably
hard to move it to another file due to its dependency with isa_edata_arr[]
array, thus make it public and use it as is for now.
riscv_cpu_validate_set_extensions() is kept public because it's used by
csr.c in write_misa().
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20230925175709.35696-4-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
As per ISA:
"For CSRRWI, if rd=x0, then the instruction shall not read the CSR and
shall not cause any of the side effects that might occur on a CSR read."
trans_csrrwi() and trans_csrrw() call do_csrw() if rd=x0, do_csrw() calls
riscv_csrrw_do64(), via helper_csrw() passing NULL as *ret_value.
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20230808090914.17634-1-nikita.shubin@maquefel.me>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
According to the new spec, when vsiselect has a reserved value, attempts
from M-mode or HS-mode to access vsireg, or from VS-mode to access
sireg, should preferably raise an illegal instruction exception.
Signed-off-by: Tommy Wu <tommy.wu@sifive.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Message-ID: <20230816061647.600672-1-tommy.wu@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The Svadu specification updated the name of the *envcfg bit from
HADE to ADUE.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20230816141916.66898-1-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
These are WARL fields - zero out the bits for unavailable counters and
special case the TM bit in mcountinhibit which is hardwired to zero.
This patch achieves this by modifying the value written so that any use
of the field will see the correctly masked bits.
Tested by modifying OpenSBI to write max value to these CSRs and upon
subsequent read the appropriate number of bits for number of PMUs is
enabled and the TM bit is zero in mcountinhibit.
Signed-off-by: Rob Bradford <rbradford@rivosinc.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Message-ID: <20230802124906.24197-1-rbradford@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
"qemu/main-loop.h" declares functions related to QEMU's
main loop mutex, which these files don't access. Remove
the unused "qemu/main-loop.h" header.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230828221314.18435-8-philmd@linaro.org>
Pointer mask is also affected by MPRV which means cur_pmbase/pmmask
should also take MPRV into consideration. As pointer mask for instruction
is not supported currently, so we can directly update cur_pmbase/pmmask
based on address related mode and xlen affected by MPRV now.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-Id: <20230614032547.35895-3-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
SXL is initialized as env->misa_mxl which is also the mxl value.
So we can just remain it unchanged to keep it read-only.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230603134236.15719-4-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
MPV and GVA bits are added by hypervisor extension to mstatus
and mstatush (if MXLEN=32).
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230603134236.15719-3-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Implement the s/h/mstateen.fcsr bit as defined in the smstateen spec
and check for it when accessing the fcsr register and its fields.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230518175058.2772506-2-mchitale@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
write_mstatus() can only change current xl when in debug mode.
And we need update cur_pmmask/base in this case.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Message-Id: <20230524015933.17349-3-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
write_misa() must use as much common logic as possible. We want to open
code just the bits that are exclusive to the CSR write operation and TCG
internals.
Our validation is done with riscv_cpu_validate_set_extensions(), but we
need a small tweak first. When enabling RVG we're doing:
env->misa_ext |= RVI | RVM | RVA | RVF | RVD;
env->misa_ext_mask = env->misa_ext;
This works fine for realize() time but this can potentially overwrite
env->misa_ext_mask if we reutilize the function for write_misa().
Instead of doing misa_ext_mask = misa_ext, sum up the RVG extensions in
misa_ext_mask as well. This won't change realize() time behavior
(misa_ext_mask will be == misa_ext) and will ensure that write_misa()
won't change misa_ext_mask by accident.
After that, rewrite write_misa() to work as follows:
- mask the write using misa_ext_mask to avoid enabling unsupported
extensions;
- suppress RVC if the next insn isn't aligned;
- disable RVG if any of RVG dependencies are being disabled by the user;
- assign env->misa_ext and run riscv_cpu_validate_set_extensions(). On
error, rollback env->misa_ext to its original value, logging a
GUEST_ERROR to inform the user about the failed write;
- handle RVF and MSTATUS_FS and continue as usual.
Let's keep write_misa() as experimental for now until this logic gains
enough mileage.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-Id: <20230517135714.211809-12-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When reading a non-existent CSR QEMU should raise illegal instruction
exception, but currently it just exits due to the g_assert() check.
This actually reverts commit 0ee342256a.
Some comments are also added to indicate that predicate() must be
provided for an implemented CSR.
Reported-by: Fei Wu <fei2.wu@intel.com>
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Message-Id: <20230417043054.3125614-1-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Incorporate the virt_enabled and MPV checks into the cpu_mmu_index
function, so we don't have to keep doing it within tlb_fill and
subroutines. This also elides a flush on changes to MPV.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Tested-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-Id: <20230325105429.1142530-17-richard.henderson@linaro.org>
Message-Id: <20230412114333.118895-17-richard.henderson@linaro.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Kernel needs to access user mode memory e.g. during syscalls, the window
is usually opened up for a very limited time through MSTATUS.SUM, the
overhead is too much if tlb_flush() gets called for every SUM change.
