MacOS (un)helpfully leaves the FIFO engine running even when all the samples have
been written to the hardware, and expects the FIFO status flags and IRQ to be
updated continuously.
There is an additional problem in that not all audio backends guarantee an
all-zero output when there is no FIFO data available, in particular the Windows
dsound backend which re-uses its internal circular buffer causing the last played
sound to loop indefinitely.
Whilst this is effectively a bug in the Windows dsound backend, work around it
for now using a simple heuristic: if the FIFO remains empty for half a cycle
(~23ms) then continuously fill the generated buffer with empty silence.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-ID: <20231004083806.757242-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The Apple Sound Chip was primarily used by the Macintosh II to generate sound
in hardware which was previously handled by the toolbox ROM with software
interrupts.
Implement both the standard ASC and also the enhanced ASC (EASC) functionality
which is used in the Quadra 800.
Note that whilst real ASC hardware uses AUDIO_FORMAT_S8, this implementation uses
AUDIO_FORMAT_U8 instead because AUDIO_FORMAT_S8 is rarely used and not supported
by some audio backends like PulseAudio and DirectSound when played directly with
-audiodev out.mixing-engine=off.
Co-developed-by: Laurent Vivier <laurent@vivier.eu>
Co-developed-by: Volker Rümelin <vr_qemu@t-online.de>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20231004083806.757242-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
MacOS attempts a series of writes and reads over the entire RAM area in order
to determine the amount of RAM within the machine. Allow accesses to the
entire RAM area ignoring writes and always reading zero for areas where there
is no physical RAM installed to allow MacOS to detect the memory size without
faulting.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-ID: <20231004083806.757242-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
It is needed because it defines the BIOSConfig area.
Co-developed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-ID: <20231004083806.757242-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
MacOS reads this address to identify the hardware.
This is a basic implementation returning the ID of Quadra 800.
Details:
http://mess.redump.net/mess/driver_info/mac_technical_notes
"There are 3 ID schemes [...]
The third and most scalable is a machine ID register at 0x5ffffffc.
The top word must be 0xa55a to be valid. Then bits 15-11 are 0 for
consumer Macs, 1 for portables, 2 for high-end 68k, and 3 for high-end
PowerPC. Bit 10 is 1 if additional ID bits appear elsewhere (e.g. in VIA1).
The rest of the bits are a per-model identifier.
Model Lower 16 bits of ID
...
Quadra/Centris 610/650/800 0x2BAD"
Co-developed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20231004083806.757242-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The djMEMC controller is used to store information related to the physical memory
configuration.
Co-developed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20231004083806.757242-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Convert the GLUE device to 3-phase reset. The legacy method
doesn't do anything that's invalid in the hold phase, so the
conversion is simple and not a behaviour change.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-ID: <20231004083806.757242-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
vdpa:
shadow vq vlan support
net migration with cvq
cxl:
support emulating 4 HDM decoders
serial number extended capability
virtio:
hared dma-buf
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmUd4/YPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpyM8H/02cRbJcQOjYt7j68zPW6GaDXxBI/UmdWDyG
15LZZbGNOPjyjNd3Vz1M7stQ5rhoKcgo/RdI+0E60a78svgW5JvpXoXR3pksc3Dx
v28B/akXwHUErYFSZQ+2VHNc8OhCd0v2ehxZxbwPEAYIOAj3hcCIVoPGXTnKJmAJ
imr5hjH0wZUc0+xdsmn8Vfdv5NTzpwfVObbGiMZejeJsaoh0y6Rt8RANBMY67KQD
S7/HPlVuDYf/y43t4ZEHNYuV9RaCdZZYlLWwV1scdKaYcofgmtJOKbOdCjHRXgj+
004Afb3rggIoCfnCzOFzhGx+MLDtLjvEn2N4oLEWCLi+k/3huaA=
=GAvH
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pci: features, cleanups
vdpa:
shadow vq vlan support
net migration with cvq
cxl:
support emulating 4 HDM decoders
serial number extended capability
virtio:
hared dma-buf
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (53 commits)
libvhost-user: handle shared_object msg
vhost-user: add shared_object msg
hw/display: introduce virtio-dmabuf
util/uuid: add a hash function
virtio: remove unused next argument from virtqueue_split_read_next_desc()
virtio: remove unnecessary thread fence while reading next descriptor
virtio: use shadow_avail_idx while checking number of heads
libvhost-user.c: add assertion to vu_message_read_default
pcie_sriov: unregister_vfs(): fix error path
hw/i386/pc: improve physical address space bound check for 32-bit x86 systems
amd_iommu: Fix APIC address check
vdpa net: follow VirtIO initialization properly at cvq isolation probing
vdpa net: stop probing if cannot set features
vdpa net: fix error message setting virtio status
hw/pci-bridge/cxl-upstream: Add serial number extended capability support
hw/cxl: Support 4 HDM decoders at all levels of topology
hw/cxl: Fix and use same calculation for HDM decoder block size everywhere
hw/cxl: Add utility functions decoder interleave ways and target count.
