LAM uses CR3[61] and CR3[62] to configure/enable LAM on user pointers.
LAM uses CR4[28] to configure/enable LAM on supervisor pointers.
For CR3 LAM bits, no additional handling needed:
- TCG
LAM is not supported for TCG of target-i386. helper_write_crN() and
helper_vmrun() check max physical address bits before calling
cpu_x86_update_cr3(), no change needed, i.e. CR3 LAM bits are not allowed
to be set in TCG.
- gdbstub
x86_cpu_gdb_write_register() will call cpu_x86_update_cr3() to update cr3.
Allow gdb to set the LAM bit(s) to CR3, if vcpu doesn't support LAM,
KVM_SET_SREGS will fail as other reserved bits.
For CR4 LAM bit, its reservation depends on vcpu supporting LAM feature or
not.
- TCG
LAM is not supported for TCG of target-i386. helper_write_crN() and
helper_vmrun() check CR4 reserved bit before calling cpu_x86_update_cr4(),
i.e. CR4 LAM bit is not allowed to be set in TCG.
- gdbstub
x86_cpu_gdb_write_register() will call cpu_x86_update_cr4() to update cr4.
Mask out LAM bit on CR4 if vcpu doesn't support LAM.
- x86_cpu_reset_hold() doesn't need special handling.
Signed-off-by: Binbin Wu <binbin.wu@linux.intel.com>
Tested-by: Xuelian Guo <xuelian.guo@intel.com>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-ID: <20240112060042.19925-3-binbin.wu@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
monitor_puts() doesn't check the monitor pointer, but do_inject_x86_mce()
may have a parameter with NULL monitor pointer. Revert monitor_puts() in
do_inject_x86_mce() to fix, then the fact that we send the same message to
monitor and log is again more obvious.
Fixes: bf0c50d4aa (monitor: expose monitor_puts to rest of code)
Reviwed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Tao Su <tao1.su@linux.intel.com>
Message-ID: <20240320083640.523287-1-tao1.su@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
User emulation doesn't need any KVM declarations.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230904124325.79040-5-philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the #ifdef'ry inside do_cpu_init() instead of
declaring an empty stub for user emulation.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230602224628.59546-3-philmd@linaro.org>
Since commit 604664726f ("target/i386: Restrict cpu_exec_interrupt()
handler to sysemu"), do_cpu_sipi() isn't called anymore on user
emulation. Remove the now pointless stub.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230602224628.59546-2-philmd@linaro.org>
This will enable replacement of TARGET_INSN_START_WORDS in tcg.c.
Split out "tcg/insn-start-words.h" and use it in target/.
Reviewed-by: Anton Johansson <anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This had been pulled in from exec/cpu_ldst.h, via exec/exec-all.h,
but the include of tcg.h will be removed.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Anton Johansson <anjo@rev.ng>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230227135202.9710-8-anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Avoid cpu_restore_state, and modifying env->eip out from
underneath the translator with TARGET_TB_PCREL. There is
some slight duplication from x86_restore_state_to_opc,
but it's just a few lines.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1269
Reviewed-by: Claudio Fontana <cfontana@suse.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add a new hflag bit to determine whether AVX instructions are allowed
Signed-off-by: Paul Brook <paul@nowt.org>
Message-Id: <20220424220204.2493824-4-paul@nowt.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This helps us construct strings elsewhere before echoing to the
monitor. It avoids having to jump through hoops like:
monitor_printf(mon, "%s", s->str);
It will be useful in following patches but for now convert all
existing plain "%s" printfs to use the _puts api.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220929114231.583801-33-alex.bennee@linaro.org>
* Some small fixes for the qtests
* Misc header cleanups by Philippe
-----BEGIN PGP SIGNATURE-----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=/azS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/thuth-gitlab/tags/pull-request-2022-02-21' into staging
* Improve virtio-net failover test
* Some small fixes for the qtests
* Misc header cleanups by Philippe
# gpg: Signature made Mon 21 Feb 2022 11:40:37 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/thuth-gitlab/tags/pull-request-2022-02-21: (25 commits)
hw/tricore: Remove unused and incorrect header
hw/m68k/mcf: Add missing 'exec/hwaddr.h' header
exec/exec-all: Move 'qemu/log.h' include in units requiring it
softmmu/runstate: Clean headers
linux-user: Add missing "qemu/timer.h" include
target: Add missing "qemu/timer.h" include
core/ptimers: Remove unnecessary 'sysemu/cpus.h' include
exec/ramblock: Add missing includes
qtest: Add missing 'hw/qdev-core.h' include
hw/acpi/memory_hotplug: Remove unused 'hw/acpi/pc-hotplug.h' header
hw/remote: Add missing include
hw/tpm: Clean includes
scripts: Remove the old switch-timer-api script
tests/qtest: failover: migration abort test with failover off
tests/qtest: failover: test migration if the guest doesn't support failover
tests/qtest: failover: check migration with failover off
tests/qtest: failover: check missing guest feature
tests/qtest: failover: check the feature is correctly provided
tests/qtest: failover: use a macro for check_one_card()
tests/qtest: failover: clean up pathname of tests
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Many files use "qemu/log.h" declarations but neglect to include
it (they inherit it via "exec/exec-all.h"). "exec/exec-all.h" is
a core component and shouldn't be used that way. Move the
"qemu/log.h" inclusion locally to each unit requiring it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20220207082756.82600-10-f4bug@amsat.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
cpu_load_efer is now used only for sysemu code.