This patch creates a separate MMU index for S+SUM, so that it's not
necessary to flush tlb anymore when SUM changes. This is similar to how
ARM handles Privileged Access Never (PAN).
Result of 'pipe 10' from unixbench boosts from 223656 to 1705006. Many
other syscalls benefit a lot from this too.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Fei Wu <fei2.wu@intel.com>
Message-Id: <20230324054154.414846-3-fei2.wu@intel.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Tested-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-Id: <20230325105429.1142530-8-richard.henderson@linaro.org>
Message-Id: <20230412114333.118895-8-richard.henderson@linaro.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The pointer masking is the only extension that directly use status.
The vector or float extension uses the status in an indirect way.
Replace the pointer masking extension special status fields with
the general status.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Message-Id: <20230324143031.1093-3-zhiwei_liu@linux.alibaba.com>
[rth: Add a typedef for the enum]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Tested-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-Id: <20230325105429.1142530-3-richard.henderson@linaro.org>
Message-Id: <20230412114333.118895-3-richard.henderson@linaro.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
- Trap satp/hgatp accesses from HS-mode when MSTATUS.TVM is enabled.
- Trap satp accesses from VS-mode when HSTATUS.VTVM is enabled.
- Raise RISCV_EXCP_ILLEGAL_INST when U-mode executes SFENCE.VMA/SINVAL.VMA.
- Raise RISCV_EXCP_VIRT_INSTRUCTION_FAULT when VU-mode executes
SFENCE.VMA/SINVAL.VMA or VS-mode executes SFENCE.VMA/SINVAL.VMA with
HSTATUS.VTVM enabled.
- Raise RISCV_EXCP_VIRT_INSTRUCTION_FAULT when VU-mode executes
HFENCE.GVMA/HFENCE.VVMA/HINVAL.GVMA/HINVAL.VVMA.
Signed-off-by: Yi Chen <chenyi2000@zju.edu.cn>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230406101559.39632-1-chenyi2000@zju.edu.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
mstatus.MPP field is a WARL field since priv version 1.11, so we
remain it unchanged if an invalid value is written into it. And
after this, RVH shouldn't be passed to riscv_cpu_set_mode().
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230407014743.18779-4-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Fix lines with over 80 characters for both code and comments.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-Id: <20230405085813.40643-5-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Fix formats for multi-lines comments.
Add spaces around single line comments(after "/*" and before "*/").
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-Id: <20230405085813.40643-4-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Directly use env->virt_enabled instead.
Suggested-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-Id: <20230405085813.40643-2-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Add encode, trans* functions and helper functions support for Zcmt
instrutions.
Add support for jvt csr.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230307081403.61950-8-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Remove RISCVCPU argument, and get cfg infomation from CPURISCVState
directly.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230309071329.45932-5-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Use CPURISCVState as argument directly in riscv_cpu_update_mip and
riscv_timer_write_timecmp, since type converts from CPURISCVState to
RISCVCPU in many caller of them and then back to CPURISCVState in them.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-Id: <20230309071329.45932-4-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Use riscv_cpu_cfg(env) instead of env_archcpu().cfg.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-Id: <20230309071329.45932-2-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This aids subsystems (like gdbstub) that want to trigger a flush
without pulling target specific headers.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230302190846.2593720-8-alex.bennee@linaro.org>
Message-Id: <20230303025805.625589-8-richard.henderson@linaro.org>
RISC-V specifies multiple sizes for addressable memory and Linux probes for
the machine's support at startup via the satp CSR register (done in
csr.c:validate_vm).
As per the specification, sv64 must support sv57, which in turn must
support sv48...etc. So we can restrict machine support by simply setting the
"highest" supported mode and the bare mode is always supported.
You can set the satp mode using the new properties "sv32", "sv39", "sv48",
"sv57" and "sv64" as follows:
-cpu rv64,sv57=on # Linux will boot using sv57 scheme
-cpu rv64,sv39=on # Linux will boot using sv39 scheme
-cpu rv64,sv57=off # Linux will boot using sv48 scheme
-cpu rv64 # Linux will boot using sv57 scheme by default
We take the highest level set by the user:
-cpu rv64,sv48=on,sv57=on # Linux will boot using sv57 scheme
We make sure that invalid configurations are rejected:
-cpu rv64,sv39=off,sv48=on # sv39 must be supported if higher modes are
# enabled
We accept "redundant" configurations:
-cpu rv64,sv48=on,sv57=off # Linux will boot using sv48 scheme
And contradictory configurations:
-cpu rv64,sv48=on,sv48=off # Linux will boot using sv39 scheme
Co-Developed-by: Ludovic Henry <ludovic@rivosinc.com>
Signed-off-by: Ludovic Henry <ludovic@rivosinc.com>
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Message-ID: <20230303131252.892893-4-alexghiti@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
This array is actually used as a boolean so swap its current char type
to a boolean and at the same time, change the type of validate_vm to
bool since it returns valid_vm_1_10_[32|64].
