The recently added LED device reports LED status changes with
the 'led_set_intensity' trace event. It is less invasive than
the fprintf() calls. We need however to have a binary built
with tracing support.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200912134041.946260-8-f4bug@amsat.org>
Per the 'ARM MPS2 and MPS2+ FPGA Prototyping Boards Technical
Reference Manual' (100112_0200_07_en):
2.1 Overview of the MPS2 and MPS2+ hardware
The MPS2 and MPS2+ FPGA Prototyping Boards contain the
following components and interfaces:
* User switches and user LEDs:
- Two green LEDs and two push buttons that connect to
the FPGA.
- Eight green LEDs and one 8-way dip switch that connect
to the MCC.
Add the 8 LEDs connected to the MCC.
This replaces the 'mps2_scc_leds' trace events by the generic
'led_set_intensity' event.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-Id: <20200912134041.946260-7-f4bug@amsat.org>
Per the 'ARM MPS2 and MPS2+ FPGA Prototyping Boards Technical
Reference Manual' (100112_0200_07_en):
2.1 Overview of the MPS2 and MPS2+ hardware
The MPS2 and MPS2+ FPGA Prototyping Boards contain the
following components and interfaces:
* User switches and user LEDs:
- Two green LEDs and two push buttons that connect to
the FPGA.
- Eight green LEDs and one 8-way dip switch that connect
to the MCC.
Add the 2 LEDs connected to the FPGA.
This replaces the 'mps2_fpgaio_leds' trace events by the generic
'led_set_intensity' event.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-Id: <20200912134041.946260-6-f4bug@amsat.org>
The Witherspoon has 3 LEDs connected to a PCA9552. Add them.
The names and reset values are taken from:
https://github.com/open-power/witherspoon-xml/blob/master/witherspoon.xml
Example booting obmc-phosphor-image:
$ qemu-system-arm -M witherspoon-bmc -trace led_change_intensity
1592693373.997015:led_change_intensity LED desc:'front-fault-4' color:green intensity 0% -> 100%
1592693373.997632:led_change_intensity LED desc:'front-power-3' color:green intensity 0% -> 100%
1592693373.998239:led_change_intensity LED desc:'front-id-5' color:green intensity 0% -> 100%
1592693500.291805:led_change_intensity LED desc:'front-power-3' color:green intensity 100% -> 0%
1592693500.312041:led_change_intensity LED desc:'front-power-3' color:green intensity 0% -> 100%
1592693500.821254:led_change_intensity LED desc:'front-power-3' color:green intensity 100% -> 0%
1592693501.331517:led_change_intensity LED desc:'front-power-3' color:green intensity 0% -> 100%
1592693501.841367:led_change_intensity LED desc:'front-power-3' color:green intensity 100% -> 0%
1592693502.350839:led_change_intensity LED desc:'front-power-3' color:green intensity 0% -> 100%
1592693502.861134:led_change_intensity LED desc:'front-power-3' color:green intensity 100% -> 0%
1592693503.371090:led_change_intensity LED desc:'front-power-3' color:green intensity 0% -> 100%
We notice the front-power LED starts to blink at a ~2Hz rate.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200912134041.946260-5-f4bug@amsat.org>
Track the LED intensity, and emit a trace event when it changes.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200912134041.946260-4-f4bug@amsat.org>
Some devices expose GPIO lines.
Add a GPIO qdev input to our LED device, so we can
connect a GPIO output using qdev_connect_gpio_out().
When used with GPIOs, the intensity can only be either
minium or maximum. This depends of the polarity of the
GPIO (which can be inverted).
Declare the GpioPolarity type to model the polarity.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-Id: <20200912134041.946260-3-f4bug@amsat.org>
Add a LED device which can be connected to a GPIO output.
They can also be dimmed with PWM devices. For now we do
not implement the dimmed mode, but in preparation of a
future implementation, we start using the LED intensity.
LEDs are limited to a fixed set of colors.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200912134041.946260-2-f4bug@amsat.org>
This includes:
- Improvements to logging output
- Hypervisor instruction fixups
- The ability to load a noMMU kernel
- SiFive OTP support
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAl+S8zUACgkQIeENKd+X
cFR79wf/UjQulwFofCgOh8Fsrh5tlbRVYSXEHCWkEg6V8yfA+WYkkup94wBJK0V6
tJglht7v8aovUFWRyEL+yB+zXmT88ZugW20D3NtP5aaTTuPWij2qlYDTJQK9FGEf
1rW5mFZ4VkULEEHeO6MoJ/0t50Cs4ViA//Qz6Un4Z+zVqYjkItT5NNYx9j+czLIJ
KBre/ziJXu8yIxYaxqy4Lb4IepVL5T9/pjIw5nbNbWE+DfnfqiUPVifXx73gFRPZ
zRfgDD+Dbn/bbmDl137PkpPa2hk5CNUAL8/9rEhnjji2Lrb6SH+gFc0GvnZk7DJm
duKXhegU/ATZlI+1bLqL1D1z8Do6qQ==
=H9Qu
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20201023' into staging
A collection of RISC-V fixes for the next QEMU release.
