Instead of always assuming success for bdrv_aio_flush, actually do something
with the error. This respects the werror option and accordingly ignores the
error, reports it to the guest or stops the VM and retries after cont.
Ignoring the error is trivial, obviously. For stopping the VM and retrying
later old code can be reused, but we need to introduce a new status for "retry
a flush". For reporting to the guest, fortunately the same action is required
as for a failed read/write (status = DRDY | ERR, error = ABRT), so this code
can be reused as well.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
ATA does not only have the WCACHE enabled bit in identify word 85, but also
a WCACHE supported bit in word 82. While the Linux kernel is fine with the
latter at least hdparm also needs the former before correctly displaying
the cache settings. There's also a non-zero chance other operating systems
are more picky in their volatile write cache detection.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
IDE is a bit ugly in this respect. For one it doesn't really keep track
of a sector size - most of the protocol is in units of 512 bytes, and we
assume 2048 bytes for CDROMs which is correct most of the time.
Second IDE allocates an I/O buffer long before we know if we're dealing
with a CDROM or not, so increase the alignment for the io_buffer
unconditionally.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Fill in word 64 of IDENTIFY data to indicate support for PIO modes 3 and 4.
This allows NetBSD guests to use UltraDMA modes instead of just PIO mode 0.
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Changing block.h or blockdev.h resulted in recompiling most objects.
Move DriveInfo typedef and BlockInterfaceType enum definitions
to qemu-common.h and rearrange blockdev.h use to decrease churn.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The reason for not actually canceling the I/O is because with
virtualization and lots of VM running, a guest fs may mistake a
overload of the host, as an IDE timeout. So rather than canceling the
I/O, it's safer to wait I/O completion and simulate that the I/O has
completed just before the io cancellation was requested by the
guest. This way if ntfs or an app writes data without checking for
-EIO retval, and it thinks the write has succeeded, it's less likely
to run into troubles. Similar issues for reads.
Furthermore because the DMA operation is splitted into many synchronous
aio_read/write if there's more than one entry in the SG table, without this
patch the DMA would be cancelled in the middle, something we've no idea if it
happens on real hardware too or not. Overall this seems a great risk for zero
gain.
This approach is sure safer than previous code given we can't pretend all guest
fs code out there to check for errors and reply the DMA if it was completed
partially, given a timeout would never materialize on a real harddisk unless
there are defective blocks (and defective blocks are practically only an issue
for reads never for writes in any recent hardware as writing to blocks is the
way to fix them) or the harddisk breaks as a whole.
Signed-off-by: Izik Eidus <ieidus@redhat.com>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
* 'for-anthony' of git://repo.or.cz/qemu/kevin:
Fix -snapshot deleting images on disk change
block: Use error codes from lower levels for error message
block: default to 0 minimal / optiomal I/O size
move 'unsafe' to end of caching modes in help
virtio-blk: Create exit function to unregister savevm
block migration: propagate return value when bdrv_write() returns < 0
ide/atapi: add support for GET EVENT STATUS NOTIFICATION
Fix the following warnings:
/src/qemu/hw/ide/core.c: In function `ide_drive_pio_post_load':
/src/qemu/hw/ide/core.c:2767: warning: comparison is always false due to limited range of data type
/src/qemu/ui/vnc-enc-tight.c: In function `tight_detect_smooth_image':
/src/qemu/ui/vnc-enc-tight.c:284: warning: comparison is always true due to limited range of data type
/src/qemu/ui/vnc-enc-tight.c:297: warning: comparison is always true due to limited range of data type
/src/qemu/ui/vnc-enc-tight.c: In function `tight_encode_indexed_rect16':
/src/qemu/ui/vnc-enc-tight.c:456: warning: comparison is always false due to limited range of data type
/src/qemu/ui/vnc-enc-tight.c: In function `tight_encode_indexed_rect32':
/src/qemu/ui/vnc-enc-tight.c:457: warning: comparison is always false due to limited range of data type
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
It reintroduces
Revert "ide save/restore pio/atapi cmd transfer fields and io buffer"
but using subsections. Added bonus is the addition of ide_dummy_transfer_stop
to transfer_end_table, that was missing.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This reverts commit ed487bb1d6.
