Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230109140306.23161-4-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some SDHCI IP can be synthetized in various endianness:
https://github.com/u-boot/u-boot/blob/v2021.04/doc/README.fsl-esdhc
- CONFIG_SYS_FSL_ESDHC_BE
ESDHC IP is in big-endian mode. Accessing ESDHC registers can be
determined by ESDHC IP's endian mode or processor's endian mode.
Our current implementation is little-endian. In order to support
big endianness:
- Rename current MemoryRegionOps as sdhci_mmio_le_ops ('le')
- Add an 'endianness' property to SDHCIState (default little endian)
- Set the 'io_ops' field in realize() after checking the property
- Add the sdhci_mmio_be_ops (big-endian) MemoryRegionOps.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20221101222934.52444-3-philmd@linaro.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Trying to run U-Boot for Cubieboard (Allwinner A10) fails because it cannot
access SD card. The problem is that FIFO register in current
allwinner-sdhost implementation is at the address corresponding to
Allwinner H3, but not A10.
Linux kernel is not affected since Linux driver uses DMA access and does
not use FIFO register for reading/writing.
This patch adds new class parameter `is_sun4i` and based on that
parameter uses register at offset 0x100 either as FIFO register (if
sun4i) or as threshold register (if not sun4i; in this case register at
0x200 is FIFO register).
Tested with U-Boot and Linux kernel image built for Cubieboard and
OrangePi PC.
Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20221112214900.24152-1-strahinja.p.jankovic@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The device model's functions start with "usdhc_", so rename the defines
accordingly for consistency.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20221018210146.193159-5-shentey@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
These defines aren't used outside of sdhci.c, so can be defined there.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20221018210146.193159-4-shentey@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Swap 'buf' and 'bytes' around for consistency with
blk_co_{pread,pwrite}(), and in preparation to implement these functions
using generated_co_wrapper.
Callers were updated using this Coccinelle script:
@@ expression blk, offset, buf, bytes, flags; @@
- blk_pread(blk, offset, buf, bytes, flags)
+ blk_pread(blk, offset, bytes, buf, flags)
@@ expression blk, offset, buf, bytes, flags; @@
- blk_pwrite(blk, offset, buf, bytes, flags)
+ blk_pwrite(blk, offset, bytes, buf, flags)
It had no effect on hw/block/nand.c, presumably due to the #if, so that
file was updated manually.
Overly-long lines were then fixed by hand.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-4-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
For consistency with other I/O functions, and in preparation to
implement it using generated_co_wrapper.
Callers were updated using this Coccinelle script:
@@ expression blk, offset, buf, bytes; @@
- blk_pread(blk, offset, buf, bytes)
+ blk_pread(blk, offset, buf, bytes, 0)
It had no effect on hw/block/nand.c, presumably due to the #if, so that
file was updated manually.
Overly-long lines were then fixed by hand.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-3-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
U-Boot queries the FIFO water level to reduce checking status register
when doing PIO SD card operation.
Report a FIFO water level of 1 when data is ready, to prevent the code
from trying to read 0 words from the FIFO each time.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Message-id: 20220520124200.2112699-1-uwu@icenowy.me
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The issue reported by OSS-Fuzz produces the following backtrace:
==447470==ERROR: AddressSanitizer: heap-buffer-overflow
READ of size 1 at 0x61500002a080 thread T0
#0 0x71766d47 in sdhci_read_dataport hw/sd/sdhci.c:474:18
#1 0x7175f139 in sdhci_read hw/sd/sdhci.c:1022:19
#2 0x721b937b in memory_region_read_accessor softmmu/memory.c:440:11
#3 0x72171e51 in access_with_adjusted_size softmmu/memory.c:554:18
#4 0x7216f47c in memory_region_dispatch_read1 softmmu/memory.c:1424:16
#5 0x7216ebb9 in memory_region_dispatch_read softmmu/memory.c:1452:9
#6 0x7212db5d in flatview_read_continue softmmu/physmem.c:2879:23
#7 0x7212f958 in flatview_read softmmu/physmem.c:2921:12
#8 0x7212f418 in address_space_read_full softmmu/physmem.c:2934:18
#9 0x721305a9 in address_space_rw softmmu/physmem.c:2962:16
#10 0x7175a392 in dma_memory_rw_relaxed include/sysemu/dma.h:89:12
#11 0x7175a0ea in dma_memory_rw include/sysemu/dma.h:132:12
#12 0x71759684 in dma_memory_read include/sysemu/dma.h:152:12
#13 0x7175518c in sdhci_do_adma hw/sd/sdhci.c:823:27
#14 0x7174bf69 in sdhci_data_transfer hw/sd/sdhci.c:935:13
#15 0x7176aaa7 in sdhci_send_command hw/sd/sdhci.c:376:9
#16 0x717629ee in sdhci_write hw/sd/sdhci.c:1212:9
#17 0x72172513 in memory_region_write_accessor softmmu/memory.c:492:5
#18 0x72171e51 in access_with_adjusted_size softmmu/memory.c:554:18
#19 0x72170766 in memory_region_dispatch_write softmmu/memory.c:1504:16
#20 0x721419ee in flatview_write_continue softmmu/physmem.c:2812:23
#21 0x721301eb in flatview_write softmmu/physmem.c:2854:12
#22 0x7212fca8 in address_space_write softmmu/physmem.c:2950:18
#23 0x721d9a53 in qtest_process_command softmmu/qtest.c:727:9
A DMA descriptor is previously filled in RAM. An I/O access to the
device (frames #22 to #16) start the DMA engine (frame #13). The
engine fetch the descriptor and execute the request, which itself
accesses the SDHCI I/O registers (frame #1 and #0), triggering a
re-entrancy issue.
Fix by prohibit transactions from the DMA to devices. The DMA engine
is thus restricted to memories.
Reported-by: OSS-Fuzz (Issue 36391)
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/451
Message-Id: <20211215205656.488940-3-philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
DMA transactions might fail. The DMA API returns a MemTxResult,
indicating such failures. Do not ignore it. On failure, raise
the ADMA error flag and eventually triggering an IRQ (see spec
chapter 1.13.5: "ADMA2 States").
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20211215205656.488940-2-philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
More than 1k of TypeInfo instances are already marked as const. Mark the
remaining ones, too.
This commit was created with:
git grep -z -l 'static TypeInfo' -- '*.c' | \
xargs -0 sed -i 's/static TypeInfo/static const TypeInfo/'
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20220117145805.173070-2-shentey@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In SPI-mode, SD card's OCR register: Card Capacity Status (CCS) bit
is not set to 1 correclty when the assigned SD image size is larger
than 2GB (SDHC). This will cause the SD card to be indentified as SDSC
incorrectly. CCS bit should be set to 1 if we are using SDHC.
Also, as there's no power up emulation in SPI-mode.
The OCR register: Card power up status bit bit (busy) should also
be set to 1 when reset. (busy bit is set to LOW if the card has not
finished the power up routine.)
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20211228125719.14712-1-frank.chang@sifive.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
'wp_groups' holds a bitmap, rename it as 'wp_group_bmap'.
'wpgrps_size' is the bitmap size (in bits), rename it as
'wp_group_bits'.
Patch created mechanically using:
$ sed -i -e s/wp_groups/wp_group_bmap/ \
-e s/wpgrps_size/wp_group_bits/ hw/sd/sd.c
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210728181728.2012952-4-f4bug@amsat.org>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
ssi_sd_realize() creates an "sd-card" device. This is inappropriate,
and marked FIXME.
Move it to the boards that create these devices. Prior art: commit
eb4f566bbb for device "generic-sdhci", and commit 26c607b86b for
device "pl181".
The device remains not user-creatable, because its users should (and
do) wire up its GPIO chip-select line.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Cc: Bin Meng <bin.meng@windriver.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: "Philippe Mathieu-Daudé" <f4bug@amsat.org>
Cc: qemu-arm@nongnu.org
Cc: qemu-riscv@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-2-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-Id: <20211018132609.160008-6-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Rename qbus_create_inplace() to qbus_init(); this is more in line
with our usual naming convention for functions that in-place
initialize objects.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20210923121153.23754-5-peter.maydell@linaro.org
OSS-Fuzz found sending illegal addresses when querying the write
protection bits triggers the assertion added in commit 84816fb63e
("hw/sd/sdcard: Assert if accessing an illegal group"):
qemu-fuzz-i386-target-generic-fuzz-sdhci-v3: ../hw/sd/sd.c:824: uint32_t sd_wpbits(SDState *, uint64_t):
Assertion `wpnum < sd->wpgrps_size' failed.
#3 0x7f62a8b22c91 in __assert_fail
#4 0x5569adcec405 in sd_wpbits hw/sd/sd.c:824:9
#5 0x5569adce5f6d in sd_normal_command hw/sd/sd.c:1389:38
#6 0x5569adce3870 in sd_do_command hw/sd/sd.c:1737:17
#7 0x5569adcf1566 in sdbus_do_command hw/sd/core.c💯16
#8 0x5569adcfc192 in sdhci_send_command hw/sd/sdhci.c:337:12
#9 0x5569adcfa3a3 in sdhci_write hw/sd/sdhci.c:1186:9
#10 0x5569adfb3447 in memory_region_write_accessor softmmu/memory.c:492:5
It is legal for the CMD30 to query for out-of-range addresses.
Such invalid addresses are simply ignored in the response (write
protection bits set to 0).
In commit 84816fb63e ("hw/sd/sdcard: Assert if accessing an illegal
group") we misplaced the assertion *before* we test the address is
in range. Move it *after*.
Include the qtest reproducer provided by Alexander Bulekov:
$ make check-qtest-i386
...
Running test qtest-i386/fuzz-sdcard-test
qemu-system-i386: ../hw/sd/sd.c:824: sd_wpbits: Assertion `wpnum < sd->wpgrps_size' failed.
Cc: qemu-stable@nongnu.org
Reported-by: OSS-Fuzz (Issue 29225)
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Fixes: 84816fb63e ("hw/sd/sdcard: Assert if accessing an illegal group")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/495
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210802235524.3417739-3-f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Per the 'Physical Layer Simplified Specification Version 3.01',
Table 4-22: 'Block Oriented Write Protection Commands'
SEND_WRITE_PROT (CMD30)
If the card provides write protection features, this command asks
the card to send the status of the write protection bits [1].