Therefore, move this function implementation to
sysemu-only section of helper.c
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210322132800.7470-22-cfontana@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Protection Keys for Supervisor-mode pages is a simple extension of
the PKU feature that QEMU already implements. For supervisor-mode
pages, protection key restrictions come from a new MSR. The MSR
has no XSAVE state associated to it.
PKS is only respected in long mode. However, in principle it is
possible to set the MSR even outside long mode, and in fact
even the XSAVE state for PKRU could be set outside long mode
using XRSTOR. So do not limit the migration subsections for
PKRU and PKRS to long mode.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
to do this, we need to take code out of cpu.c and helper.c,
and also move some prototypes from cpu.h, for code that is
needed in tcg/xxx_helper.c, and which in turn is part of the
callbacks registered by the class initialization.
Therefore, do some shuffling of the parts of cpu.h that
are only relevant for tcg/, and put them in tcg/helper-tcg.h
For FT0 and similar macros, put them in tcg/fpu-helper.c
since they are used only there.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20201212155530.23098-8-cfontana@suse.de>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
g_strdup_printf is used twice to write to the same variable, which
can theoretically cause a leak. In practice, it is extremely
unlikely that a guest is seeing a recursive MCE and has disabled
CR4.MCE between the first and the second error, but we can fix it
and we can also make a slight improvement on the logic: CR4.MCE=0
causes a triple fault even for a non-recursive machine check, so
let's place its test first.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023122801.19514-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Post memory failure event through QMP to handle hardware memory corrupted
event. Rather than simply printing to the log, QEMU could report more
effective message to the client. For example, if a guest receives an MCE,
evacuating the host could be a good idea.
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Message-Id: <20200930100440.1060708-4-pizhenwei@bytedance.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Previously we would only get a simple string "Triple fault" in qemu
log. Add detailed message for the two reasons to describe why qemu
has to reset the guest.
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Message-Id: <20200930100440.1060708-2-pizhenwei@bytedance.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is helpful when debugging stuck guest timers.
As we need apic_get_current_count for that, and it is really not
emulation specific, move it to apic_common.c and export it. Fix its
style at this chance as well.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <e00e2896-ca5b-a929-de7a-8e5762f0c1c2@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The SSE instruction implementations all fail to raise the expected
IEEE floating-point exceptions because they do nothing to convert the
exception state from the softfloat machinery into the exception flags
in MXCSR.
Fix this by adding such conversions. Unlike for x87, emulated SSE
floating-point operations might be optimized using hardware floating
point on the host, and so a different approach is taken that is
compatible with such optimizations. The required invariant is that
all exceptions set in env->sse_status (other than "denormal operand",
for which the SSE semantics are different from those in the softfloat
code) are ones that are set in the MXCSR; the emulated MXCSR is
updated lazily when code reads MXCSR, while when code sets MXCSR, the
exceptions in env->sse_status are set accordingly.
A few instructions do not raise all the exceptions that would be
raised by the softfloat code, and those instructions are made to save
and restore the softfloat exception state accordingly.
Nothing is done about "denormal operand"; setting that (only for the
case when input denormals are *not* flushed to zero, the opposite of
the logic in the softfloat code for such an exception) will require
custom code for relevant instructions, or else architecture-specific
conditionals in the softfloat code for when to set such an exception
together with custom code for various SSE conversion and rounding
instructions that do not set that exception.
