That's never a good place to stop QEMU process... Since now we have
both the machine done sanity check and also the hotplug handler, we
can safely remove this to avoid that.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20190916080718.3299-5-peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Instead of bailing out when trying to hotplug a vfio-pci device with
below configuration:
-device intel-iommu,caching-mode=off
With this we can return a warning message to the user via QMP/HMP and
the VM will continue to work after failing the hotplug:
(qemu) device_add vfio-pci,bus=root.3,host=05:00.0,id=vfio1
Error: Device assignment is not allowed without enabling caching-mode=on for Intel IOMMU.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20190916080718.3299-4-peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This check was previously only happened when the IOMMU is enabled in
the guest. It was always too late because the enabling of IOMMU
normally only happens during the boot of guest OS. It means that we
can bail out and exit directly during the guest OS boots if the
configuration of devices are not supported. Or, if the guest didn't
enable vIOMMU at all, then the user can use the guest normally but as
long as it reconfigure the guest OS to enable the vIOMMU then reboot,
the user will see the panic right after the reset when the next boot
starts.
Let's make this failure even earlier so that we force the user to use
caching-mode for vfio-pci devices when with the vIOMMU. So the user
won't get surprise at least during execution of the guest, which seems
a bit nicer.
This will affect some user who didn't enable vIOMMU in the guest OS
but was using vfio-pci and the vtd device in the past. However I hope
it's not a majority because not enabling vIOMMU with the device
attached is actually meaningless.
We still keep the old assertion for safety so far because the hotplug
path could still reach it, so far.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20190916080718.3299-2-peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
CONFIG_ACPI_PCI is a hard requirement of acpi-build.c, which is built
unconditionally for x86 target. Putting it in default-configs/ suggests
that it can be easily disabled, which isn't true.
Relocate the symbol with the other acpi-build.c requirements, under
'config PC'. This is similar to what is done for the arm 'virt' machine
type and CONFIG_ACPI_PCI
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Message-Id: <e73e6edff68fd30d69c6a1d02c9ef9192f773c63.1568049871.git.crobinso@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The clock move makes the guest knows about the paused time between the
'stop' and 'migrate' commands. This is an issue in an already-paused
VM because some side effects, like process stalls, could happen
after migration.
So, this patch checks the runstate of guest in the pre_save handler and
do not re-reads the clock in case of paused state (cold migration).
Signed-off-by: Maxiwell S. Garcia <maxiwell@linux.ibm.com>
Message-Id: <20190829210711.6570-1-maxiwell@linux.ibm.com>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Commit 176d2cda0 (i386/cpu: Consolidate die-id validity in smp context) added
new 'die-id' topology property to CPUs and exposed it via QMP command
query-hotpluggable-cpus, which broke -device/device_add cpu-foo for existing
users that do not support die-id/dies yet. That's would be fine if it happened
to new machine type only but it also happened to old machine types,
which breaks migration from old QEMU to the new one, for example following CLI:
OLD-QEMU -M pc-i440fx-4.0 -smp 1,max_cpus=2 \
-device qemu64-x86_64-cpu,socket-id=1,core-id=0,thread-id
is not able to start with new QEMU, complaining about invalid die-id.
After discovering regression, the patch
"pc: Don't make die-id mandatory unless necessary"
makes die-id optional so old CLI would work.
However it's not enough as new QEMU still exposes die-id via query-hotpluggbale-cpus
QMP command, so the users that started old machine type on new QEMU, using all
properties (including die-id) received from QMP command (as required), won't be
able to start old QEMU using the same properties since it doesn't support die-id.
Fix it by hiding die-id in query-hotpluggbale-cpus for all machine types in case
'-smp dies' is not provided on CLI or -smp dies = 1', in which case smp_dies == 1
and APIC ID is calculated in default way (as it was before DIE support) so we won't
need compat code as in both cases the topology provided to guest via CPUID is the same.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190902120222.6179-1-imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
nb_queue was not zeroed so that we no longer delivered events if a
previous guest left the device in an overflow state.
The state of absolute does not matter as the next vmmouse_update_handler
call will align it again.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Message-Id: <f056c7e5-fa74-469c-87f8-0f0925301b2d@web.de>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We have this issue reported when using libvirt to hotplug CPUs:
https://bugzilla.redhat.com/show_bug.cgi?id=1741451
Basically, libvirt is not copying die-id from
query-hotpluggable-cpus, but die-id is now mandatory.
We could blame libvirt and say it is not following the documented
interface, because we have this buried in the QAPI schema
documentation:
> Note: currently there are 5 properties that could be present
> but management should be prepared to pass through other
> properties with device_add command to allow for future
> interface extension. This also requires the filed names to be kept in
> sync with the properties passed to -device/device_add.
But I don't think this would be reasonable from us. We can just
make QEMU more flexible and let die-id to be omitted when there's
no ambiguity. This will allow us to keep compatibility with
existing libvirt versions.
Test case included to ensure we don't break this again.
Fixes: commit 176d2cda0d ("i386/cpu: Consolidate die-id validity in smp context")
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190816170750.23910-1-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The error message when die-id is omitted doesn't make sense:
$ qemu-system-x86_64 -smp 1,sockets=6,maxcpus=6 \
-device qemu64-x86_64-cpu,socket-id=1,core-id=0,thread-id=0
qemu-system-x86_64: -device qemu64-x86_64-cpu,socket-id=1,core-id=0,thread-id=0: \
Invalid CPU die-id: 4294967295 must be in range 0:0
Fix it, so it will now read:
qemu-system-x86_64: -device qemu64-x86_64-cpu,socket-id=1,core-id=0,thread-id=0: \
CPU die-id is not set
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190815183803.13346-3-ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Vanderson M. do Rosario <vandersonmr2@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The error message for die-id range validation is incorrect. Example:
$ qemu-system-x86_64 -smp 1,sockets=6,maxcpus=6 \
-device qemu64-x86_64-cpu,socket-id=1,die-id=1,core-id=0,thread-id=0
qemu-system-x86_64: -device qemu64-x86_64-cpu,socket-id=1,die-id=1,core-id=0,thread-id=0: \
Invalid CPU die-id: 1 must be in range 0:5
The actual range for die-id in this example is 0:0.
Fix the error message to use smp_dies and print the correct range.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190815183803.13346-2-ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Vanderson M. do Rosario <vandersonmr2@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move existing numa global numa_info (renamed as "nodes") into NumaState.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190809065731.9097-5-tao3.xu@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move existing numa global have_numa_distance into NumaState.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Liu Jingqi <jingqi.liu@intel.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190809065731.9097-4-tao3.xu@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add struct NumaState in MachineState and move existing numa global
nb_numa_nodes(renamed as "num_nodes") into NumaState. And add variable
numa_support into MachineClass to decide which submachines support NUMA.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190809065731.9097-3-tao3.xu@intel.com>
[ehabkost: include hw/boards.h again to fix build failures]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Device model is supposed to destroy IOREQ server for itself.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Acked-by: Paul Durrant <paul.durrant@citrix.com>
Message-Id: <1564428563-1006-1-git-send-email-igor.druzhinin@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
First ppc and spapr pull request for qemu-4.2. Includes:
* Some TCG emulation fixes and performance improvements
* Support for the mffsl instruction in TCG
* Added missing DPDES SPR
* Some enhancements to the emulation of the XIVE interrupt
controller
* Cleanups to spapr MSI management
* Some new suspend/resume infrastructure and a draft suspend
implementation for spapr
* New spapr hypercall for TPM communication (will be needed for
secure guests under an Ultravisor)
* Fix several memory leaks
And a few other assorted fixes.
-----BEGIN PGP SIGNATURE-----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=E+7d
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.2-20190821' into staging
ppc patch queue for 2019-08-21
First ppc and spapr pull request for qemu-4.2. Includes:
* Some TCG emulation fixes and performance improvements
* Support for the mffsl instruction in TCG
* Added missing DPDES SPR
* Some enhancements to the emulation of the XIVE interrupt
controller
* Cleanups to spapr MSI management
* Some new suspend/resume infrastructure and a draft suspend
implementation for spapr
* New spapr hypercall for TPM communication (will be needed for
secure guests under an Ultravisor)
* Fix several memory leaks
And a few other assorted fixes.
# gpg: Signature made Wed 21 Aug 2019 08:24:44 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.2-20190821: (42 commits)
ppc: Fix emulated single to double denormalized conversions
ppc: Fix emulated INFINITY and NAN conversions
ppc: conform to processor User's Manual for xscvdpspn
ppc: Add support for 'mffsl' instruction
target/ppc: Add Directed Privileged Door-bell Exception State (DPDES) SPR
spapr/xive: Mask the EAS when allocating an IRQ
spapr: Implement better workaround in spapr-vty device
spapr/irq: Drop spapr_irq_msi_reset()
spapr/pci: Free MSIs during reset
spapr/pci: Consolidate de-allocation of MSIs
ppc: remove idle_timer logic
spapr: Implement ibm,suspend-me
i386: use machine class ->wakeup method
machine: Add wakeup method to MachineClass
ppc/xive: Improve 'info pic' support
ppc/xive: Provide silent escalation support
ppc/xive: Provide unconditional escalation support
ppc/xive: Provide escalation support
ppc/xive: Provide backlog support
ppc/xive: Implement TM_PULL_OS_CTX special command
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190709152053.16670-2-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Rebased onto merge commit 95a9457fd44; missed instances of qom/cpu.h
in comments replaced]
Move the i386 suspend_wakeup logic out of the fallback path, and into
the new ->wakeup method.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20190722061752.22114-1-npiggin@gmail.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add 4.2 machine types for arm/i440fx/q35/s390x/spapr.
For i440fx and q35, unversioned cpu models are still translated
to -v1, as 0788a56bd1 ("i386: Make unversioned CPU models be
aliases") states this should only transition to the latest cpu
model version in 4.3 (or later).
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190724103524.20916-1-cohuck@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In order to reduce the memory footprint we map into memory
the initrd using g_mapped_file_new() instead of reading it.
In this way we can share the initrd pages between multiple
instances of QEMU.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20190724143105.307042-4-sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
sysemu/sysemu.h is a rather unfocused dumping ground for stuff related
to the system-emulator. Evidence:
* It's included widely: in my "build everything" tree, changing
sysemu/sysemu.h still triggers a recompile of some 1100 out of 6600
objects (not counting tests and objects that don't depend on
qemu/osdep.h, down from 5400 due to the previous two commits).
* It pulls in more than a dozen additional headers.
Split stuff related to run state management into its own header
sysemu/runstate.h.
Touching sysemu/sysemu.h now recompiles some 850 objects. qemu/uuid.h
also drops from 1100 to 850, and qapi/qapi-types-run-state.h from 4400
to 4200. Touching new sysemu/runstate.h recompiles some 500 objects.
Since I'm touching MAINTAINERS to add sysemu/runstate.h anyway, also
add qemu/main-loop.h.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-30-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
[Unbreak OS-X build]
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/qdev-core.h includes sysemu/sysemu.h since recent commit e965ffa70a
"qdev: add qdev_add_vm_change_state_handler()". This is a bad idea:
hw/qdev-core.h is widely included.
Move the declaration of qdev_add_vm_change_state_handler() to
sysemu/sysemu.h, and drop the problematic include from hw/qdev-core.h.
Touching sysemu/sysemu.h now recompiles some 1800 objects.
qemu/uuid.h also drops from 5400 to 1800. A few more headers show
smaller improvement: qemu/notify.h drops from 5600 to 5200,
qemu/timer.h from 5600 to 4500, and qapi/qapi-types-run-state.h from
5500 to 5000.
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20190812052359.30071-28-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
hw/boards.h pulls in almost 60 headers. The less we include it into
headers, the better. As a first step, drop superfluous inclusions,
and downgrade some more to what's actually needed. Gets rid of just
one inclusion into a header.
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-23-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing qemu/main-loop.h triggers a
recompile of some 5600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h). It includes block/aio.h,
which in turn includes qemu/event_notifier.h, qemu/notify.h,
qemu/processor.h, qemu/qsp.h, qemu/queue.h, qemu/thread-posix.h,
qemu/thread.h, qemu/timer.h, and a few more.
Include qemu/main-loop.h only where it's needed. Touching it now
recompiles only some 1700 objects. For block/aio.h and
qemu/event_notifier.h, these numbers drop from 5600 to 2800. For the
others, they shrink only slightly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-21-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
In my "build everything" tree, changing sysemu/reset.h triggers a
recompile of some 2600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
The main culprit is hw/hw.h, which supposedly includes it for
convenience.
Include sysemu/reset.h only where it's needed. Touching it now
recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-9-armbru@redhat.com>
Some of the generated qapi-types-MODULE.h are included all over the
place. Changing a QAPI type can trigger massive recompiling. Top
scorers recompile more than 1000 out of some 6600 objects (not
counting tests and objects that don't depend on qemu/osdep.h):
6300 qapi/qapi-builtin-types.h
5700 qapi/qapi-types-run-state.h
3900 qapi/qapi-types-common.h
3300 qapi/qapi-types-sockets.h
3000 qapi/qapi-types-misc.h
3000 qapi/qapi-types-crypto.h
3000 qapi/qapi-types-job.h
3000 qapi/qapi-types-block-core.h
2800 qapi/qapi-types-block.h
1300 qapi/qapi-types-net.h
Clean up headers to include generated QAPI headers only where needed.
Impact is negligible except for hw/qdev-properties.h.
This header includes qapi/qapi-types-block.h and
qapi/qapi-types-misc.h. They are used only in expansions of property
definition macros such as DEFINE_PROP_BLOCKDEV_ON_ERROR() and
DEFINE_PROP_OFF_AUTO(). Moving their inclusion from
hw/qdev-properties.h to the users of these macros avoids pointless
recompiles. This is how other property definition macros, such as
DEFINE_PROP_NETDEV(), already work.
Improves things for some of the top scorers:
3600 qapi/qapi-types-common.h
2800 qapi/qapi-types-sockets.h
900 qapi/qapi-types-misc.h
2200 qapi/qapi-types-crypto.h
2100 qapi/qapi-types-job.h
2100 qapi/qapi-types-block-core.h
270 qapi/qapi-types-block.h
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-3-armbru@redhat.com>
Show PCIe host bridge PNP id with PCI host bridge as a compatible id
when expanding a pcie bus.
Cc: qemu-stable@nongnu.org
Signed-off-by: Evgeny Yakovlev <wrfsh@yandex-team.ru>
Message-Id: <1563526469-15588-1-git-send-email-wrfsh@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When very large regions (32GB sized in our case, PCI pass-through of GPUs)
are compared substraction result does not fit into gint.
As a result crs_replace_with_free_ranges does not get sorted ranges and
incorrectly computes PCI64 free space regions. Which then makes linux
guest complain about device and PCI64 hole intersection and device
becomes unusable.
Fix that by returning exactly fitting ranges.
Also fix indentation of an entire crs_replace_with_free_ranges to make
checkpatch happy.
Cc: qemu-stable@nongnu.org
Signed-off-by: Evgeny Yakovlev <wrfsh@yandex-team.ru>
Message-Id: <1563466463-26012-1-git-send-email-wrfsh@yandex-team.ru>
Signed-off-by: Evgeny Yakovlev <wrfsh@yandex-team.ru>
Commit 97fd1ea8c1 broke the build for --without-default-devices as
VMMOUSE depends on VMPORT.
Fixes: 97fd1ea8c1
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
vmport device is not included when CONFIG_VMPORT is disabled, hence
QEMU fails with the following error:
`Unknown device 'vmport' for bus 'ISA': unknown.`
v2: imply VMPORT (Paolo Bonzini )
Signed-off-by: Julio Montes <julio.montes@intel.com>
Message-Id: <20190712160257.18270-1-julio.montes@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJdH7FgAAoJEL/70l94x66DdUUH+gLr/ZdjLIdfYy9cjcnevf4E
cJlxdaW9KvUsK2uVgqQ/3b1yF+GCGk10n6n8ZTIbClhs+6NpqEMz5O3FA/Na6FGA
48M2DwJaJ2H9AG/lQBlSBNUZfLsEJ9rWy7DHvNut5XMJFuWGwdtF/jRhUm3KqaRq
vAaOgcQHbzHU9W8r1NJ7l6pnPebeO7S0JQV+82T/ITTz2gEBDUkJ36boO6fedkVQ
jLb9nZyG3CJXHm2WlxGO4hkqbLFzURnCi6imOh2rMdD8BCu1eIVl59tD1lC/A0xv
Pp3xXnv9SgJXsV4/I/N3/nU85ZhGVMPQZXkxaajHPtJJ0rQq7FAG8PJMEj9yPe8=
=poke
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
Bugfixes.
# gpg: Signature made Fri 05 Jul 2019 21:21:52 BST
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream:
ioapic: use irq number instead of vector in ioapic_eoi_broadcast
hw/i386: Fix linker error when ISAPC is disabled
Makefile: generate header file with the list of devices enabled
target/i386: kvm: Fix when nested state is needed for migration
minikconf: do not include variables from MINIKCONF_ARGS in config-all-devices.mak
target/i386: fix feature check in hyperv-stub.c
ioapic: clear irq_eoi when updating the ioapic redirect table entry
intel_iommu: Fix unexpected unmaps during global unmap
intel_iommu: Fix incorrect "end" for vtd_address_space_unmap
i386/kvm: Fix build with -m32
checkpatch: do not warn for multiline parenthesized returned value
pc: fix possible NULL pointer dereference in pc_machine_get_device_memory_region_size()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
v2: include config-devices.h to use CONFIG_IDE_ISA
Message-Id: <20190705143554.10295-2-julio.montes@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Julio Montes <julio.montes@intel.com>
This is an replacement work of Yan Zhao's patch:
https://www.mail-archive.com/qemu-devel@nongnu.org/msg625340.html
vtd_address_space_unmap() will do proper page mask alignment to make
sure each IOTLB message will have correct masks for notification
messages (2^N-1), but sometimes it can be expanded to even supercede
the registered range. That could lead to unexpected UNMAP of already
mapped regions in some other notifiers.