[1] 32 write protection bits (representing 32 write protect groups
starting at the specified address) [...]
The last (least significant) bit of the protection bits corresponds
to the first addressed group. If the addresses of the last groups
are outside the valid range, then the corresponding write protection
bits shall be set to 0.
Split the if() statement (without changing the behaviour of the code)
to better position the description comment.
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210802235524.3417739-2-f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
OSS-Fuzz found sending illegal addresses when querying the write
protection bits triggers an assertion:
qemu-fuzz-i386: hw/sd/sd.c:824: uint32_t sd_wpbits(SDState *, uint64_t): Assertion `wpnum < sd->wpgrps_size' failed.
==11578== ERROR: libFuzzer: deadly signal
#8 0x7ffff628e091 in __assert_fail
#9 0x5555588f1a3c in sd_wpbits hw/sd/sd.c:824:9
#10 0x5555588dd271 in sd_normal_command hw/sd/sd.c:1383:38
#11 0x5555588d777c in sd_do_command hw/sd/sd.c
#12 0x555558cb25a0 in sdbus_do_command hw/sd/core.c💯16
#13 0x555558e02a9a in sdhci_send_command hw/sd/sdhci.c:337:12
#14 0x555558dffa46 in sdhci_write hw/sd/sdhci.c:1187:9
#15 0x5555598b9d76 in memory_region_write_accessor softmmu/memory.c:489:5
Similarly to commit 8573378e62 ("hw/sd: fix out-of-bounds check
for multi block reads"), check the address range before sending
the status of the write protection bits.
Include the qtest reproducer provided by Alexander Bulekov:
$ make check-qtest-i386
...
Running test qtest-i386/fuzz-sdcard-test
qemu-system-i386: ../hw/sd/sd.c:824: sd_wpbits: Assertion `wpnum < sd->wpgrps_size' failed.
Reported-by: OSS-Fuzz (Issue 29225)
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/450
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20210702155900.148665-4-f4bug@amsat.org>
Multiple commands have to check the address requested is valid.
Extract this code pattern as a new address_in_range() helper, and
log invalid accesses as guest errors.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210624142209.1193073-3-f4bug@amsat.org>
We report the card is in an inconsistent state, but don't precise
in which state it is. Add this information, as it is useful when
debugging problems.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210624142209.1193073-2-f4bug@amsat.org>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Commit e50caf4a5c ("tracing: convert documentation to rST")
converted docs/devel/tracing.txt to docs/devel/tracing.rst.
We still have several references to the old file, so let's fix them
with the following command:
sed -i s/tracing.txt/tracing.rst/ $(git grep -l docs/devel/tracing.txt)
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210517151702.109066-2-sgarzare@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Target lm32 was deprecated in commit d849800512, v5.2.0. See there
for rationale.
Some of its code lives on in device models derived from milkymist
ones: hw/char/digic-uart.c and hw/display/bcm2835_fb.c.
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210503084034.3804963-2-armbru@redhat.com>
Acked-by: Michael Walle <michael@walle.cc>
[Trivial conflicts resolved, reST markup fixed]
The omap_mmc_reset() function resets its SD card via
device_legacy_reset(). We know that the SD card does not have a qbus
of its own, so the new device_cold_reset() function (which resets
both the device and its child buses) is equivalent here to
device_legacy_reset() and we can just switch to the new API.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210430222348.8514-1-peter.maydell@linaro.org
Many files include qemu/log.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210328054833.2351597-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Many files include hw/irq.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210327050236.2232347-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
If the block size is programmed to a different value from the
previous one, reset the data pointer of s->fifo_buffer[] so that
s->fifo_buffer[] can be filled in using the new block size in
the next transfer.
With this fix, the following reproducer:
outl 0xcf8 0x80001010
outl 0xcfc 0xe0000000
outl 0xcf8 0x80001001
outl 0xcfc 0x06000000
write 0xe000002c 0x1 0x05
write 0xe0000005 0x1 0x02
write 0xe0000007 0x1 0x01
write 0xe0000028 0x1 0x10
write 0x0 0x1 0x23
write 0x2 0x1 0x08
write 0xe000000c 0x1 0x01
write 0xe000000e 0x1 0x20
write 0xe000000f 0x1 0x00
write 0xe000000c 0x1 0x32
write 0xe0000004 0x2 0x0200
write 0xe0000028 0x1 0x00
write 0xe0000003 0x1 0x40
cannot be reproduced with the following QEMU command line:
$ qemu-system-x86_64 -nographic -machine accel=qtest -m 512M \
-nodefaults -device sdhci-pci,sd-spec-version=3 \
-drive if=sd,index=0,file=null-co://,format=raw,id=mydrive \
-device sd-card,drive=mydrive -qtest stdio
Cc: qemu-stable@nongnu.org
Fixes: CVE-2020-17380
Fixes: CVE-2020-25085
Fixes: CVE-2021-3409
Fixes: d7dfca0807 ("hw/sdhci: introduce standard SD host controller")
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Reported-by: Cornelius Aschermann (Ruhr-Universität Bochum)
Reported-by: Sergej Schumilo (Ruhr-Universität Bochum)
Reported-by: Simon Wörner (Ruhr-Universität Bochum)
Buglink: https://bugs.launchpad.net/qemu/+bug/1892960
Buglink: https://bugs.launchpad.net/qemu/+bug/1909418
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1928146
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210303122639.20004-6-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The codes to limit the maximum block size is only necessary when
SDHC_BLKSIZE register is writable.
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210303122639.20004-5-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
When an ADMA transfer is started, the codes forget to set the
controller status to indicate a transfer is in progress.
With this fix, the following 2 reproducers:
https://paste.debian.net/plain/1185136https://paste.debian.net/plain/1185141
cannot be reproduced with the following QEMU command line:
$ qemu-system-x86_64 -nographic -machine accel=qtest -m 512M \
-nodefaults -device sdhci-pci,sd-spec-version=3 \
-drive if=sd,index=0,file=null-co://,format=raw,id=mydrive \
-device sd-card,drive=mydrive -qtest stdio
Cc: qemu-stable@nongnu.org
Fixes: CVE-2020-17380
Fixes: CVE-2020-25085
Fixes: CVE-2021-3409
Fixes: d7dfca0807 ("hw/sdhci: introduce standard SD host controller")
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Reported-by: Cornelius Aschermann (Ruhr-Universität Bochum)
Reported-by: Sergej Schumilo (Ruhr-Universität Bochum)
Reported-by: Simon Wörner (Ruhr-Universität Bochum)
Buglink: https://bugs.launchpad.net/qemu/+bug/1892960
Buglink: https://bugs.launchpad.net/qemu/+bug/1909418
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1928146
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210303122639.20004-4-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
At the end of sdhci_send_command(), it starts a data transfer if the
command register indicates data is associated. But the data transfer
should only be initiated when the command execution has succeeded.
With this fix, the following reproducer:
outl 0xcf8 0x80001810
outl 0xcfc 0xe1068000
outl 0xcf8 0x80001804
outw 0xcfc 0x7
write 0xe106802c 0x1 0x0f
write 0xe1068004 0xc 0x2801d10101fffffbff28a384
write 0xe106800c 0x1f 0x9dacbbcad9e8f7061524334251606f7e8d9cabbac9d8e7f60514233241505f
write 0xe1068003 0x28 0x80d000251480d000252280d000253080d000253e80d000254c80d000255a80d000256880d0002576
write 0xe1068003 0x1 0xfe
cannot be reproduced with the following QEMU command line:
$ qemu-system-x86_64 -nographic -M pc-q35-5.0 \
-device sdhci-pci,sd-spec-version=3 \
-drive if=sd,index=0,file=null-co://,format=raw,id=mydrive \
-device sd-card,drive=mydrive \
-monitor none -serial none -qtest stdio
Cc: qemu-stable@nongnu.org
Fixes: CVE-2020-17380
Fixes: CVE-2020-25085
Fixes: CVE-2021-3409
Fixes: d7dfca0807 ("hw/sdhci: introduce standard SD host controller")
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Reported-by: Cornelius Aschermann (Ruhr-Universität Bochum)
Reported-by: Sergej Schumilo (Ruhr-Universität Bochum)
Reported-by: Simon Wörner (Ruhr-Universität Bochum)
Buglink: https://bugs.launchpad.net/qemu/+bug/1892960
Buglink: https://bugs.launchpad.net/qemu/+bug/1909418
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1928146
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210303122639.20004-2-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
At present the sd_erase() does not erase the requested range of card
data to 0xFFs. Let's make the erase operation actually happen.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <1613811493-58815-1-git-send-email-bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
"qemu-common.h" should be included to provide the forward declaration
of qemu_hexdump() when DEBUG_SD is on.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210228050609.24779-1-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
-----BEGIN PGP SIGNATURE-----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=ipHI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/vivier2/tags/trivial-branch-for-6.0-pull-request' into staging
Pull request trivial patches 20210220
# gpg: Signature made Sat 20 Feb 2021 12:34:21 GMT
# gpg: using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg: issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier2/tags/trivial-branch-for-6.0-pull-request:
MAINTAINERS: Fix default-configs/ entries
target/avr/cpu: Use device_class_set_parent_realize()
hw/scsi/megasas: Remove pointless parenthesis
u2f-passthru: put it into the 'misc' category
tpm: put some tpm devices into the correct category
nvdimm: put it into the 'storage' category
vmmouse: put it into the 'input' category
virtio-pmem: put it into the 'storage' category
MAINTAINERS: add my github tree URL
Fix SPDX-License-Identifier typos
hw/block/fdc: Remove the check_media_rate property
hw/i386/xen: Remove dead code
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Several SPDX headers contain "SPDX-License-Identifer" (note the
missing "i" before "er"); fix these typos.
Signed-off-by: Ryan Finnie <ryan@finnie.org>
Cc: qemu-trivial@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210201200147.211914-1-ryan@finnie.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
s->prnsts is updated in both branches of the if () else () statement.
Move the common bits outside so that it is cleaner.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1613447214-81951-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Unlike SD mode, when SD card is working in SPI mode, the argument
of CMD13 is stuff bits. Hence we should bypass the RCA check.