hw/cxl: Push cxl_decoder_count_enc() and cxl_decode_ig() into .c
vdpa net: zero vhost_vdpa iova_tree pointer at cleanup
...
Conflicts:
hw/core/machine.c
Context conflict with commit 314e0a84cd ("hw/core: remove needless
includes") because it removed an adjacent #include.
In the libvhost-user library we need to
handle VHOST_USER_GET_SHARED_OBJECT requests,
and add helper functions to allow sending messages
to interact with the virtio shared objects
hash table.
Signed-off-by: Albert Esteve <aesteve@redhat.com>
Message-Id: <20231002065706.94707-5-aesteve@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add three new vhost-user protocol
`VHOST_USER_BACKEND_SHARED_OBJECT_* messages`.
These new messages are sent from vhost-user
back-ends to interact with the virtio-dmabuf
table in order to add or remove themselves as
virtio exporters, or lookup for virtio dma-buf
shared objects.
The action taken in the front-end depends
on the type stored in the virtio shared
object hash table.
When the table holds a pointer to a vhost
backend for a given UUID, the front-end sends
a VHOST_USER_GET_SHARED_OBJECT to the
backend holding the shared object.
The messages can only be sent after successfully
negotiating a new VHOST_USER_PROTOCOL_F_SHARED_OBJECT
vhost-user protocol feature bit.
Finally, refactor code to send response message so
that all common parts both for the common REPLY_ACK
case, and other data responses, can call it and
avoid code repetition.
Signed-off-by: Albert Esteve <aesteve@redhat.com>
Message-Id: <20231002065706.94707-4-aesteve@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This API manages objects (in this iteration,
dmabuf fds) that can be shared along different
virtio devices, associated to a UUID.
The API allows the different devices to add,
remove and/or retrieve the objects by simply
invoking the public functions that reside in the
virtio-dmabuf file.
For vhost backends, the API stores the pointer
to the backend holding the object.
Suggested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Albert Esteve <aesteve@redhat.com>
Message-Id: <20231002065706.94707-3-aesteve@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add hash function to uuid module using the
djb2 hash algorithm.
Add a couple simple unit tests for the hash
function, checking collisions for similar UUIDs.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Albert Esteve <aesteve@redhat.com>
Message-Id: <20231002065706.94707-2-aesteve@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The 'next' was converted from a local variable to an output parameter
in commit:
412e0e81b1 ("virtio: handle virtqueue_read_next_desc() errors")
But all the actual uses of the 'i/next' as an output were removed a few
months prior in commit:
aa570d6fb6 ("virtio: combine the read of a descriptor")
Remove the unused argument to simplify the code.
Also, adding a comment to the function to describe what it is actually
doing, as it is not obvious that the 'desc' is both an input and an
output argument.
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Message-Id: <20230927140016.2317404-3-i.maximets@ovn.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It was supposed to be a compiler barrier and it was a compiler barrier
initially called 'wmb' when virtio core support was introduced.
Later all the instances of 'wmb' were switched to smp_wmb to fix memory
ordering issues on non-x86 platforms. However, this one doesn't need
to be an actual barrier, as its only purpose was to ensure that the
value is not read twice.
