A typo in the loop over SMT threads to set irq level for doorbells
when storing to DPDES meant everything was aimed at the CPU executing
the instruction.
Cc: qemu-stable@nongnu.org
Fixes: d24e80b2ae ("target/ppc: Add msgsnd/p and DPDES SMT support")
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
POWER8 does not have the ISA IRQ -> SERIRQ routing system of later
CPUs, instead all ISA IRQs are sent to the CPU via a single PSI
interrupt. There is a sanity check in the POWER8 case to ensure the
routing bits have not been set, because that would indicate a
programming error.
Those bits were incorrectly specified because of ppc bit numbering
fun. Coverity detected this as an always-zero expression.
Cc: qemu-stable@nongnu.org
Reported-by: Cédric Le Goater <clg@redhat.com>
Resolves: Coverity CID 1558829 (partially)
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The serirq routing table is split over two registers, the calculation
for the high irqs in the second register did not subtract the irq
offset. This was spotted by Coverity as a shift-by-negative. Fix this
and change the open-coded shifting and masking to use extract32()
function so it's less error-prone.
This went unnoticed because irqs >= 14 are not used in a standard
QEMU/OPAL boot, changing the first QEMU serial-isa irq to 14 to test
does demonstrate serial irqs aren't received, and that this change
fixes that.
Cc: qemu-stable@nongnu.org
Reported-by: Cédric Le Goater <clg@redhat.com>
Resolves: Coverity CID 1558829 (partially)
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
This is like commit 86e6202a57 ("target/ppc: Make divw[u] handler
method decodetree compatible."), but for gen_op_arith_divd().
Cc: qemu-stable@nongnu.org
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
divdu (without a dot) sometimes updates cr0, even though it shouldn't.
The reason is that gen_op_arith_divd() checks Rc(ctx->opcode), which is
not initialized. This field is initialized only for instructions that
go through decode_legacy(), and not decodetree.
There already was a similar issue fixed in commit 86e6202a57
("target/ppc: Make divw[u] handler method decodetree compatible.").
It's not immediately clear what else may access the uninitialized
ctx->opcode, so instead of playing whack-a-mole and changing the check
to compute_rc0, simply initialize ctx->opcode.
Cc: qemu-stable@nongnu.org
Fixes: 99082815f1 ("target/ppc: Add infrastructure for prefixed insns")
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
This is SeaBIOS for the hppa architecture v17.
If comes with some important firmware and SCSI fixes and
prepares for futher development to support 64-bit HP-UX
and MPE/UX in the future.
New PDC functions & general enhancements:
- Add PDC_MODEL_GET_INSTALL_KERNEL firmware call
- Add PDC_PAT_EVENT firmware call
- Support ENTRY_IO_BOOTOUT
- Prefer memory-access over io-access of GSP serial port
- Disable LMMIO_DIRECT0 range during modification
- Small optimizations in IODC call
Fixes:
- esp-scsi: indicate acceptance of MESSAGE IN phase data
- Avoid crash when booting without SCSI controller
- Remove exec flag from hppa-firmware.img
- Fix LMMIO detection for PCI cards on Astro/Elroy
- Avoid trashing MPE IPL bootloader stack
- HP-UX 11 64-bit saves number of RAM pages in PAGE0 at 0x33c
- Fix return value of PDC_CACHE/PDC_CACHE_RET_SPID for space id hashing
- Allow PDC functions to act when called in narrow mode
- pcidevice: Use portaddr_t for io port addresses
Cleanups:
- Change default make target to "parisc"
- Clean the "out-64" directory on "make clean"
Signed-off-by: Helge Deller <deller@gmx.de>
The 'current_fpu' field is unused since commit f01be15458
("Move the active FPU registers into env again, and use more
TCG registers to access them").
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241021151253.36443-1-philmd@linaro.org>
Similarly to commit 17c2c320f3 ("Introduce ase_mt_available helper"),
introduce the disas_mt_available() one which takes a DisasContext
argument to determine whether Multi-Threading is available by
checking the MT bit of the CP0_Config3 register.
Remove the then unused ASE_MT definition.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241024195447.44600-1-philmd@linaro.org>
Determine if the MIPS-3D ASE is implemented by checking
the state of the 3D bit in the FIR CP1 control register.