This includes:
- Improvements to logging output
- Hypervisor instruction fixups
- The ability to load a noMMU kernel
- SiFive OTP support
# gpg: Signature made Fri 23 Oct 2020 16:13:57 BST
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20201023:
hw/misc/sifive_u_otp: Add backend drive support
hw/misc/sifive_u_otp: Add write function and write-once protection
target/riscv: raise exception to HS-mode at get_physical_address
hw/riscv: Load the kernel after the firmware
hw/riscv: Add a riscv_is_32_bit() function
hw/riscv: Return the end address of the loaded firmware
hw/riscv: sifive_u: Allow specifying the CPU
target/riscv: Fix implementation of HLVX.WU instruction
target/riscv: Fix update of hstatus.GVA in riscv_cpu_do_interrupt
target/riscv: Fix update of hstatus.SPVP
hw/intc: Move sifive_plic.h to the include directory
riscv: Convert interrupt logs to use qemu_log_mask()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Initialize the object's values from the class when the object is
created, no need to have vl.c do it for us.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Clean up vl.c, default min/max/default_cpus to uniprocessor
directly in the QOM class initialization code.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The function selection fields (399:376) should be zeroed out to
prevent leftover from being or'ed into the switch function status
data structure.
This fixes the boot failure as seen in the acceptance testing on
the orangepi target.
Fixes: b638627c72 ("hw/sd: Fix incorrect populated function switch status data structure")
Reported-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201024014954.21330-1-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
I/O request length can not be negative.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200630133912.9428-15-f4bug@amsat.org>
CRC functions don't modify the buffer argument,
make it const.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200630133912.9428-14-f4bug@amsat.org>
cmd_valid_while_locked() only needs to read SDRequest->cmd,
pass it directly and make it const.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200630133912.9428-13-f4bug@amsat.org>
Add more descriptive comments to keep a clear separation
between static property vs runtime changeable.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200630133912.9428-12-f4bug@amsat.org>
Move the constants from hw/core/qdev-properties.c to
util/block-helpers.h so that knowledge of the min/max values is
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Coiby Xu <coiby.xu@gmail.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Message-id: 20200918080912.321299-5-coiby.xu@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add '-drive' support to OTP device. Allow users to assign a raw file
as OTP image.
test commands for 16k otp.img filled with zero:
$ dd if=/dev/zero of=./otp.img bs=1k count=16
$ ./qemu-system-riscv64 -M sifive_u -m 256M -nographic -bios none \
-kernel ../opensbi/build/platform/sifive/fu540/firmware/fw_payload.elf \
-d guest_errors -drive if=none,format=raw,file=otp.img
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201020033732.12921-3-green.wan@sifive.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
- Add write operation to update fuse data bit when PWE bit is on.
- Add array, fuse_wo, to store the 'written' status for all bits
of OTP to block the write operation.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-id: 20201020033732.12921-2-green.wan@sifive.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Instead of loading the kernel at a hardcoded start address, let's load
the kernel at the next aligned address after the end of the firmware.
This should have no impact for current users of OpenSBI, but will
allow loading a noMMU kernel at the start of memory.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-id: 46c00c4f15b42feb792090e3d74359e180a6d954.1602634524.git.alistair.francis@wdc.com
Instead of returning the unused entry address from riscv_load_firmware()
instead return the end address. Also return the end address from
riscv_find_and_load_firmware().
This tells the caller if a firmware was loaded and how big it is. This
can be used to determine the load address of the next image (usually the
kernel).
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-id: 558cf67162342d65a23262248b040563716628b2.1602634524.git.alistair.francis@wdc.com
Allow the user to specify the main application CPU for the sifive_u
machine.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-id: b8412086c8aea0eff30fb7a17f0acf2943381b6a.1602634524.git.alistair.francis@wdc.com
Since sifive_plic.h is used by hw/intc/sifive_plic.c,
it has to be in the public include directory. Move it.