See "Physical Layer Specification Version 8.00", chapter 7.3.1.3
Detailed Command Description (SPI mode):
"The card shall ignore stuff bits and reserved bits in an argument"
and Table 7-3 Commands and Arguments (SPI mode):
"CMD13 Argument [31:0] stuff bits"
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-9-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
High capacity cards don't support write protection hence we should
not perform the write protect groups check in CMD24/25 for them.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-8-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
High capacity cards don't support write protection hence we should
not perform the write protect groups check in sd_erase() for them.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-6-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
These APIs and macros may be referenced by functions that are
currently before them. Move them ahead a little bit.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-5-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per the "Physical Layer Specification Version 8.00", table 4-26
(SD mode) and table 7-3 (SPI mode) command descriptions, CMD30
response type is R1, not R1b.
Fixes: a1bb27b1e9 ("SD card emulation initial implementation")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-4-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per the "Physical Layer Specification Version 8.00", table 4-26
(SD mode) and table 7-3 (SPI mode) command descriptions, the
following commands:
- CMD28 (SET_WRITE_PROT)
- CMD29 (CLR_WRITE_PROT)
- CMD30 (SEND_WRITE_PROT)
are only supported by SDSC cards.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-3-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
For high capacity memory cards, the erase start address and end
address are multiplied by 512, but the address check is still
based on the original block number in sd->erase_{start, end}.
Fixes: 1bd6fd8ed5 ("hw/sd/sdcard: Do not attempt to erase out of range addresses")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-2-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Besides CMD12, the following command's reponse type is R1b:
- SET_WRITE_PROT (CMD28)
- CLR_WRITE_PROT (CMD29)
- ERASE (CMD38)
Reuse the same s->stopping to indicate a R1b reponse is needed.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210128063035.15674-10-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
CMD12's response type is R1b, which is basically a R1 plus optional
addition of the busy signal token that can be any number of bytes.
A zero value indicates card is busy and a non-zero value indicates
the card is ready for the next command.
Current implementation sends the busy signal token without sending
the R1 first. This does not break the U-Boot/Linux mmc_spi driver,
but it does not make the VxWorks driver happy.
Move the testing logic of s->stopping in the SSI_SD_RESPONSE state
a bit later, after the first byte of the card reponse is sent out,
to conform with the spec. After the busy signal token is sent, the
state should be transferred to SSI_SD_CMD.
Fixes: 775616c3ae ("Partial SD card SPI mode support")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20210128063035.15674-9-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The SEND_IF_COND command (CMD8) response is of format R7, but
current code returns R1 for CMD8. Fix it.
Fixes: 775616c3ae ("Partial SD card SPI mode support")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210128063035.15674-8-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
For a multiple block write operation, each block begins with a multi
write start token. Unlike the SD mode that the multiple block write
ends when receiving a STOP_TRAN command (CMD12), a special stop tran
token is used to signal the card.
Emulating this by manually sending a CMD12 to the SD card core, to
bring it out of the receiving data state.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-7-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Add 2 more states for the block write operation. The SPI host needs
to send a data start token to start the transfer, and the data block
written to the card will be acknowledged by a data response token.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
[PMD: Change VMState version id 6 -> 7]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-6-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
At present there is a data_ready() callback for the SD data read
path. Let's add a receive_ready() for the SD data write path.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-5-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
At present the single/multiple block write in SPI mode is blocked
by sd_normal_command(). Remove the limitation.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210128063035.15674-4-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The single block read (CMD17) codes are the same as the multiple
block read (CMD18). Merge them into one. The same applies to single
block write (CMD24) and multiple block write (CMD25).
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-3-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
In the case of a multiple block read operation every transferred
block has its suffix of CRC16. Update the state machine logic to
handle multiple block read.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
[PMD: Change VMState version id 5 -> 6]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-2-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Currently, blk_is_read_only() tells whether a given BlockBackend can
only be used in read-only mode because its root node is read-only. Some
callers actually try to answer a slightly different question: Is the
BlockBackend configured to be writable, by taking write permissions on
the root node?
This can differ, for example, for CD-ROM devices which don't take write
permissions, but may be backed by a writable image file. scsi-cd allows
write requests to the drive if blk_is_read_only() returns false.
However, the write request will immediately run into an assertion
failure because the write permission is missing.
This patch introduces separate functions for both questions.
blk_supports_write_perm() answers the question whether the block
node/image file can support writable devices, whereas blk_is_writable()
tells whether the BlockBackend is currently configured to be writable.
All calls of blk_is_read_only() are converted to one of the two new
functions.
Fixes: https://bugs.launchpad.net/bugs/1906693
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210118123448.307825-2-kwolf@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
At present the codes use hardcoded numbers (0xff/0xfe) for the dummy
value and block start token. Replace them with macros.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-12-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This fixes the wrong command index for STOP_TRANSMISSION, the
required command to interrupt the multiple block read command,
in the old codes. It should be CMD12 (0x4c), not CMD13 (0x4d).
Fixes: 775616c3ae ("Partial SD card SPI mode support")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-10-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per the "Physical Layer Specification Version 8.00" chapter 7.5.2,
"Data Read", there is a minimum 8 clock cycles (Nac) after the card
response and before data block shows up on the data out line. This
applies to both single and multiple block read operations.
Current implementation of single block read already satisfies the
timing requirement as in the RESPONSE state after all responses are
transferred the state remains unchanged. In the next 8 clock cycles
it jumps to DATA_START state if data is ready.
However we need an explicit state when expanding our support to
multiple block read in the future. Let's add a new state PREP_DATA
explicitly in the ssi-sd state machine to represent Nac.
Note we don't change the single block read state machine to let it
jump from RESPONSE state to DATA_START state as that effectively
generates a 16 clock cycles Nac, which might not be safe. As the
spec says the maximum Nac shall be calculated from several fields
encoded in the CSD register, we don't want to bother updating CSD
to ensure our Nac is within range to complicate things.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-9-bmeng.cn@gmail.com>
[PMD: Change VMState version id 4 -> 5]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per the SD spec, a valid data block is suffixed with a 16-bit CRC
generated by the standard CCITT polynomial x16+x12+x5+1. This part
is currently missing in the ssi-sd state machine. Without it, all
data block transfer fails in guest software because the expected
CRC16 is missing on the data out line.
Fixes: 775616c3ae ("Partial SD card SPI mode support")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-8-bmeng.cn@gmail.com>
[PMD: Change VMState version id 3 -> 4,
check s->mode validity in post_load()]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
commit f6fb1f9b31 ("sdcard: Correct CRC16 offset in sd_function_switch()")
changed the 16-bit CRC to be stored at offset 64. In fact, this CRC
calculation is completely wrong. From the original codes, it wants
to calculate the CRC16 of the first 64 bytes of sd->data[], however
passing 64 as the `width` to sd_crc16() actually counts 256 bytes
starting from the `message` for the CRC16 calculation, which is not
what we want.
Besides that, it seems existing sd_crc16() algorithm does not match
the SD spec, which says CRC16 is the CCITT one but the calculation
does not produce expected result. It turns out the CRC16 was never
transferred outside the sd core, as in sd_read_byte() we see:
if (sd->data_offset >= 64)
sd->state = sd_transfer_state;
Given above reasons, let's drop it.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-6-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
After the card is put into SPI mode, CRC check for all commands
including CMD0 will be done according to CMD59 setting. But this
command is currently unimplemented. Simply allow the decoding of
CMD59, but the CRC remains unchecked.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-5-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per the "Physical Layer Specification Version 8.00" chapter 7.5.1,
"Command/Response", there is a minimum 8 clock cycles (Ncr) before
the card response shows up on the data out line. However current
implementation jumps directly to the sending response state after
all 6 bytes command is received, which is a spec violation.
Add a new state PREP_RESP in the ssi-sd state machine to handle it.
Fixes: 775616c3ae ("Partial SD card SPI mode support")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-4-bmeng.cn@gmail.com>
[PMD: Change VMState version id 2 -> 3]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This commit is the result of running the timer-del-timer-free.cocci
script on the whole source tree.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201215154107.3255-4-peter.maydell@linaro.org
Move the property types and property macros implemented in
qdev-properties-system.c to a new qdev-properties-system.h
header.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-16-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
In order to use inclusive terminology, rename SSI 'slave' as
'peripheral', following the specification resolution:
https://www.oshwa.org/a-resolution-to-redefine-spi-signal-names/
Patch created mechanically using:
$ sed -i s/SSISlave/SSIPeripheral/ $(git grep -l SSISlave)
$ sed -i s/SSI_SLAVE/SSI_PERIPHERAL/ $(git grep -l SSI_SLAVE)
$ sed -i s/ssi-slave/ssi-peripheral/ $(git grep -l ssi-slave)
$ sed -i s/ssi_slave/ssi_peripheral/ $(git grep -l ssi_slave)
$ sed -i s/ssi_create_slave/ssi_create_peripheral/ \
$(git grep -l ssi_create_slave)
Then in VMStateDescription vmstate_ssi_peripheral we restored
the "SSISlave" migration stream name (to avoid breaking migration).
Finally the following files have been manually tweaked:
- hw/ssi/pl022.c
- hw/ssi/xilinx_spips.c
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201012124955.3409127-4-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Per the SD spec, to indicate a 2 GiB card, BLOCK_LEN shall be 1024
bytes, hence the READ_BL_LEN field in the CSD register shall be 10
instead of 9.
This fixes the acceptance test error for the NetBSD 9.0 test of the
Orange Pi PC that has an expanded SD card image of 2 GiB size.
Fixes: 6d2d4069c4 ("hw/sd: Correct the maximum size of a Standard Capacity SD Memory Card")
Reported-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-Id: <20201025152357.11865-1-bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
This patch contains all the files, whose maintainer I could not get
from ‘get_maintainer.pl’ script.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023124424.20177-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Adapted exec.c and qdev-monitor.c to new location]
Signed-off-by: Thomas Huth <thuth@redhat.com>
The function selection fields (399:376) should be zeroed out to
prevent leftover from being or'ed into the switch function status
data structure.
This fixes the boot failure as seen in the acceptance testing on
the orangepi target.
