The guest OS reads RSTAT, RSEQ, and RINTR, and expects those registers
to reflect a consistent state. However, it is possible that the registers
can change after RSTAT was read, but before RINTR is read, when
esp_command_complete() is called.
Guest OS qemu
-------- ----
[handle interrupt]
Read RSTAT
esp_command_complete()
RSTAT = STAT_ST
esp_dma_done()
RSTAT |= STAT_TC
RSEQ = 0
RINTR = INTR_BS
Read RSEQ
Read RINTR RINTR = 0
RSTAT &= ~STAT_TC
RSEQ = SEQ_CD
The guest OS would then try to handle INTR_BS combined with an old
value of RSTAT. This sometimes resulted in lost events, spurious
interrupts, guest OS confusion, and stalled SCSI operations.
A typical guest error log (observed with various versions of Linux)
looks as follows.
scsi host1: Spurious irq, sreg=13.
...
scsi host1: Aborting command [84531f10:2a]
scsi host1: Current command [f882eea8:35]
scsi host1: Queued command [84531f10:2a]
scsi host1: Active command [f882eea8:35]
scsi host1: Dumping command log
scsi host1: ent[15] CMD val[44] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[00] event[0c]
scsi host1: ent[16] CMD val[01] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[02] event[0c]
scsi host1: ent[17] CMD val[43] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[02] event[0c]
scsi host1: ent[18] EVENT val[0d] sreg[92] seqreg[04] sreg2[00] ireg[18] ss[00] event[0c]
...
Defer handling command completion until previous interrupts have been
handled to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Per AM53C974 datasheet, definition of "SCSI Bus and Control (SBAC)"
register:
Bit 24 'STATUS' Write Erase Control
This bit controls the Write Erase feature on bits 3:1 and bit 6 of the DMA
Status Register ((B)+54h). When this bit is programmed to '1', the state
of bits 3:1 are preserved when read. Bits 3:1 are only cleared when a '1'
is written to the corresponding bit location. For example, to clear bit 1,
the value of '0000_0010b' should be written to the register. When the DMA
Status Preserve bit is '0', bits 3:1 are cleared when read.
The status register is currently defined to bit 12, not bit 24.
Also, its implementation is reversed: The status is auto-cleared if
the bit is set to 1, and must be cleared explicitly when the bit is
set to 0. This results in spurious interrupts reported by the Linux
kernel, and in some cases even results in stalled SCSI operations.
Set SBAC_STATUS to bit 24 and reverse the logic to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-Id: <1543442171-24863-1-git-send-email-linux@roeck-us.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Because they are supposed to remain const.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20181114132931.22624-1-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Under heavy IO (e.g. fio) the queue is not checked frequently enough for
pending commands. As a result some pending commands are timed out by the
linux sym53c8xx driver, which sends SCSI Abort messages for the timed out
commands. The SCSI Abort messages result in linux errors, which show up
on the console and in /var/log/messages.
e.g.
sd 0:0:3:0: [sdd] tag#33 ABORT operation started
scsi target0:0:3: control msgout:
80 20 47 d
sd 0:0:3:0: ABORT operation complete.
scsi target0:0:4: message d sent on bad reselection
Now following a WAIT DISCONNECT Script instruction, and if there is no
current command, check for a pending command on the queue and if one
exists call lsi_reselect().
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Message-Id: <1541776692-12271-1-git-send-email-george.kennedy@oracle.com>
[For safety, add a s->current check in lsi_update_irq - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 40dce4ee6 "scsi-disk: fix rerror/werror=ignore" introduced a
bug which causes qemu to crash with the assertion error below if the
host file or disk returns an error:
qemu-system-x86_64: hw/scsi/scsi-bus.c:1374: scsi_req_complete:
Assertion `req->status == -1' failed.
Kevin Wolf suggested this fix:
< kwolf> Hm, should the final return false; in that patch
actually be a return true?
< kwolf> Because I think he didn't intend to change anything
except BLOCK_ERROR_ACTION_IGNORE
Buglink: https://bugs.launchpad.net/qemu/+bug/1804323
Fixes: 40dce4ee61
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Pass other sense, such as UNIT_ATTENTION or BUSY, directly to the
guest.
Reported-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Emulation of the block limits VPD page called back into scsi-disk.c,
which however expected the request to be for a SCSIDiskState and
accessed a scsi-generic device outside the bounds of its struct
(namely to retrieve s->max_unmap_size and s->max_io_size).
To avoid this, move the emulation code to a separate function that
takes a new SCSIBlockLimits struct and marshals it into the VPD
response format.
Reported-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A device can report an excessive number of VPD pages when asked for a
list; this can cause an out-of-bounds access to buf in
scsi_generic_set_vpd_bl_emulation. It should not happen, but
it is technically not incorrect so handle it: do not check any byte
past the allocation length that was sent to the INQUIRY command.
Reported-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Block limits emulation is just placing 0xb0 as the final byte of the
VPD pages list. However, VPD page numbers must be sorted, so change
that to an in-place insert. Since I couldn't find any disk that triggered
the loop more than once, this was tested by adding manually 0xb1
at the end of the list and checking that 0xb0 was added before.
Reported-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
While writing a message in 'lsi_do_msgin', message length value
in 'msg_len' could be invalid due to an invalid migration stream.
Add an assertion to avoid an out of bounds access, and reject
the incoming migration data if it contains an invalid message
length.
Discovered by Deja vu Security. Reported by Oracle.
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <20181026194314.18663-1-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are 3 virtqueues (ctrl, event and cmd) for virtio scsi device,
but seabios will only set the physical address for the 3rd one (cmd).
Then in vhost_virtqueue_start(), virtio_queue_get_desc_addr()
will be 0 for ctrl and event vq.
In this case, ctrl and event vq are not initialized.
vhost_verify_ring_mappings may use uninitialized vhost_virtqueue
such that vhost_verify_ring_part_mapping returns ENOMEM.
When encountered this problem, we got the following logs:
qemu-system-x86_64: Unable to map available ring for ring 0
qemu-system-x86_64: Verify ring failure on region 0
Signed-off-by: Forrest Liu <forrestl@synology.com>
Signed-off-by: yuchenlin <yuchenlin@synology.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
rerror=ignore was returning true from scsi_handle_rw_error but the callers were not
calling scsi_req_complete when rerror=ignore returns true (this is the correct thing
to do when true is returned after executing a passthrough command). Fix this by
calling it in scsi_handle_rw_error.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If a command fails with a sense that scsi_sense_buf_to_errno converts to
ECANCELED/EAGAIN/ENOTCONN or with a unit attention, scsi_req_complete is
called twice. This caused a crash.
Reported-by: Wangguang <wang.guangA@h3c.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When [2] was fixed it was agreed that adding and calling post_plug()
callback after device_reset() was low risk approach to hotfix issue
right before release. So it was merged instead of moving already
existing plug() callback after device_reset() is called which would
be more risky and require all plug() callbacks audit.
Looking at the current plug() callbacks, it doesn't seem that moving
plug() callback after device_reset() is breaking anything, so here
goes agreed upon [3] proper fix which essentially reverts [1][2]
and moves plug() callback after device_reset().
This way devices always comes to plug() stage, after it's been fully
initialized (including being reset), which fixes race condition [2]
without need for an extra post_plug() callback.
1. (25e897881 "qdev: add HotplugHandler->post_plug() callback")
2. (8449bcf94 "virtio-scsi: fix hotplug ->reset() vs event race")
3. https://www.mail-archive.com/qemu-devel@nongnu.org/msg549915.html
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1539696820-273275-1-git-send-email-imammedo@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Pierre Morel<pmorel@linux.ibm.com>
Acked-by: Pierre Morel<pmorel@linux.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Taking the address of a field in a packed struct is a bad idea, because
it might not be actually aligned enough for that pointer type (and
thus cause a crash on dereference on some host architectures). Newer
versions of clang warn about this. Avoid the bug by not using the
"modify in place" byte swapping functions.
This patch was produced with the following simple spatch script:
@@
expression E;
@@
-le16_to_cpus(&E);
+E = le16_to_cpu(E);
@@
expression E;
@@
-le32_to_cpus(&E);
+E = le32_to_cpu(E);
@@
expression E;
@@
-le64_to_cpus(&E);
+E = le64_to_cpu(E);
@@
expression E;
@@
-cpu_to_le16s(&E);
+E = cpu_to_le16(E);
@@
expression E;
@@
-cpu_to_le32s(&E);
+E = cpu_to_le32(E);
@@
expression E;
@@
-cpu_to_le64s(&E);
+E = cpu_to_le64(E);
followed by some minor tidying of overlong lines and bad indent.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20180927134852.21490-1-peter.maydell@linaro.org>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20180917053229.4853-1-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This option is added together with scsi-disk but is never honoured,
becuase we don't emulate the VPD page for scsi-block. We could intercept
and inject the user specified value like for max xfer len, but it's
probably not helpful since the intent of 070f80095a was for random
entropy aspects, not for performance. If emulated rotation rate is
desired, scsi-hd is more suitable.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20180917083138.3948-1-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On some early machines the on-board PCI devices IRQs are wired directly to
the interrupt controller instead of via the PCI host bridge.
Add an optional external IRQ that if wired up via qdev will replace the
in-built PCI IRQ.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that these functions are no longer required they can be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is the function that will soon be used to replace lsi53c895a_create() and
lsi53c810_create().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Allow toggling on/off the VIRTIO_SCSI_F_T10_PI feature bit for both
vhost-scsi and vhost-user-scsi devices.
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Message-Id: <20180808195235.5843-4-gedwards@ddn.com>
Reviewed-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the enablement of preset host features into the common
vhost_scsi_common_get_features() function. This is in preparation for
having vhost-scsi also make use of host_features.
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Message-Id: <20180808195235.5843-3-gedwards@ddn.com>
Reviewed-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In preparation for having vhost-scsi also make use of host_features,
move it from struct VHostUserSCSI into struct VHostSCSICommon.