Fixes: 84fcf3c151 ("hw/riscv: Move sifive_plic model to hw/intc")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1602578033-68384-1-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When aliasing a clock with the qdev_alias_clock() function, a new link
property is created on the device aliasing the clock. The link points
to the aliased clock and use the OBJ_PROP_LINK_STRONG flag. This
property is read only since it does not provide a check callback for
modifications.
The object_property_add_link() documentation stats that with
OBJ_PROP_LINK_STRONG properties, the linked object reference count get
decremented when the property is deleted. But it is _not_ incremented on
creation (object_property_add_link() does not actually know the link).
This commit increments the reference count on the aliased clock to
ensure the aliased clock stays alive during the property lifetime, and
to avoid a double-free memory error when the property gets deleted.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Message-Id: <20201020091024.320381-1-luc@lmichel.fr>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The SCLP boundary cross check is done by the Ultravisor for a
protected guest, hence we don't need to do it. As QEMU doesn't get a
valid SCCB address in protected mode this is even problematic and can
lead to QEMU reporting a false boundary cross error.
Fixes: db13387ca0 ("s390/sclp: rework sclp boundary checks")
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Tested-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Collin Walling <walling@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Message-Id: <20201022103135.126033-2-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Currently, a subsystem reset event leaves PCI devices enabled, causing
issues post-reset in the guest (an example would be after a kexec). These
devices need to be reset during a subsystem reset, allowing them to be
properly re-enabled afterwards. Add the S390 PCI host bridge to the list
of qdevs to be reset during subsystem reset.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: qemu-stable@nongnu.org
Message-Id: <1602767767-32713-1-git-send-email-mjrosato@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Fix two heap-overflow reported by Alexander Bulekov while fuzzing:
- https://bugs.launchpad.net/qemu/+bug/1892960
- https://bugs.launchpad.net/qemu/+bug/1895310
CI jobs results:
. https://cirrus-ci.com/build/6399328187056128
. https://gitlab.com/philmd/qemu/-/pipelines/205701966
. https://travis-ci.org/github/philmd/qemu/builds/737708930
-----BEGIN PGP SIGNATURE-----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=9A05
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd-gitlab/tags/sd-next-20201021' into staging
SD/MMC patches
Fix two heap-overflow reported by Alexander Bulekov while fuzzing:
- https://bugs.launchpad.net/qemu/+bug/1892960
- https://bugs.launchpad.net/qemu/+bug/1895310
CI jobs results:
. https://cirrus-ci.com/build/6399328187056128
. https://gitlab.com/philmd/qemu/-/pipelines/205701966
. https://travis-ci.org/github/philmd/qemu/builds/737708930
# gpg: Signature made Wed 21 Oct 2020 18:33:08 BST
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd-gitlab/tags/sd-next-20201021:
hw/sd/sdcard: Assert if accessing an illegal group
hw/sd/sdcard: Do not attempt to erase out of range addresses
hw/sd/sdcard: Reset both start/end addresses on error
hw/sd/sdcard: Do not use legal address '0' for INVALID_ADDRESS
hw/sd/sdcard: Introduce the INVALID_ADDRESS definition
hw/sd/sdcard: Add trace event for ERASE command (CMD38)
hw/sd/sdhci: Yield if interrupt delivered during multiple transfer
hw/sd/sdhci: Let sdhci_update_irq() return if IRQ was delivered
hw/sd/sdhci: Resume pending DMA transfers on MMIO accesses
hw/sd/sdhci: Stop multiple transfers when block count is cleared
hw/sd/sdhci: Fix DMA Transfer Block Size field
hw/sd/sdhci: Document the datasheet used
hw/sd/sdhci: Fix qemu_log_mask() format string
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We can not have more group than 'wpgrps_size'.
Assert if we are accessing a group above this limit.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201015063824.212980-7-f4bug@amsat.org>
While the Spec v3 is not very clear, v6 states:
If the host provides an out of range address as an argument
to CMD32 or CMD33, the card shall indicate OUT_OF_RANGE error
in R1 (ERX) for CMD38.
If an address is out of range, do not attempt to erase it:
return R1 with the error bit set.
Buglink: https://bugs.launchpad.net/qemu/+bug/1895310
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201015063824.212980-6-f4bug@amsat.org>
From the Spec "4.3.5 Erase":
The host should adhere to the following command
sequence: ERASE_WR_BLK_START, ERASE_WR_BLK_END and
ERASE (CMD38).
If an erase (CMD38) or address setting (CMD32, 33)
command is received out of sequence, the card shall
set the ERASE_SEQ_ERROR bit in the status register
and reset the whole sequence.
