Fix issue reported by Coverity.
Signed-off-by: Axel Heider <axel.heider@hensoldt.net>
Message-id: 168070611775.20412.2883242077302841473-1@git.sr.ht
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds WDT to Allwinner-H3 and Orangepi-PC.
WDT is added as an overlay to the Timer module memory area.
Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20230326202256.22980-4-strahinja.p.jankovic@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds WDT to Allwinner-A10 and Cubieboard.
WDT is added as an overlay to the Timer module memory map.
Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20230326202256.22980-3-strahinja.p.jankovic@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds basic support for Allwinner WDT.
Both sun4i and sun6i variants are supported.
However, interrupt generation is not supported, so WDT can be used only to trigger system reset.
Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20230326202256.22980-2-strahinja.p.jankovic@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
One of the debug printfs in exynos4210_gcomp_find() will
access outside the 's->g_timer.reg.comp[]' array if there
was no active comparator and 'res' is -1. Add a conditional
to avoid this.
This doesn't happen in normal use because the debug printfs
are by default not compiled in.
Signed-off-by: Feng Jiang <jiangfeng@kylinos.cn>
Message-id: 20230404074506.112615-1-jiangfeng@kylinos.cn
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: Adjusted commit message to clarify that the overrun
only happens if you've enabled debug printfs]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230409200526.1156456-1-sw@weilnetz.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Last patches found:
- peter xu preempt channel fixes.
needed for backward compatibility with old machine types.
- lukas fix to get compress working again.
- fix ram on s390x. Get back to the old code, even when it shouldn't
be needed, but as it fails on s390x, just revert.
Later, Juan.
-----BEGIN PGP SIGNATURE-----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=kW3P
-----END PGP SIGNATURE-----
Merge tag 'migration-20230412-pull-request' of https://gitlab.com/juan.quintela/qemu into staging
Migration Pull request for 8.0
Last patches found:
- peter xu preempt channel fixes.
needed for backward compatibility with old machine types.
- lukas fix to get compress working again.
- fix ram on s390x. Get back to the old code, even when it shouldn't
be needed, but as it fails on s390x, just revert.
Later, Juan.
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEGJn/jt6/WMzuA0uC9IfvGFhy1yMFAmQ3HgQACgkQ9IfvGFhy
# 1yPXGQ/+Pf6HepNUlIr7naYOcpRriXPQF+q1zqo74F9fy2vrGcwJOI6qmRTjsX4E
# 9KgXipOz7+b5wSemF7PDKcnBiwyt6UHCH+XXe0h4TpyuORbtABKRgtOhA1/sa84D
# HnKp0TwImpAO26tzPa7u49aau/EEVBKAzFVcyn4w56S9qiDWicOpd5kG0CJBIsMJ
# Mnvy5fXaqQRewnKiwFoJGWfyhzEToDO6Z/SkT5xYON94P+eiM2xMwXOC5WcGfmY7
# wFGDB+SuyEP8TTn7mV0mmnlFjYe4G07hVARHSDFX3ho4b6q5F+WzfW095G6QKiu9
# n3Pzr7IBGX3sgetPtYwOwGsE9JrfHMFzBRxQZZwq5GSmjk7+agkbXmV7RyV82EYs
# KYOhuNF91ca0qvCrGA/eGbbJqVrd7SR5FhS4SQ7oKd5n2au/ZHoKwAgm5lBdcvES
# 2TB0MBN1s0JPh6KMV8tPB2miZyqPRa++oA8qIX7Asoe1X4xVT1FwiDaFL8TO8i2A
# 7uBis3KLZqOHC6dAiXlCDtaADAWgQxjcdoS1l8jTF6MgBSe+zQhXG+pcIDuSiV9N
# WfDiUPY97iqPTvpzdz3Is+LbBax2uY5ZR05KSdmCBpIgfvSWMqXtwRydclt6G5h7
# ZiOcTwrgMpXdbhdsFZTqVWAJG2sTkj4TA+IezVpXzPeQNLZ+T8k=
# =kW3P
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 12 Apr 2023 22:09:24 BST
# gpg: using RSA key 1899FF8EDEBF58CCEE034B82F487EF185872D723
# gpg: Good signature from "Juan Quintela <quintela@redhat.com>" [full]
# gpg: aka "Juan Quintela <quintela@trasno.org>" [full]
# Primary key fingerprint: 1899 FF8E DEBF 58CC EE03 4B82 F487 EF18 5872 D723
* tag 'migration-20230412-pull-request' of https://gitlab.com/juan.quintela/qemu:
migration: fix ram_state_pending_exact()
migration/ram.c: Fix migration with compress enabled
migration: Recover behavior of preempt channel creation for pre-7.2
migration: Fix potential race on postcopy_qemufile_src
io: tls: Inherit QIO_CHANNEL_FEATURE_SHUTDOWN on server side
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Coverity spotted a double-free (CID 1508254); we g_string_free(path) and
then for some reason immediately call free(path) too.
