Update SeaBIOS-hppa to version 8.
Fixes:
- boot of HP-UX with SMP, and
- reboot of Linux and HP-UX with SMP
Enhancements:
- show qemu version in boot menu
- adds exit menu entry in boot menu to quit emulation
- allow to trace PCD_CHASSIS codes & machine run status
Signed-off-by: Helge Deller <deller@gmx.de>
Give current QEMU version string to SeaBIOS-hppa via fw_cfg interface so
that the firmware can show the QEMU version in the boot menu info.
Signed-off-by: Helge Deller <deller@gmx.de>
When the OS triggers a reboot, the reset helper function sends a
qemu_system_reset_request(SHUTDOWN_CAUSE_GUEST_RESET) together with an
EXCP_HLT exception to halt the CPUs.
So, at reboot when initializing the CPUs again, make sure to set all
instruction pointers to the firmware entry point, disable any interrupts,
disable data and instruction translations, enable PSW_Q bit and tell qemu
to unhalt (halted=0) the CPUs again.
This fixes the various reboot issues which were seen when rebooting a
Linux VM, including the case where even the monarch CPU has been virtually
halted from the OS (e.g. via "chcpu -d 0" inside the Linux VM).
Signed-off-by: Helge Deller <deller@gmx.de>
Analysis of the MacOS toolbox ROM code shows that on startup it attempts 2
separate reads of the seconds registers with commands 0x9d...0x91 followed by
0x8d..0x81 without resetting the command to its initial value. The PRAM seconds
value is only accepted when the values of the 2 separate reads match.
From this we conclude that bit 4 of the rtc command is not decoded or we don't
care about its value when reading the PRAM seconds registers. Implement this
decoding change so that both reads return successfully which allows the MacOS
toolbox ROM to correctly set the date/time.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-25-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
A comparison between the rtc command table included in the comment and the code
itself shows that the decoding for PRAM addresses 0x0 to 0xf is being done on
the raw command, and not the shifted version held in value.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-24-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the macfb device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-23-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Instead use the qdev_get_child_bus() function which is intended for this exact
purpose.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-22-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the mac-nubus-bridge device to use
object_initialize_child() and map the Nubus address space using
memory_region_add_subregion() instead of sysbus_mmio_map().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-21-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the SWIM device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-20-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the ESP device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-19-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the escc_orgate device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-18-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the ESCC device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-17-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the dp8393x device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: Jason Wang <jasowang@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-16-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This is to enable them to be used outside of dp8393x.c.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: Jason Wang <jasowang@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-15-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the VIA2 device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-14-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the VIA1 device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-13-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The current use of aliased memory regions causes us 2 problems: firstly the
output of "info qom-tree" is absolutely huge and difficult to read, and
secondly we have already reached the internal limit for memory regions as
adding any new memory region into the mac-io region causes QEMU to assert
with "phys_section_add: Assertion `map->sections_nb < TARGET_PAGE_SIZE'
failed".
Implement the mac-io region aliasing using a single IO memory region that
applies IO_SLICE_MASK representing the maximum size of the aliased region and
then forwarding the access to the existing mac-io memory region using the
address space API.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-12-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Move all devices from the IO region to within the container in preparation
for updating the IO aliasing mechanism.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the GLUE device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The use of the DEFINE_TYPES() macro will soon be recommended over the use of
calling type_init() directly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This will allow the q800-glue.h header to be included separately so that the
GLUE device can be referenced externally.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-8-mark.cave-ayland@ilande.co.uk>
[lv: update comment]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the CPU to use object_initialize_child()
followed by a separate realisation.