Reset both addresses if the ERASE command occured
out of sequence (one of the start/end address is
not set).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201015063824.212980-5-f4bug@amsat.org>
As it is legal to WRITE/ERASE the address/block 0,
change the value of this definition to an illegal
address: UINT32_MAX.
Unfortunately this break the migration stream, so
bump the VMState version number. This affects some
ARM boards and the SDHCI_PCI device (which is only
used for testing).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201015063824.212980-4-f4bug@amsat.org>
'0' is used as a value to indicate an invalid (or unset)
address. Use a definition instead of a magic value.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201015063824.212980-3-f4bug@amsat.org>
Trace addresses provided to the ERASE command.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201015063824.212980-2-f4bug@amsat.org>
The Descriptor Table has a bit to allow the DMA to generates
Interrupt when the operation of the descriptor line is completed
(see "1.13.4. Descriptor Table" of 'SD Host Controller Simplified
Specification Version 2.00').
If we have pending interrupt and the descriptor requires it
to be generated as soon as it is completed, reschedule pending
transfers and yield to the CPU.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20200903172806.489710-5-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20200903172806.489710-4-f4bug@amsat.org>
If we have pending DMA requests scheduled, process them first.
So far we don't need to implement a bottom half to process them.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20200903172806.489710-3-f4bug@amsat.org>
Add datasheet name in the file header.
We can not add the direct download link since there is a disclaimers
to agree first on the SD Association website (www.sdcard.org).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20200901140411.112150-3-f4bug@amsat.org>
Add missing newline character in qemu_log_mask() format.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20200901140411.112150-2-f4bug@amsat.org>
USB_XHCI does not depend on PCI any more.
USB_XHCI_SYSBUS must select USB_XHCI not USB.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Message-id: 20201020074844.5304-5-kraxel@redhat.com
The helper generates an acpi dsdt device entry
for the xhci sysbus device.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20201020074844.5304-4-kraxel@redhat.com
Move a bunch of defines which might be needed outside core xhci
code to that place. Add XHCI_ prefixes to avoid name clashes.
No functional change.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Message-id: 20201020074844.5304-3-kraxel@redhat.com
Add stubs for aml_interrupt and aml_memory32_fixed,
these will be needed by followup patches,
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20201020074844.5304-2-kraxel@redhat.com
Setting x86ms->pci_irq_mask to zero has the same effect,
so we don't need the has_pci argument any more.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20201016113835.17465-6-kraxel@redhat.com
Makes sure the PCI interrupt overrides are added to the
APIC table in case PCIe is enabled.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20201016113835.17465-5-kraxel@redhat.com
Add a variable to x86 machine state instead of
hard-coding the PCI interrupts.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20201016113835.17465-4-kraxel@redhat.com
Restricting xen-set-global-dirty-log and xen-load-devices-state
commands migration.json pulls slightly less QAPI-generated code
into user-mode and tools.
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20201012121536.3381997-6-philmd@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Commit 7998beb9c2 removed the ram_size initialization in the
arm_boot_info structure, however it is used by arm_load_kernel().
Initialize the field to fix:
$ qemu-system-arm -M n800 -append 'console=ttyS1' \
-kernel meego-arm-n8x0-1.0.80.20100712.1431-vmlinuz-2.6.35~rc4-129.1-n8x0
qemu-system-arm: kernel 'meego-arm-n8x0-1.0.80.20100712.1431-vmlinuz-2.6.35~rc4-129.1-n8x0' is too large to fit in RAM (kernel size 1964608, RAM size 0)
Noticed while running the test introduced in commit 050a82f0c5
("tests/acceptance: Add a test for the N800 and N810 arm machines").
Fixes: 7998beb9c2 ("arm/nseries: use memdev for RAM")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-id: 20201019095148.1602119-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
VMStateDescription.fields should be end with VMSTATE_END_OF_LIST().
However, microbit_i2c_vmstate doesn't follow it. Let's change it.
Fixes: 9d68bf564e ("arm: Stub out NRF51 TWI magnetometer/accelerometer detection")
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Peng Liang <liangpeng10@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201019093401.2993833-1-liangpeng10@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The IRQ values are defined few lines earlier, use them instead of
the magic numbers.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201017180731.1165871-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add trace events for GPU and CPU IRQs.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201017180731.1165871-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SYS_timer is not directly wired to the ARM core, but to the
SoC (peripheral) interrupt controller.