And since commit aa570d6fb6 ("virtio: combine the read of a descriptor")
there is no need for a barrier at all, since we're no longer reading
guest memory here, but accessing a local structure.
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Message-Id: <20230927140016.2317404-2-i.maximets@ovn.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We do not need the most up to date number of heads, we only want to
know if there is at least one.
Use shadow variable as long as it is not equal to the last available
index checked. This avoids expensive qatomic dereference of the
RCU-protected memory region cache as well as the memory access itself.
The change improves performance of the af-xdp network backend by 2-3%.
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Message-Id: <20230927135157.2316982-1-i.maximets@ovn.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Explain Coverity that we are not going to overflow vmsg->fds.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Message-Id: <20230925194040.68592-5-vsementsov@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
local_err must be NULL before calling object_property_set_bool(), so we
must clear it on each iteration. Let's also use more convenient
error_reportf_err().
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Message-Id: <20230925194040.68592-8-vsementsov@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
32-bit x86 systems do not have a reserved memory for hole64. On those 32-bit
systems without PSE36 or PAE CPU features, hotplugging memory devices are not
supported by QEMU as QEMU always places hotplugged memory above 4 GiB boundary
which is beyond the physical address space of the processor. Linux guests also
does not support memory hotplug on those systems. Please see Linux
kernel commit b59d02ed08690 ("mm/memory_hotplug: disable the functionality
for 32b") for more details.
Therefore, the maximum limit of the guest physical address in the absence of
additional memory devices effectively coincides with the end of
"above 4G memory space" region for 32-bit x86 without PAE/PSE36. When users
configure additional memory devices, after properly accounting for the
additional device memory region to find the maximum value of the guest
physical address, the address will be outside the range of the processor's
physical address space.
This change adds improvements to take above into consideration.
For example, previously this was allowed:
$ ./qemu-system-x86_64 -cpu pentium -m size=10G
With this change now it is no longer allowed:
$ ./qemu-system-x86_64 -cpu pentium -m size=10G
qemu-system-x86_64: Address space limit 0xffffffff < 0x2bfffffff phys-bits too low (32)
However, the following are allowed since on both cases physical address
space of the processor is 36 bits:
$ ./qemu-system-x86_64 -cpu pentium2 -m size=10G
$ ./qemu-system-x86_64 -cpu pentium,pse36=on -m size=10G
For 32-bit, without PAE/PSE36, hotplugging additional memory is no longer allowed.
$ ./qemu-system-i386 -m size=1G,maxmem=3G,slots=2
qemu-system-i386: Address space limit 0xffffffff < 0x1ffffffff phys-bits too low (32)
$ ./qemu-system-i386 -machine q35 -m size=1G,maxmem=3G,slots=2
qemu-system-i386: Address space limit 0xffffffff < 0x1ffffffff phys-bits too low (32)
A new compatibility flag is introduced to make sure pc_max_used_gpa() keeps
returning the old value for machines 8.1 and older.
Therefore, the above is still allowed for older machine types in order to support
compatibility. Hence, the following still works:
$ ./qemu-system-i386 -machine pc-i440fx-8.1 -m size=1G,maxmem=3G,slots=2
$ ./qemu-system-i386 -machine pc-q35-8.1 -m size=1G,maxmem=3G,slots=2
Further, following is also allowed as with PSE36, the processor has 36-bit
address space:
$ ./qemu-system-i386 -cpu 486,pse36=on -m size=1G,maxmem=3G,slots=2
After calling CPUID with EAX=0x80000001, all AMD64 compliant processors
have the longmode-capable-bit turned on in the extended feature flags (bit 29)
in EDX. The absence of CPUID longmode can be used to differentiate between
32-bit and 64-bit processors and is the recommended approach. QEMU takes this
approach elsewhere (for example, please see x86_cpu_realizefn()), With
this change, pc_max_used_gpa() also uses the same method to detect 32-bit
processors.
Unit tests are modified to not run 32-bit x86 tests that use memory hotplug.
Suggested-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Ani Sinha <anisinha@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230922160413.165702-1-anisinha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
An MSI from I/O APIC may not exactly equal to APIC_DEFAULT_ADDRESS. In
fact, Windows 17763.3650 configures I/O APIC to set the dest_mode bit.