We should just use g_autoptr() for it anyway, which simplifies the code
a bit.
Fixes: 7a8a749da7 ("hw/xen: Move xenstore_store_pv_console_info to xen_console.c")
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
postcopy_qemufile_src object should be owned by one thread, either the main
thread (e.g. when at the beginning, or at the end of migration), or by the
return path thread (when during a preempt enabled postcopy migration). If
that's not the case the access to the object might be racy.
postcopy_preempt_shutdown_file() can be potentially racy, because it's
called at the end phase of migration on the main thread, however during
which the return path thread hasn't yet been recycled; the recycle happens
in await_return_path_close_on_source() which is after this point.
It means, logically it's posslbe the main thread and the return path thread
are both operating on the same qemufile. While I don't think qemufile is
thread safe at all.
postcopy_preempt_shutdown_file() used to be needed because that's where we
send EOS to dest so that dest can safely shutdown the preempt thread.
To avoid the possible race, remove this only place that a race can happen.
Instead we figure out another way to safely close the preempt thread on
dest.
The core idea during postcopy on deciding "when to stop" is that dest will
send a postcopy SHUT message to src, telling src that all data is there.
Hence to shut the dest preempt thread maybe better to do it directly on
dest node.
This patch proposed such a way that we change postcopy_prio_thread_created
into PreemptThreadStatus, so that we kick the preempt thread on dest qemu
by a sequence of:
mis->preempt_thread_status = PREEMPT_THREAD_QUIT;
qemu_file_shutdown(mis->postcopy_qemufile_dst);
While here shutdown() is probably so far the easiest way to kick preempt
thread from a blocked qemu_get_be64(). Then it reads preempt_thread_status
to make sure it's not a network failure but a willingness to quit the
thread.
We could have avoided that extra status but just rely on migration status.
The problem is postcopy_ram_incoming_cleanup() is just called early enough
so we're still during POSTCOPY_ACTIVE no matter what.. So just make it
simple to have the status introduced.
One flag x-preempt-pre-7-2 is added to keep old pre-7.2 behaviors of
postcopy preempt.
Fixes: 9358982744 ("migration: Send requested page directly in rp-return thread")
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The iocb (and the allocated memory to hold LBA ranges) leaks if reading
the LBA ranges fails.
Fix this by adding a free and an unref of the iocb.
Reported-by: Coverity (CID 1508281)
Fixes: d7d1474fd8 ("hw/nvme: reimplement dsm to allow cancellation")
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Coverity reports a memory leak of memory when parsing ruhids at
namespace initialization. Since this is just working memory, not needed
beyond the scope of the functions, fix this by adding a g_autofree
annotation.
Reported-by: Coverity (CID 1507979)
Fixes: 73064edfb8 ("hw/nvme: flexible data placement emulation")
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
In commit 8461bfdca9 we added the TYPE_AW_I2C_SUN6I, which is a
minor variant of the TYPE_AW_I2C device. However, we didn't quite
get the class hierarchy right. We made the new TYPE_AW_I2C_SUN6I a
subclass of TYPE_SYS_BUS_DEVICE, which means that you can't validly
use a pointer to this object via the AW_I2C() cast macro, which
insists on having something that is an instance of TYPE_AW_I2C or
some subclass of that type.