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Message-Id: <20180808195235.5843-2-gedwards@ddn.com>
Reviewed-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The LSI 53c895a code does not handle the PPR Extended Message. Add
support to handle PPR Extended Message like SDTR and WDTR are handled.
That is, to skip past the message bytes and ignore the message.
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
mptsas1068 is currently listed as uncategorized device.
Mark it as storage device.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-Id: <1533076133-22745-1-git-send-email-linux@roeck-us.net>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This reinstates commit b008326744,
which was temporarily reverted for the 3.0 release so that libvirt gets
some extra time to update their command lines.
The -drive option serial was deprecated in QEMU 2.10. It's time to
remove it.
Tests need to be updated to set the serial number with -global instead
of using the -drive option.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
There is a race condition during hotplug when iothread is used. It
occurs because virtio-scsi may be processing command queues in the
iothread while the monitor performs SCSI device hotplug.
When a SCSI device is hotplugged the HotplugHandler->plug() callback is
invoked and virtio-scsi emits a rescan event to the guest.
If the guest submits a SCSI command at this point then it may be
cancelled before hotplug completes. This happens because ->reset() is
called by hw/core/qdev.c:device_set_realized() after
HotplugHandler->plug() has been called and
hw/scsi/scsi-disk.c:scsi_disk_reset() purges all requests.
This patch uses the new HotplugHandler->post_plug() callback to emit the
rescan event after ->reset(). This eliminates the race conditions where
requests could be cancelled.
Reported-by: l00284672 <lizhengui@huawei.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20180716083732.3347-3-stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The current BDC VPD page (page 0xb1) is too short. This can be
seen running sg_utils:
$ sg_vpd --page=bdc /dev/sda
Block device characteristics VPD page (SBC):
Block device characteristics VPD page length too short=8
By the SCSI spec, the expected size of the SBC page is 0x40.
There is no telling how the guest will behave with a shorter
message - it can ignore it, or worse, make (wrong)
assumptions.
This patch fixes the emulation by setting the size to 0x40.
This is the output of the previous sg_vpd command after
applying it:
$ sg_vpd --page=bdc /dev/sda -v
inquiry cdb: 12 01 b1 00 fc 00
Block device characteristics VPD page (SBC):
[PQual=0 Peripheral device type: disk]
Medium rotation rate is not reported
Product type: Not specified
WABEREQ=0
WACEREQ=0
Nominal form factor not reported
FUAB=0
VBULS=0
To improve readability, this patch also adds the VBULS value
explictly and add comments on the existing fields we're
setting.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This reverts commit b008326744.
Hold off removing this for one more QEMU release (current libvirt
release still uses it.)
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It eases code review, unit is explicit.
Patch generated using:
$ git grep -E '(1024|2048|4096|8192|(<<|>>).?(10|20|30))' hw/ include/hw/
and modified manually.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180625124238.25339-10-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The error handling policy was traditionally set with -drive, but with
-blockdev it is no longer possible to set frontend options. scsi-disk
(and other block devices) have long supported qdev properties to
configure the error handling policy, so let's add these options to
usb-storage as well and just forward them to the internal scsi-disk
instance.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
The VPD Block Limits Inquiry page is optional, allowing SCSI devices
to not implement it. This is the case for devices like the MegaRAID
SAS 9361-8i and Microsemi PM8069.
In case of SCSI passthrough, the response of this request is used by
the QEMU SCSI layer to set the max_io_sectors that the guest
device will support, based on the value of the max_sectors_kb that
the device has set in the host at that time. Without this response,
the guest kernel is free to assume any value of max_io_sectors
for the SCSI device. If this value is greater than the value from
the host, SCSI Sense errors will occur because the guest will send
read/write requests that are larger than the underlying host device
is configured to support. An example of this behavior can be seen
in [1].
A workaround is to set the max_sectors_kb host value back in the guest
kernel (a process that can be automated using rc.local startup scripts
and the like), but this has several drawbacks:
- it can be troublesome if the guest has many passthrough devices that
needs this tuning;
- if a change in max_sectors_kb is made in the host side, manual change
in the guests will also be required;
- during an OS install it is difficult, and sometimes not possible, to
go to a terminal and change the max_sectors_kb prior to the installation.
This means that the disk can't be used during the install process. The
easiest alternative here is to roll back to scsi-hd, install the guest
and then go back to SCSI passthrough when the installation is done and
max_sectors_kb can be set.
An easier way would be to QEMU handle the absence of the Block Limits
VPD device response, setting max_io_sectors accordingly and allowing
the guest to use the device without the hassle.
This patch adds emulation of the Block Limits VPD response for
SCSI passthrough devices of type TYPE_DISK that doesn't support
it. The following changes were made:
- scsi_handle_inquiry_reply will now check the available VPD
pages from the Inquiry EVPD reply. In case the device does not
- a new function called scsi_generic_set_vpd_bl_emulation,
that is called during device realize, was created to set a
new flag 'needs_vpd_bl_emulation' of the device. This function
retrieves the Inquiry EVPD response of the device to check for
VPD BL support.
- scsi_handle_inquiry_reply will now check the available VPD
pages from the Inquiry EVPD reply in case the device needs
VPD BL emulation, adding the Block Limits page (0xb0) to
the list. This will make the guest kernel aware of the
support that we're now providing by emulation.
- a new function scsi_emulate_block_limits creates the
emulated Block Limits response. This function is called
inside scsi_read_complete in case the device requires
Block Limits VPD emulation and we detected a SCSI Sense
error in the VPD Block Limits reply that was issued
from the guest kernel to the device. This error is
expected: we're reporting support from our side, but
the device isn't aware of it.
With this patch, the guest now queries the Block Limits
page during the device configuration because it is being
advertised in the Supported Pages response. It will either
receive the Block Limits page from the hardware, if it supports
it, or will receive an emulated response from QEMU. At any rate,
the guest now has the information to set the max_sectors_kb
parameter accordingly, sparing the user of SCSI sense errors
that would happen without the emulated response and in the
absence of Block Limits support from the hardware.
[1] https://bugzilla.redhat.com/show_bug.cgi?id=1566195
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1566195
Reported-by: Dac Nguyen <dacng@us.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20180627172432.11120-4-danielhb413@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For the VPD Block Limits emulation with SCSI passthrough,
we'll issue an Inquiry request with EVPD set to retrieve
the available VPD pages of the device. This would be done in
a way similar of what scsi_generic_read_device_identification
does: create a SCSI command and a reply buffer, fill in the
sg_io_hdr_t structure, call blk_ioctl, check if an error
occurred, process the response.
This same process is done in other 2 functions, get_device_type
and get_stream_blocksize. They differ in the command/reply
buffer and post-processing, everything else is almost a
copy/paste.
Instead of adding a forth copy/pasted-ish code when adding
the passthrough VPD BL emulation, this patch extirpates
this repetition of those 3 functions and put it into
a new one called scsi_SG_IO_FROM_DEV. Any future code that
wants to execute an SG_DXFER_FROM_DEV to the device can
use it, avoiding filling sg_io_hdr_t again and et cetera.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20180627172432.11120-3-danielhb413@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To add support for the emulation of Block Limits VPD page
for passthrough devices, a few adjustments in the current code
base is required to avoid repetition and improve clarity.
In scsi-generic.c, detach the Inquiry handling from
scsi_read_complete and put it into a new function called
scsi_handle_inquiry_reply. This change aims to avoid
cluttering of scsi_read_complete when we more logic in the
Inquiry response handling is added in the next patches,
centralizing the changes in the new function.
In scsi-disk.c, take the build of all emulated VPD pages
from scsi_disk_emulate_inquiry and make it available to
other files into a non-static function called
scsi_disk_emulate_vpd_page. Making it public will allow
the future VPD BL emulation code for passthrough devices
to use it from scsi-generic.c, avoiding copy/pasting this
code solely for that purpose. It also has the advantage of
providing emulation of all VPD pages in case we need to
emulate other pages in other scenarios. As a bonus,
scsi_disk_emulate_inquiry got tidier.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20180627172432.11120-2-danielhb413@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove the legacy esp_init() function now that there are no more remaining
users.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20180613094727.11326-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
The preferred way to select the KVM accelerator is to use "-accel kvm"
these days, so let's be consistent in our documentation and help texts.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1528866321-23886-3-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The -drive option serial was deprecated in QEMU 2.10. It's time to
remove it.
Tests need to be updated to set the serial number with -global instead
of using the -drive option.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbEXNvAAoJECgfDbjSjVRpc8gH/R8xrcFrV+k9wwbgYcOcGb6Y
LWjseE31pqJcxRV80vLOdzYEuLStZQKQQY7xBDMlA5vdyvZxIA6FLO2IsiJSbFAk
EK8pclwhpwQAahr8BfzenabohBv2UO7zu5+dqSvuJCiMWF3jGtPAIMxInfjXaOZY
odc1zY2D2EgsC7wZZ1hfraRbISBOiRaez9BoGDKPOyBY9G1ASEgxJgleFgoBLfsK
a1XU+fDM6hAVdxftfkTm0nibyf7PWPDyzqghLqjR9WXLvZP3Cqud4p8N29mY51pR
KSTjA4FYk6Z9EVMltyBHfdJs6RQzglKjxcNGdlrvacDfyFi79fGdiosVllrjfJM=
=3+V0
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
acpi, vhost, misc: fixes, features
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 01 Jun 2018 17:25:19 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (31 commits)
vhost-blk: turn on pre-defined RO feature bit
ACPI testing: test NFIT platform capabilities
nvdimm, acpi: support NFIT platform capabilities
tests/.gitignore: add entry for generated file
arch_init: sort architectures
ui: use local path for local headers
qga: use local path for local headers
colo: use local path for local headers
migration: use local path for local headers
usb: use local path for local headers
sd: fix up include
vhost-scsi: drop an unused include
ppc: use local path for local headers
rocker: drop an unused include
e1000e: use local path for local headers
ioapic: fix up includes
ide: use local path for local headers
display: use local path for local headers
trace: use local path for local headers
migration: drop an unused include
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No reason for vhost-scsi to pull in migration headers directly.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This is only half of the work, because the proxy devices (virtio-*-pci,
virtio-*-ccw, etc.) are still included unconditionally. It is still a
move in the right direction.