Remove the then unused ASE_MIPS3D definition.
Note, this allows using MIPS-3D on the mips64dspr2 model.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241021145832.34920-1-philmd@linaro.org>
Loongson fixed-point multiplies and divisions opcodes are
specific to 64-bit cores (Loongson-2 and Loongson-3 families).
Simplify by removing the 32-bit checks.
Reported-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Message-Id: <20241026175349.84523-10-philmd@linaro.org>
Convert the following opcodes to decodetree:
- MULT.G - multiply 32-bit signed integers
- MULTU.G - multiply 32-bit unsigned integers
- DMULT.G - multiply 64-bit signed integers
- DMULTU.G - multiply 64-bit unsigned integers
Now that all opcodes from the extension have been converted, we
can remove completely gen_loongson_integer() and its 2 calls in
decode_opc_special2_legacy() and decode_opc_special3_legacy().
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241026175349.84523-9-philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Convert the following opcodes to decodetree:
- MOD.G - mod 32-bit signed integers
- MODU.G - mod 32-bit unsigned integers
- DMOD.G - mod 64-bit signed integers
- DMODU.G - mod 64-bit unsigned integers
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20241026175349.84523-8-philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
DIV.G and DDIV.G are very similar. Provide gen_lext_DIV_G() a
'is_double' argument so it can generate DIV.G (divide 32-bit
signed integers).
With this commit we explicit the template used to generate
opcode for 32/64-bit word variants. Next commits will be less
verbose by providing both variants at once.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20241026175349.84523-6-philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Introduce decode_loongson() to decode all Loongson vendor
specific opcodes. Start converting a single opcode: DDIV.G
(divide 64-bit signed integers).
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20241026175349.84523-5-philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
There is no issue having multiple enum declarations with
the same value. As we are going to remove the OPC_MULT_G_2E
definition in few commits, restore the OPC_ADDUH_QB_DSP and
OPC_MUL_PH_DSP definitions and use them where they belong.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241026175349.84523-4-philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Since MULTU opcodes don't record the most significant bits
of the infinite result, sign-extending the sources make no
difference in the result.
Once we remove the sign extension of source registers, MULT
and MULTU are identical (as are DMULT and DMULTU).
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241026175349.84523-3-philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Extract the decode_64bit_enabled() helper which detects
whether CPUs can run 64-bit instructions.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Message-Id: <20241026175349.84523-2-philmd@linaro.org>
Enable MSA ASE for mips32r6-generic CPU.
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Faraz Shahbazker <fshahbazker@wavecomp.com>
Signed-off-by: Aleksandar Rakic <aleksandar.rakic@htecgroup.com>
Reviewed-by: Aleksandar Rikalo <arikalo@gmail.com>
Message-ID: <AM9PR09MB485153B7CB706E188DED763484402@AM9PR09MB4851.eurprd09.prod.outlook.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Include CP0 MemoryMapID register in migration state.
Fixes: 99029be1c2 ("target/mips: Add implementation of GINVT instruction")
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Aleksandar Rakic <aleksandar.rakic@htecgroup.com>
Reviewed-by: Aleksandar Rikalo <arikalo@gmail.com>
Message-ID: <AM9PR09MB4851FB6034EDB7FA191BA47E84402@AM9PR09MB4851.eurprd09.prod.outlook.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
With pv steal time supported, VM machine needs get physical address
of each vcpu and notify new host during migration. Here two
functions kvm_get_stealtime/kvm_set_stealtime, and guest steal time
physical address is only updated on KVM_PUT_FULL_STATE stage.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240930064040.753929-1-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
When we run “qemu-system-loongarch64 -qmp stdio -vnc none -S”,
we get an error message “Need kernel filename” and then we can't use qmp cmd to query some information.
So, we just throw a warning and then the cpus starts running from address VIRT_FLASH0_BASE.