Fixes: b638627c72 ("hw/sd: Fix incorrect populated function switch status data structure")
Reported-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201024014954.21330-1-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
I/O request length can not be negative.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200630133912.9428-15-f4bug@amsat.org>
CRC functions don't modify the buffer argument,
make it const.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200630133912.9428-14-f4bug@amsat.org>
cmd_valid_while_locked() only needs to read SDRequest->cmd,
pass it directly and make it const.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200630133912.9428-13-f4bug@amsat.org>
Add more descriptive comments to keep a clear separation
between static property vs runtime changeable.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200630133912.9428-12-f4bug@amsat.org>
We can not have more group than 'wpgrps_size'.
Assert if we are accessing a group above this limit.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201015063824.212980-7-f4bug@amsat.org>
While the Spec v3 is not very clear, v6 states:
If the host provides an out of range address as an argument
to CMD32 or CMD33, the card shall indicate OUT_OF_RANGE error
in R1 (ERX) for CMD38.
If an address is out of range, do not attempt to erase it:
return R1 with the error bit set.
Buglink: https://bugs.launchpad.net/qemu/+bug/1895310
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201015063824.212980-6-f4bug@amsat.org>
From the Spec "4.3.5 Erase":
The host should adhere to the following command
sequence: ERASE_WR_BLK_START, ERASE_WR_BLK_END and
ERASE (CMD38).
If an erase (CMD38) or address setting (CMD32, 33)
command is received out of sequence, the card shall
set the ERASE_SEQ_ERROR bit in the status register
and reset the whole sequence.
Reset both addresses if the ERASE command occured
out of sequence (one of the start/end address is
not set).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201015063824.212980-5-f4bug@amsat.org>
As it is legal to WRITE/ERASE the address/block 0,
change the value of this definition to an illegal
address: UINT32_MAX.
Unfortunately this break the migration stream, so
bump the VMState version number. This affects some
ARM boards and the SDHCI_PCI device (which is only
used for testing).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201015063824.212980-4-f4bug@amsat.org>
'0' is used as a value to indicate an invalid (or unset)
address. Use a definition instead of a magic value.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201015063824.212980-3-f4bug@amsat.org>
Trace addresses provided to the ERASE command.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201015063824.212980-2-f4bug@amsat.org>
The Descriptor Table has a bit to allow the DMA to generates
Interrupt when the operation of the descriptor line is completed
(see "1.13.4. Descriptor Table" of 'SD Host Controller Simplified
Specification Version 2.00').
If we have pending interrupt and the descriptor requires it
to be generated as soon as it is completed, reschedule pending
transfers and yield to the CPU.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20200903172806.489710-5-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20200903172806.489710-4-f4bug@amsat.org>
If we have pending DMA requests scheduled, process them first.
So far we don't need to implement a bottom half to process them.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20200903172806.489710-3-f4bug@amsat.org>
Add datasheet name in the file header.
We can not add the direct download link since there is a disclaimers
to agree first on the SD Association website (www.sdcard.org).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20200901140411.112150-3-f4bug@amsat.org>
Add missing newline character in qemu_log_mask() format.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20200901140411.112150-2-f4bug@amsat.org>
Check if an address is free on the bus before plugging in the
device. This makes it possible to do the check without any
side effects, and to detect the problem early without having
to do it in the realize callback.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20201006123904.610658-5-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Fixes a bug in printing trap causes
- Allows 16-bit writes to the SiFive test device. This fixes the
failure to reboot the RISC-V virt machine
- Support for the Microchip PolarFire SoC and Icicle Kit
- A reafactor of RISC-V code out of hw/riscv
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAl9aa4YACgkQIeENKd+X
cFTJjgf5ASfFIO5HqP1l80/UM5Pswyq0IROZDq0ItZa6U4EPzLXoE2N0POriIj4h
Ds2JbMg0ORDqY0VbSxHlgYHMgJ9S6cuVOMnATsPG0d2jaJ3gSxLBu5k/1ENqe+Vw
sSYXZv5uEAUfOFz99zbuhKHct5HzlmBFW9dVHdflUQS+cRgsSXq27mz1BvZ8xMWl
lMhwubqdoNx0rOD3vKnlwrxaf54DcJ2IQT3BtTCjEar3tukdNaLijAuwt2hrFyr+
IwpeFXA/NWar+mXP3M+BvcLaI33j73/ac2+S5SJuzHGp/ot5nT5gAuq3PDEjHMeS
t6z9Exp776VXxNE2iUA5NB65Yp3/6w==
=07oA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20200910' into staging
This PR includes multiple fixes and features for RISC-V:
- Fixes a bug in printing trap causes
- Allows 16-bit writes to the SiFive test device. This fixes the
failure to reboot the RISC-V virt machine
- Support for the Microchip PolarFire SoC and Icicle Kit
- A reafactor of RISC-V code out of hw/riscv
# gpg: Signature made Thu 10 Sep 2020 19:08:06 BST
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20200910: (30 commits)
hw/riscv: Sort the Kconfig options in alphabetical order
hw/riscv: Drop CONFIG_SIFIVE
hw/riscv: Always build riscv_hart.c
hw/riscv: Move sifive_test model to hw/misc
hw/riscv: Move sifive_uart model to hw/char
hw/riscv: Move riscv_htif model to hw/char
hw/riscv: Move sifive_plic model to hw/intc
hw/riscv: Move sifive_clint model to hw/intc
hw/riscv: Move sifive_gpio model to hw/gpio
hw/riscv: Move sifive_u_otp model to hw/misc
hw/riscv: Move sifive_u_prci model to hw/misc
hw/riscv: Move sifive_e_prci model to hw/misc
hw/riscv: sifive_u: Connect a DMA controller
hw/riscv: clint: Avoid using hard-coded timebase frequency
hw/riscv: microchip_pfsoc: Hook GPIO controllers
hw/riscv: microchip_pfsoc: Connect 2 Cadence GEMs
hw/arm: xlnx: Set all boards' GEM 'phy-addr' property value to 23
hw/net: cadence_gem: Add a new 'phy-addr' property
hw/riscv: microchip_pfsoc: Connect a DMA controller
hw/dma: Add SiFive platform DMA controller emulation
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/riscv/trace-events
qemu_hexdump()'s pointer to the buffer and length of the
buffer are closely related arguments but are widely separated
in the argument list order (also, the format of <stdio.h>
function prototypes is usually to have the FILE* argument
coming first).
Reorder the arguments as "fp, prefix, buf, size" which is
more logical.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20200822180950.1343963-3-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Most uses of qemu_hexdump() do not take an array of char
as input, forcing use of cast. Since we can use this
helper to dump any kind of buffer, use a pointer to void
argument instead.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20200822180950.1343963-2-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Cadence SD/SDIO/eMMC Host Controller (SD4HC) is an SDHCI compatible
controller. The SDHCI compatible registers start from offset 0x200,
which are called Slot Register Set (SRS) in its datasheet.
This creates a Cadence SDHCI model built on top of the existing
generic SDHCI model. Cadence specific Host Register Set (HRS) is
implemented to make guest software happy.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-8-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Separate run of the TypeCheckMacro converter using the --force
flag, for the cases where typedefs weren't found in the same
header nor in typedefs.h.
Generated initially using:
$ ./scripts/codeconverter/converter.py --force -i \
--pattern=TypeCheckMacro $(git grep -l '' -- '*.[ch]')
Then each case was manually reviewed, and a comment was added
indicating what's unusual about those type checking
macros/functions. Despite not following the usual pattern, the
changes in this patch were found to be safe.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200831210740.126168-15-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
BIT(0) of the ASPEED_SDHCI_INFO register is set by SW and polled until
the bit is cleared by HW.
Use the number of supported slots to define the default value of this
register (The AST2600 eMMC Controller only has one). Fix the reset
sequence by clearing automatically the RESET bit.
Cc: Eddie James <eajames@linux.ibm.com>
Fixes: 2bea128c3d ("hw/sd/aspeed_sdhci: New device")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20200819100956.2216690-9-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Allow the device to execute the DMA transfers in a different
AddressSpace.
The A10 and H3 SoC keep using the system_memory address space,
but via the proper dma_memory_access() API.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20200814110057.307-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-40-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Per the SD spec, Standard Capacity SD Memory Card (SDSC) supports
capacity up to and including 2 GiB.
Fixes: 2d7adea4fe ("hw/sd: Support SDHC size cards")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Message-Id: <1598021136-49525-2-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
At present the function switch status data structure bit [399:376]
are wrongly pupulated. These 3 bytes encode function switch status
for the 6 function groups, with 4 bits per group, starting from
function group 6 at bit 399, then followed by function group 5 at
bit 395, and so on.
However the codes mistakenly fills in the function group 1 status
at bit 399. This fixes the code logic.
Fixes: a1bb27b1e9 ("SD card emulation (initial implementation)")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Message-Id: <1598021136-49525-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Use the recently added sdbus_read_data() to read multiple
bytes at once, instead of looping calling sdbus_read_byte().
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200814092346.21825-8-f4bug@amsat.org>
Add a sdbus_read_data() method to read multiple bytes on the
data line of a SD bus.
We might improve the tracing later, for now keep logging each
byte individually.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200814092346.21825-7-f4bug@amsat.org>
Use the recently added sdbus_write_data() to write multiple
bytes at once, instead of looping calling sdbus_write_byte().
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200814092346.21825-6-f4bug@amsat.org>
Add a sdbus_write_data() method to write multiple bytes on the
data line of a SD bus.
We might improve the tracing later, for now keep logging each
byte individually.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200814092346.21825-5-f4bug@amsat.org>
The sdbus_read_data() method do a single byte access on the data
line of a SD bus. Rename it as sdbus_read_byte() and document it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200814092346.21825-4-f4bug@amsat.org>
The sdbus_write_data() method do a single byte access on the data
line of a SD bus. Rename it as sdbus_write_byte() and document it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200814092346.21825-3-f4bug@amsat.org>
The read/write_data() methods write do a single byte access
on the data line of a SD card. Rename them as read/write_byte().
Add some documentation (not in "hw/sd/sdcard_legacy.h" which we
are going to remove soon).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200814092346.21825-2-f4bug@amsat.org>
omap_mmc.c is the last device left using the legacy sdcard API.