Restrict valid CPU types to m68040.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-6-mark.cave-ayland@ilande.co.uk>
[lv: update commit message]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This will enable us later to distinguish between QOM initialisation and machine
initialisation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This provides an overall container and owner for Machine-related objects such
as MemoryRegions.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This brings GLUEState in line with our current QOM guidelines.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Ensure there is a space before the final closing brace for all global
properties.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
from ISA v1.6.1 onwards the bit position of ICR.IE changed.
ctx->icr_ie_offset contains the correct value for the ISA version used
by the vCPU. We also need to exit this tb here, as we might have enabled
interrupts.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-Id: <20230621142302.1648383-9-kbastian@mail.uni-paderborn.de>
the CPU can change the privilege level by writing the corresponding bits
in PSW. If this happens all instructions after this 'mtcr' in the TB are
translated with the wrong privilege level. So we have to exit to the
cpu_loop() and start translating again with the new privilege level.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-Id: <20230621142302.1648383-8-kbastian@mail.uni-paderborn.de>
so we can recognize exceptions after re-enabling interrupts.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reported-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-Id: <20230621142302.1648383-4-kbastian@mail.uni-paderborn.de>
this replaces all calls to tcg_gen_exit_tb() and moves them to
tricore_tb_stop().
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-Id: <20230621142302.1648383-3-kbastian@mail.uni-paderborn.de>
if A[r1] == A[11], then we would overwrite the destination address of
the jump with the return address.
Reported-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-Id: <20230621142302.1648383-2-kbastian@mail.uni-paderborn.de>
We are always taking the TRICORE_FEATURE_13 branch as every CPU has TRICORE_FEATURE_13.
For CPUs with ISA > 1.3 we have to take the else branch.
We fix this by inverting the condition. We check for
TRICORE_FEATURE_131, which every CPU except TRICORE_FEATURE_13 CPUs
have.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1700
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-Id: <20230612113245.56667-5-kbastian@mail.uni-paderborn.de>
some insns were not checking if an even index was used to access a 64
bit register. In the worst case that could lead to a buffer overflow as
reported in https://gitlab.com/qemu-project/qemu/-/issues/1698.
Reported-by: Siqi Chen <coc.cyqh@gmail.com>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-Id: <20230612113245.56667-4-kbastian@mail.uni-paderborn.de>
we don't want to save PSW.CDC to the CSA, but PSW.CDE must be saved.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1699
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-Id: <20230612113245.56667-3-kbastian@mail.uni-paderborn.de>
When translating "imask" instruction of Tricore architecture, QEMU did not check whether the register index was out of bounds, resulting in a global-buffer-overflow.
Reviewed-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1698
Reported-by: Siqi Chen <coc.cyqh@gmail.com>
Signed-off-by: Siqi Chen <coc.cyqh@gmail.com>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-Id: <20230612065633.149152-1-coc.cyqh@gmail.com>
Message-Id: <20230612113245.56667-2-kbastian@mail.uni-paderborn.de>
this variant saves the 'IE' bit to a 'd' register. The 'IE' bitfield
changed from ISA version 1.6.1, so we add icr_ie_offset to DisasContext
as with the other DISABLE insn.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-Id: <20230614100039.1337971-9-kbastian@mail.uni-paderborn.de>
we also introduce the tc37x CPU that implements that ISA version.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-Id: <20230614100039.1337971-2-kbastian@mail.uni-paderborn.de>
This reverts commit d7ee93e243.
That commit tries to make a field in the CPUState struct not be
present when CONFIG_USER_ONLY is set. Unfortunately, you can't
conditionally omit fields in structs like this based on ifdefs that
are set per-target. If you try it, then code in files compiled
per-target (where CONFIG_USER_ONLY is or can be set) will disagree
about the struct layout with files that are compiled once-only (where
this kind of ifdef is never set).
This manifests specifically in 'make check-tcg' failing, because code
in cpus-common.c that sets up the CPUState::cpu_index field puts it
at a different offset from the code in plugins/core.c in
qemu_plugin_vcpu_init_hook() which reads the cpu_index field. The
latter then hits an assert because from its point of view every
thread has a 0 cpu_index. There might be other weird behaviour too.
Mostly we catch this kind of bug because the CONFIG_whatever is
listed in include/exec/poison.h and so the reference to it in
build-once source files will then cause a compiler error.
Unfortunately CONFIG_USER_ONLY is an exception to that: we have some
places where we use it in "safe" ways in headers that will be seen by
once-only source files (e.g. ifdeffing out function prototypes) and
it would be a lot of refactoring to be able to get to a position
where we could poison it. This leaves us in a "you have to be
careful to walk around the bear trap" situation...
Fixes: d7ee93e243 ("cputlb: Restrict SavedIOTLB to system emulation")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20230620175712.1331625-1-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