Signed-off-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20241030012359.4040817-1-gaosong@loongson.cn>
update linux-headers to v6.12-rc5. Pass to compile on aarch64, arm,
loongarch64, x86_64, i386, riscv64,riscv32 softmmu and linux-user.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Acked-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20241028023809.1554405-4-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
KVM LBT supports on LoongArch depends on the linux-header file
kvm_para.h, add header file kvm_para.h here.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Acked-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20241028023809.1554405-3-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
since 6.11, unistd.h includes header file unistd_64.h directly on
some platforms, here add unistd_64.h on these platforms. Affected
platforms are ARM64, LoongArch64 and Riscv. Otherwise there will
be compiling error such as:
linux-headers/asm/unistd.h:3:10: fatal error: asm/unistd_64.h: No such file or directory
#include <asm/unistd_64.h>
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Acked-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20241028023809.1554405-2-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Implement PMU extension for LoongArch kvm mode. Use OnOffAuto type
variable pmu to check the PMU feature. If the PMU Feature is not supported
with KVM host, it reports error if there is pmu=on command line.
If there is no any command line about pmu parameter, it checks whether
KVM host supports the PMU Feature and set the corresponding value in cpucfg.
This patch is based on lbt patch located at
https://lore.kernel.org/qemu-devel/20240904061859.86615-1-maobibo@loongson.cn
Co-developed-by: Song Gao <gaosong@loongson.cn>
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240918082315.2345034-1-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Six registers scr0 - scr3, eflags and ftop are added in percpu vmstate.
And two functions kvm_loongarch_get_lbt/kvm_loongarch_put_lbt are added
to save/restore lbt registers.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240929070405.235200-3-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Loongson Binary Translation (LBT) is used to accelerate binary
translation, which contains 4 scratch registers (scr0 to scr3), x86/ARM
eflags (eflags) and x87 fpu stack pointer (ftop).
Now LBT feature is added in kvm mode, not supported in TCG mode since
it is not emulated. Feature variable lbt is added with OnOffAuto type,
If lbt feature is not supported with KVM host, it reports error if there
is lbt=on command line.
If there is no any command line about lbt parameter, it checks whether
KVM host supports lbt feature and set the corresponding value in cpucfg.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240929070405.235200-2-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
This way there aren't stale flags there.
p->flags can't contain SYNC to be sent at the next RAM packet since syncs
are now handled separately in multifd_send_thread.
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Link: https://lore.kernel.org/r/1c96b6cdb797e6f035eb1a4ad9bfc24f4c7f5df8.1730203967.git.maciej.szmigiero@oracle.com
Signed-off-by: Peter Xu <peterx@redhat.com>
Now with the current migration_is_running(), it will report exactly the
opposite of what will be reported by migration_is_idle().
Drop migration_is_idle(), instead use "!migration_is_running()" which
should be identical on functionality.
In reality, most of the idle check is inverted, so it's even easier to
write with "migrate_is_running()" check.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Link: https://lore.kernel.org/r/20241024213056.1395400-6-peterx@redhat.com
Signed-off-by: Peter Xu <peterx@redhat.com>
This helper is mostly the same as migration_is_running(), except that one
has COLO reported as true, the other has CANCELLING reported as true.
Per my past years experience on the state changes, none of them should
matter.
To make it slightly safer, report both COLO || CANCELLING to be true in
migration_is_running(), then drop the other one. We kept the 1st only
because the name is simpler, and clear enough.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Link: https://lore.kernel.org/r/20241024213056.1395400-5-peterx@redhat.com
Signed-off-by: Peter Xu <peterx@redhat.com>
It's only used within migration/, so it shouldn't be exported.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Link: https://lore.kernel.org/r/20241024213056.1395400-3-peterx@redhat.com
Signed-off-by: Peter Xu <peterx@redhat.com>
Both migration thread or background snapshot thread will take a refcount of
the migration object at the entrace of the thread function.
That makes sense, because it protects the object from being freed by the
main thread in migration_shutdown() later, but it might still race with it
if the thread is scheduled too late. Consider the case right after
pthread_create() happened, VM shuts down with the object released, but
right after that the migration thread finally got created, referencing
MigrationState* in the opaque pointer which is already freed.