This only causes a problem if QOM cast macro debugging is enabled;
that is supposed to be on by default, but a mistake in the meson
conversion in commit c55cf6ab03 meant that it ended up disabled by
default, and we didn't catch this bug.
Fix the problem by arranging the classes in the same way we do for
TYPE_PL011 and TYPE_PL011_LUMINARY in hw/char/pl011.c -- make the
variant class be a subclass of the "normal" version of the device.
This was reported in
https://gitlab.com/qemu-project/qemu/-/issues/1586 but this fix alone
isn't sufficient, as there is a separate cast-related issue in the
CXL code in pci_expander_bridge.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
This reverts commit 6da2434186
("memory: Optimize replay of guest mapping").
This change breaks the mps3-an547 board under TCG (and
probably other TCG boards using an IOMMU), which now
assert:
$ ./build/x86/qemu-system-arm --machine mps3-an547 -serial stdio
-kernel /tmp/an547-mwe/build/test.elf
qemu-system-arm: ../../softmmu/memory.c:1903:
memory_region_register_iommu_notifier: Assertion `n->end <=
memory_region_size(mr)' failed.
This is because tcg_register_iommu_notifier() registers
an IOMMU notifier which covers the entire address space,
so the assertion added in this commit is not correct.
For the 8.0 release, just revert this commit as it is
only an optimization.
Fixes: 6da2434186 ("memory: Optimize replay of guest mapping")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 917c1c552b2d1b732f9a86c6a90684c3a5e4cada.1680640587.git.mst@redhat.com
-----BEGIN PGP SIGNATURE-----
iLMEAAEIAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZCwLXQAKCRBAov/yOSY+
3zwUA/9d2ddHxGEBTMyF45bzc9JxRF6HoILAwMLsmPWqspPgKdGuviMVewJLt5m8
V75/BC6Sn9rhdkXALvZMRV6WQ2A16pByUaQtMYAXVsIoV8Mrpvm4GwJD1E0/cy5Q
TwDTzpDfys9WsTVj0QlCPjp0JW+KA7Y6ArMUUCdCz41L2r7mPA==
=ovw7
-----END PGP SIGNATURE-----
Merge tag 'pull-loongarch-20230404' of https://gitlab.com/gaosong/qemu into staging
pull-loongarch-20230404
# -----BEGIN PGP SIGNATURE-----
#
# iLMEAAEIAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZCwLXQAKCRBAov/yOSY+
# 3zwUA/9d2ddHxGEBTMyF45bzc9JxRF6HoILAwMLsmPWqspPgKdGuviMVewJLt5m8
# V75/BC6Sn9rhdkXALvZMRV6WQ2A16pByUaQtMYAXVsIoV8Mrpvm4GwJD1E0/cy5Q
# TwDTzpDfys9WsTVj0QlCPjp0JW+KA7Y6ArMUUCdCz41L2r7mPA==
# =ovw7
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 04 Apr 2023 12:34:53 BST
# gpg: using RSA key B8FF1DA0D2FDCB2DA09C6C2C40A2FFF239263EDF
# gpg: Good signature from "Song Gao <m17746591750@163.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B8FF 1DA0 D2FD CB2D A09C 6C2C 40A2 FFF2 3926 3EDF
* tag 'pull-loongarch-20230404' of https://gitlab.com/gaosong/qemu:
target/loongarch: Enables plugins to get instruction codes
hw/loongarch/virt: Fix virt_to_phys_addr function
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The virt addr should mask TARGET_PHYS_ADDR_SPACE_BITS to
get the phys addr, and this is used by loading kernel elf.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230327112313.3042829-1-zhaotianrui@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
At this moment, arm_load_dtb() can free machine->fdt when
binfo->dtb_filename is NULL. If there's no 'dtb_filename', 'fdt' will be
retrieved by binfo->get_dtb(). If get_dtb() returns machine->fdt, as is
the case of machvirt_dtb() from hw/arm/virt.c, fdt now has a pointer to
machine->fdt. And, in that case, the existing g_free(fdt) at the end of
arm_load_dtb() will make machine->fdt point to an invalid memory region.