Instead of doing mindless expension of the start address and address
mask, we split the range into smaller ones and guarantee that each
small range will have correct masks (2^N-1) and at the same time we
should also try our best to generate as less IOTLB messages as
possible.
Reported-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Yan Zhao <yan.y.zhao@intel.com>
Message-Id: <20190624091811.30412-3-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
IOMMUNotifier is with inclusive ranges, so we should check
against (VTD_ADDRESS_SIZE(s->aw_bits) - 1).
Signed-off-by: Yan Zhao <yan.y.zhao@intel.com>
[peterx: split from another bigger patch]
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20190624091811.30412-2-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
QEMU will crash when device-memory-region-size property is read if ms->device_memory
wasn't initialized yet.
Crash can be reproduced with:
$QEMU -preconfig -qmp unix:qmp_socket,server,nowait &
./scripts/qmp/qom-get -s qmp_socket /machine.device-memory-region-size
Instead of crashing return 0 if ms->device_memory hasn't been initialized.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1560174635-22602-1-git-send-email-imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will make unversioned CPU models behavior depend on the
machine type:
* "pc-*-4.0" and older will not report them as aliases.
This is done to keep compatibility with older QEMU versions
after management software starts translating aliases.
* "pc-*-4.1" will translate unversioned CPU models to -v1.
This is done to keep compatibility with existing management
software, that still relies on CPU model runnability promises.
* "none" will translate unversioned CPU models to their latest
version. This is planned become the default in future machine
types (probably in pc-*-4.3).
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190628002844.24894-8-ehabkost@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
For PC target, users could configure the number of dies per one package
via command line with this patch, such as "-smp dies=2,cores=4".
The parsing rules of new cpu-topology model obey the same restrictions/logic
as the legacy socket/core/thread model especially on missing values computing.
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Message-Id: <20190620054525.37188-4-like.xu@linux.intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
To make smp_parse() more flexible and expansive, a smp_parse function
pointer is added to MachineClass that machine types could override.
The generic smp_parse() code in vl.c is moved to hw/core/machine.c, and
become the default implementation of MachineClass::smp_parse. A PC-specific
function called pc_smp_parse() has been added to hw/i386/pc.c, which in
this patch changes nothing against the default one .
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190620054525.37188-3-like.xu@linux.intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Legacy '-numa node,mem' option has a number of issues and mgmt often
defaults to it. Unfortunately it's no possible to replace it with
an alternative '-numa memdev' without breaking migration compatibility.
What's possible though is to deprecate it, keeping option working with
old machine types only.
In order to help users to find out if being deprecated CLI option
'-numa node,mem' is still supported by particular machine type, add new
"numa-mem-supported" property to output of query-machines.
"numa-mem-supported" is set to 'true' for machines that currently support
NUMA, but it will be flipped to 'false' later on, once deprecation period
expires and kept 'true' only for old machine types that used to support
the legacy option so it won't break existing configuration that are using
it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1560172207-378962-1-git-send-email-imammedo@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
QEMU will crash when device-memory-region-size property is read if ms->device_memory
wasn't initialized yet.
Crash can be reproduced with:
$QEMU -preconfig -qmp unix:qmp_socket,server,nowait &
./scripts/qmp/qom-get -s qmp_socket /machine.device-memory-region-size
Instead of crashing return 0 if ms->device_memory hasn't been initialized.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190624090200.5383-1-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
In new sockets/dies/cores/threads model, the apicid of logical cpu could
imply die level info of guest cpu topology thus x86_apicid_from_cpu_idx()
need to be refactored with #dies value, so does apicid_*_offset().
To keep semantic compatibility, the legacy pkg_offset which helps to
generate CPUIDs such as 0x3 for L3 cache should be mapping to die_offset.
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Message-Id: <20190612084104.34984-5-like.xu@linux.intel.com>
[ehabkost: squash unit test patch]
Message-Id: <20190612084104.34984-6-like.xu@linux.intel.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The field die_id (default as 0) and has_die_id are introduced to X86CPU.
Following the legacy smp check rules, the die_id validity is added to
the same contexts as leagcy smp variables such as hmp_hotpluggable_cpus(),
machine_set_cpu_numa_node(), cpu_slot_to_string() and pc_cpu_pre_plug().
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Message-Id: <20190612084104.34984-4-like.xu@linux.intel.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
To support multiple dies configuration on PCMachine, the best place to
set CPUX86State->nr_dies with requested PCMachineState->smp_dies is in
pc_new_cpu() and pc_cpu_pre_plug(). Refactoring pc_new_cpu() is applied
and redundant parameter "const char *typename" would be removed.
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Message-Id: <20190612084104.34984-3-like.xu@linux.intel.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The die-level as the first PC-specific cpu topology is added to the leagcy
cpu topology model, which has one die per package implicitly and only the
numbers of sockets/cores/threads are configurable.
In the new model with die-level support, the total number of logical
processors (including offline) on board will be calculated as:
#cpus = #sockets * #dies * #cores * #threads
and considering compatibility, the default value for #dies would be
initialized to one in x86_cpu_initfn() and pc_machine_initfn().
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Message-Id: <20190612084104.34984-2-like.xu@linux.intel.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The global smp variables in i386 are replaced with smp machine properties.
To avoid calling qdev_get_machine() as much as possible, some related funtions
for acpi data generations are refactored. No semantic changes.
A local variable of the same name would be introduced in the declaration
phase if it's used widely in the context OR replace it on the spot if it's
only used once. No semantic changes.
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Message-Id: <20190518205428.90532-8-like.xu@linux.intel.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
To get rid of the global smp_* variables we're currently using, it's recommended
to pass MachineState in the list of incoming parameters for functions that use
global smp variables, thus some redundant parameters are dropped. It's applied
for legacy smbios_*(), *_machine_reset(), hot_add_cpu() and mips *_create_cpu().
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190518205428.90532-3-like.xu@linux.intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
virtio-pmem support.
libvhost user mq support.
A bunch of fixes all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEbBAABAgAGBQJdHmkBAAoJECgfDbjSjVRpEAIH+Kmy8n5Et9NzsnmNqHAiC/pg
3V5wGyp9M4ZJVPXC0z/Q1sYJ3YYP6dBd4tjj2/7LzYZSlqlQIs83UlQCo0XTiliH
/jZD/IaAZABnfB7vAeZW67WNT2a20xG2Jr83083lSaDUI/pfIdvbMelIbBLmo/kd
tWdAAWT0kcGYjyz4xQQgtAH6zAQUleKE7ECUJ2TpJQbSMLxdI/YTaoYqek471YdP
ju5OLBO3WbNkSE9JYz4MJqTudYK0sKu568UqBVF8JdpFd5Cv+X/OI+bCsc4QK8KN
DTtFVVvbm1KGPSceqc9rwsDjO4Wd8ThvuZxrB029AahD6vT82F13IHpi/S29Fw==
=WAFb
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, pc, pci: features, fixes, cleanups
virtio-pmem support.
libvhost user mq support.
A bunch of fixes all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 04 Jul 2019 22:00:49 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (22 commits)
docs: avoid vhost-user-net specifics in multiqueue section
libvhost-user: implement VHOST_USER_PROTOCOL_F_MQ
libvhost-user: support many virtqueues
libvhost-user: add vmsg_set_reply_u64() helper
pc: Move compat_apic_id_mode variable to PCMachineClass
virtio: Don't change "started" flag on virtio_vmstate_change()
virtio: Make sure we get correct state of device on handle_aio_output()
virtio: Set "start_on_kick" on virtio_set_features()
virtio: Set "start_on_kick" for legacy devices
virtio: add "use-started" property
virtio-pci: fix missing device properties
pc: Support for virtio-pmem-pci
numa: Handle virtio-pmem in NUMA stats
hmp: Handle virtio-pmem when printing memory device infos
virtio-pci: Proxy for virtio-pmem
virtio-pmem: sync linux headers
virtio-pci: Allow to specify additional interfaces for the base type
virtio-pmem: add virtio device
pcie: minor cleanups for slot control/status
pcie: work around for racy guest init
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace the static variable with a PCMachineClass field. This
will help us eventually get rid of the pc_compat_*() init
functions.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190628200227.1053-1-ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Override the device hotplug handler to properly handle the memory device
part via virtio-pmem-pci callbacks from the machine hotplug handler and
forward to the actual PCI bus hotplug handler.
As PCI hotplug has not been properly factored out into hotplug handlers,
most magic is performed in the (un)realize functions. Also some PCI host
buses don't have a PCI hotplug handler at all yet, just to be sure that
we alway have a hotplug handler on x86, add a simple error check.
Unlocking virtio-pmem will unlock virtio-pmem-pci.
Signed-off-by: David Hildenbrand <david@redhat.com>
[ Disable virtio-pmem hotunplug ]
Signed-off-by: Pankaj Gupta <pagupta@redhat.com>
Message-Id: <20190619094907.10131-8-pagupta@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
xen-mapcache.c doesn't needs params.h.
xen-hvm.c uses defines available in params.h but so is xen_common.h
which is included before. HVM_PARAM_* flags are only needed to make
xc_hvm_param_{get,set} calls so including only xenctrl.h, which is
where the definition the function is, should be enough.
(xenctrl.h does include params.h)
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Message-Id: <20190618112341.513-4-anthony.perard@citrix.com>
Avoid using a variable length array.
We allocate the `dirty_bitmap' buffer only once when we start tracking
for dirty bits.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190618112341.513-5-anthony.perard@citrix.com>
Commit c87759ce87 fixed a regression affecting pc-q35 machines by
introducing a new pc-q35-4.0.1 machine version to be used instead
of pc-q35-4.0. The only purpose was to revert the default behaviour
of not using split irqchip, but the change also introduced the usual
hw_compat and pc_compat bits, and wired them for pc-q35 only.
This raises questions when it comes to add new compat properties for
4.0* machine versions of any architecture. Where to add them ? In
4.0, 4.0.1 or both ? Error prone. Another possibility would be to teach
all other architectures about 4.0.1. This solution isn't satisfying,
especially since this is a pc-q35 specific issue.
It turns out that the split irqchip default is handled in the machine
option function and doesn't involve compat lists at all.
Drop all the 4.0.1 compat lists and use the 4.0 ones instead in the 4.0.1
machine option function.
Move the compat props that were added to the 4.0.1 since c87759ce87 to
4.0.
Even if only hw_compat_4_0_1 had an impact on other architectures,
drop pc_compat_4_0_1 as well for consistency.
Fixes: c87759ce87 "q35: Revert to kernel irqchip"
Suggested-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <156051774276.244890.8660277280145466396.stgit@bahia.lan>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Representing Hyper-V properties as bits will allow us to check features
and dependencies between them in a natural way.
Suggested-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20190517141924.19024-2-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch changes the handling of the mmconfig area. Thanks to the
pci(e) expander devices we already have the logic to exclude address
ranges from PCI0._CRS. We can simply add the mmconfig address range
to the list get it excluded as well.
With that in place we can go with a fixed pci hole which covers the
whole area from the end of (low) ram to the ioapic.
This will make the whole logic alot less fragile. No matter where the
firmware places the mmconfig xbar, things should work correctly. The
guest also gets a bit more PCI address space (seabios boot):
# cat /proc/iomem
[ ... ]
7ffdd000-7fffffff : reserved
80000000-afffffff : PCI Bus 0000:00 <<-- this is new
b0000000-bfffffff : PCI MMCONFIG 0000 [bus 00-ff]
b0000000-bfffffff : reserved
c0000000-febfffff : PCI Bus 0000:00
f8000000-fbffffff : 0000:00:01.0
[ ... ]
So this is a guest visible change.
Cc: László Érsek <lersek@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190607073429.3436-1-kraxel@redhat.com>
arm and i386 has almost the same function acpi_add_rom_blob(), except
giving different FWCfgCallback function.
This patch moves acpi_add_rom_blob() to utils.c by passing
FWCfgCallback to it.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
v7:
* rebase on top of current master because of conflict
v6:
* change author from Igor to Michael
v5:
* remove unnecessary header glib/gprintf.h
* rearrange include header to make it more suitable
v4:
* extract -> moves
* adjust comment in source to make checkpatch happy
v3:
* put acpi_add_rom_blob() to hw/acpi/utils.c
v2:
* remove unused header in original source file
Message-Id: <20190610011830.28398-1-richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
Other accelerators have their own headers: sysemu/hax.h, sysemu/hvf.h,
sysemu/kvm.h, sysemu/whpx.h. Only tcg_enabled() & friends sit in
qemu-common.h. This necessitates inclusion of qemu-common.h into
headers, which is against the rules spelled out in qemu-common.h's
file comment.
Move tcg_enabled() & friends into their own header sysemu/tcg.h, and
adjust #include directives.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-2-armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[Rebased with conflicts resolved automatically, except for
accel/tcg/tcg-all.c]
Cleanup in the boilerplate that each target must define.
Replace x86_env_get_cpu with env_archcpu. The combination
CPU(x86_env_get_cpu) should have used ENV_GET_CPU to begin;
use env_cpu now.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
stricter rules for acpi tables: we now fail
on any difference that isn't whitelisted.
vhost-scsi migration.
some cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJc+B4YAAoJECgfDbjSjVRpq1EIAJR7tCxcpu9GggVlinmUA8G4
tmSAe06IryH7+nF3RsnINuGu7ius9qC2/E2y0uJUHhTqiU/RWOfWZ7PPM0EcYZaA
TLPaCe2NUF6/8afeqmvE9Usk7VspI5TDZRms+bonmZz2xP1lHIMN0qW4s7HHLWr8
sZKDtCJ+9cYII93VQwtlR0qiHgv5f0kzcuZeJaZHsAHH6XZGqRuQjI6txcFa4o53
lkdLCEwTnRuwu2wyL84eL5p+E8SzOgR/x1QI+nffrJfsvnmiT7lnOrkjnQlWAp5G
xqwqsUrUxUCuQ+zitwJqmv+H6nx79MwAM7fTHAETCWX703N5o9tZxAnHHqLoa8I=
=cQNg
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, pci, pc: cleanups, features
stricter rules for acpi tables: we now fail
on any difference that isn't whitelisted.
vhost-scsi migration.
some cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 05 Jun 2019 20:55:04 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
bios-tables-test: ignore identical binaries
tests: acpi: add simple arm/virt testcase
tests: add expected ACPI tables for arm/virt board
bios-tables-test: list all tables that differ
vhost-scsi: Allow user to enable migration
vhost-scsi: Add VMState descriptor
vhost-scsi: The vhost backend should be stopped when the VM is not running
bios-tables-test: add diff allowed list
vhost: fix memory leak in vhost_user_scsi_realize
vhost: fix incorrect print type
vhost: remove the dead code
docs: smbios: remove family=x from type2 entry description
pci: Fold pci_get_bus_devfn() into its sole caller
pci: Make is_bridge a bool
pcie: Simplify pci_adjust_config_limit()
acpi: pci: use build_append_foo() API to construct MCFG
hw/acpi: Consolidate build_mcfg to pci.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit b2fc91db84 ("q35: set split kernel irqchip as default") changed
the default for the pc-q35-4.0 machine type to use split irqchip, which
turned out to have disasterous effects on vfio-pci INTx support. KVM
resampling irqfds are registered for handling these interrupts, but
these are non-functional in split irqchip mode. We can't simply test
for split irqchip in QEMU as userspace handling of this interrupt is a
significant performance regression versus KVM handling (GeForce GPUs
assigned to Windows VMs are non-functional without forcing MSI mode or
re-enabling kernel irqchip).
The resolution is to revert the change in default irqchip mode in the
pc-q35-4.1 machine and create a pc-q35-4.0.1 machine for the 4.0-stable
branch. The qemu-q35-4.0 machine type should not be used in vfio-pci
configurations for devices requiring legacy INTx support without
explicitly modifying the VM configuration to use kernel irqchip.
Link: https://bugs.launchpad.net/qemu/+bug/1826422
Fixes: b2fc91db84 ("q35: set split kernel irqchip as default")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <155786484688.13873.6037015630912983760.stgit@gimli.home>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now we have two identical build_mcfg functions.
Consolidate them in acpi/pci.c.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
v4:
* ACPI_PCI depends on both ACPI and PCI
* rebase on latest master, adjust arm Kconfig
v3:
* adjust changelog based on Igor's suggestion
Message-Id: <20190521062836.6541-2-richardw.yang@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Implement fw_cfg_arch_key_name(), which returns the name of a
i386-specific key.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190422195020.1494-5-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
To build MCFG, two information is necessary:
* bus number
* base address
Abstract these two information to AcpiMcfgInfo so that build_mcfg and
build_mcfg_q35 will have the same declaration.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190419003053.8260-5-richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This is obvious the member in AcpiMcfgInfo describe MCFG's property.
Remove the mcfg_ prefix.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190419003053.8260-4-richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Dummy table (with signature "QEMU") creation came from original SeaBIOS
codebase. And QEMU would have to keep it around if there were Q35 machine
that depended on keeping ACPI tables blob constant size. Luckily there
were no versioned Q35 machine types before commit:
(since 2.3) a1666142db acpi-build: make ROMs RAM blocks resizeable
which obsoleted need to keep ACPI tables blob the same size on source/destination.
Considering the 1st versioned machine is pc-q35-2.4, the dummy table
is not really necessary and it's safe to drop it without breaking
cross version migration in both directions unconditionally.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1554822037-329838-1-git-send-email-imammedo@redhat.com>
Reviewed-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 72c194f7e7 added a non-null check on the 'obj' pointer.
Later, commit 500b11ea50 added code which uses the 'obj'
pointer _before_ the assertion check. Move the assertion
_before_ the pointer use.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190427144025.22880-4-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When building with CONFIG_Q35=n, we get:
LINK x86_64-softmmu/qemu-system-x86_64
/usr/bin/ld: hw/i386/acpi-build.o: in function `acpi_get_misc_info':
/source/qemu/hw/i386/acpi-build.c:243: undefined reference to `ich9_lpc_find'
collect2: error: ld returned 1 exit status
make[1]: *** [Makefile:204: qemu-system-x86_64] Error 1
This is due to a dependency in acpi-build.c on the ICH9_LPC
(via ich9_lpc_find) and PIIX4_PM (via piix4_pm_find) devices.