The only 100% safe way to make sure it won't get freed is taking the
refcount right before the thread is created, meanwhile when BQL is held.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Link: https://lore.kernel.org/r/20241024213056.1395400-2-peterx@redhat.com
Signed-off-by: Peter Xu <peterx@redhat.com>
Per previous discussion [1,2], this patch deprecates query-migrationthreads
command.
To summarize, the major reason of the deprecation is due to no sensible way
to consume the API properly:
(1) The reported list of threads are incomplete (ignoring destination
threads and non-multifd threads).
(2) For CPU pinning, there's no way to properly pin the threads with
the API if the threads will start running right away after migration
threads can be queried, so the threads will always run on the default
cores for a short window.
(3) For VM debugging, one can use "-name $VM,debug-threads=on" instead,
which will provide proper names for all migration threads.
[1] https://lore.kernel.org/r/20240930195837.825728-1-peterx@redhat.com
[2] https://lore.kernel.org/r/20241011153417.516715-1-peterx@redhat.com
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Acked-by: Markus Armbruster <armbru@redhat.com>
Link: https://lore.kernel.org/r/20241022194501.1022443-1-peterx@redhat.com
Signed-off-by: Peter Xu <peterx@redhat.com>
The linker on OpenBSD complains:
ld: warning: dirtyrate.c:447 (../src/migration/dirtyrate.c:447)(...):
warning: strcpy() is almost always misused, please use strlcpy()
It's currently not a real problem in this case since both arrays
have the same size (256 bytes). But just in case somebody changes
the size of the source array in the future, let's better play safe
and use g_strlcpy() here instead, with an additional check that the
string has been copied as a whole.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Hyman Huang <yong.huang@smartx.com>
Link: https://lore.kernel.org/r/20241022063402.184213-1-thuth@redhat.com
[peterx: Fix over-80 chars]
Signed-off-by: Peter Xu <peterx@redhat.com>
When VM is configured with huge memory, the current throttle logic
doesn't look like to scale, because migration_trigger_throttle()
is only called for each iteration, so it won't be invoked for a long
time if one iteration can take a long time.
The periodic dirty sync aims to fix the above issue by synchronizing
the ramblock from remote dirty bitmap and, when necessary, triggering
the CPU throttle multiple times during a long iteration.
This is a trade-off between synchronization overhead and CPU throttle
impact.
Signed-off-by: Hyman Huang <yong.huang@smartx.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Link: https://lore.kernel.org/r/f61f1b3653f2acf026901103e1c73d157d38b08f.1729146786.git.yong.huang@smartx.com
[peterx: make prev_cnt global, and reset for each migration]
Signed-off-by: Peter Xu <peterx@redhat.com>
The global static variable ram_state in fact is referred to by the
"rs" parameter in migration_bitmap_sync_precopy. For ease of calling
by the callees, use the global variable directly in
migration_bitmap_sync_precopy and remove "rs" parameter.
The migration_bitmap_sync_precopy will be exported in the next commit.
Signed-off-by: Hyman Huang <yong.huang@smartx.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Link: https://lore.kernel.org/r/283c335d61463bf477160da91b24da45cdaf3e43.1729146786.git.yong.huang@smartx.com
Signed-off-by: Peter Xu <peterx@redhat.com>
Move cpu-throttle.c from system to migration since it's
only used for migration; this makes us avoid exporting the
util functions and variables in misc.h but export them in
migration.h when implementing the periodic ramblock dirty
sync feature in the upcoming commits.
Since CPU throttle timers are only used in migration, move
their registry to migration_object_init.
Signed-off-by: Hyman Huang <yong.huang@smartx.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Link: https://lore.kernel.org/r/c1b3efaa0cb49e03d422e9da97bdb65cc3d234d1.1729146786.git.yong.huang@smartx.com
[peterx: Fix build on MacOS on cocoa.m, not move cpu-throttle.h yet]
[peterx: Fix subject spelling, per pm215]
Signed-off-by: Peter Xu <peterx@redhat.com>
migration/savevm.c contains some calls to vmstate_save() that are
followed by migrate_set_error() if the integer return value indicates an
error. migrate_set_error() requires that the `Error *` object passed to
it is set. Therefore, vmstate_save() is assumed to always set *errp on
error.