Fixes: 0e5bbd7406 ("hw/arm/bcm2835_peripherals: Use the SYS_timer")
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201010203709.3116542-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This peripheral has 1 free-running timer and 4 compare registers.
Only the free-running timer is implemented. Add support the
COMPARE registers (each register is wired to an IRQ).
Reference: "BCM2835 ARM Peripherals" datasheet [*]
chapter 12 "System Timer":
The System Timer peripheral provides four 32-bit timer channels
and a single 64-bit free running counter. Each channel has an
output compare register, which is compared against the 32 least
significant bits of the free running counter values. When the
two values match, the system timer peripheral generates a signal
to indicate a match for the appropriate channel. The match signal
is then fed into the interrupt controller.
This peripheral is used since Linux 3.7, commit ee4af5696720
("ARM: bcm2835: add system timer").
[*] https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20201010203709.3116542-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The variable holding the CTRL_STATUS register is misnamed
'status'. Rename it 'ctrl_status' to make it more obvious
this register is also used to control the peripheral.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201010203709.3116542-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use the BCM2835_SYSTIMER_COUNT definition instead of the
magic '4' value.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201010203709.3116542-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While APEI is a generic ACPI feature (usable by X86 and ARM64), only
the 'virt' machine uses it, by enabling the RAS Virtualization. See
commit 2afa8c8519: "hw/arm/virt: Introduce a RAS machine option").
Restrict the APEI tables generation code to the single user: the virt
machine. If another machine wants to use it, it simply has to 'select
ACPI_APEI' in its Kconfig.
Fixes: aa16508f1d ("ACPI: Build related register address fields via hardware error fw_cfg blob")
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Dongjiu Geng <gengdongjiu@huawei.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201008161414.2672569-1-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The time to transmit a char is expressed in nanoseconds, not in ticks.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201014213601.205222-1-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
xen-save-devices-state doesn't currently generate a vmdesc, so restore
always triggers "Expected vmdescription section, but got 0". This is
not a problem when restore comes from a file. However, when QEMU runs
in a linux stubdom and comes over a console, EOF is not received. This
causes a delay restoring - though it does restore.
Setting suppress-vmdesc skips looking for the vmdesc during restore and
avoids the wait.
The other approach would be generate a vmdesc in qemu_save_device_state.
Since COLO shared that function, and the vmdesc is just discarded on
restore, we choose to skip it.
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20201013190506.3325-1-jandryuk@gmail.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Currently a single watch on /local/domain/X/backend is registered by each
QEMU process running in service domain X (where X is usually 0). The purpose
of this watch is to ensure that QEMU is notified when the Xen toolstack
creates a new device backend area.
Such a backend area is specific to a single frontend area created for a
specific guest domain and, since each QEMU process is also created to service
a specfic guest domain, it is unnecessary and inefficient to notify all QEMU
processes.
Only the QEMU process associated with the same guest domain need
receive the notification. This patch re-factors the watch registration code
such that notifications are targetted appropriately.
Reported-by: Jerome Leseinne <jerome.leseinne@gmail.com>
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20201001081500.1026-1-paul@xen.org>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
There's no references in only file which includes xenguest.h
to any xen definitions. And there's no references to -lxenguest
in qemu, either. Drop it.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20200727140048.19779-1-mjt@msgid.tls.msk.ru>
[perard: rebased]
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
The currently existing 9pfs test cases are all solely using the 9pfs 'synth'
fileystem driver, which is a very simple and purely simulated (in RAM only)
filesystem. There are issues though where the 'synth' fs driver is not
sufficient. For example the following two bugs need test cases running the
9pfs 'local' fs driver:
https://bugs.launchpad.net/qemu/+bug/1336794https://bugs.launchpad.net/qemu/+bug/1877384
This patch set for that reason introduces 9pfs test cases using the 9pfs
'local' filesystem driver along to the already existing tests on 'synth'.
-----BEGIN PGP SIGNATURE-----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=TZ2q
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cschoenebeck/tags/pull-9p-20201019' into staging
9pfs: add tests using local fs driver
The currently existing 9pfs test cases are all solely using the 9pfs 'synth'
fileystem driver, which is a very simple and purely simulated (in RAM only)
filesystem. There are issues though where the 'synth' fs driver is not
sufficient. For example the following two bugs need test cases running the
9pfs 'local' fs driver:
https://bugs.launchpad.net/qemu/+bug/1336794https://bugs.launchpad.net/qemu/+bug/1877384
This patch set for that reason introduces 9pfs test cases using the 9pfs
'local' filesystem driver along to the already existing tests on 'synth'.
