The AN505 and AN521 have the same layout of RAM; the AN524 does not.
Replace the current hard-coding of where the RAM is and which parts
of it are behind which MPCs with a data-driven approach.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-17-peter.maydell@linaro.org
The AN505 and AN521 have the same device layout, but the AN524 is
somewhat different. Allow for more than one PPCInfo array, which can
be selected based on the board type.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-16-peter.maydell@linaro.org
We create an OR gate to wire together the overflow IRQs for all the
UARTs on the board; this has to have twice the number of inputs as
there are UARTs, since each UART feeds it a TX overflow and an RX
overflow interrupt line. Replace the hardcoded '10' with a
calculation based on the size of the uart[] array in the
MPS2TZMachineState. (We rely on OR gate inputs that are never wired
up or asserted being treated as always-zero.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-15-peter.maydell@linaro.org
Move the specification of the IRQ information for the uart, ethernet,
dma and spi devices to the data structures. (The other devices
handled by the PPCPortInfo structures don't have any interrupt lines
we need to wire up.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-14-peter.maydell@linaro.org
The mps2-tz code uses PPCPortInfo data structures to define what
devices are present and how they are wired up. Currently we use
these to specify device types and addresses, but hard-code the
interrupt line wiring in each make_* helper function. This works for
the two boards we have at the moment, but the AN524 has some devices
with different interrupt assignments.
This commit adds the framework to allow PPCPortInfo structures to
specify interrupt numbers. We add an array of interrupt numbers to
the PPCPortInfo struct, and pass it through to the make_* helpers.
The following commit will change the make_* helpers over to using the
framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-13-peter.maydell@linaro.org
On the MPS2 boards, the first 32 interrupt lines are entirely
internal to the SSE; interrupt lines for devices outside the SSE
start at 32. In the application notes that document each FPGA image,
the interrupt wiring is documented from the point of view of the CPU,
so '0' is the first of the SSE's interrupts and the devices in the
FPGA image itself are '32' and up: so the UART 0 Receive interrupt is
32, the SPI #0 interrupt is 51, and so on.
Within our implementation, because the external interrupts must be
connected to the EXP_IRQ[0...n] lines of the SSE object, we made the
get_sse_irq_in() function take an irqno whose values start at 0 for
the first FPGA device interrupt. In this numbering scheme the UART 0
Receive interrupt is 0, the SPI #0 interrupt is 19, and so on.
The result of these two different numbering schemes has been that
half of the devices were wired up to the wrong IRQs: the UART IRQs
are wired up correctly, but the DMA and SPI devices were passing
start-at-32 values to get_sse_irq_in() and so being mis-connected.
Fix the bug by making get_sse_irq_in() take values specified with the
same scheme that the hardware manuals use, to avoid confusion.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-12-peter.maydell@linaro.org
The AN524 version of the SCC interface has different behaviour for
some of the CFG registers; implement it.
Each board in this family can have minor differences in the meaning
of the CFG registers, so rather than trying to specify all the
possible semantics via individual device properties, we make the
behaviour conditional on the part-number field of the SCC_ID register
which the board code already passes us.
For the AN524, the differences are:
* CFG3 is reserved rather than being board switches
* CFG5 is a new register ("ACLK Frequency in Hz")
* CFG6 is a new register ("Clock divider for BRAM")
We implement both of the new registers as reads-as-written.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-11-peter.maydell@linaro.org
The AN524 has more interrupt lines than the AN505 and AN521; make
numirq board-specific rather than a compile-time constant.
Since the difference is small (92 on the current boards and 95 on the
new one) we don't dynamically allocate the cpu_irq_splitter[] array
but leave it as a fixed length array whose size is the maximum needed
for any of the boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-10-peter.maydell@linaro.org
In the mps2-tz board code, we handle devices whose interrupt lines
must be wired to all CPUs by creating IRQ splitter devices for the
AN521, because it has 2 CPUs, but wiring the device IRQ directly to
the SSE/IoTKit input for the AN505, which has only 1 CPU.