Nothing is done about trapping exceptions (for which there is minimal
and largely broken support in QEMU's emulation in the x87 case and no
support at all in the SSE case).
Signed-off-by: Joseph Myers <joseph@codesourcery.com>
Message-Id: <alpine.DEB.2.21.2006252358000.3832@digraph.polyomino.org.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is a problem, that you don't have access to the data using cpu_memory_rw_debug() function when in SMM. You can't remotely debug SMM mode program because of that for example.
Likely attrs version of get_phys_page_debug should be used to get correct asidx at the end to handle access properly.
Here the patch to fix it.
Signed-off-by: Dmitry Poletaev <poletaev@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
sysemu/sysemu.h is a rather unfocused dumping ground for stuff related
to the system-emulator. Evidence:
* It's included widely: in my "build everything" tree, changing
sysemu/sysemu.h still triggers a recompile of some 1100 out of 6600
objects (not counting tests and objects that don't depend on
qemu/osdep.h, down from 5400 due to the previous two commits).
* It pulls in more than a dozen additional headers.
Split stuff related to run state management into its own header
sysemu/runstate.h.
Touching sysemu/sysemu.h now recompiles some 850 objects. qemu/uuid.h
also drops from 1100 to 850, and qapi/qapi-types-run-state.h from 4400
to 4200. Touching new sysemu/runstate.h recompiles some 500 objects.
Since I'm touching MAINTAINERS to add sysemu/runstate.h anyway, also
add qemu/main-loop.h.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-30-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
[Unbreak OS-X build]
Other accelerators have their own headers: sysemu/hax.h, sysemu/hvf.h,
sysemu/kvm.h, sysemu/whpx.h. Only tcg_enabled() & friends sit in
qemu-common.h. This necessitates inclusion of qemu-common.h into
headers, which is against the rules spelled out in qemu-common.h's
file comment.
Move tcg_enabled() & friends into their own header sysemu/tcg.h, and
adjust #include directives.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-2-armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[Rebased with conflicts resolved automatically, except for
accel/tcg/tcg-all.c]
Cleanup in the boilerplate that each target must define.
Replace x86_env_get_cpu with env_archcpu. The combination
CPU(x86_env_get_cpu) should have used ENV_GET_CPU to begin;
use env_cpu now.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
CPUClass method dump_statistics() takes an fprintf()-like callback and
a FILE * to pass to it. Most callers pass fprintf() and stderr.
log_cpu_state() passes fprintf() and qemu_log_file.
hmp_info_registers() passes monitor_fprintf() and the current monitor
cast to FILE *. monitor_fprintf() casts it right back, and is
otherwise identical to monitor_printf().
The callback gets passed around a lot, which is tiresome. The
type-punning around monitor_fprintf() is ugly.
Drop the callback, and call qemu_fprintf() instead. Also gets rid of
the type-punning, since qemu_fprintf() takes NULL instead of the
current monitor cast to FILE *.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190417191805.28198-15-armbru@redhat.com>
x86_cpu_dump_local_apic_state() takes an fprintf()-like callback and a
FILE * to pass to it, and so do its helper functions.
Its only caller hmp_info_local_apic() passes monitor_fprintf() and the
current monitor cast to FILE *. monitor_fprintf() casts it right
back, and is otherwise identical to monitor_printf(). The
type-punning is ugly.
Drop the callback, and call qemu_printf() instead.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190417191805.28198-12-armbru@redhat.com>
In icount mode, instructions that access io memory spaces in the middle
of the translation block invoke TB recompilation. After recompilation,
such instructions become last in the TB and are allowed to access io
memory spaces.
When the code includes instruction like i386 'xchg eax, 0xffffd080'
which accesses APIC, QEMU goes into an infinite loop of the recompilation.
This instruction includes two memory accesses - one read and one write.
After the first access, APIC calls cpu_report_tpr_access, which restores
the CPU state to get the current eip. But cpu_restore_state_from_tb
resets the cpu->can_do_io flag which makes the second memory access invalid.
Therefore the second memory access causes a recompilation of the block.
Then these operations repeat again and again.
This patch moves resetting cpu->can_do_io flag from
cpu_restore_state_from_tb to cpu_loop_exit* functions.