To allow better modularity (compile acpi-build.c with only
Q35/ICH9 or ISAPC/PIIX4), refactor the similar helper as
object_resolve_type_unambiguous(). This way we relax the
linker dependencies and can build the x86 targets with a
selection of machines (instead of all of them).
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190427144025.22880-3-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABAgAGBQJc2SifAAoJEC7Z13T+cC21vyAQAJe3IrtArFD+3lNB30BfVYP0
PT7J//C4wH/E+nAZ7bx6K/MMkutNJyMJArpYGqHk+KGm9oJvVfm9fOZKjUF0rJVo
/WiXH96Ux8eBI0fFUv+ZLCXGWwALIC0N3LeoHbxuwhUBfKd6vv+trddksx/RQjvo
dWA5aVwQAYm106Bj/Q6loeXyIVeWkrRxwCEcnAygCLGHFSsXJ9gj2js8OHCywLVo
kV5KIdaLUw20xh9u6mfNS79Jhe7kHz58GIAMg7VwPZqmiTZJSOMb1uZ6eXk+cGBb
3I2VE7RfEprd+9tE9aEiu1s7mCsW/Kh9NeWQBjiGwTwsja7ewMy08ugqzFFTtyE+
M1kf/8D/xyhRnyeNQUR+2BlcDKeTxmaK1Ndk4ybu9QnRcye4ieZLLGDMqKZdiT9U
vwcilGd0QoxmLXXGTNTcW3sRFl2HDg/h8kaH+9dFZSSMb/T4TaoGebpAT013pSou
t6EWn5QhLu90ptbv57N/4YMRmjg6kvCytl5XMenEoY4cx0bFXkQE8lFv4WTCB9Sv
wv5QXA6VbmcIdHfnIFkhxU5kUonLWWiFPdCcbLmqG74OCssr17fq9+BDxC4umMxb
UTnpxegTX4JcpIup1rvV8vN5J/EBbtrhl+qzCwf+ErK+S34xRqXC80ZWxi0JBleV
BJLdKdD6oJk+xMznju2/
=wO8o
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/huth-gitlab/tags/pull-request-2019-05-13' into staging
Kconfig settings for the Arm machines
# gpg: Signature made Mon 13 May 2019 09:19:43 BST
# gpg: using RSA key 2ED9D774FE702DB5
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/huth-gitlab/tags/pull-request-2019-05-13: (29 commits)
hw/arm: Remove hard-enablement of the remaining PCI devices
hw/arm: Express dependencies of the musca machines with Kconfig
hw/arm: Express dependencies of the xlnx-versal-virt machine with Kconfig
hw/arm: Express dependencies of the ZynqMP zcu102 machine with Kconfig
hw/arm: Express dependencies of the microbit / nrf51 machine with Kconfig
hw/arm: Express dependencies of the remaining IMX boards with Kconfig
hw/arm: Express dependencies of the MSF2 / EMCRAFT_SF2 machine with Kconfig
hw/arm: Express dependencies of sabrelite with Kconfig
hw/arm: Express dependencies of canon-a1100 with Kconfig
hw/arm: Express dependencies of the raspi machines with Kconfig
hw/arm: Express dependencies of the MPS2 boards with Kconfig
hw/arm: Express dependencies of allwinner / cubieboard with Kconfig
hw/arm: Express dependencies of netduino / stm32f2xx with Kconfig
hw/arm: Express dependencies of the virt machine with Kconfig
hw/arm: Express dependencies of the aspeed boards with Kconfig
hw/arm: Express dependencies of collie with Kconfig
hw/arm: Express dependencies of xilinx-zynq with Kconfig
hw/arm: Express dependencies of the PXA2xx machines with Kconfig
hw/arm: Express dependencies of realview, versatile and vexpress with Kconfig
hw/arm: Express dependencies of stellaris with Kconfig
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some of our machines (like the ARM cubieboard) use CONFIG_AHCI for an AHCI
sysbus device, but do not use CONFIG_PCI since they do not feature a PCI
bus. With CONFIG_AHCI but without CONFIG_PCI, currently linking fails:
../hw/ide/ich.o: In function `pci_ich9_ahci_realize':
hw/ide/ich.c:124: undefined reference to `pci_allocate_irq'
hw/ide/ich.c:126: undefined reference to `pci_register_bar'
hw/ide/ich.c:128: undefined reference to `pci_register_bar'
hw/ide/ich.c:131: undefined reference to `pci_add_capability'
hw/ide/ich.c:147: undefined reference to `msi_init'
../hw/ide/ich.o: In function `pci_ich9_uninit':
hw/ide/ich.c:158: undefined reference to `msi_uninit'
../hw/ide/ich.o:(.data.rel+0x50): undefined reference to `vmstate_pci_device'
We must only compile ich.c if CONFIG_PCI is available, too, so introduce a
new config switch for this device.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Leading underscores are ill-advised because such identifiers are
reserved. Trailing underscores are merely ugly. Strip both.
Our header guards commonly end in _H. Normalize the exceptions.
Done with scripts/clean-header-guards.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-7-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Changes to slirp/ dropped, as we're about to spin it off]
Factored out of pc_system_firmware_init() so the next commit can reuse
it in hw/arm/virt.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190416091348.26075-3-armbru@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The loop does two things: map legacy -drive to properties, and collect
all the backends for use after the loop. The next patch will factor
out the former for reuse in hw/arm/virt.c. To make that easier,
rearrange the loop so it does the first thing first, and the second
thing second.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190416091348.26075-2-armbru@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QEMU currently crashes when you try to hot-plug an "nvdimm" device
on older machine types:
$ qemu-system-x86_64 -monitor stdio -M pc-1.1
QEMU 3.1.92 monitor - type 'help' for more information
(qemu) device_add nvdimm,id=nvdimmn1
qemu-system-x86_64: /home/thuth/devel/qemu/util/error.c:57: error_setv:
Assertion `*errp == ((void *)0)' failed.
Aborted (core dumped)
The call to hotplug_handler_pre_plug() in pc_memory_pre_plug() has been
added recently before the check whether nvdimm is enabled. It should
be done after the check. And while we're at it, also check the errp
after the hotplug_handler_pre_plug(), otherwise errors are silently
ignored here.
Fixes: 9040e6dfa8
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190407092314.11066-1-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VTD_RTADDR_RTT is dropped even by the VT-d spec, so QEMU should
probably do the same thing (after all we never really implemented it).
Since we've had a field for that in the migration stream, to keep
compatibility we need to fill the hole up.
Please refer to VT-d spec 10.4.6.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20190329061422.7926-3-peterx@redhat.com>
Reviewed-by: Liu, Yi L <yi.l.liu@intel.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When introducing the initial support for scalable mode we added a
new field into vmstate however we blindly migrate that field without
notice. That'll break migration no matter forward or backward.
The normal way should be that we use something like
VMSTATE_UINT32_TEST() or subsections for the new vmstate field however
for this case of vt-d we can even make it simpler because we've
already migrated all the registers and it'll be fairly simple that we
re-generate root_scalable field from the register values during post
load of the device.
Fixes: fb43cf739e ("intel_iommu: scalable mode emulation")
Reviewed-by: Yi Sun <yi.y.sun@linux.intel.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20190329061422.7926-2-peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If we try to use the intel-iommu device with vfio-pci devices without
caching mode enabled, we're told:
qemu-system-x86_64: We need to set caching-mode=1 for intel-iommu to enable
device assignment with IOMMU protection.
But to enable caching mode, the option is actually "caching-mode=on".
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <155364147432.16467.15898335025013220939.stgit@gimli.home>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Alex Williamson <<a href="mailto:alex.williamson@redhat.com" target="_blank" rel="noreferrer">alex.williamson@redhat.com</a>><br>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tracked down with cleanup-trace-events.pl. Funnies requiring manual
post-processing:
* block.c and blockdev.c trace points are in block/trace-events.
* hw/block/nvme.c uses the preprocessor to hide its trace point use
from cleanup-trace-events.pl.
* include/hw/xen/xen_common.h trace points are in hw/xen/trace-events.
* net/colo-compare and net/filter-rewriter.c use pseudo trace points
colo_compare_udp_miscompare and colo_filter_rewriter_debug to guard
debug code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20190314180929.27722-5-armbru@redhat.com
Message-Id: <20190314180929.27722-5-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Almost all trace-events point to docs/devel/tracing.txt in a comment
right at the beginning. Touch up the ones that don't.
[Updated with Markus' new commit description wording.
--Stefan]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-2-armbru@redhat.com
Message-Id: <20190314180929.27722-2-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
When virtio-vga was added, the intention was to only support it for
those machines where the firmware does not know about virtio-gpu,
and supported VGA legacy hardware before virtio-{gpu,vga} were
introduced.
The Kconfig switch however enabled virtio-vga for all machines with
a PCI bus, and libvirt then prefers it even on hardware where
virtio-gpu would be preferrable. At least for now, only enable
virtio-vga for PC, hppa and pSeries machines, as was the case
before Kconfig dependencies were introduced.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Previously we have per-device system memory aliases when DMAR is
disabled by the system. It will slow the system down if there are
lots of devices especially when DMAR is disabled, because each of the
aliased system address space will contain O(N) slots, and rendering
such N address spaces will be O(N^2) complexity.
This patch introduces a shared nodmar memory region and for each
device we only create an alias to the shared memory region. With the
aliasing, QEMU memory core API will be able to detect when devices are
sharing the same address space (which is the nodmar address space)
when rendering the FlatViews and the total number of FlatViews can be
dramatically reduced when there are a lot of devices.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20190313094323.18263-1-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This fixes when configuring with CONFIG_PCI_DEVICES=n:
$ qemu-system-x86_64 -M q35
qemu-system-x86_64: Unsupported NIC model: e1000e
$ qemu-system-x86_64 -M pc
qemu-system-x86_64: Unsupported NIC model: e1000
Fixes: 7c28b925b7
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190316200818.8265-4-philmd@redhat.com>
CONFIG_I82374 is not needed for PC machines, since they create
i8257 directly instead.
Reported-by: Miroslav Rezanina <mrezanin@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Or if it's not possible to honor the hinted address an error is returned
instead. This makes it easier to spot the actual failure, instead of
failing later on when the caller of xen_remap_bucket realizes the
mapping has not been created at the requested address.
Also note that at least on FreeBSD using MAP_FIXED will cause mmap to
try harder to honor the passed address.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Igor Druzhinin <igor.druzhinin@cirtix.com>
Message-Id: <20190318173731.14494-1-roger.pau@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
For the downstream distribution of QEMU, we want to compile without
CONFIG_PARALLEL. Commit 9157eee1b1 already moved the function
parallel_hds_isa_init() (which is still required for linking) into a file
that is included anyway, but commit bb3d5ea858 moved it
to a separate file which is only compiled again if CONFIG_PARALLEL is
set. To be able to link QEMU again without CONFIG_PARALLEL, the file
should be considered for linking for all targets that have CONFIG_ISA_BUS.
And while we're at it, add a proper comment in there with the rationale
for the separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1552297854-25847-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently we do device realization like below:
hotplug_handler_pre_plug()
dc->realize()
hotplug_handler_plug()
Before we do device realization and plug, we should allocate necessary
resources and check if memory-hotplug-support property is enabled.
At the piix4 and ich9, the memory-hotplug-support property is checked at
plug stage. This means that device has been realized and mapped into guest
address space 'pc_dimm_plug()' by the time acpi plug handler is called,
where it might fail and crash QEMU due to reaching g_assert_not_reached()
(piix4) or error_abort (ich9).
Fix it by checking if memory hotplug is enabled at pre_plug stage
where we can gracefully abort hotplug request.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
CC: Igor Mammedov <imammedo@redhat.com>
CC: Eric Blake <eblake@redhat.com>
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190301033548.6691-1-richardw.yang@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds an option to provide flexibility for user to expose
Scalable Mode to guest. User could expose Scalable Mode to guest by
the config as below:
"-device intel-iommu,caching-mode=on,scalable-mode=on"
The Linux iommu driver has supported scalable mode. Please refer below
patch set:
https://www.spinics.net/lists/kernel/msg2985279.html
Signed-off-by: Liu, Yi L <yi.l.liu@intel.com>
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
Message-Id: <1551753295-30167-4-git-send-email-yi.y.sun@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Per Intel(R) VT-d 3.0, the qi_desc is 256 bits in Scalable
Mode. This patch adds emulation of 256bits qi_desc.
Signed-off-by: Liu, Yi L <yi.l.liu@intel.com>
[Yi Sun is co-developer to rebase and refine the patch.]
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <1551753295-30167-3-git-send-email-yi.y.sun@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Intel(R) VT-d 3.0 spec introduces scalable mode address translation to
replace extended context mode. This patch extends current emulator to
support Scalable Mode which includes root table, context table and new
pasid table format change. Now intel_iommu emulates both legacy mode
and scalable mode (with legacy-equivalent capability set).
The key points are below:
1. Extend root table operations to support both legacy mode and scalable
mode.
2. Extend context table operations to support both legacy mode and
scalable mode.
3. Add pasid tabled operations to support scalable mode.
Signed-off-by: Liu, Yi L <yi.l.liu@intel.com>
[Yi Sun is co-developer to contribute much to refine the whole commit.]
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
Message-Id: <1551753295-30167-2-git-send-email-yi.y.sun@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
The PC machines put firmware in ROM by default. To get it put into
flash memory (required by OVMF), you have to use -drive
if=pflash,unit=0,... and optionally -drive if=pflash,unit=1,...
Why two -drive? This permits setting up one part of the flash memory
read-only, and the other part read/write. It also makes upgrading
firmware on the host easier. Below the hood, it creates two separate
flash devices, because we were too lazy to improve our flash device
models to support sector protection.
The problem at hand is to do the same with -blockdev somehow, as one
more step towards deprecating -drive.
Mapping -drive if=none,... to -blockdev is a solved problem. With
if=T other than if=none, -drive additionally configures a block device
frontend. For non-onboard devices, that part maps to -device. Also a
solved problem. For onboard devices such as PC flash memory, we have
an unsolved problem.
This is actually an instance of a wider problem: our general device
configuration interface doesn't cover onboard devices. Instead, we have
a zoo of ad hoc interfaces that are much more limited. One of them is
-drive, which we'd rather deprecate, but can't until we have suitable
replacements for all its uses.
Sadly, I can't attack the wider problem today. So back to the narrow
problem.
My first idea was to reduce it to its solved buddy by using pluggable
instead of onboard devices for the flash memory. Workable, but it
requires some extra smarts in firmware descriptors and libvirt. Paolo
had an idea that is simpler for libvirt: keep the devices onboard, and
add machine properties for their block backends.
The implementation is less than straightforward, I'm afraid.
First, block backend properties are *qdev* properties. Machines can't
have those, as they're not devices. I could duplicate these qdev
properties as QOM properties, but I hate that.
More seriously, the properties do not belong to the machine, they
belong to the onboard flash devices. Adding them to the machine would
then require bad magic to somehow transfer them to the flash devices.
Fortunately, QOM provides the means to handle exactly this case: add
alias properties to the machine that forward to the onboard devices'
properties.
Properties need to be created in .instance_init() methods. For PC
machines, that's pc_machine_initfn(). To make alias properties work,
we need to create the onboard flash devices there, too. Requires
several bug fixes, in the previous commits. We also have to realize
the devices. More on that below.
If the user sets pflash0, firmware resides in flash memory.
pc_system_firmware_init() maps and realizes the flash devices.
Else, firmware resides in ROM. The onboard flash devices aren't used
then. pc_system_firmware_init() destroys them unrealized, along with
the alias properties.
The existing code to pick up drives defined with -drive if=pflash is
replaced by code to desugar into the machine properties.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <87ftrtux81.fsf@dusky.pond.sub.org>
pc_system_firmware_init() parameter @isapc_ram_fw is PCMachineState
member pci_enabled negated. The next commit will need more of
PCMachineState. To prepare for that, pass a PCMachineState *, and
drop the now redundant parameter @isapc_ram_fw.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190308131445.17502-11-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
This structure is not used since commit 6dd2a5c98a.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190308131445.17502-10-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Our pflash devices are simplistically modelled has having
"num-blocks" sectors of equal size "sector-length". Real hardware
commonly has sectors of different sizes. How our "sector-length"
property is related to the physical device's multiple sector sizes
is unclear.
Helper functions pflash_cfi01_register() and pflash_cfi02_register()
create a pflash device, set properties including "sector-length" and
"num-blocks", and realize. They take parameters @size, @sector_len
and @nb_blocs.
QOMification left parameter @size unused. Obviously, @size should
match @sector_len and @nb_blocs, i.e. size == sector_len * nb_blocs.
All callers satisfy this.
Remove @nb_blocs and compute it from @size and @sector_len.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-16-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
QOMification left parameter @qdev unused in pflash_cfi01_register()
and pflash_cfi02_register(). All callers pass NULL. Remove.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308094610.21210-15-armbru@redhat.com>
flash.h's incomplete struct pflash_t is completed both in
pflash_cfi01.c and in pflash_cfi02.c. The complete types are
incompatible. This can hide type errors, such as passing a pflash_t
created with pflash_cfi02_register() to pflash_cfi01_get_memory().
Furthermore, POSIX reserves typedef names ending with _t.
Rename the two structs to PFlashCFI01 and PFlashCFI02.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308094610.21210-2-armbru@redhat.com>
Signed-off-by: David Kiarie <davidkiarie4@gmail.com>
Message-Id: <20190304151827.1813-2-davidkiarie4@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Intel Processor Trace required CPUID[0x14] but the cpuid_level
have no change when create a kvm guest with
e.g. "-cpu qemu64,+intel-pt".