Cover the range assigned to APIC.
Fixes: 577c470f43 ("x86_iommu/amd: Prepare for interrupt remap support")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20230921114612.40671-1-akihiko.odaki@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch solves a few issues. The most obvious is that the feature
set was done previous to ACKNOWLEDGE | DRIVER status bit set. Current
vdpa devices are permissive with this, but it is better to follow the
standard.
Fixes: 152128d646 ("vdpa: move CVQ isolation check to net_init_vhost_vdpa")
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20230915170836.3078172-4-eperezma@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Otherwise it continues the CVQ isolation probing.
Fixes: 152128d646 ("vdpa: move CVQ isolation check to net_init_vhost_vdpa")
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20230915170836.3078172-3-eperezma@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
It incorrectly prints "error setting features", probably because a copy
paste miss.
Fixes: 152128d646 ("vdpa: move CVQ isolation check to net_init_vhost_vdpa")
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20230915170836.3078172-2-eperezma@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Will be needed so there is a defined serial number for
information queries via the Switch CCI.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230913133615.29876-1-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Support these decoders in CXL host bridges (pxb-cxl), CXL Switch USP
and CXL Type 3 end points.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230913132523.29780-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In order to avoid having the size of the per HDM decoder register block
repeated in lots of places, create the register definitions for HDM
decoder 1 and use the offset between the first registers in HDM decoder 0 and
HDM decoder 1 to establish the offset.
Calculate in each function as this is more obvious and leads to shorter
line lengths than a single #define which would need a long name
to be specific enough.
Note that the code currently only supports one decoder, so the bugs this
fixes don't actually affect anything.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230913132523.29780-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As an encoded version of these key configuration parameters is available
in a register, provide functions to extract it again so as to avoid
the need for duplicating the storage.
Whilst here update the _enc() function to include additional values
as defined in the CXL 3.0 specification. Whilst they are not
currently used in the emulation, they may be in future and it is
easier to compare with the specification if all values are covered.
Add a spec reference for cxl_interleave_ways_enc() for consistency
with the target count equivalent (and because it's nice to know where
the magic numbers come from).
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230913132523.29780-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is no strong justification for keeping these in the header
so push them down into the associated cxl-component-utils.c file.
Suggested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230913132523.29780-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Not zeroing it causes a SIGSEGV if the live migration is cancelled, at
net device restart.
This is caused because CVQ tries to reuse the iova_tree that is present
in the first vhost_vdpa device at the end of vhost_vdpa_net_cvq_start.
As a consequence, it tries to access an iova_tree that has been already
free.
Fixes: 00ef422e9f ("vdpa net: move iova tree creation from init to start")
Reported-by: Yanhui Ma <yama@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20230913123408.2819185-1-eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
gcc 13.2.1 emits the following warning:
net/vhost-vdpa.c: In function ‘net_vhost_vdpa_init.constprop’:
net/vhost-vdpa.c:1394:25: error: ‘cvq_isolated’ may be used uninitialized [-Werror=maybe-uninitialized]
1394 | s->cvq_isolated = cvq_isolated;
| ~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~
net/vhost-vdpa.c:1355:9: note: ‘cvq_isolated’ was declared here
1355 | int cvq_isolated;
| ^~~~~~~~~~~~
cc1: all warnings being treated as errors
Cc: Eugenio Pérez <eperezma@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20230911215435.4156314-1-stefanha@redhat.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The bit positions of both registers are related. Tracing the registers
independently results in the same offsets across these registers which
eases debugging.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230908084234.17642-9-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230908084234.17642-8-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The SMI command port is currently hardcoded by means of the ACPI_PORT_SMI_CMD
macro. This hardcoding is Intel specific and doesn't match VIA, for example.
