This patch implements the FIFO mode of the SMBus module. In FIFO, the
user transmits or receives at most 16 bytes at a time. The FIFO mode
allows the module to transmit large amount of data faster than single
byte mode.
Since we only added the device in a patch that is only a few commits
away in the same patch set. We do not increase the VMstate version
number in this special case.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-6-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit implements the single-byte mode of the SMBus.
Each Nuvoton SoC has 16 System Management Bus (SMBus). These buses
compliant with SMBus and I2C protocol.
This patch implements the single-byte mode of the SMBus. In this mode,
the user sends or receives a byte each time. The SMBus device transmits
it to the underlying i2c device and sends an interrupt back to the QEMU
guest.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-2-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
This patch contains all the files, whose maintainer I could not get
from ‘get_maintainer.pl’ script.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023124424.20177-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Adapted exec.c and qdev-monitor.c to new location]
Signed-off-by: Thomas Huth <thuth@redhat.com>
VMStateDescription.fields should be end with VMSTATE_END_OF_LIST().
However, microbit_i2c_vmstate doesn't follow it. Let's change it.
Fixes: 9d68bf564e ("arm: Stub out NRF51 TWI magnetometer/accelerometer detection")
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Peng Liang <liangpeng10@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201019093401.2993833-1-liangpeng10@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Meson doesn't enjoy the same flexibility we have with Make in choosing
the include path. In particular the tracing headers are using
$(build_root)/$(<D).
In order to keep the include directives unchanged,
the simplest solution is to generate headers with patterns like
"trace/trace-audio.h" and place forwarding headers in the source tree
such that for example "audio/trace.h" includes "trace/trace-audio.h".
This patch is too ugly to be applied to the Makefiles now. It's only
a way to separate the changes to the tracing header files from the
Meson rewrite of the tracing logic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We use "create_simple" names for functions that allocate, initialize,
configure and realize device objects: pci_create_simple(),
isa_create_simple(), usb_create_simple(). For consistency, rename
i2c_create_slave() as i2c_slave_create_simple(). Since we have
to update all the callers, also let it return a I2CSlave object.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-5-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The other i2c functions are called i2c_slave_FOO(). Rename as
i2c_slave_realize_and_unref() to be consistent.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-4-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We use "new" names for functions that allocate and initialize
device objects: pci_new(), isa_new(), usb_new().
Let's call this one i2c_slave_new(). Since we have to update
all the callers, also let it return a I2CSlave object.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-3-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
All the callers of aspeed_i2c_get_bus() have a AspeedI2CState and
cast it to a DeviceState with DEVICE(), then aspeed_i2c_get_bus()
cast the DeviceState to an AspeedI2CState with ASPEED_I2C()...
Simplify aspeed_i2c_get_bus() callers by using AspeedI2CState
argument.
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-2-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The System Management Bus is more or less a derivative of the I2C
bus, thus the Kconfig entry depends of I2C.
Not all boards providing an I2C bus support SMBus.
Use two different Kconfig entries to be able to select I2C without
selecting SMBus.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191231183216.6781-6-philmd@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Extract i2c_try_create_slave() and i2c_realize_and_unref()
from i2c_create_slave().
We can now set properties on a I2CSlave before it is realized.
This is in line with the recent qdev/QOM changes merged
in commit 6675a653d2.
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20200623072723.6324-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
'ARM SBCon two-wire serial bus interface' is the official
name describing the pair of registers used to bitbanging
I2C in the Versatile boards.
Make the private VersatileI2CState structure as public
ArmSbconI2CState.
Add the TYPE_ARM_SBCON_I2C, alias to our current
TYPE_VERSATILE_I2C model.
Rename the memory region description as 'arm_sbcon_i2c'.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200617072539.32686-5-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use self-explicit definitions instead of magic values.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200617072539.32686-4-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use self-explicit definitions instead of magic values.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200617072539.32686-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
The DEVICE() macro is defined as:
#define DEVICE(obj) OBJECT_CHECK(DeviceState, (obj), TYPE_DEVICE)
which expands to:
((DeviceState *)object_dynamic_cast_assert((Object *)(obj), (name),
__FILE__, __LINE__,
__func__))
This assertion can only fail when @obj points to something other
than its stated type, i.e. when we're in undefined behavior country.
Remove the unnecessary DEVICE() casts when we already know the
pointer is of DeviceState type.