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Luwei Kang <luwei.kang@intel.com>
Message-Id: <1548805979-12321-1-git-send-email-luwei.kang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some multiboot images could be in the ELF format. In the current
implementation QEMU fails because we try to load these images
as a PVH image.
In order to fix this issue, we should try multiboot first (we
already check the multiboot magic header before to load it).
If it is not a multiboot image, we can try the PVH loader.
Fixes: ab969087da ("pvh: Boot uncompressed kernel using direct boot ABI", 2019-01-15)
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20190214180216.246707-1-sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As NVDIMM support is looming for ARM and SPAPR, let's
move the acpi_nvdimm_state to the generic machine struct
instead of duplicating the same code in several machines.
It is also renamed into nvdimms_state and becomes a pointer.
nvdimm and nvdimm-persistence become generic machine options.
They become guarded by a nvdimm_supported machine class member.
We also add a description for those options.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190308182053.5487-3-eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
As we intend to migrate the acpi_nvdimm_state into
the base machine with a new dimms_state name, let's
also rename the datatype.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308182053.5487-2-eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
%-softmmu.mak only keep boards definitions in Kconfig mode.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-43-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
remove default-configs/hyperv.mak and make dependencies
with Kconfig.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-41-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-38-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This way, the default-configs file only need to specify the boards
and any optional devices.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-37-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-36-yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The make_device_config.sh script is replaced by minikconf, which
is modified to support the same command line as its predecessor.
The roots of the parsing are default-configs/*.mak, Kconfig.host and
hw/Kconfig. One difference with make_device_config.sh is that all symbols
have to be defined in a Kconfig file, including those coming from the
configure script. This is the reason for the Kconfig.host file introduced
in the previous patch. Whenever a file in default-configs/*.mak used
$(...) to refer to a config-host.mak symbol, this is replaced by a
Kconfig dependency; this part must be done already in this patch
for bisectability.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-28-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When unplugging a device, at one point the device will be destroyed
via object_unparent(). This will, one the one hand, unrealize the
removed device hierarchy, and on the other hand, destroy/free the
device hierarchy.
When chaining hotplug handlers, we want to overwrite a bus hotplug
handler by the machine hotplug handler, to be able to perform
some part of the plug/unplug and to forward the calls to the bus hotplug
handler.
For now, the bus hotplug handler would trigger an object_unparent(), not
allowing us to perform some unplug action on a device after we forwarded
the call to the bus hotplug handler. The device would be gone at that
point.
machine_unplug_handler(dev)
/* eventually do unplug stuff */
bus_unplug_handler(dev)
/* dev is gone, we can't do more unplug stuff */
So move the object_unparent() to the original caller of the unplug. For
now, keep the unrealize() at the original places of the
object_unparent(). For implicitly chained hotplug handlers (e.g. pc
code calling acpi hotplug handlers), the object_unparent() has to be
done by the outermost caller. So when calling hotplug_handler_unplug()
from inside an unplug handler, nothing is to be done.
hotplug_handler_unplug(dev) -> calls machine_unplug_handler()
machine_unplug_handler(dev) {
/* eventually do unplug stuff */
bus_unplug_handler(dev) -> calls unrealize(dev)
/* we can do more unplug stuff but device already unrealized */
}
object_unparent(dev)
In the long run, every unplug action should be factored out of the
unrealize() function into the unplug handler (especially for PCI). Then
we can get rid of the additonal unrealize() calls and object_unparent()
will properly unrealize the device hierarchy after the device has been
unplugged.
hotplug_handler_unplug(dev) -> calls machine_unplug_handler()
machine_unplug_handler(dev) {
/* eventually do unplug stuff */
bus_unplug_handler(dev) -> only unplugs, does not unrealize
/* we can do more unplug stuff */
}
object_unparent(dev) -> will unrealize
The original approach was suggested by Igor Mammedov for the PCI
part, but I extended it to all hotplug handlers. I consider this one
step into the right direction.
To summarize:
- object_unparent() on synchronous unplugs is done by common code
-- "Caller of hotplug_handler_unplug"
- object_unparent() on asynchronous unplugs ("unplug requests") has to
be done manually
-- "Caller of hotplug_handler_unplug"
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190228122849.4296-2-david@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Function pc_acpi_init() is not used anymore.
Remove the definition and declaration.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190214084939.20640-2-richardw.yang@linux.intel.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Migration capability is being added for pm_smbus and SMBus devices.
This change will allow backwards compatibility to be kept when
migrating back to an old qemu version. Add a bool to the machine
class tho keep smbus migration from happening. Future changes
will use this.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
smbus.c and smbus.h had device side code, master side code, and
smbus.h has some smbus_eeprom.c definitions. Split them into
separate files.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The second argument of build_facs() is not used, just remove it.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This patch makes the a TPM 2.0 with TIS interface available under the
HID 'MSF0101'. This is supported by Linux and also Windows now
recognizes the TPM 2.0 with TIS interface. Leave the TPM 1.2 as before.
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
This is found when I was debugging another problem. Until now no bug
is reported with this but we'd better reset the IR status correctly
after a system reset.
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When calculating use_iommu, we wanted to first detect whether DMAR is
enabled, then check whether PT is enabled if DMAR is enabled. However
in the current code we used "&" rather than "&&" so the ordering
requirement is lost (instead it'll be an "AND" operation). This could
introduce errors dumped in QEMU console when rebooting a guest with
both assigned device and vIOMMU, like:
qemu-system-x86_64: vtd_dev_to_context_entry: invalid root entry:
rsvd=0xf000ff53f000e2c3, val=0xf000ff53f000ff53 (reserved nonzero)
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Let's avoid manually looking up the hotplug handler class. Use the
existing wrappers instead.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20181212095707.19358-1-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CONFIG_PIIX and CONFIG_Q35 created for the pc board object files. These
are enabled automatically at default-configs/i386-softmmu.mak and
default-configs/x86_64-softmmu.mak
Signed-off-by: Ákos Kovács <akoskovacs@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-7-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since linux commit: cf8fa920cb42 ("i386: handle an initrd in highmem (version 2)")
linux has supported initrd up to 4 GB, but the header field
ramdisk_max is still set to 2 GB to avoid "possible bootloader bugs".
When use '-kernel vmlinux -initrd initrd.cgz' to launch a VM,
the firmware(it could be linuxboot_dma.bin) helps to read initrd
contents into guest memory(below ramdisk_max) and jump to kernel.
that's similar with what bootloader does, like grub.
In addition, initrd_max is uint32_t simply because QEMU doesn't support
the 64-bit boot protocol (specifically the ext_ramdisk_image field).
Therefore here just limit initrd_max to UINT32_MAX simply as well to
allow initrd to be loaded below 4 GB.
NOTE: it's possible that linux protocol within [0x208, 0x20c]
supports up to 4 GB initrd as well.
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Eduardo Habkost <ehabkost@redhat.com>
CC: "Michael S. Tsirkin" <mst@redhat.com>
CC: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
it's from v4.20-rc5.
CC: Stefano Garzarella <sgarzare@redhat.com>
CC: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to avoid migration issues, we enable PVH only for
machine type >= 4.0
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use pvh.bin option rom when we are booting an uncompressed
kernel using the x86/HVM direct boot ABI.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Based-on: <1547554687-12687-1-git-send-email-liam.merwick@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When initrd is specified, load and expose it to the guest firmware
through fw_cfg. The firmware will fill the hvm_start_info for the
kernel.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Based-on: <1545422632-24444-5-git-send-email-liam.merwick@oracle.com>
Signed-off-by: Liam Merwick <Liam.Merwick@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These changes (along with corresponding Linux kernel and qboot changes)
enable a guest to be booted using the x86/HVM direct boot ABI.
This commit adds a load_elfboot() routine to pass the size and
location of the kernel entry point to qboot (which will fill in
the start_info struct information needed to to boot the guest).
Having loaded the ELF binary, load_linux() will run qboot
which continues the boot.
The address for the kernel entry point is read from an ELF Note
in the uncompressed kernel binary by a helper routine passed
to load_elf().
Co-developed-by: George Kennedy <George.Kennedy@oracle.com>
Signed-off-by: George Kennedy <George.Kennedy@oracle.com>
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds an optional function pointer, 'elf_note_fn', to
load_elf() which causes load_elf() to additionally parse any
ELF program headers of type PT_NOTE and check to see if the ELF
Note is of the type specified by the 'translate_opaque' arg.
If a matching ELF Note is found then the specfied function pointer
is called to process the ELF note.
Passing a NULL function pointer results in ELF Notes being skipped.
The first consumer of this functionality is the PVHboot support
which needs to read the XEN_ELFNOTE_PHYS32_ENTRY ELF Note while
loading the uncompressed kernel binary in order to discover the
boot entry address for the x86/HVM direct boot ABI.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- code clean-up
- LGPL information clean-up
- fix typo (acpi)
-----BEGIN PGP SIGNATURE-----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=1OOM
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/vivier2/tags/trivial-branch-pull-request' into staging
- add device category (edu, i8042, sd memory card)
- code clean-up
- LGPL information clean-up
- fix typo (acpi)
# gpg: Signature made Wed 30 Jan 2019 13:21:50 GMT
# gpg: using RSA key F30C38BD3F2FBE3C
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier2/tags/trivial-branch-pull-request:
virtio-blk: remove duplicate definition of VirtIOBlock *s pointer
hw/block: clean up stale xen_disk trace entries
target/m68k: Fix LGPL information in the file headers
target/s390x: Fix LGPL version in the file header comments
tcg: Fix LGPL version number
target/tricore: Fix LGPL version number
target/openrisc: Fix LGPL version number
COPYING.LIB: Synchronize the LGPL 2.1 with the version from gnu.org
Don't talk about the LGPL if the file is licensed under the GPL
hw: sd: set category of the sd memory card
hw: input: set category of the i8042 device
typo: apci->acpi
hw: edu: set category of the edu device
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
apci_1_compatible should be acpi_1_compatible.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190125094047.22276-1-dgilbert@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Modern AMD CPUs support NPT and NRIPSAVE features and KVM exposes these
when present. NRIPSAVE apeared somewhere in Opteron_G3 lifetime (e.g.
QuadCore AMD Opteron 2378 has is but QuadCore AMD Opteron HE 2344 doesn't),
NPT was introduced a bit earlier.
Add the FEAT_SVM leaf to Opteron_G4/G5 and EPYC/EPYC-IBPB cpu models.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20190121155051.5628-1-vkuznets@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Update the stepping from 5 to 6, in order that
the Cascadelake-Server CPU model can support AVX512VNNI
and MSR based features exposed by ARCH_CAPABILITIES.
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20181227024304.12182-2-tao3.xu@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The TPM Physical Presence interface consists of an ACPI part, a shared
memory part, and code in the firmware. Users can send messages to the
firmware by writing a code into the shared memory through invoking the
ACPI code. When a reboot happens, the firmware looks for the code and
acts on it by sending sequences of commands to the TPM.
This patch adds the ACPI code. It is similar to the one in EDK2 but doesn't
assume that SMIs are necessary to use. It uses a similar datastructure for
the shared memory as EDK2 does so that EDK2 and SeaBIOS could both make use
of it. I extended the shared memory data structure with an array of 256
bytes, one for each code that could be implemented. The array contains
flags describing the individual codes. This decouples the ACPI implementation
from the firmware implementation.
The underlying TCG specification is accessible from the following page.
https://trustedcomputinggroup.org/tcg-physical-presence-interface-specification/
This patch implements version 1.30.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
[ Marc-André - ACPI code improvements and windows fixes ]
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To avoid having to hard code the base address of the PPI virtual
memory device we introduce a fw_cfg file etc/tpm/config that holds the
base address of the PPI device, the version of the PPI interface and
the version of the attached TPM.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
[ Marc-André: renamed to etc/tpm/config, made it static, document it ]
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It's been marked as deprecated in QEMU v2.6.0 already, so really nobody
should use the legacy "ivshmem" device anymore (but use ivshmem-plain or
ivshmem-doorbell instead). Time to remove the deprecated device now.
Belatedly also update a mention of the deprecated "ivshmem" in the file
docs/specs/ivshmem-spec.txt to "ivshmem-doorbell". Missed in commit
5400c02b90 ("ivshmem: Split ivshmem-plain, ivshmem-doorbell off ivshmem").
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* Reenable RDTSCP support on Opteron_G[345] CPU models CPU models
(Borislav Petkov)
* host-phys-bits-limit option for better control of 5-level EPT
(Eduardo Habkost)
* Disable MPX support on named CPU models (Paolo Bonzini)
* expose HV_CPUID_ENLIGHTMENT_INFO.EAX and HV_CPUID_NESTED_FEATURES.EAX
as feature words (Vitaly Kuznetsov)
-----BEGIN PGP SIGNATURE-----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=S08V
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ehabkost/tags/x86-next-pull-request' into staging
x86 queue, 2019-01-14
* Reenable RDTSCP support on Opteron_G[345] CPU models CPU models
(Borislav Petkov)
* host-phys-bits-limit option for better control of 5-level EPT
(Eduardo Habkost)
* Disable MPX support on named CPU models (Paolo Bonzini)
* expose HV_CPUID_ENLIGHTMENT_INFO.EAX and HV_CPUID_NESTED_FEATURES.EAX
as feature words (Vitaly Kuznetsov)
# gpg: Signature made Mon 14 Jan 2019 14:33:55 GMT
# gpg: using RSA key 2807936F984DC5A6
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>"
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/x86-next-pull-request:
i386/kvm: add a comment explaining why .feat_names are commented out for Hyper-V feature bits
x86: host-phys-bits-limit option
target/i386: Disable MPX support on named CPU models
target-i386: Reenable RDTSCP support on Opteron_G[345] CPU models CPU models
i386/kvm: expose HV_CPUID_ENLIGHTMENT_INFO.EAX and HV_CPUID_NESTED_FEATURES.EAX as feature words
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
MPX support is being phased out by Intel; GCC has dropped it, Linux
is also going to do that. Even though KVM will have special code
to support MPX after the kernel proper stops enabling it in XCR0,
we probably also want to deprecate that in a few years. As a start,
do not enable it by default for any named CPU model starting with
the 4.0 machine types; this include Skylake, Icelake and Cascadelake.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20181220121100.21554-1-pbonzini@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The missing functionality was added ~3 years ago with the Linux commit
46896c73c1a4 ("KVM: svm: add support for RDTSCP")
so reenable RDTSCP support on those CPU models.
Opteron_G2 - being family 15, model 6, doesn't have RDTSCP support
(the real hardware doesn't have it. K8 got RDTSCP support with the NPT
models, i.e., models >= 0x40).
Document the host's minimum required kernel version, while at it.
Signed-off-by: Borislav Petkov <bp@suse.de>
Message-ID: <20181212200803.GG6653@zn.tnic>
[ehabkost: moved compat properties code to pc.c]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This patch adds the basic boilerplate for a 'XenBus' object that will act
as a parent to 'XenDevice' PV backends.
A new 'XenBridge' object is also added to connect XenBus to the system bus.
The XenBus object is instantiated by a new xen_bus_init() function called
from the same sites as the legacy xen_be_init() function.
Subsequent patches will flesh-out the functionality of these objects.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
...and xen_backend.h to xen-legacy-backend.h
Rather than attempting to convert the existing backend infrastructure to
be QOM compliant (which would be hard to do in an incremental fashion),
subsequent patches will introduce a completely new framework for Xen PV
backends. Hence it is necessary to re-name parts of existing code to avoid
name clashes. The re-named 'legacy' infrastructure will be removed once all
backends have been ported to the new framework.
This patch is purely cosmetic. No functional change.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
* esp bugfixes (Guenter)
* Windows build cleanup (Marc-André)
* checkpatch logic improvements (Paolo)
* coalesced range bugfix (Paolo)
* switch testsuite to TAP (Paolo)
* QTAILQ rewrite (Paolo)
* block/iscsi.c cancellation fixes (Stefan)
* improve selection of the default accelerator (Thomas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJcOKyMAAoJEL/70l94x66DxKEH/1ho2Xl8ezxCecA6q3HqTgMT
NJ/ntdqQwVwekKOWzsywnM3/LkEDLH55MxbTeQ8M/Vb1seS8eROz24/gPTzvFrfR
n/d11rDV1EJfWe0H7nGLLFiRv0MSjxLpG9c3dlOKWhwOYHm25tr48PsdfVFP9Slz
BK3rwrMeDgArfptHAIsAXt2h1S0EzrG9pMwGDpErCDzziXxBhUESE0Iqfw8LsH1K
VjMn6rn7Ts1XKlxxwsm+BzHlTJghbj3tWPIfk+6uK2isP4iM3gFCoav3SG9XVXof
V9+vFyMxdtZKT/0HvajhUS4/1S/uGBNNchZRnCxXlpbueWc5ROtvarhM6Hb0eck=
=i8E5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* HAX support for Linux hosts (Alejandro)
* esp bugfixes (Guenter)
* Windows build cleanup (Marc-André)
* checkpatch logic improvements (Paolo)
* coalesced range bugfix (Paolo)
* switch testsuite to TAP (Paolo)
* QTAILQ rewrite (Paolo)
* block/iscsi.c cancellation fixes (Stefan)
* improve selection of the default accelerator (Thomas)
# gpg: Signature made Fri 11 Jan 2019 14:47:40 GMT
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (34 commits)
avoid TABs in files that only contain a few
remove space-tab sequences
scripts: add script to convert multiline comments into 4-line format
hw/watchdog/wdt_i6300esb: remove a unnecessary comment
checkpatch: warn about qemu/queue.h head structs that are not typedef-ed
qemu/queue.h: simplify reverse access to QTAILQ
qemu/queue.h: reimplement QTAILQ without pointer-to-pointers
qemu/queue.h: remove Q_TAILQ_{HEAD,ENTRY}
qemu/queue.h: typedef QTAILQ heads
qemu/queue.h: leave head structs anonymous unless necessary
vfio: make vfio_address_spaces static
qemu/queue.h: do not access tqe_prev directly
test: replace gtester with a TAP driver
test: execute g_test_run when tests are skipped
qga: drop < Vista compatibility
build-sys: build with Vista API by default
build-sys: move windows defines in osdep.h header
build-sys: don't include windows.h, osdep.h does it
scsi: esp: Defer command completion until previous interrupts have been handled
esp-pci: Fix status register write erase control
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Most files that have TABs only contain a handful of them. Change
them to spaces so that we don't confuse people.
disas, standard-headers, linux-headers and libdecnumber are imported
from other projects and probably should be exempted from the check.