We can avoid making an explicit check on the board type constant by
instead creating and using the IRQ splitters for any board with more
than 1 CPU. This avoids having to add extra cases to the
conditionals every time we add new boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-9-peter.maydell@linaro.org
Set the FPGAIO num-leds and have-switches properties explicitly
per-board, rather than relying on the defaults. The AN505 and AN521
both have the same settings as the default values, but the AN524 will
be different.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-8-peter.maydell@linaro.org
MPS3 boards have an extra SWITCH register in the FPGAIO block which
reports the value of some switches. Implement this, governed by a
property the board code can use to specify whether whether it exists.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-7-peter.maydell@linaro.org
The MPS2 board has 2 LEDs, but the MPS3 board has 10 LEDs. The
FPGAIO device is similar on both sets of boards, but the LED0
register has correspondingly more bits that have an effect. Add a
device property for number of LEDs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-6-peter.maydell@linaro.org
The AN505 and AN511 happen to share the same OSCCLK values, but the
AN524 will have a different set (and more of them), so split the
settings out to be per-board.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-5-peter.maydell@linaro.org
We were previously using the default OSCCLK settings, which are
correct for the older MPS2 boards (mps2-an385, mps2-an386,
mps2-an500, mps2-an511), but wrong for the mps2-an505 and mps2-511
implemented in mps2-tz.c. Now we're setting the values explicitly we
can fix them to be correct.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-4-peter.maydell@linaro.org
Currently the MPS2 SCC device implements a fixed number of OSCCLK
values (3). The variant of this device in the MPS3 AN524 board has 6
OSCCLK values. Switch to using a PROP_ARRAY, which allows board code
to specify how large the OSCCLK array should be as well as its
values.
With a variable-length property array, the SCC no longer specifies
default values for the OSCCLKs, so we must set them explicitly in the
board code. This defaults are actually incorrect for the an521 and
an505; we will correct this bug in a following patch.
This is a migration compatibility break for all the mps boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-3-peter.maydell@linaro.org
The AN524 has a different SYSCLK frequency from the AN505 and AN521;
make the SYSCLK frequency a field in the MPS2TZMachineClass rather
than a compile-time constant so we can support the AN524.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-2-peter.maydell@linaro.org
For a long time now the UI layer has guaranteed that the console
surface is always 32 bits per pixel, RGB. The TCX code already
assumes 32bpp, but it still has some checks of is_surface_bgr()
in an attempt to support 32bpp BGR. is_surface_bgr() will always
return false for the qemu_console_surface(), unless the display
device itself has deliberately created an alternate-format
surface via a function like qemu_create_displaysurface_from().
Drop the never-used BGR-handling code, and assert that we have
a 32-bit surface rather than just doing nothing if it isn't.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215102149.20513-1-peter.maydell@linaro.org
The macro draw_line_func is used only once; just expand it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210215103215.4944-10-peter.maydell@linaro.org
We only include the template header once, so just inline it into the
source file for the device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210215103215.4944-9-peter.maydell@linaro.org
Fix some minor coding style issues in the template header,
so checkpatch doesn't complain when we move the code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210215103215.4944-8-peter.maydell@linaro.org
The draw_line16_32() function in the omap_lcdc template header
includes an ifdef for the case where HOST_WORDS_BIGENDIAN matches
TARGET_WORDS_BIGENDIAN. This is trying to optimise for "source
bitmap and destination bitmap format match", but it is broken,
because in this function the formats don't match: the source is
16-bit colour and the destination is 32-bit colour, so a memcpy()
will produce corrupted graphics output. Drop the bogus ifdef.
This bug was introduced in commit ea644cf343, when we dropped
support for DEPTH values other than 32 from the template header.
The old #if line was
#if DEPTH == 16 && defined(HOST_WORDS_BIGENDIAN) == defined(TARGET_WORDS_BIGENDIAN)
and this was mistakenly changed to
#if defined(HOST_WORDS_BIGENDIAN) == defined(TARGET_WORDS_BIGENDIAN)
rather than deleting the #if as now having an always-false condition.
Fixes: ea644cf343
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210215103215.4944-7-peter.maydell@linaro.org
The omap_lcdc template header is already only included once, for
DEPTH==32, but it still has all the macro-driven parameterization
for other depths. Expand out all the macros in the header.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210215103215.4944-6-peter.maydell@linaro.org
The function tc6393xb_draw_graphic32() is called in exactly one place,
so just inline the function body at its callsite. This allows us to
drop the template header entirely.
The code move includes a single added space after 'for' to fix
the coding style.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210215103215.4944-5-peter.maydell@linaro.org
Now the template header is included only for BITS==32, expand
out all the macros that depended on the BITS setting.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215103215.4944-4-peter.maydell@linaro.org
For a long time now the UI layer has guaranteed that the console
surface is always 32 bits per pixel RGB. Remove the legacy dead
code from the tc6393xb display device which was handling the
possibility that the console surface was some other format.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215103215.4944-3-peter.maydell@linaro.org
For a long time now the UI layer has guaranteed that the console
surface is always 32 bits per pixel RGB. Remove the legacy dead
code from the milkymist display device which was handling the
possibility that the console surface was some other format.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215103215.4944-2-peter.maydell@linaro.org
We will move this code in the next commit. Clean it up
first to avoid checkpatch.pl errors.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210221222617.2579610-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
IDAU is specific to M-profile. KVM only supports A-profile.