Move the prototype declarations into a separate header, to
make it clear this is a legacy API.
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <20180216022933.10945-8-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
sd_data_ready() belongs to the legacy API. As its last user has
been converted to the SDBus API, make it static.
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <20180216022933.10945-7-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Convert disabled DPRINTF() to trace events and remove ifdef'ry.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20200705204630.4133-9-f4bug@amsat.org>
SD/MMC host controllers provide a SD Bus to plug SD cards,
but don't come with SD card plugged in :) Let the machine/board
model create and plug the SD cards when required.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20200705204630.4133-8-f4bug@amsat.org>
Convert the controller to the SDBus API:
- add the a TYPE_PL181_BUS object of type TYPE_SD_BUS,
- adapt the SDBusClass set_inserted/set_readonly handlers
- create the bus in the PL181 controller
- switch legacy sd_*() API to the sdbus_*() API.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20200705204630.4133-7-f4bug@amsat.org>
To make the code easier to manage/review/use, rename the
cardstatus[0] variable as 'card_readonly' and name the GPIO
"card-read-only".
Similarly with cardstatus[1], renamed as 'card_inserted' and
name its GPIO "card-inserted".
Adapt the users accordingly by using the qdev_init_gpio_out_named()
function.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20200705204630.4133-6-f4bug@amsat.org>
Add TODO to use Fifo32 API from "qemu/fifo32.h".
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20200705204630.4133-4-f4bug@amsat.org>
pl181_send_command() do a bus transaction (send or receive),
rename it as pl181_do_command().
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20200705204630.4133-3-f4bug@amsat.org>
Replace a large number of the fprintf(stderr, "*\n" calls with
error_report(). The functions were renamed with these commands and then
compiler issues where manually fixed.
find ./* -type f -exec sed -i \
'N;N;N;N;N;N;N;N;N;N;N;N; {s|fprintf(stderr, "\(.*\)\\n"\(.*\));|error_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N;N;N;N;N;N;N;N; {s|fprintf(stderr, "\(.*\)\\n"\(.*\));|error_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N;N;N;N;N;N; {s|fprintf(stderr, "\(.*\)\\n"\(.*\));|error_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N;N;N;N;N; {s|fprintf(stderr, "\(.*\)\\n"\(.*\));|error_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N;N;N;N; {s|fprintf(stderr, "\(.*\)\\n"\(.*\));|error_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N;N;N; {s|fprintf(stderr, "\(.*\)\\n"\(.*\));|error_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N;N; {s|fprintf(stderr, "\(.*\)\\n"\(.*\));|error_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N; {s|fprintf(stderr, "\(.*\)\\n"\(.*\));|error_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N; {s|fprintf(stderr, "\(.*\)\\n"\(.*\));|error_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N; {s|fprintf(stderr, "\(.*\)\\n"\(.*\));|error_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N; {s|fprintf(stderr, "\(.*\)\\n"\(.*\));|error_report("\1"\2);|Ig}' \
{} +
Some lines where then manually tweaked to pass checkpatch.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <488ba8d4c562ea44119de8ea0f385a898bd8fa1e.1513790495.git.alistair.francis@xilinx.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
SD/MMC host controllers provide a SD Bus to plug SD cards,
but don't come with SD card plugged in :) Let the machine/board
model create and plug the SD cards when required.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200705211016.15241-5-f4bug@amsat.org>
We don't need to wait until realize() to create the SDBus,
create it in init() directly.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200705211016.15241-4-f4bug@amsat.org>
SD/MMC host controllers provide a SD Bus to plug SD cards,
but don't come with SD card plugged in :)
The machine/board object is where the SD cards are created.
Since the PXA2xx is not qdevified, for now create the cards
in pxa270_init() which is the SoC model.
In the future we will move this to the board model.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20200705213350.24725-2-f4bug@amsat.org>
Meson doesn't enjoy the same flexibility we have with Make in choosing
the include path. In particular the tracing headers are using
$(build_root)/$(<D).
In order to keep the include directives unchanged,
the simplest solution is to generate headers with patterns like
"trace/trace-audio.h" and place forwarding headers in the source tree
such that for example "audio/trace.h" includes "trace/trace-audio.h".
This patch is too ugly to be applied to the Makefiles now. It's only
a way to separate the changes to the tracing header files from the
Meson rewrite of the tracing logic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fixes: b98e8d1230
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Message-Id: <20200722204054.1400555-1-sw@weilnetz.de>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
[Commit message tweaked]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Only move the state machine to ReceivingData if there is no
pending error. This avoids later OOB access while processing
commands queued.
"SD Specifications Part 1 Physical Layer Simplified Spec. v3.01"
4.3.3 Data Read
Read command is rejected if BLOCK_LEN_ERROR or ADDRESS_ERROR
occurred and no data transfer is performed.
4.3.4 Data Write
Write command is rejected if BLOCK_LEN_ERROR or ADDRESS_ERROR
occurred and no data transfer is performed.
WP_VIOLATION errors are not modified: the error bit is set, we
stay in receive-data state, wait for a stop command. All further
data transfer is ignored. See the check on sd->card_status at the
beginning of sd_read_data() and sd_write_data().
Fixes: CVE-2020-13253
Cc: qemu-stable@nongnu.org
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Buglink: https://bugs.launchpad.net/qemu/+bug/1880822
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200630133912.9428-6-f4bug@amsat.org>
To make the next commit easier to review, clean this code first.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20200630133912.9428-3-f4bug@amsat.org>
QEMU allows to create SD card with unrealistic sizes. This could
work, but some guests (at least Linux) consider sizes that are not
a power of 2 as a firmware bug and fix the card size to the next
power of 2.
While the possibility to use small SD card images has been seen as
a feature, it became a bug with CVE-2020-13253, where the guest is
able to do OOB read/write accesses past the image size end.
In a pair of commits we will fix CVE-2020-13253 as:
Read command is rejected if BLOCK_LEN_ERROR or ADDRESS_ERROR
occurred and no data transfer is performed.
Write command is rejected if BLOCK_LEN_ERROR or ADDRESS_ERROR
occurred and no data transfer is performed.
WP_VIOLATION errors are not modified: the error bit is set, we
stay in receive-data state, wait for a stop command. All further
data transfer is ignored. See the check on sd->card_status at the
beginning of sd_read_data() and sd_write_data().
While this is the correct behavior, in case QEMU create smaller SD
cards, guests still try to access past the image size end, and QEMU
considers this is an invalid address, thus "all further data transfer
is ignored". This is wrong and make the guest looping until
eventually timeouts.
Fix by not allowing invalid SD card sizes (suggesting the expected
size as a hint):
$ qemu-system-arm -M orangepi-pc -drive file=rootfs.ext2,if=sd,format=raw
qemu-system-arm: Invalid SD card size: 60 MiB
SD card size has to be a power of 2, e.g. 64 MiB.
You can resize disk images with 'qemu-img resize <imagefile> <new-size>'
(note that this will lose data if you make the image smaller than it currently is).
Cc: qemu-stable@nongnu.org
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20200713183209.26308-8-f4bug@amsat.org>
We don't need to check if sd->blk is set twice.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200630133912.9428-18-f4bug@amsat.org>
Only SCSD cards support Class 6 (Block Oriented Write Protection)
commands.
"SD Specifications Part 1 Physical Layer Simplified Spec. v3.01"
4.3.14 Command Functional Difference in Card Capacity Types
* Write Protected Group
SDHC and SDXC do not support write-protected groups. Issuing
CMD28, CMD29 and CMD30 generates the ILLEGAL_COMMAND error.
Cc: qemu-stable@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200630133912.9428-7-f4bug@amsat.org>
If we want to check error after errp-function call, we need to
introduce local_err and then propagate it to errp. Instead, use
the ERRP_GUARD() macro, benefits are:
1. No need of explicit error_propagate call
2. No need of explicit local_err variable: use errp directly
3. ERRP_GUARD() leaves errp as is if it's not NULL or
&error_fatal, this means that we don't break error_abort
(we'll abort on error_set, not on error_propagate)
If we want to add some info to errp (by error_prepend() or
error_append_hint()), we must use the ERRP_GUARD() macro.
Otherwise, this info will not be added when errp == &error_fatal
(the program will exit prior to the error_append_hint() or
error_prepend() call). No such cases are being fixed here.
This commit is generated by command
sed -n '/^SD (Secure Card)$/,/^$/{s/^F: //p}' \
MAINTAINERS | \
xargs git ls-files | grep '\.[hc]$' | \
xargs spatch \
--sp-file scripts/coccinelle/errp-guard.cocci \
--macro-file scripts/cocci-macro-file.h \
--in-place --no-show-diff --max-width 80
Reported-by: Kevin Wolf <kwolf@redhat.com>
Reported-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Commit message tweaked]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200707165037.1026246-4-armbru@redhat.com>
[ERRP_AUTO_PROPAGATE() renamed to ERRP_GUARD(), and
auto-propagated-errp.cocci to errp-guard.cocci. Commit message
tweaked again.]
When all we do with an Error we receive into a local variable is
propagating to somewhere else, we can just as well receive it there
right away. Convert
if (!foo(..., &err)) {
...
error_propagate(errp, err);
...
return ...
}
to
if (!foo(..., errp)) {
...
...
return ...
}
where nothing else needs @err. Coccinelle script:
@rule1 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
binary operator op;
constant c1, c2;
symbol false;
@@
if (
(
- fun(args, &err, args2)
+ fun(args, errp, args2)
|
- !fun(args, &err, args2)
+ !fun(args, errp, args2)
|
- fun(args, &err, args2) op c1
+ fun(args, errp, args2) op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
)
}
@rule2 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
expression var;
binary operator op;
constant c1, c2;
symbol false;
@@
- var = fun(args, &err, args2);
+ var = fun(args, errp, args2);
... when != err
if (
(
var
|
!var
|
var op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
|
return var;
)
}
@depends on rule1 || rule2@
identifier err;
@@
- Error *err = NULL;
... when != err
Not exactly elegant, I'm afraid.
The "when != lbl:" is necessary to avoid transforming
if (fun(args, &err)) {
goto out
}
...
out:
error_propagate(errp, err);
even though other paths to label out still need the error_propagate().