# gpg: Signature made Mon 19 Oct 2020 13:39:08 BST
# gpg: using RSA key 96D8D110CF7AF8084F88590134C2B58765A47395
# gpg: issuer "qemu_oss@crudebyte.com"
# gpg: Good signature from "Christian Schoenebeck <qemu_oss@crudebyte.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: ECAB 1A45 4014 1413 BA38 4926 30DB 47C3 A012 D5F4
# Subkey fingerprint: 96D8 D110 CF7A F808 4F88 5901 34C2 B587 65A4 7395
* remotes/cschoenebeck/tags/pull-9p-20201019:
tests/9pfs: add local Tmkdir test
tests/9pfs: add virtio_9p_test_path()
tests/9pfs: wipe local 9pfs test directory
tests/9pfs: introduce local tests
tests/9pfs: change qtest name prefix to synth
9pfs: suppress performance warnings on qtest runs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Don't trigger any performance warning if we're just running test cases,
because tests intentionally run for edge cases.
So far performance warnings were suppressed for the 'synth' fs driver
backend only. This patch suppresses them for all 9p fs driver backends.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <a2d2ff2163f8853ea782a7a1d4e6f2afd7c29ffe.1603106145.git.qemu_oss@crudebyte.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCgA8FiEEzGIauY6CIA2RXMnEW8LFb64PMh8FAl+NPIweHG1hcmsuY2F2
ZS1heWxhbmRAaWxhbmRlLmNvLnVrAAoJEFvCxW+uDzIf22AH/0e9QXSd2g7YRK2D
3NY/HuHr+lZNkDtNJanIQ9FUbmyzB9fMux4xg7BabpyY89Zwd9viivc6DrkM5fGM
12Yuq1IX/JOvolRvAMszAxUdnlLcB6OHDGrNBDyNFPK4Y87DLm86RJMTviiN/J/G
vsnCDjuxyHYtBruBbB4e6W/0nYJsfFXsopZxfV9Baain3W1uytRUW8WnjHJsvhhe
c7Dl4j5LcmXINtLn577kJIiVgZruk9FqADAnAcUM7+I0QRnhebshAoTpTzYCPAIy
LmUkr5NHtujBsa3m1zI8tjevFhCjvHOYvH6vdrMG6WO8m5DnAnv1iYYuM4xzI0yB
puOyz48=
=ShX6
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mcayland/tags/qemu-macppc-20201019' into staging
qemu-macppc updates
# gpg: Signature made Mon 19 Oct 2020 08:13:16 BST
# gpg: using RSA key CC621AB98E82200D915CC9C45BC2C56FAE0F321F
# gpg: issuer "mark.cave-ayland@ilande.co.uk"
# gpg: Good signature from "Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>" [full]
# Primary key fingerprint: CC62 1AB9 8E82 200D 915C C9C4 5BC2 C56F AE0F 321F
* remotes/mcayland/tags/qemu-macppc-20201019:
mac_oldworld: Change PCI address of macio to match real hardware
mac_oldworld: Drop some variables
mac_oldworld: Drop a variable, use get_system_memory() directly
mac_newworld: Allow loading binary ROM image
mac_oldworld: Allow loading binary ROM image
m48t59: remove legacy m48t59_init() function
ppc405_boards: use qdev properties instead of legacy m48t59_init() function
sun4u: use qdev properties instead of legacy m48t59_init() function
sun4m: use qdev properties instead of legacy m48t59_init() function
m48t59-isa: remove legacy m48t59_init_isa() function
uninorth: use qdev gpios for PCI IRQs
grackle: use qdev gpios for PCI IRQs
macio: don't reference serial_hd() directly within the device
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
. Fix some comment spelling errors
. Demacro some TCG helpers
. Add loongson-ext lswc2/lsdc2 group of instructions
. Log unimplemented cache opcode
. Increase number of TLB entries on the 34Kf core
. Allow the CPU to use dynamic frequencies
. Calculate the CP0 timer period using the CPU frequency
. Set CPU frequency for each machine
. Fix Malta FPGA I/O region size
. Allow running qtests when ROM is missing
. Add record/replay acceptance tests
. Update MIPS CPU documentation
. MAINTAINERS updates
CI jobs results:
https://gitlab.com/philmd/qemu/-/pipelines/203931842https://travis-ci.org/github/philmd/qemu/builds/736491461https://cirrus-ci.com/build/6272264062631936https://app.shippable.com/github/philmd/qemu/runs/886/summary/console
-----BEGIN PGP SIGNATURE-----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=BOxw