Restrict this interface to TCG, as it is pointless (and
confusing) on a KVM-only build.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210221222617.2579610-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Section D6.7 of the ARM ARM states:
For the purpose of determining Tag Check Fault handling, unprivileged
load and store instructions are treated as if executed at EL0 when
executed at either:
- EL1, when the Effective value of PSTATE.UAO is 0.
- EL2, when both the Effective value of HCR_EL2.{E2H, TGE} is {1, 1}
and the Effective value of PSTATE.UAO is 0.
ARM has confirmed a defect in the pseudocode function
AArch64.TagCheckFault that makes it inconsistent with the above
wording. The remedy is to adjust references to PSTATE.EL in that
function to instead refer to AArch64.AccessUsesEL(acctype), so
that unprivileged instructions use SCTLR_EL1.TCF0 and TFSRE0_EL1.
The exception type for synchronous tag check faults remains unchanged.
This patch implements the described change by partially reverting
commits 50244cc76a and cc97b0019b.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219201820.2672077-1-pcc@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At the moment the following QEMU command line triggers an assertion
failure On xlnx-versal SOC:
qemu-system-aarch64 \
-machine xlnx-versal-virt -nographic -smp 2 -m 128 \
-fsdev local,id=shareid,path=${HOME}/work,security_model=none \
-device virtio-9p-device,fsdev=shareid,mount_tag=share \
-fsdev local,id=shareid1,path=${HOME}/Music,security_model=none \
-device virtio-9p-device,fsdev=shareid1,mount_tag=share1
qemu-system-aarch64: ../migration/savevm.c:860:
vmstate_register_with_alias_id:
Assertion `!se->compat || se->instance_id == 0' failed.
This problem was fixed on arm virt platform in commit f58b39d2d5
("virtio-mmio: format transport base address in BusClass.get_dev_path")
It works perfectly on arm virt platform. but there is still there on
xlnx-versal SOC.
The main difference between arm virt and xlnx-versal is they use
different way to create virtio-mmio qdev. on arm virt, it calls
sysbus_create_simple("virtio-mmio", base, pic[irq]); which will call
sysbus_mmio_map internally and assign base address to subsys device
mmio correctly. but xlnx-versal's implements won't do this.
However, xlnx-versal can't switch to sysbus_create_simple() to create
virtio-mmio device. It's because xlnx-versal's cpu use
VersalVirt.soc.fpd.apu.mr as it's memory. which is subregion of
system_memory. sysbus_create_simple will add virtio to system_memory,
which can't be accessed by cpu.
Besides, xlnx-versal can't add sysbus_mmio_map api call too, because
this will add memory region to system_memory, and it can't be added
to VersalVirt.soc.fpd.apu.mr again.
We can solve this by assign correct base address offset on dev_path.
This path was test on aarch64 virt & xlnx-versal platform.
Signed-off-by: schspa <schspa@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The STATUS register will be reset to IDLE in
cnpcm7xx_smbus_enter_reset(), no need to preset
it in instance_init().
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210228224813.312532-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Always perform one call instead of two for 16-byte operands.
Use byte loads/stores directly into the vector register file
instead of extractions and deposits to a 64-bit local variable.
In order to easily receive pointers into the vector register file,
convert the helper to the gvec out-of-line signature. Move the
helper into vec_helper.c, where it can make use of H1 and clear_tail.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20210224230532.276878-1-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We hint the 'has_rpu' property is no longer required since commit
6908ec448b ("xlnx-zynqmp: Properly support the smp command line
option") which was released in QEMU v2.11.0.
Beside, this device is marked 'user_creatable = false', so the
only thing that could be setting the property is the board code
that creates the device.
Since the property is not user-facing, we can remove it without
going through the deprecation process.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210219144350.1979905-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a 10/100 ethernet device that has several features.
Only the ones needed by the Linux driver have been implemented.
See npcm7xx_emc.c for a list of unimplemented features.
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Avi Fishman <avi.fishman@nuvoton.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Doug Evans <dje@google.com>
Message-id: 20210218212453.831406-3-dje@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a 10/100 ethernet device that has several features.
Only the ones needed by the Linux driver have been implemented.
See npcm7xx_emc.c for a list of unimplemented features.
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Avi Fishman <avi.fishman@nuvoton.com>
Signed-off-by: Doug Evans <dje@google.com>
Message-id: 20210218212453.831406-2-dje@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Set ID_AA64PFR1_EL1.SSBS to 2 and ID_PFR2.SSBS to 1.
Signed-off-by: Rebecca Cran <rebecca@nuviainc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210216224543.16142-3-rebecca@nuviainc.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for FEAT_SSBS. SSBS (Speculative Store Bypass Safe) is an
optional feature in ARMv8.0, and mandatory in ARMv8.5.