The conflicts are due to commit 4fc8d6711a
that is a fix to the ide_drive_pre_save() function. It reverts both
(and both are reinstantiated later in the series)
Conflicts:
hw/ide/core.c
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The GET EVENT STATUS NOTIFICATION is a mandatory command according
to MMC-3, even if event status notification is not supported.
This patch adds support for this command. It returns NEA ("No Event
Available") with an empty "Supported Event Classes" to show that it
doesn't event support status notification. If asychronous operation is
requested, which requires NCQ support, it returns an error according
to the specifications.
This fixes HAL support on FreeBSD and derivatives, which fill up the
logs every second with:
acd0: FAILURE - unknown CMD (0x03) ILLEGAL REQUEST asc=0x20 ascq=0x00
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Disks without media make no sense. For SCSI, a Linux guest kernel
complains during boot. I didn't try other combinations.
scsi-generic doesn't need the additional check, because it already
requires bdrv_is_sg(), which fails without media.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The file, vt82c686.c, was added after the change set of
b80d4a9887 and
fecb93c45c
are created, but before the patch series was commit.
So similar fix is needed to vt82c686.c.
Cc: Huacai Chen <zltjiangshi@gmail.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Don't overwrite pci header type.
Otherwise, multi function bit which pci_init_header_type() sets
appropriately is lost.
Anyway PCI_HEADER_TYPE_NORMAL is zero, so it is unnecessary to zero
which is already zero cleared.
how to test:
run qemu and issue info pci to see whether a device in question is
normal device, not pci-to-pci bridge.
This is handy because guest os isn't required.
tested changes:
The following files are covered by using following commands.
sparc64-softmmu
apb_pci.c, vga-pci.c, cmd646.c, ne2k_pci.c, sun4u.c
ppc-softmmu
grackle_pci.c, cmd646.c, ne2k_pci.c, vga-pci.c, macio.c
ppc-softmmu -M mac99
unin_pci.c(uni-north, uni-north-agp)
ppc64-softmmu
pci-ohci, ne2k_pci, vga-pci, unin_pci.c(u3-agp)
x86_64-softmmu
acpi_piix4.c, ide/piix.c, piix_pci.c
-vga vmware vmware_vga.c
-watchdog i6300esb wdt_i6300esb.c
-usb usb-uhci.c
-sound ac97 ac97.c
-nic model=rtl8139 rtl8139.c
-nic model=pcnet pcnet.c
-balloon virtio virtio-pci.c:
untested changes:
The following changes aren't tested.
prep_pci.c: ppc-softmmu -M prep should cover, but core dumped.
unin_pci.c(uni-north-pci): the caller is commented out.
openpic.c: the caller is commented out in ppc_prep.c
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
These will be used to generate unique id strings for ramblocks. The name
field is required, the device pointer is optional as most callers don't
have a device. When there's no device or the device isn't a child of
a bus implementing BusInfo.get_dev_path, the name should be unique for
the platform.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When available, we'd like to be able to access the DeviceState
when registering a savevm. For buses with a get_dev_path()
function, this will allow us to create more unique savevm
id strings.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
drive_init() doesn't permit invalid CHS for if=ide, but that's
worthless: we get it via if=none and -device.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
drive_init() doesn't permit option readonly for if=ide, but that's
worthless: we get it via if=none and -device.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It still always succeeds. The next commits will add failures.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The two aren't independent variables. Make that obvious.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Use error_report(), because it points to the error location.
Reword "tried to assign twice" messages to make it clear that we're
complaining about the unit property.
Report invalid unit property instead of failing silently.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Drives defined with -drive if=ide get get created along with the IDE
controller, inside machine->init(). That's before cmos_init().
Drives defined with -device get created during generic device init.
That's after cmos_init(). Because of that, CMOS has no information on
them (type, geometry, translation). Older versions of Windows such as
XP reportedly choke on that.
Split off the part of CMOS initialization that needs to know about
-device devices, and turn it into a reset handler, so it runs after
device creation.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
BlockDriverState member removable controls whether virtual media
change (monitor commands change, eject) is allowed. It is set when
the "type hint" is BDRV_TYPE_CDROM or BDRV_TYPE_FLOPPY.