Based-on: <20180522194943.24871-1-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove those unneeded includes to speed up the compilation
process a little bit.
Code change produced with:
$ git grep '#include "sysemu/blockdev.h"' | \
cut -d: -f-1 | \
xargs egrep -L "(BlockInterfaceType|DriveInfo|drive_get|blk_legacy_dinfo|blockdev_mark_auto_del)" | \
xargs sed -i.bak '/#include "sysemu\/blockdev.h"/d'
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-15-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove those unneeded includes to speed up the compilation
process a little bit. (Continue 7eceff5b5a cleanup)
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-13-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As part of plumbing MemTxAttrs down to the IOMMU translate method,
add MemTxAttrs as an argument to the MemoryRegion valid.accepts
callback. We'll need this for subpage_accepts().
We could take the approach we used with the read and write
callbacks and add new a new _with_attrs version, but since there
are so few implementations of the accepts hook we just change
them all.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180521140402.23318-9-peter.maydell@linaro.org
When multi queue is enabled e.g. for a virtio-net device,
each queue pair will have a vhost_dev, and the only thing
shared between vhost devs currently is the chardev. This
patch introduces a vhost-user state structure which will
be shared by all vhost devs of the same virtio device.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
QEMU SCSI code makes assumptions about how the PROTECT and BYTCHK
works in the protocol, denying support for PI (Protection
Information) in case the guest OS requests it. However, in SCSI versions 2
and older, there is no PI concept in the protocol.
This means that when dealing with such devices:
- there is no PROTECT bit in byte 5 of the standard INQUIRY response. The
whole byte is marked as "Reserved";
- there is no RDPROTECT in byte 2 of READ. We have 'Logical Unit Number'
in this field instead;
- there is no VRPROTECT in byte 2 of VERIFY. We have 'Logical Unit Number'
in this field instead. This also means that the BYTCHK bit in this case
is not related to PI.
Since QEMU does not consider these changes, a SCSI passthrough using
a SCSI-2 device will not work. It will mistake these fields with
PI information and return Illegal Request SCSI SENSE thinking
that the driver is asking for PI support.
This patch fixes it by adding a new attribute called 'scsi_version'
that is read from the standard INQUIRY response of passthrough
devices. This allows for a version verification before applying
conditions related to PI that doesn't apply for older versions.
Reported-by: Dac Nguyen <dacng@us.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb@linux.vnet.ibm.com>
Message-Id: <20180327211451.14647-1-danielhb@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We would like to have different behavior for passthrough devices
depending on the SCSI version they expose. To prepare for that,
allow the user of emulated devices to specify the desired SCSI
level, and adjust the emulation according to the property value.
The next patch will set the level for scsi-block and scsi-generic
devices.
Based on a patch by Daniel Henrique Barboza
<danielhb@linux.vnet.ibm.com>.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some backends report big max_io_sectors. Making min_io_size the same
value in this case will make it impossible for guest to align memory,
therefore the disk may not be usable at all.
Do not enlarge them when they are zero.
Reported-by: David Gibson <dgibson@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20180327164141.19075-1-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the user does not have permissions to send ioctls to the device (due to
SELinux or cgroups, for example), the output can look like
qemu-kvm: -device scsi-block,drive=disk: cannot get SG_IO version number:
Operation not permitted. Is this a SCSI device?
but this is confusing because the ioctl was blocked _before_ the device
even received the SG_GET_VERSION_NUM ioctl. Therefore, for EPERM errors
the suggestion should be eliminated. To make that simpler, change the
code to use error_append_hint.
Reported-by: Ala Hino <ahino@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The global hack for creating SCSI devices has recently been removed,
but this apparently broke SCSI devices on some boards that were not
ready for this change yet. For the 40p machine you now get:
$ ppc64-softmmu/qemu-system-ppc64 -M 40p -cdrom x.iso
qemu-system-ppc64: -cdrom x.iso: machine type does not support if=scsi,bus=0,unit=2
Fix it by providing a lsi53c810_create() function that takes care
of calling scsi_bus_legacy_handle_cmdline() after creating the
corresponding SCSI controller.
Fixes: 1454509726
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The global hack for creating SCSI devices has recently been removed,
but this apparently broke SCSI devices on some boards that were not
ready for this change yet. For the pica61 machine you now get:
$ mips64-softmmu/qemu-system-mips64 -M pica61 -cdrom x.iso
qemu-system-mips64: -cdrom x.iso: machine type does not support if=scsi,bus=0,unit=2
Fix it by calling scsi_bus_legacy_handle_cmdline() after creating the
corresponding SCSI controller.
Fixes: 1454509726
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1520414644-11535-1-git-send-email-thuth@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A NDOB bit set to one specifies that the disk shall not transfer data
from the data-out buffer and shall process the command as if the data-out
buffer contained user data set to all zeroes.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After reviewing a patch from Philippe that removes block-backend.h
from hw/lm32/milkymist.c, I noticed that this header is included
unnecessarily in a lot of other files, too. Remove those unneeded
includes to speed up the compilation process a little bit.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1518684912-31637-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The calculation of the max_transfer atribute of BlockDriverState
makes considerations such as max_segments and transfer_length via
the BLKSECTGET ioctl (if available).
However, bl->max_transfer isn't considered when emulating the INQUIRY
'Block Limit' response to the scsi-hd devices. This leads to situations
where the declared max_sectors from the INQUIRY response is inconsistent
with the block limits, which isn't ideal. It can also be misleading to the
user that sets /sys/block/<dev>/queue/max_sectors_kb to a certain
value, then finds a different value in the guest OS for the same disk.
Following the same logic scsi_read_complete from scsi-generic.c does
when patching the response of the Block Limits VPD back to the guest,
change the max_io_sectors value of the emulated Block Limits VPD
response by considering the blk_get_max_transfer of the related
BlockDriverState. Use MIN_NOT_ZERO to be sure that the minimal
value is chosen.
Given that we're changing max_io_sectors, consider that min_io_sectors
and opt_io_sectors can't be greater than the new calculated value.
Signed-off-by: Daniel Henrique Barboza <danielhb@linux.vnet.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-Id: <20180306154411.18462-1-danielhb@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the main loop thread invokes .ioeventfd_stop() just as the vq handler
function begins in the IOThread then the handler may lose the race for
the AioContext lock. By the time the vq handler is able to acquire the
AioContext lock the ioeventfd has already been removed and the handler
isn't supposed to run anymore!
Use the new aio_wait_bh_oneshot() function to perform ioeventfd removal
from within the IOThread. This way no races with the vq handler are
possible.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20180307144205.20619-4-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Automatic creation of SCSI controllers for "-drive if=scsi" for x86
machines was quite a bad idea (see description of commit f778a82f0c
for details). This is marked as deprecated since QEMU v2.9.0, and as
far as I know, nobody complained that this is still urgently required
anymore. Time to remove this now.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1519123357-13225-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- new stats in virtio balloon
- virtio eventfd rework for boot speedup
- vhost memory rework for boot speedup
- fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJagxKDAAoJECgfDbjSjVRp5qAH/3gmgBaIzL3KRHd5i0RZifJv
PvyAVYgZd7h0+/1r9GM7guHKyEPZ08JtbHSm/HuDV4BD/Vf3/8joy8roExIfde2A
6k8fd6ANVQmE3t5zUxNXi9qiG4pO4xDIu4cMAbixzgN9x5ttlcfTw7fTT0e0VJxJ
8SN02/uCPPR/DY4/cpjah+slSyv6rBKT1v1ONy7djyRTYHi6h3Meoh05YfEALkwA
goxTKBZHi0L1IZ3HP/ZpXJDohQ5n2P09DX0fQgb8PgmW6WIWB/Qpi5pD53LZpMCV
n9waTF0U0ahneFd2FHo22QMMrwWvQyrjv+w5uXVr+qmHb/OyH2tUt7PgGF9+QKA=
=78s5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio,vhost,pci,pc: features, fixes and cleanups
- new stats in virtio balloon
- virtio eventfd rework for boot speedup
- vhost memory rework for boot speedup
- fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 13 Feb 2018 16:29:55 GMT
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (22 commits)
virtio-balloon: include statistics of disk/file caches
acpi-test: update FADT
lpc: drop pcie host dependency
tests: acpi: fix FADT not being compared to reference table
hw/pci-bridge: fix pcie root port's IO hints capability
libvhost-user: Support across-memory-boundary access
libvhost-user: Fix resource leak
virtio-balloon: unref the memory region before continuing
pci: removed the is_express field since a uniform interface was inserted
virtio-blk: enable multiple vectors when using multiple I/O queues
pci/bus: let it has higher migration priority
pci-bridge/i82801b11: clear bridge registers on platform reset
vhost: Move log_dirty check
vhost: Merge and delete unused callbacks
vhost: Clean out old vhost_set_memory and friends
vhost: Regenerate region list from changed sections list
vhost: Merge sections added to temporary list
vhost: Simplify ring verification checks
vhost: Build temporary section list and deref after commit
virtio: improve virtio devices initialization time
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
qemu-common.h includes qemu/option.h, but most places that include the
former don't actually need the latter. Drop the include, and add it
to the places that actually need it.
While there, drop superfluous includes of both headers, and
separate #include from file comment with a blank line.
This cleanup makes the number of objects depending on qemu/option.h
drop from 4545 (out of 4743) to 284 in my "build everything" tree.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-20-armbru@redhat.com>
[Semantic conflict with commit bdd6a90a9e in block/nvme.c resolved]
This cleanup makes the number of objects depending on qapi/error.h
drop from 1910 (out of 4743) to 1612 in my "build everything" tree.