For an actual example, see sclp_realize().
Without the "when strict", Coccinelle transforms vfio_msix_setup(),
incorrectly. I don't know what exactly "when strict" does, only that
it helps here.
The match of return is narrower than what I want, but I can't figure
out how to express "return where the operand doesn't use @err". For
an example where it's too narrow, see vfio_intx_enable().
Silently fails to convert hw/arm/armsse.c, because Coccinelle gets
confused by ARMSSE being used both as typedef and function-like macro
there. Converted manually.
Line breaks tidied up manually. One nested declaration of @local_err
deleted manually. Preexisting unwanted blank line dropped in
hw/riscv/sifive_e.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-35-armbru@redhat.com>
The previous commit enables conversion of
qdev_prop_set_drive_err(..., &err);
if (err) {
...
}
to
if (!qdev_prop_set_drive_err(..., errp)) {
...
}
Coccinelle script:
@@
identifier fun = qdev_prop_set_drive_err;
expression list args;
typedef Error;
Error *err;
@@
- fun(args, &err);
- if (err)
+ if (!fun(args, &err))
{
...
}
One line break tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-33-armbru@redhat.com>
The previous commit enables conversion of
foo(..., &err);
if (err) {
...
}
to
if (!foo(..., errp)) {
...
}
for QOM functions that now return true / false on success / error.
Coccinelle script:
@@
identifier fun = {
object_apply_global_props, object_initialize_child_with_props,
object_initialize_child_with_propsv, object_property_get,
object_property_get_bool, object_property_parse, object_property_set,
object_property_set_bool, object_property_set_int,
object_property_set_link, object_property_set_qobject,
object_property_set_str, object_property_set_uint, object_set_props,
object_set_propv, user_creatable_add_dict,
user_creatable_complete, user_creatable_del
};
expression list args, args2;
typedef Error;
Error *err;
@@
- fun(args, &err, args2);
- if (err)
+ if (!fun(args, &err, args2))
{
...
}
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-29-armbru@redhat.com>
The object_property_set_FOO() setters take property name and value in
an unusual order:
void object_property_set_FOO(Object *obj, FOO_TYPE value,
const char *name, Error **errp)
Having to pass value before name feels grating. Swap them.
Same for object_property_set(), object_property_get(), and
object_property_parse().
Convert callers with this Coccinelle script:
@@
identifier fun = {
object_property_get, object_property_parse, object_property_set_str,
object_property_set_link, object_property_set_bool,
object_property_set_int, object_property_set_uint, object_property_set,
object_property_set_qobject
};
expression obj, v, name, errp;
@@
- fun(obj, v, name, errp)
+ fun(obj, name, v, errp)
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Convert that one manually.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Fails to convert hw/rx/rx-gdbsim.c, because Coccinelle gets confused
by RXCPU being used both as typedef and function-like macro there.
Convert manually. The other files using RXCPU that way don't need
conversion.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-27-armbru@redhat.com>
[Straightforwad conflict with commit 2336172d9b "audio: set default
value for pcspk.iobase property" resolved]
Convert
foo(..., &err);
if (err) {
...
}
to
if (!foo(..., &err)) {
...
}
for qdev_realize(), qdev_realize_and_unref(), qbus_realize() and their
wrappers isa_realize_and_unref(), pci_realize_and_unref(),
sysbus_realize(), sysbus_realize_and_unref(), usb_realize_and_unref().
Coccinelle script:
@@
identifier fun = {
isa_realize_and_unref, pci_realize_and_unref, qbus_realize,
qdev_realize, qdev_realize_and_unref, sysbus_realize,
sysbus_realize_and_unref, usb_realize_and_unref
};
expression list args, args2;
typedef Error;
Error *err;
@@
- fun(args, &err, args2);
- if (err)
+ if (!fun(args, &err, args2))
{
...
}
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Nothing to convert there; skipped.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Converted manually.
A few line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200707160613.848843-5-armbru@redhat.com>
The FROM_SSI_SLAVE() macro predates QOM and is used as a typesafe way
to cast from an SSISlave* to the instance struct of a subtype of
TYPE_SSI_SLAVE. Switch to using the QOM cast macros instead, which
have the same effect (by writing the QOM macros if the types were
previously missing them.)
(The FROM_SSI_SLAVE() macro allows the SSISlave member of the
subtype's struct to be anywhere as long as it is named "ssidev",
whereas a QOM cast macro insists that it is the first thing in the
subtype's struct. This is true for all the types we convert here.)
This removes all the uses of FROM_SSI_SLAVE() so we can delete the
definition.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200628142429.17111-18-peter.maydell@linaro.org
milkymist_memcard_realize() leaks an Error object when realization of
its "sd-card" device fails. Quite harmless, since we only ever
realize this once, in milkymist_init() via milkymist_memcard_create().
Plug the leak.
Fixes: 3d0369ba49
Cc: Philippe Mathieu-Daudé <philmd@redhat.com>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200630090351.1247703-10-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call.
milkymist_memcard_realize() is wrong that way: it passes &err to
qdev_prop_set_drive_err() and qdev_realize_and_unref(). Currently
harmless, because the latter uses it only as first argument of
error_propagate().
Making qdev_prop_set_drive_err() fail involves abuse of -global.
Leave handling that to qdev_prop_set_drive(), like we do elsewhere.
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200622094227.1271650-17-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
On error, pxa2xx_mmci_init() reports to stderr and returns NULL.
Callers don't check for errors. Machines akita, borzoi, mainstone,
spitz, terrier, tosa, and z2 crash shortly after, like this:
$ qemu-system-aarch64 -M akita -drive if=sd,readonly=on
qemu-system-aarch64: failed to init SD card: Cannot use read-only drive as SD card
Segmentation fault (core dumped)
Machines connex and verdex reach the check for orphaned drives first:
$ aarch64-softmmu/qemu-system-aarch64 -M connex -drive if=sd,readonly=on -accel qtest
qemu-system-aarch64: failed to init SD card: Cannot use read-only drive as SD card
qemu-system-aarch64: -drive if=sd,readonly=on: machine type does not support if=sd,bus=0,unit=0
Make pxa2xx_mmci_init() fail cleanly right away.
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200622094227.1271650-16-armbru@redhat.com>
qdev_prop_set_drive() can fail. None of the other qdev_prop_set_FOO()
can; they abort on error.
To clean up this inconsistency, rename qdev_prop_set_drive() to
qdev_prop_set_drive_err(), and create a qdev_prop_set_drive() that
aborts on error.
Coccinelle script to update callers:
@ depends on !(file in "hw/core/qdev-properties-system.c")@
expression dev, name, value;
symbol error_abort;
@@
- qdev_prop_set_drive(dev, name, value, &error_abort);
+ qdev_prop_set_drive(dev, name, value);
@@
expression dev, name, value, errp;
@@
- qdev_prop_set_drive(dev, name, value, errp);
+ qdev_prop_set_drive_err(dev, name, value, errp);
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200622094227.1271650-14-armbru@redhat.com>
The Linux kernel's IMX code now uses vendor specific commands.
This results in endless warnings when booting the Linux kernel.
sdhci-esdhc-imx 2194000.usdhc: esdhc_wait_for_card_clock_gate_off:
card clock still not gate off in 100us!.
Implement support for the vendor specific command implemented in IMX hardware
to be able to avoid this warning.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200603145258.195920-2-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is still the same transformation as in the previous commits, but
here the sysbus_init_child_obj() and its matching realize in are in
separate files. Fortunately, there's just one realize left to
convert.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-51-armbru@redhat.com>
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
Commit 260bc9d8aa "hw/sd/sd.c: QOMify" QOMified only the device
itself, not its users. It kept sd_init() around for non-QOMified
users.
More than four years later, three such users remain: omap1 (machines
cheetah, sx1, sx1-v1) and omap2 (machines n800, n810) are not
QOMified, and pl181 (machines integratorcp, realview-eb,
realview-eb-mpcore, realview-pb-a8 realview-pbx-a9, versatileab,
versatilepb, vexpress-a15, vexpress-a9) is not QOMified properly.
The issue I presently have with this: an "sd-card" device should plug
into an "sd-bus" (its DeviceClass member bus_type says so), but
sd_init() leaves it unplugged. This is normally a bug (I just fixed
some instances), and I'd like to assert proper pluggedness to prevent
regressions. However, the qdev-but-not-quite thing returned by
sd_init() would fail the assertion. Meh.
Make sd_init() hide it from QOM/qdev. Visible in "info qom-tree",
here's the change for cheetah:
/machine (cheetah-machine)
[...]
/unattached (container)
[...]
/device[5] (serial-mm)
/serial (serial)
/serial[0] (qemu:memory-region)
- /device[6] (sd-card)
- /device[7] (omap-gpio)
+ /device[6] (omap-gpio)
[rest of device[*] renumbered...]
Cc: "Philippe Mathieu-Daudé" <philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200609122339.937862-24-armbru@redhat.com>
pxa2xx_mmci_init() creates a "pxa2xx-mmci" device, but neglects to
realize it. Affects machines akita, borzoi, connex, mainstone, spitz,
terrier, tosa, verdex, and z2.
In theory, a device becomes real only on realize. In practice, the
transition from unreal to real is a fuzzy one. The work to make a
device real can be spread between realize methods (fine),
instance_init methods (wrong), and board code wiring up the device
(fine as long as it effectively happens on realize). Depending on
what exactly is done where, a device can work even when we neglect
to realize it.
This one appears to work. Nevertheless, it's a clear misuse of the
interface. Even when it works today (more or less by chance), it can
break tomorrow.
Fix by realizing it right away. Visible in "info qom-tree"; here's
the change for akita:
/machine (akita-machine)
[...]
/unattached (container)
[...]
+ /device[5] (pxa2xx-mmci)
+ /pxa2xx-mmci[0] (qemu:memory-region)
+ /sd-bus (pxa2xx-mmci-bus)
[rest of device[*] renumbered...]
Fixes: 7a9468c925
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200609122339.937862-4-armbru@redhat.com>
Replace
error_report("...: %s", ..., error_get_pretty(err));
by
error_reportf_err(err, "...: ", ...);
One of the replaced messages lacked a colon. Add it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200505101908.6207-6-armbru@redhat.com>
Devices may have component devices and buses.