Outside those, after this patch the following files still contain both
8-space and TAB sequences at the beginning of the line. Many of them
have a majority of TABs, or were initially committed with all tabs.
bsd-user/i386/target_syscall.h
bsd-user/x86_64/target_syscall.h
crypto/aes.c
hw/audio/fmopl.c
hw/audio/fmopl.h
hw/block/tc58128.c
hw/display/cirrus_vga.c
hw/display/xenfb.c
hw/dma/etraxfs_dma.c
hw/intc/sh_intc.c
hw/misc/mst_fpga.c
hw/net/pcnet.c
hw/sh4/sh7750.c
hw/timer/m48t59.c
hw/timer/sh_timer.c
include/crypto/aes.h
include/disas/bfd.h
include/hw/sh4/sh.h
libdecnumber/decNumber.c
linux-headers/asm-generic/unistd.h
linux-headers/linux/kvm.h
linux-user/alpha/target_syscall.h
linux-user/arm/nwfpe/double_cpdo.c
linux-user/arm/nwfpe/fpa11_cpdt.c
linux-user/arm/nwfpe/fpa11_cprt.c
linux-user/arm/nwfpe/fpa11.h
linux-user/flat.h
linux-user/flatload.c
linux-user/i386/target_syscall.h
linux-user/ppc/target_syscall.h
linux-user/sparc/target_syscall.h
linux-user/syscall.c
linux-user/syscall_defs.h
linux-user/x86_64/target_syscall.h
slirp/cksum.c
slirp/if.c
slirp/ip.h
slirp/ip_icmp.c
slirp/ip_icmp.h
slirp/ip_input.c
slirp/ip_output.c
slirp/mbuf.c
slirp/misc.c
slirp/sbuf.c
slirp/socket.c
slirp/socket.h
slirp/tcp_input.c
slirp/tcpip.h
slirp/tcp_output.c
slirp/tcp_subr.c
slirp/tcp_timer.c
slirp/tftp.c
slirp/udp.c
slirp/udp.h
target/cris/cpu.h
target/cris/mmu.c
target/cris/op_helper.c
target/sh4/helper.c
target/sh4/op_helper.c
target/sh4/translate.c
tcg/sparc/tcg-target.inc.c
tests/tcg/cris/check_addo.c
tests/tcg/cris/check_moveq.c
tests/tcg/cris/check_swap.c
tests/tcg/multiarch/test-mmap.c
ui/vnc-enc-hextile-template.h
ui/vnc-enc-zywrle.h
util/envlist.c
util/readline.c
The following have only TABs:
bsd-user/i386/target_signal.h
bsd-user/sparc64/target_signal.h
bsd-user/sparc64/target_syscall.h
bsd-user/sparc/target_signal.h
bsd-user/sparc/target_syscall.h
bsd-user/x86_64/target_signal.h
crypto/desrfb.c
hw/audio/intel-hda-defs.h
hw/core/uboot_image.h
hw/sh4/sh7750_regnames.c
hw/sh4/sh7750_regs.h
include/hw/cris/etraxfs_dma.h
linux-user/alpha/termbits.h
linux-user/arm/nwfpe/fpopcode.h
linux-user/arm/nwfpe/fpsr.h
linux-user/arm/syscall_nr.h
linux-user/arm/target_signal.h
linux-user/cris/target_signal.h
linux-user/i386/target_signal.h
linux-user/linux_loop.h
linux-user/m68k/target_signal.h
linux-user/microblaze/target_signal.h
linux-user/mips64/target_signal.h
linux-user/mips/target_signal.h
linux-user/mips/target_syscall.h
linux-user/mips/termbits.h
linux-user/ppc/target_signal.h
linux-user/sh4/target_signal.h
linux-user/sh4/termbits.h
linux-user/sparc64/target_syscall.h
linux-user/sparc/target_signal.h
linux-user/x86_64/target_signal.h
linux-user/x86_64/termbits.h
pc-bios/optionrom/optionrom.h
slirp/mbuf.h
slirp/misc.h
slirp/sbuf.h
slirp/tcp.h
slirp/tcp_timer.h
slirp/tcp_var.h
target/i386/svm.h
target/sparc/asi.h
target/xtensa/core-dc232b/xtensa-modules.inc.c
target/xtensa/core-dc233c/xtensa-modules.inc.c
target/xtensa/core-de212/core-isa.h
target/xtensa/core-de212/xtensa-modules.inc.c
target/xtensa/core-fsf/xtensa-modules.inc.c
target/xtensa/core-sample_controller/core-isa.h
target/xtensa/core-sample_controller/xtensa-modules.inc.c
target/xtensa/core-test_kc705_be/core-isa.h
target/xtensa/core-test_kc705_be/xtensa-modules.inc.c
tests/tcg/cris/check_abs.c
tests/tcg/cris/check_addc.c
tests/tcg/cris/check_addcm.c
tests/tcg/cris/check_addoq.c
tests/tcg/cris/check_bound.c
tests/tcg/cris/check_ftag.c
tests/tcg/cris/check_int64.c
tests/tcg/cris/check_lz.c
tests/tcg/cris/check_openpf5.c
tests/tcg/cris/check_sigalrm.c
tests/tcg/cris/crisutils.h
tests/tcg/cris/sys.c
tests/tcg/i386/test-i386-ssse3.c
ui/vgafont.h
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20181213223737.11793-3-pbonzini@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Eric Blake <eblake@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Stefan Markovic <smarkovic@wavecomp.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Most list head structs need not be given a name. In most cases the
name is given just in case one is going to use QTAILQ_LAST, QTAILQ_PREV
or reverse iteration, but this does not apply to lists of other kinds,
and even for QTAILQ in practice this is only rarely needed. In addition,
we will soon reimplement those macros completely so that they do not
need a name for the head struct. So clean up everything, not giving a
name except in the rare case where it is necessary.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of verbose arrays with 4 lines for each entry, make each
entry take only one line. This makes long arrays that couldn't
fit in the screen become short and readable.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190107193020.21744-4-ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
stringify() is useful when we need to use macros in compat_props
(like when we set virtio-baloon-pci.class=PCI_CLASS_MEMORY_RAM at
pc_i440fx_1_0_machine_options()), but it is pointless when we are
already providing a number literal.
Replace stringify() with string literals when appropriate.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190107193020.21744-3-ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make them more QOMConventional.
Cc:qemu-trivial@nongnu.org
Signed-off-by: Li Qiang <liq3ea@163.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20190105023831.66910-1-liq3ea@163.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This function is only needed when Q35 is in use. Moving it to
the same file that uses it lets you disable the entire USB
subsystem in x86_64-softmmu.mak; of course doing that will
cause -usb to break horribly, but one thing at a time.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1545064358-4601-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_1() function with pc_compat_2_1_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_1() function with pc_compat_2_1_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_2() function with pc_compat_2_2_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_3() function with pc_compat_2_3_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Similarly to accel properties, move compat properties out of globals
registration, and apply the machine compat properties during
device_post_init().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
When the user didn't specify "intremap" for the IOMMU device, we turn
it on by default if it is supported. This will turn IR on for the
default Q35 platform as long as the IOMMU device is specified on new
kernels.
Signed-off-by: Peter Xu <peterx@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Switch the intr_supported variable from a boolean to OnOffAuto type so
that we can know whether the user specified it or not. With that
we'll have a chance to help the user to choose more wisely where
possible. Introduce x86_iommu_ir_supported() to mask these changes.
No functional change at all.
Signed-off-by: Peter Xu <peterx@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Starting from QEMU 4.0, let's specify "split" as the default value for
kernel-irqchip.
So for QEMU>=4.0 we'll have: allowed=Y,required=N,split=Y
for QEMU<=3.1 we'll have: allowed=Y,required=N,split=N
(omitting all the "kernel_irqchip_" prefix)
Note that this will let the default q35 machine type to depend on
Linux version 4.4 or newer because that's where split irqchip is
introduced in kernel. But it's fine since we're boosting supported
Linux version for QEMU 4.0 to around Linux 4.5. For more information
please refer to the discussion on AMD's RDTSCP:
https://lore.kernel.org/lkml/20181210181328.GA762@zn.tnic/
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
They've been deprecated for two releases and nobody complained that they
are still required anymore, so it's time to remove these now.
And while we're at it, mark the other remaining old 0.x machine types
as deprecated (since they can not properly be used for live-migration
anyway).
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Now that build_rsdp() supports building both legacy and current RSDP
tables, we can move it to a generic folder (hw/acpi) and have the i386
ACPI code reuse it in order to reduce code duplication.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
AcpiRsdpDescriptor describes revision 2 RSDP table so using sizeof(*rsdp)
for checksum calculation isn't correct since we are adding extra 16 bytes.
But acpi_data_push() zeroes out table, so just by luck we are summing up
exta zeros which still yelds correct checksum.
Fix it up by explicitly stating table size instead of using
pointer arithmetics on stucture.
PS:
Extra 16 bytes are still wasted, but droping them will break migration
for machines older than 2.3 due to size mismatch, for 2.3 and older it's
not an issue since they are using resizable memory regions (a1666142d)
for ACPI blobs. So keep wasting memory to avoid breaking old machines.
Fixes: 72c194f7e (i386: ACPI table generation code from seabios)
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For both x86 and ARM architectures, the internal RSDP build API can
return void as the current return value is unused.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We're going to have 57bits aw-bits support sooner. It's possibly time
to remove the "x-" prefix.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Support DMA read/write draining should be easy for existing VT-d
emulation since the emulation itself does not have any request queue
there so we don't need to do anything to flush the un-commited queue.
What we need to do is to declare the support.
These capabilities are required to pass Windows SVVP test program. It
is verified that when with parameters "x-aw-bits=48,caching-mode=off"
we can pass the Windows SVVP test with this patch applied. Otherwise
we'll fail with:
IOMMU[0] - DWD (DMA write draining) not supported
IOMMU[0] - DWD (DMA read draining) not supported
Segment 0 has no DMA remapping capable IOMMU units
However since these bits are not declared support for QEMU<=3.1, we'll
need a compatibility bit for it and we turn this on by default only
for QEMU>=4.0.
Please refer to VT-d spec 6.5.4 for more information.
CC: Yu Wang <wyu@redhat.com>
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1654550
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Report more *_invalid() tracepoints to error_report_once() so that we
can detect issues even without tracing enabled. Drop those tracepoints.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The iotlb.iova can be zero if failure really happened. Dump the addr
instead.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
SMBIOS is just another firmware interface used by some QEMU models.
We will later introduce more firmware interfaces in this subdirectory.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When issuing the qmp/hmp 'system_wakeup' command, what happens in a
nutshell is:
- qmp_system_wakeup_request set runstate to RUNNING, sets a wakeup_reason
and notify the event
- in the main_loop, all vcpus are paused, a system reset is issued, all
subscribers of wakeup_notifiers receives a notification, vcpus are then
resumed and the wake up QAPI event is fired
Note that this procedure alone doesn't ensure that the guest will awake
from SUSPENDED state - the subscribers of the wake up event must take
action to resume the guest, otherwise the guest will simply reboot. At
this moment, only the ACPI machines via acpi_pm1_cnt_init and xen_hvm_init
have wake-up from suspend support.
However, only the presence of 'system_wakeup' is required for QGA to
support 'guest-suspend-ram' and 'guest-suspend-hybrid' at this moment.
This means that the user/management will expect to suspend the guest using
one of those suspend commands and then resume execution using system_wakeup,
regardless of the support offered in system_wakeup in the first place.
This patch creates a new API called query-current-machine [1], that holds
a new flag called 'wakeup-suspend-support' that indicates if the guest
supports wake up from suspend via system_wakeup. The machine is considered
to implement wake-up support if a call to a new 'qemu_register_wakeup_support'
is made during its init, as it is now being done inside acpi_pm1_cnt_init
and xen_hvm_init. This allows for any other machine type to declare wake-up
support regardless of ACPI state or wakeup_notifiers subscription, making easier
for newer implementations that might have their own mechanisms in the future.
This is the expected output of query-current-machine when running a x86
guest:
{"execute" : "query-current-machine"}
{"return": {"wakeup-suspend-support": true}}
Running the same x86 guest, but with the --no-acpi option:
{"execute" : "query-current-machine"}
{"return": {"wakeup-suspend-support": false}}
This is the output when running a pseries guest:
{"execute" : "query-current-machine"}
{"return": {"wakeup-suspend-support": false}}
With this extra tool, management can avoid situations where a guest
that does not have proper suspend/wake capabilities ends up in
inconsistent state (e.g.
https://github.com/open-power-host-os/qemu/issues/31).
[1] the decision of creating the query-current-machine API is based
on discussions in the QEMU mailing list where it was decided that
query-target wasn't a proper place to store the wake-up flag, neither
was query-machines because this isn't a static property of the
machine object. This new API can then be used to store other
dynamic machine properties that are scattered around the code
ATM. More info at:
https://lists.gnu.org/archive/html/qemu-devel/2018-05/msg04235.html
Reported-by: Balamuruhan S <bala24@linux.vnet.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20181205194701.17836-2-danielhb413@gmail.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The load_image() function is deprecated, as it does not let the
caller specify how large the buffer to read the file into is.
Instead use load_image_size().
While we are converting the code, add the missing error check.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20181130151712.2312-7-peter.maydell@linaro.org
The load_image() function is deprecated, as it does not let the
caller specify how large the buffer to read the file into is.
Use the glib g_file_get_contents() function instead, which does
the whole "allocate memory for the file and read it in" operation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20181130151712.2312-6-peter.maydell@linaro.org
Instead of setting suppress_vmdesc at instance_init time, set
default_machine_opts on pc_i440fx_2_2_machine_options() to
implement equivalent behavior.
This will let us eliminate the need for pc_compat_*() functions
for PC machine-types.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20181205205827.19387-6-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Including all machine types that might have a pcie-root-port.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <154394083644.28192.8501647946108201466.stgit@gimli.home>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
[ehabkost: fixed accidental recursion at spapr_machine_3_1_class_options()]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This makes their function more clear and prevents conflicts when adding
the actual devices to the machine state, if necessary.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20181107152434.22219-1-minyard@acm.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We have a couple of PC_COMPAT_3_0, so we should have 3.1 PC machines,
and update the 3.0 machines to make use of those.
Fixes a "Known issue" from https://wiki.qemu.org/Planning/3.1.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20181120132604.22854-1-marcandre.lureau@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Now that amd-iommu support interrupt remapping, enable the GASup in IVRS
table and GASup in extended feature register to indicate that IOMMU
support guest virtual APIC mode. GASup provides option to guest OS to
make use of 128-bit IRTE.
Note that the GAMSup is set to zero to indicate that amd-iommu does not
support guest virtual APIC mode (aka AVIC) which would be used for the
nested VMs.
See Table 21 from IOMMU spec for interrupt virtualization controls
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Tom Lendacky <Thomas.Lendacky@amd.com>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Emulate the interrupt remapping support when guest virtual APIC is
enabled.
For more information refer: IOMMU spec rev 3.0 (section 2.2.5.2)
When VAPIC is enabled, it uses interrupt remapping as defined in
Table 22 and Figure 17 from IOMMU spec.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Tom Lendacky <Thomas.Lendacky@amd.com>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When interrupt remapping is enabled, add a special IVHD device
(type IOAPIC).
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Tom Lendacky <Thomas.Lendacky@amd.com>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Emulate the interrupt remapping support when guest virtual APIC is
not enabled.
For more info Refer: AMD IOMMU spec Rev 3.0 - section 2.2.5.1
When VAPIC is not enabled, it uses interrupt remapping as defined in
Table 20 and Figure 15 from IOMMU spec.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Tom Lendacky <Thomas.Lendacky@amd.com>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Register the interrupt remapping callback and read/write ops for the
amd-iommu-ir memory region.
amd-iommu-ir is set to higher priority to ensure that this region won't
be masked out by other memory regions.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Tom Lendacky <Thomas.Lendacky@amd.com>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To be consistent with intel-iommu:
- rename the address space to use '_' instead of '-'
- update the memory region relationships
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Tom Lendacky <Thomas.Lendacky@amd.com>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently, the amdvi_validate_dte() assumes that a valid DTE will
always have V=1. This is not true. The V=1 means that bit[127:1] are
valid. A valid DTE can have IV=1 and V=0 (i.e address translation
disabled and interrupt remapping enabled)
Remove the V=1 check from amdvi_validate_dte(), make the caller
responsible to check for V or IV bits.
This also fixes a bug in existing code that when error is
detected during the translation we'll fail the translation
instead of assuming a passthrough mode.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Tom Lendacky <Thomas.Lendacky@amd.com>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The vtd_generate_msi_message() in intel-iommu is used to construct a MSI
Message from IRQ. A similar function will be needed when we add interrupt
remapping support in amd-iommu. Moving the function in common file to
avoid the code duplication. Rename it to x86_iommu_irq_to_msi_message().
There is no logic changes in the code flow.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Suggested-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Tom Lendacky <Thomas.Lendacky@amd.com>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Interrupt remapping needs kernel-irqchip={off|split} on both Intel and AMD
platforms. Move the check in common place.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Tom Lendacky <Thomas.Lendacky@amd.com>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We should handle VTD_FR_CONTEXT_ENTRY_P properly when synchronizing
shadow page tables. Having invalid context entry there is perfectly
valid when we move a device out of an existing domain. When that
happens, instead of posting an error we invalidate the whole region.