While there, separate #include from file comment with a blank line,
and drop a useless comment on why qemu/osdep.h is included first.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-5-armbru@redhat.com>
[Semantic conflict with commit 34e304e975 resolved, OSX breakage fixed]
according to Eduardo Habkost's commit fd3b02c889 all PCIEs now implement
INTERFACE_PCIE_DEVICE so we don't need is_express field anymore.
Devices that implements only INTERFACE_PCIE_DEVICE (is_express == 1)
or
devices that implements only INTERFACE_CONVENTIONAL_PCI_DEVICE (is_express == 0)
where not affected by the change.
The only devices that were affected are those that are hybrid and also
had (is_express == 1) - therefor only:
- hw/vfio/pci.c
- hw/usb/hcd-xhci.c
- hw/xen/xen_pt.c
For those 3 I made sure that QEMU_PCI_CAP_EXPRESS is on in instance_init()
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Yoni Bettan <ybettan@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The virtio_bus_set_host_notifier function no longer calls
event_notifier_cleanup when a event notifier is removed.
The commit updates the code to match the new behavior and calls
virtio_bus_cleanup_host_notifier after the notifier was de-assign
and no longer in use.
This change is a preparation to allow executing the
virtio_bus_set_host_notifier function in a memory region
transaction.
Signed-off-by: Gal Hammer <ghammer@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Coverity doesn't like the ignored return value introduced in
9d3b155186 (hw/block: Fix the return type), and other callers are
converted already in ceff3e1f01.
This one was added lately in d9bcd6f7f2 and missed the train. Do it
now.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20180118025245.13042-1-famz@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Because usb-storage creates an internal scsi device, we should propagate
options. We already do so for bootindex etc, but failed to take care of
share-rw. Fix it in an apparent way: add a new parameter to
scsi_bus_legacy_add_drive and pass in s->conf.share_rw.
Cc: qemu-stable@nongnu.org
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-id: 20180117005222.4781-1-famz@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
scsi_write_same_complete() can retry the write if the request was
unaligned. Make sure to release the AioContext when that code path is
taken!
This patch fixes a hang when QEMU terminates after an unaligned WRITE
SAME request has been processed with dataplane. The hang occurs because
iothread_stop_all() cannot acquire the AioContext lock that was leaked
by the IOThread in scsi_write_same_complete().
Fixes: b9e413dd37 ("block: explicitly acquire aiocontext in aio callbacks that need it").
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: qemu-stable@nongnu.org
Reported-by: Cong Li <coli@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20180104142502.15175-1-stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the property to the device model, then parse it by calling
blkconf_apply_backend_options().
In addition to blk_set_perm(), the called function also handles error
options and wce. For error options we've already checked that the
default values are used, for wce we don't have the option either so it
is always the default (true). In other words there is no change of
behavior in these regards.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20171205151553.7834-1-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Extract the common parts of scsi_sense_buf_to_errno, scsi_convert_sense
and scsi_target_send_command's REQUEST SENSE handling into two new
functions scsi_parse_sense_buf and scsi_build_sense_buf.
Fix a bug in scsi_target_send_command along the way; the length was
written in buf[10] rather than buf[7].
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Fixes: b07fbce634 ("scsi-bus: correct responses for INQUIRY and REQUEST SENSE")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Scsi-block doesn't use the DEFINE_BLOCK_PROPERTIES() macro so it didn't
gain the share-rw back when it was added to all other storage devices.
This option is meaningful here, and need to be used when attaching a
shared storage to guest.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20171205071928.30242-1-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[Drop virtio_blk_data_plane_create() change that misinterprets return
value when the virtio transport does not support dataplane.
--Stefan]
Cc: John Snow <jsnow@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Mao Zhongyi <maozy.fnst@cn.fujitsu.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: e77848d3735ba590f23ffbf8094379c646c33d79.1511317952.git.maozy.fnst@cn.fujitsu.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
applied using ./scripts/clean-includes
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Ben Warren <ben@skyportsystems.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The bus pointer in PCIDevice is basically redundant with QOM information.
It's always initialized to the qdev_get_parent_bus(), the only difference
is the type.
Therefore this patch eliminates the field, instead creating a pci_get_bus()
helper to do the type mangling to derive it conveniently from the QOM
Device object underneath.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
A fair proportion of the users of pci_bus_num() want to get the bus
number on a specific device, so first have to look up the bus from the
device then call it. This adds a helper to do that (since we're going
to make looking up the bus slightly more verbose).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Commit 5c0919d020 ("virtio-scsi: Add virtqueue_size parameter allowing
virtqueue size to be set.") introduced a new parameter to virtio-scsi.
Later, commit 9200361060 ("vhost-user-scsi: add missing virtqueue_size
param") added that parameter to the new vhost-user-scsi interface but
neglected the existing vhost-scsi interface it was built on.
Apply the same change to vhost-scsi, so that we can boot a guest with
a device defined. This also avoids crashing a guest when hotplugging
a vhost-scsi device.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Message-id: 20171201151538.6844-2-farman@linux.vnet.ibm.com
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 5c0919d0 [1] introduced virtqueue_size parameter
for common virtio-scsi path, without updaing the vhost-user-scsi
code. vhost-user-scsi devices right now report size 0 for each vq.
This patch introduces virtqueue_size param to vhost-user-scsi,
that can now be set by the user. However, the most importantly, it
now has a default value of 128 (same as QEMU's virtio-scsi).
[1] 5c0919d0 ("virtio-scsi: Add virtqueue_size parameter
allowing virtqueue size to be set.")
Change-Id: I70e87eab702ebf1196c028dbf17d54fdc0c89a14
Signed-off-by: Dariusz Stojaczyk <dariuszx.stojaczyk@intel.com>
Message-Id: <1510676916-76409-1-git-send-email-dariuszx.stojaczyk@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This enables them to be used outside of esp.c.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Artyom Tarasenko <atar4qemu@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Logical block size of a SCSI disk should never be larger than
physical block size. From an ATA/SCSI perspective, it makes no sense
to have the logical block size greater than the physical block size,
and it cannot even be effectively expressed in the command set. The
whole point of adding the physical block size to the ATA/SCSI command
set was to communicate a desire for a larger block size (than logical),
while maintaining backwards compatibility with legacy 512 byte block
size.
When setting logical_block_size > physical_block_size, QEMU cannot express
it in READ CAPACITY(16) output, and all it can do is set the physical
block exponent to 0 (i.e. logical_block_size == physical_block_size).
Reporting the error properly, however, is better.
Signed-off-by: Mark Kanda <mark.kanda@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Message-Id: <1508185024-5840-1-git-send-email-mark.kanda@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add INTERFACE_CONVENTIONAL_PCI_DEVICE to all direct subtypes of
TYPE_PCI_DEVICE, except:
1) The ones that already have INTERFACE_PCIE_DEVICE set:
* base-xhci
* e1000e
* nvme
* pvscsi
* vfio-pci
* virtio-pci
* vmxnet3
2) base-pci-bridge
Not all PCI bridges are Conventional PCI devices, so
INTERFACE_CONVENTIONAL_PCI_DEVICE is added only to the subtypes
that are actually Conventional PCI:
* dec-21154-p2p-bridge
* i82801b11-bridge
* pbm-bridge
* pci-bridge
The direct subtypes of base-pci-bridge not touched by this patch
are:
* xilinx-pcie-root: Already marked as PCIe-only.
* pcie-pci-bridge: Already marked as PCIe-only.
* pcie-port: all non-abstract subtypes of pcie-port are already
marked as PCIe-only devices.
3) megasas-base
Not all megasas devices are Conventional PCI devices, so the
interface names are added to the subclasses registered by
megasas_register_types(), according to information in the
megasas_devices[] array.
"megasas-gen2" already implements INTERFACE_PCIE_DEVICE, so add
INTERFACE_CONVENTIONAL_PCI_DEVICE only to "megasas".
Acked-by: Alberto Garcia <berto@igalia.com>
Acked-by: John Snow <jsnow@redhat.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Change all devices that set is_express=1 to implement
INTERFACE_PCIE_DEVICE.
Cc: Keith Busch <keith.busch@intel.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: Dmitry Fleytman <dmitry@daynix.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: qemu-block@nongnu.org
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The following devices support both PCI Express and Conventional
PCI, by including special code to handle the QEMU_PCI_CAP_EXPRESS
flag and/or conditional pcie_endpoint_cap_init() calls:
* vfio-pci (is_express=1, but legacy PCI handled by
vfio_populate_device())
* vmxnet3 (is_express=0, but PCIe handled by vmxnet3_realize())
* pvscsi (is_express=0, but PCIe handled by pvscsi_realize())
* virtio-pci (is_express=0, but PCIe handled by
virtio_pci_dc_realize(), and additional legacy PCI code at
virtio_pci_realize())
* base-xhci (is_express=1, but pcie_endpoint_cap_init() call
is conditional on pci_bus_is_express(dev->bus)
* Note that xhci does not clear QEMU_PCI_CAP_EXPRESS like the
other hybrid devices
Cc: Dmitry Fleytman <dmitry@daynix.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The Linux kernel will query the SCSI "Block device characteristics"
VPD to determine the rotations per minute of the disk. If this has
the value 1, it is taken to be an SSD and so Linux sets the
'rotational' flag to 0 for the I/O queue and will stop using that
disk as a source of random entropy. Other operating systems may
also take into account rotation rate when setting up default
behaviour.
Mgmt apps should be able to set the rotation rate for virtualized
block devices, based on characteristics of the host storage in use,
so that the guest OS gets sensible behaviour out of the box. This
patch thus adds a 'rotation-rate' parameter for 'scsi-hd' and
'scsi-block' device types. For the latter, this parameter will be
ignored unless the host device has TYPE_DISK.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <20171004114008.14849-2-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Modify the pre_save method on VMStateDescription to return an int
rather than void so that it potentially can fail.
Changed zillions of devices to make them return 0; the only
case I've made it return non-0 is hw/intc/s390_flic_kvm.c that already
had an error_report/return case.