Signed-off-by: Rebecca Cran <rebecca@nuviainc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210216224543.16142-2-rebecca@nuviainc.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let add 'max' cpu while work goes on adding newer CPU types than
Cortex-A72. This allows us to check SVE etc support.
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Acked-by: Leif Lindholm <leif@nuviainc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210216150122.3830863-3-marcin.juszkiewicz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This PR is a collection of RISC-V patches:
- Improvements to SiFive U OTP
- Upgrade OpenSBI to v0.9
- Support the QMP dump-guest-memory
- Add support for the SiFive SPI controller (sifive_u)
- Initial RISC-V system documentation
- A fix for the Goldfish RTC
- MAINTAINERS updates
- Support for high PCIe memory in the virt machine
-----BEGIN PGP SIGNATURE-----
iQEyBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAmBA8k8ACgkQIeENKd+X
cFRRMgf41R7Zn1ZSB9GHL3WgLDTPqpT4FAMpTnYRD7wPdspawl1SsHWBgaLNmJWk
dwSLhvHMM44pOVCQRqdkiRrp5t5fDEm6gdRKyNn5uzWFMn7ibYIjmg7OE+79onbN
VES4yTJwuskD/7JRNcrW6RytKRgzKs2au8NxxgtgXprSF0nM9wCu70z4T9XkLfjQ
cpJUUaUCw628uUic/nObTxMnaiEmq/C0qU9SRRKPYVRp7jceCsHMVRazqOgdM6uf
foNHi/uCNKy6I841+D8Po7h57s51LtT78JDRRVRPfWY+SRQyC5l8Eq3UtRPyg39p
7hhkiAKhG4rs8iCXKvMvTz0S//Cx
=BVLq
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20210304' into staging
RISC-V PR for 6.0
This PR is a collection of RISC-V patches:
- Improvements to SiFive U OTP
- Upgrade OpenSBI to v0.9
- Support the QMP dump-guest-memory
- Add support for the SiFive SPI controller (sifive_u)
- Initial RISC-V system documentation
- A fix for the Goldfish RTC
- MAINTAINERS updates
- Support for high PCIe memory in the virt machine
# gpg: Signature made Thu 04 Mar 2021 14:44:31 GMT
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20210304:
hw/riscv: virt: Map high mmio for PCIe
hw/riscv: virt: Limit RAM size in a 32-bit system
hw/riscv: virt: Drop the 'link_up' parameter of gpex_pcie_init()
hw/riscv: Drop 'struct MemmapEntry'
MAINTAINERS: Add a SiFive machine section
goldfish_rtc: re-arm the alarm after migration
docs/system: riscv: Add documentation for sifive_u machine
docs/system: Add RISC-V documentation
docs/system: Sort targets in alphabetical order
hw/riscv: sifive_u: Change SIFIVE_U_GEM_IRQ to decimal value
hw/riscv: sifive_u: Add QSPI2 controller and connect an SD card
hw/riscv: sifive_u: Add QSPI0 controller and connect a flash
hw/ssi: Add SiFive SPI controller support
hw/block: m25p80: Add various ISSI flash information
hw/block: m25p80: Add ISSI SPI flash support
target-riscv: support QMP dump-guest-memory
roms/opensbi: Upgrade from v0.8 to v0.9
hw/misc: sifive_u_otp: Use error_report() when block operation fails
target/riscv: Declare csr_ops[] with a known size
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some peripherals require 64-bit PCI address, so let's map the high
mmio space for PCIe.
For RV32, the address is hardcoded to below 4 GiB from the highest
accessible physical address. For RV64, the base address depends on
top of RAM and is aligned to its size which is using 16 GiB for now.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210220144807.819-5-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RV32 supports 34-bit physical address hence the maximum RAM size
should be limited. Limit the RAM size to 10 GiB, which leaves
some room for PCIe high mmio space.
For 32-bit host, this is not needed as machine->ram_size cannot
represent a RAM size that big. Use a #if size test to only do
the size limitation for the 64-bit host.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210220144807.819-4-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
`link_up` is never used in gpex_pcie_init(). Drop it.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210220144807.819-3-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
There is already a MemMapEntry type defined in hwaddr.h. Let's drop
the RISC-V defined `struct MemmapEntry` and use the existing one.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210220144807.819-2-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
After a migration the clock offset is updated, but we also
need to re-arm the alarm if needed.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201220112615.933036-7-laurent@vivier.eu
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds detailed documentation for RISC-V `sifive_u` machine,
including the following information:
- Supported devices
- Hardware configuration information
- Boot options
- Machine-specific options
- Running Linux kernel
- Running VxWorks kernel
- Running U-Boot, and with an alternate configuration
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Message-id: 20210126060007.12904-10-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Add RISC-V system emulator documentation for generic information.
`Board-specific documentation` and `RISC-V CPU features` are only
a placeholder and will be added in the future.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-9-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