Suggested-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Message-ID: <20230303131252.892893-3-alexghiti@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Daniel Henrique Barboza <dbarboza@ventanamicro.com> says:
These cleanups were suggested by LIU Zhiwei during the review of
d3e6d5762b ("Merge patch series "make write_misa a no-op and FEATURE_*
cleanups"").
* b4-shazam-merge:
target/riscv/csr.c: avoid env_archcpu() usages when reading RISCVCPUConfig
target/riscv/csr.c: use riscv_cpu_cfg() to avoid env_cpu() pointers
target/riscv/csr.c: simplify mctr()
target/riscv/csr.c: use env_archcpu() in ctr()
Message-ID: <20230224174520.92490-1-dbarboza@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Retrieving the CPU pointer using env_archcpu() just to access cpu->cfg
can be avoided by using riscv_cpu_cfg().
Suggested-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20230224174520.92490-5-dbarboza@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
A common trend in this file is to retrieve a RISCVCPU pointer by first
retrieving a CPUState pointer via env_cpu(). The CPU pointer is used
only to access the RISCVCPUConfig object and nothing else.
Let's use riscv_cpu_cfg() to access what we need directly without these
2 pointers.
Suggested-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20230224174520.92490-4-dbarboza@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Use riscv_cpu_cfg() to retrieve pmu_num.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20230224174520.92490-3-dbarboza@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
We don't need to use env_cpu() and CPUState().
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20230224174520.92490-2-dbarboza@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Weiwei Li <liweiwei@iscas.ac.cn> says:
This patchset adds support svadu extension. It also fixes some
relationship between *envcfg fields and Svpbmt/Sstc extensions.
Specification for Svadu extension can be found in:
https://github.com/riscv/riscv-svadu
* b4-shazam-merge:
target/riscv: Export Svadu property
target/riscv: Add *envcfg.HADE related check in address translation
target/riscv: Add *envcfg.PBMTE related check in address translation
target/riscv: Add csr support for svadu
target/riscv: Fix the relationship of PBMTE/STCE fields between menvcfg and henvcfg
target/riscv: Fix the relationship between menvcfg.PBMTE/STCE and Svpbmt/Sstc extensions
Message-ID: <20230224040852.37109-1-liweiwei@iscas.ac.cn>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Add ext_svadu property
Add HADE field in *envcfg:
* menvcfg.HADE is read-only zero if Svadu is not implemented.
* henvcfg.HADE is read-only zero if menvcfg.HADE is zero.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20230224040852.37109-4-liweiwei@iscas.ac.cn>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
henvcfg.PBMTE/STCE are read-only zero if menvcfg.PBMTE/STCE are zero.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20230224040852.37109-3-liweiwei@iscas.ac.cn>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
menvcfg.PBMTE/STCE are read-only zero if Svpbmt/Sstc are not implemented.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20230224040852.37109-2-liweiwei@iscas.ac.cn>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Bin Meng <bmeng@tinylab.org> says:
At present gdbstub reports an incorrect / incomplete CSR list in the
target description XML, for example:
- menvcfg is reported in 'sifive_u' machine
- fcsr is missing in a F/D enabled processor
The issue is caused by:
- priv spec version check is missing when reporting CSRs
- CSR predicate() routine is called without turning on the debugger flag
* b4-shazam-merge:
target/riscv: Group all predicate() routines together
target/riscv: Drop priv level check in mseccfg predicate()
target/riscv: Allow debugger to access sstc CSRs
target/riscv: Allow debugger to access {h, s}stateen CSRs
target/riscv: Allow debugger to access seed CSR
target/riscv: Allow debugger to access user timer and counter CSRs
target/riscv: gdbstub: Drop the vector CSRs in riscv-vector.xml
target/riscv: gdbstub: Turn on debugger mode before calling CSR predicate()
target/riscv: Avoid reporting odd-numbered pmpcfgX in the CSR XML for RV64
target/riscv: Simplify getting RISCVCPU pointer from env
target/riscv: Simplify {read, write}_pmpcfg() a little bit
target/riscv: Use 'bool' type for read_only
target/riscv: Coding style fixes in csr.c
target/riscv: gdbstub: Do not generate CSR XML if Zicsr is disabled
target/riscv: gdbstub: Minor change for better readability
target/riscv: Use g_assert() for the predicate() NULL check
target/riscv: Add some comments to clarify the priority policy of riscv_csrrw_check()
target/riscv: gdbstub: Check priv spec version before reporting CSR
Message-ID: <20230228104035.1879882-1-bmeng@tinylab.org>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Move sstc()/sstc32() to where all predicate() routines live, and
smstateen_acc_ok() to near {read,write}_xenvcfg().
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Message-ID: <20230228104035.1879882-19-bmeng@tinylab.org>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
riscv_csrrw_check() already does the generic privilege level check
hence there is no need to do the specific M-mode access check in
the mseccfg predicate().
With this change debugger can access the mseccfg CSR anytime.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Message-ID: <20230228104035.1879882-18-bmeng@tinylab.org>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