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd-gitlab/tags/mips-next-20201017' into staging
MIPS patches queue
. Fix some comment spelling errors
. Demacro some TCG helpers
. Add loongson-ext lswc2/lsdc2 group of instructions
. Log unimplemented cache opcode
. Increase number of TLB entries on the 34Kf core
. Allow the CPU to use dynamic frequencies
. Calculate the CP0 timer period using the CPU frequency
. Set CPU frequency for each machine
. Fix Malta FPGA I/O region size
. Allow running qtests when ROM is missing
. Add record/replay acceptance tests
. Update MIPS CPU documentation
. MAINTAINERS updates
CI jobs results:
https://gitlab.com/philmd/qemu/-/pipelines/203931842https://travis-ci.org/github/philmd/qemu/builds/736491461https://cirrus-ci.com/build/6272264062631936https://app.shippable.com/github/philmd/qemu/runs/886/summary/console
# gpg: Signature made Sat 17 Oct 2020 14:59:53 BST
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd-gitlab/tags/mips-next-20201017: (44 commits)
target/mips: Increase number of TLB entries on the 34Kf core (16 -> 64)
MAINTAINERS: Remove duplicated Malta test entries
MAINTAINERS: Downgrade MIPS Boston to 'Odd Fixes', fix Paul Burton mail
MAINTAINERS: Put myself forward for MIPS target
MAINTAINERS: Remove myself
docs/system: Update MIPS CPU documentation
tests/acceptance: Add MIPS record/replay tests
hw/mips: Remove exit(1) in case of missing ROM
hw/mips: Rename TYPE_MIPS_BOSTON to TYPE_BOSTON
hw/mips: Simplify code using ROUND_UP(INITRD_PAGE_SIZE)
hw/mips: Simplify loading 64-bit ELF kernels
hw/mips/malta: Use clearer qdev style
hw/mips/malta: Move gt64120 related code together
hw/mips/malta: Fix FPGA I/O region size
target/mips/cpu: Display warning when CPU is used without input clock
hw/mips/cps: Do not allow use without input clock
hw/mips/malta: Set CPU frequency to 320 MHz
hw/mips/boston: Set CPU frequency to 1 GHz
hw/mips/cps: Expose input clock and connect it to CPU cores
hw/mips/jazz: Correct CPU frequencies
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Check the value of mps to avoid potential divide-by-zero later in the function.
Since HCCHAR_MPS is guest controllable, this prevents a malicious/buggy guest
from crashing the QEMU process on the host.
Signed-off-by: Mauro Matteo Cascella <mcascell@redhat.com>
Reviewed-by: Paul Zimmerman <pauldzim@gmail.com>
Reported-by: Gaoning Pan <gaoning.pgn@antgroup.com>
Reported-by: Xingwei Lin <linyi.lxw@antfin.com>
Message-id: 20201015075957.268823-1-mcascell@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The EHCI Host Controller emulation attempt to locate the device
associated with a periodic isochronous transfer description (iTD) and
when this fail the host controller is reset.
But according the EHCI spec 1.0 section 5.15.2.4 Host System
Error, the host controller is supposed to reset itself only when it
failed to communicate with the Host (Operating System), like when
there's an error on the PCI bus. If a transaction fails, there's
nothing in the spec that say to reset the host controller.
This patch rework the error path so that the host controller can keep
working when the OS setup a bogus transaction, it also revert to the
behavior of the EHCI emulation to before commits:
e94682f1fe ("ehci: check device is not NULL before calling usb_ep_get()")
7011baece2 ("usb: remove unnecessary NULL device check from usb_ep_get()")
The issue has been found while trying to passthrough a USB device to a
Windows Server 2012 Xen guest via "usb-ehci", which prevent the USB
device from working in Windows. ("usb-ehci" alone works, windows only
setup this weird periodic iTD to device 127 endpoint 15 when the USB
device is passthrough.)