There is already the AcpiFadtData::smi_cmd attribute which is used when building
the FADT. Let's also use it when building the DSDT which confines SMI command
port determination to just one place. This allows it to become a property later,
thus resolving the Intel assumption.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230908084234.17642-7-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now that TYPE_ACPI_GED_X86 doesn't assign AcpiDeviceIfClass::madt_cpu any more
it is the same as TYPE_ACPI_GED.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230908084234.17642-6-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The "hw/boards.h" is unused since the previous commit. Since its removal
requires include fixes in various unrelated files to keep the code compiling it
has been split in a dedicated commit.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230908084234.17642-5-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This virtual method was always set to the x86-specific pc_madt_cpu_entry(),
even in piix4 which is also used in MIPS. The previous changes use
pc_madt_cpu_entry() otherwise, so madt_cpu can be dropped.
Since pc_madt_cpu_entry() is now only used in x86-specific code, the stub
in hw/acpi/acpi-x86-stub can be removed as well.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230908084234.17642-4-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
build_cpus_aml() is architecture independent but needs to create architecture-
specific CPU AML. So far this was achieved by using a virtual method from
TYPE_ACPI_DEVICE_IF. However, build_cpus_aml() would resolve this interface from
global (!) state. This makes it quite incomprehensible where this interface
comes from (TYPE_PIIX4_PM?, TYPE_ICH9_LPC_DEVICE?, TYPE_ACPI_GED_X86?) an can
lead to crashes when the generic code is ported to new architectures.
So far, build_cpus_aml() is only called in architecture-specific code -- and
only in x86. We can therefore simply pass pc_madt_cpu_entry() as callback to
build_cpus_aml(). This is the same callback that would be used through
TYPE_ACPI_DEVICE_IF.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230908084234.17642-3-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This is x86-specific code, so there is no advantage in using
pc_madt_cpu_entry() behind an architecture-agnostic interface.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230908084234.17642-2-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fix:
In file included from ../tcg/tcg.c:735:
/home1/gaosong/bugfix/qemu/tcg/loongarch64/tcg-target.c.inc: In function ‘tcg_out_vec_op’:
/home1/gaosong/bugfix/qemu/tcg/loongarch64/tcg-target.c.inc:1855:9: error: a label can only be part of a statement and a declaration is not a statement
TCGCond cond = args[3];
^~~~~~~
Signed-off-by: gaosong <gaosong@loongson.cn>
Message-Id: <20230926075819.3602537-1-gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Commit 18a536f1f8 ("accel/tcg: Always require can_do_io") fixed
the GitLab issue #1884: we can now re-enable those tests.
This reverts commit f959c3d87c.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20231003063808.66564-1-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This build option has been deprecated since 8.0.
Remove all CONFIG_GPROF code that depends on that,
including one errant check using TARGET_GPROF.
Acked-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Use abi_ullong not uint64_t so that the alignment of the field
and therefore the layout of the struct is correct.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The tcg/tcg.h header is a big bucket, containing stuff related to
the translators and the JIT backend. The places that initialize
tcg or create new threads do not need all of that, so split out
these three functions to a new header.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We can load tcg_ctx just as easily within the callee.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
cpu_in_serial_context() is not target specific,
move it declaration to "internal-common.h" (which
we include in the 4 source files modified).
Remove the unused "exec/exec-all.h" header from
cpu-exec-common.c. There is no more target specific
code in this file: make it target agnostic.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Anton Johansson <anjo@rev.ng>
Message-Id: <20230914185718.76241-12-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Remove the unused "exec/exec-all.h" header. There is
no more target specific code in it: make it target
agnostic (rename using the '-common' suffix). Since
it is TCG specific, move it to accel/tcg, updating
MAINTAINERS.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Anton Johansson <anjo@rev.ng>
Message-Id: <20230914185718.76241-11-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Move target-agnostic declarations from "internal-target.h"
to a new "internal-common.h" header.
monitor.c now don't include target specific headers and can
be compiled once in system_ss[].
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Anton Johansson <anjo@rev.ng>
Message-Id: <20230914185718.76241-10-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
accel/tcg/internal.h contains target specific declarations.
Unit files including it become "target tainted": they can not
be compiled as target agnostic. Rename using the '-target'
suffix to make this explicit.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Anton Johansson <anjo@rev.ng>
Message-Id: <20230914185718.76241-9-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This matches the target agnostic 'page-vary-common.c' counterpart.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Anton Johansson <anjo@rev.ng>
Message-Id: <20230914185718.76241-8-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