Note: If you add an error exit in your pre_save you must emit
an error_report to say why.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170925112917.21340-2-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
SunOS defines ESP (x86 register) in <sys/regset.h> as 7.
This fixes build on SmartOS (Joyent).
Signed-off-by: Kamil Rytarowski <n54@gmx.com>
Message-Id: <20170909142116.26816-1-n54@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Complete the transition by renaming this header, which was
shared by block/iscsi.c and the SCSI emulation code.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move more knowledge of SG_IO out of hw/scsi/scsi-generic.c, for
reusability.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move more knowledge of sense data format out of hw/scsi/scsi-bus.c
for reusability.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
util/scsi.c includes some SCSI code that is shared by block/iscsi.c and
hw/scsi, but the introduction of the persistent reservation helper
will add many more instances of this. There is also include/block/scsi.h,
which actually is not part of the core block layer.
The persistent reservation manager will also need a home. A scsi/
directory provides one for both the aforementioned shared code and
the PR manager code.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After introducing the scsi/ subdirectory, there will be a scsi_build_sense
function that is the same as scsi_req_build_sense but without needing
a SCSIRequest. The existing scsi_build_sense function gets in the way,
remove it.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This makes the werror/rerror options available on the scsi-block device,
to allow user specify error handling policy similar to scsi-hd.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20170821141008.19383-5-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to SPC-3 INQUIRY and REQUEST SENSE should return GOOD
even on unsupported LUNS.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Message-Id: <1503049022-14749-1-git-send-email-hare@suse.de>
Reported-by: Laszlo Ersek <lersek@redhat.com>
Fixes: ded6ddc5a7
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Since Linux switched to blk-mq as the default in Linux commit
5c279bd9e406 ("scsi: default to scsi-mq"), virtio-scsi LUNs consume
about 10x as much guest kernel memory.
This commit allows you to choose the virtqueue size for each
virtio-scsi-pci controller like this:
-device virtio-scsi-pci,id=scsi,virtqueue_size=16
The default is still 128 as before. Using smaller virtqueue_size
allows many more disks to be added to small memory virtual machines.
For a 1 vCPU, 500 MB, no swap VM I observed:
With scsi-mq enabled (upstream kernel): 175 disks
-"- ditto -"- virtqueue_size=64: 318 disks
-"- ditto -"- virtqueue_size=16: 775 disks
With scsi-mq disabled (kernel before 5c279bd9e406): 1755 disks
Note that to have any effect, this requires a kernel patch:
https://lkml.org/lkml/2017/8/10/689
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Message-Id: <20170810165255.20865-1-rjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The LUN0 emulation is just that, an emulation for a non-existing
LUN0. So we should be returning LUN_NOT_SUPPORTED for any request
coming from any other LUN.
And we should be aborting unhandled commands with INVALID OPCODE,
not LUN NOT SUPPORTED.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Message-Id: <1501835795-92331-4-git-send-email-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert a device model where initialization obviously
can't fail, make it implement realize() rather than init().
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Mao Zhongyi <maozy.fnst@cn.fujitsu.com>
Message-Id: <20170726084153.10121-2-maozy.fnst@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qemu_bh_new() is a wrapper around aio_bh_new(), which returns
null only when g_new() does. It doesn't. So remove the dead
error handling.
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Mao Zhongyi <maozy.fnst@cn.fujitsu.com>
Message-Id: <20170726084153.10121-1-maozy.fnst@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The only exception are groups of numers separated by symbols
'.', ' ', ':', '/', like 'ab.09.7d'.
This patch is made by the following:
> find . -name trace-events | xargs python script.py
where script.py is the following python script:
=========================
#!/usr/bin/env python
import sys
import re
import fileinput
rhex = '%[-+ *.0-9]*(?:[hljztL]|ll|hh)?(?:x|X|"\s*PRI[xX][^"]*"?)'
rgroup = re.compile('((?:' + rhex + '[.:/ ])+' + rhex + ')')
rbad = re.compile('(?<!0x)' + rhex)
files = sys.argv[1:]
for fname in files:
for line in fileinput.input(fname, inplace=True):
arr = re.split(rgroup, line)
for i in range(0, len(arr), 2):
arr[i] = re.sub(rbad, '0x\g<0>', arr[i])
sys.stdout.write(''.join(arr))
=========================
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-id: 20170731160135.12101-5-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In trace format '#' flag of printf is forbidden. Fix it to '0x%'.
This patch is created by the following:
check that we have a problem
> find . -name trace-events | xargs grep '%#' | wc -l
56
check that there are no cases with additional printf flags before '#'
> find . -name trace-events | xargs grep "%[-+ 0'I]+#" | wc -l
0
check that there are no wrong usage of '#' and '0x' together
> find . -name trace-events | xargs grep '0x%#' | wc -l
0
fix the problem
> find . -name trace-events | xargs sed -i 's/%#/0x%/g'
[Eric Blake noted that xargs grep '%[-+ 0'I]+#' should be xargs grep
"%[-+ 0'I]+#" instead so the shell quoting is correct.
--Stefan]
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170731160135.12101-3-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
With the move of some docs/ to docs/devel/ on ac06724a71,
no references were updated.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
On NetBSD, where tolower() and toupper() are implemented using an
array lookup, the compiler warns if you pass a plain 'char'
to these functions:
gdbstub.c:914:13: warning: array subscript has type 'char'
This reflects the fact that toupper() and tolower() give
undefined behaviour if they are passed a value that isn't
a valid 'unsigned char' or EOF.
We have qemu_tolower() and qemu_toupper() to avoid this problem;
use them.
(The use in scsi-generic.c does not trigger the warning because
it passes a uint8_t; we switch it anyway, for consistency.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com> for the s390 part.
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-id: 1500568290-7966-1-git-send-email-peter.maydell@linaro.org
If no drive=... option is passed (for an empty drive), we don't only
lack the BlockBackend normally created by parse_drive(), but we also
need to manually call blk_attach_dev().
This fixes at least a segfault when unplugging such devices, the bug
that they didn't show up in query-block, and probably some more
problems.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Convert all uses of error_report("warning:"... to use warn_report()
instead. This helps standardise on a single method of printing warnings
to the user.
All of the warnings were changed using these two commands:
find ./* -type f -exec sed -i \
's|error_report(".*warning[,:] |warn_report("|Ig' {} +
Indentation fixed up manually afterwards.
The test-qdev-global-props test case was manually updated to ensure that
this patch passes make check (as the test cases are case sensitive).
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Suggested-by: Thomas Huth <thuth@redhat.com>
Cc: Jeff Cody <jcody@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Lieven <pl@kamp.de>
Cc: Josh Durgin <jdurgin@redhat.com>
Cc: "Richard W.M. Jones" <rjones@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Greg Kurz <groug@kaod.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Peter Chubb <peter.chubb@nicta.com.au>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Alexander Graf <agraf@suse.de>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Greg Kurz <groug@kaod.org>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed by: Peter Chubb <peter.chubb@data61.csiro.au>
Acked-by: Max Reitz <mreitz@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Message-Id: <e1cfa2cd47087c248dd24caca9c33d9af0c499b0.1499866456.git.alistair.francis@xilinx.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
After converting to use DMA api for virtio devices, we should use
dma_as instead of address_space_memory. Otherwise it won't work if
IOMMU is enabled.
Fixes: commit 8607f5c307 ("virtio: convert to use DMA api")
Cc: qemu-stable@nongnu.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <1499170866-9068-1-git-send-email-jasowang@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This commit introduces a vhost-user device for SCSI. This is based
on the existing vhost-scsi implementation, but done over vhost-user
instead. It also uses a chardev to connect to the backend. Unlike
vhost-scsi (today), VMs using vhost-user-scsi can be live migrated.
To use it, start Qemu with a command line equivalent to:
qemu-system-x86_64 \
-chardev socket,id=vus0,path=/tmp/vus.sock \
-device vhost-user-scsi-pci,chardev=vus0,bus=pci.0,addr=...
A separate commit presents a sample application linked with libiscsi to
provide a backend for vhost-user-scsi.
Signed-off-by: Felipe Franciosi <felipe@nutanix.com>
Message-Id: <1488479153-21203-4-git-send-email-felipe@nutanix.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This ensures that the request is unref'ed properly, and avoids a
segmentation fault in the new qtest testcase that is added.
This is CVE-2017-9503.
Reported-by: Zhangyanyu <zyy4013@stu.ouc.edu.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Avoid TOC-TOU bugs by passing the frame_cmd down, and checking
cmd->dcmd_opcode instead of cmd->frame->header.frame_cmd.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This matches the qbus_set_hotplug_handler in realize, and it releases
the final reference to the embedded VirtIODevice so that it is
properly finalized.
A use-after-free is fixed with this patch, indirectly:
virtio_device_instance_finalize wasn't called at hot-unplug, and the
vdev->listener would be a dangling pointer in the global and the per
address space listener list. See also RHBZ 1449031.
Cc: qemu-stable@nongnu.org
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20170518102808.30046-1-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
lsi_mem_read/write() always return 0 about which their
callers actually don't care. Change the function type
to void.
Signed-off-by: Mao Zhongyi <maozy.fnst@cn.fujitsu.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This allows us to remove lots of includes of migration/migration.h
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
In order to introduce a new vhost-user-scsi host device type, it makes
sense to abstract part of vhost-scsi into a common parent class. This
commit does exactly that.
Signed-off-by: Felipe Franciosi <felipe@nutanix.com>
Message-Id: <1488479153-21203-3-git-send-email-felipe@nutanix.com>
A guest could set the message ring page count to zero, resulting in
infinite loop. Add check to avoid it.
Reported-by: YY Z <bigbird475958471@gmail.com>
Signed-off-by: P J P <ppandit@redhat.com>
Message-Id: <20170425130623.3649-1-ppandit@redhat.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
While reading magic sequence(MFI_SEQ) in megasas_mmio_write,
an off-by-one error could occur as 's->adp_reset' index is not
reset after reading the last sequence.