The type hint is only set by drive_init(). It sets BDRV_TYPE_FLOPPY
for if=floppy. It sets BDRV_TYPE_CDROM for media=cdrom and if=ide,
scsi, xen, or none.
if=ide and if=scsi work, because the type hint makes it a CD-ROM.
if=xen likewise, I think.
For the same reason, if=none works when it's used by ide-drive or
scsi-disk. For other guest devices, there are problems:
* fdc: you can't change virtual media
$ qemu [...] -drive if=none,id=foo,... -global isa-fdc.driveA=foo
QEMU 0.12.50 monitor - type 'help' for more information
(qemu) eject foo
Device 'foo' is not removable
unless you add media=cdrom, but that makes it readonly.
* virtio: if you add media=cdrom, you can change virtual media. If
you eject, the guest gets I/O errors. If you change, the guest sees
the drive's contents suddenly change.
* scsi-generic: if you add media=cdrom, you can change virtual media.
I didn't test what that does to the guest or the physical device,
but it can't be pretty.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
For instance, -device scsi-disk,drive=foo -device scsi-disk,drive=foo
happily creates two SCSI disks connected to the same block device.
It's all downhill from there.
Device usb-storage deliberately attaches twice to the same blockdev,
which fails with the fix in place. Detach before the second attach
there.
Also catch attempt to delete while a guest device model is attached.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Make the property point to BlockDriverState, cutting out the DriveInfo
middleman. This prepares the ground for block devices that don't have
a DriveInfo.
Currently all user-defined ones have a DriveInfo, because the only way
to define one is -drive & friends (they go through drive_init()).
DriveInfo is closely tied to -drive, and like -drive, it mixes
information about host and guest part of the block device. I'm
working towards a new way to define block devices, with clean
host/guest separation, and I need to get DriveInfo out of the way for
that.
Fortunately, the device models are perfectly happy with
BlockDriverState, except for two places: ide_drive_initfn() and
scsi_disk_initfn() need to check the DriveInfo for a serial number set
with legacy -drive serial=... Use drive_get_by_blockdev() there.
Device model code should now use DriveInfo only when explicitly
dealing with drives defined the old way, i.e. without -device.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
All callers of ide_create_drive() ignore its value. Currently
harmless, because it fails only when qdev_init() fails, which fails
only when ide_drive_initfn() fails, which never fails.
Brittle. Change it to die instead of silently ignoring failure.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
That's where they belong semantically (block device host part), even
though the actions are actually executed by guest device code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Anything that moves hundreds of lines out of vl.c can't be all bad.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Show the actual default value instead of <null> when the property has
not been set.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It needs to be a qdev property, because it belongs to the drive's
guest part.
Bonus: info qtree now shows the serial number.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
IDEState members drive_serial_str and version are now left empty until
an actual drive is connected. Before, they got a default value that
was overwritten when a drive got connected. Doesn't matter, because
they're used only while a drive is connected.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit 428c149b added IDEState member conf to let commit 0009baf1 find
the BlockConf from there. It exists only for qdev drives, created via
ide_drive_initfn(), not for drives created via ide_init2().
But for a qdev drive, we can just as well reach its IDEDevice, which
contains the BlockConf. Do that, and revert the parts of commit
428c149b that add IDEState member conf.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When cancelling a request, bdrv_aio_cancel may decide that it waits for
completion of a request rather than for cancellation. IDE therefore can't
abandon its DMA status before calling bdrv_aio_cancel; otherwise the callback
of a completed request would use invalid data.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We cannot install different opaque pointer for read and write
of the same i/o address.
- handle zero address in bmdma_writeb_common and install
the same opaque pointer for both read and write access.
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Instead of doing tricks to get the pci_dev, just pass it in the 1st
place. Patch is a bit longer that reverting the pci_dev field, but it
states more clearly (IMHO) what we are doing.
It also fixes the bm test, now that you told me that ->unit is not
always valid.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Make win2k install hack unconditional as it is still restricted to
x86 only in vl.c.