It also adds a parameter for cpu_restore_state which controls restoring
icount. There is no need to restore icount when we only query CPU state
without breaking the TB. Restoring it in such cases leads to the
incorrect flow of the virtual time.
In most cases new parameter is true (icount should be recalculated).
But there are two cases in i386 and openrisc when the CPU state is only
queried without the need to break the TB. This patch fixes both of
these cases.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Message-Id: <20180409091320.12504.35329.stgit@pasha-VirtualBox>
[rth: Make can_do_io setting unconditional; move from cpu_exec;
make cpu_loop_exit_{noexc,restore} call cpu_loop_exit.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Implements the WHPX accelerator cpu enlightenments to actually use the whpx-all
accelerator on Windows platforms.
Signed-off-by: Justin Terry (VM) <juterry@microsoft.com>
Message-Id: <1516655269-1785-5-git-send-email-juterry@microsoft.com>
[Register/unregister VCPU thread with RCU. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the tcg_enabled() where the x86 target needs to disable
TCG-specific code.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This function calls tlb_set_page_with_attrs, which is not available
when TCG is disabled. Move it to excp_helper.c.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move cpu_sync_bndcs_hflags() function from mpx_helper.c
to helper.c because mpx_helper.c need be disabled when
tcg is disabled.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This speeds up SMM switches. Later on it may remove the need to take
the BQL, and it may also allow to reuse code between TCG and KVM.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Ignore env->a20_mask when running in system management mode.
Reported-by: Anthony Xu <anthony.xu@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1494502528-12670-1-git-send-email-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Time to wire up all the call sites that request a shutdown or
reset to use the enum added in the previous patch.
It would have been less churn to keep the common case with no
arguments as meaning guest-triggered, and only modified the
host-triggered code paths, via a wrapper function, but then we'd
still have to audit that I didn't miss any host-triggered spots;
changing the signature forces us to double-check that I correctly
categorized all callers.
Since command line options can change whether a guest reset request
causes an actual reset vs. a shutdown, it's easy to also add the
information to reset requests.
Signed-off-by: Eric Blake <eblake@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au> [ppc parts]
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk> [SPARC part]
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com> [s390x parts]
Message-Id: <20170515214114.15442-5-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Move the generic cpu_synchronize_ functions to the common hw_accel.h header,
in order to prepare for the addition of a second hardware accelerator.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Message-Id: <f5c3cffe8d520011df1c2e5437bb814989b48332.1484045952.git.vpalatin@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We have never has the concept of global TLB entries which would avoid
the flush so we never actually use this flag. Drop it and make clear
that tlb_flush is the sledge-hammer it has always been.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
[DG: ppc portions]
Acked-by: David Gibson <david@gibson.dropbear.id.au>
The new paging more is extension of IA32e mode with more additional page
table level.
It brings support of 57-bit vitrual address space (128PB) and 52-bit
physical address space (4PB).
The structure of new page table level is identical to pml4.
The feature is enumerated with CPUID.(EAX=07H, ECX=0):ECX[bit 16].
CR4.LA57[bit 12] need to be set when pageing enables to activate 5-level
paging mode.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Message-Id: <20161215001305.146807-1-kirill.shutemov@linux.intel.com>
[Drop changes to target-i386/translate.c. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We've currently got 18 architectures in QEMU, and thus 18 target-xxx
folders in the root folder of the QEMU source tree. More architectures
(e.g. RISC-V, AVR) are likely to be included soon, too, so the main
folder of the QEMU sources slowly gets quite overcrowded with the
target-xxx folders.
To disburden the main folder a little bit, let's move the target-xxx
folders into a dedicated target/ folder, so that target-xxx/ simply
becomes target/xxx/ instead.
Acked-by: Laurent Vivier <laurent@vivier.eu> [m68k part]
Acked-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de> [tricore part]
Acked-by: Michael Walle <michael@walle.cc> [lm32 part]
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com> [s390x part]
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> [s390x part]
Acked-by: Eduardo Habkost <ehabkost@redhat.com> [i386 part]
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com> [sparc part]
Acked-by: Richard Henderson <rth@twiddle.net> [alpha part]
Acked-by: Max Filippov <jcmvbkbc@gmail.com> [xtensa part]
Reviewed-by: David Gibson <david@gibson.dropbear.id.au> [ppc part]
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> [crisµblaze part]
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn> [unicore32 part]
Signed-off-by: Thomas Huth <thuth@redhat.com>