Without this patch, QEMU will crash if we do these steps:
(1) start QEMU with VT-d IOMMU and two 10G NICs (ixgbe)
(2) bind the NICs with vfio-pci in the guest
(3) start testpmd with the NICs applied
(4) stop testpmd
(5) rebind the NIC back to ixgbe kernel driver
The patch should fix it.
Reported-by: Pei Zhang <pezhang@redhat.com>
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1627272
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There are two callers for vtd_sync_shadow_page_table_range(): one
provided a valid context entry and one not. Move that fetching
operation into the caller vtd_sync_shadow_page_table() where we need to
fetch the context entry.
Meanwhile, remove the error_report_once() directly since we're already
tracing all the error cases in the previous call. Instead, return error
number back to caller. This will not change anything functional since
callers are dropping it after all.
We do this move majorly because we want to do something more later in
vtd_sync_shadow_page_table().
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
QEMU is not handling the global DMAR switch well, especially when from
"on" to "off".
Let's first take the example of system reset.
Assuming that a guest has IOMMU enabled. When it reboots, we will drop
all the existing DMAR mappings to handle the system reset, however we'll
still keep the existing memory layouts which has the IOMMU memory region
enabled. So after the reboot and before the kernel reloads again, there
will be no mapping at all for the host device. That's problematic since
any software (for example, SeaBIOS) that runs earlier than the kernel
after the reboot will assume the IOMMU is disabled, so any DMA from the
software will fail.
For example, a guest that boots on an assigned NVMe device might fail to
find the boot device after a system reboot/reset and we'll be able to
observe SeaBIOS errors if we capture the debugging log:
WARNING - Timeout at nvme_wait:144!
Meanwhile, we should see DMAR errors on the host of that NVMe device.
It's the DMA fault that caused a NVMe driver timeout.
The correct fix should be that we do proper switching of device DMA
address spaces when system resets, which will setup correct memory
regions and notify the backend of the devices. This might not affect
much on non-assigned devices since QEMU VT-d emulation will assume a
default passthrough mapping if DMAR is not enabled in the GCMD
register (please refer to vtd_iommu_translate). However that's required
for an assigned devices, since that'll rebuild the correct GPA to HPA
mapping that is needed for any DMA operation during guest bootstrap.
Besides the system reset, we have some other places that might change
the global DMAR status and we'd better do the same thing there. For
example, when we change the state of GCMD register, or the DMAR root
pointer. Do the same refresh for all these places. For these two
places we'll also need to explicitly invalidate the context entry cache
and iotlb cache.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1625173
CC: QEMU Stable <qemu-stable@nongnu.org>
Reported-by: Cong Li <coli@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
--
v2:
- do the same for GCMD write, or root pointer update [Alex]
- test is carried out by me this time, by observing the
vtd_switch_address_space tracepoint after system reboot
v3:
- rewrite commit message as suggested by Alex
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Provide the function and use it in vtd_init(). Used to reset both
context entry cache and iotlb cache for the whole IOMMU unit.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We're plugging/unplugging a PCDIMMDevice, so directly pass this type
instead of a more generic DeviceState.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20181005092024.14344-5-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
According to KVM API Documentation, we should only
run vcpu ioctls from the same thread that was used
to create the vcpu. This patch makes KVM_KVMCLOCK_CTRL
ioctl consistent with the Documentation.
No functional change.
Signed-off-by: Yongji Xie <xieyongji@baidu.com>
Signed-off-by: Chai Wen <chaiwen@baidu.com>
Message-Id: <1531315364-2551-1-git-send-email-xieyongji@baidu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yongji Xie <elohimes@gmail.com>
Previously, if the size of initrd >=2G, qemu exits with error:
root@haswell-OptiPlex-9020:/home/lizj# /home/lizhijian/lkp/qemu-colo/x86_64-softmmu/qemu-system-x86_64 -kernel ./vmlinuz-4.16.0-rc4 -initrd large.cgz -nographic
qemu: error reading initrd large.cgz: No such file or directory
root@haswell-OptiPlex-9020:/home/lizj# du -sh large.cgz
2.5G large.cgz
this patch changes the caller side that use this function to calculate
size of initrd file as well.
v2: update error message and int64_t printing format
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Message-Id: <1536833233-14121-1-git-send-email-lizhijian@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
error_report and friends already add a "qemu-system-xxx" prefix
to the string, so a "qemu:" prefix is redundant in the string.
Just drop it.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1537495530-580-1-git-send-email-maozhongyi@cmss.chinamobile.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Commit
10efd7e108 "pc: acpi: fix memory hotplug regression by reducing stub SRAT entry size"
attemped to fix hotplug regression introduced by
848a1cc1e "hw/acpi-build: build SRAT memory affinity structures for DIMM devices"
fixed issue for Windows/3.0+ linux kernels, however it regressed 2.6 based
kernels (RHEL6) to the point where guest might crash at boot.
Reason is that 2.6 kernel discards SRAT table due too small last entry
which down the road leads to crashes. Hack I've tried in 10efd7e108 is also
not ACPI spec compliant according to which whole possible RAM should be
described in SRAT. Revert 10efd7e108 to fix regression for 2.6 based kernels.
With 10efd7e108 reverted, I've also tried splitting SRAT table statically
in different ways %/node and %/slot but Windows still fails to online
2nd pc-dimm hot-plugged into node 0 (as described in 10efd7e108) and
sometimes even coldplugged pc-dimms where affected with static SRAT
partitioning.
The only known so far way where Windows stays happy is when we have 1
SRAT entry in the last node covering all hotplug area.
Revert 848a1cc1e until we come up with a way to avoid regression
on Windows with hotplug area split in several entries.
Tested this with 2.6/3.0 based kernels (RHEL6/7) and WS20[08/12/12R2/16]).
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Replace all the trace_vtd_err_*() hooks with the new error_report_once()
since they are similar to trace_vtd_err() - dumping the first error
would be mostly enough, then we have them on by default too.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180815095328.32414-4-peterx@redhat.com>
[Use "%x" instead of "%" PRIx16 to print uint16_t, whitespace tidied up]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Replace existing trace_vtd_err() with error_report_once() then stderr
will capture something if any of the error happens, meanwhile we don't
suffer from any DDOS. Then remove the trace point. Since at it,
provide more information where proper (now we can pass parameters into
the report function).
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180815095328.32414-3-peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[Two format strings fixed, whitespace tidied up]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
We can assign and verify the address before realizing and trying to plug.
reading/writing the address property should never fail for DIMMs, so let's
reduce error handling a bit by using &error_abort. Getting access to the
memory region now might however fail. So forward errors from
get_memory_region() properly.
As all memory devices should use the alignment of the underlying memory
region for guest physical address asignment, do detection of the
alignment in pc_dimm_pre_plug(), but allow pc.c to overwrite the
alignment for compatibility handling.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180801133444.11269-5-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All applicable memory regions always have an alignment > 0. All memory
backends result in file_ram_alloc() or qemu_anon_ram_alloc() getting
called, setting the alignment to > 0.
So a PCDIMM memory region always has an alignment > 0. NVDIMM copy the
alignment of the original memory memory region into the handcrafted memory
region that will be used at this place.
So the check for 0 can be dropped and we can reduce the special
handling.
Dropping this check makes factoring out of alignment handling easier as
compat handling only has to look at pcmc->enforce_aligned_dimm and not
care about the alignment of the memory region.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180801133444.11269-4-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We can assign and verify the slot before realizing and trying to plug.
reading/writing the slot property should never fail, so let's reduce
error handling a bit by using &error_abort.
To do this during pre_plug, add and use (x86, ppc) pc_dimm_pre_plug().
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180801133444.11269-2-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 848a1cc1e (hw/acpi-build: build SRAT memory affinity structures for DIMM devices)
broke the first dimm hotplug in following cases:
1: there is no coldplugged dimm in the last numa node
but there is a coldplugged dimm in another node
-m 4096,slots=4,maxmem=32G \
-object memory-backend-ram,id=m0,size=2G \
-device pc-dimm,memdev=m0,node=0 \
-numa node,nodeid=0 \
-numa node,nodeid=1
2: if order of dimms on CLI is:
1st plugged dimm in node1
2nd plugged dimm in node0
-m 4096,slots=4,maxmem=32G \
-object memory-backend-ram,size=2G,id=m0 \
-device pc-dimm,memdev=m0,node=1 \
-object memory-backend-ram,id=m1,size=2G \
-device pc-dimm,memdev=m1,node=0 \
-numa node,nodeid=0 \
-numa node,nodeid=1
(qemu) object_add memory-backend-ram,id=m2,size=1G
(qemu) device_add pc-dimm,memdev=m2,node=0
the first DIMM hotplug to any node except the last one
fails (Windows is unable to online it).
Length reduction of stub hotplug memory SRAT entry,
fixes issue for some reason.
RHBZ: 1609234
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The multiboot code parses the initrd_filename twice, first to count how
many entries there are, and second to process each entry. This changes
the first loop to store the parse module names in a list, and the second
loop can now use these names. This avoids having to pass NULL to the
get_opt_value() method which means it can safely assume a non-NULL param.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20180514171913.17664-3-berrange@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The logic for parsing the multiboot initrd modules was messed up in
commit 950c4e6c94
Author: Daniel P. Berrangé <berrange@redhat.com>
Date: Mon Apr 16 12:17:43 2018 +0100
opts: don't silently truncate long option values
Causing the length to be undercounter, and the number of modules over
counted. It also passes NULL to get_opt_value() which was not robust
at accepting a NULL value.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20180514171913.17664-2-berrange@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Hyper-V identifies vCPUs by Virtual Processor (VP) index which can be
queried by the guest via HV_X64_MSR_VP_INDEX msr. It is defined by the
spec as a sequential number which can't exceed the maximum number of
vCPUs per VM.
It has to be owned by QEMU in order to preserve it across migration.
However, the initial implementation in KVM didn't allow to set this
msr, and KVM used its own notion of VP index. Fortunately, the way
vCPUs are created in QEMU/KVM makes it likely that the KVM value is
equal to QEMU cpu_index.
So choose cpu_index as the value for vp_index, and push that to KVM on
kernels that support setting the msr. On older ones that don't, query
the kernel value and assert that it's in sync with QEMU.
Besides, since handling errors from vCPU init at hotplug time is
impossible, disable vCPU hotplug.
This patch also introduces accessor functions to encapsulate the mapping
between a vCPU and its vp_index.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180702134156.13404-3-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A couple of fixes to amd iommu, and a fix to virtio iommu.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbND4FAAoJECgfDbjSjVRpPfMH/20ND3U1FM65HtH0DNg62ABl
qGcgyQvwSTBG74IEBoDAvZPXJ7s2OPDSdcKGoHgGMGLWYU/Xno6GR6G8dKW0U9Jk
/FOfhGEITFBCBsvzXM40+HqHhL2iNkw2PGt3aJqtx8BHJEnPzBmCKEIl6NmYHi9d
dp9iMerYaJtXWDyPGwk0vEFZTsjQomRz33KyRF2jGM/8QJH5X50UuYaDGQHTA6OH
5LSIfOf39hcXxssTAR+nZjJQIbNcJ5vXHXgGWWlA0TBF0/0eoJLsFehEEVKlLjUy
1bzM/90SgrTFFbJWULm1Y/0phAl02v/4NSKWg2x2hlJDRbttHrskVg4Y5p5wmvo=
=y+sn
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, virtio: fixes
A couple of fixes to amd iommu, and a fix to virtio iommu.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 28 Jun 2018 02:46:45 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
virtio-rng: process pending requests on DRIVER_OK
hw/i386: Fix AMDVI GATS and HATS encodings
hw/i386: Fix IVHD entry length for AMD IOMMU
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It eases code review, unit is explicit.
Patch generated using:
$ git grep -E '[<>][<>]=? ?[1-5]0' hw/ include/hw/
and modified manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It eases code review, unit is explicit.
Patch generated using:
$ git grep -E '(1024|2048|4096|8192|(<<|>>).?(10|20|30))' hw/ include/hw/
and modified manually.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alan Robinson <Alan.Robinson@ts.fujitsu.com>
Message-Id: <20180625124238.25339-12-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Let's start to use "info pic" just like other platforms. For now we
keep the command for a while so that old users can know what is the new
command to use.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171229073104.3810-6-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This include both userspace and in-kernel ioapic. Note that the numbers
can be inaccurate for kvm-ioapic. One reason is the same with
kvm-i8259, that when irqfd is used, irqs can be delivered all inside
kernel without our notice. Meanwhile, kvm-ioapic is specially treated
when irq numbers <ISA_NUM_IRQS, those irqs will be delivered in kernel
too via kvm-i8259 (please refer to kvm_pc_gsi_handler).
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171229073104.3810-5-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Let's try to reduce error handling a bit. In the plug/unplug case, the
device was realized and therefore we can assume that getting access to
the memory region will not fail.
For get_vmstate_memory_region() this is already handled that way.
Document both cases.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-13-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We can perform these checks before the device is actually realized.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-6-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Let's rename it to make it look more consistent.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-4-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use a similar naming scheme as spapr. This way, we can go ahead and
rename e.g. pc_dimm_memory_plug to pc_dimm_plug, which avoids
confusion.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-3-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We support up to 6 levels, but those are encoded as 10b according to the
AMD IOMMU spec (chapter 3.3.1, Extended Feature Register).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Counting from the IVHD ID field to the all-devices entry, we have 28
bytes, not 36.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The oldest machine type which is still used in a still maintained distro
is a pc-0.12 based machine type in RHEL6, so everything that is older
than pc-0.12 should not be used anymore. Thus let's deprecate pc-0.10
and pc-0.11 so that we can finally remove them in a future release.
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1529917512-10528-1-git-send-email-thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add an IOMMU index argument to the translate method of
IOMMUs. Since all of our current IOMMU implementations
support only a single IOMMU index, this has no effect
on the behaviour.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180604152941.20374-4-peter.maydell@linaro.org
Add support for multiple IOMMU indexes to the IOMMU notifier APIs.
When initializing a notifier with iommu_notifier_init(), the caller
must pass the IOMMU index that it is interested in. When a change
happens, the IOMMU implementation must pass
memory_region_notify_iommu() the IOMMU index that has changed and
that notifiers must be called for.
IOMMUs which support only a single index don't need to change.
Callers which only really support working with IOMMUs with a single
index can use the result of passing MEMTXATTRS_UNSPECIFIED to
memory_region_iommu_attrs_to_index().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180604152941.20374-3-peter.maydell@linaro.org
A link property can be set during creation, with
object_property_add_link() and later with object_property_set_link().
add_link() doesn't add a reference to the target object, while
set_link() does.
Furthemore, OBJ_PROP_LINK_UNREF_ON_RELEASE flags, set during add_link,
says whether a reference must be released when the property is destroyed.
This can lead to leaks if the property was later set_link(), as the
added reference is never released.
Instead, rename OBJ_PROP_LINK_UNREF_ON_RELEASE to OBJ_PROP_LINK_STRONG
and use that has an indication on how the link handle reference
management in set_link().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180531195119.22021-3-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Replace the "nvdimm-cap" option which took numeric arguments such as "2"
with a more user friendly "nvdimm-persistence" option which takes symbolic
arguments "cpu" or "mem-ctrl".
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
commit f548222c added PC_COMPAT_2_12 to the 3.0 PC machine-types.
I believe this happened during manual conflict resolution when
applying the patch.
Cc: Xiao Guangrong <xiaoguangrong@tencent.com>
Cc: Juan Quintela <quintela@redhat.com>
Fixes: f548222c24
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20180608192940.19548-1-ehabkost@redhat.com>
Reviewed-by: Marcel Apfelbaum<marcel.apfelbaum@gmail.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbEXNvAAoJECgfDbjSjVRpc8gH/R8xrcFrV+k9wwbgYcOcGb6Y
LWjseE31pqJcxRV80vLOdzYEuLStZQKQQY7xBDMlA5vdyvZxIA6FLO2IsiJSbFAk
EK8pclwhpwQAahr8BfzenabohBv2UO7zu5+dqSvuJCiMWF3jGtPAIMxInfjXaOZY
odc1zY2D2EgsC7wZZ1hfraRbISBOiRaez9BoGDKPOyBY9G1ASEgxJgleFgoBLfsK
a1XU+fDM6hAVdxftfkTm0nibyf7PWPDyzqghLqjR9WXLvZP3Cqud4p8N29mY51pR
KSTjA4FYk6Z9EVMltyBHfdJs6RQzglKjxcNGdlrvacDfyFi79fGdiosVllrjfJM=
=3+V0
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
acpi, vhost, misc: fixes, features
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 01 Jun 2018 17:25:19 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (31 commits)
vhost-blk: turn on pre-defined RO feature bit
ACPI testing: test NFIT platform capabilities
nvdimm, acpi: support NFIT platform capabilities
tests/.gitignore: add entry for generated file
arch_init: sort architectures
ui: use local path for local headers
qga: use local path for local headers
colo: use local path for local headers
migration: use local path for local headers
usb: use local path for local headers
sd: fix up include
vhost-scsi: drop an unused include
ppc: use local path for local headers
rocker: drop an unused include
e1000e: use local path for local headers
ioapic: fix up includes
ide: use local path for local headers
display: use local path for local headers
trace: use local path for local headers
migration: drop an unused include
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QEMU 3.0 enables strict check for compression & decompression to
make the migration more robust, that depends on the source to fix
the internal design which triggers the unexpected error conditions
To make it work for migrating old version QEMU to 2.13 QEMU, we
introduce this parameter to disable the error check on the
destination which is the default behavior of the machine type
which is older than 2.13, alternately, the strict check can be
enabled explicitly as followings:
-M pc-q35-2.11 -global migration.decompress-error-check=true
Signed-off-by: Xiao Guangrong <xiaoguangrong@tencent.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Add a machine command line option to allow the user to control the Platform
Capabilities Structure in the virtualized NFIT. This Platform Capabilities
Structure was added in ACPI 6.2 Errata A.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The function has been deprecated for 2.5 years, and there are just a handful
of users. Convert them to memory_region_init_io with NULL callbacks,
and while at it pass the right device as the owner.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-20-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum<marcel.apfelbaum@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove those unneeded includes to speed up the compilation
process a little bit.