Replace TARGET_PAGE_SIZE and 4096 with PAGE_SIZE.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The next commit will move the STOP event into do_vm_stop(), to
have the expected event sequence we need to emit the I/O error
event before calling vm_stop().
The expected sequence is:
{ "event": "BLOCK_IO_ERROR" [...] }
{ "event": "STOP" }
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
/src/qemu/hw/ide/core.c: In function 'ide_drive_pre_save':
/src/qemu/hw/ide/core.c:2740: warning: comparison is always false due to limited range of data type
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Save/restore information necessary to continue in progress PIO/ATAPI CMD
transfers.
This includes the IO buffer.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Export the physical block size in the ATA IDENTIFY command. The
other topology values are not supported in ATA so skip them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add three new qdev properties to export block topology information to
the guest. This is needed to get optimal I/O alignment for RAID arrays
or SSDs.
The options are:
- physical_block_size to specify the physical block size of the device,
this is going to increase from 512 bytes to 4096 kilobytes for many
modern storage devices
- min_io_size to specify the minimal I/O size without performance impact,
this is typically set to the RAID chunk size for arrays.
- opt_io_size to specify the optimal sustained I/O size, this is
typically the RAID stripe width for arrays.
I decided to not auto-probe these values from blkid which might easily
be possible as I don't know how to deal with these issues on migration.
Note that we specificly only set the physical_block_size, and not the
logial one which is the unit all I/O is described in. The reason for
that is that IDE does not support increasing the logical block size and
at last for now I want to stick to one meachnisms in queue and allow
for easy switching of transports for a given backing image which would
not be possible if scsi and virtio use real 4k sectors, while ide only
uses the physical block exponent.
To make this more common for the different block drivers introduce a
new BlockConf structure holding all common block properties and a
DEFINE_BLOCK_PROPERTIES macro to add them all together, mirroring
what is done for network drivers. Also switch over all block drivers
to use it, except for the floppy driver which has weird driveA/driveB
properties and probably won't require any advanced block options ever.
Example usage for a virtio device with 4k physical block size and
8k optimal I/O size:
-drive file=scratch.img,media=disk,cache=none,id=scratch \
-device virtio-blk-pci,drive=scratch,physical_block_size=4096,opt_io_size=8192
aliguori: updated patch to take into account BLOCK events
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Just call bdrv_mon_event() in the right place.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If migration takes place between write of the bmdma address register and
write of the command register (to initiate DMA), the destination will
not properly start the DMA op, hanging the guest:
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.00: cmd c8/00:16:41:00:00/00:00:00:00:00/e0 tag 0 dma 11264 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
Fix by sending current transfer information in the migration data.
We need to update ide version to 4 for this to work. As we don't
have subsectios, we need to chain the update increase until
vmstate_ide_pci (quintela)
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds a new property named 'ver' to ide-drive which allows to
specify the version which the virtual disk/cdrom should report to the
guest. By default this is the qemu version (i.e. 0.12). usage:
-drive if=none,id=disk,file=...
-device ide-drive,bus=ide.0,unit=0,drive=disk,ver=42
You can also switch the version for all ide drives using:
-global ide-drive.ver=42
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
This is a workaround only, and is a partial revert
of a few changes to BMDMAState which removed pci_dev
field on the way.
- cmd646 pci_from_bm() expects bm->unit value to
correspond with bm data being passed to callback
as opaque pointer. This breaks when write to dma
control register of second channel happens when no
dma operation is in progress, so bm->unit is zero
for second channel, and pci_from_bm() returns garbage
pointer. Crash happens shortly after that while
dereferencing that pointer.
v0->v1: cleaned up dead code from pci_from_bm.
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Device names with whitespace require quoting in the shell and in the
monitor. Some of the offenders are also overly long. Some have a
more convenient alias, some don't.
The place for verbose device names is DeviceInfo member desc. The
name should be short & sweet.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This implements the audio control or volume read support as needed by
some systems. A Conectiva Parolin system required this to detect an IDE
device as CD-ROM, through the CDVOLREAD ioctl.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Some PAGE constants were used instead of the macros we already have
defined in internal.h.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Either rename variables and functions to refer to write errors (which is what
they actually do) or introduce a parameter to distinguish reads and writes.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch is preliminary for 64 bit BAR support.