Patch created mechanically using spatch with this script:
@@
typedef DeviceState;
DeviceState *s;
@@
- DEVICE(s)
+ s
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Paul Durrant <paul@xen.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Acked-by: John Snow <jsnow@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200512070020.22782-4-f4bug@amsat.org>
On the NRF51 series, all peripherals have a fixed I/O size
of 4KiB. Define NRF51_PERIPHERAL_SIZE and use it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200504072822.18799-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix warning reported by Clang static code analyzer:
CC hw/i2c/pm_smbus.o
hw/i2c/pm_smbus.c:187:17: warning: Value stored to 'ret' is never read
ret = 0;
^ ~
Reported-by: Clang Static Analyzer
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200422133152.16770-4-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
spd_data_generate() splits @ram_size bytes into @nbanks RAM banks of
1 << sz_log2 MiB each, like this:
size = ram_size >> 20; /* work in terms of megabytes */
[...]
nbanks = 1;
while (sz_log2 > max_log2 && nbanks < 8) {
sz_log2--;
nbanks++;
}
Each iteration halves the size of a bank, and increments the number of
banks. Wrong: it should double the number of banks.
The bug goes back all the way to commit b296b664ab "smbus: Add a
helper to generate SPD EEPROM data".
It can't bite because spd_data_generate()'s current users pass only
@ram_size that result in *zero* iterations:
machine RAM size #banks type bank size
fulong2e 256 MiB 1 DDR 256 MiB
sam460ex 2048 MiB 1 DDR2 2048 MiB
1024 MiB 1 DDR2 1024 MiB
512 MiB 1 DDR2 512 MiB
256 MiB 1 DDR2 256 MiB
128 MiB 1 SDR 128 MiB
64 MiB 1 SDR 64 MiB
32 MiB 1 SDR 32 MiB
Apply the obvious, minimal fix. I admit I'm tempted to rip out the
unused (and obviously untested) feature instead, because YAGNI.
Note that this is not the final result, as spd_data_generate() next
increases #banks from 1 to 2 if possible. This is done "to avoid a
bug in MIPS Malta firmware". We don't even use this function with
machine type malta. *Shrug*
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200422134815.1584-5-armbru@redhat.com>
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call.
spd_data_generate() can pass @errp to error_setg() more than once when
it adjusts both memory size and type. Harmless, because no caller
passes anything that needs adjusting. Until the previous commit,
sam460ex passed types that needed adjusting, but not sizes.
spd_data_generate()'s contract is rather awkward:
If everything's fine, return non-null and don't set an error.
Else, if memory size or type need adjusting, return non-null and
set an error describing the adjustment.
Else, return null and set an error reporting why no data can be
generated.
Its callers treat the error as a warning even when null is returned.
They don't create the "smbus-eeprom" device then. Suspicious.
Since the previous commit, only "everything's fine" can actually
happen. Drop the unused code and simplify the callers. This gets rid
of the error API violation.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200422134815.1584-3-armbru@redhat.com>
hw/i2c/smbus_ich9.c calls range_covers_byte(). Include "qemu/range.h"
which declares it.
This fixes (when modifying unrelated headers):
hw/i2c/smbus_ich9.c:66:9: error: implicit declaration of function 'range_covers_byte' is invalid in C99 [-Werror,-Wimplicit-function-declaration]
if (range_covers_byte(address, len, ICH9_SMB_HOSTC)) {
^
Acked-by: John Snow <jsnow@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200228114649.12818-14-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
We have many files that apparently do not depend on the target CPU
configuration, i.e. which can be put into common-obj-y instead of
obj-y. This way, the code can be shared for example between
qemu-system-arm and qemu-system-aarch64, or the various big and
little endian variants like qemu-system-sh4 and qemu-system-sh4eb,
so that we do not have to compile the code multiple times anymore.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200130133841.10779-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Define the new macro VMSTATE_INSTANCE_ID_ANY for callers who wants to
auto-generate the vmstate instance ID. Previously it was hard coded
as -1 instead of this macro. It helps to change this default value in
the follow up patches. No functional change.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Since clocks are not QOM objects, replace PROP_PTR of clocks with
setters methods.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Instead, set the initial data field directly.
(the initial data is an array of 256 bytes. As I don't know if it may
change over time, I keep the pointer to original buffer as is, but it
might be worth to consider to copy it instead)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-6-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The I2C controller of the Aspeed AST2500 and AST2600 SoCs supports DMA
transfers to and from DRAM.