Since monitor command 'dumpdtb' was introduced a couple of releases
ago, running it with any ARM machine that uses arm_load_dtb() will
crash QEMU.
Let's enable all arm_load_dtb() callers to use dumpdtb properly. Instead
of freeing 'fdt', assign it back to ms->fdt.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Fixes: bf353ad555 ("qmp/hmp, device_tree.c: introduce dumpdtb")
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-id: 20230328165935.1512846-1-armbru@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Devices models calling pmbus_send_string can't be relied upon to
send a non-zero pointer. This logs an error and doesn't segfault.
Reviewed-by: Patrick Venture <venture@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230322175513.1550412-5-titusr@google.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
145e2198d7 ("hw/mips/gt64xxx_pci: Endian-swap using PCI_HOST_BRIDGE
MemoryRegionOps") converted CFGADDR/CFGDATA registers to use
PCI_HOST_BRIDGE's accessor facility and enabled byte swap for both
CFGADDR/CFGDATA register.
However CFGADDR as a ISD internal register is not controlled by
MByteSwap bit, it follows endian of all other ISD register, which
means it ties to little endian.
Move mapping of CFGADDR out of gt64120_update_pci_cfgdata_mapping
to disable endian-swapping.
Fixes: 145e2198d7 ("hw/mips/gt64xxx_pci: Endian-swap using PCI_HOST_BRIDGE MemoryRegionOps")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Message-Id: <20230223161958.48696-1-jiaxun.yang@flygoat.com>
[PMD: !!! Note this only fixes little-endian hosts !!! ]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Version: GnuPG v1
iQEcBAABAgAGBQJkIncaAAoJEO8Ells5jWIR6bgH/icQAN1a0PBHh2lujmob8KvE
IZ0KYuJMDcA8HFdhnzxPPKj7/77AM1DgmrmVwqLKTr6j64CZYr2Uc0yeyPa0f/0Y
TtePW70bjoUkRm/dDdFe32xViO4O33pGQia6olR6QwmfdDbBBJjAucmlep8NClrh
EooQ2WfXPBqrC6ckKZ7vEvgKV2sDl2XxYIr3kU3MiB4j4b1lrGHE+XSv7cXOC+at
G2vYqbimipZstHZCJYeB5tRz+FXbAI3ZNCGtYpxeVyabrlHS+n+X+gttaswcvVIF
ln6yidVGg/Ot3bi0qiV1WihpqNCWO0ghhf7wIEubAIIJlnE5hXULF4uFVfz+rRE=
=HjJv
-----END PGP SIGNATURE-----
Merge tag 'net-pull-request' of https://github.com/jasowang/qemu into staging
# -----BEGIN PGP SIGNATURE-----
# Version: GnuPG v1
#
# iQEcBAABAgAGBQJkIncaAAoJEO8Ells5jWIR6bgH/icQAN1a0PBHh2lujmob8KvE
# IZ0KYuJMDcA8HFdhnzxPPKj7/77AM1DgmrmVwqLKTr6j64CZYr2Uc0yeyPa0f/0Y
# TtePW70bjoUkRm/dDdFe32xViO4O33pGQia6olR6QwmfdDbBBJjAucmlep8NClrh
# EooQ2WfXPBqrC6ckKZ7vEvgKV2sDl2XxYIr3kU3MiB4j4b1lrGHE+XSv7cXOC+at
# G2vYqbimipZstHZCJYeB5tRz+FXbAI3ZNCGtYpxeVyabrlHS+n+X+gttaswcvVIF
# ln6yidVGg/Ot3bi0qiV1WihpqNCWO0ghhf7wIEubAIIJlnE5hXULF4uFVfz+rRE=
# =HjJv
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 28 Mar 2023 06:11:54 BST
# gpg: using RSA key EF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* tag 'net-pull-request' of https://github.com/jasowang/qemu:
igb: respect VMVIR and VMOLR for VLAN
igb: implement VF Tx and Rx stats
igb: respect E1000_VMOLR_RSSE
igb: check oversized packets for VMDq
igb: implement VFRE and VFTE registers
igb: add ICR_RXDW
igb: handle PF/VF reset properly
MAINTAINERS: Add Sriram Yagnaraman as a igb reviewer
hw/net/net_tx_pkt: Align l3_hdr
hw/net/net_tx_pkt: Ignore ECN bit
igb: Fix DMA requester specification for Tx packet
igb: Save more Tx states
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for stripping/inserting VLAN for VFs.