Device realization may fail. Realization is recursive: a device's
realize() method realizes its components, and device_set_realized()
realizes its buses (which should in turn realize the devices on that
bus, except bus_set_realized() doesn't implement that, yet).
When realization of a component or bus fails, we need to roll back:
unrealize everything we realized so far. If any of these unrealizes
failed, the device would be left in an inconsistent state. Must not
happen.
device_set_realized() lets it happen: it ignores errors in the roll
back code starting at label child_realize_fail.
Since realization is recursive, unrealization must be recursive, too.
But how could a partly failed unrealize be rolled back? We'd have to
re-realize, which can fail. This design is fundamentally broken.
device_set_realized() does not roll back at all. Instead, it keeps
unrealizing, ignoring further errors.
It can screw up even for a device with no buses: if the lone
dc->unrealize() fails, it still unregisters vmstate, and calls
listeners' unrealize() callback.
bus_set_realized() does not roll back either. Instead, it stops
unrealizing.
Fortunately, no unrealize method can fail, as we'll see below.
To fix the design error, drop parameter @errp from all the unrealize
methods.
Any unrealize method that uses @errp now needs an update. This leads
us to unrealize() methods that can fail. Merely passing it to another
unrealize method cannot cause failure, though. Here are the ones that
do other things with @errp:
* virtio_serial_device_unrealize()
Fails when qbus_set_hotplug_handler() fails, but still does all the
other work. On failure, the device would stay realized with its
resources completely gone. Oops. Can't happen, because
qbus_set_hotplug_handler() can't actually fail here. Pass
&error_abort to qbus_set_hotplug_handler() instead.
* hw/ppc/spapr_drc.c's unrealize()
Fails when object_property_del() fails, but all the other work is
already done. On failure, the device would stay realized with its
vmstate registration gone. Oops. Can't happen, because
object_property_del() can't actually fail here. Pass &error_abort
to object_property_del() instead.
* spapr_phb_unrealize()
Fails and bails out when remove_drcs() fails, but other work is
already done. On failure, the device would stay realized with some
of its resources gone. Oops. remove_drcs() fails only when
chassis_from_bus()'s object_property_get_uint() fails, and it can't
here. Pass &error_abort to remove_drcs() instead.
Therefore, no unrealize method can fail before this patch.
device_set_realized()'s recursive unrealization via bus uses
object_property_set_bool(). Can't drop @errp there, so pass
&error_abort.
We similarly unrealize with object_property_set_bool() elsewhere,
always ignoring errors. Pass &error_abort instead.
Several unrealize methods no longer handle errors from other unrealize
methods: virtio_9p_device_unrealize(),
virtio_input_device_unrealize(), scsi_qdev_unrealize(), ...
Much of the deleted error handling looks wrong anyway.
One unrealize methods no longer ignore such errors:
usb_ehci_pci_exit().
Several realize methods no longer ignore errors when rolling back:
v9fs_device_realize_common(), pci_qdev_unrealize(),
spapr_phb_realize(), usb_qdev_realize(), vfio_ccw_realize(),
virtio_device_realize().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-17-armbru@redhat.com>
Fixes the following coccinelle warnings:
$ spatch --sp-file --verbose-parsing ... \
scripts/coccinelle/remove_local_err.cocci
...
SUSPICIOUS: a \ character appears outside of a #define at ./target/ppc/translate_init.inc.c:5213
SUSPICIOUS: a \ character appears outside of a #define at ./target/ppc/translate_init.inc.c:5261
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:166
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:167
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:169
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:170
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:171
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:172
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:173
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5787
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5789
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5800
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5801
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5802
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5804
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5805
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5806
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:6329
SUSPICIOUS: a \ character appears outside of a #define at ./hw/sd/sdhci.c:1133
SUSPICIOUS: a \ character appears outside of a #define at ./hw/scsi/scsi-disk.c:3081
SUSPICIOUS: a \ character appears outside of a #define at ./hw/net/virtio-net.c:1529
SUSPICIOUS: a \ character appears outside of a #define at ./hw/riscv/sifive_u.c:468
SUSPICIOUS: a \ character appears outside of a #define at ./dump/dump.c:1895
SUSPICIOUS: a \ character appears outside of a #define at ./block/vhdx.c:2209
SUSPICIOUS: a \ character appears outside of a #define at ./block/vhdx.c:2215
SUSPICIOUS: a \ character appears outside of a #define at ./block/vhdx.c:2221
SUSPICIOUS: a \ character appears outside of a #define at ./block/vhdx.c:2222
SUSPICIOUS: a \ character appears outside of a #define at ./block/replication.c:172
SUSPICIOUS: a \ character appears outside of a #define at ./block/replication.c:173
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200412223619.11284-2-f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
It's wrong to use same err object as errp parameter for several
function calls without intermediate checking for error: we'll crash if
try to set err object twice. Fix that.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200317125741.15301-1-vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The Allwinner System on Chip families sun4i and above contain
an integrated storage controller for Secure Digital (SD) and
Multi Media Card (MMC) interfaces. This commit adds support
for the Allwinner SD/MMC storage controller with the following
emulated features:
* DMA transfers
* Direct FIFO I/O
* Short/Long format command responses
* Auto-Stop command (CMD12)
* Insert & remove card detection
The following boards are extended with the SD host controller:
* Cubieboard (hw/arm/cubieboard.c)
* Orange Pi PC (hw/arm/orangepi.c)
Signed-off-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200311221854.30370-9-nieklinnenbank@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since its introduction in commit d86a77f8ab, dma_memory_read()
always accepted void pointer argument. Remove the unnecessary
casts.
This commit was produced with the included Coccinelle script
scripts/coccinelle/exec_rw_const.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
---
v4: Drop parenthesis when removing cast (Eric Blake)
We have many files that apparently do not depend on the target CPU
configuration, i.e. which can be put into common-obj-y instead of
obj-y. This way, the code can be shared for example between
qemu-system-arm and qemu-system-aarch64, or the various big and
little endian variants like qemu-system-sh4 and qemu-system-sh4eb,
so that we do not have to compile the code multiple times anymore.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200130133841.10779-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Provide a temporary device_legacy_reset function doing what
device_reset does to prepare for the transition with Resettable
API.
All occurrence of device_reset in the code tree are also replaced
by device_legacy_reset.
The new resettable API has different prototype and semantics
(resetting child buses as well as the specified device). Subsequent
commits will make the changeover for each call site individually; once
that is complete device_legacy_reset() will be removed.
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200123132823.1117486-2-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 includes a second cut-down version of the SD/MMC controller
found in the AST2500, named the eMMC controller. It's cut down in the
sense that it only supports one slot rather than two, but it brings the
total number of slots supported by the AST2600 to three.
The existing code assumed that the SD controller always provided two
slots. Rework the SDHCI object to expose the number of slots as a
property to be set by the SoC configuration.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20200114103433.30534-2-clg@kaod.org
[PMM: fixed up to use device_class_set_props()]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20191205174635.18758-16-vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
This file keeps the various QDev blocks separated by comments.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cleber Rosa <crosa@redhat.com>
Message-id: 20191005154748.21718-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SOCs have two SD/MMC controllers. Add a device that
encapsulates both of these controllers and models the Aspeed-specific
registers and behavior.
Tested by reading from mmcblk0 in Linux:
qemu-system-arm -machine romulus-bmc -nographic \
-drive file=flash-romulus,format=raw,if=mtd \
-device sd-card,drive=sd0 -drive file=_tmp/kernel,format=raw,if=sd,id=sd0
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190925143248.10000-3-clg@kaod.org
[clg: - changed the controller MMIO window size to 0x1000
- moved the MMIO mapping of the SDHCI slots at the SoC level
- merged code to add SD drives on the SD buses at the machine level ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While the tracing framework does not forbid trailing newline in
events format string, using them lead to confuse output.
It is the responsibility of the backend to properly end an event
line.
Some of our formats have trailing newlines, remove them.
[Fixed typo in commit description reported by Eric Blake
<eblake@redhat.com>
--Stefan]
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190916095121.29506-2-philmd@redhat.com
Message-Id: <20190916095121.29506-2-philmd@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Almost a third of its inclusions are actually superfluous. Delete
them. Downgrade two more to qapi/qapi-types-run-state.h, and move one
from char/serial.h to char/serial.c.
hw/semihosting/config.c, monitor/monitor.c, qdev-monitor.c, and
stubs/semihost.c define variables declared in sysemu/sysemu.h without
including it. The compiler is cool with that, but include it anyway.
This doesn't reduce actual use much, as it's still included into
widely included headers. The next commit will tackle that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-27-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
Due to an off-by-one error, the assert statements allow an
out-of-bound array access. This doesn't happen in practice,
but the static analyzer notices.
Signed-off-by: Lidong Chen <lidong.chen@oracle.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-Id: <6b19cb7359a10a6bedc3ea0fce22fed3ef93c102.1560806687.git.lidong.chen@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rather than looking inside the definition of a BusState with "s->bus.qbus",
use the QOM prefered style: "BUS(&s->bus)".
This patch was generated using the following Coccinelle script:
// Use BUS() macros to access BusState.qbus
@use_bus_macro_to_access_qbus@
expression obj;
identifier bus;
@@
-&obj->bus.qbus
+BUS(&obj->bus)
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20190528164020.32250-6-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Header guard symbols should match their file name to make guard
collisions less likely.
Cleaned up with scripts/clean-header-guards.pl, followed by some
renaming of new guard symbols picked by the script to better ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-6-armbru@redhat.com>
[Rebase to master: update include/hw/net/ne2000-isa.h]
Tracked down with cleanup-trace-events.pl. Funnies requiring manual
post-processing:
* block.c and blockdev.c trace points are in block/trace-events.
* hw/block/nvme.c uses the preprocessor to hide its trace point use
from cleanup-trace-events.pl.
* include/hw/xen/xen_common.h trace points are in hw/xen/trace-events.