Introduce dedicated type, pcibus_t, to represent pci bus address/size
instead of uint32_t.
Later this type will be changed to uint64_t.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
make constants for pci base address match pci_regs.h by
renaming PCI_ADDRESS_SPACE_xxx to PCI_BASE_ADDRESS_SPACE_xxx.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
These devices are created automatically, and attempting to create
another one with -device fails with "qemu: hardware error:
register_ioport_write: invalid opaque".
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Problem: x86 systems could not survive a few system_resets.
Clear most of IDE state when reset. Implement the missing reset handlers.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
There is absolutely no need to call reset functions when initializing
devices. Since we are already registering them, calling qemu_system_reset()
should suffice. Actually, it is what happens when we reboot the machine,
and using the same process instead of a special case semantics will even
allow us to find bugs easier.
Furthermore, the fact that we initialize things like the cpu quite early,
leads to the need to introduce synchronization stuff like qemu_system_cond.
This patch removes it entirely. All we need to do is call qemu_system_reset()
only when we're already sure the system is up and running
I tested it with qemu (with and without io-thread) and qemu-kvm, and it
seems to be doing okay - although qemu-kvm uses a slightly different patch.
[ v2: user mode still needs cpu_reset, so put it in ifdef. ]
[ v3: leave qemu_system_cond for now. ]
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Change pointer to struct by embedded struct.
Adjust all callers
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
It is used everywhere as uint8_t except in one place. Cast to uint16_t
in that place
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
We have split the functions that needed it for cmd646
Patchworks-ID: 35302
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch splits cmd646 specific code from pci.c.
This patch splits piix4 specific code from pci.c.
And compile new piix.o and cmd646.o when they are needed.
The only change that is not code movemet is removal of cmd646 specific parts
in bmdma_readb/writeb for piix.
Patchworks-ID: 35301
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
We already have a PCIDevice at that point
Patchworks-ID: 35296
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Some callers test for != 0, some for < 0. Normalize to < 0.
Patchworks-ID: 35171
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Like qdev_init(), but terminate program via hw_error() instead of
returning an error value.
Use it instead of qdev_init() where terminating the program on failure
is okay, either because it's during machine construction, or because
we know that failure can't happen.
Because relying in the latter is somewhat unclean, and the former is
not always obvious, it would be nice to go back to qdev_init() in the
not-so-obvious cases, only with proper error handling. I'm leaving
that for another day, because it involves making sure that error
values are properly checked by all callers.
Patchworks-ID: 35168
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
It's qdev_create() specialized for PCI, so name it accordingly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
In the very least, a change like this requires discussion on the list.
The naming convention is goofy and it causes a massive merge problem. Something
like this _must_ be presented on the list first so people can provide input
and cope with it.
This reverts commit 99a0949b72.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
With this patch applied ide drives (when attached to a pci adapter) can
be created via -device, like this:
-drive if=none,id=mydisk,file=/path/to/disk.img
-device ide-drive,drive=mydisk,bus=ide.0,unit=0
Note that creating a master on ide1 doesn't work that way. That is a
side effect of qemu creating a cdrom automagically even if you don't
ask for it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This allows the ide bus being initialized without drives attached
and the drives being attached and initialization later on as
separate step.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Add a enable_write_cache flag in the block driver state, and use it to
decide if we claim to have a volatile write cache that needs controlled
flushing from the guest. The flag is off if cache=writethrough is
defined because O_DSYNC guarantees that every write goes to stable
storage, and it is on for cache=none and cache=writeback.
Both scsi-disk and ide now use the new flage, changing from their
defaults of always off (ide) or always on (scsi-disk).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
8baf73adf6 (qdev/isa: convert fdc)
breaks MIPS Malta:
Tried to create isa device isa-fdc with no isa bus present
Fix this by creating an isa bus for piix4.
This change also requires some more qdev related changes
(similar changes were applied to pc.c) and allows
cleaning of piix3/piix4 code.
Thanks to Gerd Hoffmann for his hints.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
These variables are per bus, not per drive. Lets move them and
cleanup things a bit. And fix the cmd migration bug for real.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