Reported-by: YY Z <bigbird475958471@gmail.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <20170424120634.12268-1-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When opt_xfer_len is zero, Linux ignores max_xfer_len erroneously.
While that obviously should be fixed, we do older guests a favor to
always filling in a value.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20170327142625.1249-1-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After the AioContext lock push down, there is a race between
virtio_scsi_dataplane_start and those "assert(s->ctx &&
s->dataplane_started)", because the latter doesn't isn't wrapped in
aio_context_acquire.
Reproducer is simply booting a Fedora guest with an empty
virtio-scsi-dataplane controller:
qemu-system-x86_64 \
-drive if=none,id=root,format=raw,file=Fedora-Cloud-Base-25-1.3.x86_64.raw \
-device virtio-scsi \
-device scsi-disk,drive=root,bootindex=1 \
-object iothread,id=io \
-device virtio-scsi-pci,iothread=io \
-net user,hostfwd=tcp::10022-:22 -net nic,model=virtio -m 2048 \
--enable-kvm
Fix this by moving acquire/release pairs from virtio_scsi_handle_*_vq to
their callers - and wrap the broken assertions in.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20170317061447.16243-3-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
They will be used in virtio-scsi-dataplane.c as well, so move them to
header.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20170317061447.16243-2-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
hw/scsi/trace-events lists cmd as the first parameter for both
megasas_iovec_overflow and megasas_iovec_underflow, but the caller
was mistakenly passing cmd->iov_size twice instead of the command
index. Also, trace_megasas_abort_invalid is called with parameters
in the wrong order. Broken since its introduction in commit
e8f943c3.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
When fetching request, it should read sizeof(*hdr), not the
pointer hdr.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Message-Id: <1489488980-130668-1-git-send-email-liqiang6-s@360.cn>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This makes all device emulations with a qdev drive property request
permissions on their BlockBackend. The only thing we block at this point
is resizing images for some devices that can't support it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Some devices allow a media change between read-only and read-write
media. They need to adapt the permissions in their .change_media_cb()
implementation, which can fail. So add an Error parameter to the
function.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
We want every user to be specific about the permissions it needs, so
we'll pass the initial permissions as parameters to blk_new(). A user
only needs to call blk_set_perm() if it wants to change the permissions
after the fact.
The permissions are stored in the BlockBackend and applied whenever a
BlockDriverState should be attached in blk_insert_bs().
This does not include actually choosing the right set of permissions
everywhere yet. Instead, the usual FIXME comment is added to each place
and will be addressed in individual patches.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
-----BEGIN PGP SIGNATURE-----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=/97H
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-block-2017-02-21' into staging
Changes to -drive without if= and with if=scsi
# gpg: Signature made Tue 21 Feb 2017 12:22:35 GMT
# gpg: using RSA key 0x3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-block-2017-02-21:
hw/i386: Deprecate -drive if=scsi with PC machine types
hw: Deprecate -drive if=scsi with non-onboard HBAs
hw/scsi: Concentrate -drive if=scsi auto-create in one place
hw: Drop superfluous special checks for orphaned -drive
blockdev: Make orphaned -drive fatal
blockdev: Improve message for orphaned -drive
hw/arm/highbank: Default -drive to if=ide instead of if=scsi
hw: Default -drive to if=none instead of scsi when scsi cannot work
hw: Default -drive to if=none instead of ide when ide cannot work
hw/arm/cubieboard hw/arm/xlnx-ep108: Fix units_per_default_bus
hw: Default -drive to if=ide explicitly where it works
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Block backends defined with "-drive if=T" with T other than "none" are
meant to be picked up by machine initialization code: a suitable
frontend gets created and wired up automatically.
Drives defined with if=scsi are also picked up by SCSI HBAs added with
-device, unlike other interface types. Deprecate this usage, as follows.
Create the frontends for onboard HBAs in machine initialization code,
exactly like we do for if=ide and other interface types. Change
scsi_legacy_handle_cmdline() to create a frontend only when it's still
missing, and warn that this usage is deprecated.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1487161136-9018-3-git-send-email-armbru@redhat.com>
The logic to create frontends for -drive if=scsi is in SCSI HBAs. For
all other interface types, it's in machine initialization code.
A few machine types create the SCSI HBAs necessary for that. That's
also not done for other interface types.
I'm going to deprecate these SCSI eccentricities. In preparation for
that, create the frontends in main() instead of the SCSI HBAs, by
calling new function scsi_legacy_handle_cmdline() there.
Note that not all SCSI HBAs create frontends. Take care not to change
that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1487161136-9018-2-git-send-email-armbru@redhat.com>
Acked-By: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170213135235.12274-16-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170213135235.12274-15-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This covers both file descriptor callbacks and polling callbacks,
since they execute related code.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170213135235.12274-14-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In virtio_queue_host_notifier_aio_poll, not all "!virtio_queue_empty()"
cases are making true progress.
Currently the offending one is virtio-scsi event queue, whose handler
does nothing if no event is pending. As a result aio_poll() will spin on
the "non-empty" VQ and take 100% host CPU.
Fix this by reporting actual progress from virtio queue aio handlers.
Reported-by: Ed Swierk <eswierk@skyportsystems.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Tested-by: Ed Swierk <eswierk@skyportsystems.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
msix_init() reports errors with error_report(), which is wrong when
it's used in realize(). The same issue was fixed for msi_init() in
commit 1108b2f. In order to make the API change as small as possible,
leave the return value check to later patch.
For some devices(like e1000e, vmxnet3, nvme) who won't fail because of
msix_init's failure, suppress the error report by passing NULL error
object.
Bonus: add comment for msix_init.
CC: Jiri Pirko <jiri@resnulli.us>
CC: Gerd Hoffmann <kraxel@redhat.com>
CC: Dmitry Fleytman <dmitry@daynix.com>
CC: Jason Wang <jasowang@redhat.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Hannes Reinecke <hare@suse.de>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Alex Williamson <alex.williamson@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When running with debug enabled, the scsi-generic cdb that is
dumped skips byte 0 of the command, which is the opcode. This
makes identifying which command is being issued/completed a
little difficult. Example:
0x00 0x00 0x01 0x00 0x00
scsi-generic: scsi_read_data 0x0
scsi-generic: Data ready tag=0x0 len=164
scsi-generic: scsi_read_data 0x0
scsi-generic: Command complete 0x0x10a42c60 tag=0x0 status=0
Improve this by adding a message prior to the loop, similar to
what exists for scsi-disk. Clean up a few other messages to be
more explicit of what is being represented. Example:
scsi-generic: Command: data=0x12 0x00 0x00 0x01 0x00 0x00
scsi-generic: scsi_read_data tag=0x0
scsi-generic: Data ready tag=0x0 len=164
scsi-generic: scsi_read_data tag=0x0
scsi-generic: Command complete 0x0x10a452d0 tag=0x0 status=0
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Message-Id: <20170120162527.66075-2-farman@linux.vnet.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 166dbda7e1 added some extra cases to a switch() such
that the existing code is intended to fall through the new
case statements. It's clear from the commit that this is
intentional, but less clear to subsequent readers of the
code, and not clear at all to static analysis tools like
Coverity. Add a /* fall through */ comment to indicate the
intent. (Fixes CID 1368287.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The vmstate_pci_device and vmstate_pcie_devices differ
just in the size of one buffer; combine the two using a _TEST
macro.
I think this is safe as long as everywhere which currently
uses either of these two uses the right type.
One thing that concerns me is that some places use pci_device_load/save
which does some irq mangling, but others just use the VMSTATE_PCI_DEVICE
macro - how are they getting the same irq mangling?
This passes a smoke test migrate of:
./x86_64-softmmu/qemu-system-x86_64 -M pc,accel=kvm -m 1024
./littlefed20.img -device e1000e -device virtio-net -device
e1000 -device virtio-rng -device megasas -device megasas-gen2 -device
ioh3420 -device nec-usb-xhci
to an unmodified qemu.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20161214195829.18241-1-dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
If a migration is already in progress and somebody attempts
to add a migration blocker, this should rightly fail.
Add an errp parameter and a retcode return value to migrate_add_blocker.
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Ashijeet Acharya <ashijeetacharya@gmail.com>
Message-Id: <1484566314-3987-5-git-send-email-ashijeetacharya@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Acked-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Merged with recent 'Allow invtsc migration' change
Current migration code cannot handle some data structures such as
QTAILQ in qemu/queue.h. Here we extend the signatures of put/get
in VMStateInfo so that customized handling is supported. put now
will return int type.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jianjun Duan <duanj@linux.vnet.ibm.com>
Message-Id: <1484852453-12728-2-git-send-email-duanj@linux.vnet.ibm.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The direction is wrong; scsi_block_is_passthrough returns
false for commands that *can* use sglists.
Reported-by: Zhang Qian <zhangqian@sangfor.com.cn>
Fixes: 8fdc7839e4
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the guest sets the sglist size to a value >=2GB, megasas_handle_dcmd
will return MFI_STAT_MEMORY_NOT_AVAILABLE without freeing the memory.
Avoid this by returning only the status from map_dcmd, and loading
cmd->iov_size in the caller.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, all virtio devices bypass IOMMU completely. This is because
address_space_memory is assumed and used during DMA emulation. This
patch converts the virtio core API to use DMA API. This idea is
- introducing a new transport specific helper to query the dma address
space. (only pci version is implemented).
- query and use this address space during virtio device guest memory
accessing when iommu platform (VIRTIO_F_IOMMU_PLATFORM) was enabled
for this device.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Amit Shah <amit.shah@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: qemu-block@nongnu.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The guest does not need to kick the virtqueue while we are processing
it. This reduces the number of vmexits during periods of heavy I/O.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20161201192652.9509-9-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
When a scsi-disk object receives VERIFY command with BYTCHK bit being zero,
scsi_block_is_passthrough returns false and finally makes req being proceeded
by scsi_block_dma_command. Because scsi_block_dma_command has removed process
of VERIFY, QEMU will abort in this function.
Reported-by: Junlian Bell <zhongjun@sangfor.com.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These will be used more as soon as the acquire/release is pushed down to
the ioeventfd handlers.