A pair of registers defines the buffer address and the length of the
DMA transfer. The address should be aligned on 4 bytes and the maximum
length should not exceed 4K. The receive or transmit DMA transfer can
then be initiated with specific bits in the Command/Status register of
the controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SRAM must be enabled before using the Buffer Pool mode or the DMA
mode. This is not required on other SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed I2C controller can operate in different transfer modes :
- Byte Buffer mode, using a dedicated register to transfer a
byte. This is what the model supports today.
- Pool Buffer mode, using an internal SRAM to transfer multiple
bytes in the same command sequence.
Each SoC has different SRAM characteristics. On the AST2400, 2048
bytes of SRAM are available at offset 0x800 of the controller AHB
window. The pool buffer can be configured from 1 to 256 bytes per bus.
On the AST2500, the SRAM is at offset 0x200 and the pool buffer is of
16 bytes per bus.
On the AST2600, the SRAM is at offset 0xC00 and the pool buffer is of
32 bytes per bus. It can be splitted in two for TX and RX but the
current model does not add support for it as it it unused by known
drivers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The I2C controller of the AST2400 and AST2500 SoCs have one IRQ shared
by all I2C busses. The AST2600 SoC I2C controller has one IRQ per bus
and 16 busses.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-17-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It prepares ground for register differences between SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-16-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Almost a third of its inclusions are actually superfluous. Delete
them. Downgrade two more to qapi/qapi-types-run-state.h, and move one
from char/serial.h to char/serial.c.
hw/semihosting/config.c, monitor/monitor.c, qdev-monitor.c, and
stubs/semihost.c define variables declared in sysemu/sysemu.h without
including it. The compiler is cool with that, but include it anyway.
This doesn't reduce actual use much, as it's still included into
widely included headers. The next commit will tackle that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-27-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
Currently the bitbang_i2c_init() function allocates a
bitbang_i2c_interface struct which it returns. This is unfortunate
because it means that if the function is used from a DeviceState
init method then the memory will be leaked by an "init then delete"
cycle, as used by the qmp/hmp commands that list device properties.
Since three out of four of the uses of this function are in
device init methods, switch the function to do an in-place
initialization of a struct that can be embedded in the
device state struct of the caller.
This fixes LeakSanitizer leak warnings that have appeared in the
patchew configuration (which only tries to run the sanitizers
for the x86_64-softmmu target) now that we use the bitbang-i2c
code in an x86-64 config.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190702163844.20458-1-peter.maydell@linaro.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The bitbang i2c implementation is also useful for other device models
such as DDC in display controllers. Move the header to include/hw/i2c/
to allow it to be used from other device models and adjust users of
this include. This also reverts commit 2b4c1125ac which is no longer
needed.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-id: 5d1fe4db846ab9be4b77ddb0d43cc74cd200a003.1561028123.git.balaton@eik.bme.hu
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch is slightly based on earlier work by Ákos Kovács (i.e.
his "hw/arm/Kconfig: Add ARM Kconfig" patch).
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The license information in this file is rather confusing. The text
declares LGPL first, but then says that contributions after Jan 2012
are licensed under the GPL instead. How should the average user who
just downloaded the release tarball know which part is now GPL and
which is LGPL? Also, as far as I can see, the file has been added to
QEMU *after* January in 2012, so the whole file should be GPL by
default instead.
Furthermore, looking at the text of the LGPL (see COPYING.LIB in the
top directory), the license clearly states in section "3." that one
should rather replace the license information in such a case instead.
Thus let's clean up the confusing statements and use the proper GPL
text only.
Message-Id: <1549471435-21887-1-git-send-email-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Move it together with the other EDID code. hw/i2c should only
include the core and the adapters, not the slaves.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20190325155923.30987-1-pbonzini@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Original commit message:
This patch adds an emulation model for i2c controller found on most of the FSL SoCs.
It also integrates the RTC (ds1338) that sits on the i2c Bus with e500 machine model.