Had to move CSUM calculation back into the for loop, since packet data
is pulled inside the loop based on strip VLAN decision for every VF.
net_rx_pkt_fix_l4_csum should be extended to accept a buffer instead for
igb. Work for a future patch.
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Please note that loopback counters for VM to VM traffic is not
implemented yet: VFGOTLBC, VFGPTLBC, VFGORLBC and VFGPRLBC.
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
RSS for VFs is only enabled if VMOLR[n].RSSE is set.
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
IGB uses RXDW ICR bit to indicate that rx descriptor has been written
back. This is the same as RXT0 bit in older HW.
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Use PFRSTD to reset RSTI bit for VFs, and raise VFLRE interrupt when VF
is reset.
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Align the l3_hdr member of NetTxPkt by defining it as a union of
ip_header, ip6_header, and an array of octets.
Fixes: e263cd49c7 ("Packet abstraction for VMWARE network devices")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1544
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
No segmentation should be performed if gso type is
VIRTIO_NET_HDR_GSO_NONE even if ECN bit is set.
Fixes: e263cd49c7 ("Packet abstraction for VMWARE network devices")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1544
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
igb used to specify the PF as DMA requester when reading Tx packets.
This made Tx requests from VFs to be performed on the address space of
the PF, defeating the purpose of SR-IOV. Add some logic to change the
requester depending on the queue, which can be assigned to a VF.
Fixes: 3a977deebe ("Intrdocue igb device emulation")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The current implementation of igb uses only part of a advanced Tx
context descriptor and first data descriptor because it misses some
features and sniffs the trait of the packet instead of respecting the
packet type specified in the descriptor. However, we will certainly
need the entire Tx context descriptor when we update igb to respect
these ignored fields. Save the entire context descriptor and first
data descriptor except the buffer address to prepare for such a change.
This also introduces the distinction of contexts with different
indexes, which was not present in e1000e but in igb.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Even if the host is somehow using compare to do compare-and-write, the
host should be notified immediately about the compare failure and not
have to wait for the driver to potentially retry the command.
Fixes: 0a384f923f ("hw/block/nvme: add compare command")
Reported-by: Jim Harris <james.r.harris@intel.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Since the nvme_blk_read/write are used by both the data and metadata
portions of the IO, it can't have the 512B alignment requirement.
Without this change any metadata transfer, which length isn't a multiple
of 512B and which is bigger than 512B, will result in only a partial
transfer.
Signed-off-by: Mateusz Kozlowski <kozlowski.mateuszpl@gmail.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
As the Xen backend operations were abstracted out into a function table to
allow for internally emulated Xen support, we missed the xen_init_pv()
code path which also needs to install the operations for the true Xen
libraries. Add the missing call to setup_xen_backend_ops().
Fixes: b6cacfea0b ("hw/xen: Add evtchn operations to allow redirection to internal emulation")
Reported-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Tested-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <5dfb65342d4502c1ce2f890c97cff20bf25b3860.camel@infradead.org>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Bring the block files in line with the QEMU coding style, with spaces
for indentation. This patch partially resolves the issue 371.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/371
Signed-off-by: Yeqi Fu <fufuyqqqqqq@gmail.com>
Message-Id: <20230314095001.13801-1-fufuyqqqqqq@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Bring the block files in line with the QEMU coding style, with spaces
for indentation. This patch partially resolves the issue 371.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/371
Signed-off-by: Yeqi Fu <fufuyqqqqqq@gmail.com>
Message-Id: <20230315043229.62100-1-fufuyqqqqqq@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This had been pulled in via qemu/plugin.h from hw/core/cpu.h,
but that will be removed.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230310195252.210956-5-richard.henderson@linaro.org>
[AJB: add various additional cases shown by CI]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230315174331.2959-15-alex.bennee@linaro.org>
Reviewed-by: Emilio Cota <cota@braap.org>
The i.MX USB Phy driver does not check register ranges, resulting in out of
bounds accesses if an attempt is made to access non-existing PHY registers.