* net/colo-compare and net/filter-rewriter.c use pseudo trace points
colo_compare_udp_miscompare and colo_filter_rewriter_debug to guard
debug code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20190314180929.27722-5-armbru@redhat.com
Message-Id: <20190314180929.27722-5-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Some machines have an SDHCI device, but no PCI. To be able to
compile hw/sd/sdhci.c without CONFIG_PCI, we must not call functions
like pci_get_address_space() and pci_allocate_irq() there. Thus
move the PCI-related code into a separate file.
This is required for the new Kconfig-like build system, e.g. it is
needed if a user wants to compile a QEMU binary with just one machine
that has SDHCI, but no PCI, like the ARM "raspi" machines for example.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Instead of including the same list of devices for each target,
set CONFIG_PCI to true, and make the devices default to present
whenever PCI is available. However, s390x does not want all the
PCI devices, so there is a separate symbol to enable them.
Done mostly with the following script:
while read i; do
i=${i%=y}; i=${i#CONFIG_}
sed -i -e'/^config '$i'$/!b' -en \
-e'a\' -e' default y if PCI_DEVICES\' -e' depends on PCI' \
`grep -lw $i hw/*/Kconfig`
done < default-configs/pci.mak
followed by replacing a few "depends on" clauses with "select"
whenever the symbol is not really related to PCI.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-31-yang.zhong@intel.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Sets the category of the sd memory card as DEVICE_CATEGORY_STORAGE.
Devices should be assigned to one of DEVICE_CATEGORY_XXXX.
Signed-off-by: kumar sourav <sourav.jb1988@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190124162045.10474-1-sourav.jb1988@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
In sdhci_sysbus_realize() we override the initialization of
s->iomem that sdhci_common_realize() performs. However we
don't destroy the old memory region before reinitializing
it, which means that the memory allocated for mr->name in
memory_region_do_init() is leaked.
Since sdhci_initfn() already initializes s->io_ops to
&sdhci_mmio_ops, always use that in sdhci_common_realize()
and remove the now-unnecessary reinitialization of the
MMIO region from sdhci_sysbus_realize().
Spotted by clang's leak sanitizer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181204132952.2601-4-peter.maydell@linaro.org
Device models aren't supposed to go on fishing expeditions for
backends. They should expose suitable properties for the user to set.
For onboard devices, board code sets them.
Device ssi-sd picks up its block backend in its init() method with
drive_get_next() instead. This mistake is already marked FIXME since
commit af9e40a.
Unset user_creatable to remove the mistake from our external
interface. Since the SSI bus doesn't support hotplug, only -device
can be affected. Only certain ARM machines have ssi-sd and provide an
SSI bus for it; this patch breaks -device ssi-sd for these machines.
No actual use of -device ssi-sd is known.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-id: 20181009060835.4608-1-armbru@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the ESDHC PRSSTAT_SDSTB bit, using the value of SDHC_CLOCK_INT_STABLE.
Freescale recommends checking this bit when changing clock frequency.
Signed-off-by: Hans-Erik Floryd <hans-erik.floryd@rt-labs.com>
Message-id: 1534507843-4251-1-git-send-email-hans-erik.floryd@rt-labs.com
[PMM: fixed indentation]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Writes in PIO mode have two requirements:
- A data interrupt must be generated after a write command has been
issued to indicate that the chip is ready to receive data.
- A block interrupt must be generated after each block to indicate
that the chip is ready to receive the next data block.
Rearrange the code to make this happen. Tested on raspi3 (in PIO mode)
and raspi2 (in DMA mode).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 1531779837-20557-1-git-send-email-linux@roeck-us.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
DeviceClass::reset models a "cold power-on" reset which can
also be used to powercycle a device; but there is no "hot reset"
(a.k.a. soft-reset) method available.
The OMAP MMC Power-Up Control bit is not designed to powercycle
a card, but to disable it without powering it off (pseudo-reset):
Multimedia Card (MMC/SD/SDIO) Interface [SPRU765A]
MMC_CON[11] Power-Up Control (POW)
This bit must be set to 1 before any valid transaction to either
MMC/SD or SPI memory cards.
When 1, the card is considered powered-up and the controller core
is enabled.
When 0, the card is considered powered-down (system dependent),
and the controller core logic is in pseudo-reset state. This is,
the MMC_STAT flags and the FIFO pointers are reset, any access to
MMC_DATA[DATA] has no effect, a write into the MMC.CMD register
is ignored, and a setting of MMC_SPI[STR] to 1 is ignored.
By splitting the 'pseudo-reset' code out of the 'power-on' reset
function, this patch fixes a latent bug in omap_mmc_write(MMC_CON)i
recently exposed by ecd219f7ab.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180706162155.8432-2-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It eases code review, unit is explicit.
Patch generated using:
$ git grep -E '(1024|2048|4096|8192|(<<|>>).?(10|20|30))' hw/ include/hw/
and modified manually.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180625124238.25339-37-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The load/store API will ease further code movement.
Per the Physical Layer Simplified Spec. "3.6 Bus Protocol":
"In the CMD line the Most Significant Bit (MSB) is transmitted
first, the Least Significant Bit (LSB) is the last."
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We don't actually implement SD command CRC checking, because
for almost all of our SD controllers the CRC generation is
done in hardware, and so modelling CRC generation and checking
would be a bit pointless. (The exception is that milkymist-memcard
makes the guest software compute the CRC.)
As a result almost all of our SD controller models don't bother
to set the SDRequest crc field, and the SD card model doesn't
check it. So the tracing of it in sdbus_do_command() provokes
Coverity warnings about use of uninitialized data.
Drop the CRC field from the trace; we can always add it back
if and when we do anything useful with the CRC.
Fixes Coverity issues 1386072, 1386074, 1386076, 1390571.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180626180324.5537-1-peter.maydell@linaro.org
Per the Physical Layer Simplified Spec. "5.3 CSD Register":
"The maximum block length might therefore be in the range 512...2048 bytes"
Therefore 3 hexdigits are enough to report the block length.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-7-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These commands got introduced by Spec v3
(see 0c3fb03f7e and 4481bbc79d).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180607180641.874-7-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20180607180641.874-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
CMD8 is "Reserved" in Spec v1.10.
Spec v2.00 introduces the SEND_IF_COND command:
6.4.1 Power Up
CMD8 is newly added in the Physical Layer Specification Version
2.00 to support multiple voltage ranges and used to check whether
the card supports supplied voltage. The version 2.00 or later host
shall issue CMD8 and verify voltage before card initialization.
The host that does not support CMD8 shall supply high voltage range.
Message-Id: 201204252110.20873.paul@codesourcery.com
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180607180641.874-5-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As of this commit, the Spec v1 is not working, and all controllers
expect the cards to be conformant to Spec v2.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20180607180641.874-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From the "Physical Layer Simplified Specification Version 1.10"
Chapter 7.3 "SPI Mode Transaction Packets"
Table 57: "Commands and arguments"
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20180607180641.874-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The initial implementation is based on the Specs v1.10 (see a1bb27b1e9).
However the SCR is anouncing the card being v1.01.
The new chapters added in version 1.10 are:
4.3.10 Switch function command
Switch function command (CMD6) 1 is used to switch or expand
memory card functions. [...]
This is a new feature, introduced in SD physical Layer
Specification Version 1.10. Therefore, cards that are
compatible with earlier versions of the spec do not support
it. The host shall check the "SD_SPEC" field in the SCR
register to recognize what version of the spec the card
complies with before using CMD6. It is mandatory for SD
memory card of Ver1.10 to support CMD6.
4.3.11 High-Speed mode (25MB/sec interface speed)
Though the Rev 1.01 SD memory card supports up to 12.5MB/sec
interface speed, the speed of 25MB/sec is necessary to support
increasing performance needs of the host and because of memory
size which continues to grow.
To achieve 25MB/sec interface speed, clock rate is increased to
50MHz and CLK/CMD/DAT signal timing and circuit conditions are
reconsidered and changed from Physical Layer Specification
Version 1.01.
4.3.12 Command system (This chapter is newly added in version 1.10)
SD commands CMD34-37, CMD50, CMD57 are reserved for SD command
system expansion via the switch command.
[These commands] will be considered as illegal commands (as
defined in revision 1.01 of the SD physical layer specification).
The SWITCH_FUNCTION is implemented since the first commit, a1bb27b1e9.
The 25MB/sec High-Speed mode was already updated in d7ecb86752.
The current implementation does not implements CMD34-37, CMD50 and
CMD57, thus these commands already return ILLEGAL.
With this patch, the SCR register now matches the description of the header:
* SD Memory Card emulation as defined in the "SD Memory Card Physical
* layer specification, Version 1.10."
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180607180641.874-2-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180606152128.449-2-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbEXNvAAoJECgfDbjSjVRpc8gH/R8xrcFrV+k9wwbgYcOcGb6Y
LWjseE31pqJcxRV80vLOdzYEuLStZQKQQY7xBDMlA5vdyvZxIA6FLO2IsiJSbFAk
EK8pclwhpwQAahr8BfzenabohBv2UO7zu5+dqSvuJCiMWF3jGtPAIMxInfjXaOZY
odc1zY2D2EgsC7wZZ1hfraRbISBOiRaez9BoGDKPOyBY9G1ASEgxJgleFgoBLfsK
a1XU+fDM6hAVdxftfkTm0nibyf7PWPDyzqghLqjR9WXLvZP3Cqud4p8N29mY51pR
KSTjA4FYk6Z9EVMltyBHfdJs6RQzglKjxcNGdlrvacDfyFi79fGdiosVllrjfJM=
=3+V0
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
acpi, vhost, misc: fixes, features
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 01 Jun 2018 17:25:19 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (31 commits)
vhost-blk: turn on pre-defined RO feature bit
ACPI testing: test NFIT platform capabilities
nvdimm, acpi: support NFIT platform capabilities
tests/.gitignore: add entry for generated file
arch_init: sort architectures
ui: use local path for local headers
qga: use local path for local headers
colo: use local path for local headers
migration: use local path for local headers
usb: use local path for local headers
sd: fix up include
vhost-scsi: drop an unused include
ppc: use local path for local headers
rocker: drop an unused include
e1000e: use local path for local headers
ioapic: fix up includes
ide: use local path for local headers
display: use local path for local headers
trace: use local path for local headers
migration: drop an unused include
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