Code change produced with:
$ git grep '#include "sysemu/blockdev.h"' | \
cut -d: -f-1 | \
xargs egrep -L "(BlockInterfaceType|DriveInfo|drive_get|blk_legacy_dinfo|blockdev_mark_auto_del)" | \
xargs sed -i.bak '/#include "sysemu\/blockdev.h"/d'
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-15-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch removes the current hackery where IOREQ_TYPE_PCI_CONFIG
requests are handled by faking PIO to 0xcf8 and 0xcfc and replaces it
with direct calls to pci_host_config_read/write_common().
Doing so necessitates mapping BDFs to PCIDevices but maintaining a simple
QLIST in xen_device_realize/unrealize() will suffice.
NOTE: whilst config space accesses are currently limited to
PCI_CONFIG_SPACE_SIZE, this patch paves the way to increasing the
limit to PCIE_CONFIG_SPACE_SIZE when Xen gains the ability to
emulate MCFG table accesses.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Xen 4.11 has a new API to directly map guest resources. Among the resources
that can be mapped using this API are ioreq pages.
This patch modifies QEMU to attempt to use the new API should it exist,
falling back to the previous mechanism if it is unavailable.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
When global_log_dirty is enabled VRAM modification tracking never
worked correctly. The address that is passed to xen_hvm_modified_memory()
is not the effective PFN but RAM block address which is not the same
for VRAM.
We need to make a translation for this address into PFN using
physmap. Since there is no way to access physmap properly inside
xen_hvm_modified_memory() let's make it a global structure.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Rename the 2.13 machine types to match what we're going to
use as our next release number.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-id: 20180522104000.9044-3-peter.maydell@linaro.org
Beginning of merging vDPA, new PCI ID, a new virtio balloon stat, intel
iommu rework fixing a couple of security problems (no CVEs yet), fixes
all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbBX2cAAoJECgfDbjSjVRpOEYIAIR6KGkwbAJ9SnO9B71DQHl1
yYYgM7i2HwyZ1YPnXOYWnI1lzQ1bARTf2krQJFGmfjlDaueFf9KnXdNByoVCmG8m
UhF/rQp3DcJ4wTABktPtME8gWdQxKPmDxlN5W3f29Zrm3g9S+Hshi+sfPZUkBxL4
gQMFRctb2SxvQXG+lusHVwo1oF6pzGZMmX35906he3m4xS/cfoeCP7Qj6nSvHZq7
lsLoOeYxHtXWA9gTYxpd7zW+hhUxkspoOqcXySHfO7e5enJANaulTxKuC0T+6HL4
O2iUM+1wjUYE0tQcNJ6x7emA82k5OdG2OMD6gbR1oSdquttJo7+4R+goqpb44rc=
=NUoY
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, pci, virtio, vhost: fixes, features
Beginning of merging vDPA, new PCI ID, a new virtio balloon stat, intel
iommu rework fixing a couple of security problems (no CVEs yet), fixes
all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 23 May 2018 15:41:32 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (28 commits)
intel-iommu: rework the page walk logic
util: implement simple iova tree
intel-iommu: trace domain id during page walk
intel-iommu: pass in address space when page walk
intel-iommu: introduce vtd_page_walk_info
intel-iommu: only do page walk for MAP notifiers
intel-iommu: add iommu lock
intel-iommu: remove IntelIOMMUNotifierNode
intel-iommu: send PSI always even if across PDEs
nvdimm: fix typo in label-size definition
contrib/vhost-user-blk: enable protocol feature for vhost-user-blk
hw/virtio: Fix brace Werror with clang 6.0.0
libvhost-user: Send messages with no data
vhost-user+postcopy: Use qemu_set_nonblock
virtio: support setting memory region based host notifier
vhost-user: support receiving file descriptors in slave_read
vhost-user: add Net prefix to internal state structure
linux-headers: add kvm header for mips
linux-headers: add unistd.h on all arches
update-linux-headers.sh: unistd.h, kvm consistency
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch fixes a potential small window that the DMA page table might
be incomplete or invalid when the guest sends domain/context
invalidations to a device. This can cause random DMA errors for
assigned devices.
This is a major change to the VT-d shadow page walking logic. It
includes but is not limited to:
- For each VTDAddressSpace, now we maintain what IOVA ranges we have
mapped and what we have not. With that information, now we only send
MAP or UNMAP when necessary. Say, we don't send MAP notifies if we
know we have already mapped the range, meanwhile we don't send UNMAP
notifies if we know we never mapped the range at all.
- Introduce vtd_sync_shadow_page_table[_range] APIs so that we can call
in any places to resync the shadow page table for a device.
- When we receive domain/context invalidation, we should not really run
the replay logic, instead we use the new sync shadow page table API to
resync the whole shadow page table without unmapping the whole
region. After this change, we'll only do the page walk once for each
domain invalidations (before this, it can be multiple, depending on
number of notifiers per address space).
While at it, the page walking logic is also refactored to be simpler.
CC: QEMU Stable <qemu-stable@nongnu.org>
Reported-by: Jintack Lim <jintack@cs.columbia.edu>
Tested-by: Jintack Lim <jintack@cs.columbia.edu>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch only modifies the trace points.
Previously we were tracing page walk levels. They are redundant since
we have page mask (size) already. Now we trace something much more
useful which is the domain ID of the page walking. That can be very
useful when we trace more than one devices on the same system, so that
we can know which map is for which domain.
CC: QEMU Stable <qemu-stable@nongnu.org>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We pass in the VTDAddressSpace too. It'll be used in the follow up
patches.
CC: QEMU Stable <qemu-stable@nongnu.org>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
During the recursive page walking of IOVA page tables, some stack
variables are constant variables and never changed during the whole page
walking procedure. Isolate them into a struct so that we don't need to
pass those contants down the stack every time and multiple times.
CC: QEMU Stable <qemu-stable@nongnu.org>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For UNMAP-only IOMMU notifiers, we don't need to walk the page tables.
Fasten that procedure by skipping the page table walk. That should
boost performance for UNMAP-only notifiers like vhost.
CC: QEMU Stable <qemu-stable@nongnu.org>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
SECURITY IMPLICATION: this patch fixes a potential race when multiple
threads access the IOMMU IOTLB cache.
Add a per-iommu big lock to protect IOMMU status. Currently the only
thing to be protected is the IOTLB/context cache, since that can be
accessed even without BQL, e.g., in IO dataplane.
Note that we don't need to protect device page tables since that's fully
controlled by the guest kernel. However there is still possibility that
malicious drivers will program the device to not obey the rule. In that
case QEMU can't really do anything useful, instead the guest itself will
be responsible for all uncertainties.
CC: QEMU Stable <qemu-stable@nongnu.org>
Reported-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
That is not really necessary. Removing that node struct and put the
list entry directly into VTDAddressSpace. It simplfies the code a lot.
Since at it, rename the old notifiers_list into vtd_as_with_notifiers.
CC: QEMU Stable <qemu-stable@nongnu.org>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
SECURITY IMPLICATION: without this patch, any guest with both assigned
device and a vIOMMU might encounter stale IO page mappings even if guest
has already unmapped the page, which may lead to guest memory
corruption. The stale mappings will only be limited to the guest's own
memory range, so it should not affect the host memory or other guests on
the host.
During IOVA page table walking, there is a special case when the PSI
covers one whole PDE (Page Directory Entry, which contains 512 Page
Table Entries) or more. In the past, we skip that entry and we don't
notify the IOMMU notifiers. This is not correct. We should send UNMAP
notification to registered UNMAP notifiers in this case.
For UNMAP only notifiers, this might cause IOTLBs cached in the devices
even if they were already invalid. For MAP/UNMAP notifiers like
vfio-pci, this will cause stale page mappings.
This special case doesn't trigger often, but it is very easy to be
triggered by nested device assignments, since in that case we'll
possibly map the whole L2 guest RAM region into the device's IOVA
address space (several GBs at least), which is far bigger than normal
kernel driver usages of the device (tens of MBs normally).
Without this patch applied to L1 QEMU, nested device assignment to L2
guests will dump some errors like:
qemu-system-x86_64: VFIO_MAP_DMA: -17
qemu-system-x86_64: vfio_dma_map(0x557305420c30, 0xad000, 0x1000,
0x7f89a920d000) = -17 (File exists)
CC: QEMU Stable <qemu-stable@nongnu.org>
Acked-by: Jason Wang <jasowang@redhat.com>
[peterx: rewrite the commit message]
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Switch to the header we imported from Linux,
this allows us to drop a hack in kvm_i386.h.
More code will be dropped in the next patch.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The code is sufficiently substantial that it improves code readability
to put it in a new function called by xen_hvm_init() rather than having
it inline.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
This should help to avoid problems with accessing the device after
migration/resume without PV drivers by migrating its PCI configuration
space state. Without an explicitly defined state record it resets
every time a VM migrates which confuses the OS and makes every
access to xen-pvdevice MMIO region to fail. PV tools enable some
logic to save and restore PCI configuration state from within the VM
every time it migrates which basically hides the issue.
Older systems will acquire the new record when migrated which should
not change their state for worse.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
* dtc configure fixes
* MemoryRegionCache second try
* Deprecated option removal
* add support for Hyper-V reenlightenment MSRs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJa9Y2qAAoJEL/70l94x66Df8EIAI4pi+zf1mTlH0Koi+oqOg+d
geBC6N9IA+n1p90XERnPbuiT19NjON2R1Z907SbzDkijxdNRoYUoQf7Z+ZBTENjn
dYsVvgLYzajGLWWtJetPPaNFAqeF2z8B3lbVQnGVLzH5pQQ2NS1NJsvXQA2LslLs
2ll1CJ2EEBhayoBSbHK+0cY85f+DUgK/T1imIV2T/rwcef9Rw218nvPfGhPBSoL6
tI2xIOxz8bBOvZNg2wdxpaoPuDipBFu6koVVbaGSgXORg8k5CEcKNxInztufdELW
KZK5ORa3T0uqu5T/GGPAfm/NbYVQ4aTB5mddshsXtKbBhnbSfRYvpVsR4kQB/Hc=
=oC1r
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Don't silently truncate extremely long words in the command line
* dtc configure fixes
* MemoryRegionCache second try
* Deprecated option removal
* add support for Hyper-V reenlightenment MSRs
# gpg: Signature made Fri 11 May 2018 13:33:46 BST
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (29 commits)
rename included C files to foo.inc.c, remove osdep.h
pc-dimm: fix error messages if no slots were defined
build: Silence dtc directory creation
shippable: Remove Debian 8 libfdt kludge
configure: Display if libfdt is from system or git
configure: Really use local libfdt if the system one is too old
i386/kvm: add support for Hyper-V reenlightenment MSRs
qemu-doc: provide details of supported build platforms
qemu-options: Remove deprecated -no-kvm-irqchip
qemu-options: Remove deprecated -no-kvm-pit-reinjection
qemu-options: Bail out on unsupported options instead of silently ignoring them
qemu-options: Remove remainders of the -tdf option
qemu-options: Mark -virtioconsole as deprecated
target/i386: sev: fix memory leaks
opts: don't silently truncate long option values
opts: don't silently truncate long parameter keys
accel: use g_strsplit for parsing accelerator names
update-linux-headers: drop hyperv.h
qemu-thread: always keep the posix wrapper layer
exec: reintroduce MemoryRegion caching
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
By default MachineClass::get_hotplug_handler is NULL and concrete board
should set it to it's own handler.
Considering there isn't any default handler, drop saving empty
MachineClass::get_hotplug_handler in child class and make PC code
consistent with spapr/s390x boards.
We can bring this back when actual usecase surfaces and do it
consistently across boards that use get_hotplug_handler().
Suggested-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-id: 1525691524-32265-2-git-send-email-imammedo@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's make it clear that we are dealing with device memory. That it can
be used for memory hotplug is just a special case.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-10-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We use the machine internally either way, so let's just pass it in then.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-5-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We can just query it ourselves. When unplugging, we should always be
able to the region (as it was previously plugged). E.g. PPC already
assumed that and used &error_abort.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-4-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Let's allow to query the MemoryHotplugState directly from the machine.
If the pointer is NULL, the machine does not support memory devices. If
the pointer is !NULL, the machine supports memory devices and the
data structure contains information about the applicable physical
guest address space region.
This allows us to generically detect if a certain machine has support
for memory devices, and to generically manage it (find free address
range, plug/unplug a memory region).
We will rename "MemoryHotplugState" to something more meaningful
("DeviceMemory") after we completed factoring out the pc-dimm code into
MemoryDevice code.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-3-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
[ehabkost: rebased series, solved conflicts at spapr.c]
[ehabkost: squashed fix to use g_malloc0()]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
On the qmp level, we already have the concept of memory devices:
"query-memory-devices"
Right now, we only support NVDIMM and PCDIMM.
We want to map other devices later into the address space of the guest.
Such device could e.g. be virtio devices. These devices will have a
guest memory range assigned but won't be exposed via e.g. ACPI. We want
to make them look like memory device, but not glued to pc-dimm.
Especially, it will not always be possible to have TYPE_PC_DIMM as a parent
class (e.g. virtio devices). Let's use an interface instead. As a first
part, convert handling of
- qmp_pc_dimm_device_list
- get_plugged_memory_size
to our new model. plug/unplug stuff etc. will follow later.
A memory device will have to provide the following functions:
- get_addr(): Necessary, as the property "addr" can e.g. not be used for
virtio devices (already defined).
- get_plugged_size(): The amount this device offers to the guest as of
now.
- get_region_size(): Because this can later on be bigger than the
plugged size.
- fill_device_info(): Fill MemoryDeviceInfo, e.g. for qmp.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-2-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Now that we can safely call QOBJECT() on QObject * as well as its
subtypes, we can have macros qobject_ref() / qobject_unref() that work
everywhere instead of having to use QINCREF() / QDECREF() for QObject
and qobject_incref() / qobject_decref() for its subtypes.
The replacement is mechanical, except I broke a long line, and added a
cast in monitor_qmp_cleanup_req_queue_locked(). Unlike
qobject_decref(), qobject_unref() doesn't accept void *.
Note that the new macros evaluate their argument exactly once, thus no
need to shout them.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20180419150145.24795-4-marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Rebased, semantic conflict resolved, commit message improved]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Xen unstable (to be in 4.11) has two new dmops, relocate_memory and
pin_memory_cacheattr. Use these to set up the VGA memory, replacing the
previous calls to libxc. This allows the VGA console to work properly
when QEMU is running restricted (-xen-domid-restrict).
Wrapper functions are provided to allow QEMU to work with older versions
of Xen.
Tweak the error handling while making this change:
* Report pin_memory_cacheattr errors.
* Report errors even when DEBUG_HVM is not set. This is useful for
trying to understand why VGA is not working, since otherwise it just
fails silently.
* Fix the return values when an error occurs. The functions now
consistently return -1 and set errno.
CC: Ian Jackson <ian.jackson@eu.citrix.com>
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Ian Jackson <ian.jackson@eu.citrix.com>
Signed-off-by: Ian Jackson <ian.jackson@eu.citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
xc_interface_open etc. is not going to work if we have dropped
privilege, but xendevicemodel_shutdown will if everything is new
enough.
xendevicemodel_shutdown is only availabe in Xen 4.10 and later, so
provide a stub for earlier versions.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
We are going to want to reuse this.
No functional change.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
We need to restrict *all* the control fds that qemu opens. Looking in
/proc/PID/fd shows there are many; their allocation seems scattered
throughout Xen support code in qemu.
We must postpone the restrict call until roughly the same time as qemu
changes its uid, chroots (if applicable), and so on.
There doesn't seem to be an appropriate hook already. The RunState
change hook fires at different times depending on exactly what mode
qemu is operating in.
And it appears that no-one but the Xen code wants a hook at this phase
of execution. So, introduce a bare call to a new function
xen_setup_post, just before os_setup_post. Also provide the
appropriate stub for when Xen compilation is disabled.
We do the restriction before rather than after os_setup_post, because
xen_restrict may need to open /dev/null, and os_setup_post might have
called chroot.
Currently this does not work with migration, because when running as
the Xen device model qemu needs to signal to the toolstack that it is
ready. It currently does this using xenstore, and for incoming
migration (but not for ordinary startup) that happens after
os_setup_post.
It is correct that this happens late: we want the incoming migration
stream to be processed by a restricted qemu. The fix for this will be
to do the startup notification a different way, without using
xenstore. (QMP is probably a reasonable choice.)
So for now this restriction feature cannot be used in conjunction with
migration. (Note that this is not a regression in this patch, because
previously the -xen-restrict-domid call was, in fact, simply
ineffective!) We will revisit this in the Xen 4.11 release cycle.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
CC: Paolo Bonzini <pbonzini@redhat.com> (maintainer:X86)
CC: Richard Henderson <rth@twiddle.net> (maintainer:X86)
CC: Eduardo Habkost <ehabkost@redhat.com> (maintainer:X86)
CC: Michael S. Tsirkin <mst@redhat.com> (supporter:PC)
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
The ISA serial port handling in serial-isa.c imposes a limit
of 4 serial ports. This is because we only know of 4 IO port
and IRQ settings for them, and is unrelated to the generic
MAX_SERIAL_PORTS limit, though they happen to both be set at
4 currently.
Use a new MAX_ISA_SERIAL_PORTS wherever that is the correct
limit to be checking against.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180420145249.32435-11-peter.maydell@linaro.org
When migrating from a pre-2.9 QEMU, no clock_is_reliable flag is
transferred. We should assume that the source host has an unreliable
KVM_GET_CLOCK, rather than using whatever was determined locally, to
ensure that any drift from the TSC-based value calculated by the guest
is corrected.