Add range check and conditionally report bad accesses to fix the problem.
While at it, also conditionally log attempted writes to non-existing or
read-only registers.
Reported-by: Qiang Liu <cyruscyliu@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Qiang Liu <cyruscyliu@gmail.com>
Message-id: 20230316234926.208874-1-linux@roeck-us.net
Link: https://gitlab.com/qemu-project/qemu/-/issues/1408
Fixes: 0701a5efa0 ("hw/usb: Add basic i.MX USB Phy support")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The cadence UART attempts to avoid allowing the guest to set invalid
baud rate register values in the uart_write() function. However it
does the "mask to the size of the register field" and "check for
invalid values" in the wrong order, which means that a malicious
guest can get a bogus value into the register by setting also some
high bits in the value, and cause QEMU to crash by division-by-zero.
Do the mask before the bounds check instead of afterwards.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1493
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar@zeroasic.com>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Qiang Liu <cyruscyliu@gmail.com>
Message-id: 20230314170804.1196232-1-peter.maydell@linaro.org
Bring the files in line with the QEMU coding style, with spaces
for indentation.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/378
Signed-off-by: Yeqi Fu <fufuyqqqqqq@gmail.com>
Message-Id: <20230315032649.57568-1-fufuyqqqqqq@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
A Linux guest will perform IRQ migration after the IRQ has happened,
updating the RTE to point to the new destination CPU and then unmasking
the interrupt.
However, when the guest updates the RTE, ioapic_mem_write() calls
ioapic_service(), which redelivers the pending level interrupt via
kvm_set_irq(), *before* calling ioapic_update_kvm_routes() which sets
the new target CPU.
Thus, the IRQ which is supposed to go to the new target CPU is instead
misdelivered to the previous target. An example where the guest kernel
is attempting to migrate from CPU#2 to CPU#0 shows:
xenstore_read tx 0 path control/platform-feature-xs_reset_watches
ioapic_set_irq vector: 11 level: 1
ioapic_set_remote_irr set remote irr for pin 11
ioapic_service: trigger KVM IRQ 11
[ 0.523627] The affinity mask was 0-3 and the handler is on 2
ioapic_mem_write ioapic mem write addr 0x0 regsel: 0x27 size 0x4 val 0x26
ioapic_update_kvm_routes: update KVM route for IRQ 11: fee02000 8021
ioapic_mem_write ioapic mem write addr 0x10 regsel: 0x26 size 0x4 val 0x18021
xenstore_reset_watches
ioapic_set_irq vector: 11 level: 1
ioapic_mem_read ioapic mem read addr 0x10 regsel: 0x26 size 0x4 retval 0x1c021
[ 0.524569] ioapic_ack_level IRQ 11 moveit = 1
ioapic_eoi_broadcast EOI broadcast for vector 33
ioapic_clear_remote_irr clear remote irr for pin 11 vector 33
ioapic_mem_write ioapic mem write addr 0x0 regsel: 0x26 size 0x4 val 0x26
ioapic_mem_read ioapic mem read addr 0x10 regsel: 0x26 size 0x4 retval 0x18021
[ 0.525235] ioapic_finish_move IRQ 11 calls irq_move_masked_irq()
[ 0.526147] irq_do_set_affinity for IRQ 11, 0
[ 0.526732] ioapic_set_affinity for IRQ 11, 0
[ 0.527330] ioapic_setup_msg_from_msi for IRQ11 target 0
ioapic_mem_write ioapic mem write addr 0x0 regsel: 0x26 size 0x4 val 0x27
ioapic_mem_write ioapic mem write addr 0x10 regsel: 0x27 size 0x4 val 0x0
ioapic_mem_write ioapic mem write addr 0x0 regsel: 0x27 size 0x4 val 0x26
ioapic_mem_write ioapic mem write addr 0x10 regsel: 0x26 size 0x4 val 0x18021
[ 0.527623] ioapic_set_affinity returns 0
[ 0.527623] ioapic_finish_move IRQ 11 calls unmask_ioapic_irq()
ioapic_mem_write ioapic mem write addr 0x0 regsel: 0x26 size 0x4 val 0x26
ioapic_mem_write ioapic mem write addr 0x10 regsel: 0x26 size 0x4 val 0x8021
ioapic_set_remote_irr set remote irr for pin 11
ioapic_service: trigger KVM IRQ 11
ioapic_update_kvm_routes: update KVM route for IRQ 11: fee00000 8021
[ 0.529571] The affinity mask was 0 and the handler is on 2
[ xenstore_watch path memory/target token FFFFFFFF92847D40
There are no other code paths in ioapic_mem_write() which need the KVM
IRQ routing table to be updated, so just shift the call from the end
of the function to happen right before the call to ioapic_service()
and thus deliver the re-enabled IRQ to the right place.