Patch was originally written by Amit Singh Tomar <amit.tomar@freescale.com>
see http://patchwork.ozlabs.org/patch/431475/
I only fixed it enough for application on top of current qemu master
20b084c4b1, and hopefully fixed checkpatch errors
Tested by booting Linux kernel 4.20.12. Now e500 machine doesn't need
network time protocol daemon because it will have working RTC
(before all timestamps on files were from 2016)
Signed-off-by: Amit Singh Tomar <amit.tomar@freescale.com>
Signed-off-by: Andrew Randrianasulu <randrianasulu@gmail.com>
Message-Id: <20190306102812.28972-1-randrianasulu@gmail.com>
[dwg: Add Kconfig stanza to define the new symbol, update MAINTAINERS]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-40-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-38-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This way, the default-configs file only need to specify the boards
and any optional devices.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-37-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reset the contents to init data and reset the offset on a machine
reset.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Transfer the state of the EEPROM on a migration. This way the
data remains consistent on migration.
This required moving the actual data to a separate array and
using the data provided in the init function as a separate
initialization array, since a pointer property has to be a
void * and the array needs to be uint8_t[].
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
It was hard-coded to 256 in a number of places, create a constant
for that.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Create a type name and a cast macro and use those through the
code.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
There is no vmstate handling for SMBus, so no device sitting on SMBus
can have a state transfer that works reliably. So add it.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Transfer the state information for the SMBus registers and
internal data so it will work on a VM transfer.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The I2C block read function of pm_smbus was completely broken. It
required doing some direct I2C handling because it didn't have a
defined size, the OS code just reads bytes until it marks the
transaction finished.
This also required adjusting how the AMIBIOS workaround code worked,
the I2C block mode was setting STS_HOST_BUSY during a transaction,
so that bit could no longer be used to inform the host status read
code to start the transaction. Create a explicit bool for that
operation.
Also, don't read the next byte from the device in byte-by-byte
mode unless the OS is actually clearing the byte done bit. Just
assuming that's what the OS is doing is a bad idea.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
There were two different read functions, and with the removal of
the command passed in there is no functional difference. So remove
one of them. With that you don't need one of the states, so that
can be removed, too.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
There were two different write functions and the SMBus code kept
track of the command.
Keeping track of the command wasn't useful, in fact it wasn't quite
correct for the eeprom_smbus code. And there is no need for two write
functions. Just have one write function and the first byte in the
buffer is the command.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The logic of handling quick SMBus commands was wrong. If you get a
finish event with no data, that's a quick command.
Document the quick command while we are at it.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
i2c_recv() cannot fail, so there is no need to check the return
value. It also returns unt8_t, so comparing with < 0 is not
meaningful.
Fix up various I2C controllers to remove the unneeded code.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
It is never supposed to fail and cannot return an error, so just
have it return the proper type. Have it return 0xff on nothing
available, since that's what would happen on a real bus.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
smbus.c and smbus.h had device side code, master side code, and
smbus.h has some smbus_eeprom.c definitions. Split them into
separate files.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Create separate variables for these components, they are
used in many boards but not all. This allows finer-grain
selection of the included code with default-configs/*.mak.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are several boards with SPD EEPROMs that are now using
duplicated or slightly different hard coded data. Add a helper to
generate SPD data for a memory module of given type and size that
could be used by these boards (either as is or with further changes if
needed) which should help cleaning this up and avoid further duplication.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Recent microbit firmwares panic if the TWI magnetometer/accelerometer
devices are not detected during startup. We don't implement TWI (I2C)
so let's stub out these devices just to let the firmware boot.
Signed-off by: Steffen Görtz <contrib@steffen-goertz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190110094020.18354-2-stefanha@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: fixed comment style]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clang 3.4 considers duplicate typedef in ppc4xx_i2c.h and
bitbang_i2c.h an error even if they are identical. Move it to a common
place to allow building with this clang version.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
While performing block transfer write in smb_ioport_writeb(),
'smb_index' is incremented and used to index smb_data[] array.
Check 'smb_index' value to avoid OOB access.
Note that this bug is exploitable by a guest to escape
from the virtual machine. However the commit which
introduced the bug was only made after the 3.0 release,
and so it is not present in any released QEMU versions.
Fixes: 38ad4fae43 i2c: pm_smbus: Add block transfer capability
Reported-by: Michael Hanselmann <public@hansmi.ch>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Michael Hanselmann <public@hansmi.ch>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20181206121830.6177-1-ppandit@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This also makes the default display resolution configurable,
via xres and yres properties. The default is 1024x768.