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQExBAABCAAbBQJYPFEQFBxwYm9uemluaUByZWRoYXQuY29tAAoJEL/70l94x66D
yF4H/3oBEgzDF9HbnSklknGhkPnOvYnNVKtJbHgk4SnZ1FlPSJLohuz15mXxbr+R
0MzWyQliHiBsAX8sMdvVVHm6YVy9JSABnsefhPUgM++1gT3+EhFsToZ9cWsAYOp7
Q4/hMc66ne0N5SWKjTlCzHfBxw3sPDvOoNYSVYjJYeASTSDQuyyVxRRWMYBFSUnD
p4m7dJCz+my8YXz6diTY8csxFRGmt49EtxtQBU1wBrFc+m8qn4UKaTXoqfcDEBe6
RceS9OAWrddv1Ds4OM/ZgD0BikYehYYnq9THvjWuqhTjHdKKYNeZAodqFJicEZmF
aAIZmhTASQo4fHuImtUja5ggYtU=
=Ht4d
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'bonzini/tags/for-upstream' into staging
Small fixes for rc2.
# gpg: Signature made Mon 28 Nov 2016 03:45:20 PM GMT
# gpg: using RSA key 0xBFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* bonzini/tags/for-upstream:
rules.mak: Use -r instead of -Wl, -r to fix building when PIE is default
migration/pcspk: Turn migration of pcspk off for 2.7 and older
migration/pcspk: Add a property to state if pcspk is migrated
pci-assign: sync MSI/MSI-X cap and table with PCIDevice
megasas: clean up and fix request completion/cancellation
megasas: do not call pci_dma_unmap after having freed the frame once
Message-id: 1480372837-109736-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
megasas_command_cancel is a callback; it should report the abort in
the frame, not try another abort! Compare for instance with
mptsas_request_cancelled.
So extract the common bits for request completion in a new function
megasas_complete_command, call it from both the .complete and .cancel
callbacks, and remove duplicate pieces from the DCMD path.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20161110152751.4267-2-pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 8cc4678 ("megasas: remove useless check for cmd->frame", 2016-07-17) was
wrong because I trusted Coverity too much. It turns out that there _is_ a
path through which cmd->frame can become NULL. After megasas_handle_frame's
switch (md->frame->header.frame_cmd), megasas_init_firmware can be called.
From there, megasas_reset_frames will call megasas_unmap_frame which resets
cmd->frame = NULL.
However, there is another bug to fix in there, because megasas_unmap_frame
is called again after setting the command status. In this case QEMU should
not do anything, instead it calls pci_dma_unmap again. Harmless, but
better fix it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This fixes SCSI adapter self-tests done in MIPS Jazz emulation,
broken since ff589551c8.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <1479508397-8443-1-git-send-email-hpoussin@reactos.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Dataplane has been omitting forever the step of setting ISR when
an interrupt is raised. This caused little breakage, because the
specification actually says that ISR may not be updated in MSI mode.
Some versions of the Windows drivers however didn't clear MSI mode
correctly, and proceeded using polling mode (using ISR, not the used
ring index!) for crashdump and hibernation. If it were just crashdump
and hibernation it would not be a big deal, but recent releases of
Windows do not really shut down, but rather log out and hibernate to
make the next startup faster. Hence, this manifested as a more serious
hang during shutdown with e.g. Windows 8.1 and virtio-win 1.8.0 RPMs.
Newer versions fixed this, while older versions do not use MSI at all.
The failure has always been there for virtio dataplane, but it became
visible after commits 9ffe337 ("virtio-blk: always use dataplane path
if ioeventfd is active", 2016-10-30) and ad07cd6 ("virtio-scsi: always
use dataplane path if ioeventfd is active", 2016-10-30) made virtio-blk
and virtio-scsi always use the dataplane code under KVM. The good news
therefore is that it was not a bug in the patches---they were doing
exactly what they were meant for, i.e. shake out remaining dataplane bugs.
The fix is not hard, so it's worth arranging for the broken drivers.
The virtio_should_notify+event_notifier_set pair that is common to
virtio-blk and virtio-scsi dataplane is replaced with a new public
function virtio_notify_irqfd that also sets ISR. The irqfd emulation
code now need not set ISR anymore, so virtio_irq is removed.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Version: GnuPG v2
iQEcBAABCAAGBQJYE2ULAAoJEMo1YkxqkXHGvvAH/iDPIAiwBXbndL3KhQTneSHn
ctd4I3VK1/VVTIBRJIetqETiWiAm/WoRhI9kBc/NrQxBFx3ko+fpSYFS2t6lJYnV
EX0vjTKjFhr05tOTQDH/SQtHdU5x/x2M8SsxqrCcTyLm5VDfdPeBlMBfSNMj/L2K
bwinANVEwr6LOM0h8weQ0SvOCa5MLII2p5ufGwKQmhUY5tgZvFlyPa+quDVisKoE
7CpLwWHmUQSNxUXSaru90osUJyk90wCcYxPpJN3YO1MHvpH4kG8DpZ8bnFqLAoNw
zkRdqIrlfntD+mKDqRU1y0GXxu9I4VK1UDcQyRFoSdMi2oHR+L018sQEjCYTAXo=
=n+CF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/famz/tags/for-upstream' into staging
# gpg: Signature made Fri 28 Oct 2016 15:47:39 BST
# gpg: using RSA key 0xCA35624C6A9171C6
# gpg: Good signature from "Fam Zheng <famz@redhat.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 5003 7CB7 9706 0F76 F021 AD56 CA35 624C 6A91 71C6
* remotes/famz/tags/for-upstream:
aio: convert from RFifoLock to QemuRecMutex
qemu-thread: introduce QemuRecMutex
iothread: release AioContext around aio_poll
block: only call aio_poll on the current thread's AioContext
qemu-img: call aio_context_acquire/release around block job
qemu-io: acquire AioContext
block: prepare bdrv_reopen_multiple to release AioContext
replication: pass BlockDriverState to reopen_backing_file
iothread: detach all block devices before stopping them
aio: introduce qemu_get_current_aio_context
sheepdog: use BDRV_POLL_WHILE
nfs: use BDRV_POLL_WHILE
nfs: move nfs_set_events out of the while loops
block: introduce BDRV_POLL_WHILE
qed: Implement .bdrv_drain
block: change drain to look only at one child at a time
block: add BDS field to count in-flight requests
mirror: use bdrv_drained_begin/bdrv_drained_end
blockjob: introduce .drain callback for jobs
replication: interrupt failover if the main device is closed
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Override start_ioeventfd and stop_ioeventfd to start/stop the
whole dataplane logic. This has some positive side effects:
- no need anymore for virtio_add_queue_aio (i.e. a revert of
commit 1c627137c1)
- no need anymore to switch from generic ioeventfd handlers to
dataplane
It detects some errors better:
$ qemu-system-x86_64 -object iothread,id=io \
-device virtio-scsi-pci,ioeventfd=off,iothread=io
qemu-system-x86_64: -device virtio-scsi-pci,ioeventfd=off,iothread=io:
ioeventfd is required for iothread
while previously it would have started just fine.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This simplifies the code and removes the ioeventfd_started
and ioeventfd_set_started callback. The only difference is
in how virtio-ccw handles an error---it doesn't disable
ioeventfd forever anymore. It was the only backend to do
so, and if desired this behavior should be implemented in
virtio-bus.c.
Instead of ioeventfd_started, the ioeventfd_assign callback now
determines whether the virtio bus supports host notifiers.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
aio_poll is not thread safe; for example bdrv_drain can hang if
the last in-flight I/O operation is completed in the I/O thread after
the main thread has checked bs->in_flight.
The bug remains latent as long as all of it is called within
aio_context_acquire/aio_context_release, but this will change soon.
To fix this, if bdrv_drain is called from outside the I/O thread,
signal the main AioContext through a dummy bottom half. The event
loop then only runs in the I/O thread.
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1477565348-5458-18-git-send-email-pbonzini@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
The hard-coded default alignment is BDRV_SECTOR_SIZE, however this is not
necessarily the case for all platforms. Use this as the default alignment for
all current callers.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Message-id: 1476445266-27503-2-git-send-email-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
Now all the usages of the old version of VMSTATE_VIRTIO_DEVICE are gone,
so we can get rid of the conditionals, and the old macro.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use the new VMSTATE_VIRTIO_DEVICE macro.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This error is caused by a buggy guest: let's switch the device to the
broken state instead of terminating QEMU.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The virtio_scsi_bad_req() function is called when a guest sends a
request with missing or ill-sized headers. This generally happens
when the virtio_scsi_parse_req() function returns an error.
With this patch, virtio_scsi_bad_req() will mark the device as broken,
detach the request from the virtqueue and free it, instead of forcing
QEMU to exit.
In nearly all locations where virtio_scsi_bad_req() is called, the only
thing to do next is to return to the caller.
The virtio_scsi_handle_cmd_req_prepare() function is an exception though.
It is called in a loop by virtio_scsi_handle_cmd_vq() and passed requests
freshly popped from a cmd virtqueue; virtio_scsi_handle_cmd_req_prepare()
does some sanity checks on the request and returns a boolean flag to
indicate whether the request should be queued or not. In the latter case,
virtio_scsi_handle_cmd_req_prepare() has detected a non-fatal error and
sent a response back to the guest.
We have now a new condition to take into account: the device is broken
and should stop all processing.
The return value of virtio_scsi_handle_cmd_req_prepare() is hence changed
to an int. A return value of zero means that the request should be queued.
Other non-fatal error cases where the request shoudn't be queued return
a negative errno (values are vaguely inspired by the error condition, but
the only goal here is to discriminate the case we're interested in).
And finally, if virtio_scsi_bad_req() was called, -EINVAL is returned. In
this case, virtio_scsi_handle_cmd_vq() detaches and frees already queued
requests, instead of submitting them.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A typo introduced in f19661c8 prevents qemu from building when configured
with --enable-trace-backend=dtrace.