Alternative fixes might have been just to remove the part in
ioapic_service() which delivers the IRQ via kvm_set_irq() because
surely delivering as MSI ought to work just fine anyway in all cases?
That code lacks a comment justifying its existence.
Or maybe in the specific case shown in the above log, it would have
sufficed for ioapic_update_kvm_routes() to update the route *even*
when the IRQ is masked. It's not like it's actually going to get
triggered unless QEMU deliberately does so, anyway? But that only
works because the target CPU happens to be in the high word of the
RTE; if something in the *low* word (vector, perhaps) was changed
at the same time as the unmask, we'd still trigger with stale data.
Fixes: 15eafc2e60 "kvm: x86: add support for KVM_CAP_SPLIT_IRQCHIP"
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20230308111952.2728440-2-dwmw2@infradead.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The scancodes for the Lang1 and Lang2 keys (i.e. Hangeul, Hanja) are
special since they already have the 0x80 bit set which is commonly used
to indicate a key release in AT set 1. Reportedly, real hardware does
not send a key release scancode. So, skip sending a release for these
keys. This ensures that Windows behaves correctly and interprets it as a
single keypress rather than two consecutive keypresses.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
The naming is more conventional in QEMU.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Use a close() wrapper instead, so that we don't need to worry about
closesocket() vs close() anymore, let's hope.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Message-Id: <20230221124802.4103554-17-marcandre.lureau@redhat.com>
Several features that landed at the last possible moment:
Passthrough HDM decoder emulation
Refactor cryptodev
RAS error emulation and injection
acpi-index support on non-hotpluggable slots
Dynamically switch to vhost shadow virtqueues at vdpa net migration
Plus a couple of bugfixes that look important to have in the release.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmQJ8TYPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRp37YIAMpQA5/ddmKKz/ABtBMHB5JX/SVYcG+1xkBR
j9IFYusOfmmDfmgAhv0Qxi9+Wik95lszVZUnphvocSGd0PXH47pK7yv9RZ1ttaYX
oAbXrGqXo8rUhl1ksQsJ8Iasj2di1BLP0byPuozbRkg1Kkz5TqRd9+hBqSBGEx21
tsP5708UVCDAriwYYO78Cx0ZasmB9bqqeom5FdEsg9sYJ5aElOOvitp9YO1p2xhU
gRvhD+k/aqNi+mfOUF7qGDBanxKgx75VV/KU1cjjS9R1vNtwRhfc/26PBrROY00a
wkZWnAxmzDFKRS6cEfeb+eDGEVjC3IqLAjcFeuAIT/78CwdvIiY=
=e1yv
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: features, fixes
Several features that landed at the last possible moment:
Passthrough HDM decoder emulation
Refactor cryptodev
RAS error emulation and injection
acpi-index support on non-hotpluggable slots
Dynamically switch to vhost shadow virtqueues at vdpa net migration
Plus a couple of bugfixes that look important to have in the release.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmQJ8TYPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRp37YIAMpQA5/ddmKKz/ABtBMHB5JX/SVYcG+1xkBR