The old code had a hard-coded resolution of 1600x1200.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20181005110837.28209-1-kraxel@redhat.com
The AST2500 datasheet says:
I2CD10 Interrupt Status Register
bit 2 Receive Done Interrupt status
S/W needs to clear this status bit to allow next data receiving
The Rx interrupt done interrupt status bit needs to be cleared
explicitly before the next byte can be received, and must therefore
not be auto-cleared. Also, receiving the next byte must be delayed
until the bit has been cleared.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180914063506.20815-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Receive command handling may have to be deferred if a previous receive
done interrupt was not yet acknowledged. Move receive command handling
into a separate function to prepare for the necessary changes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180914063506.20815-3-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
aspeed i2c interrupts should be cleared by software only, and the bus
interrupt should be lowered when all interrupts have been cleared.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180914063506.20815-2-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: drop TODO comment describing an issue which is
fixed later in the patch series, and clean up commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The PIIX4 hardware has block transfer buffer always enabled in
the hardware, but the i801 does not. Add a parameter to pm_smbus_init
to force on the block transfer so the PIIX4 handler can enable this
by default, as it was disabled by default before.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1534796770-10295-9-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Change 880b1ffe6e "smbus: do not immediately complete commands"
changed pm_smbus to delay setting the host busy bit until the status
register was read, to work around a bug in AMIBIOS. Unfortunately,
when interrupts are enabled, the status register will never get read
and the processing will never happen.
Modify the code to only delay setting the host busy bit if interrupts
are not enabled.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Hervé Poussineau <hpoussin@reactos.org>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1534796770-10295-8-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the necessary code so that interrupts actually work from
the pm_smbus device.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1534796770-10295-7-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There was no block transfer code in pm_smbus.c, and it is needed
for some devices. So add it.
This adds both byte-by-byte block transfers and buffered block
transfers.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1534796770-10295-5-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It did have write capability, but the manual says the behavior
with write enabled is undefined. So just set an error in this
case.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1534796770-10295-4-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The I2C block transfer commands was not implemented correctly, it
read a length byte and such like it was an smbus transfer.
So fix the smbus_read_block() and smbus_write_block() functions
so they can properly handle I2C transfers, and normal SMBus
transfers (for upcoming changes). Pass in a transfer size and
a bool to know whether to use the size byte (like SMBus) or use
the length given (like I2C).
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1534796770-10295-3-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fix some spacing issues, remove extraneous comments, add some
defines instead of hard-coding numbers.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1534796770-10295-2-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rewrite to make it closer to how real device works so that guest OS
drivers can access I2C devices. Previously this was only a hack to
allow U-Boot to get past accessing SPD EEPROMs but to support other
I2C devices and allow guests to access them we need to model real
device more properly.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-8-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As well as being able to generate its own i2c transactions, the ppc4xx
i2c controller has a DIRECTCNTL register which allows explicit control
of the i2c lines.
Using this register an OS can directly bitbang i2c operations. In
order to let emulated i2c devices respond to this, we need to wire up
the DIRECTCNTL register to qemu's bitbanged i2c handling code.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We don't emulate slave mode so related registers are not needed.
[lh]sadr are only retained to avoid too many warnings and simplify
debugging but sdata is not even correct because device has a 4 byte
FIFO instead so just remove this unimplemented register for now.
The intr register is also not implemented correctly, it is for
diagnostics and normally not even visible on device without explicitly
enabling it. As no guests are known to need this remove it as well.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Make it more readable by converting register indexes to decimal
(avoids lot of superfluous 0x0) and distinguish errors caused by
accessing non-existent vs. unimplemented registers.
No functional change.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180606191801.6331-1-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is an helper routine to add a single EEPROM on an I2C bus. It can
be directly used by smbus_eeprom_init() which adds a certain number of
EEPROMs on mips and x86 machines.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180530064049.27976-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
I2CSlaveClass::init is no more used, remove it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180419212727.26095-3-f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180528144509.15812-3-armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SMBusDeviceClass::init is no more used, remove it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180419212727.26095-2-f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180528144509.15812-2-armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The tx function of the DDC I2C slave emulation was returning 1
on all writes resulting in NACK in the I2C bus. Changing it to
0 makes the DDC I2C work fine with bit-banged I2C such as the
versatile I2C.
I guess it was not affecting whatever I2C controller this was
used with until now, but with the Versatile I2C it surely
does not work.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Message-id: 20180227104903.21353-4-linus.walleij@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some devices need access to it.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Message-id: 20180227104903.21353-3-linus.walleij@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