Signed-off-by: Michael Chapman <mike@very.puzzling.org>
Message-Id: <20180406053406.774-1-mike@very.puzzling.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
I couldn't find a case where this prevents something bad from happening
that isn't already caught by other checks, but let's err on the safe
side and check that mh_header_addr is as expected.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Jack Schwartz <jack.schwartz@oracle.com>
The code path where mh_load_end_addr is non-zero in the Multiboot
header checks that mh_load_end_addr >= mh_load_addr and so
mb_load_size is checked. However, mb_load_size is not checked when
calculated from the file size, when mh_load_end_addr is 0.
If the kernel binary size is larger than can fit in the address space
after load_addr, we ended up with a kernel_size that is smaller than
load_size, which means that we read the file into a too small buffer.
Add a check to reject kernel files with such Multiboot headers.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Jack Schwartz <jack.schwartz@oracle.com>
ACPI 6.2A Table 5-129 "SPA Range Structure" requires the proximity
domain of a NVDIMM SPA range must match with corresponding entry in
SRAT table.
The address ranges of vNVDIMM in QEMU are allocated from the
hot-pluggable address space, which is entirely covered by one SRAT
memory affinity structure. However, users can set the vNVDIMM
proximity domain in NFIT SPA range structure by the 'node' property of
'-device nvdimm' to a value different than the one in the above SRAT
memory affinity structure.
In order to solve such proximity domain mismatch, this patch builds
one SRAT memory affinity structure for each DIMM device present at
boot time, including both PC-DIMM and NVDIMM, with the proximity
domain specified in '-device pc-dimm' or '-device nvdimm'.
The remaining hot-pluggable address space is covered by one or multiple
SRAT memory affinity structures with the proximity domain of the last
node as before.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch was generated using the following Coccinelle script:
@@
expression Obj;
@@
(
- qobject_to_qnum(Obj)
+ qobject_to(QNum, Obj)
|
- qobject_to_qstring(Obj)
+ qobject_to(QString, Obj)
|
- qobject_to_qdict(Obj)
+ qobject_to(QDict, Obj)
|
- qobject_to_qlist(Obj)
+ qobject_to(QList, Obj)
|
- qobject_to_qbool(Obj)
+ qobject_to(QBool, Obj)
)
and a bit of manual fix-up for overly long lines and three places in
tests/check-qjson.c that Coccinelle did not find.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-Id: <20180224154033.29559-4-mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[eblake: swap order from qobject_to(o, X), rebase to master, also a fix
to latent false-positive compiler complaint about hw/i386/acpi-build.c]
Signed-off-by: Eric Blake <eblake@redhat.com>
* SCSI fix to pass maximum transfer size (Daniel Barboza)
* chardev fixes and improved iothread support (Daniel Berrangé, Peter)
* checkpatch tweak (Eric)
* make help tweak (Marc-André)
* make more PCI NICs available with -net or -nic (myself)
* change default q35 NIC to e1000e (myself)
* SCSI support for NDOB bit (myself)
* membarrier system call support (myself)
* SuperIO refactoring (Philippe)
* miscellaneous cleanups and fixes (Thomas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJapqaMAAoJEL/70l94x66DQoUH/Rvg+a8giz/SrEA4P8D3Cb2z
4GNbNUUoy4oU0ltD5IAMskMwpOsvl1batE0D+pKIlfO9NV4+Cj2kpgo0p9TxoYqM
VCby3wRtx27zb5nVytC6M++iIKXmeEMqXmFw61I6umddNPSl4IR3hiHEE0DM+7dV
UPIOvJeEiazyQaw3Iw+ZctNn8dDBKc/+6oxP9xRcYTaZ6hB4G9RZkqGNNSLcJkk7
R0UotdjzIZhyWMOkjIwlpTF4sWv8gsYUV4bPYKMYho5B0Obda2dBM3I1kpA8yDa/
xZ5lheOaAVBZvM5aMIcaQPa65MO9hLyXFmhMOgyfpJhLBBz6Qpa4OLLI6DeTN+0=
=UAgA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Record-replay lockstep execution, log dumper and fixes (Alex, Pavel)
* SCSI fix to pass maximum transfer size (Daniel Barboza)
* chardev fixes and improved iothread support (Daniel Berrangé, Peter)
* checkpatch tweak (Eric)
* make help tweak (Marc-André)
* make more PCI NICs available with -net or -nic (myself)
* change default q35 NIC to e1000e (myself)
* SCSI support for NDOB bit (myself)
* membarrier system call support (myself)
* SuperIO refactoring (Philippe)
* miscellaneous cleanups and fixes (Thomas)
# gpg: Signature made Mon 12 Mar 2018 16:10:52 GMT
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (69 commits)
tcg: fix cpu_io_recompile
replay: update documentation
replay: save vmstate of the asynchronous events
replay: don't process async events when warping the clock
scripts/replay-dump.py: replay log dumper
replay: avoid recursive call of checkpoints
replay: check return values of fwrite
replay: push replay_mutex_lock up the call tree
replay: don't destroy mutex at exit
replay: make locking visible outside replay code
replay/replay-internal.c: track holding of replay_lock
replay/replay.c: bump REPLAY_VERSION again
replay: save prior value of the host clock
replay: added replay log format description
replay: fix save/load vm for non-empty queue
replay: fixed replay_enable_events
replay: fix processing async events
cpu-exec: fix exception_index handling
hw/i386/pc: Factor out the superio code
hw/alpha/dp264: Use the TYPE_SMC37C669_SUPERIO
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# default-configs/i386-softmmu.mak
# default-configs/x86_64-softmmu.mak
It will be extended and reused by follow up patch for ARM target.
PS:
Since it's generic function now, don't patch FIRMWARE_CTRL, DSDT
fields if they don't point to tables since platform might not
provide them and use X_ variants instead if applicable.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
build_append_foo() API doesn't need explicit endianness
conversions which eliminates a source of errors and
it makes build_fadt() look like declarative definition of
FADT table in ACPI spec, which makes it easy to review.
Also it allows easily extending FADT to support other
revisions which will be used by follow up patches
where build_fadt() will be reused for ARM target.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
move FADT data initialization out of fadt_setup() into dedicated
init_fadt_data() that will set common for pc/q35 values in
AcpiFadtData structure and acpi_get_pm_info() will complement
it with pc/q35 specific values initialization.
That will allow to get rid of fadt_setup() and generalize
build_fadt() so it could be easily extended for rev5 and
reused by ARM target.
While at it also move facs/dsdt/xdsdt offsets from build_fadt()
arg list into AcpiFadtData, as they belong to the same dataset.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
ACPI_PORT_SMI_CMD is alias for APM_CNT_IOPORT,
so make it really one instead of duplicating its value.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
next patch will need it before it gets to piix4/lpc branches
that initializes 'obj' now.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
SEV requires that guest bios must be encrypted before booting the guest.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-26-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au> (hw/ppc)
Message-Id: <20180308223946.26784-4-f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Move the header from hw/isa/ to hw/dma/
- Remove the old i386/pc dependency
- use a bool type for the high_page_enable argument
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-3-f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Again... (after 07dc788054 and 9157eee1b1).
We now extract the ISA bus specific helpers.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-2-f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow distributions to disable the Intel and/or AMD IOMMU devices.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After reviewing a patch from Philippe that removes block-backend.h
from hw/lm32/milkymist.c, I noticed that this header is included
unnecessarily in a lot of other files, too. Remove those unneeded
includes to speed up the compilation process a little bit.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1518684912-31637-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The e1000 NIC is getting old and is not a very good default for a
PCIe machine type. Change it to e1000e, which should be supported
by a good number of guests.
In particular, drivers for 82574 were added first to Linux 2.6.27 (2008)
and Windows 2008 R2. This does mean that Windows 2008 will not work
anymore with Q35 machine types and a default "-net nic -net xxx" network
configuration; it did work before because it does have an AHCI driver.
However, Windows 2008 has been declared out of main stream support
in 2015. It will get out of extended support in 2020. Windows 2008
R2 has the same end of support dates and, since the two are basically
Vista vs. Windows 7, R2 probably is more popular.
Reviewed-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Change all fprintf(stderr...) calls in hw/i386/multiboot.c to call
error_report() instead, including the mb_debug macro. Remove the "\n"
from strings passed to all modified calls, since error_report() appends
one.
Signed-off-by: Jack Schwartz <jack.schwartz@oracle.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Refer to field names when displaying fields in printf and debug statements.
Signed-off-by: Jack Schwartz <jack.schwartz@oracle.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The multiboot spec (https://www.gnu.org/software/grub/manual/multiboot/),
section 3.1.3, allows for bss_end_addr to be zero.
A zero bss_end_addr signifies there is no .bss section.
Suggested-by: Daniel Kiper <daniel.kiper@oracle.com>
Signed-off-by: Jack Schwartz <jack.schwartz@oracle.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Reviewed-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Automatic creation of SCSI controllers for "-drive if=scsi" for x86
machines was quite a bad idea (see description of commit f778a82f0c
for details). This is marked as deprecated since QEMU v2.9.0, and as
far as I know, nobody complained that this is still urgently required
anymore. Time to remove this now.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1519123357-13225-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The previous commit improved compile time by including less of the
generated QAPI headers. This is impossible for stuff defined directly
in qapi-schema.json, because that ends up in headers that that pull in
everything.
Move everything but include directives from qapi-schema.json to new
sub-module qapi/misc.json, then include just the "misc" shard where
possible.
It's possible everywhere, except:
* monitor.c needs qmp-command.h to get qmp_init_marshal()
* monitor.c, ui/vnc.c and the generated qapi-event-FOO.c need
qapi-event.h to get enum QAPIEvent
Perhaps we'll get rid of those some other day.
Adding a type to qapi/migration.json now recompiles some 120 instead
of 2300 out of 5100 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180211093607.27351-25-armbru@redhat.com>
[eblake: rebase to master]
Signed-off-by: Eric Blake <eblake@redhat.com>
In my "build everything" tree, a change to the types in
qapi-schema.json triggers a recompile of about 4800 out of 5100
objects.
The previous commit split up qmp-commands.h, qmp-event.h, qmp-visit.h,
qapi-types.h. Each of these headers still includes all its shards.
Reduce compile time by including just the shards we actually need.
To illustrate the benefits: adding a type to qapi/migration.json now
recompiles some 2300 instead of 4800 objects. The next commit will
improve it further.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180211093607.27351-24-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
[eblake: rebase to master]
Signed-off-by: Eric Blake <eblake@redhat.com>
qemu-common.h includes qemu/option.h, but most places that include the
former don't actually need the latter. Drop the include, and add it
to the places that actually need it.
While there, drop superfluous includes of both headers, and
separate #include from file comment with a blank line.
This cleanup makes the number of objects depending on qemu/option.h
drop from 4545 (out of 4743) to 284 in my "build everything" tree.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-20-armbru@redhat.com>
[Semantic conflict with commit bdd6a90a9e in block/nvme.c resolved]
The macro expansions of qdict_put_TYPE() and qlist_append_TYPE() need
qbool.h, qnull.h, qnum.h and qstring.h to compile. We include qnull.h
and qnum.h in the headers, but not qbool.h and qstring.h. Works,
because we include those wherever the macros get used.
Open-coding these helpers is of dubious value. Turn them into
functions and drop the includes from the headers.
This cleanup makes the number of objects depending on qapi/qmp/qnum.h
from 4551 (out of 4743) to 46 in my "build everything" tree. For
qapi/qmp/qnull.h, the number drops from 4552 to 21.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-10-armbru@redhat.com>
This cleanup makes the number of objects depending on qapi/error.h
drop from 1910 (out of 4743) to 1612 in my "build everything" tree.
While there, separate #include from file comment with a blank line,
and drop a useless comment on why qemu/osdep.h is included first.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-5-armbru@redhat.com>
[Semantic conflict with commit 34e304e975 resolved, OSX breakage fixed]
tpm_crb is a device for TPM 2.0 Command Response Buffer (CRB)
Interface as defined in TCG PC Client Platform TPM Profile (PTP)
Specification Family “2.0” Level 00 Revision 01.03 v22.
The PTP allows device implementation to switch between TIS and CRB
model at run time, but given that CRB is a simpler device to
implement, I chose to implement it as a different device.
The device doesn't implement other locality than 0 for now (my laptop
TPM doesn't either, so I assume this isn't so bad)
Tested with some success with Linux upstream and Windows 10, seabios &
modified ovmf. The device is recognized and correctly transmit
command/response with passthrough & emu. However, we are missing PPI
ACPI part atm.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Remove dependency of possible_cpus on 1st CPU instance,
which decouples configuration data from CPU instances that
are created using that data.
Also later it would be used for enabling early cpu to numa node
configuration at runtime qmp_query_hotpluggable_cpus() should
provide a list of available cpu slots at early stage,
before machine_init() is called and the 1st cpu is created,
so that mgmt might be able to call it and use output to set
numa mapping.
Use MachineClass::possible_cpu_arch_ids() callback to set
cpu type info, along with the rest of possible cpu properties,
to let machine define which cpu type* will be used.
* for SPAPR it will be a spapr core type and for ARM/s390x/x86
a respective descendant of CPUClass.
Move parse_numa_opts() in vl.c after cpu_model is parsed into
cpu_type so that possible_cpu_arch_ids() would know which
cpu_type to use during layout initialization.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <1515597770-268979-1-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The only user-creatable sysbus devices in qemu-system-x86_64 are
amd-iommu, intel-iommu, and xen-backend. xen-backend is handled
by xen_set_dynamic_sysbus(), so we only need to add amd-iommu and
intel-iommu.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20171125151610.20547-7-ehabkost@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The existing has_dynamic_sysbus flag makes the machine accept
every user-creatable sysbus device type on the command-line.
Replace it with a list of allowed device types, so machines can
easily accept some sysbus devices while rejecting others.
To keep exactly the same behavior as before, the existing
has_dynamic_sysbus=true assignments are replaced with a
TYPE_SYS_BUS_DEVICE entry on the allowed list. Other patches
will replace the TYPE_SYS_BUS_DEVICE entries with more specific
lists of devices.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: qemu-arm@nongnu.org
Cc: qemu-ppc@nongnu.org
Cc: xen-devel@lists.xenproject.org
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20171125151610.20547-2-ehabkost@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Starting qemu with
qemu-system-x86_64 -S -M isapc -device {amd|intel}-iommu
leads to a segfault. The code assume PCI bus is present and
tries to access the bus structure without checking.
Since Intel VT-d and AMDVI should only work with PCI, add a
check for PCI bus and return error if not present.
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Mohammed Gamal <mgamal@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Instead of having the same error checks in vtd_realize()
and amdvi_realize(), move that over to the generic
x86_iommu_realize().
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Mohammed Gamal <mgamal@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
It may be hard to read the assignment statement of "next_base", so
S/next_base += (1ULL << 32) - pcms->below_4g_mem_size;
/next_base = mem_base + mem_len;
... for readability.
No functionality change.
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The current implementation of Intel IOMMU code only supports 39 bits
iova address width. This patch provides a new parameter (x-aw-bits)
for intel-iommu to extend its address width to 48 bits but keeping the
default the same (39 bits). The reason for not changing the default
is to avoid potential compatibility problems with live migration of
intel-iommu enabled QEMU guest. The only valid values for 'x-aw-bits'
parameter are 39 and 48.
After enabling larger address width (48), we should be able to map
larger iova addresses in the guest. For example, a QEMU guest that
is configured with large memory ( >=1TB ). To check whether 48 bits
aw is enabled, we can grep in the guest dmesg output with line:
"DMAR: Host address width 48".
Signed-off-by: Prasad Singamsetty <prasad.singamsety@oracle.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The current implementation of Intel IOMMU code only supports 39 bits
host/iova address width so number of macros use hard coded values based
on that. This patch is to redefine them so they can be used with
variable address widths. This patch doesn't add any new functionality
but enables adding support for 48 bit address width.
Signed-off-by: Prasad Singamsetty <prasad.singamsety@oracle.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When -no-acpi option is used with Q35 machine type, no guest ACPI is
built, but the ACPI device is still created, so only checking the
presence of ACPI device before memory plug/unplug is not enough in
such cases. Check whether ACPI is disabled globally in addition and
fail memory plug/unplug if it's disabled.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Message-Id: <20171222015120.31730-1-haozhong.zhang@intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
More recent specs of the TPM2 ACPI table add fields for the log area
start address and the log area minimum size, which we already use
for the TCPA table.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
It should be caching-mode. It may confuse people when it pops up.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Liu, Yi L <yi.l.liu@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We have PCI_DEVFN_MAX now.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Liu, Yi L <yi.l.liu@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When compiled with anything other than the 'log' trace backend, we have:
error: implicit declaration of function 'qemu_log_mask'
error: 'LOG_UNIMP' undeclared (first use in this function)
This patch adds the missing include.
Fixes: 7299e1a411
("hw/i386/vmport: replace fprintf() by trace events or LOG_UNIMP")
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Message-id: 20171221211103.30311-1-laurent@vivier.eu
[PMM: fixed commit message description of when problem occurs]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now both classes (i8259, i8259-kvm) support this. Move this upper to
the common class code.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171210063819.14892-6-peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Let's leverage the i8259 common code for kvm-i8259 too.
I think it's still possible that stats can lost when i8259 is in kernel
and meanwhile when irqfd is used, e.g., by vfio or vhost devices.
However that should be rare IMHO since they should be using MSIs mostly
if they really want performance (that's why people use vhost and device
assignment), and no old INTx should be used. As long as the INTx users
are emulated in QEMU the stats will be correct.
For "info pic", it should be always accurate since we fetch kvm regs
before dump.
More importantly, it's just too simple to do this now - it's only 10+
LOC to gain this feature.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171210063819.14892-5-peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's a x86-only device, so it does not make sense to keep it
in the shared misc folder.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
It's a x86-only device, so it does not make sense to keep it
in the shared misc folder.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
and remove the old i386/pc dependency
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
instead move them to the source file
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