# j9IFYusOfmmDfmgAhv0Qxi9+Wik95lszVZUnphvocSGd0PXH47pK7yv9RZ1ttaYX
# oAbXrGqXo8rUhl1ksQsJ8Iasj2di1BLP0byPuozbRkg1Kkz5TqRd9+hBqSBGEx21
# tsP5708UVCDAriwYYO78Cx0ZasmB9bqqeom5FdEsg9sYJ5aElOOvitp9YO1p2xhU
# gRvhD+k/aqNi+mfOUF7qGDBanxKgx75VV/KU1cjjS9R1vNtwRhfc/26PBrROY00a
# wkZWnAxmzDFKRS6cEfeb+eDGEVjC3IqLAjcFeuAIT/78CwdvIiY=
# =e1yv
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 09 Mar 2023 14:46:14 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (72 commits)
virtio: fix reachable assertion due to stale value of cached region size
hw/virtio/vhost-user: avoid using unitialized errp
hw/pxb-cxl: Support passthrough HDM Decoders unless overridden
hw/pci: Add pcie_count_ds_port() and pcie_find_port_first() helpers
hw/mem/cxl_type3: Add CXL RAS Error Injection Support.
hw/pci/aer: Make PCIE AER error injection facility available for other emulation to use.
hw/cxl: Fix endian issues in CXL RAS capability defaults / masks
hw/mem/cxl-type3: Add AER extended capability
hw/pci-bridge/cxl_root_port: Wire up MSI
hw/pci-bridge/cxl_root_port: Wire up AER
hw/pci/aer: Add missing routing for AER errors
hw/pci/aer: Implement PCI_ERR_UNCOR_MASK register
pcihp: add ACPI PCI hotplug specific is_hotpluggable_bus() callback
pcihp: move fields enabling hotplug into AcpiPciHpState
acpi: pci: move out ACPI PCI hotplug generator from generic slot generator build_append_pci_bus_devices()
acpi: pci: move BSEL into build_append_pcihp_slots()
acpi: pci: drop BSEL usage when deciding that device isn't hotpluggable
pci: move acpi-index uniqueness check to generic PCI device code
tests: acpi: update expected blobs
tests: acpi: add non zero function device with acpi-index on non-hotpluggble bus
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This change introduces emulation for the Intel 82576 adapter, AKA igb.
The details of the device will be provided by the documentation that
will follow this change.
This initial implementation of igb does not cover the full feature set,
but it selectively implements changes necessary to pass tests of Linut
Test Project, and Windows HLK. The below is the list of the implemented
changes; anything not listed here is not implemented:
New features:
- igb advanced descriptor handling
- Support of 16 queues
- SRRCTL.BSIZEPACKET register field
- SRRCTL.RDMTS register field
- Tx descriptor completion writeback
- Extended RA registers
- VMDq feature
- MRQC "Multiple Receive Queues Enable" register field
- DTXSWC.Loopback_en register field
- VMOLR.ROMPE register field
- VMOLR.AUPE register field
- VLVF.VLAN_id register field
- VLVF.VI_En register field
- VF
- Mailbox
- Reset
- Extended interrupt registers
- Default values for IGP01E1000 PHY registers
Removed features:
- e1000e extended descriptor
- e1000e packet split descriptor
- Legacy descriptor
- PHY register paging
- MAC Registers
- Legacy interrupt timer registers
- Legacy EEPROM registers
- PBA/POEM registers
- RSRPD register
- RFCTL.ACKDIS
- RCTL.DTYPE
- Copper PHY registers
Misc:
- VET register format
- ICR register format
Signed-off-by: Gal Hammer <gal.hammer@sap.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
[Jason: don't abort on msi(x)_init()]
Signed-off-by: Jason Wang <jasowang@redhat.com>
Some definitions in the header files are invalid for igb so extract
them to new header files to keep igb from referring to them.
Signed-off-by: Gal Hammer <gal.hammer@sap.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