Right now, that assumption is not met: vmstate_save_state_v() (called
internally by vmstate_save()) will not set *errp if
vmstate_subsection_save() or vmsd->post_save() fail. Fix that by adding
an *errp parameter to vmstate_subsection_save(), and by generating a
generic error in case post_save() fails (as is already done for
pre_save()).
Without this patch, qemu will crash after vmstate_subsection_save() or
post_save() have failed inside of a vmstate_save() call (unless
migrate_set_error() then happen to discard the new error because
s->error is already set). This happens e.g. when receiving the state
from a virtio-fs back-end (virtiofsd) fails.
Signed-off-by: Hanna Czenczek <hreitz@redhat.com>
Link: https://lore.kernel.org/r/20241015170437.310358-1-hreitz@redhat.com
Signed-off-by: Peter Xu <peterx@redhat.com>
Keep migration thread names together, so it's easier to see a list of all
possible migration threads.
Still two functional changes below besides the macro defintions:
- There's one dirty rate thread that we overlooked before, now we add
that too and name it as "mig/dirtyrate" following the old rules.
- The old name "mig/src/rp-thr" has "-thr" but it may not be useful if
it's a thread name anyway, while "rp" can be slightly hard to read.
Taking this chance to rename it to "mig/src/return", hopefully a better
name.
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Acked-by: Hyman Huang <yong.huang@smartx.com>
Reviewed-by: Zhang Chen <chen.zhang@intel.com>
Link: https://lore.kernel.org/r/20241011153652.517440-1-peterx@redhat.com
Signed-off-by: Peter Xu <peterx@redhat.com>
The cleanup function can in many cases needs cleanup on its own.
The major thing we want to do here is not referencing to_dst_file when
without the file mutex. When at it, touch things elsewhere too to make it
look slightly better in general.
One thing to mention is, migration_thread has its own "running" boolean, so
it doesn't need to rely on to_dst_file being non-NULL. Multifd has a
dependency so it needs to be skipped if to_dst_file is not yet set; add a
richer comment for such reason.
Resolves: Coverity CID 1527402
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Link: https://lore.kernel.org/r/20240919163042.116767-1-peterx@redhat.com
Signed-off-by: Peter Xu <peterx@redhat.com>
AVX10 state enumeration in CPUID leaf D and enabling in XCR0 register
are identical to AVX512 state regardless of the supported vector lengths.
Given that some E-cores will support AVX10 but not support AVX512, add
AVX512 state components to guest when AVX10 is enabled.
Based on a patch by Tao Su <tao1.su@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Tested-by: Xuelian Guo <xuelian.guo@intel.com>
Signed-off-by: Tao Su <tao1.su@linux.intel.com>
Link: https://lore.kernel.org/r/20241031085233.425388-8-tao1.su@linux.intel.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since the highest supported vector length for a processor implies that
all lesser vector lengths are also supported, add the dependencies of
the supported vector lengths. If all vector lengths aren't supported,
clear AVX10 enable bit as well.
Note that the order of AVX10 related dependencies should be kept as:
CPUID_24_0_EBX_AVX10_128 -> CPUID_24_0_EBX_AVX10_256,
CPUID_24_0_EBX_AVX10_256 -> CPUID_24_0_EBX_AVX10_512,
CPUID_24_0_EBX_AVX10_VL_MASK -> CPUID_7_1_EDX_AVX10,
CPUID_7_1_EDX_AVX10 -> CPUID_24_0_EBX,
so that prevent user from setting weird CPUID combinations, e.g. 256-bits
and 512-bits are supported but 128-bits is not, no vector lengths are
supported but AVX10 enable bit is still set.
Since AVX10_128 will be reserved as 1, adding these dependencies has the
bonus that when user sets -cpu host,-avx10-128, CPUID_7_1_EDX_AVX10 and
CPUID_24_0_EBX will be disabled automatically.
Tested-by: Xuelian Guo <xuelian.guo@intel.com>
Signed-off-by: Tao Su <tao1.su@linux.intel.com>
Link: https://lore.kernel.org/r/20241028024512.156724-5-tao1.su@linux.intel.com
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Link: https://lore.kernel.org/r/20241031085233.425388-7-tao1.su@linux.intel.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