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Message-id: 20201014104106.2962640-1-anthony.perard@citrix.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Change several assert()s to qemu_log_mask(LOG_GUEST_ERROR...),
to prevent the guest from causing Qemu to assert. Also fix up
several existing qemu_log_mask()s to include the function name in
the message.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paul Zimmerman <pauldzim@gmail.com>
Message-id: 20200920021449.830-1-pauldzim@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The board firmware expect these to be at fixed addresses and programs
them without probing, this patch puts the macio device at the expected
PCI address.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <f14bcaf3cf129500710ba5289980a134086bd949.1602805637.git.balaton@eik.bme.hu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Values not used frequently enough may not worth putting in a local
variable, especially with names almost as long as the original value
because that does not improve readability, to the contrary it makes it
harder to see what value is used. Drop a few such variables.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <d67bc8d914a366ca6822b5190c1308d31af5c9b3.1602805637.git.balaton@eik.bme.hu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Half of the occurances already use get_system_memory() directly
instead of sysmem variable, convert the two other uses to
get_system_memory() too which seems to be more common and drop the
variable.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <b4c714e03690deb6f94f80f7a5b2af47d90550ae.1602805637.git.balaton@eik.bme.hu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Fall back to load binary ROM image if loading ELF fails. This also
moves PROM_BASE and PROM_SIZE defines to board as these are matching
the ROM size and address on this board and removes the now unused
PROM_ADDR and BIOS_SIZE defines from common mac.h.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <4d58ffe7645a0c746c8fed6aa8775c0867b624e0.1602805637.git.balaton@eik.bme.hu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The beige G3 Power Macintosh has a 4MB firmware ROM. Fix the size of
the rom region and fall back to loading a binary image with -bios if
loading ELF image failed. This allows testing emulation with a ROM
image from real hardware as well as using an ELF OpenBIOS image.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20201017155139.5A36A746331@zero.eik.bme.hu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Now that all of the callers of this function have been switched to use qdev
properties, this legacy init function can now be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20201016182739.22875-6-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This function is no longer used within the codebase.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20201016182739.22875-2-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Currently an object link property is used to pass a reference to the OpenPIC
into the PCI host bridge so that pci_unin_init_irqs() can connect the PCI
IRQs to the PIC itself.
This can be simplified by defining the PCI IRQs as qdev gpios and then wiring
up the PCI IRQs to the PIC in the New World machine init function.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201013114922.2946-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Currently an object link property is used to pass a reference to the Heathrow
PIC into the PCI host bridge so that grackle_init_irqs() can connect the PCI
IRQs to the PIC itself.
This can be simplified by defining the PCI IRQs as qdev gpios and then wiring
up the PCI IRQs to the PIC in the Old World machine init function.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201013114922.2946-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Instead use qdev_prop_set_chr() to configure the ESCC serial chardevs at the
Mac Old World and New World machine level.
Also remove the now obsolete comment referring to the use of serial_hd() and
the setting of user_creatable to false accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20201013114922.2946-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This patch updates MIPS-based machines to allow starting them without ROM.
In this case CPU starts to execute instructions from the empty memory,
but QEMU allows introspecting the machine configuration.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <159531210571.24117.231100997794891819.stgit@pasha-ThinkPad-X280>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This will make the type name constant consistent with the name of
the type checking macro.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200902224311.1321159-19-ehabkost@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Instead of using a INITRD_PAGE_MASK definition, use the
simpler INITRD_PAGE_SIZE one which allows us to simplify
the code by using directly the self-explicit ROUND_UP()
macro.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200927163943.614604-3-f4bug@amsat.org>
Since 8279006411 ("Cast ELF datatypes properly to host 64bit types")
we don't need to sign-extend the entry_point address. Remove this
unnecessary code.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200927163943.614604-2-f4bug@amsat.org>
In order to be consistent with the other code base uses,
rewrite slightly how the MIPS_MALTA object is created.
No logical change.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20201012160503.3472140-3-f4bug@amsat.org>
The 'empty_slot' region created is related to the gt64120.
Move its creation close to the gt64120 instance creation.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20201012160503.3472140-2-f4bug@amsat.org>
The FPGA present on the CoreCard has an I/O region 1MiB wide.
Refs:
- Atlas User’s Manual (Document Number: MD00005)
- Malta User’s Manual (Document Number: MD00048)
Fixes: ea85df72b6 ("mips_malta: convert to memory API")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200905213049.761949-1-f4bug@amsat.org>
Now than all QOM users provides the input clock, do not allow
using a CPS without input clock connected.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201012095804.3335117-21-f4bug@amsat.org>
The CoreLV card with ID 0x420's CPU clocked at 320 MHz. Create
a 'cpuclk' output clock and connect it to the CPU input clock.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201012095804.3335117-20-f4bug@amsat.org>
The I6400 can run at 1 GHz or more. Create a 'cpuclk'
output clock and connect it to the CPU input clock.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201012095804.3335117-19-f4bug@amsat.org>
Expose a qdev input clock named 'clk-in', and connect it to each
core to forward-propagate the clock.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201012095804.3335117-18-f4bug@amsat.org>