Signed-off-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
All the other devices` .realize function name are xxx_realize, except this one.
cc: Michael S. Tsirkin <mst@redhat.com>
cc: Marcel Apfelbaum <marcel@redhat.com>
cc: Paolo Bonzini <pbonzini@redhat.com>
cc: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Vmware Paravirtual SCSI emulator while processing IO requests
could run into an infinite loop if 'pvscsi_ring_pop_req_descr'
always returned positive value. Limit IO loop to the ring size.
Cc: qemu-stable@nongnu.org
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <1473845952-30785-1-git-send-email-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When processing IO request in mptsas, it uses g_new to allocate
a 'req' object. If an error occurs before 'req->sreq' is
allocated, It could lead to an OOB write in mptsas_free_request
function. Use g_new0 to avoid it.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <1473684251-17476-1-git-send-email-ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
With an ejected block backend, blk_get_aio_context() would return
qemu_aio_context. In this case don't assert.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <1473848224-24809-3-git-send-email-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Even if tray is not open, it can be empty (blk_is_inserted() == false).
Handle both cases correctly by replacing the s->tray_open checks with
blk_is_available(), which is an AND of the two.
Also simplify successive checks of them into blk_is_available(), in a
couple cases.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <1473848224-24809-2-git-send-email-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This reverts commit 8cc46787b5.
It turns out that cmd->frame can be NULL and thus the commit
can cause a SIGSEGV
Reported-by: Holger Schranz <holger@fam-schranz.de>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In PVSCSI paravirtual SCSI bus, pvscsi_convert_sglist can take a very
long time or go into an infinite loop due to two different bugs:
1) the request descriptor data length is defined to be 64 bit. While
building SG list from a request descriptor, it gets truncated to 32bit
in routine 'pvscsi_convert_sglist'. This could lead to an infinite loop
situation large 'dataLen' values when data_length is cast to uint32_t and
chunk_size becomes always zero. Fix this by removing the incorrect cast.
2) pvscsi_get_next_sg_elem can be called arbitrarily many times if the
element has a zero length. Get out of the loop early when this happens,
by introducing an upper limit on the number of SG list elements.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <1473108643-12983-1-git-send-email-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These issues cause respectively a QEMU crash and a leak of 2 bytes of
stack. They were discovered by VictorV of 360 Marvel Team.
Reported-by: Tom Victor <i-tangtianwen@360.cm>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When LSI SAS1068 Host Bus emulator builds configuration page
headers, mptsas_config_pack() should assert that the size
fits in a byte. However, the size is expressed in 32-bit
units, so up to 1020 bytes fit. The assertion was only
allowing replies up to 252 bytes, so fix it.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <1472645167-30765-2-git-send-email-ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Vmware Paravirtual SCSI emulation uses command descriptors to
process SCSI commands. These descriptors come with their ring
buffers. A guest could set the page count for these rings to
an arbitrary value, leading to infinite loop or OOB access.
Add check to avoid it.
Reported-by: Tom Victor <vv474172261@gmail.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <1472626169-12989-1-git-send-email-ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Openstack Cinder assigns volume a 36 characters uuid as serial.
QEMU will shrinks the uuid to 20 characters, which does not match
the original uuid.
Note that there is no limit to the length of the serial number in
the SCSI spec. 20 was copy-pasted from virtio-blk which in turn was
copy-pasted from ATA; 36 is even more arbitrary. However, bumping it
up too much might cause issues (e.g. 252 seems to make sense because
then the maximum amount of returned data is 256; but who knows there's
no off-by-one somewhere for such a nicely rounded number).
Signed-off-by: Rony Weng <ronyweng@synology.com>
Message-Id: <1472457138-23386-1-git-send-email-ronyweng@synology.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This allows the creation of an empty scsi-cd device without manually
creating a BlockBackend.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Commit 2e2aa316 removed internal flag msi_in_use, but it
existed in vmstate. Restore it for migration to older QEMU
versions.
Reported-by: Amit Shah <amit.shah@redhat.com>
Suggested-by: Amit Shah <amit.shah@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Amit Shah <amit.shah@redhat.com>
Cc: Cao jin <caoj.fnst@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
My previous commit 2e2aa316 removed internal flag msi_in_use, which
exists in vmstate, use VMSTATE_UNUSED for migration compatibility.
Reported-by: Amit Shah <amit.shah@redhat.com>
Suggested-by: Amit Shah <amit.shah@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
- interrupt remapping for intel iommus
- a bunch of virtio cleanups
- fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXkQsqAAoJECgfDbjSjVRpanoIAJ9JVlc1aEjt9sa0cSBcs+NQ
J7JmgU9FqFsj+4FrNTouO3AxTjHurd1UAULP1WMPD+V3JpbnHct8r6SCBLQ5EBMN
VOjYo4DwWs1g+DqnQ9WZmbadu06XvYi/yiAKNUzWfZk0MR11D0D/S5hmarNKw0Kq
tGHeTWjGeY4WqFLV7m+qB4+cqkAByn6um99UtUvgLL05RgIEIP2IEMKYZ+rXvAa9
iGUvzqlO7mbq/+LbL18kaWywa4TCwbbd2eSGWaqhX4CuB62Rl33mWTXFcfaYhkyp
Z3FgwaJ09h0lAjSVEbyAuLFMfO/BnMcsoKqwl4xc4vkn/xBCqFtgH9JcEVm3O8U=
=ge2D
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, pci, virtio: new features, cleanups, fixes
- interrupt remapping for intel iommus
- a bunch of virtio cleanups
- fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 21 Jul 2016 18:49:30 BST
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (57 commits)
intel_iommu: avoid unnamed fields
virtio: Update migration docs
virtio-gpu: Wrap in vmstate
virtio-gpu: Use migrate_add_blocker for virgl migration blocking
virtio-input: Wrap in vmstate
9pfs: Wrap in vmstate
virtio-serial: Wrap in vmstate
virtio-net: Wrap in vmstate
virtio-balloon: Wrap in vmstate
virtio-rng: Wrap in vmstate
virtio-blk: Wrap in vmstate
virtio-scsi: Wrap in vmstate
virtio: Migration helper function and macro
virtio-serial: Remove old migration version support
virtio-net: Remove old migration version support
virtio-scsi: Replace HandleOutput typedef
Revert "mirror: Workaround for unexpected iohandler events during completion"
virtio-scsi: Call virtio_add_queue_aio
virtio-blk: Call virtio_add_queue_aio
virtio: Introduce virtio_add_queue_aio
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Forcibly convert it to a vmstate wrapper; proper conversion
comes later.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is a new common one in virtio.h, use it.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
AIO based handler is more appropriate here because it will then
cooperate with bdrv_drained_begin/end. It is needed by the coming
revert patch.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Change sector-based blk_discard(), blk_co_discard(), and
blk_aio_discard() to instead be byte-based blk_pdiscard(),
blk_co_pdiscard(), and blk_aio_pdiscard(). NBD gets a lot
simpler now that ignoring the unaligned portion of a
byte-based discard request is handled under the hood by
the block layer.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1468624988-423-6-git-send-email-eblake@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
megasas_enqueue_frame always returns with non-NULL cmd->frame.
Remove the "else" part as it is dead code.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* fixes to qemu-char and net exit
* FreeBSD fixes
* Other small bugfixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXhiZDAAoJEL/70l94x66DrGAH/10ZlIYugx6Ijn12qy3irmIC
hbMY6HWjvPlk8ZpAcPa3UXNQvqhTwqhSMXRiwp9aNPlRUqrXnDXZapQunJveKSAn
luLE8ISRKODz0W39qg6znyb4R1ipCGJWwjBCQmLWZuD7883JJ2DsykTATRx7yKQF
qsq9r/DPBTfD3vnOCTbqp0GeB80UFleTNm+K7cct8M1+WzfiwKeVHk9CAKy0fkTH
hS+YnV9UWYL6PR/w+uZ+2MfgH5er4X794+HaNbio0QJJbEZ2bsL4A3Prh7pUonN7
qJoCbT4W79scrnWQ40RbWRXOMfUk4J7gIMEZYar8z6NmqnamNZgxbWj3dv6pO+k=
=sz/L
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* SCSI scanner support
* fixes to qemu-char and net exit
* FreeBSD fixes
* Other small bugfixes
# gpg: Signature made Wed 13 Jul 2016 12:30:11 BST
# gpg: using RSA key 0xBFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream:
hostmem: detect host backend memory is being used properly
hostmem: fix QEMU crash by 'info memdev'
char: do not use atexit cleanup handler
net: do not use atexit for cleanup
slirp: use exit notifier for slirp_smb_cleanup
tap: use an exit notifier to call down_script
util: Fix MIN_NON_ZERO
qemu-sockets: use qapi_free_SocketAddress in cleanup
disas: avoid including everything in headers compiled from C++
json-streamer: fix double-free on exiting during a parse
main-loop: check return value before using pointer
Use "-s" instead of "--quiet" to resolve non-fatal build error on FreeBSD.
scsi-bus: Use longer sense buffer with scanners
scsi-bus: Add SCSI scanner support
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The rerror/werror policies are implemented in the devices, so that's
where they should be configured. In comparison to the old options in
-drive, the qdev properties are only added to those devices that
actually support them.
If the option isn't given (or "auto" is specified), the setting of the
BlockBackend is used for compatibility with the old options. For block
jobs, "auto" is the same as "enospc".
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
As cache.writeback is a BlockBackend property and as such more related
to the guest device than the BlockDriverState, we already removed it
from the blockdev-add interface. This patch adds the new way to set it,
as a qdev property of the corresponding guest device.
For example: -drive if=none,file=test.img,node-name=img
-device ide-hd,drive=img,write-cache=off
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Scanners can provide additional sense bytes beyond 18 bytes.
VueScan uses 32 bytes alloc length with Request Sense command.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@iki.fi>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add support for missing scanner specific SCSI commands and their xfer
lenghts as per ANSI spec section 15.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@iki.fi>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
